Search Documents

By C. D. Rubert, W. J. Parton

A flotation plant was placed in operation in 1945 at the Tamaqua colliery of the Lehigh Navigation Coal Co. Inc., to recover fine anthracite which is discharged from the cleaning plant with the washery water.‡ In addition to the recovery plant, facilities were provided for the complete clarification of the washery water, recirculation of this clarified water for breaker use, and disposal of the refuse solids in a waste impounding dam. Fig I shows a view of the settling tanks and the flotation plant. Flow Diagram The flow diagram for the complete recovery project is given in Fig 2. All the waste water from the cleaning plant is collected in a sump A outside the breaker structure, from which a 7000 gpm pump B delivers it through a 16 in. line to a 75-ft diam hydroseparator C. The hydroseparator, acting as a classifier, is set to give a separation at approximately 200-mesh. The minus 200-mesh overflow is discharged by gravity into the 180-ft thickener D for final settling of the solids. The classifier underflow sludge is pumped to the flotation plant by a 6-in. quadruplex diaphragm pump E. A 10-ft diam hydroseparator F is used to make a second classification on the sludge solids at approximately 28-mesh. The underflow from this classifier containing the coarse particles is elevated by a 6-in. diaphragm pump G and is discharged on two 4- by 6-ft vibrating screens II. These screens are dressed with approximately 28-mesh cloth. Screen oversize product flows directly to the centrifuge that dewaters the cleaned froth. The screen underflow and the overflow from the 10-ft classifier flow to the flotation circuit. The flotation feed is conditioned in a 12 by 12-ft agitator tank J at a pulp density of I:2.33 (30 pct solids). Reagents are fed to the circuit by reagent feeder I. The conditioned pulp is then diluted to a pulp density of approximately I: 5 (18 pct solids) and is fed to two banks of four 100-cu ft froth flotation cells K for primary coal recovery and cleaning. Additional reagents from reagent distributor L are added to the feed weir-box of Nos. 2, 3, and 4 cells of each bank of flotation machines. Clean coal removed from these cells flows directly to the clean-coal sump. Dilute tailings from the primary cells is re-thickened in a 30-ft diam thickener M and is then retreated in a scavenger circuit for final recovery of coal. The scavenger circuit consists of a 6- by 6-ft agitator tank N and two banks of four 24-cu ft froth flotation cells 0. Coal froth from these cells flows to the dewatering equipment and the tailings flows to a vertical refuse pump which delivers it to the 180-ft diam waste thickener D. Dewatering of the coal products is accomplished in a 54- by 72-in Bird centrifugal filter P. The cake product is dropped onto a conveyor and is loaded

Jan 1, 1949

By W. N. Hiatt

The mathematical theory of the flow of two-phase, incompressible fluid through porous media is clarified, and the development of a general fluid displacement equation for two-phase, incompressible vertical flow through porous media is outlined. The relationship between the three components of the equation — the "fluid drive effect", the "gravity effect", and the "capillary effect'' — is discussed, as well as implications of the analysis in connection with the study of certain types of petroleum reservoirs. INTRODUCTION The purpose of this paper is to clarify and summarize the mathematical basis of the theory of two-phase incompressible fluid flow through porous media, particularly as it pertains to vertical flow, and to present a qualitative* exposition of the controlling factors involved in circumstances where this type of flow may exist. Although the generally accepted theory of heterogeneous fluid flow through porous media was developed a number of years ago by Muskat,1 and Buckley and Leverett2, 3 using the basic premise of Darcy, (and since then expounded upon by many others) there is a need for an over-all summary and clarification of this theory, especially regarding certain types of applications in connection with so-called "gravity-drainage-type reservoirs". The source and derivation is outlined for what is referred to here as the "General Fluid Displacement Equation for Incompressible Vertical Two-Phase Flow through Porous Media''. This equation would apply under the condition where the pressure drop along the path of flow is negligible in comparison with the pressure level on the system, or where compressibility and solubility effects are negligible. These conditions exist ordinarily in gravity-drainage-type reservoirs. Specifically, it will be shown that this general equation may be developed directly from the basic equations, which, according to present theory, govern the general case of viscous heterogeneous flow through porous media. This general equation has appeared in the literature previously, but in most cases its development from basic theory is not indicated clearly, or the equation is presented in terms of groups of constants and variables involving reduced or dimensionless quantities. This presentation is expedient in cases of experimental or computer applications; but it may make it difficult for the practicing petroleum engineer to identify all the factors involved or to understand the relationships between them. Therefore, in the following development, only ordinary mathematical parlance will be used, and no terms involving groups of other equations or reduced or dimensionless quantities will be used. DERIVATION The following equations for two-phase oil and gas flow result from analogy with Muskat's general equations,** if solubility and compressibility effects are neglected, and if all volumes are considered in terms of reservoir conditions, and the water phase, if present, is considered to be immobile (or effectively a part of the porous medium.) In this case, the sum of the oil and gas saturations may be taken as unity, and the saturation of each phase is in terms of the total hydrocarbon saturation. Note that in Eqs. 1 and 2, and in the derivation following, z is taken as positive in the vertically downward direction,

Jan 1, 1969

By J. P. Givry

The bath and the liquid metal in the aluw~inuw~ electrolytic cells are moving under the action of the Laplace forces. Consequently there are differences in level at the interface of the liquid. This phenomena is studied by means of a computer; the characteristics of the mathematical model used are presented with the results corresponding to two typical cases. This study gives a new and origi~zal interpretation of magnetic ej-jects; their action depends very closely on the hydraulic phenomenon which explain the sensibility of the cells to the slope and thickness of solid bath frozen around the pot. MAGNETIC effects produced in the electrolytic cells used for the production of aluminum are known to exist, a factor whose importance is well-known by producers through its influence on cell operation and output. In particular, these effects bring about movements in both the bath and metal as well as interface variations in level that are detrimental to sound electrolysis . A direct study of these effects by means of an experimental device would raise a number of problems particularly difficult not to say impossible to solve in the present state of techniques. It is for this reason that we had recourse to an electronic computer for working out the speed and pressure distribution within the liquid in the cells. We have assumed that all other possible causes for movement, such as thermal convection and evolution of gas at the anode, are acting without any connection with magnetic effects, and that consequently we may study each of these causes separately. A basic cause for magnetic effects lies in the presence of Laplace forces within the bath and metal. Electric current and magnetic field distribution have been calculated with the help of an electronic computer, and two communications about it have already been made to AIME.* 1) PRESENTATION OF THE MATHEMATICAL PATTERN In order to solve this problem, it was essential to assume a number of simplifying hypotheses with regard to both the geometry of the actual cells and the phenomena themselves. A first simplification consisted in assuming that the movements of the conducting liquid modify neither the electric currents nor the magnetic fields. In consideration of the magnitude of the values involved this assumption seemed accep-tible. 1.1) Finding the Equation of the Problem. The problem raised consisted in determining the flow of two viscous immiscible liquids with different densities subjected in a complex environment to gravity and Laplace forces. As a matter of fact, the sum of the external forces acting on the liquids is: F = JAB +pg where F = volume energy, B = magnetic field, J = current density, p = specific gravity, g = gravity. In the case of a laminar flow and assuming that the liquids are Newtonian and incompressible liquids, the equations governing movements are the following: 1) Navier Stokes' equation written in vectorial form: In fact one tries to find a steady-state solution, so aVx/at = 0; besides, one assumes that the movements are slow enough for quadratic terms such as Vy(a Vx/ay) (of round about the square of speed) to be neglected in front of the viscosity term: pAV, so

Jan 1, 1968

By Robert J. Linney

IN the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the " 21 " Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. 1, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously developed sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel to footwall and hanging wall to make a bench, spalling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig. 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore; by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1945

By Robert J. Linney

In the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the "21" Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. I, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously devel-oped sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel te footwall and hanging wall to make a bench, spdlling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore, by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1946

By D. Weinstein

Yieldilzg in annealed arc-cast molybdenunz in torsion was studied as a function of strain rate and tem-perature. The temperature dependence of the yield point for different strain rates was used to calculate a heat of activation for the yield point. The heat of activation was not a constant but was approximately a linear function of the stress at yield. It is proposed that the rate effect in yielding is determined in part by a site place-change of C (or other interstitial atom) in the metal. THE low-temperature embrittlement phenomenon in metals and alloys has been known to exist for a long time. Although a transition from ductile to brit-tle behavior has been observed in some close-packed hexagonal metals1 and a face-centered cubic alloy, the most common class of metals exhibiting this be-havior has a body-centered cubic lattice structure. For example, a ductile to brittle transition has been observed in iron,3 molybdenum,4 chromium,5 colum-bium,6 and tungsten.7 In the present investigation, molybdenum specimens were tested in torsion over a wide range of temperatures at three widely separated strain rates, and the temperature for onset of embrittlement was determined. Characteristic of body-centered cubic metals and closely associated with plastic deformation is the appearance of a sharp upper and lower yield point. Theoretical explanation of the yield point in iron and low-carbon steel is due to Cottrell,8 who attributes the phenomenon to the pinning of dislocations by the formation of impurity atmospheres around the dislocations. These atmospheres tend to lock the dislocations and make them more difficult to move. The stress required to move a dislocation and thereby cause plastic deformation is greatly increased, and thus an upper yield point is observed. In addition, theoretical analysis,9 as well as experimental observations, show that the upper yield point is strongly a function of temperature. The upper yield point is observed to decrease with an increase in testing temperature, and above a certain temperature (-700° K in iron) it no longer appears. This is consistent with the concept that thermal vibrations will help free a dislocation from its atmosphere, so that the external stress required to free a dislocation from its pinning atmosphere decreases with increasing temperature. Furthermore, with increasing temperature the equilibrium concentration of impurity atoms around a dislocation decreases exponentially with the result that the dislocation is less firmly pinned. In Cottrell's theory of yield point a static model is visualized in which the pinning atmospheres, particularly interstitial atoms, are immobile, and the dislocations are anchored to stationary positions in the lattice. However, experiments1,7 show the upper yield point to be time-dependent or a function of the rate of straining, a high strain rate causing a high upper yield point. Present theory does not adequately account for the rate dependence of the yield point, and the exact function of the interstitial atom is not under stood. Nevertheless, observation of the temperature dependence and rate dependence strongly suggests that the upper yield point phenomenon is due to the interaction between dislocations and pinning atoms, and that a diffusion mechanism is important in determining the yield point.

Jan 1, 1962

By Wendell S. Williams

Single crystals of TIC doped with boron at high temperat~ires develop second-phase inclusions. The inclusions are in the form of lamellae lying parallel to {l 11 } planes of the Tic matrix and can be vevealed by etching [100] cleavage faces of the boron-doped Tic crystals. measurements of the critical resolved shear stress. t, of TIC crystals containing such inclusions showed that the ropid drop in t wilh increasing temperatu.ve found for pure Tic was greatly reduced. At 1600°C, the inclusion containing crystals had a value of t five limes that of pure Tic. The hardening effect also was found to inhibit hot pressing of TiC powders containing boron impurity. Thermochemical and crys-tallographic arguments suggest that the inclusions are TiB2. The boron content of the hardened carbide is a few tenths of 1 pct. TITANIUM carbide is noted for its high room-temperature hardness. However, measurements of the critical resolved shear stress, T, of single crystals of Tic at high temperatures have shown that t decreases exponentially with increasing temperature.' This temperature dependence of t is attributed to thermally activated dislocation mobility limited by a large Peierls stress.' In turn, this large Peierls stress is believed to be a consequence of strong co-valent and ionic binding in Tic. The rapid drop in 7 with increasing temperature, characteristic of pure Tic, is lessened by the introduction of second-phase inclusions. Exposure of Tic to boron at high temperatures produces such inclusions. A report of the influence of boron on t in Tic is presented, followed by a discussion of the nature and formation of boron-containing inclusions in Tic which are believed to be responsible for the hardening effect. I) CRITICAL RESOLVED SHEAR STRESS OF BORON-DOPED Tic CRYSTALS Tic single crystal boules grown by Union Carbide Corp., Linde Division, were doped with boron by placing them in a carbon crucible packed with boron powder and heating in a vacuum furnace to 2000°C for 1 hr. Samples 1 by 1 by 3 mm were cleaved from these doped boules. High-temperature compression tests' were made on these samples to determine the critical resolved shear stress as a function of temperature . The rapid drop in critical resolved shear stress found for pure Tic crystals' did not occur: tests indicated that the boron-doped crystals at 1600°C had values of T equal to those of pure Tic crystals heated to only 1100°C, Fig. 1. No difference in the shape of the individual stress-strain curves was produced by the boron doping, but the stress scale was multiplied by a large factor. The hardening effect of boron in Tic probably extends to temperatures lower than those used in the present work (1100°C minimum). At room temperature, however, the influence of boron is difficult to determine because the stress required for gross plastic flow in pure Tic is SO high that in practice fracture cccurs first. Microhardness is the only test that can give an indication of the yield stress in Tic at room temperature. such measurements were made5 on boron-doped Tic; the matrix had a hardness value

Jan 1, 1967

By E. Buehler, J. E. Kunzler

High-pu.1-ity molybdenum has been heat treated, melted, and zone refined and the physical and chemical changes that are produced by these processes have been studied by making resistance ratio measurements. Pronounced effects are observed that are associated with recrystalliza-tion at about 1200°C and with melting. Melting alone is found to result in a substantial purification by the evaporation of impurities such as iron. Zone refining is found to be reasonably effective with four passes producing a three-fold decrease in resistance ratio and a minimum ratio of 0.0003. With the aid of low temperature measurenzents, it has been shown that the build-up of a deposit of the material being zone refined on the radio frequency coil used for heating can lead to contamination of the sample. CONSIDERABLE interest in high-purity refractory metals for the study of mechanical properties has developed during recent years. Also the need for highly pure metals in certain fundamental studies, such as electronic band structure, has become quite widely appreciated. Molybdenum can now be produced with sufficiently high purity to make it attractive for such investigations. The most suitable measure of chemical purity of metals used for many of these studies is its resistance ratio, R,.,o,/Ro, During the purification of molybdenum by zone refining and its subsequent evaluation by this technique, a number of informative observations were made. These observations concern the effectiveness of zone refining, the volatilization of impurities at the melting point, and the recrystallization of molybdenum and appear to be pertinent to other refractory metals. Also, the usefulness of low-temperature resistance measurements as an analytical tool for evaluating the presence of chemical impurities and physical defects in metals is again illustrated. Samples of high-purity molybdenum of known mechanical history were heated to various temperatures between 800°c and their melting point. Resistance ratios of the samples were measured after they had been given a specified treatment. The data were used, along with mass spectrographic analysis, as an aid in interpreting the nature of the processes that occurred in conjunction with each treatment. Changes in the concentrations of chemical impurities and physical defects are typical of things that effect the low-temperature resistivity. SAMPLES The starting material was obtained from Westing-house Corp., Bloomfield, N.J. It was in the form of molybdenum rods, usually 1/8 or 3/16 in. in diameter. These had been previously processed from bars, 5/8 in, in diameter, originally reduced from 4 in. diam arc-cast ingots, by hot swaging at about 1300°c. In the final step, the temperature was lowered to about l lOO°C which resulted in the production of elongated grains. Typical grains were about 0.03 mm thick and 0.6 mm long. The molybdenum was quite pure as is indicated by the results of mass spectro-scopic analysis1 given in Column 2 of Table I. Other nongaseous elements not listed in the table were not detected. ZONE REFINING AND THERMAL TREATMENT OF SAMPLES Several sample rods, 8 to 10 in. long, were zone refined or were heat treated at several temperatures. Both types of operations were performed using 3 me-

Jan 1, 1962

By C. H. Samans, G. F. Tisinai, J. K. Stanley

The times at which the first detectable amount of a phase forms at temperatures between 900° and 1800°F were determined. Both X-ray diffraction and metallography were used to detect a in highly strained filings; metallography alone to detect it in annealed bulk samples of six different types of stainless steels. The a phase was found to form in accordance with the C-type reaction curve in both austenitic and ferritic alloys. In filings of types 304, 347, and 446, a formed in a few hours, and in types 316, 309, and 310, it formed in a matter of minutes at temperatures corresponding to the knee of the C-curve. Only in the bulk type 309 steel, after 500 hr, and in the bulk type 310 steel, after as short a time as 25 hr at temperature, was n detected; in both instances at approximately the same optimum temperature as in the filings. The annealing temperature affected a phase nucleation only for the filings of type 304 and 347 steels, and for the bulk samples of type 309 and 310 steels. KNOWLEDGE of both the rate of nucleation and the rate of growth of the new phase is required for a complete description of metallurgical rate phenomena. However, data on the time for nucleation alone may frequently be useful in evaluating the tendency of commercial stainlcss steels to form s under various conditions. Very little correlated information of this type is available in the literature. Shortsleeve and Nicholson' indicate that s forms in ferritic 24, 27 and 30 pet Cr steels according to a C-type of reaction curve, and Emmanuel's' data for austenitic type 310 steel also suggest this type of solid state reaction. In addition, significant, though fragmentary, information has been given by Binder, Dulis and Smith,4 Payson and Savage,.; Guarneri, Miller, and Vawter,8 rerichs and Clark,7 Wilder,5 Lismer, Pryce, and Andrews,' Smith, Dulis, and Link,10 Dulis, Smith, and Houston," and Henry, Cordovi, and Fischer." The bearing of these data on this work is covered in the discussion. The purpose of this paper is to present such correlated data on s formation in AISI type 304 (18 pct Cr-8 pet Ni), 347 (18 pet Cr-10 pet Ni-Cb), 316 (18 pet Cr-12 pet Ni-2 pet Mo), 309 (25 pet Cr-12 pet Ni), 310 (25 pet Cr-20 pet Ni), and 446 (27 pet Cr) stainless steels. Materials and Test Methods X-ray diffraction and metallographic methods were used to determine the first appearance of the s phase in cold worked filings and in annealed bulk samples of seven steels, under various combinations of time and temperature. The rate of growth of the s particles was not determined. Commercial heats of six AISI steels and a low carbon laboratory experimental heat containing about 28 pet Cr were studied. Analyses are given in Table I. Because cold work greatly accelerates the nucleation of s particles, the relative rates of s nucleation in mechanically strained samples, i.e., filings through 120 mesh, were determined for direct comparison with those in annealed bulk alloys of the same composition.

Jan 1, 1957

By Charles H. Jacoby, Stanley J. LeFond

Salt, or halite, has a long and most varied history. While we know the Chinese were producing salt as early as 3000 B.C., the first written reference to salt appears in the book of Job recorded about 2250 B.C., which reads: "Can nothing which is unsavory be eaten without salt?" We do not know when man first used or realized that he needed salt. Perhaps one of our early Eolithic ancestors noted a piece of salt shining along the shore of a salt lake or a bay. He may have been attracted by its shining luster and tasted it. He found that it had a tart, zesty, distinctive flavor and perhaps chewing a large piece, became ill. However, by experimentation he soon learned that taken in the proper proportions salt was a very pleasant additive to his food. He may have noticed, too, that it increased his feeling of well-being. Thus, when the curtain of recorded history rises, we find man using salt for his health's sake, seasoning his food with it, feeding it to his animals, and using it in many superstitious and religious ceremonies. These uses, however, are a far cry from the uses for salt today. The first attempts of white man to make salt in continental United States were reported in the year 1614, while the first commercial production was in 1753 from the Kanawha licks. Practically all this salt was for human consumption, preserving food, and curing hides. Prior to the coming of the white man, Indians are known to have made salt from salt springs such as those that existed at Avery Island, LA, Charleston, WV, Saltville, VA, and Onondaga, NY. In 1862 the first rock salt was mined in the US from the Avery Island salt dome. Almost immediately thereafter, rock salt was mined at Saltville, VA and then at Retsof, NY in 1885. Of the more than 39 million tons produced annually in the United States, about 58% or 23 million tons are consumed by the chemical industry in the production of chlorine, caustic soda, hydrochloric acid, sodium metal, and some 30 other basic chemicals. These basic chemicals, in turn, are used in the preparation of approximately 14,000 chemicals which range from soap and detergents, to such chlorinated hydrocarbons as DDT, BHC, carbon tetrachloride, etc. Utilization of cavities created in salt beds and domes has grown rapidly since 1947 until now the waste salt is creating an ecological problem. The uses for both dry- and solution-mined cavities range from the storage of liquid hydrocarbons to containerized storage of toxic wastes, from compressed air for the peak shaving of power to storage of nuclear wastes. Geology Mineralogy Properties: Because of its simple structure, halite, the mineralogical name for salt, was the first structure to be analyzed by X-rays. It has the following properties: Formula: NaCl (Na-39.34%. Cl2-60.66% ) Crystallography: isometric, hexoctahedral, 4/m 32/m Space group: Fm3m A0: 5.627 kX Cell contents: Na4CI4 Habit: usually cubic, rarely octahedral, massive, granular to compact Physical properties: Refractive index: 1.554 Twinning: observed on {111} Cleavage: {001} perfect Fracture: conchoidal, brittle

Jan 1, 1983

By A. Kelly, S. Sato

Tensile tests have been performed on aluminum single crystals of 99.99 pct purity at 196°K. The resolved shear stress when the stress-strain curve becomes concave to the strain axis depends on orientation, being always higher for crystals with an initial orientation close to the sides of the unit triangle. Observations have been made, with the optical microscope, of the appearance of slip lines on polished surfaces of the crystals. Particular attention has been paid to the first appearance of cross-slip. It is confirmed that marked cross-slip is first seen when the stress-strain curve becomes concave to the strain axis. Measurements are reported of the lengths of the slip lines observed on top and side faces of the crystals at various stages of the deformation. The lengths of the slip lines vary inversely as the flow stress for all crystals, independent of crystal orientation. From measurements of the lengths and separations of the slip traces it is possible to estimate the number of dislocations which are annihilated at each cross-slip site. It is concluded that the annihilation of screw dislocations of opposite sign is the most important cross-slip process occurring. FRIEDEL1 recently pointed out that the stress-strain curve of many pure metals of face-centered-cubic structure can be considered as composed of three stages. Plastic flow commences with a region showing a small rate of hardening which is approximately linear. This has been called "easy glide*. It is followed by a region of more rapid hardening in which the slope of the curve is again approximately constant and this, in turn, is superseded by a final part of the curve which is concave to the strain axis. Following Diehl2 we may designate these regions as stages I, II, and III respectively. The onset of stage 111 occurs at lower stresses at higher temperatures. The appearance of the slip lines formed during these various stages has been described by a number of workers?-5* The object of the present work was to make detailed observations of the lengths and separations of slip lines for a number of crystals of different orientations deformed at the same temperature and strain rate. Although much previous work has been published on the deformation of aluminum single crystals the importance of measurements of these quantities has only recently been realized—they are essential for experimental tests of recent theories of work hardening.' 9 In aluminum, deformed at room temperature, stage 11 of the stress-strain curve is very weakly marked, as the stress for the onset of stage 111 is attained soon after the end of easy glide. In the present experiments it was decided to use a temperature lower than room temperature so that stage II of the curve was better developed. However, at temperatures as low as 90°K slip lines are not measured easily with the optical microscope.5 For this reason 1960k was chosen as a suitable temperature. Even at 1960k however, stage III of the curve commences at glide strains of 6 to 10 pct and hence

Jan 1, 1960

By H. F. Silliman, Daniel R. Hull, John R. Freeman

IN the normal operation of a brass-rolling mill, sheet and strip has, for the most part, been finished in comparatively thin gauges, involving a substantial amount of coldwork and a considerable number of anneals. This condition has been disturbed by the prep0nderance of cartridge brass, which is not rolled to thin gauges, and particularly by brass for artillery cartridge cases, on which the mill may finish its work at a thickness between 0.400 and 0.900 in. Obviously, the amount of rolling and the number of anneals to which such a product can be subjected are small compared with strip that is carried to a thickness of a few hundredths of an inch. As a result, critical examination into the internal condition of metal has been made on an extensive scale at a stage of manufacture that would not, in normal times, have been chosen for complete inspection. Under these conditions, a type of defect has been recognized that is not seen at thinner gauges. It might be more accurate to call it the appearance of a defect, since it refers to an apparently laminated, discontinuous structure, which, in fact, does not exist as such, and disappears after suitable treatment. For this reason it has been called a phantom lamination, which the authors consider an appropriate term. It is the purpose of this paper to describe the phenomenon and the conditions of its occurrence and, at least tentatively, to discuss its nature and cause. Great numbers of phantoms may be found in 2: 1 brass, either hot-rolled or cold-rolled. They are also found in 70-30 brass, sometimes when hot-rolled and generally when cold-rolled. It is not believed that phantoms are confined to these alloys but this paper is limited to them for the purpose of description. HOT-ROLLED 2:I BRASS For illustration, therefore, a typical cake of hot-rolled 2: 1 brass has been chosen. This was rolled to a slab 7/8 in. thick, from a casting 5 in. thick by 24 in. wide by 18 in. high, which was believed to have been sound. After hot-rolling and cooling, the slab was sheared and a portion of such a shear cut is shown in Fig. 1. It would be difficult to convince anyone viewing this specimen that the metal was not unsound. The impression would be confirmed by the appearance of a tensile break, as shown in Fig. 2. This is an ordinary tensile-test piece from metal just described. Although there was nothing in its tensile strength or elongation that suggested unsoundness, it appeared run through with pipes and laminations. To question the reality of such a condition would imply questioning the obvious. But, considering the history of the metal, it w0uld be difficult to believe that it could be so bad as it appeared. It seemed reasonable, though, that if the defects were what they appeared to be, they could be traced back from the sheared or broken face.

Jan 1, 1945

By J. B. Newkirk

ABOUT twenty-seven years ago W. bergl discovered that interesting detail could be seen in an X-ray diffraction spot made with a rock-salt crystal if the recording photographic film were held very close to the reflecting crystal. He also showed that much of this detail could be explained in terms of the deformation structure of the specimen. In the same year, 1931, Fox and parr2 reported that X-ray reflections from a quartz crystal were much more intense while the crystal was undergoing piezoelectric oscillation than when it was at rest. This observation was soon confirmed (and explained in terms of X-ray extinction) by Barrett3 in the United States and by Nishikawa et a1.,4 in Japan. During the next few years Barrett refined Berg's method for making X-ray diffraction micrographs and applied it to the study of metallic crystals. He reported this work in the 1945 annual lecture of the AIME.5 Since 1945 relatively little use has been made of the Berg-Barrett (B-B) method for making diffraction micrographs, though considerable interest in investigating subcrystal structures by other methods has developed. Some of these methods depend upon evaporation6 or chemical etching7 and, therefore, suffer from the occasional intrusion of subtle artifacts such as those recently reported by Hooker for leada and Welsh for aluminum.9 Other methods require the introduction of foreign elements which "decorate" the substructure in some way, thereby rendering it detectable by direct" or indirect1'. visual examination. Still others depend upon complex and often highly questionable analyses of X-ray diffraction line profiles. There have also been a number of related X-ray techniques, such as the Lambot,12 Schulz13 and Merlini and Guinier,14 which have proved to be quite useful for specific applications. Some of these methods give a picture of the substructure which is more or less directly related to the shape and the topography of the specimen. The Berg-Barrett method carries this desirable feature to the limit. Closely related to the B-B method are three photographic X-ray techniques recently described by Lang.15 These methods give beautiful pictures of the internal structure of crystals but are limited by the facts that the required apparatus is rather complex, exposure times are long, and the specimen crystals must be thin. An experimental appraisal which I have recently made of the original B-B method has shown that this simple technique is not only inexpensive and convenient, but can give more information than was apparently realized by its inventors. For example, first-order subgrains in iron-silicon crystals were clearly delineated and their relative orientation subject to description. Also defect structures could be seen within the subgrains and in some materials slip bands could be clearly seen with respect to the topography of the rest of the specimen. This much had already been described by Barrett. However, in the present study it was found that the actual sites of individual dislocations which emerge upon the crystal surface could be located. Furthermore, by a simple procedure, the direction (but not sign) of the dislocation Burgers' vector could be defined as well.

Jan 1, 1960

By C. D. Stahl, S. M. Farouq Ali, W. E. Culham

One- and two-dimensional mathematical models have been developed that simulate transient, two-phase flow of hydrocarbon mixtures in porous media in a manner that accounts for interphase mass transfer. Numerical simulations of one-dimensional depletion-drive experiments using a two-component hydrucarbon fluid were used to establish the validity of the mathematical models. In addition, the experimental and numerical data were used to demonstrate that production rate had a relatively insignificant effect on the recovery of individual hydrocarbon components from the experimental system, and that attainment of equilibrium between phases is possible for a wide range of liquid and vapor velocities in reservoirs containing light hydrocarbon fluids. Results of some two-dimensional numerical simulations are also presented. INTRODUCTION This study was undertaken to develop a mathematical model that would simulate transient, two-phase flow of hydrocarbon mixtures in porous media under conditions that result in interphase mass transfer and to test the validity of the assumptions used to set up the model. In addition, the study was designed to determine if production rate influences the recovery of individual hydrocarbon components from reservoirs producing by depletion drive. Two-phase flow in porous media, with interchange of components between the two phases, is important in many petroleum recovery processes. Studiesl-5 conducted within the last 3 years have outlined methods of solving multiphase flow problems incorporating mass transfer. Some of these studies have also indicated the importance of accounting for mass transfer under various producing conditions. An earlier work6 first demonstrated the importance of combining relative permeability data with equilibrium ratios in compositional balance methods. The mathematical model presented in this paper is formulated so that a phase behavior package, as described in previous papers,5,17 is not required as an integral part of the routine employed to solve for the primary dependent variables. The finite difference formulation is designed so that all the primary variables can be solved for simultaneously. This is accomplished by utilizing one basic set of equations. These innovations, which are in contrast to other models2,3,5 but are similar in some respects to the approach used by Taylor,l render the total problem computationally simpler than any of the previously referenced formulations. The mathematical model was developed by combining Darcy's law with a continuity equation for each hydrocarbon component. The principal assumptions invoked in the formulation were (1) that capillary forces and diffusional effects are negligible, and (2) that thermodynamic equilibrium exists in the reservoir at all times. No assumption as to the type of vaporization process was made in formulating this model. Experimental data were required to complete this study. These were generated by conducting several depletion drive experiments. The experimental apparatus consisted of a sandstone core enclosed in a pressurized casing. The apparatus was designed in such a manner that the core could be charged with a liquid hydrocarbon mixture and depleted at different production rates. The experimental tests were designed to determine the effect of production rate on component recovery. In addition, direct comparison of experimental and mathematically predicted

Jan 1, 1970

By R. H. Winn

A method for the selection of the most suitable corrosion inhibitor for a particular system is given. The method involves the evaluation of surface passivity by means of copper ion displacement after the metal surface has been subjected to the corrosive atmosphere. The application of the method to the selection of suitable inhibitors for use in producing wells is described. Correlation with recognized laboratory tests has beet1 found to be good within the limitations of the test. The use of the test to evaluate inhibitor persistencc is described. INTRODUCTION Corrosion as it is associated with the industry shows wide variations in its qualitative as well as its quantitative aspects. This complicates the work of the corrosion engineer. In the past few years the efforts of the corrosion engineer have been further taxed by the large numbers of products being marketed as corrosion inhibitors by various manufacturers. These products are submitted to him together with a limited amount of data to support their use as inhibitors. The data are usually authentic and reliable yet all too often when these products are applied to an actual corrosive system the results are disappointing due to the ineffectiveness of the inhibitor and the corrosive system. The corrosion engineer must select a comparatively limited number of inhibitors for field trial from the large number available. The selection is usually made on the basis of a standardized laboratory test such as that adopted by the National Association of Corrosion Engineers or by field experience in an area; however, testing of this type is discouraging on large numbers of compounds, particularly in view of the specificity of environment. It has been an object of this work to devise a method which will allow the corrosion engineer to select the best inhibitor for a specific environment under field conditions. The test would of necessity be rapid and inexpensive. It would preferably eliminate the need for expensive and delicate instruments. STATEMENT OF THEORY The test as developed makes use of the fact that metal ions will be displaced from solution by metals having a more positive electrode potential. Thus, if an active iron surface is exposed to a solution of a copper salt, free copper will plate spontaneously on the iron surface as it is displaced from the salt solution by iron ions. If the iron surface is passified, as by coating with an insulating-type organic corrosion inhibitor, it is no longer capable of displacing the copper ions due to its own limited ionization. The result will be a change in the amount of copper plated upon exposure to a neutral copper salt solution. In practice it has been found possible to measure the magnitude of the alteration of the cell potential by determining the copper deposited on a standard iron surface under controlled conditions. This means that, as the film builds up, the resulting shift in the electrode potential tends to cause the iron surface to act more like a noble metal, resulting in a reduction in the cell potential to a point that copper will no longer plate spontaneously. Obviously, the salts of other metals such as silver, gold or platinum might be used for this operation; however, copper was selected because of the color difference of the plate, the comparatively low cost of copper salts and the ease of evaluation of the plated copper. Furthermore, its high cell potential provides a substantial driving energy. The determination of the copper is readily done colorimetrically by dissolving it in 5 per cent ammonium hydroxide solution containing 2 per cent potassium per-sulfate. The blue color of the copper ammonic complex ion so developed may be compared with standards prepared by dissolving known quantities of copper powder in the same reagent. In routine screening it is seldom desirable to determine the amount of copper plated. It is usually more important to determine the concentration of inhibitor required to prevent the plating of copper.

By AIME AIME

Report of Committee 24, of the International Association for Testing Materials, presented at the Brussels Congress, 1906. Republished for use at the 94th Meeting of the American Institute of Mining Engineers, New York, N. Y., February, 1908. Discussion by letter is requested by the Secretary of the Institute. The Committee appointed for the solution of Problem 24 consisted of the following members Prof. H. M. Howe, New York, N. Y. (Chairman); L. Levy, Paris, France (Vice-Chairman) ; Prof. D. Tschernoff, St. Petersburg, Russia (Vice-Chairman) ; Prof. Albert Sauveur, Cambridge, Mass. (Secretary) ; Van Drunen, Ixelles, Belgium; Lieut.-Col. H. Tusen, Copenhagen, Denmark ; E. P. Martin, Abergavenny, England ; A. Pourcel, Paris, France ; H. Brauer, Dortmund, Germany ; Dr. Prof. H. Wedding, Berlin, Germany; P. Verole, Milan, Italy ; A. Baalsrud, Christiania, Norway ; A. R. v. Dormus, Vienna, Austria ; A. Sailler, Vienna, Austria; Bureau des Forges, St. Petersburg, Russia; Prof. N. Belelub-sky, St. Petersburg, Russia ; N. Jossa, St. Petersburg, Russia ; Maj.-Gen. M. Korobkoff, St. Petersburg, Russia ; S. Smirnoff, St. Petersburg, Russia ;.Ladislaus v. Tetmajer, Budapest, Hungary ; H. H. Campbell, Steelton, Pa. Early in February, 1905, a list of species and varieties of iron and steel, with definitions, drawn by the Chairman and Secretary of Committee 24, was sent to every member of this Committee with a request for comments and suggestions. A special request was sent to the following gentlemen . for the equivalents in their several languages of these species and varieties : A. , Pourcel, Paris, France; Prof. H. Wedding, Berlin, Germany ; J. A. Brinell, Stockholm, Sweden ; Prof. H. I. Hannover, Copenhagen, Denmark; Prof. P. Kley, Delft, Holland; P. Verole, Milan, Italy; Col. Cubillo, Trubia, Spain. This present report, which is based upon our original list and definitions, and upon the replies to these requests, consists of four parts I. A polyglot, which gives the names of the chief classes of iron and steel in English, French, German, Swedish, Danish and Dutch. We .regret that we have failed to get the Italian and Spanish names. II. English definitions of principal classes of iron and steel. III. A glossary of special sizes and shapes of iron and steel. IV. A note on the boundary between steel and cast-iron. I. POLYGLOT, IN ENGLISH, FRENCH, GERMAN, SWEDISH, DANISH AND DUTCH, OF THE CHIEF CLASSES OF IRON AND STEEL, AND OF THE APPARATUS IN WHICH THEY ARE MADE. This list is not intended to be complete, but rather to include only those varieties which are of interest to the Association.

Mar 1, 1908

The Institute would he glad to purchase from any Member a copy of the Bulletin for May, 1914.

Jan 5, 1917

By W. T. Bell, M. P. Lebourg

The perforating of multiple tubingless completions, in which two or more strings of 27/8-in. OD casing are installed in the same borehole, presents two basic problems. First, good completion practices require an eficient perforator that leaves no debris to interfere with subsequent completion operations. Second, and of more complicated nature, a system is needed for controlling the direction of fire so that adjacent strings are not damaged. Development of of a 2-in. OD, steel retrievable, shnped-charge gun has solved the first problem. The second was resolved through development of three different devices to provide directional perforating for the two types of completion methods being employed today. These include a mechanical orienting device and two self-orienting radiation devices. Conceivably, the latter methods could be adapted to the directional perforating (of .upper zones) of conventional dual and triple completions without removing production tubing and packers. INTRODUCTION The recent trend to multiple tubingless completions,' wherein two or more strings of 27/8-in. OD casing are installed in the same borehole, has presented two basic perforating problems. The first problem to be overcome was the design of a gun that would result in efficient perforations without causing debris to bridge in these small-diameter casings. The second problem was, of course, to devise a system for controlling the direction of fire such that adjacent strings would not be damaged. The problem of gun debris in slim-casing completions has been well defined in the numerous 27/8-in. single tubingless completions which have been effected during recent years with the expendable-type perforators. Failure of expendable-gun debris to settle out properly, even with good gun break-up, has resulted in bridging inside these small-diameter casings. This, in turn, has interfered with completion and re-conditioning operations. The past two years have clearly shown, in fact, that debris problems are not confined to this small range of casing with most designs of expendable-type guns. A high incidence of bridging has even been reported in 4%-in. OD casing. The perforating of multiple tubingless completions has entailed, therefore, the development of a completely debris-free gun of adequate performance, as well as the necessary devices to provide positive directional perforating in the two completion methods presently being employed. THE GUN —DESIGN CONSIDERATIONS The design of a shaped-charge gun for slim-casing perforating has presented a maze of interrelated prob-lems. Since the primary specification has been leveled at efficient charge performance with complete elimination of gun debris, it has been necessary to develop a retrievable steel-carrier gun of tubular construction to house the charges. The carrier must be retrievable through 2.29-in. API pump-seating nipples which are usually installed in 2 7/8-in. strings. To provide for recovery of the gun from the well, swelling of the carrier on firing must be carefully controlled. Control of swelling automatically means control of explosive weight in the shaped charge which, in turn, influences charge performance. Carrier swelling also depends upon the confinement pressure at the level being perforated, which imposes a hydrostatic pressure-depth limitation. Burr interference on the wall of the carrier, resulting from passage of the jet through the carrier wall, must be eliminated by suitable design. Clearly then, a satisfactory shaped-charge gun design for slim-casing operations represents a fine balance between carrier swelling, hydrostatic pressure, explosive weight and charge performance. Additionally, to lend itself to directional perforating, the gun design must provide a positive locking mechanism for individual charges within the gun carrier. This fixes charge orientation within the carrier and prevents

By D. H. Newland

New York has a small but not insignificant place in the oil and natural gas industries of the United States. It has had a continuous record as an oil producer since 1872, with an aggregate yield of about 104,000,000 bbl. The reported output for 1935 was 4,237,000 bbl., a gain of more than 10 per cent for the year and a total that has been exceeded only in the early period of flush production half a century ago. The industry has been steadily building up since 1920 with the successful practice of the water drive, which has given a new lease of life to pools that had been practically drained of oil recoverable by pumping. An additional output of 2000 bbl. or more per acre is being procured by this method. Altogether the fields in New York State cover about 55,000 acres. Their limits are well defined and it is unlikely that they will be extended in the future, although there is some prospect of finding additional supplies by deeper drilling. The oil from New York is all classed as Pennsylvania grade, for which the recent price has been about $2.50 a barrel. It is refined at Olean, Wellsville and Bolivar, in the oil district, and partly in Pennsylvania refineries. Exploration for natural gas, outside of the established districts, was considerable during the year. Altogether 59 wells were drilled, distributed over 13 counties, of which 33 were listed as producers and 26 were dry. At the close of the year, 13 wells were in process of drilling. The 33 producing wells had a combined estimated flow of 278 million cubic feet per day. The best results were obtained from exploration in Allegany County, where out of eight wells drilled to the Oriskany sandstone five were successful and showed a combined open-flow capacity of 107 million cubic feet. The Oriskany sandstone was encountered at a depth of 4500 to 4900 ft. In Steuben County, next east of Allegany County, two out of seven wells to the Oriskany proved productive, and one of these, in the town of Greenwood, on the Watkins structure, was probably the largest that has so far been opened in the state, with a reported yield of 35 million a day. In the central part of New York interest was awakened by the activity shown in exploring for gas in the Trenton limestone, in Camden, Florence and Rome townships, Oneida

Jan 1, 1936

By F. L. Bosqui

A. L. BlomFIeld, Denver, Col. (communication to the Secretary.*) — Mr. Caldecott says on p. 67: "The Dorr thickener shown, while a useful device when crushing with cyanide solution for removing surplus solution from slime pulp prior to air-lift agitation or vacuum filtration, is not adapted to effect as complete a separation of water from settled slime as the ordinary intermittent settlement and decantation." This statement might have passed muster in this country several years ago when. the Dorr thickener was a new device, but its use in hundreds of mills in the United States has demonstrated that as thick a product is being discharged from it as was obtained from the intermittent settling which it has supplanted. • It is interesting to note that recent investigation, especially the work of 11. 6. Coe and G. H. Cleveilger,' in the March Bulletin of the Institute, under the title: Laboratory Method for Determining the Capacities of Slime Settling Tanks, has developed the general theory of settlement and explains the results obtained in practice. Just as free settlement is a function of surface area, so thickening after the zone of free settlement is passed is a function of time. The time required is obtained by the capacity or volume provided in the settler for this thickening zone. Each pulp is a problem in itself, both in regard to free settlement and to time required to reach a commercially finished thickness. Some pulps require 48 hr. and more to reach a density of 40 per cent. solids; others no coarser to the screen test reach a density of 65 per cent.' solids in a fraction of that time. In thickening any pulp a point is reached where the increase in density is so slow as to be commercially unprofitable. When any part of the pulp has reached this point it should pass on for treatment—its place in the thickener should be occupied by pulp which has not yet reached the commercial limit. By doing this the whole volume of the settling tank is kept in active use. Thus the continuous thickener keeps the whole tank at work to its commercial limit, while the intermittent settler has much of its volume occupied at times by pulp which is either quite finished thickening or at least thickened past the commercial point. The mechanical efficiency of the continuous thickener can be the only argument for limiting this statement. In my own experience I have never

Jan 1, 1916