Search Documents

By Kenneth A. Gutschick, Robert S. Boynton

Lime has become a general and loosely used term to denote almost any kind of calcareous material or finely divided form of limestone or dolomite, as well as burned forms of lime. However, according to Webster, lime is only calcined limestone (known as quicklime, unslaked lime, or calcium oxide). It also embraces the secondary product of quicklime, i.e., hydrated lime or slaked lime (calcium hydroxide). There are two basic types of limestone used for lime manufacture-high calcium and high magnesium (dolomitic). The dolomitic quicklimes and hydrated limes correspond to their "high calcium" counterparts. The only difference is that the dolomitic types are a combination of the elements calcium and magnesium, in varying percents, whereas high calicum limes contain less than 5% MgO down to 1/2%. In either case a pure form of limestone of at least 97% combined carbonate content is needed to make salable lime, barring a few exceptions. The calcination of both types is diagrammed chemically as follows: [ ] In the foregoing reversible reactions the limestone is burned (calcined) in lime kilns, with the carbon dioxide content of the stone expelled as a gas. The weight loss during calcination of pure high calcium limestone is 44%; with equimolecular dolomitic limestone, the weight loss is 48%. Since lime has a strong affinity for CO_, particularly if moisture is present, it will readily revert to its original carbonate form. This occurs when quicklime "air-slakes" and adsorbs CO.. from the air. Thus, quicklime is perishable and should be stored in dry, water-tight areas. Depending upon the type of kiln used and the physical structure of the stone, the size of the quicklime may range from sandlike granules to 8 in. lumps. However, pebble sizes ranging from 1/4 in. to 2 in. are the most common. Screened quicklime fines are also com¬pressed (pelletized) into 1 in. pellets. For some purposes ground or pulverized forms of quicklime are used, ranging from No. 10 mesh to dust. Generally a pebble of quicklime is about the same size as the pebble of limestone before calcination (perhaps shrinking slightly). A more stable form of lime is hydrated lime. This is obtained by adding water to quicklime, slaking it into a dry, fine, subsieve size white powder. Because its affinity for moisture has been satisfied, it is not vulnerable to further moisture like quicklime. However, it has the same strong affinity for CO_. The following reversible chemical reactions illustrate how hydrated lime when heated (or dehydrated) can revert to the original oxide form:

Jan 1, 1975

By George B. Langford

The McIntyre mine is in the Pearl Lake section of the Porcupine gold area. The rocks are Keewatin lavas intruded by quartz porphyries and albitite dies of Algoman age. Gold-bearing quartz veins are found in the Keewatin rocks near the porphyry stocks. The whole area has been highly compressed by forces acting along a N. 20°W. line. These forces folded the Keewatin rocks before the intrusion of the Algoman rocks, and later schisted both the Keewatin and Algoman rocks. Vein fractures were developed after the folding but before the development of the schist by the compres-sive forces being locally broken up into couples. These couples were set up by the differential resistance to deformation of porphyries and basalts, and also by the competency of the dacites and incompetency of the tuffs and fragmental rocks. During the important period of vein formation, two zones were developed—an inner productive zone in which the quartz veins are ankerite-bearing and an outer barren zone in which the quartz veins are calcite-bearing. The vein solutions originated in the same magrna that supplied the albitite dikes. Introduction The McIntyre mine, in the Porcupine gold area of northern Ontario, has passed its twenty-sixth birthday and has been producing gold since early in 1912. During this time approximately ten million tons of ore has been mined and over three and a half million ounces of gold recovered. This amount of ore would be sufficient to fill 2300 standard railway freight trains, each of 100 cars, and the gold produced, although only equivalent to a cube 51/2 ft. to the side, would weigh approximately 100 tons, a load for three freight cars. Silver has been produced in the ratio of 1 oz. of silver to every 4.4 oz. of gold, so that the total silver recovery is in the neighborhood of 700,000 ounces. The early history of the mine, like that of many others, shows that for several years it fought an uphill struggle for existence. One of the important features in winning this fight was the early recognition of some of the geological conditions responsible for the ore deposits, and the application of this knowledge in the search for ore and in the acquiring of adjoining properties. As early as 1913—only two years after the mine was opened—a geological department was organiaed. It has functioned almost continuously since that date and has demonstrated the importance

Jan 1, 1941

By A. C. Bulnes

This paper applies the methods of statistical analysis to the interpretation of core analysis data of dolomitic limestone from the San Andres formation at Wasson and the Clearfork formation at Fullerton. Probability relationships are shown to connect the porosity and the permeability and the porosity and the fluid saturation. For example, the porosity-permeability relationship expresses the probability that a sample of porosity,f, will or will not be permeable. The over-all porosity frequency distribution of the reservoir together with the frequency curves of permeability (one for each class interval of porosity) provide a precise basis for computing the weighted average productive porosity of the reservoir for any assigned value of the minimum productive permeability. The probability that the permeability of a core specimen from Fullerton will exceed a given value appears to be dependent on the percentage porosity of the specimen, its void structure type (i.e., porosity in the qualitative sense), and the given value of the permeability. If continuous profiles of void structure type and porosity are available together with the appropriate porosity-probability of permability plots, the nes pay thickness may be estimated. The Invasion Index of a well is defined in terms of the porosity and permeability data. This index is suggested as a basis for comparing wells as regards their suitability as fluid-injection wells. Three problems of importance in the exploitation of limestone reservoirs may be stated as follows: 1. The determination of the productive porosity of the reservoir. The productive porosity is defined as f = fPVP/V [II in which Vp, is the volume of the reservoir that is sufficiently permeable to oil to give up an appreciable fraction of its original oil in place during the economic life of the reservoir; fp, is the arithmetic mean porosity of the permeable volume v*, and V is the total volume of the reservoir. 2. The determination of the number of feet of oil-bearing porous rock that will produce at a commercial rate into the well bore; i.e., the net pay thickness. 3. The choice of fluid-injection wells in a secondary recovery program. The ultimate recovery of the reservoir is proportiona1 to the productive porosity. The productive capacity of the well is proportional to the net pay thickness. The principal purpose of this paper is to show that the methods of statistical analysis when applied to core analysis data of dolomitic limestones offer a useful approach to the solution of these three problems, as well as others of importance in reservoir engineering. The use of these methods was suggested by the work of Jan Law.1

Jan 1, 1946

By Harry L. Brown, James M. Dickinson, Philip E. Armstrong

The elastic stiffness coefficients of niobium have been rneaslrred from -150°C to over 650 C and ave in accord with the anomalous temperature dependence previously observed for Young's modulus. This unusual behavior has been shown to be the result of changes in the relative values of the shear elastic coefficients. The bulk modulus remained essentially constant over the temperature range studied, while changes in the shear coefficients produced a more nearly isotropic behavior as the temperature increased. A number of investigators have reported data on the temperature dependence of Young's modulus of polycrystalline niobium. The values cited for the room-temperature modulus ranged from 0.71 to 1.17 x 10" dynes-cm-' (10.3 to 17.0 x lo6 psi) and in each case the modulus was observed to decrease with increasing temperature. In our recent study,8 both polycrystalline and single-crystal samples of essentially strain-free high-purity niobium showed a Young's modulus whose temperature dependence as well as magnitude was strongly dependent on specimen orientation. This was shown to be the result of changes in the relative magnitude of the two shear moduli, C and C'. Young's modulus of polycrystalline samples with strong [110] textures and Young's modulus of single crystals whose orientations were away from the [loo] actually increased as much as 12 pct between room temperature and 1000°C. While studies on the residual effects of previous fabrication, thermal treatments, and impurity contents will probably resolve the problem of the widely differing Young's modulus values observed in polycrystalline niobium, a more complete description of the elastic properties requires an evaluation of the single-crystal elastic constants. A knowledge of these constants can provide a clearer picture of the nature of the temperature dependence, as well as establish a basis for predicting the modulus behavior of polycrystalline niobium, both in the randomly oriented condition and with various fabrication textures. The effects of residual strains on the elastic behavior then can be separated from orientation effects. EXPERIMENTAL METHOD Thin rod-resonance techniques were used to obtain both the Young's modulus and shear modulus of single-crystal specimens. The determination of these moduli as functions of the crystallographic orientation of the specimen axis provided sufficient information to permit calculation of the single-crystal elastic constants. The necessity for torsional as well as longitudinal measurements led to the design and assembly of a vertical-tube vacuum furnace incorporating probes for the simultaneous determination of both longitudinal

Jan 1, 1967

By Charles T. Baroch, Charles J. Baroch

In 20 years of commercial development, nuclear reactors have demonstrated that they are a safe, dependable, and economical source of power. Operating experience with commercial power reactors has firmly established nuclear power as a practicable source of energy. For both boiling-water (BWR) and pressurized-water (PWR) reactors, performances to date have generally met design predictions. Furthermore, it has become possible to analyze and understand the nuclear, chemical, and physical behavior of this class of reactors. The United Kingdom has had similar success with gas-cooled reactors. The Experimental Boiling Water Reactor (EBWR), the first United States experimental power reactor, began operation in 1956. It proved to be capable of supplying 4500 kw (kilowatts) of power. This reactor was followed in 1957 by the Pressurized Water Reactor at Shippingport, Pa. It was the nation's first full-scale central-station nuclear power plant and the first in the world designed exclusively for the production of civilian electric power. The Shippingport reactor was originally designed to produce 60 megawatts (MW) of electricity, and it was increased to 100 MW in 1964. In 12 years of operation, this reactor generated over 4.5-million MW-hr of electricity in spite of many shutdowns for experimental alterations. By 1969, a total of 15 central-station nuclear power reactors were operable in the United States with an aggregate electrical capacity of over 4200 MW. Early in 1964, Jersey Central Power & Light Co. announced plans for constructing a 515-MW nuclear plant at Oyster Creek, N.J., to be built without government financial assistance. The company stated that a nuclear plant had been selected competitively with fossil fuel. Their economic analysis stated that the plant would generate electricity at less than 4 mills per kw-hr, competitive with coal at 200 per million Btu (British thermal units). Coal cost in 1964 for that region averaged 26.00 per million Btu. The Jersey Central report created wide interest in public-utility circles; nevertheless, no other nuclear plants were announced in 1964. However, in 1965, six nuclear plants were announced by utilities, followed by 26 in 1966, 29 in 1967, and 10 in 1968. By Sept. 30, 1969, 97 reactors were operable, being built, or planned. The cost of these, all committed by electric utilities, was estimated at about $12 billion. When constructed, they will have an electrical capacity of 72,000 MW. The unprecedented surge in power reactors that started in 1965 tapered in 1968, and only seven reactors were announced in

Jan 1, 1976

By H. F. A. Hergt, K. L. Sutherland, J. Rogers

In 1938 Ralston4 reviewed the many attempts to find a satisfactory collector for the separation of cassiterite from its ores and in 1944 Dean and Ambrose2 summarized some further attempts. Generally, soaps and amines are effective but nonselective collectors. We have discovered that reagents containing either the polar group — SO4- or — SO3- are excellent collectors for cassiterite and promise to be selective. The response to these reagents of cassiterite and of minerals commonly associated with it was studied, using the captive-bubble technique. Using these fundamental data, the practicability of separation and concentration of tin was investigated by flotation tests in a 2000-gram Denver cell. Experimental Methods Reagents All inorganic reagents were of Analar grade. The preparation and purification of sodium cetyl sulphate, cetyl trimethyl-ammonium bromide, laurylamine and cetylamine have been previously described.5 The other collectors were commercial surface-active agents, which were used without purification. Tests Captive-bubble Tests and Cylinder Flotation Tests have been previously de- scribed.5,10 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible, by a cross, and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, and the experimental results are indicated by a square. The curves show the limits of composition of solutions in which flotation in a cell would be possible but many factors other than those considered in these the determine recovery and grade of a given mineral in practice. Flotation Tests in 500 and 2000-gram Denver SUbmachines,—Melboume tap water, containing 12 parts calcium, 6 parts

Jan 1, 1947

By J. Rogers, H. F. A. Hergt, K. L. Sutherland

In 1938 Ralston4 reviewed the many attempts to find a satisfactory collector for the separation of cassiterite from its ores and in 1944 Dean and Ambrose2 summarized some further attempts. Generally, soaps and amines are effective but nonselective collectors. We have discovered that reagents containing either the polar group — SO4- or — SO3- are excellent collectors for cassiterite and promise to be selective. The response to these reagents of cassiterite and of minerals commonly associated with it was studied, using the captive-bubble technique. Using these fundamental data, the practicability of separation and concentration of tin was investigated by flotation tests in a 2000-gram Denver cell. Experimental Methods Reagents All inorganic reagents were of Analar grade. The preparation and purification of sodium cetyl sulphate, cetyl trimethyl-ammonium bromide, laurylamine and cetylamine have been previously described.5 The other collectors were commercial surface-active agents, which were used without purification. Tests Captive-bubble Tests and Cylinder Flotation Tests have been previously de- scribed.5,10 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible, by a cross, and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, and the experimental results are indicated by a square. The curves show the limits of composition of solutions in which flotation in a cell would be possible but many factors other than those considered in these the determine recovery and grade of a given mineral in practice. Flotation Tests in 500 and 2000-gram Denver SUbmachines,—Melboume tap water, containing 12 parts calcium, 6 parts

Jan 1, 1947

By Roswell P. Angier, Herbert S. Kalish, Henry H. Hausner

POWDER metallurgical methods as applied to zirconium are of great interest because they permit not only the fabrication of parts directly to shape with a minimum loss of material but also the utilization of scrap, and the metal may be processed at temperatures well below the melting point. There are two difficulties involved in the melting of zirconium: 1—High vacuum is necessary for melting, and 2—zirconium reduces nearly all oxides so that it is difficult to find a suitable crucible material. The purest material, zirconium crystal bar, is expensive, and the methods of subsequent fabrication are limited. Cold rolling or extrusion of zirconium crystal bar is suitable for making certain shaped parts, but where melting is involved, the purity of the metal is invariably decreased, and a method of casting to a definite shape does not seem to be feasible. Where it is necessary to hot roll, zirconium must be covered with a steel or copper jacket to protect it from the air. This is necessarily a costly operation. Where annealing of zirconium is necessary it must be conducted in a high vacuum. In an investigation of powder metallurgical methods for zirconium, the zirconium powder used should be characterized by the following properties: 1— Highest degree of purity, 2—uniformity in particle shape and particle size distribution, 3—low compression ratio, and 4—satisfactory strength of the compacted powder (green strength). Zirconium powders have been made by two methods: By the reduction of zirconium tetrachloride (ZrC1,) with sodium,2' *•B "nd by the reduction of zirconium oxide with calcium and calcium chloride." The first method represents one of the earliest attempts to make pure zirconium metal, and the sintered product from this powder is extremely brittle. The second method of making zirconium powder is far more successful, but the powder made in this way has an extremely low apparent density and, therefore, a high compression ratio which makes it difficult to use it for powder metallurgical purposes. For these reasons the above-mentioned zirconium powders were not used in this investigation. To obtain sintered zirconium compacts of highest 'purity and good ductility, it was first necessary to produce a suitable powder. Pure zirconium has been made chiefly by two methods. The iodide method, from which the product is "crystal bar" zirconium, was developed first.'." By this purification process very soft, pure, and ductile zirconium metal can be produced. The second method, developed by the U. S. Bureau of Mines, is the reduction of zirconium chloride with magnesium." The sponge zirconium thus produced is also soft, pure, and ductile.

Jan 1, 1952

By George B. Langford

The McIntyre mine is in the Pearl Lake section of the Porcupine gold area. The rocks are Keewatin lavas intruded by quartz porphyries and albitite dies of Algoman age. Gold-bearing quartz veins are found in the Keewatin rocks near the porphyry stocks. The whole area has been highly compressed by forces acting along a N. 20°W. line. These forces folded the Keewatin rocks before the intrusion of the Algoman rocks, and later schisted both the Keewatin and Algoman rocks. Vein fractures were developed after the folding but before the development of the schist by the compres-sive forces being locally broken up into couples. These couples were set up by the differential resistance to deformation of porphyries and basalts, and also by the competency of the dacites and incompetency of the tuffs and fragmental rocks. During the important period of vein formation, two zones were developed—an inner productive zone in which the quartz veins are ankerite-bearing and an outer barren zone in which the quartz veins are calcite-bearing. The vein solutions originated in the same magrna that supplied the albitite dikes. Introduction The McIntyre mine, in the Porcupine gold area of northern Ontario, has passed its twenty-sixth birthday and has been producing gold since early in 1912. During this time approximately ten million tons of ore has been mined and over three and a half million ounces of gold recovered. This amount of ore would be sufficient to fill 2300 standard railway freight trains, each of 100 cars, and the gold produced, although only equivalent to a cube 51/2 ft. to the side, would weigh approximately 100 tons, a load for three freight cars. Silver has been produced in the ratio of 1 oz. of silver to every 4.4 oz. of gold, so that the total silver recovery is in the neighborhood of 700,000 ounces. The early history of the mine, like that of many others, shows that for several years it fought an uphill struggle for existence. One of the important features in winning this fight was the early recognition of some of the geological conditions responsible for the ore deposits, and the application of this knowledge in the search for ore and in the acquiring of adjoining properties. As early as 1913—only two years after the mine was opened—a geological department was organiaed. It has functioned almost continuously since that date and has demonstrated the importance

Jan 1, 1941

By D. C. Hilty, W. Crafts

Determination of the solubility of oxygen in iron containing silicon, or manganese, or both, has confirmed the earlier work on silicon, shown that manganese is more effective than expected, and has demonstrated that the combination of silicon and manganese is a much stronger deoxidizer than might have been inferred from their individual effects. SILICON and manganese are of primary impor-tance in the deoxidation of steel, and a study has been made at the Union Carbide and Carbon Research Laboratories, Inc. of the solubility of oxygen in iron in the presence of silicon and manganese, singly and in combination, as a basis for more effective control of inclusion formation. The investigation was carried out with the same equipment and experimental procedure that were used in the determination of the oxygen solubility of iron containing aluminum'. The heats were melted in a rotating crucible furnace under an argon atmosphere. Bath temperatures were controlled by platinum/platinum +10 pct rhodium thermocouples to attain equilibrium at 1550°, 1600°, and 1650°C, so that oxygen solubility isotherms were determined directly without requiring calculation from a temperature coefficient. A detailed description of the furnace and procedure is given in the paper on aluminum deoxidation1. Oxygen solubility in the presence of more than 0.10 pct silicon was found to approximate earlier determinations closely, but some deviation was observed at lower silicon contents. Manganese appeared to be more effective than had been anticipated. The combination of silicon and manganese lowered the solubility for oxygen markedy as compared with either silicon or manganese alone. Although the solubility for oxygen in the presence of both silicon and manganese represents only a part of the information needed to control inclusion formation, it suggests a partial explanation of the benefits of this combination that have been observed in practice. Manganese and Oxygen in Liquid Iron: The study of oxygen in iron in the presence of manganese was carried out in magnesia crucibles of the type furnished commercially for laboratory induction furnaces. Alumina crucibles were unsatisfactory, because the work on the aluminum-oxygen equilibria in iron' had shown that merely melting iron in an alumina crucible limited the solubility of oxygen to a level considerably below that anticipated for moderate concentrations of manganese. Silica crucibles appeared unsuitable because of the dangers of excessive fluxing by the melt. Moreover, as will be shown later, melting iron in a silica crucible also limits the oxygen content below that in equilibrium with

Jan 1, 1951

By Edward Saibel

THE various theories that have been advanced to explain or predict the conditions under which a metal fractures may be divided into two categories: First, there are the macroscopic theories generally used in engineering practice. These are empirical in nature and limited in application. For example, the maximum normal stress criterion, which is quite satisfactory for a mild steel in simple tension at atmospheric pressure, no longer suffices when this steel is pulled under hydrostatic pressure.2 In all of these empirical theories, the critical condition characteristic of the material and of the loading conditions must be obtained experimentally. Secondly, there are the theories based on interatomic forces,3,4 or on the energy required to form new surface.5,6 These have all dealt with the theoretical evaluation of the tensile stress necessary to bring about rupture in a purely brittle manner; that is, without plastic flow preceding fracture. All of these attempts have led to values of the tensile strength of crystals or of polycrystalline bodies that are 100 to 1000 times higher than observed values. On this account, it has been thought necessary by some investigators to conceive of a microcrack structure or distribution of flaws throughout the specimen such that the resulting stress concentrations provide the factor necessary to bring about agreement between calculation and experiment. It has been pointed out by several observers7 that this point of view is highly unrealistic, in that the weakening effect of these flaws or microstructures must be very uniform from specimen to specimen, since the fracture stresses found for various specimens of the same material tested under similar conditions are so - nearly constant. Furthermore, since calculations based on atomic forces or atomic energy are for purely brittle fracture, a condition probably never satisfied in tests, agreement is hardly to be expected. Thermodynamic Theory Of Fürth In order to resolve this apparent discrepancy between the theoretical cohesive strengths and the observed fracture strengths, Fürth8 advanced a thermo- dynamic theory of the tensile strength of isotropic bodies based on work of Born9 relating to the melting of crystals. Assuming an isotropic material free from imperfections and flaws, behaving elastically up to the breaking point, and assuming a connection between rupture and the melt- ing phenomenon, Fürth obtains an expression for the rupture stress u, in the form [ ] where Q is the melting energy per unit mass, ? is the density, and µ is Poissons’ ratio. Fürth compares fracture stresses computed from Eq I with the fracture stresses of metals as given in the Landolt-Bernstein Tables (1927) and in the Hand-

Jan 1, 1947

By J. M. Hodge, H. M. Reichhold, R. D. Manning

The work reported in this paper represents the first of a series of investigations of the factors governing notch toughness in ferritic materials. This paper is concerned with two of these factors, namely, the effect of ferrite grain size, and the effect of an alloy content of 3.64 pct nickel. Every effort has been made to hold other variables constant in order to isolate the effects of these two. The compositions chosen for study were 0.02 pct carbon in order to eliminate the variable of carbide distribution, one steel being a plain carbon steel and the other alloyed with 3.64 pct nickel. Both steels were fully killed with silicon, without an aluminum addition, so that the variable of deoxidation practice was held constant. Finally, all samples were water quenched from 1200°F and tempered 24 hr at 300°F in order to hold the quench aging variable constant and to decrease the tendency for grain boundary carbide precipitation. The ferrite grain size was varied by heat treatment over the range of A.S.T.M. grain size numbers of about 2 to 6 in each steel so that the effect could be evaluated individually and the notch toughness of each steel could be compared at comparable ferrite grain sizes. Materials and Experimental Procedure MATERIALS The materials for this investigation were obtained from Battelle Memorial Institute as 250 Ib induction melts which were forged into 134 in. square bars and then rolled into 0.6 in. square bars. Both steels were deoxidized with silicon, the aluminum content being held to a minimum. Check analyses of these materials are shown in Table 1. HEAT TREATMENT FOR GRAIN SIZE The grain size was varied by varying both the cooling rate and the austeni- tizing temperatures. The heat treatments used and the corresponding grain size values are tabulated in Table 2. A semicontinuous network of grain boundary carbide was observed in the microstructure of both the plain carbon and nickel steels in the as rolled condition and an additional heat treatment was necessary to eliminate this variable. Therefore, all samples were water quenched from 1200°F and tempered 24 hr at 300°F as a final treatment before testing. This heat treatment served to eliminate to a great extent the grain boundary carbide network and to hold the quench aging effect constant. IMPACT TESTING Standard keyhole Charpy impact tests were machmed after heat treatment. A bath of acetone and dry ice was used for refrigeration of the samples down to temperatures of —94°F (—70°C) and a bath of either methyl-cyclohexane or isopentane, cooled by

Jan 1, 1950

By G. W. Healy, D. C. Hilty

MAJOR considerations in the production of stainless steel are the utilization of stainless steel scrap and the recovery of chromium and other metallic values from the initial furnace charge. The decarburization of a bath of molten chromium steel with gaseous oxygen is usually accompanied by a considerable amount of metallic oxidation. Since recovery of this metal from the slag may require substantial expenditures of time and materials for slag reduction, holding metallic oxidation to the minimum consistent with good operating practice is generally desirable. The important role of temperature in minimizing metallic oxidation is illustrated by Fig. 1, taken from the results of Hilty, Healy, and Crafts,' who established the quantitative relations connecting the amounts of chromium, manganese, and iron oxidized during the oxidizing period of chromium steel heats with the composition of the initial charge and the temperature and composition of the molten bath after oxidation. Higher temperatures after the oxygen blow result in lower metallic oxidation. Although high temperatures are desirable for minimizing metallic oxidation, practical operating considerations limit the degree to which they can be employed. Excessively high temperatures or prolonged operation at moderately high temperatures may cause serious damage to the furnace refractories, so that a compromise must be effected. The problem, therefore, is one of controlling the oxidizing period of chromium steel heats to the shortest time at the highest practical temperature. The most effective tool the steel melter has for attaining high temperature while decarburizing a chromium steel heat is now commonly considered to be the oxygen lance with an adequate supply of gaseous oxygen. In order for the tool to be effective, however, the heat resulting from the oxidation of carbon, chromium, silicon, manganese, and iron in the bath must exceed the heat losses from the furnace. General recognition, of this principle has stimulated a trend toward faster injection of oxygen. For example, Pachaly2 proposed a high temperature at the start of the oxygen blow or a high rate of oxygen input as a means of obtaining the desired carbon level with high chromium recovery. On the other hand, limited understanding of the specific effects of oxygen input rate has hampered development of optimum practices. As part of a broad study of the metallurgy of chromium steel melting, therefore, the Linde Air Products Co. and the Electro Metallurgical Co. at their Metals Research Labo-ratories have evaluated the heat-balance during the oxidizing period in terms of oxygen input rate. The evaluation has then been related to factors such as temperature increase, metallic oxidation, oxygen Utilization, etc., and extrapolated to include a wide

Jan 1, 1958

By F. C. Blickensderfer

THE CHAIRMAN (B. B. GOTTSBERGER, Miami, Ariz.).-On your trip today through the Inspiration and Miami mills you have seen in actual operation the machines which represent the changes adopted in grinding methods in the Miami district from the beginning of operations in March, 1911. In one section of the Miami plant are three Chilean mills not yet discarded, representing the first machines adopted. In another section, pebble grinding is still in operation, while in the balance of the plant, pebbles have been replaced with iron balls. In all cases these machines are handling a feed which is the product of roll, grinding down to about ¼ in. in, size. The latest step in grinding in the district, You saw at the Inspiration plant, where in Marcy mills a filed, the larger pieces of which remain on a 2-in. opening, is being reduced in one operation to a product of which only about 3 per. cent. remains on the 48-mesh screen. A detailed comparison of the methods used at the two plants would be very instructive but our own work at Miami has not yet reached a point where such a comparison is possible, the reason being that our final product is not yet fine enough. By means of larger Hardinge mills operating in closed circuit with Dorr classifiers soon to, be installed in one section of the plant, we hope to obtain, under properly balanced operating conditions the same end result as at Inspiration. It, might interest you, however, to know some of the results we have obtained here by the substitution of balls for pebbles. With pebble grinding, using three 8-ft. by 22-in. mills, followed by one 8-ft. by 66-in. mill for regrinding the coarse product of the primary mills, we handled 636 tons per 24 hr. in one section of the plant. Substituting balls for pebbles in the first operation and using two mills in place of three we obtained a tonnage of .714 tons to the section. With the use of balls both in the primary mills and in the regrinding mills, the tonnage for one section was raised to 822 tons per day. Coincident with this increase in tonnage, we also obtained a greater efficiency. The use of pebbles in all mills showed 21.5 per cent. plus 48-mesh material in the final tailing, which figure was reduced to 13.9 per cent. for balls followed by pebbles, and to 4.6 per cent. with the use of balls both in the primary and regrinding mills.

Jan 12, 1916

By L. W. Davies

A problem often encountered is the provision of materials which have impurity contents below a certain specified level. This problem is in some cases solved by making use of the segregation of the impurity with respect to the liquid and solid states of the material: an ingot of the material is subjected to directional solidification and the ends of the ingot. which are richer in solutes which respectively raise and lower the melting point of the solvent, are removed. An important extension of this process is the zone-refining process invented by pfann,' in which molten zones are passed successively along the length of an ingot and displace solutes towards the ends. Pfann's process is particularly appropriate in cases for which the segregation coefficient k does not differ greatly from unity, or when the impurity content must be kept extremely low (-=,6 atom fraction); it is widely used, particularly in the purification of materials for use in semiconductor electronic devices. It is the purpose of this paper to investigate theoretically the efficiency of the above refining processes; that is! we determine the most economic method of attaining a given yield of solvent of specified purity, taking into account the variables of the process. One variable of interest is the effective value of the segregation coefficient. which depends on the rate of movement of the liquid-solid interface and on the degree of stirring in the liquid; in addition to this, in the zone-refining process we are also interested in the choice of zone length for most efficient operation. A mathematical determination is made here of the lengths of successive molten zones which give, for an initially uniform distribution, the most efficient removal of a solute of arbitrary distribution coefficient. In order to be able to give a quantitative treatment of efficiency, we first define figures of merit applicable to a given distribution of solute. FIGURE OF MERIT Let an ingot of length L contain a distribution y(x) of solute: we confine our discussion to mono-tonic distributions, in order to avoid inconsistencies in the subsequent analysis. The first moments of the distribution about the origin and x = L are respectively L F = hy{x)dx [I] G = f(L -x)y(x)dx = YoL2-F, [21 where yoL is the total amount of solute present. We shall see that the quantities F and G are useful figures of merit for a discussion of the efficiency of zone-refining processes. In the first place, it is

Jan 1, 1960

By L. W. Davies

A problem often encountered is the provision of materials which have impurity contents below a certain specified level. This problem is in some cases solved by making use of the segregation of the impurity with respect to the liquid and solid states of the material: an ingot of the material is subjected to directional solidification and the ends of the ingot. which are richer in solutes which respectively raise and lower the melting point of the solvent, are removed. An important extension of this process is the zone-refining process invented by Pfann,' in which molten zones are passed successively along the length of an ingot and displace solutes towards the ends. Pfann's process is particularly appropriate in cases for which the segregation coefficient k does not differ greatly from unity, or when the impurity content must be kept extremely low (=10-6 atom fraction); it is widely used, particularly in the purification of materials for use in semiconductor electronic devices. It is the purpose of this paper to investigate theoretically the efficiency of the above refining processes; that is! we determine the most economic method of attaining a given yield of solvent of specified purity, taking into account the variables of the process. One variable of interest is the effective value of the segregation coefficient. which depends on the rate of movement of the liquid-solid interface and on the degree of stirring in the liquid; in addition to this, in the zone-refining process we are also interested in the choice of zone length for most efficient operation. A mathematical determination is made here of the lengths of successive molten zones which give, for an initially uniform distribution, the most efficient removal of a solute of arbitrary distribution coefficient. In order to be able to give a quantitative treatment of efficiency, we first define figures of merit applicable to a given distribution of solute. FIGURE OF MERIT Let an ingot of length L contain a distribution y(x) of solute: we confine our discussion to mono-tonic distributions, in order to avoid inconsistencies in the subsequent analysis. The first moments of the distribution about the origin and x = L are respectively L F = hy{x)dx [I] G = f(L -x)y(x)dx = YoL2-F, [21 where yoL is the total amount of solute present. We shall see that the quantities F and G are useful figures of merit for a discussion of the efficiency of zone-refining processes. In the first place, it is

Jan 1, 1960

By J. L. Swedlow, M. L. Williams

Two standard techniques for assessing fracture initiatlon in sheet specimens involve measurements of 1) the applied load of fracture which, via linear fuacture mechanics, is used to find the fracture tough/less SC (or SIC), and 2) the velative displacement of fracture of the opposite free faces of the crack (COD). In the past, the quantitative association between these two parameters has not been determined in detail, owing to the mathematical difficulties of computing. the stress and strain fields in the combined elasto-plastic flow near the crack. Using a numerical technique Irecently developed and applied to a 7075- TO' aluminum plane stress specimern, the two parameters noted have been determined and associated quantitatirely. CONSIDERABLE effort has been expended in selecting a rigorous yet practical manner for predicting fracture. The usual point of departure is the modified Griffith criterion in which the mechanism of energy dissipation is reflected in Sc (or SIC), the parameter of "fracture toughness". Sc. differs from the surface energy used by Griffith in perfectly brittle fracture in that it includes the effect of plastic flow in the vicinity of the crack tip. Because plastic flow alters the stresses and displacements predicted from the usual linear theory of fracture mechanics, and because analysis of the nonlinear stress-strain field has presented great obstacles: only estimates of several pertinent quantities have heretofore been available. Nevertheless, two parameters have often been measured experimentally althougll usually just at the point of fracture. These are the energy release rate, or fracture toughness 9, (or I,), and the crack-opening displacement (COD). Such observations have been used in connection with frarture criteria and have been most helpful in design, although their application requires care with respect to changes in geometrical configuration from that upon which the criteria were based 1,2 Recently, however, a reasonably accurate and comprehensive method for analyzing the elasto-plastic flow has been devised and applied to plane stress specimens having arbitrary octahedral stress-strain curves.3 It thus becomes feasible to compute, albeit numerically, both the fracture toughness and crack opening as functions of the applied tensile loading on a typical specimen geometry. As a result, it is now possible to associate these two parameters quantitatively, and thereby to associate data obtained by one method with data pertaining to the other. ELASTIC ANALYSIS For the case of linear elasticity, it is relatively easy to deduce the connection between various measures of crack deformation. Using, for example, the singularity analysis, it is found that the leading term of the Airy stress function x f°r symmetrically applied loadings on an isotropic medium is

Jan 1, 1968

By George H. Found

DURING recent years considerable interest has been focused on the energy-absorption characteristics of metal when it is cyclically stressed in vibration. The most familiar manifestation of this phenomenon, which is called the "damping capacity" or "internal friction" of a material, is involved in the dissipation of mechanical energy of vibration, which otherwise would build up to stress levels where the problems of noise and fatigue are involved. In addition to its engineering importance in structures, the damping behavior of metals, particularly at low stress amplitudes, has also been used as a unique metallurgical research tool with which to provide sensitive means for indicating certain structural changes within metals. Important contributions toward understanding the energy-dissipating mechanisms that are responsible for internal friction in metals have been made in the last few years. The information is not yet sufficiently extensive, however, to provide a useful metallurgical concept describing exactly how the structure affects the internal friction, or to encourage more general use of this technique among metallurgists. Three fundamental mechanisms have been proposed, as a result of recent experimental investigations, to account for the internal friction in nonferrous metals in low-stress amplitude tests. These include damping due to internal thermal currents that are created and flow in metal because of differential vibratory stress effects,1 damping due to localized inelastic stress relaxation at inhomogeneities within the metal,2,3 and damping related to plastic flow of a localized type for which an explanation has been sought in terms of the dislocation theory.4 How each of these mechanisms functions as a result of structural changes in the metal is, in general, not well understood because of insufficient experimental data for which the controlling variables have been segregated and because of uncertainties in regard to the nature of the structural changes themselves. In several investigations the effects of cold-working on the internal friction of polycrystalline brass and aluminum have been described. As reported by Köster and Rosenthal,5 and by Förster and Breitfield,6 there is an initial large increase in the damping when the metal is worked. The initial high value is not stable, but declines rapidly, at first, in a hyperbolic manner. About 100 hr, after straining, a stable value is reached of magnitude proportional to the amount of strain.7 In Fig. I is shown the relationship found by Zener and his collaborators between the internal friction due to cold-working of alpha brass and the amount of cold-working.8 Several investigators have made internal-friction measurements on worked poly-

Jan 1, 1945

By C. G. Dunn

WITH respect to theories of recrystallization in metals plastically deformed, it has been said that the present status of this subject is far from satisfactory.1 It may also be said that before any mechanism of recrystallization for metals and alloys can be set forth in a satisfactory manner, there must be made available considerable data on orientation changes that occur during the deformation and recrystallization processes. Although extensive data have been published on recrystallization in single crystals and in polycrystalline specimens, more results of a type that can be classified according to simple orientation changes would be desirable in this complex field. It might even be said that before classifications are made according to types of orientation changes, it may be possible to classify a considerable amount of data into certain kinds of orientation states if groups of common or nearly common orientation occur. Methods for computing the probability of occurrence for various types of groups have been published2 and it has been pointed out in particular that it should be possible to analyze orientation data for high-order twin relationships between old and new grains even when agreement is not at all exact. In this connection, work on recrystallization in silicon ferrite reported in a paper concerned with complex groups of annealing twins' indicated that some data were consistent with primary nucleation occurring according to a second-order or a third-order twin transformation. However, further work in this latter direction was definitely needed. It is, therefore, the purpose of the present paper to report data and analyses for primary nucleation in silicon ferrite following small deformations that have been carried out at the Pittsfield Works' Laboratory of the General Electric Co. Analyses have been made with the aid of standard groups of twins that are reported elsewhere .4 PREPARATION OF SPECIMENS AND EXPERIMENTAL PROCEDURE The material used in the present investigation was taken' from the same heat of steel as that used in a prior report.3 The finished strip in both cases was made by the Allegheny-Ludlum Steel Corporation according to methods that produce a high degree of preferred crystal orientation. Samples with large grains had the following composition: 3.45 per cent Si, 0.003 C, 0.008 P, 0.020 S, 0.075 Mn, 0.031 Al and 0.072 Cu. Thickness of specimens was 0.012 inches. Plastic deformation was produced by cold-rolling the samples on a mill with

Jan 1, 1945

By Irving B. Cadoff, Stojan M. Zalar

AgInTe2, CuInTe2, and all Proportions of CuxAg1-xInTe, forMed homogeneous single phase alloys after direct solidification from the nielt. X-ray analysis indicated a zinc-blel~de strzccture typical of the chalcopyrite compounds, and the electrical resistivity and Sccbeck coefficient values were in the semiconducting range. AuInTe, and AuxA4g,-, InTe, formed by what appeared to be a peritectic reaction (the thermal analysis curves showing more than one arrest) and were conseyue~ztly polyphase. Substitution of copper into AgIrzTe, resulted in a continuous transition in the room tenzperature Seebeck coefficient from the negative AgIzTe, to the positive CuInTe,. A zero coefficient was obtained at about Cuo.55 Ago.45 InTe, . The temperatzire variation was similar to that observed for the stoichiometric compounds, that zs, tendency towards "p" concEuction at elevated temperatures. The thernzoelectric figure of merit for the compo~uzds, as determined by the Putley -Harmnn method were in the range 10- to 10-7 "K-l; the thermal conductivities in the order of 0.15 cal per sec-cm-oK. INCREASED interest in semiconducting intermetallic substances is expanding much of recent research from simple binary compounds into polyatomic systems and solid solutions. Ternary compounds A' represent a covalent extension of the binary semiconductors Within the a tin isoelec-tronic series, Ag-Cd-In-Sn-Sb-Te-I, divalent cadmium atoms in CdTe are being substituted for by monovalent silver and trivalent indium atoms to form the compound AgInTe, . By cross-substitution with elements of other isoelectronic series, a great number of ternary compounds A 'B"'c? is possible. In all of them, however, a necessary though not sufficient condition for the covalent, semiconducting bond—that there be four sharing orbital electrons per atom—must be fulfilled. In AgInTe,, each silver or indium atom is tetrahedrally surrounded by four tellurium atoms, while each tellurium atom is co-valently bound to two silver and two indium atoms. Synthetic chalcopyrites A'B"'c~ were first recognized as potential semiconduct&rs by Goodman and Douglas.' Austin, Goodman, and Pengelly discuss preparation difficulties and some electronic measurements on AgInS, , AgInSe, CuInSe, , AgInTe, , and CuInTe,. Chalcopyrites A B c2v are mentioned in papers attempting to classify and predict semiconducting behavior of intermetallic compounds; on the basis of saturated tetrahedral sp3 bonds,3 by specific selection criteria,' and by crystallographic considerations."

Jan 1, 1962