Search Documents

By James J. Halbouty, Michel T. Halbouty

Drilling activity in the South Texas area, which includes the South Corpus Christi and Laredo districts, showed a marked decline during 1941 from that of the preceding year. The rate of new discoveries, however, 'compared favorably with exploratory results of 1940 because of the many new productive sands opened in existing fields. South Texas completions for 1941 were about 12.3 per cent below the 1940 figure, compared with an increase of approximately 5.5 per cent in the total number of completions in the United States during 1941 over the 1940 total. During the year, 1452 wells were drilled in this area; of these, 1205 were drilled in or as extensions to the proven fields, and 247 were rank wildcats drilled in search of new producing pools. The comparable 1940 figures were: 1320 field or extension wells and 336 rank wildcats, a total of 1656 completions. This represents a decline in 1941 of approximately 8.7 per cent in proven-area wells, and of about 26.5 per cent in rank wildcats. It must be stressed that wells that were considered rank wildcats at the beginning of operations, but which opened production later classified as additions to existing fields, are not regarded as rank wildcats in this and previous annual reports on this same area. These wells are classified as semiwildcats (Table 2). There were 13 new oil or distillate fields and 4 new gas areas opened during the year, as listed in the next column. This listing represents a decline of 32 per cent from the 25 new areas found during the previous year, and to a great extent can be attributed to the 26.5 per cent decline in wildcatting. The rate of new discoveries based on the 247 wildcats was 14.5 to I, which compares somewhat unfavorably with the 13.4 to I ratio obtained in 1940 (Table 5). Dry wildcats totaled 230. The proof of the prolific character of the South Texas area as a source of petroleum reservoirs is to be found in the fact that of the 1205 field or extension (semiwildcat) wells completed during the past year 61 opened production from new sands or found crude in formerly distillate-producing sands. The 1940 total of 1320 such wells accounted for 50 horizons that provided either new production or crude in distillate sands, and in this respect the 1941 rate of discovery shows to greater advantage, the ratios for new sands being 19.7 to I for 1941 and 26.4 to I for 1940. The 1205 field or semiwildcat wells completed in 1941 resulted in 926 oil or dis-

Jan 1, 1942

CONTENTS PAGE BARTON, D. C.-The Eötvös Torsion Balance Method of mapping Geologic Structure (T. P. No. 50) 1 GEORGE, P. W.-Experiments with Eötvös Torsion Balance in the Tri-State Zinc and Lead District (T. P. No. 65). 15 LANCASTER-JONES, E.-The Computation of Eötvös Gravity Effects (T. P. No.75) HEILAND, C. A.-A Cartographic Correction for the Eötvös Torsion Balance-(T. P. No. 52) 17 SLICHTER; L. B.-Certain Aspects of Magnetic Surveying (T. P. No. 120). . . . 18 WEAVER, W.-Certain Applications of the Surface Potential Method (T. P. No.121) LUNDBERG, H.-Recent Results in Electrical Prospecting for Ore (T. P. No. 98). . 20 HOTCHKISS, W. 0., ROONEY, W. J. and FISHER, J.-Earth-resistivity Measure-ments in the Lake Superior Copper Country (T. P. No. 82) 21 LEONARDON, E. G. and KELLY, S. F.-Some Applications of Potential Methods to Structural Studies (T. P. No. 115) 23 MASON, M.-Geophysical Exploration for Ores (T. P. No. 45) 25 The Eötvös. Torsion Balance Method of Mapping Geologic Structure Discussion of the paper of D. C.. Barton, issued as Technical Publication No. 50 with Mining and, Metallurgy, February, 1928. D. C. BARTON.-The field surveys which I have been privileged to use as illustrations for this paper were done for Mr. DeGolyer's companies and were released through his favor. W. J. MILLARD, Tulsa, Okla.-Has any oil been found by the torsion balance in West Texas? D. C. BARTON.-NO new oilfield has been discovered on the basis of torsion balance work. It has had some part in controlling the policy of certain companies in playing the extension of known oil fields. A number of "T. B." structures have been drilled and dry holes obtained. Of those known to the writer, one apparently was a structural high, one is a broad general high but locally low and probably is a deep-seated structural high, one seems normal although the control is poor, and one was considered structurally low but is now suspected by some geologists of being structurally high. E. L. DEGOLYER, New York, N. Y.-A large gravity structure, generally referred to, I believe, as the Crosby County Structure, has been found in West Texas. This structure is perfectly symmetrical with the arrows all pointing toward a common center, very much like the Nash salt-dome pattern in Dr. Barton's paper (Fig. 9). One of the peculiar things about it, from the standpoint of the gravity high, is that it is so

Jan 1, 1928

By G. M. Ault, G. C. Deutsch

The paper reviews the efforts made to utilize powder metallurgy to solve problems encountered when using alloys at high temperatures. The following subjects are discussed: comparison of wrought and sintered super alloys, sintered aluminum powder, porous materials for transpiration cooling, molybdenum, and cermets. TODAY, powder-metallurgy techniques are be-JL coming increasingly important, producing materials which at the present time cannot be made by any other method. Among these materials are high melting-point metals such as tantalum and tungsten, porous metals for filters and lubricant-containing bearings, electrical contacts and electrodes (i.e., tungsten-copper), cutting tools of the cemented carbides, and magnet alloys. In addition, the powder-metallurgy industry has grown because, through the application of its methods, shaped parts, such as gears, can be produced at tremendous rates with a low scrap loss in comparison with manufacture by casting or forging and machining. In the past few years, by utilizing powder metallurgy, several approaches to the problem of high temperature materials have been investigated. In this paper the authors will review some of the studies on application of materials having properties above 1350°F. Since their experience lies in the aeronautical field, possible uses of powder-metallurgy techniques in the production of aircraft en- gines will be emphasized. A large portion of the work is classified, but such a restriction has not eliminated any field from discussion, although limiting the amount of detail it is possible to present. The development of high temperature alloys from powders and porous metals for cooling will be discussed as well as research done on molybdenum and molybdenum alloys, cermets, and intermetallics. Some studies on the utilization of cermets will be considered along with special problems that have been revealed through these investigations. Special interest in certain factors of sintered aluminum powder (SAP) makes it desirable to discuss this material although its use temperature is below the 1350°F limitation set for this paper. High Temperature Alloys from Powders In general, components made from powders for room-temperature application have been investigated with the primary purpose of taking advantage of the high production rates and economies made possible by powder metallurgy. From the standpoint of properties, the ojective of the powder metallurgist has been to obtain a product comparable to the cast or wrought product that is to be replaced. Comparisons of the properties of alloys made by powder-metallurgy methods with those of similar compositions made by casting and forging are reported in the literature.12 In many cases equivalent

Jan 1, 1955

By Arnulf Muan, R. E. Johnson

Equilibrium CO2 /CO ratios of a gas phase coexisting with selected oxide phase assemblages of the system CaO-"Fe0"-SiOz and vnetallic iron have been determined at 1080°C. The data obtained are used to calculate activity-conzposition relations for metasili-cute, orthosilicate, and CaO- "FeO" solid solutions, and to determine a new value for the free energy of formation of C&S&0,. The metasilicate solution is practically ideal, whereas large deviations from ideality exist in the othe,r two solid solutions. BECAUSE of the geochemical and metallurgical importance of the oxides CaO, "FeO", and SiOz, the system CaO-"FeO"-SiO2 has been the subject of several experimental studies during the past 30 years. Following the delineation of phase relations at liquidus temperatures by a group of investigators at the Geophysical Laboratory of the Carnegie Institution of Washington in 1933,1 Chipman and associates in the early forties2,3 determined activities of FeO in liquids of this system. Since that time, many attempts have been made to interpret the data of Chipman et al. in terms of the constitution of the silicate liquids and the interaction parameters among the various constituents of the system (see for instance papers by Richardson4 and by Flood and coworkers5). One of the assumptions made in some of these interpretations4 is that the binary silicate systems CaSiO3-FeSiO3 and CazSi04-Fe2SiO4 mix ideally in the solid state. The objective of the present study is to provide experimental data on activity-com position relations in solid solutions of the system CaO-"FeO"-SiO2. Such data will contribute toward an understanding of the thermodynamics of silicate solid-solution phases in general, and will serve specifically to confirm or refute some of the assumptions made in interpreting liquid slag behavior. PREVIOUS WORK Phase relations in the system CaO-"FeO"-SiO2 in contact with metallic iron were determined by Bowen, Schairer, and Posnjak,1 and additional phase-equilibrium data for this system have been presented by Allen and snow.' A reproduction of the most up-to-date phase diagram for this system is shown in Fig. 1.7'8 Of particular interest in the present investigation are the relations among the various crystalline phases slightly below the lowest solidus temperature in the system, as shown in Fig. 2. The present work will be concerned primarily with some of the composition

Jan 1, 1968

By T. R. Graham, J. R. Long

This report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau's War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. Preliminary Work In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, o to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944

By P. W. Andrews, R. B. Toombs

ECONOMIC STRUCTURE OF MODERN INDUSTRIAL ECONOMIES The role of minerals in modern industrial economies may be examined in several ways. There are relationships with the various sectors of the economy: the primary, secondary, and tertiary industrial groupings and activities. Mineral supply and demand activities can be measured in terms of national accounts criteria. The economic policy objectives of the modem industrial economy are based to a considerable extent on the needs of the nation for economic supplies of miner- al materials. There is an important role for minerals relative to national security in peace and in wartime and many national policies are directed toward ensuring adequate sup- plies of minerals. Environmental control in the modem industrial economy is increasingly concerned with matters related directly to the production and use of minerals and these matters, in turn, bear importantly on conservation in mineral supply and demand. Mineral polices include specific provision for research and development activities concerned with the production and the use of minerals. In all, national policy objectives will be shaped in considerable part by the circum- stances of mineral supply and demand: the relative degree of availability from domestic and foreign sources, the state of the mineral-processing industries, and the degree of development of the mineral-using industries, and per capita and total changes in requirements. Goods made from mineral raw materials are the basis of all advanced societies and although this is taken for granted, every country is continually dealing with problems of mineral supply and demand. Considering that in the first 50 years of this century the consumption of mineral materials in a highly Industrialized country such as the United States increased by six times while the population was doubling, it becomes apparent that if a country is to enjoy rapid economic growth it must have access to huge and ever-growing supplies of mineral materials at lowest possible cost. Adequate supplies of mineral materials and wise usage of mineral resources have always been among the most important determents of a nation's survival The importance of access to adequate mineral supplies is increasing every year and this has significant international, as well as national, implications because of the unique locational characteristics of mineral resources. It is generally acknowledged that no particular type of natural resource is essential to a high level of national income or to economic progress. A country's endowment of natural resources need not exercise a determining influence on the course of its national income over time, provided it is able to trade. What is required for economic progress is the availability of a substantial quanti-

Jan 1, 1976

By Kenneth K. Humphreys

INTRODUCTION What is automation? Why automate? Webster's New Collegiate Dictionary defines automation as "the automatically controlled operation of an apparatus, process or system by mechanical or electronic devices that take the place of human organs of observation, effort, and decision." This definition gives an implied answer to the second question, )"Why automate?" Automation, automatic control devices and process control equipment receive their justification in supplementing or replacing manpower, which results in decreased operating costs. In the past, processes were operated with a minimum of instruments for the purpose of merely guiding the operators. Processes were manually controlled by the operator on the basis of simple temperature, pressure, flow and level indications on a panel. Today the tendency is to design a new plant to operate in a fully automatic manner according to a preset pro- gram utilizing a minimum of manpower. In addition to this direct cost reduction savings in manual labor, increased equipment capacity results from uniformity of flow and uniform control of process variables. This control eliminates or minimizes surges and permits equipment to be operated at or near its ultimate capacity and, for a given material through- put, permits the use of smaller process equipment. Automatic control, therefore, be it in the field of coal processing or in any industrial field, is simply a problem of economics. Control equipment is justified in terms of its contribution toward increasing productivity, increasing profit margins or producing a new and saleable product at a profit. Instruments and control devices can be divided into two general groups: (1) units which measure, and (2) units which both measure and control a process variable. In coal processing, the first class of instruments, those which measure only, include analytical devices such as automatic ash, moisture and sulfur measuring units and the simple pressure, temperature, flow and level indicating devices mentioned previously. The second group of instruments, those which both measure and control, include a wide variety of units such as continuous weighing devices on conveyor belts and photoelectric cells which gauge the position of railroad cars on the track and insure that the cars are in the proper location for loading (see Chapter 15). The latter types of units as used in the coal industry differ from those used in other industries in one significant point. In coal processing these instruments need not be as highly sophisticated and accurate as in other industries; hence their cost is proportionately lower than in other industries. Because of the economic fact that coal sells for only a fraction of a cent per pound compared to dollars per pound for many chemical products, and

Jan 1, 1968

By J. R. Long, T. R. Graham

This report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau's War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. Preliminary Work In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, o to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944

By Samuel Daniels

The Al-Cu-Ni-Mg alloy is much benefited by heat treatment and, in such condition, is preferable to the Al-Cu-Fe-Mg alloy either as cast or as heat-treated, when both are reheated to temperatures of from 400" to 600" F. and compared, cold, with respect to strength and to hardness. The main differences between the alloys do not arise until the reheating temperature exceeds 400" F., above which they gradually soften. This softening is characterized metallographically by the appearance of intragranular precipitate. The Al-Cu-Ni-Mg alloy is weakest and least hard after being reheated at 600" F., the Al-Cu-Fe-Mg alloy at about 700" F. The former starts to reharden at 700" F., the latter at 800' F. There is a tendency for both alloys to lose strength and hardness with prolongation of time at the reheating temperatures of 500" and of 700" F. The Al-Cu-Ni-Mg alloy is considerably stronger and harder than the Al-Cu-Fe-Mg alloy when both are heat-treated and reheated for long periods of time at 500" and 700" F. Although the latter can be made harder initially than the Al-Cu-Ni-Mg alloy by suitable quenching and aging, heat treatment, in general, favors the retention of this initial (strength and) hardness after reheating to a much greater degree in the Al-Cu-Ni-Mg alloy. The percentage of elongation of the two materials in any condition is very small. Certain aluminum alloys have been used for pistons and other parts operating at temperatures up to 650" F. because of their lightness, high thermal conductivity and specific heat, fair strength and hardness at elevated temperatures, excellent machineability, and moderate resistance to corrosion. In the piston, the inertia forces and the bearing loading, and with this the vibration, are decreased. The piston head functions at a lower temperature (about 200" F. below one of cast iron), so that, because of the lessened tendency toward carbonization and detonation, higher compression ratios may be used. On the other hand, the aluminum alloys do not have the wearing and bearing qualities of cast iron; also they have a large coefficient of expansion, allowance for which must be made in the design. The range in analyses of aluminum alloys, used for pistons in domestic and in foreign internal-combustion engines is shown in Table 1. There seem to be three general types of composition; one containing about 10

Jan 1, 1926

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550'F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550'F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

By Malcolm F. Hawkes

AUSTENITE grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, machinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to provide knowledge of the grain-size -characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstructures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The problem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will be considered first. More than So commercially produced cast steels representing a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules; namely, one hour at 1550°F, one hour at 1700°F, and six hours at 1700°F. The list of steels and results obtained on them will be found in the appendix. (See page 21.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT METHODS SUITABLE FOR DETERMINING AUSTENITE GRAIN SIZE AFTER HEAT- TREATMENT AT ORDINARY TEMPERATURES AND TIMES It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1947

By Hubert E. Risser

Although, for about a half-century the percentage of coal production provided through strip mining has steadily increased, recent trends indicate that a peak in percentage (not tonnage) is being approached, principally because of the decline in economic adrantage enjoyed by strip mining compared to underground mining. Factors contributing to the decline are the decrease in the margin of advantage in manpower requirements held by strip mining; an increase in depth and volume of overhurden, requiring larger equipment and capital investment; increasing lack of reserve land blocks large enough to support extensive strip mining operations; more stringent legislation for reclamation of stripped land, with increasingly higher costs of such reclamation; and the increasing costs of land surface rights for strip mining. Already there has been a peak and suhsequent decline in relative importance of strip mining insome major Eastern coal-producing states; trends indicate that a peaking for the whole Eastern region is on the way. Although, in the West the pressures are less severe, they will, nevertheless, reduce to an increasing degree the advantage that strip mining has possessed. For about half a century, strip mining has been providing an ever-increasing share of total coal output in the United States, and in the past 30 years this share has grown from less than 8% to 33.7%, as shown in Fig. 1. Fig. 1 also shows that strip mining is gaining faster in the West than in the East. From 1961 to 1967, output from strip mines grew 63.6 million toqs, or 52.2%. Certainly there is nothing in such performance to indicate any peaking in the level of strip coal-mine production. But the fact is that, if not in actual tonnage, strip mining appears to be reaching its peak in relative importance, at least east of the Mississippi River. And the area east of the Mississippi provides 90.0% of the strip and 94.9% of the total coal production of the nation. The relative economic advantage which spurred strip mining's growth for a third of a century has been diminishing markedly in recent years. Fig. 2 shows evidence of this decline. From 1947 until 1961, strip tonnage output remained fairly stable, at the end of the period showing only a 12.5% decline. Meanwhile, underground coal production fell 44.5%. As the result of the greater decline in underground coal, strip coal in 1961 furnished 30.3% of the total coal produced, compared to only 22.1% in 1947. In the succeeding six years, however, underground coal output increased by 76.5 million tons, while strip output increased only 63.6 million. Further evidence of the strengthening of underground coal's relative position — or if you will, the weakening of strip coal's position — can be found in the major coal stripping states: Illinois, West Kentucky, Ohio, Pennsylvania, Indiana, and West Virginia, which in 1966 provided 80% of the nation's strip coal. Fig. 3 shows what has been happening in three states lying in the Appalachian field and in the total output of these three states. In the figure, the column height represents the output of coal mined by all methods. The number at the base of each column is the percentage mined by stripping. In Pennsylvania and Ohio, the percentage of strip mining increased between 1956 and 1961, but by 1966 had declined from the 1961 level. In West Virginia, a decline occurred during the first five years but was followed by a rise. In January 1968, Coal Age published an article listing the locations and capacities of new large mines in the planning and construction stages that would be operating by 1968-1971. The plans for West Virginia and Pennsylvania indicated all the new mines would be underground. Except to the extent they might replace existing under-

Jan 1, 1970

By W. L. Saunders

(New Haven Meeting, February, 1909.) This paper deals specifically with heading-driving as distinguished from the broader term tunnel-driving. A heading is a pilot or path-finder for the main tunnel. Some headings are complete tunnels in themselves; that is, conditions at times warrant driving a heading the full diameter of the proposed tunnel. A tunnel 10 ft. in diameter might be driven to advantage through a single heading, provided the nature of the material admits, but it usually pays to drive rock tunnels of large diameter through the heading-and-bench system. Much de-pends upon the material, as in soft ground tunnels of much larger diameter are driven in a single heading. In mines, the tunnels, drifts, cross-cuts, adits, etc., are usually of small diameter, hence the driving of headings applies to completed tunnels in minim-work, except, of course, in cases like drainage-tunnels and main entries leading into coal-mines, where conditions call for tunnels of large diameter, approximating those driven for railway-service. In building aqueducts the tunnels are driven from 6 to 8 ft. in diameter up to 15 or 20 ft., while in railway-service the dimensions vary from 18 to 30 ft. in diameter. There is no department of rock-excavation so difficult as that of heading-driving. This work. also belongs to the most expensive class in rock-excavation. A heading is driven .directly in the solid. There are no lines of lesser resistance towards which to direct the energy of the blast, but. the material must be blown out by main force. The completion of the heading simplifies all the rest of the work of excavation. It is easy, for instance, to enlarge a heading either from above, below or oil the sides, by breaking towards the open face through holes approximately at right angles to the axis of the heading; or the enlargement sometimes takes place by holes driven outside

Apr 1, 1909

By G. F. Loughlin

Nearly 55 years have elapsed since the U. S. Geological Survey was organized. During this period the mineral industries have grown from infancy or early childhood to well developed maturity, and some mining industries appear to be declining. Decline in mining is even more conspicuous in certain districts, or even states, than in any mining industry as a whole, and discoveries or developments of important new districts have been very few in recent years. Our reserves of most metals and nonmetals are adequate for many years of normal production, subject to changes in rate of exploitation that may be caused by foreign competition and by changes in technology and market conditions; but the declining production of many districts and the scarcity of important new discoveries to compensate for them is cause for some apprehension. It is likely that future production will depend to a considerable extent on deep exploration and on the thorough examination of places in and adjoining existing districts where significant outcrops are lacking and only apparently insignificant geologic features offer encouraging clues—more so than on the discovery of entirely new districts. Even the possible discovery of new districts, which have escaped the intensive search by the nontechnical prospector, must be dependent on geologic information. There is therefore no need for argument as to the value of geology to the mining industry; and the need of continuing to advance the science. The U. S. Geological Survey's past contributions to mining geology, as expressed in its official reports and other publications, are recognized by Ransome in his historical review of mining geology in the Lindgren volume.' These contributions have helped to form the basis of modern mining geology, which has grown rapidly in the last 25 years. This growth has witnessed the organization and maintenance of geologic staffs by mining companies in several districts, and their detailed work, together with the fact that nearly all of the larger mining districts have

Jan 1, 1935

By George W. Riter

(Canal zone meeting, November, 1910.) A DISTINGUISHED engineer, the active head of a large mining company, has said that surveying attains the dignity of a profession only in the hands of a few men-the few who know how to keep notes that will be understood by even a novice without further word of explanation. Of all mine-records, survey notes are perhaps the most important. The maps made from them serve as a working-guide, and as framework for other data ; and when, from any cause, access to underground workings is shut off, the surveyor's record often becomes invaluable. So seldom does a surveyor have a chance to check underground surveys by making a closure, that he is compelled to rely on the precision of each step of his work for the accuracy of the final result. When data are fully recorded on the spot, the notes, even in the hands of second parties, become evidence of the care and precision with which the surveying was done. It is worth a great deal to be able to pick up the work of a former surveyor where it was left o$; and to be able to carry it forward without retracing from the beginning. The purpose of this paper is to describe the survey-note system of a mine now under my direction, in which underground surveys had to be relied upon entirely for the proper division of rich ore-bodies between neighbors, thereby placing a premium on accurate surveying and permanent records. In survey-work, it soon turns out that paper is the least item of expense, and that little is gained by trying to economize note-book space. For many purposes it is best to record notes on cards or loose-leaves, which may be left in the office at the end of the day's work, and need not be carried into the mine again, there to become smeared with grime and grease. With the loose-leaf or card system, all notes relating to the same local-

Apr 1, 1911

By N. LILIENBERGS

DURING the past few years, the requirements for steel have been raised so high that soundness is more important than ever before. The old practice was to mike steel ingots of sufficiently large sections to permit a considerable reduction of area in rolling and hammering to a given size, relying on the fact that by such rolling and hammering all cavities will be squeezed together and practically eliminated. The finished sizes, if found by inspection of the surface to be faultless, were therefore pronounced to be sound. But when such steel is ?worked up,? the manufacturer is surprised and disappointed to find that it splits, or that streaks and seams make the product unmarketable. Large sections, such as rails, beams or heavy forgings, may, within certain limits, be sufficiently strong, even if the sides of the cavities are only squeezed, and not welded together. But it is well known that, in the interior of heavy articles, under certain conditions, forging may develop small streaks into large cavities. Small sections, steel for ordnance and tubes, and numberless articles in the tool-trade, always show up the defects. It may be doubted whether cavities in steel ingots can ever be completely welded. The old theory, is, that the silver-clear blow-holes, without the blue oxide, can be welded by sufficient working. They are, however, not empty, but are filled with carbonic oxide. It is admitted that the "blue" cavities, resulting from air mechanically drawn down into the mold during the casting, can never be welded, because the oxide does not melt, and there would be no escape for it if it did. The only way in which steel can be made satisfactory for the above-named particular purposes is by having it ?dead molten." But then the trouble of piping is encountered. As is well known, a pipe is the result of the contraction of

May 1, 1906

By Ralph Arnold

WITHIN the past three weeks the price of crude oil in the Mid-Continent field has been cut 50 .per cent. Similar action has been taken, or probably, shortly will be taken, in most of the other fields of this country. This cut is very drastic. Is it justified? Some of the causes advanced for the cut are: that it is in line with the industrial downward readjustment now taking place throughout the country, and that there is an over-production of oil, which can best be slowed down by lowering the price of crude. In part, these two reasons are logically advanced, but such underlying causes as the great production- in Mexico have not been prominently brought forward nor the fact that it would be advantageous at this time to fill up the empty storage of many of the consuming companies at a low 'price. In order to properly comprehend the situation let us compare for a moment the production- of oil in the United' States and that in Mexico. Oil in the United States occurs in numerous often widely separated pools, varying in individual area, but each usually relatively extensive, compared to the area or gathering ground from which it is ultimately derived: It occurs in mod-erately porous reservoir rocks under such conditions of pressure, mobility and availability as to preclude its withdrawal except over a period of years-varying from 1 to at least 40 (average, say 15 years, depending on-the pool). One well will usually drain a limited area-2 to 10 acres-so that rate of withdrawal of oil under each owner's property is determined by the owner. - The important point to remember is that no matter how intensive the development, the oil reserves of -the United States cannot be materially exhausted' for at least 20 years, and the total available supply, not including shale oil, will probably require 50 to 75 years, or longer, for its withdrawal, the yearly rate of production decreasing slowly from this time on.

Jan 1, 1921

By Beall, John V.

THIS is not simply the story of how a water filled shaft was developed into a million-ton- a-year producing mine in the space of four critical years, although it is reason enough for telling it, but it is also the saga of an engineering achievement in which knowledge nurtured by years of experience in coal and ore mines was blended together and the best from each type of mining selected. The entire system of mining was detailed on maps by the mining engineering department before the shaft was unwatered, and subsequent development followed these plans nearly to perfection. The selection of machinery was particularly critical as it was necessary to push production from only a few headings in the early stages of development and metal mine machinery was being used in a coal panel-system of mining. At the start of World War I1 the demand for iron ore to supply Woodward blast furnaces, and rapid exhaustion of the main source of Wood- ward ore, No. 3 Red Ore mine, necessitated speedy opening of the Pyne mine. The mine is three miles southwest of Bessemer and is responsible for 80 pct of Woodward ore, the rest coming from the Songo mine. The Woodward Iron Co. is one of the old producers of the Birmingham district. S. H. Woodward, an iron-master of Wheeling, overheard two Union soldiers conversing about ore and coal lands in Alabama, which lead to the acquisition of the first ore lands of the Woodward Co. in 1869. Development was not begun until after the death of S. H. Woodward; his two sons, W. H. Woodward and J. H. Woodward, formed the Woodward Iron Co. in 1881 and purchased a tract of land midway between the ore vein on the southeast and the coal field on the northeast about 12 miles southeast of Birmingham for the

Jan 1, 1950

By Robert H. Richards

Tuns truly remarkable machine was built on a preliminary scale in May, 1895. The first full-sized table was built by Mr. A. R. Wilfley, and was used in his own mill in Kokomo in May, 1896. The first table sold for installation was placed' in the Puzzle mill, Breckinridge county, in August, 1896. The mill enthusiasts at first hailed it as the cure for all the ills that flesh is heir to in the milling line. A little later it was found to make losses which were serious, and on this account the table succeeded only to a limited extent in displacing the vanners of the gold-mills. Still later, mill-men in a number of districts throughout the country made special studies of the faults of the machine, and devised a number of ways of grouping supplementary machines to overcome as far as possible the losses, and at the same time retain the benefit of the extraordinarily large capacity accompanied by the production of clean concentrates for which the machine has become so justly famous. I hope to make an exhibit of some of these methods in an appendix to my book on ore-dressing which is now in preparation. These experimenters have not written up the subject, and if they possess all the facts they have not given them out for the benefit of the mining profession at large. The object of this paper is to obtain the facts and to pre¬sent them so clearly that their bearing can be seen by all. To this end two complete series-'of tests have been planned. One (the present paper), to study concentration of galena in presence of quartz; the other (to follow shortly), to study concentration of chalcopyrite in presence of quartz. Some authorities claim that the table does its best work when treating natural products; by this phrase I mean products which have been crushed to pass through a limiting

Jul 1, 1907