Search Documents

By J. Walter Scott

IT is usual practice in the copper industry to use open horizontal molds for casting tough-pitch copper wire bars.1 A wire bar cast in this manner is partly characterized, by heavy wrinkles and a comparatively deep skin of oxide on the top of the bar, corresponding to the open side of the mold. On the theory that the rough, high-oxide surface might have an adverse effect on the rolling and drawing properties of a wire bar and might account for some of the irregularities of mill behavior, several bars which had been planed to remove the wrinkled surface were processed into wire. These bars responded to mill treatment more satisfactorily than did the regular wire bars. Realizing that machining the surface of one face of each bar would not be commercially feasible, it was decided that casting the metal into a vertical mold and cropping off the pouring end would accomplish. approximately the same result. Several wire bars of commercial size (250 lb.) were so cast and processed into wire for comparative test with bars cast in the usual horizontal molds. It is the purpose of this paper to present the results obtained from this investigation, in which commercial bar sizes and processing technique were used throughout. The results show that in general copper wire bars cast vertically are superior to those cast horizontally.

Jan 1, 1930

By S. Y. Han

INTRODUCTION More than 97% of the total uranium production of the United States comes from sedimentary deposits (1). These sandstone deposits were formed by reduction of migrating uranium-bearing solutions from volcanic silicate rock sources. Such deposits occur in two major forms, either as relatively flat, lens-like deposits or as crescent- shaped roll front deposits. The lens-like deposits are found as discrete masses enclosed in reduced sandstone which is generally surrounded by oxidized sandstone. The roll front deposits are found along crescent-shaped interfaces between reduced and oxidized sands tone (2). In-situ mining of selected sedimentary deposits has proven to be a viable method of extraction and competitive with conventional mining for relatively deep low-grade ores (2). In in-situ leaching, uranium is recovered by drilling injection and collection wells in the ore body, pumping a suitable lixiviant to dissolve the mineral, extracting uranium from the pregnant solution by ion exchange, and finally regenerating and recycling the lixiviant. Even though there is increasing interest and practice in developing the in-situ technique for obtaining uranium values from deeper, lower-grade reserves, there is a lack of knowledge of the basic leaching kinetics and combined transport processes. In-situ leaching operations, in general, appear attractive for the following three general types of deposits (2): (1) low-grade surface dumps or deposits which lie above the natural water table,

Jan 1, 1983

By E. P. Bucklen

Simulation is a tool useful in the evaluation of the probable effect which various changes may have on the performance of time-dependent systems. This is especially true as far as rail transportation in mining is concerned. The VPI-OCR RAILSIM program is a computer program designed specifically for solving a broad range of problems encountered in the design of haulage systems of new mines as well as in the operation of haulage systems in existing mines. This program is one of several computer applications for evaluating mining systems developed at the Virginia Polytechnic Institute and State University under contract with the Office o f Coal Research of the U.S. Dept. of the Interior. The RAILSIM program uses Monte Carlo techniques to introduce variability in the occurrence of events such as would be observed in real systems. Data are required to describe the haulage network, locomotives, stationary facilities, and other miscellaneous parameters. Output from the program lists measures of performance that are useful in assessing the capabilities and limitations of given system configurations. The output information may cover many shifts of operation to indicate the broad range of variation and interaction which can occur as the system responds to varying levels of demand for service. The RAILSIM program was tested extensively in mining operations. The results of some of these tests are used to illustrate the usefulness of this program.

Jan 1, 1972

By John E. Dowis

Ore distribution being what it is, many of today's mining companies are forced to develop foreign reserves to satisfy the demands of their customers. This necessity complicates the economic picture for a company, because management must look well be- yond grade and tonnage to determine the feasibility of developing a foreign orebody. Above all, the taxes on such a development must be assessed. The difference that taxes can make in mining profits will be illustrated here for three countries-Canada, Mexico and the United States. For purposes of comparison, identical orebodies will be assumed to occur in all three countries. Only the taxes on these properties will vary. Grade, tonnage, gross income, production costs and production rates will all be the same. The discussion will be limited to federal taxes, because state and provincial taxes are usually negligible by comparison. Assumptions relative to the orebody and the nature of the company undertaking the operation are as follows: (1) Copper is the only value to be recovered. (2) Sixty million tons of ore have been delineated. (3) Underground mining is required, and the production rate will be 3 million tpy. (4) The life of the property is 20 yr. (5) Operations in Mexico or Canada will be handled by a subsidiary of a U.S. parent company. (6) The subsidiary will offer stock.

Jan 1, 1970

By S. R. B. Cooke, R. O. Huch, C. S. Chang

IN the flotation of iron ores laurylamine derivatives have been used for considerable time.1, 2' To effect satisfactory separation of the gangue, pre-dominantly silica, from the iron oxide minerals, the addition of specific depressants for the iron oxides has been found necessary. Starches and starch products have been used for this purpose.V here is, however, very little published information on the effects of these materials and other variables on this process. In some cases it has been found that prior acid scrubbing and desliming are essential," and depending upon the efficiency of the subsequent washing step, there will be accompanying changes in pH. It was the object of this investigation to test and observe the effects of the above factor as well as to examine and compare the action of various starches and starch products. Ore Preparation The ore used in this experiment was a wash-ore tailing obtained from the western Mesabi range. Microscopic examination and x-ray analysis of the ore showed it to consist of hematite, goethite, and quartz. Physical properties of the iron minerals ranged from hard and crystalline to earthy and ocherous. The quartz grains were discolored either because of iron-oxide inclusions or because of a sur-face coating of iron oxide. The ore assayed 27.52

Jan 1, 1954

By C. K. Leith, W. J. Mead

One of the most significant developments in the iron industry in recent years has been the discovery and opening of enormous reserves of low-grade ore in eastern and northeastern Cuba. The two principal fields are the Mayari and the Moa, situated on Nipe bag, in the Province of Oriente. A less well-known district of the same type is that of Baracoa, at the east of the island, and another is in Csmaguey Province in central Cuba. In the comprehensive estimates of the iron-ore reserves of the world, published during the summer of 1910 by the International Geological Congress in Sweden,' these Cuban deposits are estimated at about 2,000,000,000 tons. Certain it is that the reserve is a large one. The Spanish-American Iron Co., the Juragua Iron Co. (Bethlehem Steel Co.), the U. S. Steel Corporation, and others have been active in this exploration. The Spanish-American Iron Co. has established a port for the handling of these ores at Felton, has built a railway 16 miles to the ore-fields, and has operied up deposits for steam-shovel mining. Its expenditures have reached an aggregate of about $6,000,000 in preparation for the handling of these ores. Shipment of the ore to Sparrow's Point, Md., has begun and may be expected to rise to a considerable amount in the near future.

Jan 1, 1912

By Raja P. Upadhyay

An evaluation of the economics of mining the deep, thick oil shale deposits of the central portion of the Piceance Creek basin, Colorado, U.S.A. is presented in this paper. For the analysis, a modified large scale underground mining system developed by Cameron Engineers, Inc. and the Gas Combustion retorting process developed by the U.S. Bureau of Mines were used to determine capital investment and annual operating costs. A modified risk analysis computer program was then used to calculate DCFROI’s for various grades of oil shale and selling prices of partially refined shale oil. Sensitivity analyses were performed to quantify the affect of bonus bid payments, operating costs, capital investment, and all costs on DCFROI. In addition, a probabilistic evaluation was made to determine the risk involved in obtaining desired rates of return. Results of the economic evaluation indicate that for current selling prices of crude oil a high risk is involved in obtaining a DCFROI of 15%, unless only higher grades of oil shale are mined. However, mining only the higher grade oil shales, 125 l/mt (30 gpt) and above, would effectively reduce the potentially mineable resources by 90%. Risk can also be reduced through higher selling prices of shale oil. Sensitivity analyses indicate that the capital investment has a three times greater effect on required selling price than total operating costs.

Jan 1, 1977

By D. W. Gillmore, C. C. Wright

DEWATERING is a major problem in the preparation and utilization of fine-sized coals now being recovered in increasing amounts from colliery effluents, refuse banks, and silt ponds. Of the various methods which have been proposed for dewatering fine coal, gravity drainage is probably the oldest and most widely used, and yet little information on this subject has been published. Consequently a laboratory investigation of gravity drainage phenomena was undertaken not only to provide basic data for predicting the drainage behavior of fine coals in cars, bunkers, basins, and silos, but also to obtain some understanding of the moisture retention properties of fine coal. Because of practical interest in the problem, a reproducible laboratory technique, which simulated plant conditions as closely as possible, was developed for the evaluation of drainage variables. The apparatus selected consisted of vertically-mounted lucite columns, nominally 4 to 8 ft in length and 2, 3 or 6 in. in diam; the bottom of the column was provided with a rubber stopper through which was inserted a ½ -in. diam drainage tube; a wad of glass wool was placed on the upper part of this outlet tube to retain the coal and a plug was temporarily located at the lower end to prevent drainage during charging of the column, see Fig. 1. The most satisfactory testing procedure is as follows: 1-The fine coal, which has been thoroughly

Jan 1, 1952

By Everett Parker

THIS paper describes the methods used to determine the rates of payment for contract work and the plan of contract supervision in the Elm Orlu mine. A discussion of the theory of wages and the eternal question-what is a just wage-are beyond the scope of this article. In the fall of 1920 the Elm Orlu was the largest mine in Butte using the day's pay system of payment for stoping operations. High labor and supply costs and a falling market for the product of the mine made economic mining difficult. The mining method had been changed from the square set stoping to timbered rilling to eliminate most of the shoveling. There was no opportunity to reduce the cost of supplies other than more rigid economy in their use. It was recognized, however, that the labor efficiency was low and that the reduction in costs depended on increasing the output per man. While in general, the low man efficiency was a resultant of the high wages paid and the shortage of men during the war and subsequent period of inflation, it was felt that the contract and bonus system used in the other mines was the main factor in that the most capable and energetic men had been attracted to those mines where more than average skill and dili-gence were recognized by more than average pay.

Jan 1, 1927

By K. Matsuda, H. Tanaka, M. Mamiya, H. Majima

Copper cementation was studied from both thermodynamic and kinetic aspects. The temperature effect of copper cementation, which has been recognized as an anomalous result, and the rate enhancement phenomenon observed after the initial linear step are, in particular, focused in this work. The main results obtained are as follows; 1) Free energy changes of copper cementation reactions, calculated by the use of the "Correspondence Principle" of Criss and Cobble are rather insensitive to temperature. 2) A Flow-cell assembly consisting of a special cupric ion electrode, a calomel electrode and a potentiometer is particularly useful for the continuous measurements of copper cementation rate. 3) Two first-order reaction rate constants for the CU2+- Fe system were successfully determined by the use of the flow-cell assembly. 4) Activation energies determined for the initial rate and the 9 maximum rate of CU2+ - Fe system are both 4.6 kcal/mole. This fact suggests that the mechanisms of the initial reaction and the final reaction are essentially the same and both reactions are rate controlled by the diffusion in a boundary layer. The difference in the rate constants of them may fie explained by the effect of the nature of surface deposits. 5) Qualitative explanation of the rate enhancement phenomenon from the initial rate was successfully made by applying Bockris "Penetration Model."

Jan 1, 1976

Hunkered up against the spine of the Andes in a tight valley where natural refuge from avalanche hardly exists is the daring Rio Blanco project of Cerro Corp. The deposit here was found in 1904, but nature has foiled all previous attempts to open it. To an experienced mountaineer or a highway engineer with mountain experience, the avalanche hazard in the valley of the Blanco river would be immediately apparent. The collar shaft is at the head of the valley at an elevation of 3600 m and for 12 km down the valley there is no space on the floor for building very much; the dissected rock walls are roadways for avalanches and even a highway could not be maintained sufficiently passable. This is the proposition taken on by the Cerro Corp. Chilean National Decree #1699, passed on December 9, 1966, signified "Go" to the Compania Minera Andina, a company whose shares are held 70% by the Cerro Corp. and 30% by the government of Chile. The orebody, although only partially delineated, contains proven reserves of 120 million tons of ore averaging 1.58% Cu. When the operation comes on stream in the last quarter of 1970, it will be at the rate of 11,000 tpd. Annual production will be 65,000 tpy of recoverable copper in concentrates.

Jan 11, 1969

By W. C. Schroeder

PRACTICAL experience has shown that at elevated temperatures solu-tions containing sodium hydroxide may attack stressed steel in a manner that cannot be explained in terms of ordinary corrosion. Because the ductility of the metal has been greatly reduced during the reaction, the entire phenomenon is usually called "embrittlement." Thus, after several years of operation caustic evaporators have been so badly embrittled that rivets could be cracked off with the blow of a hammer. Since fine intergranular cracks are almost always present in the zone of fracture, it has often been assumed that a process of selective corrosion in grain boundaries was responsible for the failure, although this has not been clearly proved experimentally. Concentrations of sodium hydroxide below those necessary for the uniform, rapid attack of the steel surface are reported to be most effective in producing embrittlement2,3. In the operation of steam boilers a similar type of failure has been found, mainly in riveted seams or other capillary spaces where the solu-tion may concentrate and where high stresses may also exist. It is believed that in such localized areas the dissolved solids may reach a value many times the few hundred parts per million prevalent in the body of the boiler. While this type of boiler failure has been the subject of investigation for a period of 20 years', an understanding of its mecha-

Jan 1, 1936

By Donald E. Crowell

In the fall of 1969, ASARCO and Newmont Mining Co. began the design of the 700tpd concentrator at their Black Cloud shaft located near Leadville, Colo. The concentractor would treat by flotation a Pb-Zn-Ag ore containing minor gold values. Flowsheet design was based on laboratory test work performed at the Minerals Research Testing Laboratory of ASARCO. Since the concentrator is located at an elevation of 11,000 ft, cold weather was a major factor in design considerations. The original capacity was designed as 700 tpd but for various reasons an ultimate capacity of 1,000 tpd was desired. This necessitated special consideration in the design of several areas, particularly the grinding circuit. The grinding circuit chosen was a single 9 X 12 ball mill operating in closed circuit with one 20-in. cyclone. The ball mill will operate at low speed and as an overflow type originally. The mill can be speeded up and converted to grate type for handling the larger tonnage when required. Thickeners and filters were oversized and space was left for additional flotation cells in order to handle the increased tonnage in these areas. Pumps were sized so that they could handle the increased tonnage by increasing their speed. Construction began in May 1970; the Black Cloud concentrator went on-stream in April 1791.

Jan 1, 1974

By John A. Emery, Frank G. Snyder

Mining geology has a threefold objective: to guide prospecting for new ore, to evaluate known orebodies as development risks, and to supply the detailed knowledge of ore structures necessary for more economical extraction. The role of geology in exploration is well established. This article will deal solely with orebody evaluation and the application of geology to development and mining problems as practiced by St. Joseph Lead Co. in the southeast Missouri district, which for many years has supplied approximately 30 pct of U. S. lead production. The primary concern of the present discussion is geology in the district, not geology of the district. The southeast Missouri district, locally called the Lead Belt, includes parts of St. Francois, Madison, and Washington counties. The first recorded mining was about 1720 at Mine La Motte in Madison County on surface showings of lead ore. Later discoveries near Bonne Terre, twenty-five miles to the north, led to extensive prospecting and underground mining. To date the district has yielded well over 8 million tons of pig lead, valued at more than $1 billion. By far the greater part of the lead production has come from an area of 50 sq miles, centering Fig. 1-Central portion of southeast Missouri on the city of Flat River, as shown in Fig. 1.

Dec 1, 1956

In the late 19th century Fremont Pass was only a gateway to Leadville, Colo., 12 miles to the north. Some of the silver, lead, and zinc won from this famous camp crossed the Continental Divide at Climax, passing by the huge outcrop of molybdenum on Bartlett Mountain. This element, relatively un- known in the world of commerce, was then nothing more than a joke to play on greenhorn prospectors. Even 30 or 40 years later, after the demand for metals created by World War I had forced temporary use of molybdenum as an alternate for tungsten in tool steels, the Bartlett Mountain outcrop once again became merely a curiosity. With the persistent efforts of Brainerd Phillipson, for years the president of Climax and almost the only employe, use of molybdenum gradually began to grow, first in tool steel and later in the alloy steels required by the growing automotive industry. Mr. Phillipson was first an engineer and second a salesman. The combination of these two qualities is the key to the story, not only of Climax sales but also of the growth of molybdenum from an object of idle curiosity to the point where it is today, along with chromium and nickel, one of the most versatile alloying elements in the iron and steel industries and increasingly important in chemistry.

Aug 1, 1955

By L. O. Bond, R. P. Alger, A. W. Schmidt

Well logging provides valuable information for planning coal mining operations. In addition to locating, defining, and evaluating coal beds, electrical logs indicate the relative competence of roof and floor formations. Electrical well logging is the .recording of various physical, chemical, or physicochemical properties of the strata penetrated by a drill hole. To perform logging operations, borehole measuring probes, or sondes, are lowered on a cable into the drill hole. Insulated conductors in the cable pass power to the sonde and transmit signals to the surface. As the sonde is pulled up the hole, the measurements are recorded as a well log. These measurements serve to define the formation lithology. Common rock minerals exhibit characteristic log values such that computer analysis of the log data defines the mineral content of the formations. Shales, carbonates and sandstones, and coal beds are readily distinguished. Furthermore, preliminary results in coal studies indicate the log data delineates variations in ash and moisture contents. Of major concern in planning mining operations is knowledge of roof and floor competence. Here again the logs provide valuable information. Measurements of formation density and acoustic wave velocity provide data for computation of a compressional modulus. This compressional modulus is an effective index of formation competence. Electrical logging thus efficiently provides information for economic planning of mining operations.

Jan 1, 1972

By Yap Chu-Phay

IN the previous paper, the writer showed how, on the basis of thermodynamic reasoning, it seems probable that when true equilibrium conditions obtain, carbon exists as Fe3C in the liquid state and as elementary carbon in the solid state (7 Fe), in which case the solidus would be a straight line from 0.18 to 1.70 per cent. carbon (Fig. 1). In the same paper he concluded that the solidus obtained by Honda 'and his co-workers1 probably does not represent the same conditions, insuring a complete equilibrium. Except for a downward temperature displacement, the solidus obtained by Gutowsky,2 using the Heycock and Neville method, practically coincides with Honda's solidus as shown in Fig. 1. The writer at first thought that perhaps in some way Gutowsky's thermocouple was improperly calibrated for high-temperature measurements, as his liquidus was also much lower than those obtained by Carpenter and Keeling3 and by Ruer and Goerens.4 However, the eutectic temperature obtained by Gutowsky agrees with the generally accepted value of 1130° C., so that the validity of the inference regarding improper temperature calibrations is to be strongly doubted. In Fig. 1, Gutowsky's solidus is shown both in the original and in the corrected form. In the latter, a correction of 29.2° C. is made for all temperatures above 1416° C. in accordance with-

Jan 1, 1931

By H. B. Treweek, V. R. Degner

Current mineral industry trends toward handling the high tonnages of lower grade ore and tailings retreat lead to a continuing need for large volume flotation cells. The benefits which accompany the larger cell flotation circuit include reduced capital cost, less mill floor space, reduced operational complexity, and less maintenance, provided the metallurgical performance and solids suspension capability of the cell are not compromised. This study reviews development considerations pertinent to large mechanical air induction type flotation cells from the standpoint of cell internal hydrodynamic characteristics and metallurgical performance. While the importance of process related factors such as chemical usage, pH control, solids size and loading, and circuit arrangement cannot be denied, this study will emphasize the relationship of cell size (volume), mechanism geometry (impeller diameter), and mechanism operating conditions (rotor speed and submergence), to air transfer, liquid circulation, liquid "rise velocity" and mechanism power draw. Specific hydraulic performance maps for large capacity 300 and 500 cu ft flotation cells will be reviewed in terms of the relationship between the operational variables and the air and liquid flow conditions within the cell. Metallurgical results, obtained under plant operating conditions for 300 and 500 cu ft cells, are included to illustrate the metallurgical performance similarity of flotation cells which follow hydrodynamic scale-up criteria set forth in this investigation.

Jan 1, 1976

By F. L. Holderreed

A choosy in what they would smelt. The furnace charge had to be coarse, and it had to be rich. They discarded fines in excess of about 1/10 the total weight. They wanted 10% copper content and fussed about anything with as low as 5%. They concentrated the copper content of the charge as much as they could by prior selection. They roasted off enough sulfur to further enrich the copper content of the succeeding fall of matte (a melt of cuprous and ferrous sulfides or Cu2S.FeS). Then they desulfurized the iron and fluxed it by carefully adding silica (quartz, not silicates) for a slag of lower density than the cuprous sulfide (Cu2S or white metal). After skimming off the slag, they further desulfurized the white metal by blowing the molten bath with compressed air. The result was blister copper. Yesterday Their techniques and furnaces? Some experimented with mechanically rabbled roasters, but their standard roasting practice was burning coarse sulfide ore in 250-ton heaps. These heaps, approximately 24 x 24 x 6 ft, were burned for about 75 days down to 6-10% sulfur. The turnaround time for a given roasting position was 100 days. Assuming the base was a hearth, the calculated rate of treatment was on the order of 0.004 tpd per sq ft.

Jan 1, 1971

By R. C. Davis, R. F. Berry, G. W. White, B. T. O’Connell, L. A. Stacha

P,, and v, may now be solved for by trial and error between Eqs. 2 and 3, by assuming time approaching zero and equating PI, to P12. Observe that the pressure under the slug, P12 of Eq. 3, does not remain equal to the P1, at the valve in Eq. 2 as the slug proceeds up the hole. To plot the profile of pressure vs depth, it is necessary to express P12 in terms of P11. To do so, the extent to which the original submergence length S changes with respect to time must be analyzed. At the end of time t after injection, the actual value of L in Fig. 3 is The fall-back v,(t) is now distributed in the gas and exerts pressure on the bottom. This, in addition to the weight of the gas, amounts to the difference in pressures from point to point. With the average pressure profile calculable, a true numerical value for the average pressure in the tubing may be obtained. The value of v, must be obtained experimentally, and since v,, S and D are known, the basic Eq. 1 may be solved for the amount produced. Knowing P, and the actual volume of tubing occupied by gas (vat), it is possible to calculate the volume of gas at standard conditions which is present in the