Search Documents

By William B. Phillips

The possible sources of potash salts in the United States have been considered from many points of view during the last several years, but it is only within the last two or three months that the situation has become acute. We import from Germany, the only sourcc of large supply, more than $10,000,000 worth of potash salts annually, and this business has been badly crippled by the European war. If there was ever a time in our industrial existence when the necessity of providing for our own needs was more acute than it is now, we are not aware of it. One has only to study the price lists of chemicals sent out by the large supply houses to see the change wrought within a very short time. Whether or not these prices are to maintain for a considerable time, no one can say; but it appears to be probable that we shall not see prices materially lower for a period of uncomfortable length, to say the least. It is not my purpose at this time to discuss the various sources of supply of potash salts that have been suggested or recommended. Some of them might afford a pleasing relief but all of them combined would not affect the situation seriously. If we are to have our own sources of potash salts, they will have to compare, in some efficient manner, with the sources upon which we have drawn during the last 20 or 30 years; i.e., they must exist in minable quantities. It seems to me to be quite idle to speculate upon our domestic sources of potash if those sources are not of a character similar to those upon which we have so long depended. A few thousand or, perhaps, a few hundred thousand dollars' worth of chemically derived potash may be produced under the stress of present conditions, but when we consider that each year demands more than $10,000,000 worth, we must look to underground sources; we must look to mines similar to the famous Stassfurt and Halle deposits. If we cannot mine potash salts, we shall have to do without them for a while.

Jan 1, 1915

By Thomas L. Garwood, F. C. Menk

IT is generally, accepted that no method of coal cleaning except froth flotation is effective in cleaning dust. In the majority of coals mined in the United States the dust sizes contain a high percentage of impurities, hence the removal of the dust from the coarse sizes lowers the impurity content of these sizes. Dedusted coal is desired as a means of providing a better feed to cleaning plants because of increased efficiency in both dry and wet plants. In dry-cleaning plants, a dedusted feed makes for a pervious and uniform bed. With a dusty feed the fines tend to segr6gate in the feed stream and pass en masse over the air separators, causing a lack of uniform aeration and fluidity of the bed necessary to efficient cleaning. In wet-cleaning plants dedusting of the feed often decreases the sludge problem to the point of eliminating the necessity of wasting wash water. It may be advantageous to eliminate sludge-settling equipment in favor of dedusting equipment, to provide the advantages of a dedusted feed to the wet-washing process. Dedusting advantages may include: (1) the removal of fusain, especially advantageous in plants washing coal intended for metallurgical coke; (2) prevention of the gradual build-up of solids in the wash water, with a consequent variation in the washing ability of the system; (3) prevention of the loss of dust to the sludge ponds, providing instead a fuel for local consumption or special markets. DEDUSTING The practice of dedusting, sometimes called aspirating, has presented a problem in disposing of the dust and intermediate small sizes recovered in the process. It has been found that no difficulty is experienced in disposing of the intermediate sizes, since they are free of fine dust and burn freely on grates built for small coal. They handle well, flowing freely from bins and hoppers and into conveyors, and pulverize easily. They have a low angle of repose. In tests made on this size as a feed to coke ovens, the results have been excellent, in that the natural breakdown of .coal in handling and shooting in the mine gives this small-size coal good

Jan 1, 1943

By Henry D. Hibbard

At the beginning of a Henry M. Howe lecture it seems fitting to refer to Howe's great contributions to steel metallurgy, and particularly to the literature thereof. Most of my predecessors in this role have been able, from their association with him, to give direct testimony as to his great services; but although connected with him for years in a business way, I am less familiar with what might be called his academic side, except as it is embodied in his utterances, written and oral. Howe was adept in his genial way in extracting information in any line which, at the time, was of interest to him. In a technical lecture one expects as a rule new knowledge—something about recent advances relating to the subject. On this occasion, however, I will ask you to go back with me to the primary department of steel lore, as the title of my lecture shows, to review the more fundamental features in that field for the purpose of seeking some gaps which we can fill and so give the subject renewed interest. In thus going back one must inevitably repeat many familiar facts, but that seems to be necessary in order to reach a clear understanding of the unrecorded matters. The full interpretation of a steel analysis is at present unattainable, though much progress toward that end has been made. The ultimate analysis, giving the percentages of the five commonly determined elements, does indeed usually give a fair idea of what the steel is, and is ordinarily enough, with knowledge of its history and physical condition, to enable it to be assigned to some purpose or use for which it is reasonably suitable. But discrepancies arise. Every maker and every user of steel knows, from at least occasional examples in his own experience, that the ultimate analysis is insufficient by itself to enable one to tell positively, from its interpretation, either the mechanical properties of the steel or its adaptability to the purpose for which it was made. Further, if, while having the specified composition, it is abnormal or unsatisfactory, why it is so. Good, bad and indifferent steels may have substantially the same ultimate analysis.

By P. W. Bridgman

IT is characteristic of most scientific investigators that they are not satisfied with the discovery of new facts, no matter how curious or unex-pected, but that along with the factual discovery there is a constant effort to understand. It appears that one's interest in, and satisfaction with, the discovery of an array of new experimental facts is enormously increased if one has at the same time a theory or hypothesis guiding one's expectation of what sort of new experimental discovery may lie around the corner. Conversely, as a theoretical physicist one's satisfaction with his theory is greatly enhanced if along with the development of the theory can go the discovery of new experimental facts, confirming or perhaps modifying the theory as it grows. Of course, there have been long arid stretches in the history of physics in which new data of unquestioned ultimate importance have piled up, without much inspiration or illumina-tion in the way of understanding. For 50 years spectroscopy had such an arid history, but how irksome this was felt to be is plainly shown by the almost audible relief that greeted the first success by Bohr in injecting understanding into the situation, and by the fresh rush of experimenters into this field when the prospect of understanding had once been offered. The investigations in the field of high pressure, which have occupied me for a long time,1 until the last few years have been in very much the same sort of situation as spectroscopy before the advent of Bohr. A great many kinds of data were collected for a great many solid and liquid sub-stances, and there could be no question of the importance of these data, because the uniform change of dimensions produced by hydrostatic pressure is perhaps the simplest conceivable type of alteration to which a body can be subjected. But except for a few isolated flashes, there was no theoretical illumination, so that it had to be to a large extent the enthu-siasm of the collector that kept me going. However, within the last few years the wave-mechanics theory of solids has progressed so rapidly that

Jan 1, 1938

By Thomas Darlington

The obligation of an employer to the State requires certain things of him as matters of good citizenship: for instance, that his workmen shall have a living wage, that child labor shall not be employed, that injuries from accidents shall not make workmen a charge upon the State, and that the laborer's children shall have opportunity for education and to become good and useful citizens. Affairs of this kind are not taken up as philanthropy, for the officials of a corporation or a large manufacturing concern may not feel at liberty to spend the funds of their company as prompted simply by motives of kindliness; but they may spend company money on such matters because it is good business. For years, the poisonous effects of lead, phosphorus, and dust have been emphasized in books on industrial hygiene and their elimination has been urged; but the more important and everyday physiology of the workman himself has been neglected. Part of my object in writing this paper is to show how our knowledge of physiology may be applied to working conditions in everyday life. In the interest of industrial laborers, accident compensation laws have been enacted in 33 States. This has been carried forward rapidly, because it has been shown that it pays both employer and employee. A further step is the recognition of sickness and disablement independent of accidents, not only because of their immediate cost to the worker and to the employer, but because continued efficiency in work and business depends largely upon health. Some measure of the importance of health in industry can be gained by the knowledge that records kept by some companies which now make this the subject of careful inquiry show that the time lost by employees, through illness, is several times as much as that lost as the result of industrial accidents. It is true that accidents frequently result in permanent disability or death, but it is equally true that illness is also a cause of permanent disablement or death. Thus the chief difference is that the loss to the employee through accidents occurring in the course of his employment is now generally recognized as a cost

Jan 1, 1918

By N. A. Rose, E. L. Spain

THIS study was undertaken primarily to determine the reasons for certain variations in the soundness of gravel aggregate taken from a number of widely separated points on the Tennessee River. Under laboratory tests, concrete made with these various aggregates in some cases exhibited marked differences in specific gravity crushing strength and durability. Gravel was studied in detail from Chattanooga to the mouth of the river and to a lesser extent from Chattanooga to Knoxville. The causes of variation were determined, and variational curves were constructed, which accurately predict the composition of aggregate at any point on the river and therefore its relative suitability for use in concrete. The aggregate at any point is suited for making sound concrete; the variance of suitability is due to varying percentages of sandstone and weathered material, which are less sound than other constituents. INTRODUCTION When it is stated that the aggregate from one point is inferior to that from another, it must not be construed to mean that the gravel is unfit for use. The classification upon which such aggregate ratings are based is largely arbitrary, thus inferiority or superiority is merely relative. Samples of gravel were selected from stockpiles at the dams of the Tennessee Valley Authority under construction, from the stockpiles of private companies along the river, and from samples taken by the gravel- exploration barge of the T. V. A. One hundred or more gravels of each size studied were selected at random by taking small handfulls while walking around the piles. These were separated according to the different mineral or rock constituents present, and the percentage of each constituent was obtained by counting. At least three such samples were taken from each size, and all checked with one another within a few per cent. The results were then averaged. In order to check on the accuracy of such sampling, a whole sample was taken from one point after the gravel was thoroughly mixed. The two methods gave approximately identical results. SOURCES AND TYPES OF MATERIALS The sources of gravel found in the Tennessee River are numerous and varied. The river itself traverses several geologic provinces, each

Jan 1, 1937

By C. E. Abbott

The Birmingham district, Alabama, is distinctive in the proximity to one another of its deposits of iron ore, coal and flux. These three basic requisites for the making of iron and steel are found within a radius of 10 miles. Both dolomite and limestone are produced, the former for blast-furnace flux and the latter for basic open-hearth operations. The Tennessee Coal, Iron and Railroad Co., a subsidiary of the United States Steel Corporation, operates a limestone mine at Muscoda, near Bessemer, 12 miles southwest of Birmingham, served by its own railroad transportation system. The mine has a capacity of 130 tons per hour. Average analyses of a recent month's production arc as follows: Fe²zO³ SiO² Al²O³ CaCO³ MgCO³ Lump, percent............................. 0.51 0.22 98.63 0.14 Crushed and washed, per cent,................ 0.70 0.26 98.36 0.18 Lump stone, 2 1/2 to 755 in., is used in open-hearth operations at Fairfield Steel Works. Fine crushed and washed stone, 1% to 0.063 in., is calcined at the lime-burning plant and used for lime charges at the Ensley open hearths. Geology The district's deposits of hematite ore occur in the Clinton formation, and the limestone beds mined are stratigraphically 330 ft. above the ore beds worked. A cross section on the center line of the mine is shown in Fig. 1. This limestone formation, 130 ft. thick, is in the Warsaw horizon of the Lower Mississippian. It lies above 100 ft. of Fort Payne chert, which is immediately above the Clinton formation, and is composcd of layers of chert and cherty limestone, approximately 50 per cent of the material being pure chert. The chert is extremely hard, and the cost of driving raises through it is very high. Both iron ore and limestone deposits lie on the southwest limb of the Jones Valley anticline, the formations dipping from 15' to 32' to the southeast. The iron-ore seam outcrops along the crest of Red Mountain, a ridge with northeast-southwest trend rising 200 to 300 ft. above Jones and Shades valleys at the

Jan 1, 1938

By A. E. Bellis

There is a wide difference of opinion among rifle experts in the matter of barrel steel, and the relative importance to the life of the barrel of the steel's composition, heat treatment, structure, and physical properties. In order to promote discussion, which it is hoped may' lead to the discovery of the source of some of the traditional beliefs on the subject, the results of some tests are presented here, with data on heat treating, physical tests, and erosion. The detailed metallographic study of this steel is given in another paper.l The conclusions from these tests should be capable of wider application than their direct bearing on the barrel-steel problem. The Government specifications for barrel steel for model 1903 rifle (Springfield) call for carbon 0.50 to 0.60 per cent., manganese 1.00 to 1.29 per cent., silicon under 0.25 per cent., sulfur under 0.06 per cent., phosphorus under 0.08 per cent. The minimum physical requirements are: Tensile strength, 110,000 lb. per sq. in. (7733 kg. per sq. cm.); yield point, 75,000 lb. per sq. in (5472 kg. per sq. cm.); elongation, 20 per cent.; reduction of area, 45 per cent. Material fulfilling these requirements gives practically no failures when proof-fired, with charge of 70,000 lb. per sq. in. pressure, which is 40 per cent. in excess of the service charge. The turning and drilling operations show up any seams or laps such as accidentally occur even in the best heats of open-hearth steel, so that faulty stock is practically all eliminated before proof-firing. These physical requirements are met either by rolling billets at a proper temperature down to the form of tapered barrel blanks or by heat treating bars that have been upset to cnlarge the breech section. The transformation temperature of this steel, on heating, is around 1350" F. (732' C.), varying somewhat with the composition and the rate of heating. The actual treatment of the barrel blanks, as carried out by different manufacturers, gives four kinds of barrels, which will be called A, B, C, and D, for convenience. A barrels result from heat treating upset blanks by quenching at

Jan 1, 1920

By E. L. Spain Jr. N. A. Rose

This study was undertaken primarily to determine the reasons for certain variations in the soundness of gravel aggregate taken from a number of widely separated points on the Tennessee River. Under laboratory tests, concrete made with these various aggregates in some cases exhibited marked differences in specific gravity. crushing strength and durability. Gravel was studied in detail from Chattanooga to the mouth of the river and to a lesser extent from Chattanooga to Knoxville. The causes of variation were determined, and variational curves were constructed, which accurately predict the composition of aggregate at any point on the river and therefore its relative suitability for use in concrete. The aggregate at any point is suited for making sound concrete; the variance of suitability is due to varying percentages of sandstone and weathered material, which are less sound than other constituents. Introduction When it is stated that the aggregate from one point is inferior to that from another, it must not be construed to mean that the gravel is unfit for use. The classification upon which such aggregate ratings are based is largely arbitrary, thus inferiority or superiority is merely relative. Samples of gravel were selected from stockpiles at the dams of the Tennessee Valley Authority under construction, from the stockpiles of private companies along the river, and from samples taken by the gravel-exploration barge of the T. V. A. One hundred or more gravels of each size studied were selected at random by taking small handfuls while walking around the piles. These were separated according to the different mineral or rock constituents present, and the percentage of each constituent was obtained by counting. At least three such samples were taken from each size, and all checked with one another within a few per cent. The results were then averaged. In order to check on the accuracy of such sampling, a whole sample was taken from one point after the gravel was thoroughly mixed. The two methods gave approximately identical results. Sources and Types of Materials The sources of gravel found in the Tennessee River are numerous and varied. The river itself traverses several geologic provinces, each

Jan 1, 1938

By C. H. Mathewson

Discussion of the paper of C. H. MATHEWSON and ARTHUR PHILLIPS, presented at the New York meeting, February, 1916, and printed in Bulletin No. 109, January, 1916, pp. 1 to 50. ZAY JEFFRIES, Cleveland, Ohio (communication to the Secretary*).¬The authors are to be congratulated for this interesting and valuable contribution. The paper as a whole shows very careful experimentation coupled with rare judgment in drawing conclusions. I have been working along similar lines for the last two years with other metals and alloys. In a short conversation with Dr. Mathewson about July 1, 1915, he mentioned the fact that different degrees of cold work greatly affect the temperature of recrystallization on annealing, Later I determined the recrystallization temperatures of iron, mild steel, and copper, with different degrees of cold work and found that the greater the degree of cold work, the lower the temperature of recrystallization on annealing. In the course of these experiments, I conceived practically the same ideas regarding the reasons for recrystallization as those advanced in the article under discussion. After a metal has been reduced by cold work to about one-fourth of its original area, the differences in orientation of different parts of a given grain can be seen plainly at a magnification of about 1,000 diameters. It is interesting to note that in Fig. A, Plate I, the lines of deformation are not parallel. For example,. in the large grain at the lower left corner of the micrograph, if the lines of deformation about 3g in. from the left edge are continued in a straight line, this line will intersect a straight line drawn as a continuation of the lines of deformation on the extreme right of the grain, at an angle of about 20°. Similarly, if the lines of deformation at the extremities of the large grain in the right central portion of the micrograph are extended, the lines intersect at an angle of about 35°. The individual lines of deformation are not straight. In some of these the parts of the broken lines intersect at angles as great as 15°.

Jan 5, 1916

By T. R. Schermerhorn, Samuel L. Hoyt

The hardness of annealed copper has been given in the literature and is easily obtained by any of the standard methods of hardness testing. It is not our intention to correct published values or to add to them, but to describe tests of two bars of annealed electrolytic copper in which the methods of Meyer's analysis were employed. Meyer's Analysis of Ball Indentation Test The ball indentation test is probably the most valuable hardness test we now have but, as it is carried out in the Brinell or Rockwell test, the result may be seriously in error without the operator suspecting such to be the case. This condition results from the isolated and uncontrolled nature of the measurement. The accuracy depends on the accuracy of the equipment and the care and skill used in the operations; there is nothing in the impression diameter, which is all that is measured, to indicate the presence of error. Meyer's analysis supplies a control of the measurements that goes far toward eliminating unsuspected errors. The principles of this work may be obtained from elsewhere.' As this subject has not received the attention of this Institute, it may be well to summarize the more important points as follows. The chief difference between the usual ball indentation hardness test and Meyer's test is the use of a number of loads, instead of one, covering the range from small to large loads. The reason for this may not be obvious; the resistance to penetration may, and generally does, vary with the penetration of the ball; consequently a single determination can give only the resistance at that particular load. At some other load, the resistance may be quite different. For example, a test on annealed copper at 250 kg. gave a resistance to penetration of 39.5 kg. per sq. mm., while a similar test at 3000 kg. gave a resistance of 56.8 kg. per sq. mm. For the purpose of finding some figure that might be used to represent the hardness of the sample of copper, there is no reason for selecting one of

Jan 1, 1926

By P. W. Bridgman

IT is characteristic of most scientific investigators that they are not satisfied with the discovery of new facts, no matter how curious or unexpected, but that along with the factual discovery there is a constant effort to understand It appears that. one's interest in, and satisfaction with, the discovery of an array of news experimental facts is enormously increased if one has at the same time a theory or hypothesis guiding one's expectation of what sort of new experimental discovery may lie around the corner Conversely, as a theoretical physicist one's satisfaction with his theory is greatly enhanced if along with the development of the theory can go the discovery of new experimental facts, confirming or perhaps modifying the theory as it grows Of course, there have been long and stretches in the history of physics in which new data of unquestioned ultimate importance ham e piled up, without much inspiration or illumination in the way of understanding For 50 years spectroscopy had such an and history, but how irksome this was felt to be is plainly shown by the almost audible relief that greeted the first success by Bohr in injecting understanding into the situation, and by the fresh rush of experimenters into this field when the prospect of understanding had once been offered The investigations in the field of high pressure, which have occupied me for a long time,1 until the last few years have been in very much the Same sort of situation as spectroscopy before the advent of Bohr A great many kids, of data were collected for a great many solid and liquid substances, and there could be no question of the importance of these data, because the uniform change of dimensions produced by hydrostatic pressure is perhaps the simplest conceivable type of alteration to which a body can be subjected But except for a few isolated flashes, there was no theoretical illumination, so that it had to be to a large extent the enthusiasm of the collector that kept me going However, within the last few years the wave-mechanics theory of solids has progressed so rapidly that

Jan 1, 1938

By G. F. Comstock

A serious disagreement as to the effect of titanium on the hardenability of steel exists in published references to this subject. Kramer, Hafner and Toleman reported' that acid-soluble titanium decreased creased the hardenability, with multiplying factors less than unity according to [ ] Grossmann's system for calculating hardenability from the composition. Crafts and Lamont, on the other hand, showed2 how titanium increased the hardenability, with multiplying factors up to nearly 1.7 for about o.' per cent titanium, though reducing the hardenability with higher titanium. Their data, however, were obtained almost exclusively from steels containing more than 2.4 per cent manganese, and thus should be considered as applying mainly to manganese steels. Likewise, the results of Kramer, Hafner and, Toleman regarding titanium are subject to the limitation that although they eliminated the effect of the insoluble titanium compounds from their calculations, they did not make a similar correction for the carbon that was combined with titanium and therefore occurred in a similarly ineffective form. It is suggested by the literature referred to that titanium may have different effects on hardenability, depending on the mode of its occurrence in the steel. The different effects on strength, ductility, etc., have already been discussed by the author.3 In the present discussion some comparisons, on the basis of hardenability as revealed by the Jominy end-quench test, are given between three titanium and two non titanium steels heat-treated in the same ways, and between other titanium steels heat-treated in several different ways. COMPARISON OF PLAIN-CARBON, VANADIUM AND TITANIUM STEELS The five steels used for these experiments were commercially melted and rolled products received in the form of 1.5-in. rounds from three different mills. Their analyses are given in Table I. Steels 2, 3, and 4 are from the same basic electric heat, containing 0.009 per cent of phosphorus and the same amount of sulphur. They were made by, adding aluminum and low-carbon ferrotitanium to different ingots. No. I is a plain-carbon coarse-grained S.A.E. 1040 steel made by the basic open-hearth -process. No. 5

Jan 1, 1945

By Raymond Mancha

The number of installations of propeller mine fans completed during the years of 1936 and 1937 is evidence of the increasing popularity of the propeller fan with the American mining industry. During the period from 1931 to 1936, there were several different low-pressure, low-efficiency propeller fans available, which filled a definite need in replacing inefficient centrifugal fans operated at comparatively low pressure by means of purchased power. Since 1936, however, the trend toward the propeller fan has greatly increased, as propeller fans are now available practically without pressure limitations and capable of efficiencies high enough to warrant replacement of efficient centrifugal fans in many instances. Few manufacturers of propeller mine fans base their fan-operating characteristics upon similar test methods, primarily because of inadequate facilities for testing in the factory and the need of a test code incorporating a calibrated duct or nozzle that makes possible the testing of large propeller fans quickly, accurately and without prohibitive expense and space requirements. As a result, fan manufacturers have resorted to various methods for testing large propeller fans in the factory, and different yardsticks have produced uncomparable and often inaccurate performance data. It is the purpose of this paper to describe and discuss in detail the test procedure of the Jeffrey Manufacturing Co., which has been proved both accurate and practical. Fig. 1 shows a plan, a side elevation and two end elevations of the test duct with a propeller fan of the exhaust type in place. Testing propeller fans exhausting permits greater accuracy than testing these fans blowing, because in the former uniform flow conditions are more easily established at Pitot tube stations where fan pressure and air-volume measurements are desired. Any residual rotation remaining in the air discharged from a propeller fan blowing into a test duct must be removed before an attempt is made to obtain accurate pressure and volume readings. Although various devices for straightening the air may be placed between the blowing fan and the volume-measuring station without resulting complications, uniform flow so obtained at the pressure-measuring station necessitates corrective calculations to compensate for duct resistance

Jan 1, 1940

By W. A. Tiller

SEVERAL authors1-6 have shown that, during solidification from the melt, the direction of formation of substructure boundaries depends upon the direction of heat flow and the rate of solidification of the metal. The most prominent of these observations was that a preferred orientation developed during the solidification of the columnar zone of an ingot which for face-centered-cubic metals was the <100> direction. Previous explanations1-&apos; given to account for this preferred orientation and the other boundary phenomena are all based on the premise that the phenomena are characteristics of the pure element. However, recent experiments by Rosenberg and Tiller7 have demonstrated that the preferred orientation in pure lead is the <111> orientation, and that the heretofore observed <100> orientation is due to the effect of solute on the mode of solidification of the metal. Teghtsoonian and Chalmers,4 studying striation boundaries in tin, and Chalmers and Rutter,5 studying corrugation boundaries in tin, showed that these substructure boundaries were aligned parallel to the axis of heat flow for slow rates of growth, and that the alignment varied from this direction as a function of the rate of growth. to approach the den-drite direction at high rates. Chalmers,6 studying the direction of formation of a grain boundary separating two crystals of different orientation, showed that at slow growth rates the boundary is parallel to the axis of heat flow, while at higher speeds it will deviate from this direction, sloping into the crystal whose dendrite orientation departs the most from the axis of heat flow. It is this phenomenon that allows certain crystallites in the chill zone region of an ingot to encroach on their neighbors and ultimately produce the preferred orientation of the columnar zone of the ingot. Since the previous explanations of this preferred orientation are unable to account for the recent observations,&apos; a new mechanism will be considered. This will lead to an explanation of the other substructure boundary phenomena as well. Investigations by Graf,8 Billig,9 Rsenberg,10 and others have demonstrated in a striking fashion that crystal growth takes place by the deposition of individual layers oriented along the close-packed planes of the material considered. This lamellar or

Jan 1, 1958

By H. D. Hibbard

At the beginning of a Henry M. Howe lecture it seems fitting to refer to Howe&apos;s great contributions to steel metallurgy, and particularly to the literature thereof. Most of my predecessors in this role have been able, from their association with him, to give direct testimony as to his great services; but although connected with him for years in a business way, I am less familiar with what might be called his academic side, except as it is embodied in his utterances, written and oral. Howe was adept in his genial way in extracting information in any line which, at the time, was of interest to him. In a technical lecture one expects as a rule new knowledge-—something about recent advances relating to the subject. On this occasion, however, I will ask you to go back with me to the primary department of steel lore, as the title of my lecture shows, to review the more fundamental features in that field for the purpose of seeking some gaps which we can fill and so give the subject renewed interest. In thus going back one must inevitably repeat many familiar facts, but that seems to be necessary in order to reach a clear understanding of the unrecorded matters. The full interpretation of a steel analysis is at present unattainable, though much progress toward that end has been made. The ultimate analysis, giving the percentages of the five commonly determined elements, does indeed usually give a fair idea of what the steel is, and is ordinarily enough, with knowledge of its history and physical condition, to enable it to be assigned to some purpose or use for which it is reasonably suitable. Rut discrepancies arise. Every maker and every User of steel knows, from at least occasional examples in his own experience, that the ultimate analysis is insufficient by itself to enable one to tell positively, from its interpretation, either the mechanical properties of the steel or its adaptability to the purpose for which it was made. Further, if, while having the specified composition, it is abnormal or unsatisfactory, why it is so. Good, bad and indifferent steels may have substantially the same ultimate analysis.

Jan 1, 1928

By Joseph A. Norden, A. R. Willson

Much has been written concerning the hoisting equipment of various mines throughout the country, but most of the literature on the subject, if not all, describes equipment of extraordinary capacity and the small and medium-sized outfits have been neglected. The hoisting equipment here described is capable of handling about 1200 tons per day. It has not been worked to capacity, but 600 to 700 tons, together with men and materials, have been handled in two shifts without any great effort. Only one shaft extends from the surface to the lowest levels of the mine; see Fig. I. It is composed of three compartments, two of which are used for hoisting, and the third for water, air, and electrical lines, and for sinking purposes. In 1909, this shaft was raised from the 1000-ft. (304-m.) level to the 700-ft. There a station was cut and an air hoist installed. At this time all mining operations were confined to the upper levels of the mine; that is, above the 700-ft. The ore was dropped to this level through chutes from the 300-, 400-, 500-, and 600-ft. levels and then lowered in cars on cages to the 1000-ft., which is the main haulage adit, the mill and railroad bins being about 3000 ft. from the shaft. Orebodies were, in due time, developed on the 1000-ft. level and below. Therefore, in 1913,the shaft was sunk to the 1150-ft. level and thereafter sinking was continued at regular intervals until the 1500-ft. level was reached. But, hoisting from the 1300-ft. level was a difficult and slow process with the antiquated air hoist, so, in 1916, it was decided to raise the shaft to the surface and install a modern, electrically operated hoist. This was completed early in 1917 and the hoist was in operation in March of that year. The Hoist Figs. 2, 3, and 4 show various features of the hoist and electrical equipment. A Nordberg engine of the double-drum, geared type, designed for a 10-ton load, including rope, at a speed of 1500 ft. per min., is used. The drums are 7 ft. (2.1 m.) in diameter, with a 54-in. (137-em.)

Jan 1, 1922

By Arthur J. Boynton

In the preparation of this paper the writer has been influenced by the fact that descriptions of various means of cleaning blast-furnace gas have been published and that further descriptive treatment of the subject will probably be less interesting than a statement of conclusions with regard to preferable methods which have been reached by him as a result of experience and observation in this country and also as a result of somewhat detailed investigation of the subject made toward the end of the year 1927 on the Continent of Europe and particularly in Germany. Owing to various circumstances, including a cost of fuel that is extremely high in relation to the wages of labor, the German iron and steel industry has accumulated experience in gas washing which is as yet in part lacking in the United States of America. The paper begins with a statement regarding the economics of the use of blast-furnace gas, then considers the principles and practices employed in its purification. Uses of Blast-furnace Gas For many reasons having to do with the utilization of coke-oven and blast-furnace gases in steel manufacture and with the use of hot metal, the blast furnace is now usually a part of a steel-producing unit, which also includes coke plant and rolling mill. Therefore both blast-furnace and coke-oven gas are usually applicable to any of the iron and steel-making processes, including the generation of power, and their allocation in any given works should be considered as a single problem. The uses to which blast-furnace gas, either alone or mixed with coke-oven gas may be put, include the following: Regenerative Heating of Ail. for the Blast Furnace.—This is the oldest and metallurgically the rnost important of all uses. It is universally performed with unmixed blast-furnace gas and under proper conditions should require not over 23.5 per cent. of the total gas generated for a blast temperature of 1350" F. For Steam-raising Purposes.—This is almost universally done with unmixed blast-furnace gas. From the standpoint of quantity used, it is at the present time the most important application in American steelworks practice.

By C. S. Sivil

To modern civilization the platinum metals are of inestimable value. Their distinctive properties, both physical and chemical, render them indispensable in an age in which the processes of the laboratory are becoming an essential part of the daily life of the world. Generally, their function, though vital to particular processes, is not spectacular, and so remains unknown to all except the operators. Early Methods of Manufacture The properties of platinum were recognized as of prime importance for scientific work at a very early date, probably between 1750 and 1760. The difficulty of making articles from it seemed almost insurmountable, because no means of attaining the temperature necessary to melt it were known at that time. It is true that solid platinum could be obtained by fusing the metal with a more volatile metal such as arsenic, which was subsequently driven off by baking, but such a method, at its best, would give only a very brittle product, which was totally unsuitable for the purposes for which it was intended. Little, if any, progress could be made until it was discovered that platinum sponge, heated to white heat and hammered in an iron or clay mold, would metallize and retain the shape of the mold. This was a process that could not be wholly satisfactory but from it developed the method of pressing the sponge in a mold and forging it at white heat into wire or sheet. At present a somewhat similar process must be used for fabricating articles of tungsten, molybdenum and other metals of high fusing point, as with these metals we face today the same problems that the scientists of the eighteenth century encountered with platinum, but possibly the next significant advance in the metallurgy of these metals will be the devising of means to melt and cast them. TO some extent this method of preparing platinum has survived, particularly in Europe. There are one or two objections to it, but they are not serious, as they can be surmounted with proper precautions. In the first place, the material is spongy and its millions of cavities contain entrapped air. Unless this is removed by thorough forging above 1000" C. the resultant sheet shows blisters. To give such a thorough forging,

Jan 1, 1931

THE composition and quality of finished steel depend upon selection and proportioning of the raw materials of the charge as well as upon control of furnace practice. This chapter deals only with the raw materials of the basic open-hearth process that are important in determining the composition of the steel or slay. They are the metallic charge, oxygen-bearing materials, fluxes, alloying and deoxidizing additions, and certain refractory materials used for maintenance of bottoms. Other refractories, which may affect the slag composition, are discussed in Chapter 3. Wide variations are possible in the type and composition of charged materials but certain limiting relations among the elements of the charge must be observed. Since the process consists essentially of refining by the oxidation of undesired elements, a balance must be established between the sources of oxygen and the elements in the charge that are subject to oxidation (see Chapters 2 and 7). For example, if it is desired to use a high ratio of blast-furnace hot metal to scrap, it is necessary to add an oxygen-bearing material such as ore or mill scale to eliminate the excess carbon and silicon that are present in the hot metal. An example of the opposite extreme is the use of a metallic charge composed entirely of steel scrap. With this type of charge, it is common practice to substitute burnt lime for limestone as a flux and to charge some carbonaceous material such as coke to avoid an excess of oxygen in relation to the elements of the charge that are subject to oxidation. Elements such as copper and nickel, which are not oxidized or eliminated by any other reaction, may be introduced into the charge only to the extent to which they are permissible in the finished steel. An example of adjustment of the charge for elements of this type is found in the use of steel scrap high in copper. In this case, metallic components of the charge other than the scrap should be low in copper, or a sufficiently high ratio, of pig iron to scrap should be charged to dilute the copper from the

Jan 1, 1964