Search Documents

THE composition and quality of finished steel depend upon selection and proportioning of the raw materials of the charge as well as upon control of furnace practice. This chapter deals only with the raw materials of the basic open-hearth process that are important in determining the composition of the steel or slag. They are the metallic charge, oxygen-bearing materials, fluxes, alloying and deoxidizing additions, and certain refractory materials used for maintenance of bottoms. Other refractories, which may affect the slag composition, are discussed in Chapter 3. Wide variations are possible in the type and composition of charged materials but certain limiting relations among the elements of the charge must be observed. Since the process consists essentially of refining by the oxidation of undesired dements, a balance must be established between the sources of oxygen and the elements in the charge that are subject to oxidation (see Chapters 2 and 7). For example, if it is desired to use a high ratio of blast-furnace hot metal to scrap, it is necessary to add an oxygen-bearing material such as ore or mill scale to eliminate the excess carbon and silicon that are present in the hot metal. An example of the opposite extreme is the use of a metallic charge composed entirely of steel scrap. With this type of charge, it is common practice to substitute burnt lime for limestone as a flux and to charge some carbonaceous material such as coke to avoid an excess of oxygen in relation to the elements of the charge that are subject to oxidation. Elements such as copper and nickel, which are not oxidized or eliminated by, any other reaction, may be introduced into the charge only to the extent to which they are permissible in the finished steel. An example of adjustment of the charge for elements of this type is found in the use of steel scrap high in copper. In this case, metallic components of the charge other than the scrap should be low in copper, or a sufficiently high ratio of pig iron to scrap should be charged to dilute the copper from the

Jan 1, 1951

By L. C. Raymond

Valuations in the mineral industry differ from those of other enterprises because mines and oil wells have a definitive life so cannot be considered a perpetuity. This requires that in any mineral-property evaluation the recovery of invested capital is necessary during the life of the property. Capital writeoffs for nonextractive industries are assumed to be continuously plowed back to sustain the operation and produce yields on the capital invested. The extractive or mineral industry, however, generally attempts to return to the investor both interest and principal during the life of a property. Normally this is done currently and the dividend includes both items. Where the mineral properly possesses large reserves and the life factor approximates a perpetuity, the return on investment is generally comparable to that of industrial stocks. The valuation of a mineral property, at best, is based on educated estimates and judgment factors. This is particularly true as it relates to estimating selling prices over a long term or assessing the quality of management. Also, it is possible to make various assumptions as to rapidity of working out the deposit, varying time for start-up of operations, varying earning rates, so as to obtain different results with the same basic facts. Thus it is not surprising that two engineers, irrespective of their abilities, may not agree exactly even when given the same facts, but their results should be close enough to be used in establishing a fair value for trading purposes. The valuation is no better than the source of basic data and the soundness of judgment factors. Fundamentally the basic principles of mineral valuation are similar for base metals, sulphur, oil, or any other mineral. Each mineral, however, requires an engineer to have a knowledge of such factors as its occurrence, distribution, mining and processing methods, and marketing problems in order to gather and analyze all the facts and data that have a bearing on the earning potential of the property. PRESENTVALUEOFAMINERALPROPERTY In essence the present value of a mineral property is a sum of money in today's dollars that future earnings from the property are worth. It differs

Jan 1, 1959

By D. A. Woodford

In a constant-load creep test, if the density of nlobile dislocations is assumed constant for strains exceeding that corvesponding to the minimum creep rate, it is shown that the creep rate may be approximated by the equation where E is the nominal strain, o0. is the initial stress, and a' the stress fov unit dislocation velocity. The constant C contains the mean density of mobile dislocations and n is a measure of the stress sensitivity of dislocation celocity. This equation is shoum to be applicable to published data on an alloy steel and on nickel. The degree of plastic instability and hence the creep ductility is dependent on the calue of n for these materials. When instability becomes gross and local macroscopic necking occurs, the assumptions are no longer valid. On the basis of this equation, and the strain-time relation derived from it, a method of predicting the creep behavior at different stresses is suggested. MOst analyses of creep data have been concerned with time-dependent transient creep or time-independ- ent secondary creep in constant-stress tests. The far more widely used constant-load test has been neglected in terms of a mechanistic approach. In general, since the strains involved are usually small, the same laws for transient creep may be applied to both types of tests. However, there is no steady-state creep in a constant-load test since the stress increases continuously. Any apparent steady state observed on a strain-time plot is either fortuitous or illusory, and is generally revealed as a continuously varying creep rate on a carefully constructed strain rate vs time plot.* Transient creep may be understood in terms of a simple differential equation representing the change in mobile dislocation density with time:' where p is the density of mobile dislocations. The first term on the right is related to first-order kinetics of dislocation multiDlication and the second to second-order kinetics of exhaustion. On the basis of this equation, several authors2-4 have found good agreement with experimental transient creep curves for a number of materials. When k1p = k2p2, a steady-state creep

Jan 1, 1968

By Ernest F. Burchard

A reconnaissance of the chrome and manganesel ore deposits of Cuba was made in the spring of 1918 by Albert Burch, representative of the U. S. Bureau of Mines, and the writer, representing the U. S. Geological Survey. The object of the study was to obtain authentic information for use of the United States Government as to the location, character, size, and availability of the Cuban deposits of the ores of these important steel-alloy metals. The Cuban Government courteously detailed Sr. E. I. Montoulieu, a mining engineer connected with the Treasury Department, to act as escort and associate throughout the work on the Island. Mr. George A. Wright, of Baracoa, Cuba, a minirng engineer especially familiar with the chromite deposits of Oriente Province, was a member of the party from Feb. 25 to Mar. 20. It was possible to visit most of the chrome-ore deposits that seemed to be of promise, but there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Furthermore, no attempt was made to examine the extensive chromiferous iron-ore deposits of the Mayari, Moa, and Cubitas districts, as these deposits cannot be regarded as sources of chromium except indirectly. At the close of the field work the essential data concerning the quantity and quality of ore probably available for shipment during 1918 and 1919, in the event of the continuation of the European war, and of the tonnage of ore in reserve, were furnished to such Government bureaus as were interested, including the Shipping Board and the War lndustries Board, and as soon as chemical analyses of the chrome ores could be obtained, a press bulletin on the subject was published by the Geological Survey. In the present paper the engineering data and tonnage estimates contained in the unpublished notes of Mr. Burch have been freely used, and their helpfulness is hereby gratefully acknowledged. Many thanks are due Senor Montoulieu and Mr. Wright for their valuable work in the field; to the officials of the Spanish American Iron Co. and of the various other companies; and to individuals holding chromite claims, for courteously facilitating the work of the party.

Jan 1, 1920

By L. C. Raymond

Valuations in the mineral industry differ from those of other enterprises because mines and oil wells have a definite life so cannot be considered a perpetuity. This requires that in any mineral-property evaluation the recovery of invested capital is necessary during the life of the property. Capital writeoffs for nonextractive industries are assumed to be continuously plowed back to sustain the operation and produce yields on the capital invested. The extractive or mineral industry, however, generally attempts to return to the investor both interest and principal during the life of a property. Normally this is done currently and the dividend includes both items. Where the mineral properly possesses large reserves and the life factor approximates a perpetuity, the return on investment is generally comparable to that of industrial stocks. The valuation of a mineral property, at best, is based on educated estimates and judgment factors. This is particularly true as it relates to estimating selling prices over a long term or assessing the quality of management. Also, it is possible to make various assumptions as to rapidity of working out the deposit, varying time for start-up of operations, varying earning rates, so as to obtain different results with the same basic facts. Thus it is not surprising that two engineers, irrespective of their abilities, may not agree exactly even when given the same facts, but their results should be close enough to be used in establishing a fair value for trading purposes. The valuation is no better than the source of basic data and the soundness of judgment factors. Fundamentally the basic principles of mineral valuation are similar for base metals, sulphur, oil, or any other mineral. Each mineral, however, requires an engineer to have a knowledge of such factors as its occurrence, distribution, mining and processing methods, and marketing problems in order to gather and analyze all the facts and data that have a bearing on the earning potential of the property. PRESENT VALUE OF A MINERAL PROPERTY In essence the present value of a mineral property is a sum of money in today's dollars that future earnings from the property are worth. It differs

Jan 1, 1964

By Walter Rosenhain

In selecting solid solutions for the subject of this lecture I have been guided by several considerations. The bodies known under that somewhat paradoxical name play a most important part in all types of alloys; consequently, a deeper knowledge of their constitution must 'be of fundamental importance to both metallurgical science and practice. Further, having been asked to deal with some of the more theoretical aspects of metallurgy, I have been tempted to describe certain considerations, which I believe to be novel, in regard to the nature of solid solutions. These considerations constitute a theory that requires much experimental confirmation, but they have passed the stage of speculations, for experimental evidence has become available and one inference after another, that can be derived from the theory, is found to be in accord with well-known facts. In putting before you these ideas and inferences, it must be understood that detailed quantitative proof of every step cannot be furnished. Our conclusions must therefore be stated with the reservation that their acceptance must depend on the manner in which the discovery of fresh facts may either confirm or confound them. If we wish to understand the structure of solid solutions we nust carefully realize the manner in which these bodies are formed in alloys. The formation of solid solutions is by no means confined to alloys, but it is desirable to confin5 attention, at the outset, to intermetallic solid solutions. It is not easy to formulate a precise definition of the term "solid solution." It may be said that a solid solution is a crystalline body formed from a liquid solution or from an intimate mixture of solids, or of liquid and solid, that retains in the solid state an admixture of the two substances (solvent and solute) as intimate as that which exists in a liquid solution. The term is undoubtedly paradoxical, for one usually associates solution with a liquid, but the difficulty cannot be evaded by using such a term as solidified solution, for this might refer to a solution that has set, or congealed, without undergoing crystallization. The German term mischkry stall avoids the difficulty and appears to

Jan 1, 1923

By John T. Norton, R. E. Hiller

The tremendous increase in the use of metals that have been prcpared by the various cold-working processes during recent years has greatly stimulated the investigation of problems concerned with the fundamental nature of these processes. It has been observed in practice that different methods of bringing about the same dimension changes in a sample result in a rather wide range of properties. Cold working reduces the ductility of a metal, or what is perhaps more nearly correct, its "working capacity," and naturally the manufacturer wishes to produce an article that has as large a working capacity as possible, and to produce it with the smallest number of operations. It has also been known for some time that cold deformation produces a parallel alignment of the crystal grains of a metal, and that the type of this preferred orientation depends to some extent at least upon particular processes employed in the deformation. The present investigation has for its purpose the study of the relations between the various factors of a cold-working process and the preferred orientation of the metjal crystals resulting from this deformation. The work is chiefly confined to a study of cold-drawn seamless tubing. Preparation of Samples The tubing samples used in this investigation were made of steel having a carbon content of 0.10 to 0.20 per cent, and were drawn on a standard type of draw bench. In order to obtain the large reductions, the annealed stock was coated with lead, for purposes of lubrication. The reductions of area stated refer to reduction from the annealed condition without intermediate heat treatment. The cold work was done as nearly as possible at room temperature. The samples of wire and strip used for purposes of comparison were of steel of approximately the same carbon content and were prepared in the manner indicated. X-ray Method of Investigation The condition of preferred orientation in cold-worked samples is best investigated by the X-ray method that employs a small circular beam of * Assoriate Professor of Physics of Metals, Massachusetts Institute of Technology. t Graduate Student, Department of Metallurgy, Massarhusetts Institute of Technology.

Jan 1, 1932

By Barry D. Lichter, Pierre Sommelet

High-temperature heat contents of InAs and GaAs were measured over the temperature range 400°K to temperatures above the melting points using a di-phenyl ether drop calorimeter. Smoothed values of the thermal properties have been derived and tabulated at even temperature interuals . The heats of fusion of InAs and GaAs were determined as, respectively, 8790 ± 200 and 12,590 ± 300 cal per g-atom at the respective melting points of 1210º ± and 1513º ± 1°K, yielding entropies of fusion of 7.26 * 0.16 and 8.32 ± 0.20 cal perºK per g-atom, respectively. A general discussion of the thermal properties of III-V com-pounds is given. THE low-temperature heat capacities of InAs and GaAs have been determined by Piesbergen.1Using a dynamic temperature modulation technique, Miller2 has determined the heat capacities of the compounds as well as GaSb and Ge between room temperature and 650°K; however, it has been observed that values determined by drop calorimetry for GaSb3 and for germanium4 are consistently about 5 pct lower than Miller's results. Cox and Pool10 report values for the heat content of InAs and GaAs and the heat of fusion of InAs. No value for the heat of fusion of GaAs appears to have been previously reported. This paper reports results of high-temperature heat content investigations of InAs and GaAs measured in the range 400" to above 1500°K employing a diphenyl ether drop calorimeter. These results, together with our previous results on III-Sb compounds3 as well as heat-content measurements5 of solid InP and Gap, are used in a general discussion of these compounds. EXPERIMENTAL PROCEDURES High-purity samples of the compounds, stoichio-metric to ±0.1 at. pct, were supplied in the form of crushed crystal fragments by Dr. Carl Thurmond of the Bell Telephone Laboratories. The sample preparation, description of the calorimeter, and details of the heat content measurement have been previously described.3 Samples were sealed in evacuated silica capsules and suspended by a Pt-Rh wire in a Pt-wound vertical tube furnace, heated to temperature

Jan 1, 1970

By Walter Rosenhain

In selecting solid solutions for the subject of this lecture I have been guided by several considerations. The bodies known under that somewhat paradoxical name play a most important part in all types of alloys; consequently, a deeper knowledge of their constitution must 'be of fundamental importance to both metallurgical science and practice. Further, having been asked to deal with some of the more theoretical aspects of metallurgy, I have been tempted to describe certain considerations, which I believe to be novel, in regard to the nature of solid solutions. These considerations constitute a theory that requires much experimental confirmation, but they have passed the stage of speculations, for experimental evidence has become available and one inference after another, that can be derived from the theory, is found to be in accord with well-known facts. In putting before you these ideas and inferences, it must be understood that detailed quantitative proof of every step cannot be furnished. Our conclusions must therefore be stated with the reservation that their acceptance must depend on the manner in which the discovery of fresh facts may either confirm or confound them. If we wish to understand the structure of solid solutions we nust carefully realize the manner in which these bodies are formed in alloys. The formation of solid solutions is by no means confined to alloys, but it is desirable to confin5 attention, at the outset, to intermetallic solid solutions. It is not easy to formulate a precise definition of the term "solid solution." It may be said that a solid solution is a crystalline body formed from a liquid solution or from an intimate mixture of solids, or of liquid and solid, that retains in the solid state an admixture of the two substances (solvent and solute) as intimate as that which exists in a liquid solution. The term is undoubtedly paradoxical, for one usually associates solution with a liquid, but the difficulty cannot be evaded by using such a term as solidified solution, for this might refer to a solution that has set, or congealed, without undergoing crystallization. The German term mischkry stall avoids the difficulty and appears to

Jan 1, 1923

By P. V. Faragher

A metal or alloy finds its place in commerce in proportion to its ability to serve certain purposes better and more economically than other materials. While there is some overlapping of the fields of application of the various metals under discussion in this symposium, each one has its uses for which it is especially adapted. While aluminum is the most recent of the metals to enter the field, the development of the industry has been based on its peculiar properties, by virtue of which new uses for non-ferrous metals have been created. There has been substitution of this new metal for other members of the group but there has been a far greater development in entirely new fields. In common with the other non-ferrous metals, aluminum is resistant to atmospheric corrosion. It also withstands the action of many of the common chemical reagents, strongly alkaline substances being the notable exceptions. The outstanding properties on which the application of aluminum is based are its low specific gravity and its ease of fabrication into the forms in which it is used. It is noteworthy that this property of specific lightness is retained in all the commercial aluminum-base alloys. This statement does not apply to aluminum bronze; this is more properly a copper-base alloy, since aluminum enters into its composition to the extent of only about 10 per cent. None of the commercial casting alloys of aluminum has a density exceeding that of the parent metal by more than about 10 per cent., and some are actually lighter. In the so-called "strong alloys" of aluminum in which strengths comparable to that of mild steel are developed by heat treatment, the greatest increase in density is only slightly more than 3 per cent., and one of these, also, is lighter than aluminum. This property of lightness combined with the desirable mechanical properties of the alloys, makes aluminum especially suited for parts of moving assemblies where saving in power, as well as a decrease in stresses resulting from inertia and vibration, are of importance.

By Hans Lundberg

By electrical prospecting, orebodies that do not otherwise manifest themselves at the surface may be located. Conditions favorable to success with the methods are: Favorable geological conditions, such a proportion of minerals of good electrical conductivity in the orebody as will render the latter materially a better conductor than the enclosing rock, situation of the orebody within the range of influence of the electrical currents used and in proportion to this range a sufficient area of horizontal cross section of the orebody. The result is to permit of spotting drill holes accurately and to save the expense of drilling barren ground. THE art of prospecting, like other branches of mining, has developed rapidly during the last ten years, mainly because of the advancement of mining geology, but also because of the development of "geophysical methods," which are based on the different physical characters of minerals and rocks, e. g., specific gravity, elasticity, and magnetic and electric properties. These methods have proved of great value, especially in countries where the rock is covered by soil and direct geologic investigation is out of the question. In prospecting for orebodies, the methods based on studying differences in electrical conductivity have proved most successful; for which reason, the methods of electrical prospecting have been subject to the most energetic and systematic work, especially in Sweden. This paper gives a brief description of the methods of electrical prospecting now in use, especially the new electromagnetic methods, which have not been described before. The great differences in the electrical properties, especially in conductivity, between ore minerals and rock minerals are fundamental to all methods of electrical prospecting, for which reason, the electrical conductivity of ore minerals and rock minerals has been carefully studied in connection with and previous to the development of the various methods of prospecting with electricity. Ore minerals with a metallic luster, such as chalcopyrite, iron pyrite, galena, specular iron, magnetite, etc., also graphite and a number of cows, have considerably higher conductivity than the surrounding rock and soil (see Table 1). The figures of the table denote the specific resistance W, expressed in ohms for a cube with an edge of 1 centimeter.

Jan 7, 1925

By H. S. Greismer

Alabama washes a larger percentage of its total coal output than any state in the Union. For producing coking coal, three-compartment jigs are favored; mines providing, steam and commercial coal use single-compartment jigs exclusively. Chemists are as necessary to washing plants as recording gages are to power plants. Experiments in Alabama indicate that the sludge released by coal-washing plants can be deposited in streams and on agricultural lands without disastrous results. CAMPBELL, 1 in 1896 said: "The Birmingham district in Alabama has certain great advantages for there are few places in the world where fuel and ore are so near together, although, unfortunately, both are of inferior quality; the ore being low in iron and high in phosphorus and the coal giving a weak and impure coke." This statement could not have been, questioned in 1894, but by 1896 several Robinson-Ramsay washers had been put into operation and weak and impure coke was a thing of the past. The Warrior coal field of Alabama contains six seams that yield coking coal of excellent quality. In descending- order, they are Brookwood, Milldale, Pratt, America, Mary Lee, and Black Creek. In each of these, however, bands of rock and bone coal of varying thickness are stratified with the coal; and while some of these impurities can be separated from the coal by the miner, much of it must be loaded out with the coal: Consequently, unless the coal is washed before being coked, it will yield a coke of varying ash and sulfur content quite unsatisfactory, for blast-furnace use. At present, the Gulf States Steel Co. is producing run-of-mine coal at its Virginia mine, from the America seam, that is uniformly low enough in ash to permit of coking without washing, but this is the only exception to the above statement. Alabama was the first state to experiment seriously with coal washers, was the first to install washers on a large scale and, up to the present, has maintained the lead. The Alabama State Mine Inspector reports that during 1923 20,919,303 tons of bituminous coal were mined in Alabama; 12,858,499 tons of which were delivered to coal washers for treatment.

Jan 9, 1924

By G. B. Craig, B. Ramaswami

The temperature and strain rate dependence of the flow stress ratio and the stvain rate dependence qi the flow stress of annealed polycrystalline a zirconiur were determined over the temperature range 30 0" to 1000°K. Some evidence was found for strain aging and discontinuous flow in the temperature ranges 520" to 650°Kand650" to 760°K, respectively. The Cottvell-Stokes relationship was obtained when deformation occurred by twinning as well as slip. The flow stress ratio showed a strong dependence on temperature and strain rate above 800°K. The expevirnental evidence indicated that the rate-controllitzg mechanism for the deformation of a zirconium above 800°K was dislocation climb, and that the deformation was not thermally activated in the range 520" to 800°K. The stacking-fault energy of a zirconium was estimated to be about 250 ergs per sq cm. A knowledge of the temperature and strain rate dependence of the applied stress necessary to deform a crystalline solid is essential for understanding the thermally activated processes occurring during deformation.' Several experimental techniques have been developed for studying these processes.273 One of the techniques is the deter mi nation of the strain rate dependence of the flow stress at constant temperature. In close-packed crystals, it has often been observed that the change in stress due to a change in the strain rate varies linearly with the flow stress, (~1,' This relationship, known as the Cottre ll-Stokes law, is obeyed when deformation occurs by glide alone. However, when deformation occurs by twinning as well as glide, there is disagreement among different investigators on whether the Cottrell-Stokes law is observed. Whereas Thornton et ~1.~find departures from Cottrell-Stokes law when twinning occurs in copper, ~avis~ and sasinski? find that Cottrell-Stokes law is obeyed when deformation occurs by twinning as well as slip in cadmium and magnesium, respectively. One of the main objectives of this study is to determine whether the Cottrell-Stokes law is obeyed when deformation occurs by twinning as well as slip. The second technique that has been used extensively to study the thermally activated deformation of crystals is the determination of the ratio of the flow stresses, at identical dislocation structures and con-

Jan 1, 1968

By H. C. Schultz, F. K. Middleton Hunter

Certain local conditions were known to govern in large measure the successful adaptation of liquid-oxygen explosives to the large-scale blasting at Chuquicamata. The wide variation in hardness of the rock at this mine makes necessary the use of several types of explosives. A locally manufactured, relatively cheap black powder is used in blasting the softer waste and capping material, where a thorough displacement breaks the ground sufficiently. Before the introduction of L. 0. X., an ammonia dynamite of about 65 per cent. strength was being used exclusively in the harder underlying orebody, where a strong disruptive as well as a displacement effect is required for breaking the ore. The L. 0. X., as developed for quarry work in the United States, has a practically pure carbon cartridge material, and the explosive has an extremely high rate of detonation, which should therefore cause it to develop usefully its full disruptive effect in hard ground. The individual blasts at Chuquicamata arc large, black-powder shots which dislodge masses of rock averaging 250,000 tons each, and dynamite shots which dislodge masses averaging 80,000 tons each. It was desirable, therefore, to attempt to displace with L. 0. X. the faster, higher-cost ammonia dynamite used in the smaller blasts. It was not considered practical to attempt to displace the low-cost black powder with 1,. 0. X., as estimated costs showed no probable saving if this were accomplished. Since it was desirable to continue shooting relatively large blasts for effective operation, it was recognized that larger storage facilities than had been in use would be needed for the liquid oxygen. Because of the difficulty of transporting and discharging large storage containers of efficient design, the better plan appeared to be storage and discharge of the liquid at the place of manufacture, and transportation of the filled soaking boxes to the blast. Present Liquid-oxygen Plant An experimental unit with a rated capacity of 75 liters per hour was erected during the latter part of the year 1926 to prove the effectiveness of L. 0. X. at this mine, its cost, and possible efficiency of large-scale storage of the liquid. With this experimental unit 200,000 tons of ore

Jan 1, 1928

By P. V. Faragher

A METAL or alloy finds its place in commerce in proportion to its ability to serve certain purposes better and more economically than other materials. While there is some overlapping of the fields of application of the various metals under discussion in this symposium, each one has its uses for which it is especially adapted. While aluminum is the most recent of the metals to enter the field, the development of the industry has been based on its peculiar properties, by virtue of which new uses for non-ferrous metals have been created. There has been substitution of this new metal for other members of the group but there has been a far greater development in entirely new fields. In common with the other non-ferrous metals, aluminum is resistant to atmospheric corrosion. It also withstands the action of many of the common chemical reagents, strongly alkaline substances being the notable exceptions. The outstanding properties on which the application of aluminum is based are its low specific gravity and its ease of fabrication into the forms in which it is used. It is noteworthy that this property of specific lightness is retained in all the commercial aluminum-base alloys. This statement does not apply to aluminum bronze; this is more properly a copper-base alloy, since aluminum enters into its composition to the extent of only about 10 per cent. None of the commercial casting alloys of aluminum has a density exceeding that of the parent metal by more than about 10 per cent., and some are actually lighter. In the so-called "strong alloys" of aluminum in which strengths comparable to that of mild steel are developed by heat treatment, the greatest increase in density is only slightly more than 3 per cent., and one of these, also, is lighter than aluminum. This property of lightness combined with the desirable mechanical properties of the alloys, makes aluminum especially suited for parts of moving assemblies where saving in power, as well as a decrease in stresses resulting from inertia and vibration, are of importance.

Jan 1, 1928

By Shiro Ban-ya, John F. Elliott, John Chipman

The activity of carbon in Fe-C austenite at 1150°C has been determined for concentrations up to about 2.1 pct C using the equilibrium: C + COz = 2CO; equations have been derived expessing the activity as a function of carbon content on the basis of twelve mathematical models. Several of these represent the data satisfactorily. ACCURATE information on the thermodynamic properties of austenite in the binary system Fe-C is needed as a basis for studies of transformation and precipitation in steels of all sorts, alloy as well as plain carbon. The many attempts to approach this problem through statistical thermodynamics require sound and dependable experimental data in order to evaluate the several models which have been suggested. In this paper we are concerned with the experimental determination of the activity-composition relation in austenite at the temperature of its widest range of stability, approximately the eutectic temperature (1153°C). Accurate investigation of the activity of carbon in austenite may be said to have begun with the work of Dunwald and wagner.' A more detailed study was carried out by R. P. smith2 on the two equilibria: More recent work on these two equilibria has been reviewed by Chipman,3 who pointed out the experimental hazards associated with studies of Eq. [I]. Studies of this reaction involve rather small values of the ratio these are susceptible to errors due to traces of moisture in the apparatus according to the reaction: Ellis, Davidson, and Bodsworth4 evaluated K, for their experimental temperatures and used desiccants to control water vapor pressure. While they were able in this way to obtain consistent values for K1 it cannot be said that all of the uncertainties of the method have been overcome. Results by both methods reported by Schurmann, Schmidt, and wagener5 appear to be consistent except at very low carbon content. Reaction [2] was employed in the experimental work reported here. It is to be recognized, however, that it is not applicable to projected studies of certain alloy steel compositions involving stable oxide-formers.

Jan 1, 1970

By A. S. Hewitt

After an interval of fourteen years, saddened for all of us by the death of David Thomas, the father of the anthracite iron-trade, first president of the Institute, and by the untimely loss of his successor, Alexander L. Holley, whose memory we are about to honor by loving services, the members of the American Institute of Mining Engineers have conferred upon me for the second time the office of president, under circumstances similar to those which led to the choice in 1876. Then the whole world was represented at the great exposition of industry which was held in Philadelphia to celebrate the one hundredth anniversary of our declaration of political independence. In 1890 it is our privilege to receive as guests the members of the British Iron and Steel Institute, who, with singular and graceful felicity, have appointed a meeting in the United States in the year when we pass from the second to the first place in the international column of the production of iron, and thus celebrate our industrial independence. For the honor of being chosen to extend to our distinguished guests the right hand of fellowship and a hearty welcome I return to my associates the grateful acknowledgment of one whose chief claim to your favor is to be found in his love for the professional occupation in which we are all engaged, and in his efforts, public and private, to promote its advancement into new fields of usefulness. In order to indicate the full significance of the visit of our foreign guests at this time, it will be proper to explain briefly the origin, aims and work of the Iron and Steel Institute. It unquestionably owes its birth to the International Expositions held in London in 1851 and 1862, and in Paris in 1867. These expositions served to break down the jealousies of nationality and to diffuse a better knowledge of industrial processes. Trade-secrets, which had been carefully guarded, became common property; manufacturers who had previously regarded themselves as rivals formed bonds of union and ties of friendship, as the results of an intercourse which

Jan 1, 1891

By Chas Dobbel

THE Chief Consolidated properties are situated in the Tintic mining district of Utah, being included in Juab and Utah Counties, about 70 miles south of Salt Lake City. The drilling referred to in this paper has been carried on in the Chief Consolidated No. 1 mine, the Gemini mine, and the Eureka Hill mine at Eureka, the Grand Central mine, above Mammoth, and the Apex Standard mine just south of Dividend. The occurrence of ore through the district is typically in lenses on bedding or breaks, and in connecting pipes, without accurate geometrical trend so that the ratio between the total length of development in drifts and crosscuts to the square feet of ore exposed is very high. A section of one of the western channels (Fig. 1) through the Tintic district, shows, roughly, the irregularities calling for excessive development work, so typical of the Tintic mines. This irregular trend of the ore constantly calls for excessive cutting up of the whole area for offshoots and the connecting links always present.. In the planning of prospecting and development, no regular system may be laid out without overlooking some orebodies or segments of orebodies. It was with these facts in mind that Cecil Fitch, the general manager of the Chief Consolidated Mining Co., decided that some method of drilling was the more feasible way of successfully cutting up and bringing about the discovery of ore believed to exist; yet this drilling had to compete with a great. margin of cost over crosscutting, as a crosscut in the Tintic district, even though barren, brings out geologic facts that, in many cases, are worth the price of the working itself. Diamond drills met with the success that might be expected in a district that has a reputation for the wear and loss of diamonds; after 6 or 8 months, this method was discarded on account of the high costs. Simultaneously, a small churn drill outfit was set up underground but a few shifts proved its inapplicability. At the same time, the ordinary hammer drill was usd to drive prospect holes with jointed steel.

Jan 9, 1925

By Victor A. Phillips

A series of specimens of a Cu- 3.23 pct Co alloy were prepared with particle diameters from zero to 590A. The samples were then cold-rolled 95 pct and the effects of the particle size on the behavior on annealing for hr at temperatures between 100" and 900°C were studied (by hardness, light, and electron metallography). Particles, particularly for d r 105 to 590A, greatly impeded softening and vecvystallizn-tion, and tended to give elongated grains. Particles deformed fairly homogeneously with the ,matrix, be- IN a previous study by the author,' the growth of cobalt-rich precipitates was followed electron microscopically in Cu-3.12 Co alloy as a function of aging, typically at 650°C. The coherent spherical precipitates grew to 520 + lOOA average diam before spontaneously losing coherency and developing (111) facets. Stretching a few percent after precipitation 2aused loss of coherency to occur sooner at about 220A average particle diam. The particles apparently retained their fcc structure after loss of coherency. coming lau2ellae. For d = 55 to 180A, these lamellae gave streak-contrast effects apparently due to coherency strains , and spheroidized on annealing at 600" to 650°C, forming coherent particles. Particles of d = 250 ov 320A lost coherency during t-olling, giving incoherent lamellae. Recrystallization apparently occured by growth of new grains into unrecrystallized (recovered) material at temperatures below that at which cobalt atoms had much mobility. The present study was undertaken to explore the effect of cobalt-rjch particles of various average sizes from 50 to 600A diam on the isochronal annealing behavior of copper after heavy cold rolling. The previous work' was used as a guide in preparing the two-phase series of prerolling structures. The solution-treated alloy was also rolled for comparison. A further question of interest in the present study was whether dislocation and particle hardening were additive, since the prerolling structures covered the full range unaged - peak aged — overaged, and further precipitation might occur on annealing after cold rolling. Although there have been exhaustive studies of the isothermal2"6 and is~chronal annealing behavior of

Jan 1, 1967

By A. C. Watts

For several years, a mine in Colorado experienced considerable trouble from small fires caused by the blasting of coal. Although a well-known make of permissible powder was used, it was first thought that the powder ignited gas that might be present and that this, in turn, set fire to line brattices or to the coal. Experiments were, therefore, conducted with another make of powder, but the results convinced the superintendent of the mine, Robt. Williams, Jr., that the fires were not caused by the powder but by the high-voltage electric current used for detonating the shots. The mine "makes" gas very freely, giving off from three-fourths to one million cubic feet of methane every 24 hours. The coal is a good grade bituminous of a very free burning quality. Electric shot-firing from the outside, after all men and animals were outside, had been practiced for a number of years. The shooting circuit was connected with the main power circuit at the mouth of each entry. Shooting circuit switches were mounted in boxes, which were kept locked with the handle of the switch, in open position, showing through the bottom of the box. The door of the box could not be shut and locked when the shooting switch was closed. At the entrance to each room, or working place, a small switch, called the miner's switch, was placed on the shooting line. It was the duty of the miner, when entering his place at the beginning of the shift, to see that this switch was open and that it was kept open until he left the placc at the end of the shift to go out of the mine. Grounded return was used for main power lines. The current was 500 volts, direct current, with 100 to 300 amp. The nearest working face was 9600 ft, from the shot-firers' switch outside the mine and the most remote working face was 2½ miles. The various working faces were scattered over a wide area between these two points. A description of the main power line would be valueless; the conductors were of sufficient size, the drop in voltage being not more than

Jan 1, 1927