Search Documents

By J. P. Martin, A. H. Geisler, J. H. Crede, E. Both

The investigation of a 50 pct Co alloy was undertaken to determine whether there was any direct correlation between the structure and properties of Co-Fe alloys which were given various magnetic heat treatments. The magnetic anisotropy and texture of the 0.002-in. cold-reduced 98 pct material tend to decrease and change in nature with increasing temperature of the recrystallization anneal. Annealing samples in a magnetic field had little effect on either the magnetic properties or texture. However, cooling them in a magnetic field greatly improved their magnetic properties. THE beneficial influence of a magnetic field applied during the heat treatment of certain soft magnetic materials has been known for a long time. Early work showed that the presence of a magnetic field of a few oersteds during the heat treatment of Fe-Ni alloys will cause a large increase in maximum permeability. A pronounced increase in the residual induction which is produced by the magnetic anneal causes the hysteresis loop to approach the shape of a rectangle. Such results are beneficial since the desired properties are high permeability, high induction at maximum permeability, high residual induction, and low coercive force. More recently Libsch and coworkers1 studied the effect of magnetic annealing on the hysteresis properties of a series of Co-Fe alloys prepared from powders. They observed good response for the 35 and 50 pct Co alloys but little response for the 42 pct Co alloy. They pointed out that this was somewhat surprising since the 42 pct alloy has a high linear magnetostriction and zero crystal anisotropy and similar conditions in Fe-Ni alloys give excellent response to magnetic annealing. They found optimum properties to be at the 50 pct composition with residual induction, Br = 19,000 gauss and coercive force, Hc = 0.68 oersteds after the magnetic anneal. Before the magnetic anneal these values were B, = 12,600 gauss and Hc = 1.15 oersteds. The optimum treatment consisted of cooling from above the y-a transformation temperature to 900°C in a field of 20 oersteds, holding 11/2 hr at 900°C, then cooling at a rate of 20° to 25°C per min in the field to below 230°C. Cooling rate mainly affected coercive force with the value decreasing from 1.09 to 0.88 oersteds as the rate was increased from 3° to 48°C per min. Cooling from 1020" to 900°C in a field followed by further cooling to 230°C without the field gave properties decidedly inferior to those for samples annealed with the field applied throughout the cooling. They concluded that to get the best properties the samples must be cooled in a field to a threshold temperature above which the alloy is plastic enough to be affected by magnetostriction. In this respect the holding temperature must be high enough so that the alloy exhibits good plasticity to permit the optimum orienting of magnetic domains by relaxation of magnetostriction. In contrast, the holding time was of less significance for there was little improvement when the time exceeded 1/2 hr. The improvement in properties effected by magnetic annealing has usually been attributed to the establishment of a domain texture caused by the "freezing in" of magnetic strains. On the other hand, Smoluchowski and Turner2,3 apparently found that a magnetic field applied during recrystallization could alter the crystal texture. If this effect is real, improved properties would also be expected when

Jan 1, 1954

By F. G. Miller, T. D. Mueller, L. B. Davidson

A mathematical model of reservoir behavior during one cycle of the intermittent steam injection process is presented in this paper. A cycle of the process is considered to be composed of three stages: injection, condensation and production. The model concentrates on behavior during the production stage. The influence of several parameters on production improvement is described, using the results obtained with a numerical equivalent of the model. Reservoir system parameters considered are thickness, reservoir thermal conductivity, oil viscosity, solution gas-oil ratio and the change in oil effective permeability with temperature. Operating parameters investigated are heat injection rate, steam temperature and cumulative injection time. In the face of considerable uncertainty, the model appears to give a fair prediction of the behavior observed during an actual test. This makes the model a useful means of selecting projects. It is shown that the model may also be utilized to select an optimum set of operating conditions for a particular project. Results of this study show the extent to which production improvement depends on each of the parameters investigated and give an indication of the range of system conditions within which the process would be effective. INTRODUCTION In recent years the intermittent steam injection or steam soak process of oil recovery has become a popular method of improving recovery in reservoirs bearing high-viscosity hydrocarbons. Production improvement due to the process results from heating the reservoir near the wellbore. The process is applied on an individual well basis and is executed in a series of cycles, each consisting of three stages: injection, condensation (the soaking period) and production. During the injection stage, high-pressure steam is injected into the reservoir surrounding the well-bore. This study assumes that injection is carried out over the entire vertical section of the reservoir rock that can be exposed to fluid injection. The condition of steam entering the reservoir is considered to fall within the following limits: (1) steam pressures less than 1,000 psig, (2) steam temperatures between 300 and 700F and (3) steam quality less than 90 percent. The last restriction is due to equipment limitations. Normally, injection re maintained for less than 3 weeks. After termination of injection, the condensation stage begins. The well is shut in for several days, supposedly to make certain that the injected steam condenses. This condensation would insure the retention of injected heat. The production stage is initiated when the well is opened again. Reservoir response during this stage determines the effectiveness of the process (response is defined as the oil production rates, the water production rates and the wellbore temperatures observed during the entire production stage). The immediate response of the reservoir is sometimes quite good. Sets of case histories by Longl and by Owens and Suter2 give some typical figures for response. Duration of the production stage is equal to the time needed for the oil production rate to decline to some predetermined value. This usually requires 4 to 6 months. Termination of the production stage coincides with the start of the next cycle. The process is continued, cycle by cycle, until it becomes unprofitable to continue. One simple model2 and two more sophisticated models3,4 of the process have been presented. These are based on fundamentally different assumptions than those used in this investigation. Although the three models might be modified to fit the assumptions used in this study, it is felt that greater rigor would result by developing a

By W. A. Eardley

FIFTEEN years ago the world's deepest oil well penetrated the earth about 7300 ft. That depth has now been more than doubled. Why has such deep drilling become necessary and how has it become possible? Three factors have had an important bearing: (1) Depletion of shallow zones, making it necessary to search for deeper producing measures. (2) The perfection of prospecting methods, which have been success- fully used to locate favorable buried structures, many at great depth. (3) Improvement in the quality of steels used for drilling.

Jan 1, 1940

By Bernard Schneider

The diversity of methods available to engineers and geologists for studying rock masses is a reflection of the fact that, despite the rapid and encouraging progress made over the last few years, there is still no unified and comprehensive method which can be used to predict the over- all behavior of a foundation. Nevertheless, it is agreed that the fundamental characteristic affecting the engineering properties of rock is fissuration, and this paper de- scribes a few new or improved methods of studying fissuration and its influence on major engineering factors such as permeability, deformability, or internal stresses in the rock volume. TESTS ON SAMPLES Conventional tests on samples using thin slices can be improved by staining the slices before cutting with certain ionic dyes which have an affinity for certain types of surface. This shows up the microdiscontinuities. For example (quoted terms are French trade names) : "Turquoise Motylhne JSA" will show up porous alteration of basic feldspars. "Vert brillant SA" is used for acid feldspars. "Fushine ASA" will show up voids in all rocks. A mixture of "Turquoise" and "Rhodamine BSA" will show up zones of alteration in all types of feldspars. With this technique, it is easy to make an optical classification of the different structural types, e.g.: (1) rocks completely free from voids; (2) rocks with microfissures, which in turn can be subdivided into (a) rocks with microfissures secant to the mineral structure, (b) rocks with microfissures parallel to the mineral structure, and (c) rocks with ran-

Jan 1, 1970

By Donald V. Fites

In the face of an increasing demand for minerals, the resulting technological developments, and rising overburden-to-ore ratios, many open-pit mines now incorporate totally different concepts for the removal of ore and overburden. Moreover, under a growing number of these concepts, wheel tractor scrapers are being assigned a major role in material- handling systems for unconsolidated overburden removal. To say that scrapers move only unconsolidated overburden is incorrect. On the contrary, ripped phosphate rock, copper ore, iron ore, and moderately consolidated overburden are also being moved by scrapers in various areas of the world. According to the Minerals Yearbook, about one half of the material moved in metal and nonmetal mines is never drilled, blasted or broken by other means. Scrapers Find Wider Application The increased use of scrapers in open-pit mining today is due in part to improved design which has endowed these units with added versatility and in- creased their production capability. The modern scraper, which is designed as a loading and hauling vehicle, cannot be compared to the original tractor- drawn scrapers which were limited in capacity, maneuverability, and speed. Improved design of the scraper bowl ejection system has aided production. Gravity ejection has been replaced with positive, forced ejection of material by hydraulic or mechanical action. Bowl and cutting-edge design which allows for maximum load with minimum effort has also increased production. An example of this was the introduction some years ago of the low-silhouette scraper bowl which reduced the work required to lift the material.

Jan 5, 1969

Economic Significance of High-grade Concentrates BY PAUL M TYLER AND CARLE R HAYWARD (Min & Met, Dec, 563 4000 words) Generally pyro¬mctallurgical methods yield a higher recovery but cost more per ton of ore treated Milling methods are inherently cheaper for the reason that they do not involve dissipa¬tion of heat energy in slag formation, ctc It is vaguely realized that the smelter man could do a better job if he were supplied with purer raw materials but hard¬headed mill men have been offered little inducement to do a really good job of cleaning concentrates To do this may involve some sacrifice in percentage yield and in mill capacity and unless there is a compensating saving in freight and smelter charges, it simply is not good business to go beyond a certain point in the way of making clean concentrate Opportunities exist for eliminating one or more steps in the expensive series of processes for recovering various metals, or at least reducing the volume of materials that has to be handled at the most costly steps The beneficiation of nonmetallic minerals likewise affords numerous examples of over-all economies obtainable through more refined methods of mechanical improvement All this leads to the conclusion that perfecting selective processes for isolating pure minerals (e g, galena) virtually free from other sulfides as well as gangue may be productive of industrial economies Conversely, cheapening smelting methods may invade the field of mechanical improvement of ores but, as Kiphng said, that is another story

Jan 1, 1937

By G. C. Trevorrow

STRIP mining during 1943 increased considerably with further extension of mechanical loading in mines already partly mechanized; with the considerable introduction of mechanical loading into hand-loading mines; and with improvements in the use of loading equipment. Extension of the use of machinery both in strip mining and underground is due to reduction in labor supply and increased cost of labor, together with the increased demand for coal during the period of labor shortage.

Jan 1, 1944

By Y. C. Kim, S. L. Barua

Underground coal mine planning has traditionally focused on the mine design aspects concerning safety and efficiency in the quest to produce low cost coal. Very little attention has been given to coal quality control aspects of mine planning at most US underground coal mines. With the enactment of the Clean Air Act of 1970, the generally high sulfur content of coal has become a major concern for the coal-fired power plants in the east. Similarly, the ash and the Btu content of coal are equally important for boiler efficiency. Coal mine planning must incorporate coal quality control aspects as well as traditional safety and efficiency aspects. According to an article in Coal Age (March, 1982), nearly one-half of the US coal exported to Europe does not meet the contract specifications regarding ash, sulfur and Btu contents. Although one of the reasons cited for this problem was "inadequate sampling at the US ports," the more fundamental cause probably lies in the inadequate quality control of run-of-mine (ROM) coal at the source. To perform adequate quality control of ROM coal, mines need predicted short-term in-situ coal quality information. Such predictions are generally based on whatever available sampling information is around the mine workings. Unfortunately, the closest sampling information, in the form of diamond drill hole assays, is often several thousand feet away in most underground coal mines and is inadequate for short-term coal quality prediction purposes. This is because the diamond drill holes (DDH) were traditionally placed in the coal deposit during the mine development phase to determine coal seam continuity and overlying roof conditions. They were not placed for short- term mine planning. A study was undertaken by the University of Arizona for the Homer City Owners in Pennsylvania to show that there is a need for more closely spaced samples, if the short-term coal qualities are to be predicted with any "reasonable" degree of accuracy. Prior to this study, a short-term quality prediction model, STPM, had to be developed. This model uses not only DDH, but also other sample information obtainable during face development work to predict the qualities of in-situ coal that are available in the immediate future.

Jan 1, 1985

By Charles V. Riley

While the late 1960's are known as the years of the public recognition of impending environmental crises, the 1970's will be known as the decade of public concern for improving the quality of that environment. One of the major environmental concerns is the temporary disturbance resulting from coal surface or open cast mining. Increasing energy demands in the U.S., a doubling of electrical power consumption each decade during the present century and the projected needs for the remainder of the century are indications that coal surface mining as a major extractive industry will continue. Coal and lignite, prime energy resources and extremely abundant in these United States, in the face of seemingly limited gas, oil and uranium reserves, are both destined for expanded future use. Presently some extremely serious technological and environmental problems are associated with the development and use of nuclear power. It is true that the extraction and use of coal as an energy fuel poses disruptive problems for the environment, but the solutions to many of the problems are known or can he solved within a reasonable time framework Certainly our national well-being and continued survival as a free nation within the world community automatically dictate the continued use of the coal resource for energy. Concurrently, those engaged in coal surface mining, with the temporary disturbance of the land and water resources, must also realistically conclude that public concern for maintaining and improving the quality of the environment will not diminish. Although as ecological, economic, social and aesthetic elements of cost-benefits and human desires are more adequately understood, a more rational and reasonable public and governmental attitude hopefully will result.

Jan 3, 1973

By T. W. Guy

DURING the past three years the Surface Preparation Committee of the American Mining Congress Coal Operators' Committees has been collecting data on dewatering and drying washed coal, and on screening coal in representative plants in the Eastern and Central bituminous fields. Because of wide variations in bed moisture, such data can be compared only after deducting the bed moisture. It was found that practically every company used a different routine for moisture sampling and determinations. Some reported the moistures as total moistures, others as surface moistures, cur-dried moistures, or oven-dried moistures. For most of the reports it was necessary to esti-mate, from a consideration of the bed moisture and other data available in a given case, corrections to be made in order to obtain surface-moisture figures as a common basis for comparison. At any plant, and regardless of bed moisture, the percentage of surface moisture remaining in a product when the dewatering, or a given stage of the dewatering, has been completed, is the real measure of what has been accomplished. The descriptions and data given with Fig. 1 show that surface-moisture figures show relationships that would not be shown by total moistures. Therefore bed moisture should be deducted, or, if more practicable, the surface moisture of the. products should be meas-ured direct. A preparation engineer finds one per cent, or even a part of one per cent, of surface moisture a very important consideration in the results of his efforts to find the most effective and economical methods of reducing and controlling the surface moisture in his products within the required limits. Therefore it is important for him to have accurate measurements of surface moisture with minimum uncertainty as to whether they some-times include less than the surface moisture and at others all of the surface moisture plus an unknown part of the bed moisture.

Jan 1, 1938

Unitization—in some form from simple agreements among operators to complete consolidation of ownerships—is a means of obviating the wastes of unrestrained competition among owners in extracting oil and gas from a common reservoir, as well as of adjusting its output to the current needs of its owners. It offers opportunity for application of improved production methods which are expected to increase recovery, decrease developing and operating costs, and assist in stabilizing output.

Jan 1, 1930

By G. S. Hume

The total production of crude oil in Canada showed only a small improvement in 1936 over 1935, but developments of great importance took place in Alberta on the west flank of the Turner Valley field in the foothills southwest of Calgary. These have led to renewed activity in drilling such as has not been experienced for many years, and undoubtedly this will result in a very considerable increase in the oil production during 1937.

Jan 1, 1937

Unitization—in some form from simple agreements among operators to complete consolidation of ownerships—is a means of obviating the wastes of unrestrained competition among owners in extracting oil and gas from a common reservoir, as well as of adjusting its output to the current needs of its owners. It offers opportunity for application of improved production methods which are expected to increase recovery, decrease developing and operating costs, and assist in stabilizing output.

Jan 1, 1930

By W. Julian Parton

General Crushed Stone Co. operates a dozen quarries in such rock types as gabbro, basalt, granite and limestone. Drilling characteristics and problems vary from one operation to another so that a variety of equipment and methods must be employed. In addition, it has been found that equipment improvements make it advisable to continuously look for and experiment with new machines and accessories. This article discusses drilling progress at some of the Company's more interesting operations.

Jan 1, 1963

By L. L. McDaniel

DURING the past few years a number of improvements in smelting and power equipment have been made at the Douglas smelter of the FIG. 1.-GENERAL PLAN OF SMELTER. Phelps Dodge Corporation at Douglas, Ariz. In the summer of 1935 work was started on the first unit of a new reverberatory waste-heat boiler plant which ultimately was to furnish steam for a modern high-pressure power plant. A second reverberatory waste-heat boiler unit

Jan 1, 1939

Escalating energy costs and tough environmental standards were two major factors affecting the minerals processing area in 1978 For the most part, new startups and research and development initiatives were directed toward improving process dynamics, investigating alternative processing strategy, and lowering unit costs. In the flotation area, the trend to larger machines continued. Scientific investigation of the modeling and process control of flotation was apparent, as was the research and development of new flotation reagents.

Jan 5, 1979

NOW continuing with the preparation of the moulds I say that it is necessary to give the greatest attention to the differences of the clays as well as to the differences of those things that you wish to mould; and to know that every concavity in the mould produces a convexity and every convexity a hollow following the shape of the original pattern that you have. The pattern should be a body of a harder mated than the thing [78] you wish to mould with and of a substance that is not swollen or disintegrated by moisture. Its archetype may be of marble, bronze, lead, or any other metal, or also of wood, wax, tallow, gypsum, sulphur, or other plaster compositions-in short, of whatever you may have or whatever succeeds best for you, depending on whether the works are large or small and easy or &cult to mould. If you wish to cast them in bronze, you must mould them with loam, covering them with it and then drying it. There are some things in which it is enough to form only one part, such as half- or bas-reliefs. These are easy if they have no undercuts. Some other patterns that are easily handled are formed in two halves, or in three or four pieces, if they are of a hard material. There are also moulds for large statues, which, if one desires to make them of bronze, are first made of wax according to the ordinary procedure. I have in mind to describe every one of these processes in their own place. There are like- wise some moulds that are difficult to make, like scenes on a plane to which figures in full relief are attached, or twisted ornaments or other detached things that cannot be withdrawn from the mould without break-

Jan 1, 1942

By R. S. Hooper

In attempting to describe recent mining developments at the Bunker Hill mine, it may be well to recall first the old days of hand mining when holes were laboriously drilled by hand to a maximum depth of three feet, and were shot one or two at a time, in order that the miner could take advantage of every slip, crack or bedding plane, and so save as much drilling as possible. Broken muck, of course, was loaded by hand shoveling into wheelbarrows or small cars, and heading advances or stope tonnages were governed by the number of men that could find room to work in any given place. The first big improvement over these old methods was the introduction of the reciprocating type of air-powered rock drill. This innovation, crude as it was, enabled the miners to set up a machine and drill a complete round of holes in one shift; but broken muck was still loaded by hand, and the size and rate of advance in headings were limited by time required to remove the broken rock. The next improvement of consequence was the appearance of the hammer-type rock drill, which greatly increased drilling speed over the reciprocating type, and made possible the completion of a full cycle in one shift, by the use of crossbars in headings, and permitted drilling and mucking to be carried on at the same time. Rock drills continued to improve as time passed, and finally the smaller and more efficient mucking machines appeared on the scene, and it became possible to muck out a round of broken rock and have a clean setup for one or more drill columns and machines. A complete cycle of mucking, drilling, and blasting was completed in one shift with an average advance of five feet. These conditions prevailed for several years, but as the mine grew deeper, the distances to transport the workers grew longer, and this fact together with the shortening of the working day, soon presented the problem of attempting to complete a cycle of operations in a shift of only six hours at the working faces. Anticipating this condition, the operating heads at the Bunker Hill had started an intensive study of more and better mechanization, and over a period of comparatively few years have adopted and placed in service methods and machines that make it possible for a three-man crew to consistently advance headings seven by nine feet in cross section, at the rate of eight feet, and more, per shift, doing all the mucking, switching, drilling and loading. These improvements consist of the following major items: I. The development of a light, flexible, easily transported jumbo equipped with pneumatic columns (Fig I), that has decreased the "setting up" and "tearing down" time an average of 11/2 hr per shift, Or 25 PCt of the available working time. These jumbos were developed at the Bunker Hill mine by members of the staff and consist of two pneumatic columns attached to a suitable carriage. They fold

Jan 1, 1949

By R. S. Hooper

IN attempting to describe recent mining developments at the Bunker Hill mine, it may be well to recall first the old days of hand mining when holes were laboriously drilled by hand to a maximum depth of three feet, and were shot one or two at a time, in order that the miner could take advantage of every slip, crack or bedding plane, and so save as much drilling as possible. Broken muck, of course, was loaded by hand shoveling into wheelbarrows or small cars, and heading advances or stope ton¬nages were governed by the number of men that could find room to work in any given place. The first big improvement over these old methods was the introduction of the reciprocating type of air-powered rock drill. This innovation, crude as it was, enabled the miners to set up a machine and drill a complete round of holes in one shift; but broken muck was still loaded by hand, and the size and rate of advance in headings were limited by time required to remove the broken rock. The next improvement of consequence was the appearance of the hammer-type rock drill, which greatly increased drilling speed over the reciprocating type, and made possible the completion of a full cycle in one shift, by the use of crossbars in headings, and permitted drilling and mucking to be carried on at the same time. Rock drills continued to improve as time passed, and finally the smaller and more efficient mucking machines appeared on the scene, and it became possible to muck out a round of broken rock and have a clean setup for one or more drill columns and machines. A complete cycle of mucking, drilling, and blasting was completed in one shift with an average advance of five feet. These conditions prevailed for several years, but as the mine grew deeper, the distances to transport the workers grew longer, and this fact together with the shortening of the working day, soon presented the problem of attempting to complete a cycle of operations in a shift of only six hours at the working faces. Anticipating this condition, the operating heads at the Bunker Hill had started an intensive study of more and better mechanization, and over a period of comparatively few years have adopted and placed in service methods and machines that make it possible for a three-man crew to consistently advance headings seven by nine feet in cross section, at the rate of eight feet, and more, per shift, doing all the mucking, switching, drilling and loading. These improvements consist of the following major items: I. The development of a light, flexible, easily transported jumbo equipped with pneumatic columns (Fig I), that has decreased the "setting up" and "tearing down" time an average of 1 1/2 hr per shift, or 25 pct of the available working time. These jumbos were developed at the Bunker Hill mine by members of the staff and consist of two pneumatic columns attached to a suitable carriage. They fold

Jan 1, 1947

By Thunaes, Arvid

Pilot plant test work in 1942 and 1943 showed that by a combination of desliming, fine-size classification, and Sullivan deck concentration it is possible to recover heavy minerals such as cassiterite at least as fine as 10 microns in size. This appreciable improvement in gravity concentration practice has been substantiated by several full-sized plants.

Jan 1, 1950