Search Documents

By M. A. Grossman

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of unhardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of o.-2o per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as would appear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.2o per cent Mo provides a factor of 1.63, an increase of over 6o per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater harden ability will be obtained by using, for example, o.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By John W. Wagner, Robert K. Willardson

Single crystals of Pbl-xSnxTe have been grown from nonstoichiometric, cation-rich melts with the objective of producing as-grown, bulk material containing carrier concentrations ranging from 1016 per cu cm to 1018 per cu cm. Three specific crystal composi-tions were investigated in detail; x = 0.00, 0.10, and 0.17. Pull rates of from I to 3 mm per hr were used. Single crystals were successfully pulled from melts containing as little as 30 at. pct Te. Hall coefficients, resistivities, and carrier mobilities of these materials were determined. The relationship between the composition of the melt and the carrier concentration in the as-grown crystal has been studied for the three crystal compositions of interest. BULK single crystals of Pb,-,Sn,Te have previously been grown from stoichiometric melts.1,2 Such crystals are p-type and have relatively high carrier concentrations ranging from -9 x 1018 per cu cm for PbTe to -8 x l020 per cu cm for SnTe at 77°K. These carrier concentrations result from deviations from stoichiometry (lead vacancies) in the as-grown crystals. Since lower carrier concentrations are desirable for electrooptic device applications, these crystals are usually subjected to long-term, isothermal anneals.' This paper reports on the growth of Pbl-xSnxTe single crystals from nonstoichiometric melts with the primary objective of producing as-grown material containing relatively low (1016 to 1018 per cu cm) carrier concentrations and also reports on the general characteristics of these crystals. The phase relationships in the Pbl-xSnxTe systems are such that materials solidifying from nonstoichiometric, cation-rich melts will have smaller deviations from stoichiometry than materials grown from stoichiometric melts. Fig. 1 is the T-x phase diagram for PbTe in the vicinity of the stoichiometric composition.3 A crystal grown from a stoichiometric melt will solidify at a melting point maximum at which the solid will contain -0.5002 atom fraction of tellurium. PbTe single crystals grown in our laboratories from stoichiometric melts have carrier concentrations of 9 x 10" per cu cm, indicating that the excess tellurium in the crystals is as expected from this phase diagram. However, growth of PbTe from a lead-rich melt will result in material having a more nearly stoichiometric composition. Although the addition of Sn to the melt shifts the solidus curve further toward the tellurium-rich side,4 the general discussion given for PbTe applies to the Pbl-xSnxTe systems as well. EXPERIMENTAL Single crystals of Pb1-xSnxTe have been grown in our laboratories from nonstoichiometric, cation-rich melts using the Czochralski technique and boric oxide liquid encapsulation. The details of the growth apparatus and growth technique have been reported in a previous paper on growth of these alloys from stoichiometric melts.2 In the present study, three specific crystal compositions were investigated in detail; x = 0.00, 0.10, and 0.17. Growth of alloy crystals from nonstoichiometric melts requires considerable care, and good quality single crystals were obtained in this study only by optimizing the mechanical and thermal stability of the growth system and by using pull rates of from 1 to 3 mm per hr (Pbl-xSnxTe crystals are easily pulled from stoichiometric melts at rates of from 5 to 10 mm per hr). The liquid encapsulation technique was found to yield near-ideal conditions, since the B2O3 layer increased the thermal stability at the growth interface, permitted easy attainment of near-ideal thermal gradients, and dampened vibrations at the melt surface. The hygroscopic character of the B2O3 was a slight problem and vacuum heat treating was necessary to completely remove the water from the boric oxide. During initial growth, the seed diameter was reduced and a narrow neck (1 to 2 mm diam) of several millimeters length was grown. The latter steps were found to be necessary for the growth of single crystals, i.e., if either of these two requirements were

Jan 1, 1970

By A. M. Turkalo

IT is a well-known fact that martensitic steels show a greater resistance to brittle fracture than do pearlitic and bainitic steels. It was, therefore, thought worthwhile to investigate the mode of brittle fracture with respect to structure by studying the effect of various austenite decomposition products on the propagation of brittle fracture in steel by means of electron microscopy. Newly developed replication techniques together with the advantages of the electron microscope such as great depth of field, available high magnification and easy adaptation to stereophotography make electron microscopy very suitable for fracture studies. EXPERIMENTAL PROCEDURE An essentially plain carbon steel containing 0.56 pct C, 1.30 pct Mn, 0.02 pct P, 0.03 pct S and 0.22 pct Si was used in this investigation. The following table gives the heat treatments used to obtain the various austenite decomposition products: The resulting austenite grain size from the 870°C austenitization treatment was about an ASTM No. 7 grain size. The specimens which were 2 in. long, 1/4-in. diam bars were austenitized in a tube furnace through which argon gas was blown. The tube was not, however, air-free and the specimens were not completely oxide-free. Isothermal treatments were done in a lead bath. With the exception of the fully hardened specimen and the one as-isothermally transformed at 300°C the heat treated specimens were notched in the following fashion with a jeweler's saw. A cut about 0.08 in. deep was made perpendicular to the length of the bar. The specimen then was rotated about 45 deg and another cut about 0.08 in. deep was made. In the case of the hard martensitic and bainitic specimens, only one cut was made and the depth was not controlled. The design of the two-cut notch caused fracture to initiate at the point of intersection of the two saw cuts. The specimens were broken at -196°C in a Charpy impact testing machine. In order to hold the specimens securely in the impact machine two square pieces of mild steel were made about 5/8 in. long having the same cross section as that of a standard Charpy specimen but containing a hole 1/4 in. diam through the center of the cross-section. These adapters were slipped over the ends of the test specimen which was then secured tightly by means of set screws in the adapters. The specimen with the adapters was cooled to -196°C in liquid N,, then placed in the impact machine and broken within 3 sec. One half of the broken specimen was used for the electron microscope study of the actual fracture surface. The other half was nickel-plated and a cross section through the notch and fracture was polished for electron microscope examination. Carbon replicas of the fracture specimens for the electron microscope study were made essentially according to Bradley's evaporation technique.' Both direct carbon and two-stage carbon replication techniques were used. In the case of the direct carbon technique, a thin layer of carbon was evaporated first at an angle of about 45 deg to the mean fracture surface and then another film of carbon was evaporated normally to the fracture surface. The carbon replica was freed electrolytically.2 The specimen was made an anode in a 10 pct Nital polishing solution. It was etched intermittently by shutting off the power now and then. The freed replica was washed in 40 to 50 pct water solution of nitric acid for 10 min or so, then washed in water and picked up on a screen for examination. The two-stage carbon replication technique involved first making a primary replica of cellulose * acetate from which a carbon replica was then made. One side of a strip of cellulose acetate wet with acetone was pressed lightly against the surface of the specimen, allowed to dry and then stripped. Prior to the deposition of carbon, which was done at 90 deg to the cellulose acetate replica surface, chromium was evaporated at 45 deg. After the carbon evaporation the cellulose acetate was dissolved in acetone according to the Jaffe method3 leaving the carbon replica preshadowed with chromium for examination.

Jan 1, 1961

By A. K. Mukherjee, John E. Dorn

The effects of strain rate and temperature on the critical resolved shear stress for (321)[111] slip were determined for the silver-rich CsCl type of intermetallic compound AgMg. The flow stress increased only slightly as the test temperature was first decreased below room temperature; a rapid increase in the flow stress was obtained with yet further decrease in temperature from about 250' to 4OK. The effect of both the temperature and strain rate on the flow stress over the low-temperature range could be rationalized satisfactorily in terms of the Peiwls mechanism when the deformation was controlled by rate of nucleation of pairs of kinks. IN spite of the well-documented interest of metallurgists and engineers concerning the mechanical behavior of intermediate phases and intermetallic compounds, very little definitive information is available on this important subject. As recently summarized by westbrook,1 only limited and modest progress has been made thus far in elucidating the details of the mechanism of plastic deformation for the intermetallic compounds; the available information largely concerns phenom-enological descriptions of empirical observations and experimental facts, principally with reference to poly crystalline aggregates. The present report on the elucidation of the rate-controlling mechanism for slip in the bcc structure of AgMg is part of the comprehensive program of a systematic investigation on the mechanical behavior of intermetallic compounds. The intermetallic compound AgMg has a CsCl type of lattice structureZ and is completely ordered up to its melting point of 820c3 This material was selected for our present investigation because of its simple crystal structure, moderate and congruent melting point, ordered structure persisting up to the melting point, and some solubilities of the constituent elements, which could be expected to help in the growing of single-crystal specimens. Whereas previous investigations on the properties of AgMg include hardness,*"6 slip systems,7 tensile flow stress of polycrystalline specimens,' and electrical resistivity,4 the current investigation will be directed principally at elucidating the rate-controlling dislocation mechanism responsible for slip in single crystals at low temperatures. It will be shown that the strain rate is consistent with a model involving the rate of nucleation of pairs of kinks by the Peierls mechanism for plastic deformation. EXPERIMENTAL TECHNIQUES Single-crystal specimens of the AgMg intermetallic compound were prepared and tested as follows: 1) A master alloy ingot of AgMg was produced by melting and chill casting the high-purity silver (99.995 wt pct) and high-purity magnesium (99.997 wt pct) in an induction furnace under a helium atmosphere. 2) Sections of the above-mentioned ingot were placed in a graphite mold containing a spherical cavity in which a single-crystal sphere of 1 in. diam was grown under helium by the Bridgman technique. 3) The operative slip systems were investigated at room temperature on a singlecrystal of AgMg, from measurements of the angles made by the slip traces on the two surfaces of the specimen, which were at 90 deg to each other. The investigation confirmed that the AgMg compound undergoes slip primarily in the (321) plane and in the [Ill] direction, but a small amount of secondary slip was also noticed in the (112) (111) system. No slip was observed in the (110) planes. 4) The single-crystal sphere, mentioned earlier, was oriented in a graphite mold containing a cylindrical cavity of 3/8 in. diam above the spherical receptable to give the angle xo = 45 deg between the axis of the cylindrical bar and the normal to the slip plane (321), and the angle AO = 45 deg between the slip direction [Ill] and the axis of the bar. Oriented single-crystal bar seeds were produced by melting, under a helium atmosphere, a polycrystalline bar in the cylindrical cavity above the oriented spherical seed and by growing an oriented single-crystal bar from the seed. 5) Finally, oriented single-crystal specimens were grown from these cylindrical seeds. 6) The cylindrical specimens were machined in a High-Tension Spark Cutting unit to give a 2-in. gage length. The spark-machined gage section was elec-tropolished in a bath containing 200 ml of H3PO4,

Jan 1, 1964

By R. Q. Shotts

Nitric acid oxidation rate analyses of three coals, previously studied microscopically by the Bureau of Mines, revealed three components. Relative quantities agree with those found for the four components given by the Bureau and results are consistent with current ideas of coal constitution. Possible multi-component composition for bright coal and a reactivity-rank relation are suggested. THE physically dissimilar components of bituminous coals often are easily recognized mega-scopically. Under the microscope, reflected light or light transmitted through thin sections reveals the presence of the different components, even when these are intimately mixed. Optical methods for the quantitative estimation of the relative abundance of the various components, both by means of thin sections and by particle count, have been fully described.'. ' It has long been recognized that there are chemical and physical differences between the various petro-graphic components of bituminous coals, although analytical differences usually are small.:'. ' Only in the case of fusain have chemical differences been used for quantitative determination of a component. C. C. Hsiao and associates, at the Mineral Industries Experiment Station of the Pennsylvania State College, have described a method of analysis which is based upon the differences in the rate of nitric acid (8N) oxidation, fusain, and the other components of coal."," The reproducibility of their method and its applicability in checking microscopic determinations of fusain content have been supported by several independent investigations.'. " The writer has proposed the use of differences in oxidizability for the estimation of other components." "' The results of the oxidation of whole coals and of float-and-sink fractions of coals were reported. In most cases the plots of the logarithms of the percent dry, non-fusain, organic residue from oxidation, against time, revealed the presence of at least two distinct components. Both components appeared to oxidize according to a first order law, but the reaction constants for the components were distinctly different. One or more of the dull density fractions were found to contain but one component, and some of the lower rank coals oxidized in such a way as to suggest the presence of three components. A suitable way to check the identity and significance of the components delineated by oxidation would be to analyze a sample of coal both by the nitric acid oxidation procedure and by a microscopic method. The writer was wholly unfamiliar with either of the microscopic techniques commonly used, and to make such a comparison it was necessary to rely upon microscopic analyses made by someone else. It is hoped that some laboratory which is equipped to make both types of analyses will some day make them upon identical samples. During the past 20 years, four Alabama coals have been analyzed petrographically and the results published by the United States Bureau of Mines. They are: 1—Flat Top mine, Mary Lee bed; 2—Empire mine, Black Creek bed; 3—Wylam No. 8 mine, Pratt bed, all in the Warrior field; and 4—Soot Creek mine, Fairview bed, in the Coosa field."-" Of these, only the Flat Top mine is still operating. Because of the closing of these mines, it first appeared necessary to rely upon the indirect and unsatisfactory procedure of sampling the beds in other mines located as near to the closed mines as possible. Upon investigation, however, it was found that the Bureau of Mines still had, in storage, the very same samples which had been used in the published petrographic studies. The Bureau very generously furnished about 2000 g each of the Pratt, Mary Lee, and Fairview bed coals, largely lumps but with some fines. The blocks of coal, when received, still were covered by the paraffin coating which had been placed on the polished surface, in the case of the Mary Lee coal almost twenty years ago. Procedure The procedure for oxidizing the coal sample and removing the alkali-soluble humic acid has been described. In the present study, oxidation periods of 1/6, 1/3, 1/2, 3/4, 1, 2, 3, and 4 hr were used. All oxidations were made in triplicate. After the paraffin had been removed in boiling water and the coal washed carefully with cold benzene, the entire sample of approximately 2000 g, obtained from the Bureau of Mines, was crushed to pass a No. 4 sieve. About 200 g of this material was pulverized to pass

Jan 1, 1954

By K. M. Rolls, J. Wulff, D. A. Colling

Solid-solution alloys of the Ta- Ti system containing up to 70 at. pct Ti were melted and fabricated into wire. Steady magnetic-field measurements of cold-worked wires at 4.2°K indicate that the resistive critical field increases smoothly with increasing titanium, reaching a maximum of 93 kG (J = 1 amp per sq cm) for a composition of about 50 at. pct Ti. The composition dependence of the resistive critical field indicates it is largely paramagnetically limited for alloys containing more than 35 at. pct Ti. For cold-worked wires the value of the critical current density, Jc , was found to be insensitive to composition changes for compositions in excess of 20 at. pct Ti. It was observed that Jc could be increased by final-size heat treatment at 400°C without altering the value of- the resistive critical field. Experimental data are used to calculate the electronic specific-heat coefficient and the "upper critical field" for the alloys studied. THE effect and importance of metallurgical structure on superconducting properties have been summarized by Livingston and Schadler.1 Specific work on solid-solution alloys such as Nb-zr2-7 and Nb-Ti5-7 have shown that critical current density (Jc) and superconducting transition temperature are structure-sensitive. Berlincourt et al.6,8,9 in their studies of transition-metal alloys find that Ta-Ti alloys remain superconducting at fields comparable to Nb-Ti alloys. 6,8 Transverse critical current tests of a Ta-10 at. pct Ti alloy10 and longitudinal critical current tests of a Ta-25 at. pct Ti alloy1' indicate that such alloys are capable of carrying high currents at intermediate fields (-40 kG). The work reported in the present paper was undertaken to explore the superconducting properties of further compositions in the Ta-Ti alloy system as well as the structure sensitivity of the superconducting properties. I) EXPERIMENTAL PROCEDURE Alloys were prepared by melting tantalum (Fansteel Metallurgical Corp., 99.96 pct purity) and iodide, crystal bar titanium (Foote Mineral Co., 99.92 pct purity) mixtures in an arc furnace on a water-cooled copper hearth using a tungsten electrode. Melting was accomplished in a purified, gettered argon atmosphere at pressures from 250 to 400 Torr. Each alloy was turned and remelted fourteen times to assure complete mixing of tantalum and titanium. Ex- cessive coring in the cast samples was, nevertheless, observed. This was somewhat reduced by annealing in vacuo at 1000°C for 13 hr. The ingots were then machined to 0.250 in. diam, jacketed in Type 304 stainless-steel tubing, and swaged to 0.140 in. diam. They were then drawn to 0.010-in.-diam wire. Alloys containing up to 70 at. pct Ti were readily cold-drawn to wire in this manner. Later experiments showed that oxygen additions up to -3000 ppm could also be cold-worked into wire. Test samples for superconductivity measurements in the 2-in, air-core Bitter solenoids of the M.I.T. National Magnet Laboratory were prepared from 10-in. lengths of 0.010-in.-diam wire, cleaned of residual wire-drawing lubricant. Current contacts were made by clamping clean copper tubing over both No. 18 current lead wire and the ultrasonically indium-tinned ends of the specimen wire.12 Potential leads of No. 32 copper wire were connected to the specimen by ultrasonic soldering in an indium bath. The potential lead separation was about 4 cm, corresponding to the circumference of the Bakelite rod to which the wire was affixed with half-mil Teflon tape. The final specimen configuration is shown in Fig. 1. Specimens were lowered into a liquid helium bath (4.2oK) in a double solenoid dewar and positioned so that the maximum magnetic field was oriented transverse to the wire axis of the gage section. Measurements were made by passing a current through the specimen at a preset solenoidal magnetic field. The current was increased until a 1-pv potential difference appeared across the gage section (1/4 µv per cm). At low magnetic fields, however, it was not possible to use this criterion because power-dissipation difficul-

Jan 1, 1967

By R. M. N. Pelloux

This study of aluminum-copper alloys had two aims: 1) To determine the effect of the amount and distribution of a second phase, CuAl2, on the creep-rupture strength, ductility, and fracture characteristics of the alloys. The work of Gemmell and grant' on single-phase aluminum-copper alloys provided a basis for the present study. 2) To attempt to provide a relation between the microstructure and strength of two-phase alloys deformed at comparatively high temperatures (greater than 0.45 T,). The creep behavior of the two-phase magnesium alloys Mg;Ce and Mg-A1, has been treated by Roberts. 9 In work reported by Sully and Hardy4 and by Underwood, Marsh, and Manning~ on A1-Cu two-phase alloys, and also in a portion of the work of Gemmell and grant,' aging took place during the creep tests. 'In the present work, overaged aluminum-copper alloys were subjected to creep deformation at two temperatures, 500 and 700OF. The overaging treatments to produce the precipitate dispersions were performed prior to the test, at temperatures which were the same as the ultimate respective test temperatures. Hence, the present study is concerned with the creep behavior of stable (in contrast to "underaged") two-phase A1-Cu alloys, i.e., alloys in which no depletion of the solid-solution matrix occurred during: creep. MATERIALS AND PROCEDURE A 2 and a 3 pct Cu alloy, supplied by Alcoa, were studied; Table I shows the compositions. The grain size of the specimens, 0.9 to 1.0 mm, was achieved by annealing the machined test bars for 2 hr at 1000°F, followed by furnace-cooling to 900°F, and homogenizing for 4 hr. Both compositions are in the single-phase condition at 900°F. Two types of overaged dispersions, termed "over-aged I" and "overaged 11" were prepared after the grain size and the homogenization anneals. The overaged I alloys were prepared by quenching to room temperature after homogenization, aging at either 500' or 700°F for 72 hr, and air-cooling to room temperature. The overaged I1 alloys were prepared by furnace-cooling after homogenization, to either 500' or 700°F, and holding at the necessary temperature for 72 hr. The times for furnace-cooling from 900°F to 700° and 500°F were, respectively, about 2 and 3.5 hr. The structures of the A1-2 pct Cu alloys are shown in Fig. 1 (overaged I) and in Fig. 2 (overaged 11). A comparison of Figs. 1 and 2 shows that in the overaged I alloys the precipitate particles along the grain boundaries are much more closely spaced and the grain boundaries are straighter than they are in the overaged I1 alloys. Further, the particle size and spacing in the grains are smaller than in the overaged I1 alloys. Microstructures of the A1-3 pct Cu alloys have not been shown; the structures of these alloys differed from those of the A1-2 pct Cu alloys only in that the distribution density of the particles was greater. The creep specimens had a gage section 1 in. long with a diameter of 0.155 to 0.195 in. Before testing, specimens were electropolished in a solution of 100 cc glacial acetic acid, and 30 cc of 60 pct perchloric acid, at 40' to 50°F, at 24 v. The specimens were kept refrigerated prior to testing to avoid precipitation at room temperature. Constant stress creep tests were conducted; the load was applied 75 min after heating of the specimens to test temperature had begun. EXPERIMENTAL RESULTS Creep-Rupture—Fig. 3 shows the log stress-log rupture life plotfor the overaged alloys studied, and also for the underaged A1-2 pct Cu alloy.' At 700°F, the stress-rupture life relationship is nearly independent of both the amount of precipitate (i.e., composition) and of the type of overaging treatment (i.e., precipitate dispersion). At 500°F it is apparent that the increase in rupture life that was ex-

Jan 1, 1960

By Donald B. Evans, Robert D. Pehlke

The solubility of nitrogen in liquid Fe-B alloys has been measured up to the solubility limit for the formation of boron nitride. The activity coefficient of nitrogen increases with increasing boron content in the range 0 to 7 wt pct B. From experimen -tal data, values have been calculated for the B-N interaction parameter e3 at temperatures in the range 1550" to 1750°C. A value of 0.038 has been estimated for the boron self-interaction parameter eg at 1550°C. The standard free energy of decomposition of boron nitride into the elements dissolved in liquid iron has been determined to be: ?F° = 45,900 -21.25T in the range from 1550° to 1750°C. The nitride is assumed to be of composition BN. BORON nitride has an unusual combination of properties which make it appear attractive in a wide range of engineering applications. Some of its more important and most recent applications are in the nuclear area, particularly in connection with the liquid-metal cooled reactor concept now receiving considerable emphasis. Boron nitride has a high degree of stability at elevated temperatures. It also has excellent ma-chinability and the ease with which its crystals deform suggests applications as a lubricant. These properties stem from a hexagonal layer-type structure similar to the structure of graphite. One of its primary uses to date has been for seals in liquid-metal pumping systems. It is also used in nuclear reactors as an insulating layer to separate two solid metals which are not themselves compatible under the conditions of temperature and atmosphere in which they are used. Its inertness to liquid metals has also suggested use as a mold-release agent in casting processes. In addition to its excellent machinability and reported inertness to liquid metals such as iron, silicon, aluminum, copper, and zinc, boron nitride has high thermal conductivity and excellent thermal shock resistance. This combination of properties would make it appear ideal as a refractory crucible material for refining of high-purity liquid metals, for example high-quality steels. However, since it is known that concentrations of boron as low as 50 ppm can have a marked effect on the physical properties of certain steels,' in particular on the creep and stress-rupture properties, an investigation was undertaken to define accurately the chemical equilibrium among boron, nitrogen, and liquid iron in the range of steelmaking temperatures. EXPERIMENTAL PROCEDURE Two experimental approaches to this problem were employed: a Sieverts' method and a quenching method. In the first method, the Sieverts' technique was used to measure the equilibrium nitrogen solubility in liquid Fe-B alloys of 0 to 7 pct B as a function of nitrogen gas pressure over the melt. The solubility limit of the boron nitride phase formed was determined by the point of departure of the nitrogen absorption from Sieverts' Law. This technique has been applied to liquid Fe-Ti alloys by Rao and parlee,' to liquid Fe-A1 alloys by Evans and Pehlke,3 and to solid Fe-V alloys by Fountain and Chipman.4 In the second method a melt of liquid iron was held in a crucible of boron nitride under a known partial pressure of nitrogen gas. After thermodynamic equilibrium was attained, the melt was quenched in a stream of helium and then analyzed by wet-chemical methods for boron and nitrogen. The Sieverts' apparatus used in the first method was essentially of the same design as the one described by Pehlke and Elliott.5 The charge materials were vacuum-melted high-purity iron (Ferro-vac E) supplied by the Crucible Steel Co. and -325 mesh boron powder supplied by Cooper Metallurgical Associates of Cleveland, Ohio. The boron contained less than 0.02 wt pct O, according to supplier's analysis. Recrystallized alumina crucibles were used to contain the melt. Examination of solidified melts showed these crucibles to be satisfactory with no evidence of any reaction or physical penetration of the crucible wall by the melt. The melt temperature was measured by a disappearing filament-type optical pyrometer sighted vertically downward on the melt surface through a 1/4-in.-diam sight hole in the crucible lid. The pyrometer was calibrated against the melting point of pure iron in the same apparatus, taking the emissivity of

Jan 1, 1964

By R. L. McCarron, G. R. Belton

The diffusivities of oxygen and sulfur in liquid iron have heen determined hy a capillary technique in which the surface concentrations of the solutes were established by means of appropriate H2/H2 and H2S/H, gas mixtures. Total diffusate and concentration profile results are shown to be in good accord, yielding for- 1560 and Supporting results at 1660°C are also presented. The conditions necessary to avoid gas transport control in this type of experiment are discussed. IN spite of their importance in understanding the kinetics and mechanisms of refining reactions, the dif-fusivities of oxygen and sulfur in liquid iron are not well established. Accordingly, as a first step in studies of rates of solute absorption from the gas phase into liquid iron, new measurements of these diffusivities have been made and are presented in this paper. The only published results for the diffusion of sulfur in pure liquid iron are those of Kawai.' He used a diffusion couple technique in which two cylindrical specimens, one containing sulfur and the other with negligible sulfur concentration, were joined together and held in a refractory capillary. After an experiment, the sample was quenched and the concentration distribution of the solute determined. Kawai recognized that significant changes in solute distribution occurred during melting and freezing and he attempted to correct the concentration profiles for these effects to give a sulfur diffusivity of 4.6 x 10-6 sq cm per sec at 1560°C. The method of correction, however, was not rigorous and the uncertainty in this result cannot be easily assessed. Koslov et a1.2 have reported the diffusivity of oxygen in iron as 7.8 x 10"3 sq cm per sec at 1660°C. This value appears to be unreasonably high but, unfortunately, details of their experiments are not available. Shurygin and Kryuk have used the rotating disc method for a study of oxygen diffusion in liquid iron. In their experiments a silica disc was rotated in liquid iron containing oxygen, and the rate of formation of liquid iron silicate was determined by measuring the decrease in weight of the disc. On the assumption that the rate of dissolution was controlled by the diffusion of oxygen in the iron, the diffusion coefficient was computed to be 5.2 x sq cm per sec at 1550°C. However, the Levich equation, which was used to interpret the rate data, was originally de- rived for the case of mass transfer between a solid disc and a single-phase liquid. The hydrodynamic and diffusion boundary layers in the iron stirred by a disc, via coupling of the silicate melt, may be appreciably different from those predicted by Levich's equations. Recently, Novokhatskiy and Ershov, using an identical experimental method to that of Shurygin and Kryuk, obtained a diffusivity for oxygen in liquid iron of 1.22 x 104 sq cm per sec at 1550°C: no reasons were offered for the disagreement. Schwerdtfeger5 has also recently studied the diffusivity of oxygen in liquid iron. He reacted shallow melts of liquid iron, 0.5 to 1.0 cm deep and contained in high-purity alumina crucibles, with appropriate H20-HZ-He mixtures. The total sample was analyzed, without sectioning, to obtain the average concentration of diffusate. A value at 1610°C of D = 12(3) x 10-5 sq cm per sec was obtained from the results of twenty experiments.= Oxygen profile measurements, which were carried out in three additional experiments using long capillaries and the semiinfinite boundary conditions, indicated a diffusivity about half that computed from the shallow bath experiments. Possible sources of error in Schwerdtfeger's study will be discussed later in this paper. EXPERIMENTAL TECHNIQUE The essential arrangement of the diffusion cell is shown in Fig. 1. The liquid iron was contained in an alumina capillary, 3 to 4 mm diam and 3 to 9 cm long, which was supported by a hollow alumina pedestal and this whole assembly was held within a movable alumina reaction tube. This tube, which was about 7 mm in bore

Jan 1, 1970

By D. H. Yardley

GEOCHEMICAL investigation of trace elements in surface materials was begun near Ely, Minn., in 1953 along the basal contact of Duluth gabbro with Giants Range granite (Fig. 1). This article presents data on the distribution of copper and nickel in till and in stream sediments in the area and proposes an explanation for the types of distribution found. The Duluth gabbro, one of the world's largest basic intrusives, intrudes rocks which range in age from Keewatin to middle Keweenawan. Within the test area the gabbro is in contact with granite except for short sections where it is in contact with remnants of iron formation. Sulfide mineralization occurs within the gabbro, near and parallel to the basal contact for a distance of several miles. Schwartz and Davidson' have described the geologic setting of the mineralization. The sulfides, believed to be syngenetic, include chalcopyrite, cubanite, pentlandite, pyrrhotite, and minor amounts of bornite. They occur disseminated in the silicates and as small interstitial masses. The ratio of copper to nickel is about 3.8:1, based on 66 chemical analyses of rock samples from various outcrops (Ref. 1, p. 702, and Ref. 2). Test Procedures: With specified exceptions, all nickel and copper tests were made by the chromo-graph method,:' which measures the intensity of a colored spot formed by a reaction between the metal being determined and special reagent paper. The intensity is then compared to the intensity of spots prepared from samples of known metal content. Details of the test procedure are outlined in another article (Ref. 4, pp. 77,78). All soil samples tested in this investigation to date have been weighed on an analytical balance. However, a volumetric scoop designed to provide about 0.1 g of soil adds to the speed and ease of testing and has been found to give satisfactory results (Ref. 5, p. 531, and Ref. 19). The size of the samples used for the tests was 0.1 g. Whenever such small samples are used there is some question as to whether they are representative of the several grams in the field sample. Many repeat tests of the samples used in this investigation demonstrated that results can be reproduced within the limits of accuracy of the method without formal mixing beyond that inherent in screening the soil fractions. Furthermore, the 0.1 g is probably as representative of the field sample as the field sample is of its area of influence. Hawkes and Lakin (Ref. 6, p. 291), who considered the general problem, compared ground and quartered bulk samples of 500 g with 5-g grab samples. They concluded that "there is no significant loss in accuracy of data by substituting grab samples for bulk samples." The term soil implies somewhat different things to the geologist, engineer, and soil scientist.' For convenience the term as used in this article refers to unconsolidated material (the mantle) overlying bed rock. Sampling Procedure: Samples were taken at 100-ft intervals along north-south traverse lines across the gabbro-granite contact. The soil (till) samples were taken at an average depth of 1 ft, which was below the high-humus surface layer and into clean till. Samples taken at 1-ft intervals down to ledge showed as high a metal content at 1 ft below the air-surface as at greater depths and in two instances were slightly higher. The till at 1-ft depth did not appear to differ from material at greater depths. Total depth to bedrock has been tested at only a few points and where measured varied from 1 to 10 ft. Aerial Distribution Contours and Profiles: Plotting of copper, nickel, and cobalt content in contour form (Fig. 2) shows that anomalous amounts of these metal ions occur in till over and closely adjacent to mineralized areas of the gabbro. Contouring nickel content alone, or the copper content, outlines the same target area. Contours of the copper content provide a more distinct anomaly than nickel because of the higher copper concentration. The traverses are rather widely spread for interpolation; however, drilling has confirmed the target area essentially as shown.

Jan 1, 1959

By A. Lubinski, J. L. Logan, W. S. Althouse

A4ost gas twells and flowing oil wells are completed and treated through a string of tubing and a packer. Changes in temperature and in pressure inside or outside the tubing will: (I) if free motion of the tubing inside the packer is permitted, increase or decrease the length of the rubing; or (2) if free motion is prevented, induce forces in the tubing and on the packer. If pressure inside the tubing is greater than outside, the tubing may buckle helically even in the presence of a packer-to-tubing tension. The tubing will always buckle, and much more severely, if free motion is permitted. The buckling may be prevented by pulling the tubing in sufficient tension. The prediction of these forces and tubing movement has here to fore been based upon calculations that did not inciude helical buckling. This paper preseitts means with which these length or force changes can be calculated while taking into account the effect of helical buckling. To avoid damaging formations, failure of remedial operations, or damage to the tubing or packer, application is made to practical problems involving calculations of the required length of seals, amount of sluckoff or tension, and prevention of permanent corkscrewing. INTRODUCTION Leakage of a packer may result in costly failures of such operations as squeeze cementing, hydraulic fracturing, etc. To avoid such failures, the authors are often asked questions pertaining to the length of necessary seals, the amount of necessary slackoff, etc. Published work' does not take into account helical buckling of tubing. Investigation of helical buckling was prompted by the fact that allowance must be made for this phenomenon in order to provide relevant answers. In the past, theoretical work on helical buckling was confined to conditions for which such buckling does not The mathematical treatment of behavior in a buckled condition, given in the Appendix, is novel. Assumptions upon which this investigation is based are listed and discussed in a special section. The following are a few of the many kinds of problems which may be solved with this paper. 1. Consider a packer in which tubing may move. Such movement will occur after pressures and temperature are changed. The paper provides means for: (a) calculating the amount of such movement and, therefore. the required length of seals; and (b) calculating the necessary amount of initial slackoff, for which there is no danger of unsealing the packer, if the length of seals is given. Such calculations, as well as those which follow, tully take into account the fact that part of the movement ib due to elastic helical buckling of the lower part of the string. This buckling may occur even in tubing under tension. Insufficient initial slackoff for a given length of seals, or insufficient length of seals for a given slackoff, may result in costly failures. A field case of such a failure will be given further in this paper. 2. In the case in which tubing cannot move in the packer, changes of pressure and temperature result in tubing-to-packer forces and forces in the tubing above the packer, both of which may be calculated. This knowledge is important because, if these forces are too large, the) could damage the packer or the tubing. 3. For wells in which wireline tools are to be run through the tubing, the paper provides means to keep the tubing from buckling, thereby permitting free passage of tools. 4. In deep wells, mainly in the presence of large casing, tubing may become "corkscrewed", i.e., take a permanent helical set. A field case is described further in the text. Using this paper, one may calculate in advance conditions under which permanent corkscrewing would occur, and then take preventive steps. HELICAL BUCKLING Consider a string of tubing, freely suspended in the absence of any fluid inside casing, as shown in Fig. I(a). Now consider an upward force F applied at the lower end of this tubing. This force compresses the string; and if the compression is large enough (which is always the case in actual problems), the lower portion of the string will buckle into a helix, as shown in Fig. 1 (b). The lower end of the tubing is subjected to a compression F. This compression decreases with the distance from the bottom and becomes nil (neither compression nor ten-

By B. J. Bayles, J. A. Ford, M. J. Salkind

Unidirecltonally sulidijied AL-A13Ni was found to exliibit excellent microstructural stability to 508°C. Above this temperature the transverse micvostructure coarsened in a manner analogous to "Ostwald Ripening", but the A13Ni whiskers did not spheroidize or foreshorlen. The coarsened whiskers reinforced the matrix as effectirely as the finer whiskevs and no reduction in room-temperature tensile strength mas noled after exposure for 90 hr at 96 pel 0-1 the absollite melling temperature of the eulectic. The slability was auribucted to the presence of low-index (and presurrlably lor-energy) cvystallographic interjaces between phases. The driving force for microstructural coursening was presumed to be the reduction of interfacial energy between the phases. Finer micvoslructures were found to coarsen more rapidly than those which weve imitally coarser. FIBER-reinforced metals have been shown to exhibit good short-time tensile properties at elevated temperatures.1-4 However, many elevated-temperature applications require long-time property retention which dictates the necessity for microstructural stability. Two types of instability are common to fiber composities. The first, chemical instability, is due to chemical reaction between the matrix and the relnforcing phase. Petrasek and weeton5 have shown that chemical reaction between tungsten wire and several copper alloy matrices resulted in degradation of the reinforcing phase and reduction in strength of the composite materials. Kreider and Leverant4 have noted similar behavior for boron-reinforced aluminum above 400°C. The second type of instability arises in systems in which the phases are essentially chemically stable with respect to each other and is characterized by spheroidization and/or agglomeration of the reinforcing phase. parratt6 has reported this type of degradation to occur relatively rapidly at moderate temperatures for nickel and cobalt alloys containing whiskers of silicon nitride, aluminum oxide, and silicon carbide and has identified it as "physicochemical" instability. Although both types of instability are the result of the differences in the chemical potential between the fibrous phase and the matrix, they may be differentiated by the fact that the second type, "physicochemi-call' instability, results in little or no net change in the composition or amount of each phase present. It does, however, result in a morphological change which profoundly affects the strengthening mechanism. Chemical interaction. on the other hand, results in a change in the composition and amount of one or more of the phases present, or the appearance of a new phase. In the latter case, the appearance of the mi-crostructure, that of a fibrous phase aligned in a matrix, may remain essentially unchanged, but the chemical degradation of the fiber results in markedly reduced composite strength. This investigation was initiated in an attempt to evaluate the microstructural and related mechanical property changes of a whisker-reinforced eutectic composite after elevated-temperature exposure. The composite system chosen for this study was the uni-directionally solidified A1-A13Ni eutectic which Lemkey. Hertzberg, and Ford7,8 demonstrated to behave as a whisker-reinforced composite. The microstructure of the unidirectionally solidified material consists of aligned needles of A13Ni in a matrix of aluminum. EXPERIMENTAL PROCEDURE Eutectic ingots having a nominal composition of 6.2 wt pct Ni were produced by melting 99.99+ pct A1 and 99.99 pct Ni in recrystallized alumina crucibles in an argon atmosphere. The analyses of the starting materials are listed in Table I. These master heats were cut up? melted by induction heating, and unidirectionally solidified vertically in 1/2 -in.-ID. 6-in.-long graphite crucibles, in a dynamic argon atmosphere. Therma1 gradients in the liquid were determined by measuring the temperature in the melt as a function of apparatus travel distance, as discussed by Kraft and Albright.9 The rate of solidification was assumed to be equal to the uniform rate at which the crucible assembly was withdrawn from the furnace. Ingots representative of nominal growth rates of 2, 5, and 11 cm per hr were produced and the solidification parameters are summarized in Table 11. Ingots used for met allographic analysis were pre-

Jan 1, 1968

By H. Leslie Bullock

From aluminum to zirconium, the quantitative preponderance of quartz as a gangue material is well recognized. lf this material is to be efficiently removed, its variations must be understood. Variations with temperature are especially important. Too little attention has been given to the thermal polarization of quartz. Under closely controlled conditions, electrostatic upgrading is very reliable. For efficient separation, contact charges must be fostered and charges due to radiation, surface coatings, or thermal polarization avoided. This paper lists thermal transition points of quartz and shows their effect on actual separations. Simple separation tests with all factors except temperature held constant are recommended for determining transition points. With silica making up more than 27% of the earth's crust, its oxides comprising more than 59% of all igneous rocks, and quartz accounting for most of the main free oxides, the mining engineer is in constant contact with quartz, which may occur as a valuable mineral to be purified or, far more frequently, as a gangue material to be removed as completely and economically as possible. As a means of effecting such purification or removal, dry beneficiation is becoming more and more desirable owing to local water scarcities, wet waste disposal problems, or freezing conditions. One method that has been gaining particularly rapid acceptance is electrostatic beneficiation, or the separation of dry free-flowing materials by means of opposite surface charges, differences in potential, or differences in conductivity. Electrostatic beneficiation dates back to the 1870's, but only in recent years have newly developed methods and apparatus and a growing knowledge of solid-state physics widened the field for its economical application. Because the term "electrostatic beneficiation" has been rather loosely used in the literature, it has come to include both electrostatic and electrodynamic procedures. Attracting type separators, however, in which oper- ation is based on differences of surface charge or potential, are truly electrostatic, because the separation occurs in a substantially static field set up between oppositely charged surfaces. Separations with this type of equipment may occur at potentials as low as 1000 v and seldom require potentials as high as 30,000 v. In the new contact charge dielectric separators1 the variation in charge is produced by continuous contact and separation of the particles in the moving feed stream and these charges are fostered by the use of non-conducting support and feed surfaces and by handling the feed in the form of streams of appreciable depth. This favors uniformity of feed and allows higher production rates. The distinctive surface charge differences are set up on the separation of the particles according to Coehn's Law,2 which states that equal and opposite charges are generated on the separation of any two materials in contact and that the substance having the highest dielectric constant will be positively charged. The basic contact charge concept is reliable, but all electrical charges are transient and modified by the electrical conditions of the surroundings. Pyro-electric, photoelectric and radiant effects may modify or totally destroy the contact charges necessary for efficient separation, or contact with conducting surfaces may neutralize them. Such hostile conditions must be carefully guarded against, since they have led to many costly failures in the past. The most consistent difference in surface charges to insure good separation is produced by repeated uniform contact and separation of particles in the moving stream. The thickness of the feed stream possible with this method reduces the effect of contact with the supporting surfaces, but as some contact is inevitable, the best results may be assured by having the dielectric constants of the supporting surfaces between the dielectric constants of the substances to be separated. In general, the hard smooth surface of quartz makes it an ideal substance for electrostatic separation from most minerals. For instance, with calcite, starting with a feed containing 1.9% acid insolubles, one can produce a concentrate containing 0.30% acid insolubles with a tailings containing 21.7% acid insolubles and a yield of 92.8%. The color can be held at 92 or above and the tint at 1.7 or lower. Working with specularite iron ore, laboratory work has given a concentrate of 68.8% Fe., with an iron unit recovery of 96.7%. Excellent results are also in pros-

Jan 1, 1969

By K. I. Savage, S. C. Sun

This paper describes a process developed to recover coal, clays and pyrite from coal wastes. The process consists of fine grinding followed by coal and pyrite flotation which leaves the clays in the flotation pulp. A bituminous coal refuse containing 10% sulfur and 30% carbonaceous material was treated by this method to yield a coal product containing 4% sulfur, 10% ash; a pyrite product containing 45% sulfur (84% FeS2), 1% carbonaceous material; and a clay product containing 2% sulfur (3.5% FeS2). The coal yield was about 89%. The pyrite yield was about 77%. The process steps may be entirely flotation, or gravity separation (hydrocycloning) may be used to increase the pyrite : coal ratio in the flotation feed. Cost estimates for the process show a profit of $2.28 per ton of low pyrite grade refuse, but these do not include labor, maintenance, overhead and plant depreciation. The development of this process consisted of three parts: (1) exploratory tests, (2) op-timazation tests and (3) confirmatory tests. The objectionable qualities that sulfur imparts to coal have been commented upon from early times, and they have become more objectionable as the uses of coal have grown. In whatever form coal takes — raw, carbonized or gasified —the sulfur content remains objectionable, and therefore its compounds are removed as completely as possible. It has long been known that sulfur occurs in coal in different forms. In 1861, sulfur was said to exist in the state of sulfuric acid in combination with a base; in combination with iron as iron pyrites; as bisulfides of iron; and in combination with the organic elements of coal.' Pyritic sulfur is a term loosely used to cover the sulfur associated with iron in its various forms. The mineralogically recognized forms are pyrite (FeS2), pyrrhotite (Fe 1-x S) and marcasite (FeS2). The particle sizes of pyrites vary widely. Isolated grains of marcasite smaller than 15 microns have been found disseminated through coal.2 Hair-like "veins" of pyrite filling cracks in vitrain have been found. At the other extreme, lumps or nodules of pyrites large enough for removal by hand picking have been encountered. Organic sulfur, unlike pyritic sulfur, does not exist as discrete particles, but is instead intimately associated with the coal structure and thus it is impossible to remove it or reduce its concentration by physical or mechanical means.2 In the preparation of coal for its various markets, the pyrite minerals (pyrites) are separated from the raw coal feed. This separation process concentrates the pyrites in the tailings or other waste products. It would be desirable to recover these pyrites for three reasons: (1) Pyrites are potential sources of sulfur and iron. In 1967, for the fifth consecutive year, Free World consumption of sulfur exceeded production.3 Propelled by the shortage, the domestic price of sulfur has risen from $24 to $38 per long ton (bright). (2) The refuse, when placed in piles, becomes ignited. The pyrites (FeS2) bum, giving off SO,. Thus, the pyrites are a cause of air pollution. (3) Also, the pyrites undergo chemical reaction when exposed to air. The refuse is leached by waters which result in stream pollution due to the water-soluble iron and acidic reaction products. Coal refuse also contains coal minerals and clay minerals. Therefore, any process for recovering the pyrites must successfully separate them from the coal and clay minerals. In the study discussed here, ten different bituminous coal refuse samples were successfully upgraded in pyrite content. These samples represented a wide variety of coal waste materials from Pennsylvania and other states. The variabilities of the sulfur and coal contents are shown in Table I. The extremes are Sample J, a high sulfur-low coal, and Sample B, a low sulfur-high coal. Definitions of some of the symbols or terms used in this report are given below: Mesh size—Tyler standard mesh screen sieves with an opening based on the square root of two. Fe —Indicates iron, as determined by a stannous reduction-dichromatic oxidation method. S—Indicates sulfur, as determined by the ASTM "Eschka" method for sulfur in coal.

Jan 1, 1969

By C. Feng, I. R. Kramer

A study was conducted to determine the influence of the surface on the yield point of fcc metals and high-purity iron. For the high-purity fcc metals, the yield Point produced by restraining a specimen may be eliminated by removing a sufficient amount of the layer. A yield point similar to that in fcc metals was found when iron specimens were pre-strained after a prior deformation. This yield point is not due to an aging effect but is associated with the surface layer. The yield points in age-hardenable aluminum alloy and those connected with "work softening" are not affected by a surface-removal treatment and are, therefore, caused by bulk-type dislocation reactions. The yield point which appears in previously strained fcc metals has been the subject of numerous studies. Several theories have been advanced to explain this "unloading-reloading" yield point. Cottrell and stokes,' from their study on the effect of temperature on plastic properties of high-purity aluminum, considered that it was the result of an avalanche "breakdown" of Lomer-Cottrell sessile dislocations. Haasen and Kelly2 extended this concept of dislocation-dislocation interaction to account for the yield point when unloading and reloading was carried out at the same temperature. On the other hand, strain aging was found to be responsible for the yield point in A1-Mg alloy by Westwood and Broom,3 and in aluminum alloys containing various amounts of alloying elements by Smallman, Williamson, and Ardley.4 In these cases, the yield point is considered to be associated with the locking of dislocations by impurity atoms. Birn-baum and filer5,6 and Takamura and muira7 reported that, when a high-purity copper specimen was prestrained, then held at a lower stress, and finally reloaded at the prestrain temperature, a larger yield point was observed. Such an increase was attributed to the locking of dislocations by point defects. In addition, Bolling8 suggested that both mechanisms, i.e., dislocation-dislocation interaction and strain aging, are responsible for the yield phenomenon, at least in a brass. Thus, there appears to be experimental evidence for both the strain aging and dislocation-dislocation interaction theories to explain the yield point in the fcc metals and alloys. In a previous article,9 one of the authors observed that, if sufficient amounts of metal were electrolti-cally removed after deformation of a high-purity aluminum single crystal, the yield point did not appear upon reloading. Continued pursuit in this area revealed that the effect of the surface on the yield-point phenomenon is not limited to one metal but affects a variety of metals of different lattice structures. Nor is the effect limited to the yield points produced by simple unloading-reloading at constant temperature; the surface exerts an important role on the yield point even when the temperature is changed at some stage during the test. It is the intent of the present article to give additional information regarding the effect of the surface on the yield-point phenomenon and to show the association between the yield point in both fcc and bcc metals and the existence of a heavy concentration of dislocation in the region near the surface of a deformed specimen.10 EXPERIMENTAL Materials. The single crystals used in this study had a nominal cross section of 0.125 by 0.125 in. and a 3-in. gage length and were prepared by a modified Bridgman technique. The initial purity for the metals was 99.997, 99.999, and 99.999 pct for aluminum, copper, and gold, respectively. Bar stock of these same materials was used in the preparation of the polycrystalline specimens of aluminum and copper. The iron specimens were machined from rods of "ferrovac", reported to have a purity of 99.98 pct. In addition, a precipitation-hardening aluminum alloy, containing 1.5 pct Cu, 2.5 pct Mg, and 5.5 pct Zn, was used. The polycrystalline specimens of iron, copper, and the aluminum alloy had a diameter of 0.17 in. and a gage length of 2 in. while the high-purity aluminum specimen had a nominal rec-

Jan 1, 1965

By B. H. Kear, S. M. Copley

Stress-stvain curves are presented for Ni3Al (y') cvystals in several ovientations, deformed in tension and compression at constant displacement rate, at temperatures from 70° to 2000°F. Both the yield stress and wovk havdening increase with temperature, with the magnilude of the effect dependent on ovientation. The yield stress maximum occurs at 1500°F in [001], at 1400°F in [011], and at 1200°F in [111]. The suppression of the yield stress peak in [011] and [111] orientatiorzs is due to the onset of cube slip, rather than octahedval slip, a1 elerated temperatures. The temperature and orientalion dependence of work hardening in nominal single slip orientations corvelates with changes in the CRSS ratio for octahedral slip and cube slip, in agreement with a model for work hardening based on pinning of screw dislocalions by cross slip from an octahedral plane into a cube plane. It is concluded that the unique plastic properties of y' have a decisive influence on both ductility and strength characleristics of y +y' nickel-base superalloys. It has long been recognized that the strength of y + y' nickel-base superalloys depends on the precipitation of the y' phase [basically Ni3(Al,Ti)]. This paper presents new data on the strength characteristics of single crystals of simple y' (Ni3Al), and forms the first step in a systematic program aimed at elucidating the mechanisms of hardening in the complex commercial alloys. 1) EXPERIMENTAL PROCEDURE Single crystals of off-stoichiometric NiA1 were grown from the melt under vacuum by a modified Bridgman method. The melt was poured into a preheated alumina mold and crystal growth was promoted from one end by gradient cooling. The crystals were homogenized by annealing in hydrogen at 2400° F for 72 hr followed by furnace cooling. Chemical analysis of samples taken from several crystals gave an average composition of 88.2 wt pct Ni. Spectrographic analysis gave as the principal impurities in weight percent— Si (0.02), Mg (0.01), Fe (0.02), Ti (0.002), Cu (0.008), and Co (0.03). Tensile specimens with specifications as in Fig. 1 were prepared by a series of operations involving electrical discharge machining, precision grinding, and electropolishing. Compression specimens with dimensions 1/4 by 1/4 by -3/4 in. were prepared in a similar manner, except for the initial shaping operation using a precision cut-off wheel/two-circle goniometer unit to give selected crystal orientations. Specimens were deformed in a Baldwin-Wiedemann testing machine with furnace attachment, using a strain rate of 5 x 10-4 sec-1. The strain measuring device consisted of extension arms attached to the tensile grips (or compression plattens) at one end and leading out of the furnace to an LVDT at the other. Temperature was controlled by a thermocouple placed in contact with the specimen. According to the known phase diagram for the Ni/A1 system,' when an alloy of the specified composition is cooled from the melt, primary y (nickel solid solution) dendrites grow at the expense of the liquid phase, which becomes enriched in aluminum. At the eutectic composition the remaining liquid freezes as a two-phase mixture of y + y' (Ni3Al). Upon further cooling, a solid state transformation occurs, involving the precipitation of y' in the primary dendrites, and the complete transformation of the eutectic mixture to massive y'. The as-cast structure consists, therefore, of y + y' dendrites with interdendritic regions of massive y', i.e., transformed eutectic, Fig. 2. 2) DISCUSSION OF RESULTS 2.1) Stress-Strain Curves. Fig. 3 shows tensile stress-strain curves for crystals in orientations close to [001] deformed at temperatures from 70° to 2000°F. Both the yield stress and total elongation are strongly temperature-dependent. At 70°F, easy glide is absent, and the work hardening coefficient BIT - G/300. At T > 1500°F, the negative slope of the stress-strain curves is due to pronounced necking in the crystals. The yield stress maximum at 1500° F corresponds with a minimum in the ductility, Fig. 4. The extensive duc-

Jan 1, 1968

By J. C. Swartz

Measurements of the effect of precipitation stresses on the solubility of cementite (Fe3C) precipitates in a iron are reported. Solubilities were determined from measurements of the Snoek relaxation due to interstitial carbon after quenching from various equilibrium treatments. Stress-free precipitates were obtained by a spheroidizing treatment of vacuum-melted Fe 0.06 wt pet C. Subsequent equilibration treatments were designed to suppress nucleation of other precipitates. The results for stress-free cementite give a heat of solution of 14.8 i 0.2 keal per mole and an entropy change of 1.1 i 0.2 eu in the temperature range 400" to 715°C. Comparison with previous data indicates that the heat of solution increases about 6 keal per mole as temperature increases from 700" to 1000°C. Data on self-stressed cementite in quench-aged specimens of Fe 0.013 wt pet C indicate 1) an apparent heat of solution of 12.1 i 0.4 keal per mole in the range 280" to 690°C, 2) a strain energy of- 1.1 keal per mole Fe3C accompanying precipitation at 280°C, and 3') a gradual decrease in the strain energy of precipitation with increasing equilibration temperature. In com-parison with 2 and 3 the strain energy calculated for an isotropic model is 1.7 keal per mole Fe3C. The lower values obtained from the experiment indicated substantial stress velaxation by dislocation motion. WHEN a supersaturated solution of carbon in a iron is aged at temperatures in the range 200o to 700oC, the carbon clusters by interstitial diffusion and forms cementite (Fe3C) precipitate particles. Unstressed cementite has a volume per iron atom 9 pet higher than that of a iron;' hence, cementite precipitate particles are usually under pressure from the iron matrix. The pressure would tend to increase the solubility of cementite in iron.' This report describes anelastic measurements of the solubilities of self-stressed and stress-free cementite in a iron. Previous determinations of the cementite solubility are summarized in Table I. The method of cementite formation for each reference was studied to ascertain the state of stress of the cementite. The results judged to be for stress-free and stressed cementite are distinguished in the table. In the next section an estimate of the stress effect is obtained which is clearly too small to account for the large difference between the previous results in parts A and B of the table. THEORETICAL Let AGO be the standard free-energy change of the reaction Fe3C (eem.) = 3Fe (a) + C (in a) [1] in the absence of stresses. Since cementite precipitates appear to be rather pure10 and the carbon is so dilute in the iron,8 the cementite and iron of Eq. [ I] for the stress-free case have essentially unit activities and the activity of carbon equals its atom fraction xoC Then the stress-free equilibrium is expressed by RT In XoC = -?GO 121 To first approximation the change in the chemical potential of carbon due to the precipitation stresses equals the elastic strain energy W accompanying precipitation of a mole of cementite.2 Hence, in the presence of the precipitation stresses the equilibrium is described by RT In x sq = -?G° + W [3] where xsC is the mole fraction of dissolved carbon in the stressed case. An approximate value of W can be obtained from analysis of the inclusion problem in elasticity theory. The inclusion is a small portion of the matrix phase which has suffered a transformation while still imbedded in the matrix. In the absence of the constraint of the matrix the transformation would be equivalent to a uniform dilational strain eT. Both the matrix (a) phase and inclusion (0) phase are assumed to be homogeneous, isotropic materials. When the a and 0 phases have the same elastic moduli, which is approximately true for iron and cementite,11 the total strain energy per mole ß is12 2µVß(eT)2(3 +4 µx)-I [4]

Jan 1, 1968

By R. D. Burlingame, T. L. Joseph, Gust Bitsianes

DESPITE almost fifty years of commercial practice, the sintering of iron ore has received little fundamental study. Much of the theoretical work1-'has dealt with the constitution of sinter produced under widely varying conditions. While these studies have broadened our knowledge of the changes that occur in the sintering zone and in the freshly formed sinter during the early stages of cooling, they provide little insight into the changes that precede the formation of sinter. These preliminary changes merit study as a part of the overall process. Hessle. working with beds of Swedish magnetite concentrates, was one of the first investigators to study the sintering process in its entirety. On the basis of temperatures observed at various levels of the bed during sintering, he postulated a number of distinct reaction zones to account for the chemical changes leading to the formation of sinter. A more direct method of attack is that of arresting the sintering zone after it has progressed part way through the bed. A study of a vertical cross section through such a quenched bed provides direct information on the changes taking place at various levels. This method was used by McBriar et al.' to show that several well-defined zones of chemical change existed within beds that were typical of British sintering practice. The same general method of attack was developed independently in the present investigation to study partially sintered beds typical of American practice. Experimental Sintering Equipment The sintering operation was carried out on an experimental scale with the equipment shown in Fig. 1. The refractory-walled sintering chamber A was 11 in. deep and averaged 9 in. in diameter. Air was introduced through a tapered flow section B, which contained the orifice C for accurate metering of the incoming air. This section was located directly above the square ignition housing D, which in turn rested upon the sintering chamber A. The bed was ignited with burner E. The required suction for the operation was furnished by a fan F, which had an air capacity of 500 cfm (stp). Hot exhaust gases from the sintering chamber were cleaned in the dustcatcher G before entering the exhaust fan. In the study of partially sintered beds, it was essential to find some technique for removing the entire charge from the sintering pot without disarranging the unsintered bottom portion. This problem was finally solved by sintering the charge in a removable basket, which snugly fitted the sintering chamber. This basket was constructed of two thicknesses of window screen and was lined with a 3/16-in. layer of asbestos paper. The bottom of the basket consisted of two thicknesses of wire screen, which were fastened to the basket wall. For high fuel mixtures, additional insulation was provided by a somewhat thicker layer of asbestos cement. Preparation of Partially Sintered Mixtures The moist feed was carefully placed in the sintering basket, to prevent segregation of the particles, which varied widely in size and composition. A thermocouple was placed in the center of the basket with the hot junction halfway down, and the mixture was evenly distributed around it. During ignition and throughout the sintering of the upper half of the bed, the hot junction temperature increased very little. When the sintering zone reached the halfway point, as indicated by the sudden increase in the hot junction temperature, the charge was quenched. During quenching the suction was turned off and the orifice was tightly stoppered to prevent further influx of air. At the same time, nitrogen was admitted to the sintering chamber through the orifice tap. As soon as the nitrogen had displaced the air and products of combustion, the charge was removed from the sintering pot for immediate dissection. It is impossible to preserve the exact zone structure of the bed at the instant that combustion is arrested unless the downward transmission of heat is also immediately stopped. Fortunately, heat transfer is very slow in beds containing a stationary fluid, especially if the particle size is small. It follows that the minimum quantity of nitrogen should be used to displace the air and that static conditions be established as soon as possible. A very steep temperature gradient across the combustion zone for some time after the quench was evidence of in-

Jan 1, 1957

By G. H. Kesler, J. E. Oberele, C. E. Dryden, J. H. Oxley

Heat-transfer rates were measured in a model of a multifilament vapor-deposition bulb fo the preparation of high-purzty metals. Local transfer coefficients for heat transfer frow the filaments to the circuates process stream were determined as a functiol of gas flow rates and bulb, inlet, and filament, geowzetvies. These results a-e then convertted to n mass-t7,ansfer basis to provide a method of correlating vapor-deposition rates and to predict the performance of commercial urzits. The firm1 cor?,elating equation for mass transfer was found to be- wheve k, is the mass-transfer coefficient; D, is bze gas difficsivity : P is the system pressure; R is the gas constant; T is the gas temperature; Df, DB, and Di ave tlze diameters of the filament, bulb, and inlet, respectively; k is the gas conductivity; C, is the specific heat of the gas, M is the wzolecular zleight of the gas; Npr . N,,, NRe a7'e the Prandtl, Schmidt, and Reynolds numbem of the system, respectively; LB is the height of the bulb; and SB and Sf are the total suyiace area of the bulb and filaments, respectively. ONE of the more conventional methods of preparing very high-purity metals is the vapor deposition of the metal upon heated filaments. The reactions which can be employed in such a process generally fall into two classes: 1) Pyrolysis of a volatile metal compound. Generally because of their instabilities, metal iodides are used; however, other metal halides and hydrides have been employed. These processes are frequently carried out under vacuum conditions, and the filaments are maintained at high temperatures. 2) Hydrogen reduction of a volatile metal compound. A metal chloride is normally the preferred feed for these processes, but other halides are sometimes used under special conditions. These hydro- gen-reduction processes are usually operated at atmospheric pressure. Many of the current processes for the production of semiconductor materials are actually vapor-deposition processes. However, the vapor-deposition process itself is relatively old, and almost all metals can be prepared in a state of very high purity by the use of vapor-deposition techniques. Loonam has recently given an excellent review of the iodide process for metal deposition,' and Owen has started some detailed studies with a carbonyl system.' A more general treatment of all vapor-deposition processes has been outlined by Powell, Campbell, and Gonser.3 Despite the fact that vapor-deposition techniques have been employed since 1890, there is a surprising lack of fundamental information regarding the transport characteristics of even the simplest deposition system, the heated filament. The purpose of the investigation described in this paper was to extend some of the earlier data obtained at Battelle to predict deposition rates and the uniformity of deposition in large-diameter, multifilament deposition bulbs under forced convection conditions.4'5 A number of other investigators have already presented a simplified treatment of the deposition process under non-flow conditions, i.e., pure diffusion.6"9 To obtain information on the transport characteristics of a deposition bulb, a model of a typical plant deposition unit was constructed, and local heat-transfer coefficients from the filaments to a circulating air stream were determined under various conditions of air-flow rates and bulb, inlet, and filament geometries. These results were then converted to a mass-transfer basis, and consequently provided a method to correlate experimental vapor-deposition rates and to design commercial deposition units. EXPERIMENTAL WORK Description of Model. The apparatus which was used in this work was a scaled model of one type of deposition bulb. It was constructed of Lucite and was easily altered to give several combinations of diameter of bulb liner, inlet size and location, number of filaments, and outlet geometry. The model is shown in Figs. 1 and 2. The bulb shell was made octagonal for convenience in construction and observation, and the bulb liners were cylindrical. Air, introduced through one of several different jet inlets, was used as the test fluid in these model studies. Filaments for deposition of metal were simulated by metal rods 1/4-in. in diam. Two of the rods could be heated by passing electrical current through them ¦ while the remaining rods could not be heated. This procedure minimized the amount of heat which was

Jan 1, 1962

By J. Chipman, N. J. Grant, J. H. Walsh, T. B. King

WITH the development of adequate sampling and analysis techniques, much information has been obtained concerning the behavior of hydrogen in the steel bath during the course of steelmak-ing operations. From studies of this type it has become clear that the slag has an important role to play in determining the hydrogen content found in commercial products. A knowledge of the behavior of hydrogen in slags is necessary to round out our knowledge of hydrogen in steelmaking practice; with this information we are better able to assess practical methods of control. In this paper a method developed for analyzing slags for hydrogen content, studies of the solubility of hydrogen in synthetic slags, and studies of the variation of hydrogen content in slag and steel in industrial heats will be described. Previous Work—While very little has been done in the past to determine the hydrogen content of metallurgical slags, measurements have been made on such slag-like materials as geologic magmas and glasses. Goranson as made extensive studies of the solubility of water in natural and synthetic granites. Many workers have investigated the solubility of gases in synthetic and commercial glasses, but the recent work of Russell" is the most extensive. Russell found that the solubility of water in glass was proportional to the square root of the water vapor pressure in water vapor-oxygen mixtures. It was found that the solubility could either increase or decrease with temperature depending on the glass composition. Wentrup, Fucke, and Rief,' and Piper, Hagedorn, and Backes' have extracted hydrogen by holding a slag at 1300" and 800°C respectively in vacuum. Wentrup et al. reported hydrogen and water vapor as evolved together while Piper et al. passed the evolved gases from the hot extraction treatment over hot ferromanganese to reduce the evolved water vapor to hydrogen and, therefore, reported the analyses in terms of total dissolved hydrogen. Yavoiskii has reported hydrogen and nitrogen analyses on steelmaking slags. Dobrokhotov, Povol-skii, and Khan have studied the hydrogen content of basic open hearth steel under slags of varying viscosity. These authors reported that the hydrogen content of the steel bath increased as the fluidity of the slag was increased by the addition of bauxite. They recommended that a viscous slag be used and the steel tapped without deoxidation in the furnace to ensure a low final hydrogen content. Analysis of Slags for Hydrogen Development of Apparatus—The vacuum fusion analysis equipment described by Shields, Chipman, and Grant" was modified for the analysis of slags." This method depends upon the reduction of water in the slag to hydrogen, which is readily determined by the method used for hydrogen in steel. Preliminary experiments were made with a eu-tectic ferrosilicon melt as the reducing agent. Other experiments included the use of graphite and molybdenum crucibles. The ferrosilicon alloy bath was found to produce a thick coating on the furnace tube which could adsorb hydrogen. Graphite produced CO by the reduction of FeO, MnO, and SiO2 in such quantities that analysis for hydrogen was virtually impossible. Molybdenum, while giving a low blank value, could reduce the slag sufficiently to produce a volatile oxide which again was found to adsorb hydrogen. The arrangement finally adopted is shown in Fig. 1. The molybdenum sheet served as the induction-heated susceptor, and was separated from the escaping gases by alumina guide tubes. An outer jacket of alumina protected the quartz furnace tube, and alumina and quartz stools completed the assembly. The falling sample is shown wrapped in aluminum foil, 0.002 in. thickness, which acted as the reducing agent' This foil was careful'~ washed in acetone and an d and then dried in hot air before wrapping the weighed slag sample for charging into the apparatus. Investigation of the hydrogen content of the aluminum foil itself showed that a small quantity of hydrogen was released in vacuum, but had no relation to the weight of the aluminum charged. This quantity of hydrogen was

Jan 1, 1957