Search Documents

By M. Cohen, B. L. Averbach

Many hardened steels contain significant quantities of retained austenite even in cases where the carbon and alloy contents are low. In fact austenite has been detected in plain carbon steels containing as little as 0.50 pct carbon.1 Although the austenite may not be visible metallographically it causes definite dilatometric and magnetic effects during subsequent tempering or sub-atmospheric coo1ing.l,2,3 Therefore if the reactions which hardened steels undergo during later treatment are to be understood in quantitative fashion it is most essential to have some kind of absolute analysis for the austenite content in hardened steels. Once this analysis has been made, the austenite transformations can be followed precisely by observing such sensitive phenomena as changes in length or in magnetization but the latter techniques can only determine differences in the amount of retained austenite and usually an independent method must be found to put these differences on an absolute basis. In certain instances the microscope can be used advantageously to determine the percentage of retained austenite. The quenched sample is tempered to "darken" the martensite with minimum decomposition of the coexisting austenite, and then is polished and etched in the usual fashion. If the austenite is clearly distinguishable from the tempered martensite and other possible constituents its volume percentage can be measured quantitatively by point counting or lineal analysis.4 Such microscopic methods, however, depend on the etch being sufficiently discriminatory. In fairly coarse structures, if the austenite content is greater than 10-15 pct, there is probably little smearing of the etch, and point counting or lineal analysis seems to be quite accurate. On the other hand if the structure is difficult to resolve, as in commercially treated fine-grained . steels which contain less than 10-15 pct retained austenite, the latter may be completely obliterated by the dark etching martensite or it may appear disproportionately low as the interfaces between the two constituents become difficult to distinguish. Another disadvantage of the metallographic method is the need for "darkening" the martensite and hence the determination cannot be applied to as-hardened steels. The required tempering may spoil the structure for other tests or may even remove a small part of the austenite which is being sought. X ray methods hold more promise for covering the range under 15 pct retained austenite. Although austenite and martensite in the hardened steel may be chemically identical, their crystal structures and lattice parameters differ, and the intensity of an austenite diffraction line is some continuous function of the percentage of re-

Jan 1, 1949

By Will H. Coghill, P. H. Delano, G. D. Coe

Data concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as " grindability-index numbers," but grind-ability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pull'erized product by a method comparabLe with- commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulvcrizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation,it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-¾-inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horsepower-hours." The channel-roller pulverizer hereinafter described is believed to meet these requirements. History oF the Machine The, work started when Ralph W. smith, engineer, St. Genevieve Lime Co., St. Cenevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasive-ness of dentifrices,1 and it was thought the same principles might be applied to coal, Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By K. L. Sutherland, J. Rogers

The relationships between collector and mineral, activator and mineral, and activator, collector and mineral will be considered herein. We propose to criticize current theories of flotation but we will not repeat the many pertinent arguments presented by Wark and Cox28 in 1937 in which the "chemical" or more strictly the "solubility" theory proposed by Taggart and co-workers22 is shown to be untenable. Recently Taggart, Arbiter and Kellogg24 have studied the long-chain aliphatic amines as collectors and have attempted to resuscitate the solubility theory for these particular collectors. Dean and Ambrose3 have felt that "we stumble over words" when we distinguish different mechanisms of adsorption. Our view is that nothing is more stultifying to the development of a science than attempts to force widely different phenomena into one classification. This oversimplification leads immediately to difficulties in the interpretation of results. Experimental Procedure The response of minerals to activator and collector was determined by "captive-bubble" tests. The methods of preparation of specimens26 and of testingin have been previously described. Results from captive-bubble tests were confirmed by flotation tests in glass-stoppered cylinders.26 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±o.2 pH units and ±5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible by a cross and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, the experimental results being indicated on the figures by a square. The curves show the limits of composition of solution in which flotation in a cell would be possible. Many factors other than those considered in these tests determine recovery or grade of a given mineral in practice.

Jan 1, 1947

By W. A. Wood, W. H. Reimann, K. R. Sargant

A study is made of the microstructural changes produced in armco and pure iron subjected to alternating torsion at amplitudes above and below the knee of the S/N curve. The aim was to identify the basic mechanisms of fatigue and to find why they should give rise to a sharp S/N knee in contrast to the type of S/N curve shown by fcc metals. It is found that the basic structural change above the knee in the iron is a pronounced cell formation in the grains, which determines irregular micro-cracks, and below the knee a dispersion of fine slip that determines a dispersed pore formation in the grains. Comparison of these changes with those in fcc metals similarly tested shows that they do not include an intermediate structural change, a concentrating of slip in narrow bands with associated slip-band cracking, that characterizes the fcc metals and accounts for their different type of S/N curve. RECENT conferences on basic mechanisms of fatigue emphasize that fatigue damage takes many forms: for example, cracking in slip bands (Thompson1), at grain boundaries and inclusions (Hempel'), at precipitation zones in alloys (Han-stock, Forsythe), or at surface notch-peak effects, both hypothetical (Mott, cottrel16) and observed (Wood). Evidently it is not easy to see in this diversity a basic mechanism. At the same time the contributions suggest that some reconciliation may be possible if distinctions are drawn between three phases of the fatigue process: initiation of damage at nuclei, distribution of these nuclei, and the final macroscopic crack system. In initiation, the relevant features appear to be that nuclei may appear early, at least by 1/100th to 1/1000th of the life of a test specimen; that they may do so at many independent centers, appearing according to some observationsa as pores or voids; and that they are not necessarily self-propagating, damage spreading rather by their multiplication. In distribution, the relevant feature appears to be that they form preferentially in zones where the microstructure becomes abnormally strained (as defined more closely below). Now in these two phases the basic fatigue process should be systematic. But, at the same time, the "abnormal strains" in particular set the stage for considerable diversity in the final phase of macroscopic cracking, for where zones of abnormal strain develop will depend on what kind of fatigue deformation is applied and what kind of prior processing the test material has had. On this view it seems desirable to know what in

Jan 1, 1964

By Herbert Clark Hoover, Lou Henry Hoover

QUALITIES which the perfect miner should possess and the arguments which are urged for and against the arts of mining and metallurgy, as well as the people occupied in the industry, I have sufficiently discussed in the first Book. Now I have determined to give more ample information concerning the miners. In the first place, it is indispensable that they should worship God with reverence, and that they understand the matters of which I am going to speak, and that they take good care that each individual performs his duties efficiently and diligently. It is decreed by Divine Providence that those who know what they ought to do and then take care to do it properly, for the most part meet with good fortune in all they undertake; on the other hand, misfortune overtakes the indolent and those who are careless in their work. No person indeed can, without peat and sustained effort and labour, store in his mind the knowledge of every portion of the metallic arts which are involved in operating mines. If. a man has the means of paying the necessary expense, he hires as many men as he needs, and sends them to the various works. Thus formerly Sosias, the Thracian, sent into the silver mines a thousand slaves whom he had hired from the Athenian Nicias, the son of Niceratus1. But if a man cannot afford the expenditure he chooses of the various kinds of mining that work which he himself can most easily and efficiently do. Of these kinds, the two most important are the making prospect trenches and the washing of the sands of rivers, for out of these sands are often collected gold dust, or certain black stones from which tin is smelted, or even gems are sometimes found in them ; the trenching occasionally lays bare at the grass-roots veins which are found rich in metals. If therefore by skill or by luck, such sands or veins shall fall into his hands, he will be able to establish his fortune without expenditure, and from poverty rise to wealth. If on the contrary, his hopes are not realised, then he can desist from washing or digging. When anyone, in an endeavour to increase his fortune, meets the expenditure of a mine alone, it is of great importance that he should attend to his works and personally superintend everything that he has ordered to be done. For this reason, he should either have his dwelling at the mine,

Jan 1, 1950

By d&apos, L. Berenbaum, F. Heurle, R. Rosenberg

The structure of aluminum films obtained by evaporation was studied by electron microscopy, mostly by replica techniques and X-ray diffraction. The resistivities and stress conditions of the films were also determined. Film properties were studied as a function of source selection, substrate type, residual pressures of oxygen and water vapor, substrate temperature, and rate of growth. The formation of abnormal localized growths and whiskers resulting from annealing treatment subsequent to deposition was investigated. Films deposited onto single-crystal substrates were found to be epitaxially 0riented; for such films, relative orientations between films and substrates were determined. ALTHOUGH wide use has been made of evaporated aluminum films for the formation of conducting lines on semiconductor devices, relatively little has been reported concerning the structural characteristics of such films.1"9 The purpose of this study was to obtain an overall view of the dependence of these characteristics on film deposition and subsequent annealing conditions, which were similar to those used in silicon planar technology. Accordingly, most of this study was carried out using oxidized and bare silicon wafers as substrates, although some work was also done using alkali halide, magnesium oxide, and mica substrates. However, the main concern remained pragmatic. Emphasis was given to the study of the effects of deposition and annealing conditions on film characteristics such as structure, resistivity, and stress. I) EXPERIMENTAL PROCEDURES The films which were investigated in this study were deposited in 18-in.-diam glass chambers which were connected to the usual type of trapped diffusion pumps filled with silicon oil. Through the use of liquid-nitrogen-cooled Meisner traps and titanium sublimation pumps placed inside the deposition chambers, the pressure could be lowered to the lower portion of the 10- I Torr range and little increase in pressure would occur during the deposition cycle. Unless described otherwise, the substrates were 1-in.-diam p-type silicon wafers having a resistivity of 10 ohm-cm. The wafers were oxidized in wet oxygen at 975°C followed by a short dry-oxygen exposure at the same tempertture to a total oxide thickness of approximately 6000A. The wafers, backed by a layer of gallium, were mounted onto molybdenum discs brazed to a copper block.10 The latter was heated by imbedded commercial cartridge heaters. The substrate temperature could be maintained to within +10°C of a prescribed temperature during film deposition. The search for a satisfactory source for the controlled evaporation of aluminum has led to the use of 1-in.-diam crucibles" machined from rods of a commercially available, refractory composite* of Bn and

Jan 1, 1969

By B. L. Averbach, M. Cohen

Many hardened steels contain significant quantities of retained austenite even in cases where the carbon and alloy contents are low. In fact austenite has been detected in plain carbon steels containing as little as 0.50 pct carbon.1 Although the austenite may not be visible metallographically it causes definite dilatometric and magnetic effects during subsequent tempering or sub-atmospheric coo1ing.l,2,3 Therefore if the reactions which hardened steels undergo during later treatment are to be understood in quantitative fashion it is most essential to have some kind of absolute analysis for the austenite content in hardened steels. Once this analysis has been made, the austenite transformations can be followed precisely by observing such sensitive phenomena as changes in length or in magnetization but the latter techniques can only determine differences in the amount of retained austenite and usually an independent method must be found to put these differences on an absolute basis. In certain instances the microscope can be used advantageously to determine the percentage of retained austenite. The quenched sample is tempered to "darken" the martensite with minimum decomposition of the coexisting austenite, and then is polished and etched in the usual fashion. If the austenite is clearly distinguishable from the tempered martensite and other possible constituents its volume percentage can be measured quantitatively by point counting or lineal analysis.4 Such microscopic methods, however, depend on the etch being sufficiently discriminatory. In fairly coarse structures, if the austenite content is greater than 10-15 pct, there is probably little smearing of the etch, and point counting or lineal analysis seems to be quite accurate. On the other hand if the structure is difficult to resolve, as in commercially treated fine-grained . steels which contain less than 10-15 pct retained austenite, the latter may be completely obliterated by the dark etching martensite or it may appear disproportionately low as the interfaces between the two constituents become difficult to distinguish. Another disadvantage of the metallographic method is the need for "darkening" the martensite and hence the determination cannot be applied to as-hardened steels. The required tempering may spoil the structure for other tests or may even remove a small part of the austenite which is being sought. X ray methods hold more promise for covering the range under 15 pct retained austenite. Although austenite and martensite in the hardened steel may be chemically identical, their crystal structures and lattice parameters differ, and the intensity of an austenite diffraction line is some continuous function of the percentage of re-

Jan 1, 1949

By Erhard Hornbogen

Twins were propagated into large, well-annealed crystals of a, iron-phosphorous and a, iron-molybdenum solid solutions. Strain fields caused by interaction of these twins were made visible by precipitation. These strain fields can be explained by assuming that transmitted and reflected plastic waves are created when a twin strikes an obstacle with high velocity. The twin front itself can be regarded as a shear wave that may be able to develop a one-dimensional shock front. The occurrence of {WO} fracture by the reflected stress is also discussed. The described effects were not found when twins propagated at lout velocity into disturbed crystals, for example, into crystals previously deformed by slip. DEFORMATION twinning leads to shearing of a crystal lattice under external load. The shear appears to be homogeneous over a large number of crystal layers. In a iron, shear occurs on the (112) planes and in the <1ll> directions. The formation of a twin proceeds by the movement of partial dislocations that change the stacking at the twinning plane.l, In the bcc lattice, this partial dislocation can be created by dissociation of a sessile a/2[111] dislocation that lies in the (112) plane: Cottrell and Bilby&apos;s spiral mechanism can explain the homogeneous shear, but has not been proven experimentally. Nevertheless, this mechanism can explain the possible high velocity of formation of a twin. In Cottrell and Bilby&apos;s model, as in other models of twinning or phase transformation, a much higher energy is required to spread the first stacking fault than to add new layers by further movement of the partial dislocations. The dislocations will therefore become accelerated proportional to the difference between the stress, tN, to nucleate and tp to propagate the twin. It has been assumed3,4 that tn is the stress required to make two partial dislocations of apposite sign pass for the first time. After the first layer of new stacking has been formed, the maximum stress is TN=Gb/4pd where G is the shear modulus, b is the Burgers vector of the partial dislocation, and d is their perpendicular spacing so that the amount of shear is S = b/d. From this formula, a value of 25 kg per mm2 has been estimated for twinning in Zn3. The measured values are smaller, but local internal stresses may help to provide the necessary stress. For a iron, a higher value can be expected, mainly due to the higher value of G. That agrees with the observation that "burst" twinning occurs if the yield strength is in-

Jan 1, 1962

By A. A. Smith, J. S. Smart

THe elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses. When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range o to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorilv determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing 2nd oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B, and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold. The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300&apos; and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type. All samples were quenched from the annealing temperature in 10 per cent H²S04 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.&apos; Effect of Silver Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

By W. A. Krivsky, R. Schumann

Relaxation calculations were made to find the temperature distribution in the refractory wall surrounding a tuyere pipe. One set of boundary conditions approxiwated those of a standard copper converter while a second set represented a hypothetical,thermally insulated tuyere pipe. The pvonounced cooling effect of the tuyere is related to the problem of tuyere accretions and tuyere bunching. PARTICULARLY severe service conditions are encountered in the tuyere zone of a basic copper converter during the matte blow. High-temperature gradients result from the juxtaposition of the hot charge and the tuyere pipe carrying cold air. Refractory temperatures near the tuyere mouth vary rapidly with time when the blast is turned on or off. One of the most serious problems is the formation of magnetite accretions around the tuyere mouth, which occurs very rapidly under some operating conditions. As a result, continual punching of the tuyeres is necessary to maintain a satisfactory rate of converting. Thus, if some means could be devised for keeping the tuyere pipes fully open without necessity for punching, a considerable saving should result from reduction in labor cost, maintenance of full capacity operation, and reduction in refractory costs. Recent quantitative studies of the FeO-Fe,O,-SiO, system1 have shown that the solubility of magnetite in iron-silicate slags decreases rapidly with de- creasing temperature in the range of copper converting temperatures. Data taken from the previous work are shown in Fig. 1. Thus the formation of "horns" and accretions around the tuyere mouth can result simply from the freezing out of magnetite on the cooler areas of refractory immediately adjacent to the tuyere pipes. One might expect to find a correlation between the severity of magnetite formation and the area of refractory surface which is cooled below the freezing point of the slag (corresponding to magnetite precipitation). Magnetite itself has a very high melting point (1597°C) so that the accretions are for all practical purposes infusible. The accretions might be dissolved by increasing the silica content of the slag and at the same time raising the temperature, but this approach is not feasible because it results in rapid corrosion of the basic refractory lining of the converter as a whole. In order to understand better the problems involved in tuyere design and operation, it seems essential to have at least a semiquantitative idea of the thermal conditions in the tuyere zone. Accordingly, this paper presents results of thermal calculations for an idealized copper converter tuyere. These calculations follow the so-called relaxation

Jan 1, 1960

By I. Fatt

This paper proposes the network of tubes as a model more closely representing real porous media than does the bundle of tubes. Capillary pressure curves are derived from network models and pore size distributions are calculated from these curves. In this way is shown the difference between the true and calculated pore size distributions when the capillary pressure curve is used to obtain pore size distribution for porous media. INTRODUCTION Despite the technological importance of the laws governing flow through porous media, many of these laws have not yet been clearly formulated. This is especially true of the laws governing multiphase flow. The static properties, such as the capillary pressure curve, are also not at present interpretable correctly in terms of the pore size distribution and other structural properties of porous media. In the absence of any well founded theoretical description of fluid flow through porous media, many empirical descriptions have been proposed. In addition to the strictly empirical flow equa- tions, some equations have been developed rigorously from simple geometrical models of the pore spaces. These equations are only as valid as is the model used in their development. The two models used in the past, the sphere pack and the bundle of tubes, have been too simple, and as a result, the equations derived from them have failed to predict the observed properties. Agreement between theory and observation has been achieved for these models by inserting parameters of doubtful physical significance. The work to be reported here was undertaken in the belief that the study of a model more closely resembling most real porous media than does the sphere pack or bundle of tubes would yield useful information concerning the structure of real porous media and the relation between structure and flow properties. There was no intention of developing any calculational procedures, as for example calculating relative permeability from capillary pressure data. The objective of the study was instead to develop a better qualitative understanding of the relation between the various measurable properties of porous media. The model chosen for study is the network of tubes in which each tube represents a pore space in the porous medium. Microscopic observations leave no doubt that sandstones and clastic carbonates are three-dimensional irregular networks of irregularly shaped pores. The irregularity of these structures makes any accurate theoretical study of their properties impossible. Results from an oversimplified model such as the bundle of tubes are worthless when applied to real systerns. The sphere pack model, on the other hand, not

Jan 1, 1957

By William J. Craig, Harold L. Walker

INDUSTRY has for many years recognized the dependence of certain mechanical and physical properties, as well as workability, upon grain size variations in brass. Although the dependence of properties upon grain size has been recognized there are not many instances where a planned program of testing has been conducted and where the only intentional variable has been grain size. In particular the literature is limited with respect to the effect of grain- size on the endurance limit, though there are many industrial applications where the brasses are subjected to cycles of repetitive stresses. LITERATURE A number of the physical and mechanical properties of a given brass sheet, in the annealed condition, will depend upon: (I) The ready-to-finish grain size before final rolling, (2) the percentage deformation by cold working, and (3) the time and temperature of annealing, The first and second variables affect the recrystallized grain size, and the third variable affects the coalesced grain size. Gibbs1 has shown the effect of two different ready-to-finish grain sizes upon the tensile strength and hardness of deep drawing brass strip after a definite amount of cold rolling. The smaller the ready-to-finish grain size, the higher the tensile strength and hardness, but with lowered ductility, Gibbs also demonstrated, for a given time and temperature of anneal, that the tensile strength, hardness, and elastic limit are higher for the smaller ready-to-finish grain size, but the elongation is lowered, Townsend and Greenall2 have reported data which show that cold working increases the tensile strength, hardness, and load carrying ability of deep drawing brass sheet under reversed stress. Greenall and Gohn3 have reported data which show that the smaller grain sizes have higher tensile strength and hardness properties, and the data also show that increased cold working increases the tensile strength and hardness properties of deep drawing brass sheet. Kommers4 has reported data for tests of brass of known ready-to-finish grain size, a specific amount of cold reduction, and annealed at different temperatures above and below the recrystallization temperature. Kommers&apos; results indicate that annealing below the recrystallization temperature does not change the tensile strength and hardness properties, but the endurance limit may be increased from 22,000 to 28,000 psi. The increased endurance limit is explained as resulting from the reduction of internal stresses by a stress-relief anneal. Burghoff5 and associates have reported data on creep tests, over

Jan 1, 1948

By J. Rogers, K. L. Sutherland

The relationships between collector and mineral, activator and mineral, and activator, collector and mineral will be considered herein. We propose to criticize current theories of flotation but we will not repeat the many pertinent arguments presented by Wark and Cox28 in 1937 in which the "chemical" or more strictly the "solubility" theory proposed by Taggart and co-workers22 is shown to be untenable. Recently Taggart, Arbiter and Kellogg24 have studied the long-chain aliphatic amines as collectors and have attempted to resuscitate the solubility theory for these particular collectors. Dean and Ambrose3 have felt that "we stumble over words" when we distinguish different mechanisms of adsorption. Our view is that nothing is more stultifying to the development of a science than attempts to force widely different phenomena into one classification. This oversimplification leads immediately to difficulties in the interpretation of results. Experimental Procedure The response of minerals to activator and collector was determined by "captive-bubble" tests. The methods of preparation of specimens26 and of testingin have been previously described. Results from captive-bubble tests were confirmed by flotation tests in glass-stoppered cylinders.26 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±o.2 pH units and ±5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible by a cross and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, the experimental results being indicated on the figures by a square. The curves show the limits of composition of solution in which flotation in a cell would be possible. Many factors other than those considered in these tests determine recovery or grade of a given mineral in practice.

Jan 1, 1947

By Norman Brown, J. V. Rinnovatore

Substructures in explosively deformed and annealed ß brass have been examined by electron microscopy. In the explosively deformed condition, the structure contains a large density of straight screw type dislocations. Subsequent annealing up to 300oC produces low angle boundaries, which are characterized by superlattice dislocations, and expanded and contracted nodes. Evidence is given where two a(111) superlattice dislocations combine to form two a(001) superlattice dislocations. It is also shown that annealing at 400°C the networks disappear and that quenching from 400" C produces square and circular prismatic dislocation loops that lie on (100) and (111) planes, respectively. THE purpose of this work was to determine the effects of explosive deformation and subsequent annealing in a superlattice using electron microscopy. One of the first observations of explosively deformed structures was made by Hornbogen1 on a iron. Hornbogen found that screw dislocations were most prominent in the explosively deformed structure. He explained this result by suggesting that the edge components of dislocation loops move with the velocity of the shock front leaving a trail of extended screw components. Kressel and Brown2 observed explosively deformed Fe3A1, which is basically a body-centered type of superlattice in terms of dislocation geometry, and found that, as in the case of iron, screw dislocations were most prominent. It was also observed2 that, in cold-rolled and explosively deformed nickel, screw dislocations did not predominate, but rather a uniform network of dislocations was present in which the orientation of the dislocations was random. (Cell structures also have been observed by Nolder and Thomas3 for copper and by Johari and Thomas* for nickel). Kressel and Brown2 discussed the difference between dislocation morphology for bee and fee metals in terms of dislocation mobilities. They suggested that edge dislocations have a greater mobility than screw dislocations in bee metals but not in fee metals. Thus, the idea offered originally by Hornbogen1 is not valid since it should apply equally to fee and bee systems but does not. The results of recent work by Mikkola and cohens on explosively deformed Cu2Au are consistent with other observations for fee metals. They found that dislocations were randomly arranged but there was no significant cell formation. At high shock pressures, deformation twins are produced in fee metals.&apos; High pressures in bee metal should induce the bee — fee transformation while the metal is under pressure. EXPERIMENTAL PROCEDURE The Cu-Zn alloy used in this work contained 51.4 wt pct Cu. Specimens of 0.5 in. diam and 0.012 in.

Jan 1, 1968

By R. E. Reed-Hill, W. H. Hartt

The "(3034) " twin lamellae in magnesium have been reexamined using electron microscope replicas. The double twinning sequence (1011)- (1012) for these lamellae has been reconfirmed. Evidence is presented showing that the irrational habit of these twins is probably the direct result of a need to accommodate the second-order twinning shear. This accommodation vesults in both an external shear in the matrix and an internal shear in the lamella. A model is presented which accounts for the experimental obseruations. HCP metals are generally characterized by strong textures in which the basal planes of the grains tend to be aligned parallel to the rolling direction in sheet or plate and to the axis of wires and rods. Since these directions are normally those in which finished products may be subjected to uniaxial tensile stress, these textures effectively place the crystals of magnesium objects in orientations unfavorable to both basal slip and {1012) twinning, the easily activated deformation systems of this metal. However, when magnesium crystals are deformed near room temperature by a tensile stress nearly parallel to the basal plane, another mode of deformation can occur.&apos;,2 This is _a double twin which forms first by twinning on {loll), followed by retwinning on (1012). The resulting twin lamellae are of considerable interest. First, they can be responsible for "brittle fracture&apos;&apos;; when a tensile stress axis lies in the basal plane, because the reoriented crystal structure of a lamella is well-aligned for slip while the parent crystal is not. Extensive internal deformation may thus occur while the matrix is still almost undeformed. This deformation can produce a ductile rupture running the length of the twin.3 Complete failure of the specimen may then oc-cure by the spreading of cracks from one twin lamella to another, or by the movement of a crack into a grain boundary and then along grain boundaries. Since the the volume fraction of these doubly twinned elements is normally very small, the fracture may be classed as brittle, although the fracture mechanism is, of itself, essentially ductile. It is quite probable that the ductility transition, normally observed4 in magnesium at or slightly Obove room temperature, is closely associated with these second-order twins. The detailed relationship of these twins to fracture in single crystals will be the topic of another paper. The present paper is concerned with a second important aspect: the irrational habit of these double twins that falls close to {3034), or approximately 7 deg away from the primary (10il) twin habit. There is good reason to believe that this habit results directly

Jan 1, 1968

By L. F. Terry, H. K. Ihrig, D. J. Sabin, Ralph E. Davis

This paper presents the results of a study of the comparative values of the several fuels commonly used by industrial plants. It shows that the energy actually recovered from any fuel and turned into useful work is dependent upon several factors: (1) the total energy available in the fuel, (2) energy losses resulting from combustion reactions and (3) energy losses dependent upon the mechanics of the firing operation. The chemistry of combustion and the losses resulting therefrom are discussed. The Advantages and disadvantages of the several mechanical methods of firing and the resulting heat losses in each are developed. Data obtained from several typical fuel operations, where careful records have been maintained, are presented to show that the practical results in the actual operation are in harmony with the theoretical results developed in the earlier part of this paper. Water power and solid, liquid or gaseous fuels are at present the only commercial sources of energy. The economic utilization of any one of them depends, in the final analysis, on the cost of energy per unit of finished product to which the energy is applied. The location of the plant utilizing the particular fuel chosen is a large factor in the original choice. The cost per unit at its original natural source, or even in its delivered form, is not always the final measure of its worth. The use of electricity as a source of energy illustrates this to the extreme. Electric current produced from water power is very cheap in certain localities. In Norway, current is sold as low as ½0# per kw-hr., while in dry cells it costs as much as $10 per kw-hr. Yet the sale of dry cells is a large business. The selling price of gas also varies widely. In some localities natural gas for the manufacture of carbon black sells for as low as $0.02 per million British thermal units, while artificial gas for domestic purposes sells for as high as $6 per million B.t.u. Obviously the cost per unit of energy is not the final determining factor in its purchase. Any discussion of the economic utilization of fuels must include costs in relation to the units of finished material manufactured. In large central power generating stations, this is the over-all cost per kilowatt-hour, and in ceramic firing the cost per unit of finished product of a certain quality is the criterion of economic utilization.

Jan 1, 1931

By Walter Kauzmann

All viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.† Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem —i.e., the dependence of shear rates on temperature, stress, etc.—from the standpoint of .recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of app1ications.l Resolution of Macroscopic Shear into Microscopic Movements; Resemblance to Chemical Reactions Just as any large body is made up of many small units, or atoms, so macro-scopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for non-turbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove&apos; In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker14 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the plastic flow of crystalline solids from this

Jan 1, 1941

By J. R. Long, E. T. Hayes, D. C. Root, R. S. Dean

THE U. S. Bureau of Mines has recently reported on the development of a process for preparing pure ductile titanium in substantial quantities&apos; and on the physical properties that may be attained in the metal, when consolidated by powder metallurgy methods and fabricated by certain hot and cold-working procedures.2 The high physical properties (Table I), combined with excellent corrosion resistance and light weight, will lead no doubt to appropriate applications of the metal. In any application, methods of joining will be of considerable importance. The relatively high activity of the metal toward the common gases raises the question of weldability and conditions that might be required for successful welding. Since hydrogen, oxygen, and nitrogen embrittle the metal, it should be protected from these gases at elevated temperatures. This was demonstrated by a few preliminary trials of arc, gas, and resistance welding. In these trials only the resistance method proved to be immediately applicable. While atomic hydrogen welding of titanium may be successful in some instances, a considerable amount of development work will be required to prove its worth. In addition, it would be suited only to small assemblies that could be heated subsequently in a high vacuum to remove embrittling hydrogen. Heli-arc methods likewise would be limited to small assemblies, which could be completely protected by a helium atmosphere. It was quite apparent that titanium required more protection than was afforded by the normal flow of helium gas used for welding magnesium and aluminum. The hot metal is attacked by oxygen and nitrogen, and the rapid diffusion of the oxide into the metal prevents the formation of a protective coating and requires the helium atmosphere to be maintained until the weld has cooled nearly to room temperature. The preliminary work indicated that titanium could be successfully spot-welded without deterioration of the metal and that the microstructures of the welds were normal, exhibiting good bonding, and no oxidation. The high resistivity of titanium (53 microhms per cu. cm.) suggested that it would behave somewhat like stainless steel and allow considerable latitude in the several welding variables. The results reported here are intended to give a general picture of the effects of varying welding current, welding time, and tip pressure on single spot welds made on several different thicknesses of titanium sheet. The work was undertaken to demonstrate the feasibility of welding titanium rather than as an exhaustive study of spot welding. There are, therefore, a number of factors that will require further investigation to establish the specific controls required for actual applications.

Jan 1, 1946

The following paper, submitted by the Russian petroleum authorities, was secured through the courtesy of G. V. Ackerman, Vice President of Amtorg Trading Corporation, and N. V. Vannikoff, Representative in the U.S.A. of the United Oil and Gas Industries of the U.S.S.R. It gives an excellent view of the Russian petroleum industry as seen through Russian eyes. Noteworthy is the tremendous area over which the Russians are searching for petroleum, for this paper refers to such far-flung areas as the Arctic Tamir Peninsula, Kamchatka and Sakhalin on the Pacific, Lake Baikal in Central Siberia, the great new discovery at Neftadag in the plains of West Turkestan, and the oil of the Ferghana oasis, where the derricks look out over to the mosques of Kokand. Of interest also is the new pipe line to supply the industrial centers of Ukraine grouped around the great hydroelectric plant built at Dneprotroy on the falls of the Dnieper. The technical achievements have been noteworthy and we must pause to consider the scope of the undertakings being carried forward. Russia is at the worst a good second to the United States in petroleum reserves and for a long time to come will be a most important factor in the petroleum markets of the world. Her story should be of interest to everyone in the industry. The First Five Year Plan The first Five Year Plan, covering the period 1928-29 to 1932, accomplished the task of transforming the Union of Soviet Socialist Republics from an agricultural, backward land into a powerful independent industrial country, with an advanced technological foundation of its own for finally achieving the social reconstruction of the entire national economy. Along with the gigantic forward &apos;strides in industry and transportation, radical changes took place in agriculture. The creation of more than 5000 great state farms and of more than 200,000 collective farms serviced by a widespread network of machine-tractor stations has brought the U.S.S.R. to the fore as the largest agricultural country in the world. Imports of tractors and other agricultural machinery in the initial years of the Five Year Plan and the intensive output of this equipment by the great plants of the U.S.S.R. in the latter years of the plan have brought about the mechanization of agriculture in the Soviet Union. This year 250,000 tractors and 30,000 combines will operate in the fields

Jan 1, 1934

By A. H. Willis

In this paper the results of an exploratory study conducted by personnel of the Knolls Atomic Power Laboratory on 18.6, 22, and 40 wt pct uranium-zirconium alloy will be presented. LARGE power output and long life or endurance from small, compact nuclear reactors require the use of enriched uranium for a fuel material. However, the ability to remove heat from the element, the tolerable fission product concentration, or some physical limitation of the system can limit the allowable fuel enrichment, or the volume of the fuel. In such an event, the fuel-element designer must find a suitable diluent for the uranium. Zirconium is an attractive material for such a purpose as it has good nuclear properties and a low absorption cross section. Because it has a good corrosion resistance in water, zirconium is a suitable cladding and the uranium-zirconium alloy makes a good core material. The alloy has a high thermal conductivity, a low elastic modulus, and a low thermal-expansion coefficient, all of which tend to minimize the thermal stresses in the core. Furthermore, the unirradiated material is reasonably ductile and has adequate strength. DESCRIPTION OF SAMPLES Two types of cylindrical samples were used in this study 1) short, 1/2-to 1-in.-long samples to test the irradiation stability of the alloy and 2) 2-ft-long samples to investigate the resistance of an element to longitudinal deformation. Composite samples having 0.060-to 0.140-in. core diameters and clad with a 0.010-in. thick zirconium jacket were fabricated by coextrusion and by hydrostatic pressure bonding of the cladding to the preformed core material. Both fabrication processes produced the uniform metallurgical core-to-cladding bond which was felt necessary to minimize the uncertainty of the central core temperature. Both consumable-arc and induction-melting techniques were used to melt the uranium-sponge zirconium core alloy. Since a graphite crucible was used in induction-melting this alloy contained more carbon impurity, which resulted in a finer grain size than the arc-melted alloy. The core to cladding interface was uniform in elements coextruded from the fine-grain, induction-melted core material, while those elements fabricated using arc-melted core material had very irregular interfaces because of the coarser grain size. Both cold-worked and heat-treated fuel materials were irradiation tested. Cold-worked alloys were swaged to about a 5 pct final reduction in area without subsequent annealing. The heat-treated alloys were heated to 800°C, held at temperature for 15 min and furnace-cooled to about room temperature. This

Jan 1, 1960