Search Documents

By M. R. Annis

Drilling mud rheological and gel property changes due to elevated temperatures frequently cause problems in drilling deep wells. A laboratory investigation of the effects of time, temperatures up to 3001; and mud composition on these properties was made with concentric-cylinder, rotational viscometers of the Farm type. The viscometers were sealed from the atmosphere to prevent dehydration of the sample. Gel strengths were found to be more sensitive than viscosities to changes in temperature and mud cornposition. The high-temperature gel strengths of bentonitic clay drilling fluids were not predictable from low-temper.atl4t-e measurements. At high temperatures, [lie clay flocculates. The floccu-lation temperature depends on the concentration and type of solids in the mud and the degree of chemical defloccula-tion. As the bentonite content of a mud increases, floccrrla-tion temperature decreases. Lignosulfonnte treatment raises the flocculation temperature. To minimize adverse high-temperatrrre effects on mud properties, the mud should be maintainted at minimum solids content, properly treated with. a defloccullant which is stable at the maximum ten?perature encountered and maintained at a pH high enough to insure activation of the deflocculant for the duration required. The Methylene Blue Test for cation exchange cnpacity of a clay was found to be a useful guide in deter.niinirig when a mud contains a dangerously high clay conWnt. INTRODUCTION In drilling a well it is desirable, for several reasons, to know the effects of time and temperature on the rheological and gel properties of the drilling fluid in the hole. Problems associated with drilling fluids normally occur down-hole: so it is reasonable to be interested in the properties of drilling fluids at the conditions which exist down-hole. It has long been observed that high pump pressures are often needed to start circulation after a trip and that the "bottom-up" mud that is circulated back to the surface is usually more viscous than it was before "cooking" at the bottom of the hole for several hours. Burk-hardt' showed that a knowledge of rheological proper-ties of muds under down-hole conditions is necessary to predict pressure surges. He showed that the viscosity of a mud greatly influences the magnitude of pressure surges and the likelihood of lost returns. McLean et aL~ showed that the rheological properties of a mud under down-hole conditions are very important to cementing operations. This paper presents data showing the effects of time and temperature on rheological and gel properties of water-base drilling fluids. Measurements of gel strengths and rheological properties were made with two different concentric-cylinder rotational viscometers of the Fann type. One was the conventional six-speed viscometer modified to operate at temperatures up to 350F and at the vapor pressure of the liquid at test temperature. The other viscometer was newly designed to operate at temperatures up to 500F and pressures up to 1,000 psi. Tests with both instruments were made under essentially the same operating conditions. The new viscometer is shown in Fig. I. In this investigation, great emphasis has been placed on the rheological properties of clay suspensions, since clays are largely responsible for a mud's thixotropic and gel-

By J. Kucera, J. Vreštál

DIFFERENT authors1 ' have been engaged in meas-uring the vapor pressure of pure cobalt. The results of their measurements satisfy the expected temperature dependence of vapor pressure and are in mutual agreement, with the exception of the results by De Dyk Man and ~esmejanov.~ The latter authors, by using the effusion method, have achieved considerably higher values than other workers. By using the isotope exchange method they obtained much lower values than other authors. The determination of thermodynamic functions of the binary Ni-Co system was carried out, as far as we know, only by De Dyk Man and Nesmejanov.4 This determination was based on extremely low values of vapor pressure over pure cobalt obtained by the isotope exchange method. Therefore we considered it useful to repeat these measurements. Furthermore, the reliable values of thermodynamic functions should complement the migration characteristics, the inner magnetic field data obtained by Miissbauer effect measurements, specific heat data, and the K effect and positron annihilation characteristics that have been achieved for the Ni-Co system in the Institute of Metallurgy of the Czechoslovak Academy of Sciences in Brno.5-9 The measurements in this paper were performed by the isotope exchange method. In this method, as has been shown by analysis,10-'3 the vaporization rate, w, can be calculated from the relation w = k/1oSw [1] i0Sw) [1] where L, is the activity per unit mass of the source, S is the area of evaporation, k is the tangent at the point t = 0 to the curve giving the radioactivity de-pendence of the target vs annealing time, t, and wis the probability for the tracer atom condensation on the target surface. The value for cc. can be obtained from the equation w = a + 2P(l-a) [2] where P is Clausing's coefficient and a is the condensation coefficient. In the present work the cylinder shaped containers for annealing the samples were used, characterized by the ratio 1:d = 1.06. Here 1 is the length and d the diameter of the container. For this ratio P = 0.514 and w =0.5, and w is independent of the condensation coefficient. The vaporization rate is related to the vapor pressure p by the relation where R is the gas constant, T is the absolute temperature, and M is the molecular weight of the component investigated. Measurements of the vapor pressure of the i component over the pure metal, p!, and the alloy, pi, at the given temperature and composition enable one to calculate the thermodynamic activity of this component from the equation ai=pi/pi [4] is and the activity coefficient ri=ai/xi [5] xi where xi is the molar fraction of the investigated alloy component. EXPERIMENTAL Evaporization rate measurements were carried out with pure cobalt and eight different Ni-Co alloys, which were kindly delivered by the Centre National de Recherches Me'tallurgiques Liege, Belgium. The composition of the alloys is given in Table I. The cobalt used in these alloys contained the following impurities: 0.016 wt pct Fe, 0.014 wt pct Cu, 0.01 wt pct Mn. Other elements were present in much lower concentrations. From the melts, samples in the form of small cylinders of 12 mm in diam were ma-chined. The thickness of the targets and sources was 2.5 and 1.2 mm, respectively. The lower thickness of the sources was chosen to make their over-all ac-tivity as low as possible. Sources were activated in

Jan 1, 1970

By H. R. Ogden, E. S. Bartlett, A. G. Imgram

Notched and unnotched tensile specimens of wrought and recrystallized, oxygmted and hydro-genated tantalum and columbium were tested over a range of temperatures selected to encompass the ductile-to-brittle transition. Increasing the oxygen content of tantalum and columbium increased their strength, and raised their ductility transition temperature, but did not cause a marked deterioration of notch properties below that of commercially pure material. The adverse effects of oxygen were more pronounced for recrystallized structures than for wrought material. The effects of hydrogen are complicated by strain aging or slow strain rate hydrogen embrittlement at -105°F. However, in general, hydrogen had only a minor effect an strength, but markedly increased the effective transition tem-terature and caused a deterioration of notch properties . BCC metals including the refractory metals in Groups Va and VIa (V, Cb, Ta and Cr, Mo, W) can be expected to undergo a ductile-to-brittle transition and exhibit brittle fractures at low temperatures.' Notch embrittlement is associated with this phenomenon, and can be a serious design problem. Table I compares the tensile transition behavior and notch sensitivity of commercially pure Group Va and VIa refractory metals. The Group VIa refractory metals have considerably higher transition temperatures, and become notch sensitive at higher temperatures, than do the Group Va refractory metals. In addition, the Group VIa refractory metals are sensitive to metallurgical structure. Recrystallized structures generally have higher transition temperatures than wrought material of the same composition. The relatively poor transition behavior of the recrystallized structures of these metals is generally attributed to the segregation of interstitial impurity atoms at grain boundaries. Pronounced sensitivity to structure is not evident with commercially pure Group Va refractory metals, however. Since these metals have higher solubilities for interstitial elements than do the Group VIa metals ,4 it can be expected that higher total interstitial concentrations are necessary to develop a comparable degree of grain boundary segregation and to produce a similar sensitivity of transition temperature to structure. Increasing only the concentration of interstitial atoms in solution would tend to increase the flow stress of a metal in relation to its cleavage fracture stress and thereby raise its transition temperature, but would not be expected to cause a marked sensitivity of transition temperature to structure. A research program has been conducted at the Battelle Memorial Institute to evaluate the effects of interstitial oxygen and hydrogen on the transition behavior and notch sensitivity of tantalum and columbium, and to evaluate the effects of structure on "contaminated" material. EXPERIMENTAL PROCEDURES Notched and unnotched tensile specimens of oxygenated and hydrogenated tantalum and columbium with both wrought and recrystallized structures were tested over a range of temperatures selected to encompass the ductile-to-brittle transition Oxygen levels selected for study in both tantalum and columbium were nominally 500 and 1000 ppm, whereas nominal hydrogen contents were 150 and 500 ppm in tantalum and 150 and 300 ppm in columbium. Oxygen and hydrogen additions were made directly to 6-in. lengths of 1/2-in.-diam electron beam melted wrought bar stock, in a Sieverts Apparatus. Subsequent high-temperature annealing was required for homogenization of the oxygenated material, but was not necessary in the case of hydrogenated stock. The oxygenated and hydrogenated bars were then swaged to 1/4-in.-diam rods. Tensile specimen blanks were cut from the 1/4-in.-diam rods and annealed to achieve stress-re-

Jan 1, 1963

By M. Bevis, A. G. Crocker

A. G. Crocker and M. Bevis (Battersea College of Technology)— Richman and Richman and conard17 have recently published the very interesting results of their studies on the plastic deformation of Fe-Ni-C martensites and of an Fe-5 wt pct Be alloy. Other work on the range of Fe-Be alloys containing between 16 and 27 at. pct Be has also been reported by Richman." One of the fascinating features of this work is that the materials investigated deform primarily by means of twinning and that several twinning modes are operative in addition to the well-established (112 ) mode of bcc materials The composition planes of these unusual twins were determined using a single-surface analysis and reported as (0131, "{045)" or "{089)", and It is now thought1' that the "{0,1,13)" habit reported for the Fe-Ni-C alloys'' is more likely to be near "{127)". Although the full twinning elements of these unusual twinning modes could not be determined directly from the experimental results, the authors attempt to deduce the elements by considering twin intersectionslQ and by using the projection technique of Jaswon and Dove. The basic assumption of their approach is that the (013) habits are truly rational planes but that the other habits are irrational and merely approximated to by the indices quoted above. They thus deduce that the twinning mode describing the (013) habit is either Type I or compound and that the modes describing the other habits are Type 11. This deduction must however be false as all twinning modes in cubic structures obeying the classical orientation relationships of deformation twinning must be compound. Type-I and Type-I1 modes can occur in all of the other crystal systems (indeed in the triclinic system compound modes are not allowed), but in the cubic system only compound modes can arise. This fact, which does not appear to be well-known, fol- lows immediately from the relations between the four twinning elements defining a twinning mode. Thus for a Type-I mode which is uniquely defined by the rational twinning elements K1 = hi and given by: where the summation convention of the tensor calculus has been adopted. For cubic materials the metrics and reduce to the unit tensors and j so that we have It is clear from these equations that both ki and ui must take on integral values; i.e., Kz, and ql must be rational, if hi and vi are integers, i.e., if K1 and are rational. Thus for cubic materials a Type-I mode must degenerate into a compound mode and the same result also arises for Type-II modes. The apparently irrational habits observed by the authors can thus not be explained in terms of Type-I1 twinning if the classical laws of deformation twinning are to be obeyed. An alternative explanation of the irrational habits is that they may arise from twinning modes with four irrational twinning elements. These modes, which do not obey the classical orientation relationships associated with deformation twinning, have been shown to arise as the result of double twinning processes in magnesium,22 but may also describe a simple shear on an irrational plane in an irrational direction. Indeed double twinning processes in bcc

Jan 1, 1963

By Nick Holonyak

Halogen vapor-transport synthesis of Ga(As,-,Px) and its preparation into laser junctions are described. Electrical and optical properties of Ga(As,-,PX) laser junctions are discussed. The present limitations in these properties are related to material proble?vzs and the very early state of development of Ga(As,-,PX), and are discussed in this context. Inhonzogeneity problems, fluctuation of As :P ratio, and problems with deep-level contaminants are described and related to Ga(As,-,PX) junction performance. Laser junctions are demonstrated which operate to wavelengths as short as 6470 A (77°K). The prospect that Ga(As,-,P,) will operate to wavelengths perhaps 100A shorter is mentioned. IN this paper we wish to describe some of the more important features of almost 1 year of experience in the preparation and properties of Ga(As,-,P,) p-n junction lasers. Because much data so far available are far from complete, some of the results still must be considered tentative and subject to correction and revision as work on Ga(As,-,P,) crystal problems progresses. Although the electrical, optical, and device properties of Ga(As,-,P,) junction lasers are understandably of considerable interest, the work to date points out that by far the most serious problems extant and those deserving first attention are problems involving the growth, doping, and perfection of Ga(As,-,P,) crystals. One of the most formidable of these is to grow Ga(As,-,P,) sufficiently free of deep levels, either due to contaminants or to structural imperfections, to allow fabrication of laser p-n junctions which can be cooled and not suffer from "freeze-out" of carriers on deep levels (and consequent double-injection behavior). In addition to the problems of growing crystals adequately free of deep levels and generally of the highest perfection, so that the best possible laser junctions can be realized, the further goal remains of increasing the phosphorus content well beyond 40 pct in an attempt to determine the practical lower wavelength limits of laser action in the Ga(As,-,P,) system. Even though the laser junctions prepared in Ga(As,-,P,) are of importance in their own right, we have considered them at this point mainly a means to study the growth and crystal problems of the material. It can be concluded that the laser junctions now available are almost completely limited by the purity and structural deficiencies of Ga(As,-,P,) crystals, and cannot be fairly compared with, for example, GaAs p-n junction lasers until Ga(As,-,P,) crystal growth has been more extensively developed. The basis for the statements above will become evident in the following sections which describe Ga(As,-,P,) crystal and junction preparation, and laser-junction properties. G(As,-,P,) CRYSTAL GROWTH As previously reported,2 we have found it convenient to employ the halogen vapor-transport process3 for synthesizing Ga(As,-,P,) crystals for use in laser junctions. Commercially available GaAs and Gap, separately prepared by halogen vapor tranport, are sealed in the desired ratio in a quartz vessel with a quantity of column-VI donor and a small quantity of metal halide which supplies the halogen for transport. The sealed ampoule, as shown in Fig. 1, is heated at a temperature in the range from 1025" to 1100°C at the position of the source GaAs and Gap. The GaAs and Gap are simultaneously vapor-transported and deposited as Ga(As,-,P,) at one end of the ampoule

Jan 1, 1964

By R. Shuttleworth, R. Smith

A Knudsen effusion tnethod I~as been used lo measure the vapor pressure of pure iron in the temperature range 1000° to 1500°C. Neutron-irradiated , natural iron was used and the Mn'~proclzdced by the (n, p) reaction removed by evaporation at high temperature. The results can be represented by the equation: where pM - 1.088 x 107 atm and T, = 20,890°K. A value of 100.2 kcal per g- atom was obtained for AH;. THE vapor pressure of pure iron in the temperature range 1000" to 1500°C has been measured. Radioactive iron and a Knudsen cell technique were used and the Mn' produced by an (n, p) reaction removed by evaporation at high temperature. From the variation of vapor pressure with temperature values of the enthalpy and entropy of solid iron have been found. Previous workers2 used a Lang-muir method and measurements were made over a smaller temperature range than that in this work. EXPERIMENTAL The apparatus used was similar to that of Pyle and Shuttleworth, and McLellan and Shuttle worth. However, because of the higher temperatures the Knudsen cell was machined from tungsten bar and the flanged furnace tube was beryllia. Heating was by passing a high current (70 amp at 7 v for 1500°K) through a strip of tantalum foil laid across the top of the cell and through a turn of molybdenum wire around the furnace tube. This method of heating ensured that the top of the cell was slightly hotter than the base and prevented condensation and re-evaporation from the orifice. The temperature was measured by means of a pt/Pt 13 pct Rh thermocouple spot-welded to the base of the crucible. To ensure accurate temperature measurement the iron was in the form of a thin disc (0.75 cm diam by 0.075 cm) which lay on the base of the cell. The high-purity iron was irradiated in the Harwell pile for a week at a neutron flux of 1.2 X 10" neutrons per sq cm per sec. The isotopes fe'~ and Fe" are produced by (n! y) reactions but only Fe", half-life 45.1 days, is a emitter; Mn which is also a y emitter, half-life 300 days, is produced simultaneously by an (n,p) reaction.' Immediately after irradiation of natural iron the ratio of ~e" to Mn y activity was 100:l. However, manganese is very much more volatile than iron and almost all the y activity of the condensate is due to Mn'~. Thus it was essential to eliminate all the manganeses before any measurement of the vapor pressure of iron was made and this was done by preliminary heating for 20 hr at 1400°C. For each determination the iron was dissolved from the target with acid and the y activity compared to a known weight of iron. By means of a y-ray spectrometer the y-activity measurements were made at the 1.09-mev peak of the 17e5' spectrum where the background was of the order of 3 cpm. Despite the low specific activity of ~e" a mass of 10- " g of iron could be determined corresponding to a vapor pressure of about l0-'' atm. RESULTS The vapor pressures were calculated from the equation: Where m is the mass of iron effusing in a time t through an orifice of area a2, r is the radius of the target, Z is the distance from the orifice to the

Jan 1, 1965

By E. E. Anderson, R. L. Newacheck, J. Kohl

Radioactive materials were used underground before the advent of the nuclear reactor. Radium containing ores have been mixed with cements and other materials for later location in oil wells by gamma ray logging since 1940.1 Perforating bullets have been marked with radium salts,, and radioactive materials have been added to drilling muds to find the cause of "lost circulation."' More recently colloidal suspensions of radioactive cobalt-60 and silver-1103 and solutions of 1-1314 have been used in waterflooding operatiorns to determine injection profiles, flow paths and water velocities. In this paper a recent and interesting underground tracer application is discussed. Development work and field engineering were carried out under the direction of Tracerlab, lnc., with assistance from personnel of the client. A gaseous tracer, argon-41, was used in an attempt to determine the cause of leakage from an underground gas storage reservoir. STATEMENT OF PROBLEM This gaseous tracer application was carried out for the Natural Gas Storage Co. of Illinois. This company has developed an underground gas storage field 1,750 ft below the surface of the earth near the village of Herscher, Ill., about 60 miles south of Chicago. The total volume of gas stored in the field was estimated to be about 13 billion cu ft in the spring of 1954. The field has a maximum estimated storage capacity of 90 billion cu ft. The gas is contained in the Galesville sandstone, previously a water bearing formation of about 25 per cent porosity. The water as it is pushed out by the gas forms a barrier for the gas around the edge of the reservoir. Over the top and beneath the bottom of the reservoir are located several layers of impervious rock, which barring cracks or unplugged and unknown wells should act as seals. Twenty-one injection and withdrawal wells were drilled into the Herscher reservoir and gas injection was begun during the summer of 1953. After a few weeks of gas injection, evidence of gas leakage was detected at the surface; water wells began bubbling and losing prime, and dry spots in the fields indicated gas leakage from uncharted oil wells. In every case, the leakage could not be traced back any further than the water bearing formations a few hundred feet below the surface. An extensive search was made to locate uncharted oil wells which were believed to be possible channels for the gas from the storage formation to the water containing formation. Long-time residents in the area assisted in the location of several abandoned oil wells. The wells when located were cleaned out and either used as vent wells to relieve the gas pressure in the water formations, or were plugged with cement. None of the wells even approached depths which would endanger the soundness of the storage reservoir. All of the injection wells were tested for leaks in the casings by conducting neutron surveys and by other techniques. To detect any leakage up through the cement-filled annulus surrounding the casing, a section of the casing wall in one well was milled out. Then, plugs were installed above and below the cut-out section and pressure applied to the annulus, which proved conclusively that the cement was sound in that well. The well was then plugged with cement and abandoned. In another well, ammonia was injected into the well and a temperature log was made. It was hoped that a leak would be re-

Jan 1, 1956

By R. W. Olson, A. L. Benham

Viscous fingering was studied as it occurred in an open Hele-Shaw model (1 ft x 4 ft x 1/16 in.); it was also studied in the same model packed with 80-mesh glass beads during miscible displacements under unfavorable viscosity ratio conditions. It was determined that the lengths of 20 elements of the front were distributed normally around the average position of the combined elements under all conditions. Represented by the normal distribution, the length of the viscous fingers grew linearly with the distance traveled from the point of finger formation, increased with displacement velocity, and increased with increasing mobility ratio. Results obtained during the first few inches of displacement were of little or no use in predicting finger growth and/or finger length throughout the 4-ft model since the point of finger initiation cannot be predicted and would often occur several inches from the point of injection with either positive or apparent negative coordinates. The fingering occurring during a miscible slug displacement was much greater than would be predicted based upon the actual mobility ratios between in-place fluid and slug and between slug and following fluid, using the results described above for miscible displacement in the absence of a slug. Many of the experiments in the packed model showed that the rate of growth of the viscous fingers was diminishing toward the end of the displacement in the 4-ft long model, indicating that microscopic mixing, such as diffusion or dispersion, was decreasing the viscous fingering effect. INTRODUCTION Viscous fingering is a manifestation of a finger-shaped interface between displaced and displacing fluids occurring during typical miscible displacement projects for oil recovery. Its cause may be traced to the instability of a viscous fluid being displaced by a more mobile fluid. Viscous fingering takes on important significance in the miscible slug process 1.2 where it may be a dominant factor in determining minimum slug size. Experimental1-3 and theoretical4-7 studies of viscous fingering have been made by other investi- gators. However, an exhaustive study of the variables affecting viscous fingering had not been made. The present study was undertaken in an effort to determine the effects of some of the more obvious variables—such as mobility ratio, displacement velocity, distance displaced, and packing—upon viscous finger length and growth in a small laboratory model. It does not necessarily follow that conclusions reached by studying the results of this model study may be applied to the field. Future studies would have to evaluate the effect of model size on extension of these results. EQUIPMENT AND EXPERIMENTAL PROCEDURES A flow diagram for the equipment used in this study is shown in Fig. 1. Basically, it consisted of (1) a constant-rate pump for the injection of displacing fluid into (2) a model made up of two flat transparent plates spaced a small distance apart and (3) provisions for the production of fluid into a calibrated graduate. The displacing fluid contained a dye which allowed visual observation of finger spacing and length. The pump performed at rates from 2.5 cc/hr to 480 cc/hr, while pumping a light mineral oil into a bladder in a closed glass container holding the displacing fluid. The model was made up of two plates of 1-in. Plexiglass with dimensions 1-ft wide by 4-ft long. These were spaced 1/16 in. apart so that the internal model dimensions were 1-ft wide x 4-ft long x 1/16

By P. G. Meikle, C. T. Holland

The effect of the condition of friction upon the ultimate unit compressive strength as determined between the compressed faces of precisely machined coal specimens and specially prepared testing platens has been examined. Reductions of 30 to 40% in the ultimate unit compressive strength of these model coal pillars have been verified when lubricants areused between the faces as compared to non-lubricated faces. Increase in unit compressive strength due to confinement at each of three levels of friction appears to follow generally the widely accepted "1/2 power law", i.e. S - C (L/T)1/2 where S is the unit ultimate strength, C is a constant dependent on the coal being tested and the coefficient of friction acting at the compression surfaces and L and T are the least width and thickness of the specimen, respectively. Results suggest that the surface condition of both the specimen and platens should be mentioned in detail in conjunction with compression testing, for although the term (L/T)1/2 is adequate for all practical purposes, the coefficient C is directly dependent on the condition of interfacial friction, all else remaining constant. One phase of the investigation of the confining effect of friction on the ultimate unit compressive strength of small coal specimens has recently been completed at the School of Mines of West Virginia University. The efficient control of ground is of fundamental importance to successful mining operations and the design of support pillars has always presented the mining engineer with a difficult and intriguing engineering problem. Since about the turn of the century, many investigators have performed extensive laboratory tests on small coal specimens in efforts to solve some of the perplexing problems of strata control and pillar action in coal mines. A detailed review of this work would serve no purpose here, but a brief mention of the more significant contributions is in order. Muller16 was perhaps the first to illustrate the effect of confining pressure on the strength of coal specimens in compression. His work has recently been more carefully expanded by the experiments of Murrell17 in Great Britain. Rice and Enzian l9 observed that as the size of cubical test specimens increased, the unit compressive strength decreased. These observations were later supplemented by Lawall and Holland, 13 by Greenwald4,5 et a1 at the U. S. Bureau of Mines, by Gaddy3 as well as by Steart,22 Millard15 et a1 and Evans2 et al. Gaddy3 seems to have been first to quantify this relationship with his equation: S = K/vd , where S - ultimate unit compressive strength (psi), K = a constant dependent on the coal, and D =edge dimension (in inches). Holland7 concluded that the strength of coal as affected by lateral dimensions and thickness could be expressed as where K = a coefficient dependent upon the coal, L = least width of pillar (in.) and T = thickness of pillar (in.). Data supplied by this formula have been compared to the estimated stresses in pillars that had been standing for long periods in coal mines and in the cases so far studied the results indicate that the formula predictions are sufficiently accurate for engineering purposes (Holland11 ). This equation therefore is believed to be the simplest and most accurate tool available at the present time for approximating the strength of a coal pillar (over a specified range of L/T) in situ. However, Holland7,9 has indicated that friction between the coal pillars and the top and bottom rock

Jan 1, 1965

By Guy Borden, Michael J. Rzasa

Laboratory data on bubble point pressures and reservoir volume factors have been correlated as functions of solution gas-oil ratio, calculated gas gravity of the pentanes-and-lighter fraction of the entire fluid, differential residual oil gravity, and reservoir temperatures. INTRODUCTION Several correlations of crude oil properties have appeared in the literature. D. L. Katz4 in 1942 presented five methods of predicting oil shrinkage. these being of decreasing accuracy for decreasing amounts of information available. M. B. Standing- in 1947 published three correlations of laboratory flash vaporization data of California crudes. From values of GOR (gas-oil ratio), gas gravity, liquid gravity, and temperature, his correlations will predict bubble point pressure, formation volumes of bubble point liquids, and two-phase formation volumes. Curtis and Brinkley2 in 1949 presented several correlations. From the gas-oil ratio, an approximation of reservoir volume factor and barrels of condensate recoverable per barrel of reservoir space may be obtained; along with liquid gravity and reservoir temperature, the GOR will allow prediction of bubble point pressure. These last cor- relations seem to be more qualitative than quantitative. Generally, laboratory bottom hole sample tests furnish information on solution gas-oil ratios, residual oil gravities. bubble point pressures, viscosities of oils, liquid shrinkages, and occasionally gas gravities. Each of these data has its own applications and use in reservoir engineering calculations. The particular uses of correlated bottom hole sample data are found in (1 Providing a basis for obtaining estimates of formation crude properties in fields where bottom hole sampling is impractical or impossible. (2) Greatly reducing the time in obtaining the desired information. (3) Determining the applicability of the results from various bottom hole samples to particular field problems. (4) Avoiding, in many cases, the uncertainties of sampling by replacing it with an element over which greater control can be exercised. (5) Permitting use of preliminary field data in application of production procedures before a bottom hole sample can be obtained and analyzed in the laboratory. (6) Serving as a check on data which may appear out of line. (7) Estimating for a particular type crude the appropriate equilibrium constants by working backward from the bubble point pressure. (8) Estimating original or other past history properties of reservoirs that were not sampled in the past. PROCEDURE Application of the published correlations4,6 to Stanolind laboratory data indicated that the general scheme presented by Standing" could give dedrable results if changes were made in parameter positions and scales. The correlation curves were drawn with all the variables having consistent gradations except the temperature increments which were drawn in to best fit the data. The variables from available Stanolind laboratory data are defined below: (1) Gas-oil Ratio: Gas is liberated at reservoir temperature by differential vaporization (or rather by a series of flashes, approaching differential vaporization) and measured at atmospheric pressure and temperature, at which the compressibility factor is assumed to be unity. The oil is the residual liquid remaining after the pressure has been reduced to atmospheric. For the gas-oil ratio both volumes are corrected to standard conditions of 14.7 psia and 60°F. (2) Gas Gravity: It was decided to arbitrarily divide the hydrocarbons of the entire bottom hole sample into pentanes-and-lighter and hex-anes-and-heavier, and use a calculated gas gravity of the pentanes-and-lighter for a correlating variable. (Sample calculation is shown in Table 111.) (3) Liquid Gravity: This is the API gravity of the residual liquid from the differential vaporization. The gravity is measured at room temperature and corrected to 60°F.

Jan 1, 1950

By I. W. Alcorn

THE cost of drilling in the past few years of proration and ever decreasing allowables has received increasing thought and study. It seems to parallel the strides made with respect to pumping problems in 1932 and 1933. Low profit margins stimulate the search for economies. Any discussion of slim-hole drilling involves a multitude of abstract values, and the problem can be attacked only by a study of records and rational thinking. In a measure, traditional methods must be studied with a questioning attitude. The words "slim hole" may be somewhat misleading, as the term is entirely relative. For that reason I wish to define it as used in this discussion. On the Gulf Coast, I would define a normal hole as one in which 10 3/4-in. surface casing has been set and below which a 9 7/8-in. hole is dug. With this as a datum, holes of larger diameter below surface would be called "large holes," with 12 1/4 in. as the "extra large" class and holes of smaller diameter classed in the slim-hole range, 6 1/4 in. representing about the minimum size. The optimum size has not been definitely determined, but the preference is for a program that would call for setting 8 5/8-in. surface casing and digging a 7 3/4-in. hole. Different sections of the country might very properly deviate from this practice because of differences in depth, formations, regulations, or other factors. This paper will be confined to a discussion of the drilling of exploratory wells, as the drilling of this class of wells is quite a different problem from that of drilling a proven field, although many of the same considerations apply in both cases, as will be apparent. Although for many years shallow slim-hole and core-test holes of small diameter had been dug, it was not, I believe, until the fall of 1937 that serious consideration was given to its application in drilling wells 7000 ft., 8000 ft. and 9000 ft. deep on the Gulf Coast. This does not mean that nearly all such wells drilled on the Gulf Coast now are of the slim-hole variety, but only that efforts have been aimed in that direction with very encouraging results and there has been a very definite trend to reduce the size of holes, a trend that probably will continue. As to exploration policy, there appear to be two distinct and opposite views. The one usually followed in the past was more or less designed to "shoot the works" on one well. Generally on the Gulf Coast, the depth at which production might be obtained is limited by the drilling equipment and economics. With this thought in mind, wildcat wells are often planned with the idea of carrying the depth to 10,000 ft., or even 15,000 ft. All of the possible hazards are anticipated and the general drilling and casing programs are so predicated. Such wells contemplate the drilling of large-diameter holes; the setting of at least one protective string of casing and an extensive coring policy, all of which finally adds up to an expensive well. As opposed to this general policy is the slim hole. This, on the Gulf Coast, recognizes that new discoveries represent gam-

Jan 1, 1941

By Charles H. Thurman

The data given herein were first included in a paper read before San Francisco Section, A.I.M.E., in October 1940, and are applicable to conditions existing until the gold-dredging industry was temporarily suspended by Order L-208 of the War Production Board in the fall of 1942. There is no doubt that gold dredging will be resumed at some future time, and on a scale equivalent to that of the recent past, but the cost data given herein will be affected to some extent by conditions existing at that time, and by labor rates and prices for materials then prevailing. Dragline vs. Bucket-line Dragline dredges should not be considered for mining large areas of low-grade placer gravel. In such deposits a dragline operator with a 5-cu. yd. dragline would be doing well to maintain an operating cost of 6¢ per cu. yd., while a bucket-line dredge with buckets no smaller than 7 cu. ft. each could be operated for less than 4¢ per cu. yd. By operating costs, I mean only field charges such as direct operating and overhead, which includes pay roll, power or fuel, repairs and maintenance, insurance, land clearing and general expenses, but not including such items as prospecting, depletion, depreciation of equipment, State Franchise Tax, or Federal Income Tax. It is not to be inferred that a dragline dredge cannot make a profit in small low-grade deposits, where the extent of a given property is too small to justify the use of the more costly bucket-line dredge. Consider small deposits of 106 gravel. It is obvious that a deposit of 5,000,000 cu. yd. of such gravel could not be mined profitably with a new 7-cu. ft, bucket-line dredge, costing upward of $250,000, and in operation costs at 4¢ per cu. yd., paying for land or royalties out of earnings; nor could a new combination 5-cu. yd. dragline and washing plant, worth upward of $125,000 and working at 6¢ Per cu. yd., make a profit. These comparisons are made because the hourly capacity of both types of dredges is nearly the same. The bucket-line dredge averages 93 per cent operating time in 24 hr., as against about 80 per cent or less for the dragline dredge. These Percentages of operating time are important factors in making a comparison of this kind- The bucket-line dredge has greater efficiency in cleaning soft bedrock, usually characteristic of dredging deposits, and a 7-cu. ft. bucket-line dredge can be efficient to a total digging depth of 80 ft- (65 ft. below water, 15 ft. above). A 5-cu. Yd. dragline dredge is limited to about 30 ft. of efficient digging depth, 5 ft. of which could be above water. In small areas of gravel not over 30 ft. deep, a 5-cu. yd. dragline dredge could make a profit where a bucket-line dredge could not do so. As an example: compare the dredging of 3,000,000 cu. yd. of 10 gravel 28 ft. deep with bucket line, costin 4¢ Per cu. yd., and with a 5-cu. yd. dragline dredge operating at 6¢ Per cu. yd. Because of small yardage, new equipment is not warranted, therefore we can assume that the dredges of both types are used equip-ment, fully depreciated. Dismantling, mov-

Jan 1, 1946

By T. R. Ingraham

When aluminum sulfate was decomposed in an evacuated apparatus and the sample cooled, Q alumina was found. The thermodynamics of the decomposition reaction were resolved by measurements of the total pressure of SO3, SO2, and O2 generated over the sample at various temperatures. The results were correlated with other published data to calculate the rmges of thermodynamic stability of the various compounds involved. The thermal decomposition of aluminum sulfate was studied by Wijhler, Pluddeman, and Wöhler1 and by Warner and Ingraham.2 The results of both studies were critically reviewed by Kellogg,3 who observed that "each set of data shows considerable scatter and strong curvature on a plot of log pso3 vs 1/T".3 He agreed with Warner and Ingraham2 that both the discrepancy in the two sets of results and their curvature may arise from the indefinite properties of the particular form of A12O3 which is formed during the decomposition. While studying the thermal stability of other sulfate systems, we had noted the presence of nonequilibrium oxide properties in both the cobalt4 and manganese5 systems, but neither had shown any appreciable curvature on a logPSO, vs 1/T relationship, and the data from both systems agreed reasonably well with prior work. It therefore seemed reasonable to reexamine the technique which had been used in our earlier work on aluminum sulfate.2 The principal difference was that a tightly compacted pellet had been used for the earlier aluminum sulfate work, whereas a loose powder, contained in a platinum boat, was used for our work on other sulfate systems. In addition, a better technique had been developed for dehydrating the samples. From work done on the nickel system,6 we had become aware of the highly protective nature of some sulfate layers on their oxjdes, and hence of the necessity of providing a large surface area of P3e sample when equilibrium was to be attained in a reasonable time. That observation suggested that perhaps a steady state, rather than equilibrium, had been reached in the earlier work on aluminum sulfate. This paper reports a repetition of the experimental work with large, finely divided samples of anhydrous aluminum sulfate. APPARATUS AND PROCEDURE The apparatus used in the experimental work was described in earlier papers.2,7 The source material was Anachemia reagent-grade Al2(sO4)3 - 18H2O which was first partly dehydrated by heating at 400°C for 48 hr and then completely dehydrated by repeated baking of an aluminum sulfate-oleum slush to dryness at 450°C. ? Alas was prepared by decomposing some of the sulfate in a muffle furnace at 800° C overnight. Approximately equal amounts of the 7) alumina and aluminum sulfate were used in the experiments. The finely divided samples were handled under dry box conditions, and in addition some of the aluminum sulfate was decomposed in the apparatus while it was under vacuum, to ensure its complete dehydration prior to sealing the apparatus. The samples were heated to a series of constant temperatures on both increasing- and decreasing-tem-perature programs. Two to three days were required to obtain steady readings of the total decomposition pressure on an increasing-temperature program, and 5 to 6 days on a decreasing-temperature program. Three samples were examined on both programs. Within experimental error, the results for each sample and each program could not be distinguished.

Jan 1, 1969

S. Tandanand, Twin Cities Mining Research Center, U. S. Bureau of Mines As an addition to the fine reviews on drilling presented in the foregoing papers, we feel it would be appropriate to mention briefly some work in this area by the U. S. Bureau of Mines. The Bureau has had under way for several years at its Twin Cities Mining Research Center studies directed toward a better understanding of basic drilling mechanisms. The work includes drillability investigations with diamond rotary, and with percussive drilling systems, as well as fundamental studies of rock behavior under drill bit types of loading. Results of our work to date have contributed the following to the state of the art. MECHANISM OF ROCK FAILURE-Rock fragmentation through use of mechanical energy systems, including drilling systems, consists of two major components-machine and rock. The two components are related to each other by their functional behavior and their resultant motion which the components mutually influence. Forces in the systems are transmitted directly to the bit which in turn induces stresses in the rock. When the induced stresses exceed the strength of the rock, the rock fails resulting in penetration. Rock strength is a function of the forces applied to the rock. Stresses under a drill bit, regardless of bit configurations, are essentially compressive, resulting in a condition where the rock has the highest resistance to failure. The ratio of principal stresses induced under drill bits is an indication of the mode of failure in the rocks. Initially, compressive stresses under the drill bit cause rock to undergo inelastic deformation. The impression observed at the first stage of crater formation under the drill bit shows that rock is no longer elastic. Associated subsurface failure at this stage precedes total rupture which subsequently appears at the rock surface. Thus, explanation of crater formation, by applying theory of elasticity alone, is likely to be over-simplified. ENERGY VERSUS VOLUME OF ROCK REMOVED-Experimental results show that energy per unit volume of rock removed is constant for a particular rock and bit type. Rock offers a definite resistance to penetration, depending on the method of the energy application; this may be defined as the drilling strength of a rock. Energy consumption in a drilling system may be divided into two components: 1) Energy required to move the machine parts; and 2) energy consumption in breaking rock. Component 1 is dependent on the type of the machine. Component 2 is dependent on the strength properties of rock and the efficiency of the bit in rock cutting. The sum of the energy required in both components determines the total energy required in breaking rock. Our work in this area has included consideration of both diamond and percussive drilling systems. PENETRATION RATE-For a drilling rate expression to be useful in predicting field performance, it should include the operating characteristics of the drilling machine. Eq. 37, for example, is simply a statement of the fact that the drilling rate is determined by the power output of the machine (2pNT) and the power requirements to break the rock in the hole (AER). In order to predict the performance of a particular drill and the effect, for example, of the rotary speed, on the drilling rate, R, Eq. 37 must be modified to include the

Jan 1, 1967

By G. H. Tausch, T. A. Huber

Very encouraging progress has been made ill the develop-ment of the permanent-type well completion which decreases considerable the cost of completions and workovers and aid-in the acquisition of reliable reservoir information at low cost. Completion and remedial operations are performed with tool,; which pass through the well tubing. Perforating and plug-hack operations can be done with the tubing in place and do not require pipe-handling equipment. Because of the many advantages afforded by this method, development work is going forward in anticipation of ultimately being able 10 use it to perform all usual well completion and workover operations. Effort is also being directed to the development of a more permanent type of lift equipment suitable for use with the permanent-type well completion. INTRODUCTION The permanent-type well completion in one in which the tubing and well-head are set in place only once in the life of the well and the completion or remedial work is performed through the tubing with a tubing-type perforator. a retrievable tubing extension. and other wire-line tools. This new type completion has made possible the saving of one to two days' rig time in the completion of each of several hundred wells During the last two years, and use of equipment developed for this type of completion has resulted in a 75 per cent reduction in cost. of certain types of workovers. In addition. the more reliable indication of the commercial value of a reservoir and the more accurate general reservoir information made Possible promise to be of even greater value in oil recovery than the reduction of costs for completions and workovers Recently. several well.. were worked over by using the retrievable tubing extension suspended on a swab line to plug back with cement and then perforating a higher producing interval with the tubing-type perforator, thus opening the way for complete through-the-tubing workovers which may be performed without pipe-handling equipment or mud. Those items attendant to the use of pipe-handling equipment and mud. such as hoard matting rig substructure. and pits. were also eliminated. There are indications that the elimination of drilling mud during completion and workover operations will frequently give increased well productivity, as plugging of the perforation. will not occur. It ii now possible to perforate selectively small sections of the producing interval and to test a well through these sections prior to perforating more interval. The perforating of additional interval will not entail the costly operations of killing the well and pulling tubing, nor will the old or the new perforations be plugged. The productivity of .mall sections of a reservoir and the actual gas-oil or oil-water contacts may now be determined economically under flowing condition.. Selective completions can be made in this manner to delay gas and water problems and bring about maximum oil recovery. At the present time, gas lift appears to offer the greatest potentialities for artificial lift in the permanent-type well com"letion since it can provide full-open tubing to accommodate the through-the-tubing tools and it may be ultimately developed into a fairly permanent type of lift. With precent-day pas-lift equipment. valve or mandrel failure necessitates occacio11al removal of the tubing. thereby reducing to some extent the permanence of the completion. New gas-lift valves are now

Jan 1, 1953

By I. W. Alcorn

The cost of drilling in the past few years of proration and ever decreasing allowables has received increasing thought and study. It seems to parallel the strides made with respect to pumping problems in 1932 and 1933. Low profit margins stimulate the search for economies. Any discussion of slim-hole drilling involves a multitude of abstract values, and the problem can be attacked only by a study of records and rational thinking. In a measure, traditional methods must be studied with a questioning attitude. The words "slim hole" may be somewhat misleading, as the term is entirely relative. For that reason I wish to define it as used in this discussion. On the Gulf Coast, I would define a normal hole as one in which 10 3/4-in. surface casing has been set and below which a 9 7/8-in. hole is dug. With this as a datum, holes of larger diameter below surface would be called "large holes," with 121/4 in. as the "extra large" class and holes of smaller diameter classed in the slim-hole range, 6 1/4 in. representing about the minimum size. The optimum size has not been definitely determined, but the preference is for a program that would call for setting 8 5/8 -in. surface casing and digging a 7 3/4 - in. hole. Different sections of the country might very properly deviate from this practice because of differences in depth, formations, regulations, or other factors. This paper will be confined to a discussion of the drilling of exploratory wells, as the drilling of this class of wells is quite a different problem from that of drilling a proven field, although many of the same considerations apply in both cases, as will be apparent. Although for many years shallow slim-hole and core-test holes of small diameter had been dug, it was not, I believe, until the fall of 1937 that serious consideration was given to its application in drilling wells 7000 ft., 8000 ft. and 9000 ft. deep on the Gulf Coast. This does not mean that nearly all such wells drilled on the Gulf Coast now are of the slim-hole variety, but only that efforts have been aimed in that direction with very encouraging results and there has been a very definite trend to reduce the size of holes, a trend that probably will continue. As to exploration policy, there appear to be two distinct and opposite views. The one usually followed in the past was more or less designed to "shoot the works" on one well. Generally on the Gulf Coast, the depth at which production might be obtained is limited by the drilling equipment and economics. With this thought in mind, wildcat wells are often planned with the idea of carrying the depth to 10,000 It., or even 15,000 ft. All of the possible hazards are anticipated and the general drilling and casing programs are so predicated. Such wells contemplate the drilling of large-diameter holes; the setting of at least one protective string of casing and an extensive coring policy, all of which finally adds up to an expensive well. AS opposed to this general policy is the slim hole. This, on the Gulf Coast, recognizes that new discoveries represent gam-

Jan 1, 1941

By T. R. Ingraham

The thermal decomposition of cupric sulfate and of cupric oxysulfate has been examined by deter-mining the equilibrium gas pressure generated over each pure compound. The equilibrium data have been used to calculate the thermodynamic properties of both compounds, and the results have been combined with previously published data to establish a predominance-volume diagram for the Cu-S-O system over the normal range of roasting temperature and gas composition used in the treatment of copper minerals. Copper oxysulfate recrystal-lizes at 1100°K with an apparently irreversible en-dothermic heat requirement of 2.9 * 0.3 kcal per mole. WHEN mixed sulfide minerals containing copper are roasted, either of two procedures may be followed, depending on the nature of the other metals. In the first procedure, the roasting is controlled to produce a maximum amount of water-soluble copper sulfate which may be removed selectively from the water-insoluble compounds of the other metals. In the second, control is directed toward the production of water-soluble sulfates of the other metals and an insoluble salt of copper. Effective control of either of these processes would be enhanced by knowledge of the thermal stability of cupric sulfate and of cupric oxysulfate. In this paper, established data for the thermal stability of cuprous and cupric sulfide and of cuprous and cupric oxide will be combined with new data for the therma1 stability of cupric sulfate and cupric oxysulfate, to designate the volumes of stability of the significant compounds in the Cu-S-O system in the temperature range 750° to 950°K. EXPERIMENTAL Materials, Apparatus, and Procedure. The copper source material used in all experiments was Fisher Certified Reagent Grade "anhydrous" cupric sulfate, for which the following analysis was supplied by the manufacturer: chloride, 0.002 pct; alkalies and earths, 0.2 pct; insoluble, 0.002 pct; iron, 0.020 pct. Cupric oxysulfate was prepared from the normal sulfate by two procedures. In the first, equimolar quantities of cupric oxide (prepared by decomposition of the sulfate) and cupric sulfate were ground together and heated under vacuum in a sealed silica vessel at 800°C. This procedure was subject to failure because of explosion of the silica vessels due to the pressure of the final traces of water released from the sulfate on the initiation of its decomposition. The second procedure involved roasting the cupric sulfate, with frequent rabbling, in a muffle furnace at 725°C for a period of 48 hr. This produced an excellent product, which was confirmed as copper oxysulfate by X-ray and chemical analyses. The experimental technique used was that of measuring the total pressure exerted by the sulfur trioxide, sulfur dioxide, and oxygen produced by the following reactions: 2 CuS04 = cuo • CuSO4 + SO3 [1] cuo . CuSO4 = 2 cuo + SO3 [2] SO3= SO2 + 1/2 O2 [3] The apparatus used in the experiments has been described previously.1-3 Its main feature of a U-tube mercury manometer in which the mercury is protected from corrosion by enclosure in a flexible Pyrex bellows. Before beginning a run, the interior of the apparatus, including the bellows-manometer and all connecting tubing, was thoroughly washed with hydrochloric acid and distilled water to remove any

Jan 1, 1965

By P. E. Baker

The commercial neutron-gamma log measures the intensity of gamma-rays produced by the interaction of neutrons with nuclei in the formation and in the bore hole. This measurement gives information concerning the distribution of neutrons around the neutron source, and in particular gives information on porosity or fluid content. Another type of information is contained in the frequency or energy spectrum of the neutron capture gamma-rays. The capture gamma-rays of each element, in fact of each isotope, have only those energies characteristic of that isotope.'" The neutron capture gamma-ray spectrum, if obtainable, would permit the identification of the elements producing the spectrum. Such information would have considerable value in oilfield exploration work if it could be applied practically in well logging. Experiments have been carried out at the La Habra Laboratory of California Research Cop. to determine the feasibility of a method of well logging in which neutron capture gamma-ray spectra are measured down hole. In these experiments, spectra were obtained for artificial formations under simulated borehole conditions, using actual borehole geometry. This paper will describe the experimental apparatus and methods and will present the spectrum curves for several formations. THEORY Basic Formulas The neutron capture cross section of an element is a measure of its tendency to capture neutrons. The macroscopic cross section, or cross section per cubic centimeter, of a material composed of several elements is the sum of the cross sections of the nuclei making up 1 cc of the material. This is expressed in the equation SB = Sn1s2, ..........(1) where SB is the macroscopic cross section, s, is the cross section of a nucleus of type i, and ni is the number of nuclei of type i/cu cm. If N is the number of neutrons absorbed per second by the composite material, then the number captured by element j is Ni = N nisi/SB = N nisi/Si ni si ......(2) When the nucleus captures a neutron, a new nucleus is formed, which is usually in an excited state and falls to its ground or unexcited state by emitting one or more gamma-ray quanta.* The emission spectrum has been measured for many elements (see Table 1). The intensity of gamma-rays produced by an element is proportional to the number of neutrons captured per unit time by the element, which in turn depends on the capture cross section of that element and the capture cross sections of the other elements present which are competing with the first element for thermal neutrons. In a small sample of material the number of neutrons, N, captured per second is N = ?SB, ..........(3) where $ is the thermal neutron flux and SB is the macro-scopic cross section defined above. The number of neutrons captured by element j is N1 = ?ni si = N ni si/SB . ......(4) The number of gamma-ray quanta of energy, E, pro-duced per unit time by element, j, is I(E)=Nni si/SB P(E) .......(5) where P(E) is the emission probability of element, j, for this gamma-ray energy. Borehole Effects The capture gamma-ray spectra of many elements have been measured accurately in academic and government laboratories. These measurements are made on small samples, and from these measurements the emission spectra of the elements are obtained.

Jan 1, 1958

By Gerald C. Mathis

FERGUS County, Mont., shown in Fig. 1, is known for its once famous gold mines near the old towns of Gilt Edge, Maiden, and Kendall. But at Heath, a small farming community near the foothills of the Snowy Mountains, thousands of tons of gypsum have been mined since 1916. The value of the gold taken from the mines of Fergus County runs into millions of dollars; the value of the products made from the gypsum of the Heath mine is also in the millions. The gypsum mine will continue to produce for many years, while the gold mines are closed today. The Heath gypsum mine was developed by the Northwest Gypsum Co. in 1916. The products of the small mill built by this company were plaster, agricultural gypsum, and raw gypsum for cement manufacturing. The United States Gypsum Co. prospected the adjacent property in 1916 and 1917 by means of two adits and some exploration drill holes. During World War I, the company abandoned operations at Heath, but again became active in this area in 1928 hen it purchased all the property of the Northwest Gypsum Co. A long range program of expansion was begun with the building of a block plant and the purchase of additional land and mineral rights. A modern wall board plant was built in 1936. When the old wooden mill purchased from the Northwest Gypsum Co. burned in 1937, an all-metal calcining plant located at Blue Rapids, Kansas, was dismantled, moved to Heath, and erected on the site of the mill. In August 1951 a new mine was opened 3000 ft north of the mill. Rock is conveyed from the mine to the mill by an 18-in. belt conveyor. The Heath gypsum deposit lies at the base of the Ellis formation of Jurassic Age. The Ellis at Heath lies unconformably on the black fissle shale of the Heath formation of the Big Snowy Group, which is Mississippian in age. The strike of the gypsum bed is N45°E and the dip approximately 3" NW; the regional strike and dip of the area. The gypsum lies in a series of six layers separated from each other by thin seams of shale. The lower layer is composed of' gypsum and shale intermingled and is not of commercial grade. The upper five layers are high in purity, but only the middle four layers are mined on the advance, as the top layer is left for roof support. This top layer is mined on retreating operations at the same time the pillars are robbed. Total thickness of the gypsum layers varies from 12 to 14 ft. Fig. 2 shows the average thickness and arrangement of the layers. Mining Methods The mine was originally developed by driving an adit into the gypsum horizon. The Northwest Gypsum Co. mined in the top four layers, the top layer being split, leaving about 12 in. for roof support. A modified room and pillar method was used: entries were 15 ft wide and rooms varied between 20 and 30 ft and were turned on 90" from the entries. Crosscuts between the rooms left pillars from 10 to 20 ft square. The rock was loaded by hand into 1-ton mine cars and pulled to a central gathering point by mules; from the gathering point, mules or horses were used to pull the string of cars to the mill tipple. This method was continued by the United States Gypsum Co. from 1928 to 1937.

Jan 1, 1954

By Meguru Nagamori

DURING the smelting of the sulfide ores of copper, nickel, and certain other metals, a matte phase is formed. For a better understanding of the physico-chemical properties of mattes, binary systems such as Cu-S, Ni-S, Fe-S, and so forth, should be studied, especially in the vicinity of liquid compounds such as Cu2S, Ni3S2, FeS, and so forth. These compounds are relatively stable in the solid state although they can exhibit appreciable deviations from stoichiometry. With small deviations from stoichiometry there are large changes in the activity of both sulfur and metal this is a characteristic of both solid and liquid sul-fides near the stoichiometric compositions. In the vicinityof molten Cu2S,1 for instance, the activity of sulfur increases about 100 times for a 0.012 increase in the mole fraction of sulfur and, correspondingly, the activity of copper decreases greatly. In this sens the minor deviations from stoichiometry should be carefully taken into account in studies of such metal-sulfur melts. Metal-sulfur melts may be considered to have properties intermediate between metallic solutions and molten salts, i.e., neither entirely metallic nor entirely ionic. The radius of the ion sZ- is 1.84 as compared with 1.04? for a single bond covalent s.2 It is therefore inferred that when the sulfur is more ionic its partial molar volume is larger, although metal-metal, metal-sulfur, and sulfur-sulfur interactions may bring about further complexities. Thus, it is to be expected that the molar volumes, which are derived from density-composition relations, will help in resolving the structure of the melts. In this study the maximum bubble pressure method with bubbling gases of H2, H2S, and Ar, .was employed to measure the density. EXPERIMENTAL Materials. Silver of 99.95 pct purity was melted in an alumina crucible and hydrogen gas was then bubbled through the liquid for the deoxidation. In preparation of Cu2S, electrolytic copper powder (>99.9 pct Cu) was mixed with precipitated sulfur and heated to 1200°C in an alumina crucible under a hydrogen atmosphere. Mixtures having the approximate compositions FeS and Ni3S2 were prepared by heating reagent grade electrolytic iron or reduced nickel powder with precipitated sulfur under a hydrogen atmosphere. The H2S gas was of 98.5 pct purity, the impurities being mostly CO2 and CS2 which hardly contaminate the melts. Apparatus. The crucible system is shown schematically in Fig. 1. To minimize the variation of melt composition during a density measurement, the apparatus was designed in such a way that either Ar, H2, H2S, or mixtures of these gases could be used as the bubbling gas. When the melt had a high partial pressure of sulfur, H2S gas was used. When the partial pressure of sulfur was so low that oxygen might dissolve in the melt, the use of H2 was preferred. In intermediate cases, argon or mixtures of H2-H2S were used. Density of Dibutylphtalate. Dibutylphtalate was used as the manometer fluid. Relative to distilled water, the density of the dibutylphtalate, pdib g per cc, was measured and found to be: pdib (25°C) = 1.046 i 0.002. With the use of the temperature coefficient reported by Kemppinen and Gokcen,3 the following value was

Jan 1, 1970