Search Documents

By T. P. Meloy

The behavior of slime-sized particles in a flotation cell is neither well documented nor well understood. In general, slimes (or 'fines' as they will be alternatively called in this chapter) have been either ignored, eliminated, or treated empirically. Recently, however, some good experimental and theoretical work has been done that leads qualitatively to a clearer understanding of the problems involved. Fines are small particles that, owing to their smallness, behave differently from larger particles of the same material. The smaller the particle, the larger is its surface-to-mass ratio. The difference in the surface-to-mass ratio for a micron-sized particle and a centimeter-sized particle is 10,000 to 1. For our purposes we shall arbitrarily define any particle less than 10 µ 10-3 cm) as being a fine. This is generally considered the upper limit of colloidal-sized particles. Recently, the field of colloidal chemistry has successfully used the concept of the double layer to explain dispersion and flocculation of fine particles in a static system. Flotation, however, is a dynamic system due both to the turbulence of the liquid and to the coursing of the bubbles through the cell. Further more, a flotation system is a heterogeneous system in which there are a number of different types of particles which interact with one another. A further difficulty is that no two flotation systems are the same for minute quantities of a variety of common chemicals will alter the behavior of the system. These reasons make reproducible experimental results that can ex- plain fine-particle behavior difficult to obtain. In spite of these experimental difficulties, millions of tons of ore containing a large amount of fines are successfully floated every year. For example, at the Morning mill of American Smelting and Refining Co., a galena concentrate that was 42% -6 µ and a sphalerite concentrate that was 33% -9 µ were floated leaving a tailing that was 27% - 9 µ.l Ores that contain fines can generally be divided into two classes. In the first are those in which the valuable mineral tends to slime, such as galena and hematite. In the other class, one or more of the gangue minerals forms the slime; a typical example is barite. Though the problems due to the presence of fines are often the same in handling the two classes of ore, the method of handling them is different because of economic considerations. Nonmetallic mineral flotation is particularly affected by slimes, by either slime-coating effects or excessive reagent consumption. Though a given gangue mineral may not float under the conditions prevailing in the flotation cell, it may still be able to adsorb the collector. I£ it also slimes, a significant

Jan 1, 1962

By Richard Hodgson

FMC Corporation, at their mine and soda ash refinery near Green River, Wyoming, currently mines in excess of 3 million tons per year of trona. Upon completion of the current expansion, the mine will be producing in excess of 4.0 million tons per year. The single level mine, approximately 1,500 feet in depth, is currently serviced by five (5) concrete lined circular shafts varying in diameter from 12 ft. to 24 ft. A sixth shaft is complete, but not yet operational and the seventh is currently being sunk. Two of the shafts are equipped with single drum hoists. The original production shaft is equipped with a double drum hoist. The newest production shaft and the main service shaft are both equipped with ground mounted friction hoists. These friction hoists have given excellent service and another will soon be installed as a man and material hoist at No. 7 Shaft. There are a number of advantages that the ground mounted hoist has over a tower mounted hoist. There are also operating problems common to both. FMC's original experience with ground mounted friction hoists began in 1962 with the conversion of a single drum hoist to a friction hoist. The converted hoist was an Ottumwa with a 5 ft. diameter drum and a 4 ft. face. This hoist had been installed at the No. 3 Shaft for some years prior to its conversion to a friction hoist. At the time the conversion of this hoist was made, there were no friction hoists in service in Wyoming. Wyoming mining laws required that all conveyances carrying men be equipped with safety dogs. Since it was desired that wire rope guides be used, safety dogs were impractical. Agreement was reached with the State Mine Inspectors that safety dogs would not be necessary provided that recommended rope safety factors for hoisting men would still be maintained if one hoisting rope was broken. Since-the shaft is approximately 1,500 ft. deep, the recommended safety factor is 6.0 so that this installation has a safety factor in excess of 8.0 for hoisting men when new ropes have been installed. The hoist conversion was engineered by Lake Shore, Incorporated. The friction ring was made in halves and bolted over the original drum face which had been machined to remove the grooves. The ring provided for four 3/4 in. diameter ropes on 8 inch center to center spacing. The pitch diameter of the modified drum was 72 inches. The grove liners are hald in place by hard-wood wedges bolted to the drum. The other modification required by the conversion was an increase in size of bearing caps and the hold-down bolts because of the increased force tending to lift the drum.

Jan 1, 1975

By R. Schumann

THE expression "unit process " comes up with increasing frequency in discussions among metallurgists and mineral engineers, especially among those concerned with training the next generation. The unit process approach characterizes a significant advance along the road from metallurgy as an empirical art to metallurgy as a branch of engineering. The purposes of this paper are to define and list the unit processes in specific terms, to indicate the scientific and engineering principles basic to all the unit processes, and finally to show how these ideas have been applied to a reorganization of instruction in chemical metallurgy. UNIT OPERATIONS AND UNIT PROCESSES Metals are extracted from ores and other raw materials by stepwise procedures. In general, each metallic element is extracted by a different procedure. For many of the metals there is a choice of several flowsheets. However, the procedures all have steps in common. In fact, the many different flowsheets are all made up of a relatively small number of steps which are combined in different groups and sequences. For example, crushing, screening, roasting, sintering, melting, and gaseous reduction are steps which each appear in the flowsheets for extracting the majority of the metals. The individual steps or flowsheet units can be designated as unit operations or unit processes. These terms are well established in the field of chemical engineering, as the American Institute of Chemical Engineers' definition of chemical engineering shows: " Chemical engineering is that branch of engineering concerned with the development and application of manufacturing processes in which chemical or certain physical changes of materials are involved. These processes may usually be resolved into a coordinated series of unit physical operations and unit chemical processes. The work of the chemical engineer is concerned primarily with the design, construction, and operation of equipment and plants in which these unit operations and processes are applied. Chemistry, physics, and mathematics are the underlying sciences of chemical engineering, and economics its guide in practice."1a In this definition, the distinction between unit operations and unit processes is that the unit operations are physical while the unit processes are chemical. Table I gives a list of the principal unit operations and unit processes of chemical engineering, taken from Shreve. lb Table 2 lists the principal unit operations and unit processes used for metal extraction. The division between unit operations and unit processes is similar to the chemical engineers' distinction and also corresponds approximately to the division of labor between mineral dressing and chemical metallurgy which has been customary in the past. Furthermore, it will be noted that in the proposed classification the unit processes primarily involve chemical reactions and/or changes in state of aggregation; the unit operations, primarily do not involve either bulk

Jan 1, 1948

By W. B. Mather

A SURVEY of the technical literature concerned with oil well drilling methods and particularly with rate of penetration by various cutting media on different types of rock provides a mass of conflicting data. This is especially true with respect to, (1) the relative efficiency of diamond, rotary and percussion drilling operations; (2) the costs of the various types of drilling; and (3) the hardness factor of various types of rock and cutting media. The latter is the particular phase of the subject discussed here. The cause of the confusion may be attributed partially to a lack of 'basic knowledge concerning the physical properties of the cutting media and of individual types of rock. It is also due in part to a general lack of uniform standards in the industry for evaluating the hardness versus drillability of rocks while possible errors in interpretation by the authors of the various papers pertaining to the subject may be an additional cause of misunderstanding. The hardness of a mineral is defined by Dana' as "the resistance which a smooth surface offers to abrasion." Webster' states that hardness is "the cohesion of the particles on the surface of a body (as a mineral) as determined by its capacity to scratch another or be itself scratched." Rock hardness, although not usually defined in publications describing rocks, is assumed to be the same as the minerals which compose the rock or the resistance of the rock to abrasion. Drillability of a rock may be defined arbitrarily as the rate at which rock is penetrated by a definite type of drilling tool with the assistance of a specific type of cutting surface or medium and under speci- fied conditions as to speed of rotation and applications of pressure. Eventually the term penetrability may have to be employed to include any method of making boreholes in rocks, since methods other than those using conventional cutting surfaces are already in operation. A case in point is the jet piercing methoda which employs an oxy-acetylene flame as a means of penetration. The word hardness as used by the drilling fraternity has a variety of meanings which depend upon the type of drilling method employed. For example, in diamond drilling, hardness is interpretated as resistance to abrasion. In percussion drilling the term implies resistance to impact or indentation, while in rotary drilling, hardness is considered anal-agous to compressive strength. The three types of hardness—abrasion, impact and compression—are conflicting variables for different types of rock. Nevertheless, the term hardness is applied indiscriminately by the industry for the resistance of rock to penetration by any type of drilling technique. Abrasion Hardness Since 1818, Moh's scale of hardness, although only relative in nature, has been accepted universally as the method of measuring mineral and therefore rock hardness. In 1933, Ridgway, Ballard and

Jan 1, 1952

By Joseph E. Worthington

Many thousands of years ago when our earliest ancestor first swung out of a tree, picked up a rock, and threw it at what he hoped might be his lunch, the minerals industry, in a manner of speaking, was born. It was then a very long step indeed to the primitive metal industry of our early civilizations, for we know that precious metals were accumulated and some metal objects were produced several thousand years ago. Prospecting, or "exploration" to use the modern euphemism, consisted of little more than outcrop examination and the use of a gold pan, and it probably did not change much from our earliest civilizations until relatively recent times. In a general sense, all the early explorers of North America were also prospectors, for mineral wealth was certainly one of the goals of the first pioneers and settlers. The earliest pioneers didn't do too badly either, for they discovered copper and iron in various places in the Appalachians and Michigan, gold in the Southeast Piedmont and many mineralized areas in the Southwest. In most places these were outcropping ores or gossans, and the prospecting was incidental to the arduous task of ekeing out a living in a new land. It was the explosive discovery of rich placer gold deposits at Sutter's Mill in California that caught the public fancy and precipitated the establishment of prospecting as a full-time occupation. After the end of the Civil War in 1865, full-time prospecting became an important occupation and continued as such for almost three generations. Prospectors equipped with picks, shovels, gold pans and four-footed transportation swarmed all over what are now our Western States, discovering thousands upon thousands of mineral showings-and certainly most of today's large mining districts. Our vigorous western mining industry is a tribute to the courage and persistence of these men. The techniques of these picturesque prospectors, however, were essentially the same as those of their predecessors-examination of every outcrop and assiduous use of the gold pan. The great increase in discovery at this time was therefore due to increased activity rather than to different techniques. An important result of this in- creased prospecting was the growth of interest in geology. It was during this period that the U.S. Geological Survey began to grow. Many of the major mining districts were mapped, and geological studies and projections began to have an impact on further ore discovery. Ore search and development gradually became more geologically oriented and the geologist became a fixture in most mining camps by the 20th century. The development of mass-mining techniques in the early part of the century also changed exploration concepts.

Jan 1, 1971

By L. B. Ticknor, M. B. Bever

An isothermal calorimeter suitable for measurements of heats of solution in liquid tin as solvent is described. Measurements of the heats of solution of gold, silver, copper, and a gold-silver alloy are reported. The heat of formation of this gold-silver alloy is also reported. HEATS of solution in liquids can be determined directly, but few such data have been published for metals as solvents. Knowledge of heats of solution is desirable because it contributes to the general understanding of energy relations in metallic solutions. Thermochemical measurements of this type also furnish answers to specific problems: For example, from the heats of solution of an alloy and of a mixture of its constituent elements in a given solvent, the heat of formation of the alloy may be found. Similarly, differences in the energy content of samples of the same metal in two different states, such as the annealed and cold worked states, may be determined. In the work reported here, gold, silver, and an alloy of gold and silver were dissolved in liquid tin at 240°C and gold, silver, and copper were dissolved in tin at 300 °C. The experiments yielded the heats of solution of these metals in tin. The heat of formation of the gold-silver alloy was also determined. The same calorimetric method is being used to measure the energy stored in metals during cold working and preliminary results have been published.' Equipment and Experimental Procedure The isothermal calorimeter used in this work, Fig. 1, consisted of a Dewar flask completely immersed in a constant-temperature salt bath. A long neck provided space for thermocouple leads and a stirrer shaft and permitted the injection of solute samples. The metal bath in the calorimeter flask was stirred at about 100 rpm by a small glass impeller driven by a constant-speed motor. The shaft of the stirrer passed through a Wilson vacuum seal.2 All measurements were made under vacuum in order to eliminate temperature disturbances resulting from gas convection and to prevent the oxidation of tin. The calorimeter flask was joined by an all-glass connecting line to a gas-control system which made possible the use of a protective atmosphere of deoxidized and dried hydrogen. At the operating temperature of the calorimeter tin oxide was not reduced by hydrogen, presumably because the reaction rate was too slow. Part of the closed system was a removable side tube through which the solute sample could be introduced and in which it was held at a temperature of 0°C prior to injection into the metal bath. The salt bath containing a mixture of sodium, lithium, and potassium nitrates was similar to that described by Beattie3 and was equipped with a stir-

Jan 1, 1953

By Jules E. Jenkins

IN the past quarter century the seismograph has played an increasingly important role in evaluating vibratory effects transmitted to adjacent communities by industrial blasting operations. In this period research has advanced through two major phases—from falling pin seismometers to three-component recording seismographs. The initial phase of this research is now regarded as the era of recording, during which the seismograph merely recorded occasional events. It has emerged from this stage into the era of control and analysis and in this later period has been recognized as a full-fledged industrial tool. Although the falling pin machines of earlier years indicated probable amplitudes of industrial blasting vibrations, they gave no reliable measure of such displacements, nor did they provide essential information concerning direction or frequency of motion. The first contribution of the three-component recording seismograph was the weight-for-distance formula developed by the U. S. Bureau of Mines. This empirical formula enabled users of commercial explosives to determine beforehand the probable vibratory effects of a blast when the weight of the explosives charge and the distance from the shot point were known. This formula has withstood the test of time and is still applicable for blasts detonated by instantaneous methods. The second major contribution of the three-component recording seismograph followed the introduction in 1945 of short period or millisecond delay detonation. This might be described as a two-stage contribution, the first of which revealed a 50 pct reduction in the vibration magnitude when millisecond detonation was used rather than instantaneous discharge. This second part of this double contribution led to the discovery of the vibration dip phenomena, see Fig. 1. In Fig. 1 the horizontal coordinates indicate the displacements amplitude in inches, and the vertical coordinates, the explosive weight in pounds. The top curve is that of the U. S. Bureau of Mines for instantaneous detonation. Its curvature conforms to the two-thirds power of the explosive weight as provided in the weight-for-distance formula; hence the vibratory effects increase in proportion to an increase in the explosive charge. If the other curves shown below are temporarily disregarded, it may be considered that the entire area below this top curve represents both useful and waste energy. As mentioned previously, when millisecond delay detonation was first investigated it was found that in general the U. S. Bureau of Mines curve could be decreased by about 50 pct, or to the position of the middle curve. At the outset it was assumed that this curve would likewise increase in some proportion to the explosive charge, as did the top curve, that is, the curve would indicate a continuous upswing. As seismographic data accumulated this assumption was found to be erroneous in part. It was discovered that

Jan 1, 1957

By Walter W. Bradley

(Three, papers included, in this discussion are classified as Mining Geology and also as one of the following-A, Metal Mining: B, Milling and Concentration: L, Geophysics. These papers are TP 2255, TP 2092 and TP 2038.) CONTENTS [PAGE Review of Fluorescence as Applied to Minerals, with Special Reference to Scheelite. (TP 1967 by J. W. VANDERWILT, Min. Tech., March 1946. Discussion by WALTER W. BRADLEY) I Geologic Interpretation of Magnetic Exploration on the Mesabi Range, Minnesota. (TP 2038 by R. B. H. JONES, Min. Tech., July 1946. Discussion by ROBERT B. SOSMAN) I A Technique for Photographing Difficult Subjects through a Petrographic Microscope. (TP 2092 by DONALD W. SCOTT, Min. Tech., Nov. 1946. Discussion by HORACE WINCHELL) 2 The Search for Concealed Deposits-a Reorientation of Philosophy. (TP 2146 by SAMUEL G. LASKY, Min. Tech., May 1947. Discussion by T. M. BRODERICK)3 Occurrence of Lead-zinc Ore at Iron King Mine, Prescott, Arizona. (TP 21 go by H. F. MILLS, Min. Tech., July 1947. Discussion by HUGH M. ROBERTS)3 Geologic Relations and New Ore Bodies of the Republic District, Washington. (TP 2197 by LAWRENCE B. WRIGHT, Min. Tech., July 1947. Discussion by AUGUSTUS LOCKE and J. A. RICHARDSON) 4 San Manuel Prospect. (TP 2255 by H. J. STEELE and G. R. RUBLY, Min. Tech., Sept. 1947. Discussion by L. KENNETH WILSON, ELDRED D. WILSON and the author) 5] Review of Fluorescence as Applied to Minerals, with Special Reference to Scheelite WALTER W. BRADLEY*-AS I recall, the first portable units for ultra-violet light of practical use with scheelite were developed at the Nevada-Massachusetts Tungsten Mine at Mill City, Nevada, and were used underground. Ultra-violet lamps are also installed there in the mill, above the gravity-concentration tables, for control observations. Geologic Interpretation of Magnetic Exploration on the Mesabi Range, Minnesota ROBERT B. SOSMAN*-When artificial precipitated magnetite is oxidized at a temperature in the vicinity of 100°C, the oxide is converted into a chocolate brown ferric oxide of the formula Fe2O3, free from ferrous iron, yet possessing the same magnetic susceptibility as the original Fe3O4. This form of Fe2O3 is variously called "ferromagnetic ferric oxide," " maghemite," or "gamma ferric oxide," and has been found as a natural mineral. If a body of magnetite in the Biwabik were to oxidize to this form, the oxidized and leached ore body might successfully conceal itself from Mr. Jones' survey by this ferromagnetic pretense. So far, gamma ferric oxide has not been found on the Minnesota iron ranges. I thought I had found some in the Hibbing pit in 1940, in a strongly magnetic specimen of soft ore differing in color from the prevailing hematite

Jan 1, 1947

By R. Schuhmann

The expression "unit process " comes up with increasing frequency in discussions among metallurgists and mineral engineers, especially among those concerned with training the next generation. The unit process approach characterizes a significant advance along the road from metallurgy as an empirical art to metallurgy as a branch of engineering. The purposes of this paper are to define and list the unit processes in specific terms, to indicate the scientific and engineering principles basic to all the unit processes, and finally to show how these ideas have been applied to a reorganization of instruction in chemical metallurgy. Unit Operations and Unit Processes Metals are extracted from ores and other raw materials by stepwise procedures. In general, each metallic element is extracted by a different procedure. For many of the metals there is a choice of several flowsheets. However, the procedures all have steps in common. In fact, the many different flowsheets are all made up of a relatively small number of steps which are combined in different groups and sequences. For example, crushing, screening, roasting, sintering, melting, and gaseous reduction are steps which each appear in the Bowsheets for extracting the majority of the metals. The individual steps or flowsheet units can be designated as unit operations or unit processes. These terms are well established in the field of chemical engineering, as the American Institute of Chemical Engineers' definition of chemical engineering shows: " Chemical engineering is that branch of engineering concerned with the development and application of manufacturing processes in which chemical or certain physical changes of materials are involved. These processes may usually be resolved into a coordinated series of unit physical operations and unit chemical processes. The work of the chemical engineer is concerned primarily with the design, construction, and operation of equipment and plants in which these unit operations and processes are applied. Chemistry, physics, and mathematics are the underlying sciences of chemical engineering, and economics its guide in practice."'1a In this definition, the distinction between unit operations and unit processes is that the unit operations are physical while the unit processes are chemical. Table I gives a list of the principal unit operations and unit processes of chemical engineering, taken from Shreve.1b Table 2 lists the principal unit operations and unit processes used for metal extraction. The division between unit operations and unit processes is similar to the chemical engineers' distinction and also correspollds approximately to the division of labor bctween mineral dressing and chemical metallurgy which has been customary in the past. Furthermore, it will be noted that in the proposed classification the unit processes primarily involve chemical reactions and/or changes in state of aggregation; the unit operations primarily do not involve either bulk

Jan 1, 1949

By Tell Ertl, Ernest E. Burgh

The Bureau of Mines is operating an oil-shale mine 10 miles west of Rifle, Colo., as part of its Synthetic Liquid Fuels program. The purpose of operating this mine is twofold: First, to supply oil shale to an experimental Processing plant; and second, to develop practices and select methods for mining oil shale on a commercial scale at the lowest practicable cost. The second purpose—that of finding out how to mine oil shale most cheaply—entails considerable mining research. Since the drilling of oil shale probably will be one of the major items of the mining cost, fattors that influence drilling speeds were investigated. One phase of the drilling program was the development of a successful hard-surfaced rock-drill bit1 that can be used for drilling long holes in oil shale without changing bits. During that phase, drilling speeds were measured and drill cuttings were collected for assay and for screen sizing, when the cuttings from the individual tests were compared, a definite relationship was shown to exist between the drilling speed and the coarseness of the drill cuttings. Procedure Measurement of Drilling Speeds All drilling in the tests was done with a Model UMB-D-99W Gardner-Denver wagon drill. Round-lugged drill steel, 141 in. in diameter was used in 6, 12, and 18 ft lengths with 1/8-in. Timken H-type bits hard-faced with acetylene tube borium. The tests were made in the lower adit of the Bureau of Mines oil-shale mine; the grade of the oil shale drilled ranged from 18.6 to 42.7 gal per ton, During the experiments air pressure varied between 75 and go psi while water pressure remained fairly constant at 75 psi. All holes were drilled almost horizontally. Each drill hole was thoroughly cleaned of cuttings after being collared. The advance of the drill along the carriage was measured and recorded as the drilling speed in inches per minute. Method of Collecting Cuttings TO facilitate the collection of cuttings, each drill hole was collared in a smooth, vertical portion of the oil-shale breast (Fig 1). A galvanized-stee1 sheet was fastened to the breast below the area in which the hole was to be drilled. The cuttings washed out of the drill hole by the drilling water were guided by the steel sheet into a wooden box. The cuttings that remained in the drill hole after the drill was withdrawn were scraped out and placed in the same box as the cuttings washed out of the hole. After the cuttings from a I-min. drilling interval were collected, they were placed in flat metal pans. The fines were allowed to settle and the clear water was decanted. The cuttings then were dried in the sun.

Jan 1, 1949

By R. L. Huntington, D. T. MacRoberts, Charles R. Hetherington

Since the equation of continuity governing transient flow of gases through porous media cannot be integrated mathematically into a simple usable expression free from series terms, empirical and approximate equations have been advanced relating cumulative production and future production rates from gas reservoirs with time. In order to check the accuracy of these empirical equations and to obtain an insight into the initial conditions pertinent to the solution of the fundamental equation of continuity, experimental work has been conducted on a vertical 2-in. tube, 91.6 ft. high, packed with unconsolidated Wilcox sand. The results presented in graphical form show the accuracy of the approximate relations. Data from unsteady-flow runs on the 2-in. experimental tube are presented graphically, and are applied to obtain an equation for this specific case, and are offered as an aid in future investigations of this basic equation. The close agreement between equations calculated for steady-state flow and the experiments indicates that the decline of actual gas reservoirs may be treated by an application of these equations without serious error. Introduction The steady-state flow of gas through a porous material—that is, flow wherein the boundary conditions do not vary with time—is subject to analytical solution. Muskat1 has shown that the general differential equation is simply the La Place equation in P2. Direct solutions may be at once obtained. The unsteady state, on the other hand, is not analytically reducible. Since nearly all phenomena of practical interest in gas production involve flow in the unsteady rather than in the steady state, it has been necessary to derive approximate Solutions to the general equation. The validity of such approximations has not hitherto been adequately tested. In the experiments to be described a simple, closed, linear system is substituted for the real complex gas field. The general results, however, are independent of the geometry Of the system' The problem studied is the rate of production, and the accompanying variations in pressure, when one end of a linear porous system is opened to the atmosphere and permitted to produce to exhaustion. An approximate solution to the general differential equation, based upon the assumption of an "infinite series of steady states," is then applied to the results to determine the validity of this method of dealing with actual reservoirs. Theoretical Considerations The fundamental differential equation governing the flow of a gas through a Porous medium can be derived easily from the equation of continuity, Darcy's law, Boyle's law and a statement of the thermo-dynamic nature of the flow. For isothermal flow it is: d2P2/dx2 + d2p2/dy2 + d2p2/dz2 = 2fµ/K dP-dT

Jan 1, 1942

By R. Philip Hammond

Monazite has had a Cinderella-like history. Although nearly go per cent pure rare-earth compound (rare-earth phosphate) it was sought at first not for the rare earths but for the sake of a minor constituent—thorium. The thorium, essential for the Welsbach gaslight mantle, was present in only small quantities and the principal constituents, the rare earths, were largely discarded. Gradually, however, the rare earths have developed uses of their own and today have left the thorium far behind in value. Occurrence Monazite was first produced commercially about 1886, in North Carolina, where it was collected in small sluices by farmers who found it in stream beds on their land. The deposits were later exploited on a larger scale, but were mostly abandoned in a few years, when monazite from Brazil came upon the market in far larger quantities. Domestic production ceased entirely in 1906. The Brazilian source is still active, together with Indian, Dutch East Indies, and Australian deposits. Several other localities in the United States have yielded monazite, but none of these has produced commercially as yet. Monazite occurs originally in pegmatite~ and gneisses, through which, unfortunately, it is scattered in highly dispersed form. All commercially useful deposits consist of transported monazite sands liberated by erosion and concentrated by the action of water, which has sluiced away lighter materials and concentrated the heavy (D = 5.0 to 5.2) grains of monazite, together with ilmenite, zircon, garnet, and other dense minerals. The Carolina deposits were in stream beds; most of the other deposits mentioned are on or near the seashore, where the action of the waves has served to concentrate the monazite. In most cases today, the sands are worked to obtain the ilmenite and zircon, as well as monazite. The minerals are separated by means of sluices, dry tables, and magnetic separators, and each is finally obtained nearly pure. No crushing or grinding is necessary. The concentrates are shipped in fiber bags. Composition of Monazite As Table I illustrates, monazite is the anhydrous orthophosphate of the cerium Table i.—Typical Analysis of a Monazite Sand (India). Per Cent Thorium oxide............................. 8.1 Cerium oxide.............................. 30.6 Lanthanum oxide........................... 15. 7 Neodymium oxide.......................... 10.5 Praseodymium oxide........................ 2. 9 Samarium oxide............................ 1.0 Europium. gadolinium, and terbium oxides.... 0.7 Yttrium oxide.............................. 0.4 Dysprosium, holmium, erbium. thulium, ytterbium. and lutecium oxides................. 0. 1 Silicon oxide............t................... 2.4 Calcium, aluminum, and iron oxides.......... 1.0 Uranium oxide............................. 0.3 Phosphorus pentoxide....................... 26. 2 a The values given for the rare earths following samarium are approximate. being based upon analyses of concentrated fractions derived from monazite. The composition given represents Travancore monazite carefully freed from other minerals. goup of rare-earth elements. A small amount of yttrium and terbium group phosphate is also present.* All the rare-

Jan 1, 1948

By L. S. Chabot

INTRODUCTION THE bibliography of mining methods in the past few years has contained many articles dealing with the use of the diamond drill for blasthole drilling. In the Canadian mines, this method has been used with great success in stoping at Noranda, Aldermac, Waite Amulet, East Malartic and Sladen Malartic mines in the Province of Quebec. It has also been used at the Dorchester and Beattie gold mines in Duparquet, Quebec. The method has found useful application at Copper Mountain mine, British Colombia, and at Flin Flon mine in Manitoba. In the United States, the diamond drill blasthole method has been used at Cornwall Iron Ore Mines in Pennsylvania and at the Republic Steel Corporation magnetite properties in the Port Henry district of northern New York. In the Lake Superior iron district, the method has been used at the Anvil-Palms mine of Pickands, Mather and Co. at Bessemer, Mich., and is also used at the Book mine of the North Range Mining Co. at Alpha, Mich. Other companies in the district have also experimented in some degree with the method at some of their properties. This paper is being offered as a preliminary report on the use of the diamond drill method of stoping at the Book mine. Sufficient work has been done with it to prove its worth and it is the purpose of the article to present some results, operational details, equipment ideas and recommendations which we have found in its use at our mine. LOCATION AND DESCRIPTION The Book mine is situated about a mile north of the village of Alpha, in the NE-NE ¼ and the SE-NE ¼ of sec 12-42-33, between the Dunn mine and the Balkan-Judson mine, and about four miles southwest of the village of Crystal Falls, on the Menominee Range of Michigan. The property was found to have ore near surface in sufficient quantities for open-pit operations and stripping was begun in the latter part of 1942 to prepare it for ore production in 1943. During 1943, 288,447 tons of direct shipping ore were produced from the open pit and 382,933 tons in 1944. While the mine was being operated as an open pit some 350,000 tons of lean ore were stockpiled for later treatment. This material is being treated in a washing and jig plant and concentrates are produced during the shipping season. The ore bodies at the Book mine are characteristic of the Menominee Range. They are found on the flanks of sharply folded anticlines which have a fairly steep pitch to the northwest. The open-pit operations in 1943 and 1944 revealed two of these anticlinal structures. A detailed study and classification of the old diamond drill records, coupled with the information of some new holes drilled, has established the

Jan 1, 1947

By B. Paul, C. C. Fu

Experiments indicate that the fatigue limit of various drill steels becomes vanishingly small in the presence of water and other corrosive liquids. Therefore one must generally expect fatigue failures of drill steels in a great many field operations. However, it is theoretically possible to so choose the hammer impact speed of a percussion drill in order to maximize the total length of hole drilled before failure occurs. In this paper the existence of an optimum speed is demonstrated and it is shown to be comparable to presently used piston speeds. The influence on drilling speed and hole length of a number of other pertinent design features, such as bit geometry, hammer geometry and steel properties is also established. Although machinery should be designed to obtain optimum performance, it is not always clear just what performance characteristic is to be optimized. For example in a rock drill it would be desirable to optimize all of the following characteristics: drilling speed, bit life, steel life, total length of hole drilled before failure, and efficiency of energy conversion. The word failure could signify excessive bit wear, bit fracture, steel fracture, or some other type of component failure. It is not possible in general to optimize all performance criteria simultaneously. For example, one could achieve fantastically large drilling rates at the expense of bit or steel life, energy requirements and physical size of system. It therefore becomes necessary to compromise requirements in order to achieve a well-balanced albeit non-optimum design. It is, however, extremely useful to explore the interrelationships between the different performance characteristics. Such a procedure would help to establish theoretical limits of performance within the framework of existing knowledge and also serve as a practical design procedure for special applications where a particular performance characteristic is of greatest concern to the user (e.g., steel breakage might be especially undesirable in certain locations). It is the purpose of this paper to examine the problem of how one may drill the deepest possible hole before breakage of the drill steel occurs. Of course the problem is almost trivial if a well defined fatigue limit (endurance limit) exists for the drill steel. In such cases one merely keeps the piston impact speed sufficiently low to insure that the stresses in the steel never exceed the fatigue limit, thereby achieving an infinite life. If, however, no definite fatigue limit exists, as seems to be the case in the presence of even mildly corrosive agents such as water (see later discussion), then a finite life is inescapable and one can at best hope to maximize the useful life of the system. Indeed it will be shown that the system life is related to drilling speed in the manner shown schematically in Fig. 1-a. Even if a definite fatigue

Jan 1, 1965

By R. W. Brown, J. L. Loper

The process of sand erosion has been harnessed to perform a useful function—the directed perforating of oilfield tubular goods and formation rock. In this process the sand is carried by a liquid medium and the resrrlting slurry is forced through a nozzle at an extren~ely high velocity. Upon impingement against casing or formation, the fast-moving sand particles erode a perforalion in the casing followed by cavity formation in the medium behind the casing. The many factors influencing the rate and extent of this penetration are inherently difficult to establish experimentally. Equations describing submerged jet behavior have been applied to these conditions. The following paper develops the equations for predicting the performance of the perforating jet. INTRODUCTION The cutting power of high-velocity sand has been well known in the petroleum industry for many years. Sand carried by a high-velocity gas stream causes severe erosion. This effect has been the cause of numerous production problems in certain areas. It was logical to expect that this phenomenon would one day be adapted to useful industrial applications. Development of mobile, high-pressure, high-horsepower pumping equipment in the last decade has made this possible. The sand erosion process involves pumping a fluid containing abrasive solids through a set of nozzles at a high differential pressure (2,000 to 4,000 psi). The pressure conversion into kinetic energy imparts high velocity to the sand particles which, upon impact with the formation face or casing wall, erode the material in an organized pattern. This paper attempts to establish the effects of the various parameters and to predict the performance and limitations of the process. The following factors will be considered: nozzle differential pressure, perforation size, sand concentration, nozzle stand-off distance and backpressure. In general, this discussion is presented along theoretical lines and is substantiated by field results and data where reliable field data exists. POWER EQUATIONS The penetration rate of a high-velocity hydraulic jet is proportional to the power or energy of the jet at the point in quesion. The power of the submerged jet will decrease with distance (or penetration) into the cavity created by the jet. As the cavity is extended into the formation, the power of the jet diminishes to a value equal to the threshold cutting power of the particular formation which is defiined as the lowest power level at which the formation will be abraded by the jet. Obviously, when this point is reached, no further cutting of the formation can occur. It is assumed that this power level for a particular formation is a function of the hardness of that formation. The following equation can be written for the hydraulic process of formation abrasion.

By M. J. Saarivirta, P. P. Taubenbla

This paper presents some high-temperature properties of copper-zirconium conductor alloy compared to copper-chromium alloy. Definite superiority of the copper -zirconium alloy over the copper-chromium alloy at high temperatures is shown. RECENT investigations have shown that cold-worked copper-zirconium alloy possesses good room-temperature strength, ductility, and conductivity and maintains most of its strength at temperatures up to 450°C (840°F). As a result, this alloy is now used for many applications, such as commutator segments, resistant welding wheels and tips, rectifier bases, electrical contacts, and so forth. Early investigations1-3 have shown that the maximum solid solubility of zirconium in copper is close to 0.15 pct and the alloy containing Cu-0.10-0.15 pct Zr exhibits the optimum mechanical and physical properties. Results2 have also shown that the alloy has better elevated temperature strength and ductility than copper-chromium and copper-silver alloys. The present investigation was undertaken to learn more about the elevated temperature properties of copper-zirconium alloy and to compare these properties with those of the copper-chromium alloy. WORK PROCEDURE The commercial copper-zirconium alloy, Amzirc was selected for this investigation. Because this alloy is composed of oxygen-free high-conductivity copper and 0.10-0.15 pct Zr, it was believed that possible disturbance from impurities would thus be negligible. Copper-chromium alloys used in this investigation contained 0.40 and 0.70 pct Cr and balance copper. The Cu-0.40 pct Cr alloy was a commercial brand, whereas the Cu-0.70 pct Cr alloy was made from OFHC copper and Cu-5 pct Cr master alloy. It was made in a graphite crucible under argon gas cover and cast. In the preparation of specimens, all three alloys were treated to give the optimum properties; thus the Cu-0.15 pct Zr alloy was solution annealed at different temperatures to determine the desirable solution annealing temperature. It was then cold worked and aged at 375" to 400°C (705" to 750" F). A solution annealing temperature of 1000°C (1830°F) was selected for the copper-chromium alloys because this temperature is widely used in commercial practice. The same alloy was aged at 450°C (840°F) after solution annealing and cold working. It was found that the maximum precipitation hardening of the copper-chromium alloy occurred at this temperature. When aged after solution annealing, the aging temperature was 500°C (930"F) for both alloys. The following properties were determined: 1) Tensile properties as a function of temperature. 2) Effect of solution annealing temperature on high-temperature tensile properties. 3) Stress to rupture strength at 350° and 400°C (660"to750°F). 4) Impact strength. 5) Electrical conductivity and resistivity as function of temperature. 6) Thermal expansion.

Jan 1, 1961

By N. L. Britton

About two years ago Dr. Newberry referred to me for study a considerable collection of fossil plants sent him by Dr. Arthur F. Wendt, engineer of the silver mines " El Cerro Rico de Potosi" in Bolivia. As I had been interested in working up the extensive accumulations of existing plants made by Dr. H. H. Rusby in the Bolivian Andes further north, and in assisting Dr. Rusby in the study of those now being collected by Mr. Miguel Bang in other parts of that country, I was glad of an opportunity of ascertaining something of the Tertiary flora of the region. I was unable to take up the subject at that time, but have since been able to conclude the investigation, and the results are here presented. At a time when the mineral resources of the Southern States are attracting such widespread interest and attention, I have thought it appropriate to give a short general description of the iron-ore deposits of a territory concerning which little is as yet known and nothing published, so far as I am aware. The data used here are due to the preliminary examinations of the North Carolina Geological Survey, on which work I was engaged during the past summer, and my acknowledgments are due to Prof. J. A. Holmes, State Geologist, and Messrs. Harris, Ashe, and Lewis, of the survey, for their co-operation in the work; also to Messrs. A. S. McCreath and C. B. White for analyses which they Kindly furnished. Other analyses were made by Mr. Charles Baskerville, assistant chemist to the survey, and this may be understood where the name of the chemist is not mentioned. All samples for analysis were dried at 212' F. The accompanying map has been prepared from the revised sheets of the United States Geological Survey by Mr. H. L. Harris, and will be referred to throughout this paper. Ashe county lies in the extreme northwestern part of North Carolina, bordering on Tennessee and Virginia; it is drained principally by the north and south forks of New river and their tributaries, and is therefore on the eastern edge of the great Mississippi drainagebasin. The country is exceedingly rugged and mountainous, having an average elevation of about 2900 feet above sea-level. Jefferson, the county seat, near the center of the county, is 45 miles nearly due south from the Norfolk and Western R.R. at Marion, Va., and 30 miles northwest from the Richmond and Danville R.R. at Wilkesboro, N. C. Geologically the ore-deposits described in this paper are situated in the area of the crystalline rocks, consisting chiefly of gneiss, hornblende-schist, and micaceous schists.

Jan 1, 1893

By R. Scot Clark

The reactively sputtered silicon dioxide capacitor -was developed for use in the monolithic integrated circuit, thereby requiring the capacitor to be fabricated on an oxidized silicon slice. The silicon dioxide film is formed by reactively sputtering silicon in a 50 pct Ar-50 pct 0, atmosphere and the physical properties are indistinguishable from silica. A practical upper limit of capacitance per unit area of 0.25 pf per sq mil is reached with the capacitors fabricated from the Si0, film. Methods shown to enhance this value are double stacking the thin-film capacitors and addition of aluminum to the silicon cathode during sputtering to form an aluminosilicate dielectric. A major contribution to the field of diffused integrated circuits would be the addition of auxiliary passive devices for replacement of diffused passive devices which are currently being fabricated for many integrated circuits. This accomplishment would increase the flexibility of the diffusion process in order to concentrate more on transistor parameters rather than on fabricating diffused resistors and capacitors. To pursue this technique, a thin-film SiOz capacitor was developed which has _ proven applicable to many integrated circuits. Although the SiOl capacitor has an application, the major deterrent from extending the integrated circuit into many useful areas such as low-frequency linear application is the low dielectric constant of SiO, and the low usable capacitance in an integrated circuit. This paper will cover the sputtering techniques used for forming the SiO, film, the physical and electrical properties of sputtered SiO,, and yield information concerning the application of these capacitors to integrated circuits. REACTIVE SPUTTERING Reactive sputtering is simply the sputtering of a metal or semiconductor in glow discharge in the presence of a reactive gas. The material to be sputtered is seen in Fig. 1 as the cathode of the system and is bombarded with positively charged ions of the ambient gas. In this investigation, the ambient gas is composed of 50 pct Ar and 50 pct O2 at a pressure of approximately 2.5 X l0-' Torr. The ions are accelerated toward the cathode in the cathode dark space by the electric field and upon striking the cathode effect a momentum energy transfer to the surface atoms. The transferred energy is sufficient to dislodge a surface atom or atoms and these particles diffuse through the glow discharge to the collector or anode. Several mechanisms of oxidation in the reaction chamber can be considered during reactive sputtering. 1) The surface of the cathode is oxidized and the oxide is subsequently sputtered. 2) Oxidation and sputtering occur simultaneously. 3) Sputtering of the cathode material is followed

Jan 1, 1965

By Joseph J. Yancik, Leonard L. Felts, George B. Clark

LITTLE information has been published concerning the actual or useful amount of energy obtained from explosives when they are used for blasting. To provide more data on this subject, 8-in. neet cement cubes were blasted in a steel plate box and the breakage energy evaluated by comparison with drop crusher results using Rittinger's,1,2 Kick's: and Bond's' theories. Theories by Bond and Wang," Lineau," Hatch,' Roller,' and others0-11 were not considered applicable. Those used in this investigation may be expressed mathematically as follows: Rittinger Theory E = KrS2, pet,—--------------- [1] 40 d1 d0 Kick Theory TV 1 1 E = =K, [S pct. log1/d+ 100 log d0] [2] 40 d1 L. L. FELTS, Junior Member AIME, was formerly a Graduate Assistant, University of Illinois. G. B. CLARK, Member AIME, was formerly Professor of Mining Engineering, University of Illinois, and is now Chairman, Dept. of Mining Engineering, Missouri School of Mines and Metallurgy. J. YANCIK, Junior Member AIME, is a Graduate Assistant, Missouri School of Mines and Metallurgy. This paper, TP 4213A. is revised from a thesis submitted by L. L. Felts in partial fulfillment of the M.S. degree in Mining Engineering, University of Illinois, 1954. Discussion may be sent (2 copies) to AIME before May 31, 1956. Manuscript, Dec. 27, 1954. Bond's Third Theory E = Kb [S pct. log1/d1+ 100 log d0] where E — energy used in breakage, d, = average diameters of screen fractions of broken cement particles, pct, = percent weight of diameter d;, and 2 pct, = 100 pct. The above equations were employed to determine values of Kr, Kk, Kb for particle size distributions similar to those obtained from the blasting curves. These values were in turn used as a means of approximating the specific energy of the blasted material. The efficiency of crushing by blasting was then determined by dividing this specific energy by the maximum available work of the explosive per gram of cement. Knowledge of the failure of solids under static loads is developing very rapidly. Their failure under impact loads has been investigated and reported in the literature only to a limited extent. Theories of failure' hnder static loading include 1) the maximum stress theory, 2) the maximum strain theory, 3) the theory of constant elastic strain, 4) theory of maximum shearing stress, and 5) Mohr's theory of strength. All of these have elements of usefulness in establishing an applicable theory for blasting. For highly strained and compressed material such as that surrounding a detonating charge of high explosive, the Mohr theory and its implications appear to be the

Jan 1, 1957

By Frank Foote, E. R. Jette

In recent years the constitution of the high-silver aluminum-silver alloys has been extensively investigated. Hansenl has reviewed the literature to 1935. More recently, Obinata and Hagiya,2 Hofmann and Volk,3 Taziri4 and Tishchenko5 have confirmed the general features of the phase diagram in the region around 25 atomic per cent aluminum. In this paper we present the results of high-precision measurements of lattice constants of the silver-rich alpha solid solution in the homogeneous range and the neighboring two-phase regions. These results are used to establish the nature of the solid solution, the identity of directly measured densities with those calculated from lattice constants and the homogeneity limits of the alpha solid solution with respect to three different neighboring phases. A study of the earlier investigations indicated that the last two subjects in particular required new and accurate data. Experimental Procedure Preparation of the Alloys.—The alloys were made from high-purity silver and aluminum. The silver was "Proof Silver," 99.999 per cent pure, supplied by the U. S. Metals Refining Co. The aluminum was 99.97 per cent pure (contained Si, 0.009 per cent; Fe, 0.0016 per cent; Cu, 0.004 per cent) and was supplied by the Aluminum Company of America. The lattice constants of these two materials have been reported by Jette and Foote.6 Weighed amounts of the two metals were placed in alundum crucibles and melted in vacuo in a high-frequency induction furnace. The melts were allowed to cool in the crucible, the ingots thus obtained weighed about 10 grams. These ingots were then filed clean, hamered, again cleaned and given a homogenizing anneal in vacuo of from 6 to 15 days at temperatures ranging from 500" to 695°C. The ingots were air-cooled from the annealing temperature. Lattice-constant Measurements.—Carefully prepared filings for X-ray analysis were sealed into evacuated quartz or Pyrex tubes and annealed for various periods of time at suitable temperatures. The furnaces used were vertical, rapid-quenching furnaces, the samples being quenched by crushing the sample tube under water by means of a heavy plunger. The general X-ray technique has been previously described6 The cameras were of the symmetrical, back-reflection, focussing type. Ka, radiation from a cobait-nickel alloy target was used. The wave-length values were taken from the second edition of Siegbaum's book.7 A correction for the index of refraction was applied and the lattice constants were calculated by the method of Cohen.8, 6 The lattice constants were calculated to a common temperature of 25°C., using the value of the linear expansion coefficient of pure silver as 18.9 X 10-6. Presumably the expansion coefficient for

Jan 1, 1941