Search Documents

By A. R. Orban, R. B. Engdahl, J. D. Hummell

The initial phase of a research program on smoke abatement from Bessemer converters is described. In work sponsored by the American Iron and Steel Institute, a 300-lb experimental Bessemer converter was assembled to simulate blowing conditions in a commercial vessel. Measurements of smoke and dust were also made in the field on a 30-ton commercial vessel. During normal blows the dust loading from the laboratory converter averaged 0.51 lb per 1000 lb of exhaust gas. This was similar to the exhaust-gas loading of a commercial vessel. The addition of hydrogen to the blast gas of the laboratory converter caused a decided decrease in smoke density. Smoke was also reduced markedly when methane or ammonia was added instead of hydrogen. The research is continuing on a bench-scale investigation of the mechanism of smoke formation in the converter process. DURING the past 2 years, on behalf of the American Iron and Steel Institute, Battelle has been conducting a research program on the control of emissions from pneumatic steelmaking processes. The objective of the research program is to discover a practical method for reducing to an unobjectionable level the emission of smoke and dust from Bessemer converters. PRELIMINARY INVESTIGATION Although conceivably some new collecting technique may be devised which would be economically practicable for cleaning Bessemer gases, no such system based on presently known principles seems feasible because of the extremely large volume of high-temperature gases involved. Hence, the research is being directed toward prevention of smoke formation at the source. A thorough review was first made of former work to determine the present status of the cleaning of converter gases. No published work was found on work done in the United States on collecting smoke or on preventing its formation in the bottom-blown, acid-Bessemer converter. In Europe, however, a number of investigations have been made on the basic-Bessemer converter. Kosmider, Neuhaus, and Kratzenstein1 conducted tests on a 20-ton converter to obtain characteristic data for dust removal and the utilization of waste heat. They concluded that because of the submicron size of the dust, special equipment would be necessary to clean the exhaust gases. Dehne2 conducted a large number of smoke-abatement experiments at Duisburg-Huckingen in a 36-ton Thomas converter discharging into a stack. A number of wet-scrubbing and dry collectors were tried unsuccessfully. A waste-heat boiler and electrostatic collector with necessary gas precleaners was felt to be the best solution for this particular plant. Meldau and Laufhutte3 determined that the particle size was all below 1 µ in the waste gas of a bottom-blown converter. Sel'kin and zadalya4 describe the use of oxygen-water mixtures injected into a molten bath in refining open-hearth steel. They claim that with use of oxygen-water mixtures the amount of dust formed was reduced between 33.3 and 20 pct of its previous level, and emission of brown smoke almost ceased. Pepperhoff and passov5 attempted unsuccessfully to find some correlation between the optical absorption of the smoke, the flame emission, and the composition of the metal in a Thomas converter in order to determine automatically the metallurgical state in the melt. In a recent U. S. Patent (NO. 2,831,762)' issued to two Austrian inventors, Kemmetmuller and Rinesch, the inventors claim a process for treating the exhaust gases from a converter. By their method the inventors claim that the exhaust gases from the converter are cooled immediately after leaving the converter to a degree that oxidation of the metal vapors and metal particles to form Fe2O3 is inhibited in the presence of surplus oxygen. Gledhill, Carnall, and sargent7 report on cleaning the gases from oxygen lancing of pig iron in the ladle. They claim the Pease-Anthony Venturi scrubber removed 99.5 + pct of the smoke, thereby reducing the concentration to 0.1 to 0.2 grain per cu ft, which resulted in a colorless stack gas after the evaporation of water. Fischer and wahlster8 developed a small basic converter and compared the metallurgical behavior of the blow with that of a large converter. Later work by Kosmider, Neuhaus, and Hardt9 on the use of steam for reduction of smoke from an oxygen-enriched converter confirmed that the cooling effect of steam is detrimental to production. From review of all of the published information on the subject, it was concluded that a practical solution to the smoke-elimination problem had not been found. Accordingly, it was deemed desirable to investigate the feasibility of preventing the initial formation of smoke in the converter.

Jan 1, 1961

By C. S. Finney, John Mitchell

The decline of the beehive coking industry was inevitable, but it had filled the needs and economy of its day. A beehive plant required neither large capital investment to construct nor an elaborate and expensive organization to run. The ovens were built near mines from which large quantities of easily-won coking coal of excellent quality could be taken, and handling and preparation costs were thus at a minimum. The beehive process undoubtedly produced fine metallurgical coke, and low yields were considered to be the price that had to be paid for a superior product. Few could have foreseen that the time would come when lack of satisfactory coking coal would force most of the beehive plants in the Connellsville district, for example, to stay idle; and if there were those like Belden who cried out against the enormous waste which was leading to exhaustion of the country's best coking coals, there were many more to whom conservation was almost the negation of what has since become popularly known as the spirit of free enterprise. As for the recovery of such by-products as tar, light oil, and ammonia compounds, throughout much of the beehive era there was little economic incentive to move away from a tried and trusted carbonization method simply to produce materials for which no great market existed anyway. With the twentieth century came changes that were to bring an end to the predominance of beehive coking. Large new steel-producing corporations were formed whose operations were integrated to include not only the making and marketing of iron or steel but also the mining of coal and ore from their own properties, the quarrying of their own limestone and dolomite, and the production of coke at or near their blast furnaces. As the steel industry expanded so did the geographic center of production move westward. By 1893 it had moved from east-central to western Pennsylvania, and by 1923 was located to the north and center of Ohio. This western movement led, of course, to the utilization of the poorer quality coking coals of Illinois, Indiana and Ohio. These coals could not be carbonized to produce an acceptable metallurgical coke in the beehive oven, but could be so treated in the by-product oven. By World War I the technological and economic limitations of the beehive oven as a coke producer were being widely recognized. After the war the number of beehive ovens in existence dropped steadily to a low of 10,816 in 1938, in which year the industry produced only some 800,000 tons of coke out of a total US production of 32.5 million tons. The demands of the second World War led to the rehabilitation of many ovens which had not been used for years, and in 1941, for the first time since 1929, beehive ovens produced more than 10 pet of the country's total coke output. Production fell off again after 1945, but the war in Korea made it necessary once more to utilize all available carbonizing capacity so that by 1951 there were 20,458 ovens with an annual coke capacity of 13.9 million tons in existence. Since that time the iron and steel industry has expanded and modernized its by-product coking facilities, and by the end of 1958 only 64 pet of the 8682 beehive ovens still left were capable of being operated. Because beehive ovens are cheap and easy to build and can be closed down and started up with no great damage to brickwork or refractory, it is likely that they will always have a place, albeit a minor one, in the coking industry. The future role of the beehive oven would seem to be precisely that predicted forty years ago by R. S. McBride of the US Geological Survey. Writing with considerable prescience, McBride declared: "A by-product coke-oven plant requires an elaborate organization and a large investment per unit of coke produced per day. Operators of such plants cannot afford to close them down and start them up with every minor change in market conditions. It is not altogether a question whether beehive coke or by-product coke can be produced at a lower price at any particular time. Often by-product coke will be produced and sold at less than cost simply in order to maintain an organization and give some measure of financial return upon the large investment, which would otherwise

Jan 1, 1961

By S. T. Wlodek

The surface and subscale oxidation reactions were followed by means of continuous weight-gain and metallographic techniques over the range 1600" to 2200°F (871° to 1204 °C) for up to 400 hr. Full identification of all scale and subscale reaction products was obtained by electron and X-ray diffraction. At or below 1800°F (982°C) a linear rate of reaction (QL = 46.0 kcal per mole) governed the oxidation process, extending for up to 100 hr at 1600°F (871 "C). During linear oxidation the surface scale consisted of an amorphous SiO2 film overgrown with Cr 2O 3 and NiCr204. This initial linear process was followed, and above 1800°F completely replaced, by two successive parabolic rate laws (Qp = 60 and 57 kcal per mole). This parabolic reaction involved the formation of a complex scale consisting of Cr2 O3 and smaller amounts of NiCr2O4. Parabolic oxidation appeared to coincide with the disruplion of the silica film present during linear oxidation and was followed by subscale (internal) oxidation of crystobalite and NiCr2O4. The balance between the subscale and surface oxidation reactions controls the oxidation of this commercial alloy. The amorphous silica film appears to result in the linear rate and diffusion through Cr2O3 is the more likely rate-limiting step during parabolic oxidation. THE oxidation of a multicomponent composition is a complex phenomenon not presently amenable to a rigorous classical interpretation. Nevertheless, even a qualitative understanding of the scaling and subscale reactions that occur in a commercial composition can illuminate the reactions that limit its high-temperature stability in an oxidizing environment. This study of the oxidation of Hastelloy Alloy X presents the first of a series of studies with the above approach in mind. Hastelloy X exhibits one of the best combinations of strength and oxidation resistance available in a wrought, solution-strengthened, nickel-base alloy. Although during long time exposure some precipitation of M6C and M23C8 carbides as well as a complex Laves phase occurs, the amounts are probably small enough to have no appreciable effect on the chemistry of the matrix. Radavich has identified the oxidation products on Hastelloy X oxidized for 5 min to 10 hr at 1115°F as NiO and the NiCr2O4 spinel. Oxidation for 5 to 15 min at 1500°F produced a scale of spinel, NiO, and a rhombohedra1 phase, probably Cr2Os. Sannier et 2. have reported continuous weight-gain data for Hastelloy X at 1650" and 2010°F and internal-oxidation measurements after 150 hr at 2010°F. In addition, much of the data on binary Ni-Cr alloys recently reviewed by Kubaschewski and okins' and Ignatov and Shamgunova4 as well as studies of binary Ni-Mo alloys5 are also pertinent to the oxidation of this composition. EXPERIMENTAL Continuous weight-gain measurements and metallographic measurements of subscale reactions were the main experimental techniques used in this study. X-ray and electron diffraction backed up by a limited amount of electron-microprobe analysis served to characterize the nature of the scale- and subscale-reaction products. Two heats of commercial sheet of the composition given in Table I and identified as A and B were used in the bulk of this study. Internal-oxidation measurements were made on a third heat of material in the form of a 0.5-in.-diam bar. In order to assure homogeneity, all heats were reannealed 4 hr at 2175°F prior to sample preparation. weight-Gain Measurement. All specimens (1.5 by 0.4 by 0.03 in.) were abraded through 600 paper, electropolished, and lightly etched in an alcohol-10 pct HCl solution. An electrolyte of 150 cu cm H,O, 500 cu cm HsPO4 (85 pct conc), and 3 g CrO3 at a current density of 0.9 amp per sq cm or a solution of 10 pct HaW4 in alcohol used at 4 v and 0.3 amp per sq cm was used for electropolishing. The resultant surface exhibited a finish of 3 ± 1 p rms. Continuous weight-gain tests were made at 1600°, 1700°, 1800°, 1900°, 2000", and 2200°F on auer' type balances capable of recording a total weight change of 110 mg with an accuracy of k0.1 mg. All tests were made in air dried to a dew point of -70°F and metered into the 2-in.-diam reaction

Jan 1, 1964

By D. S. Choi, R. Stefanko

There are a number of complex factors that influence the effectiveness of anchorage to maintain tension in rock bolts. However, a plastic analysis of the anchorage site employing certain simplifying assumptions with application of the Mohr-Coulomb criterion appears to explain the observed phenomena. Such an analysis has been made and a correlation sought with field and laboratory tests. Field tests were made in an anthracite mine in eastern Pennsylvania and included pull tests and long-term tests of a variety of anchorage devices in two basic lengths, 30 and 42 in. in two widely differing seams. Performance is reviewed for wedge, expansion shell, and resin anchorage. Laboratory tests duplicated many of the field conditions but in addition compared the performance of shells with normal and reversed serrations. This performance was compared with the predicted results from the plastic analysis. One of the major problems in conducting long-term underground tests is the selection of suitable instrumentation. All installed bolts were fitted with spherical and hardened washers to insure the best possible torque wrench readings. In addition, commercially available load cells were used. Finally, the performance of a specially developed strain-gage-equipped ring cell is viewed. Rock bolting as a method of support continues to increase with applications in many other industries in addition to mining. Nevertheless, with nearly 55,000,000 roof bolts installed in coal mines alone last year, this remains as the single greatest use. While bolts have frequently supported ground where conventional timbering could not, there are relatively few design criteria; and trial-and-error procedures prevail. Furthermore, there has been a lag in development of suitable instrumentation that is simple to install and read out, sensitive, durable, reliable, safe, and economical in evaluating the effectiveness of a bolt over long periods of time. Therefore, the pull test continues to be the most popular method of evaluating the applicability of a certain type of roof bolt under specific installation conditions. At The Pennsylvania State University in the Dept. of Mining, research has been conducted for a number of years to measure bleed off in carefully controlled laboratory experiments as well as in underground investigations."-' Unfortunately, most of the instrumentation developed has been primarily suitable only for research purposes, not possessing all of the aforementioned characteristics desirable for routine underground use. Other groups also have met with restricted success. Therefore, while relatively crude, the torque wrench continues to remain as the most widely used load measuring device. While both field and laboratory tests continue to be con- ducted, analytical analyses are attempted to discover the more important design parameters in order that more efficient anchorage might be devised. Bolts are being used for a greater variety of purposes in mining. Suspending wire sideframe belt conveyors from roof bolts is a common application. The suspension of a monorail transportation system presents yet another. One such system has just been installed in a recently reopened anthracite mine and is presently being evaluated under production conditions. Preliminary studies revealed that a considerable cost reduction was possible by suspending the monorail on bolts anchored in the top. The monorail was to be installed under two widely differing conditions—a competent sandstone above the Buck Mountain seam and a softer shale top above the Skidmore. The type of anchorage device, length of bolt, and long-term performance, consistent with economy and safety, had to be established for the installation once the decision was made to suspend the system on rock bolts. This paper describes some of the testing procedures leading to a final selection. Theoretical Analysis of Expansion Shell Anchorage A detailed look at an expansion shell assembly might shed some light on the factors involved in the design of a suitable shell, Fig. 1. When a bolt is rotated, the tapered plug is forced downward, expanding the leaves laterally to grip the sides of the hole. Two friction surfaces are present: (1) the interface of the plug and leaf and (2) the interface between leaf and rock. The relationships of these friction planes, geometry of expansion shell, and properties of the rock are important in the design of an expansion shell. Therefore, an analysis assuming the rock to behave as a rigid plastic material with its yield governed by the Mohr-Coulomb criterion was made." Furthermore, the effect of friction between the leaf and rock produced by serrations was analyzed.

Jan 1, 1971

By M. E. Shank, J. Wulff

At the present time, the designer of dies for metal powder pressing is handicapped by relative ignorance of stress distribution and frictional effects at the interior surface of the die. Unckell was the first to develop a method for the study of wall friction. He used three Brinell balls on which the die rested during pressing. The total frictional wall force was determined by the size of impression these balls left on a soft metal plate. Since the method does not give radial pressures, or distribution of such pressures, coefficients of friction could not be determined. Although Unckel measured density distribution, he was not able to determine radial or shear stresses. Shaler2 has proposed theoretical expressions for the stress and density distribution within cylindrical compacts during pressing, in accordance with the experimental results of Kamm, Steinberg, and Wulff.3 By application of Siebel's method,4 Kamm et a13 plotted stress trajectories for two compacts. From the stress trajectories they calculated coefficients of friction from point to point along the die wall. As pointed out by Shaler in the discussion of Ref. 3, these values are based on progressive point-to-point calculations on finite size grid squares across the compact. In the region of the die wall such calculated values may therefore have considerable cumulative error. The purpose of the present paper is to develop an experimental method by which the nonhydrostatic pressures and shears acting on the interior wall of a cylindrical die can be measured. Such measurements can then he correlated with existing data to aid in the explanation of the pressing process. The method used is based on the elastic: properties of the thick-walled tube used as the die. The principle of super-position of force systems on an elastic body is assumed to hold. Electric strain gauges were mounted in adjacent positions on the exterior die wall in order to get an exact measurement of the variation of tangential strain over the length of the die during pressing. While in this paper, measurements in terms of only tangential strains are considered, it is well to note that similar calculations may be set up for axial strains. The latter are not preferred, since they tend to be smaller than the tangential strains and therefore permit less sensitive measurements. Discussion in this work is restricted to compacts pressed from both ends, since the elastic deformation of the die is then more amenable to analysis. Before choosing the electric strain gauge method, a more direct line of attack was considered and discarded. The discarded idea was the insertion of a pressure gauge through a hole in the die wall.* The gauge would have been in the form of a small piston. If pressure were exerted against such a gauge, it would move outward along a radius of the die. One disadvantage of the scheme is its inability to measure shears along the die wall. Another more serious disadvantage is the disturbance caused by the device itself. It would serve to change the forces it was designed to measure. No matter how small the movement of the gauge, when pressure is applied a discontinuity would exist in the wall surface at that point. Due to the stress concentration caused by the hole, abnormal deflections of the die wall would occur around the gauge. During pressing, powder would be forced into the resulting depression. The depression would then become larger with increasing compacting pressure. Powder, not being a fluid, is capable of supporting shear. The ease with which it would flow into the die wall depression to further move the piston is an indication, not of the radial pressure at that point, but of the state of shear retarding the movement. Thus the "pressure" gauge is really a criterion of flowability, and of the capability of the powder to support shear. For these reasons, it was decided that the electric strain method, herein employed, was more reliable, if more indirect. The gauges and lead wires, mounted on the external die wall do not in any way affect the behavior of the metal powder or the die during pressing. Theory of the Method THE EFFECT OF RADIAL PRESSURE ON THE DIE WALL Effect of a Single Small Band of Hydrostatic Pressure Consider a die which is a thick-walled cylinder of outer radius R. and inner radius Ri. If over a small finite length L there is a normal pressure P, a tangential strain distribution at the outer wall results. This is shown schematically in Fig 1. The exact shape of the curve may he predicted by an extension of the theory of a semi-infinite beam on an elastic foundation.6 This

Jan 1, 1950

By M. H. Yoo

Possible interactions of the perfect dislocations of six slip systems or the c dislocation with the (10i2f (ioii), {ioIi}(ioiZ), {1122}(1123), and {1121}(ii26) type twins in hcp metals have been analyzed from the crystallographic and the energetic points of view. Twenty-six distinct types of possible interactions were identified, and those selected based on crystallographic constraints were examined for their energetic feasibilities by use of the anisotropic energy factors. No long-range elastic interaction exists for a dislocation when its Burgers vector is parallel to the twin interface. Under a suitable applied stress, a screw dislocation can cross slip at the twin interface. For basal mixed dislocations in cadmium and zinc, the interaction with {1012} twins is found to be attractive, indicating that incorporation of these dislocations into the twins is energetically feasible and that twin growth will result. On the other hand, the interaction between both basal and Prism mixed dislocations and the {1012} and (1121) twins is found to be repulsive in Mg, Co, Re, Zr, Ti, Hf, and Be. This indicates that under an applied stress a local stress concentration will develop due to a dislocation pileup at the interface, which may result in a site for either the nucleation of other twins or the formation of a crack, depending on the cleavage strength. WHEN a metal undergoes plastic deformation, a certain configuration of slip dislocations will result in a state of dislocation pileup against an obstacle. The stress concentration thus developed may enhance the process of twin nucleation and also twin growth. Furthermore, once formed and dispersed in the crystal, twins can act as effective barriers against slip dislocations. The degree of such mutual influence or interrelation between slip and twinning is generally known to be pronounced in the case of hcp, metals. It is also known that deformation by twinning occurs more commonly in hexagonal metals than in cubic metals. In fact, under suitable stress states, all hexagonal metals exhibit {1012) <1011> type twinning.&apos; In addition to this common type, deformation by (1151) <1126> type twinning occurs in zirconium, titanium, and rhenium, which show remarkable ductility.&apos; The importance of twinning during general deformation to the ductility of hcp polycrystals has been briefly discussed in recent review works.2&apos;3 The purpose of this paper is to analyze the interaction between slip dislocations and twins in the hcp structure and to discuss the nucleation and growth processes of twinning and the role of twinning in the <"°" noil) o, 1/3[112O] (OOO2) 1/3[1123] Fig. l—-Slip systems in hcp structure. ductility of hexagonal metals. The problem will be discussed from the geometric and the energetic points of view in a manner similar to that of the previous work on zinc.4 Since hcp crystals deform by several slip and twin systems, numerous interactions result as possibilities. The Burgers vectors of six slip systems and the c dislocation shown in Fig. 1 and the four twin systems listed in Table I are considered here. A complete tabulation of the possible interactions is followed by discussion of those that are more likely to occur on the basis of crystallographic constraints and energetic considerations. 1) CRYSTALLOGRAPHY OF TWINNING The crystallographic elements, K1, K2, n1, and n2, for the four compound twin systems are now well established.= A unit cell with the base vectors n1, and n2 is shown in Fig. 2 for each twin system. The unit cell before twinning is shown in solid line, and the corresponding unit cell after twinning is shown in dashed line. Also shown in Fig. 2 are the following crystallographic parameters: S is the plane of shear, d the interspacing of the twin habit planes K1,Ø Iis the acute angle between n1, and n 2, e is a numerical factor, and q is the number of K, lattice planes intersected by 17&apos;. These parameters can be expressed in terms of the axial ratio, y = c/a, as listed in Table 11. The macroscopic shear strain of twinning, s, and the magnitude of a "unit twin dis-l~cation,"4 bt, are also expressed in terms of y and given in Table 11. In Table 11, K1 and q1 are given in both Miller-Bravais and Miller indices. In double lattice structures, shuffling of atoms in addition to a homogeneous shear of the lattice is generally required if the original crystal structure is to be restored after twinning. The extent of current understanding on this problem of atom shuffling is per- Table I. Four Twin Systems in Hcp Structure

Jan 1, 1970

By L. T. Lloyd, H. H. Chiswik

The operative deformation elements in a-uranium single crystals under compression at room temperature have been determined as a function of the compression directions. The deformation mechanisms noted may be arranged with respect to their frequency of occurrence and ease of operation in the following order: 1 — (010)-[I001 slip, 2—{130} twinning, 3—{~172} twinning, and 4bunder special conditions of stress application, kinking, cross-slip, {.-176) twinning, and (011) slip. The composition planes of the (172) and (176) systems were found to be irrational. Cross-slip was shown to be associated with the major (010) slip system, coupled with localized interaction of slip on the (001) planes. The mechanism of kinking was found to be similar to that observed in other metals in that it occurred chiefly when the compression direction was, nearly parallel to the principal slip direction [loo] and was associated with a lattice rotation about an axis contained in the slip plane and normal to the slip direction: the [001] in the uranium lattice. The resolved critical shear stress for slip on the (010)-[100] system was found to be 0.34 kg per mm2 In a single test it was shown that under compression in suitable directions twinning on the (130) also occurs at 600°C. DEFORMATION mechanisms of large grained polycrystalline orthorhombic a-uranium have been studied by Cahn.1 A major slip system identified as the (010) with a probable [loo] slip direction and a minor slip system on the (110) planes were reported; the slip direction of the minor system was not determined. The twinning systems that were identified experimentally included the (130) and the irrational (172) composition planes; observations of other traces which were not as frequent and which did not lend themselves to positive experimental identification led Cahn to postulate on the basis of indirect evidence that twinning also occurred on (112) and (121) planes. In addition to the foregoing slip and twinning mechanisms, Cahn also observed kinking and cross-slip in conjunction with the major (010) system; the cooperative cross-slip plane was not identified. The availability of single crystals to the present authors has enabled them to check these results, particularly with reference to the doubtful mechanisms and the preference of operation of any one mechanism in relation to the direction of stress application. The tests were confined to compression only, primarily because of experimental limitations imposed by the size and shape of the available crystals. The tests were performed at room temperature except for one crystal compressed at 600°C. The compression directions were chosen to obtain a representative coverage of one quadrant of the stereo-graphic projection. To test the existence of some of the deformation elements that were reported by Cahn, but were not found in the present study, several additional crystals were compressed in specifically chosen directions considered most ideal for their operation. Experimental Techniques The single crystals were obtained by the grain coarsening technique described by Fisher? They grinding and polishing on rotating laps, with final surface preparation performed in a H3PO4-HNO3 electropolishing bath. A typical crystal readied for compression is shown in Fig. 1; their dimensions were rather small and depended upon the testing direction. Crystals isolated for compression in a direction close to the [010] axis, which lay roughly parallel to the longitudinal axis of the polycrystalline rod, were about 3 to 4 mm long and 5 mm2 in cross-section, while those prepared for compression in other directions were smaller. Most of the crystals were free from twin markings and showed no evidence of Laue asterism. Several crystals, however, contained twin traces prior to compression; these were identified prior to compression so as to clearly distinguish them from those initiated during deformation. The origin of the twin markings prior to deformation may be ascribed to two sources: thermal stresses and specimen handling during isolation and preparation. Two other types of imperfections in the crystals should be mentioned: inclusions, which were probably oxides or carbides. and three of the crystals contained a small number of spherical included grains (<0.01 mm diam), which were remnants of unabsorbed grains from the coarsening treatment. The volume represented by these imperfections was small, and their presence presented no difficulties in the interpretation of the macrodeformation processes during subsequent compression. Two compression fixtures were employed: crystals A, B, C, E, and G were compressed in a hand-operated screw-driven jig whose compression platens were designed to minimize axial rotation;

Jan 1, 1956

By C. Atkinson

A method is described for the numerical solution of the diffusion equation with a composition-dependent diffusion coefficient and applied to the radial growth of a cylinder; the radial growth of a sphere, and the symmetric growth of an ellipsoid. Sample applications of the method are made to the growth of particles of proeutectoid ferrite into austenite. RECENTLY&apos; we described a method for numerical solution of the diffusion equation with a composition-dependent diffusion coefficient for the case of the growth of a planar interface. In this paper we extend this method to describe the radial growth of a cylinder, the radial growth of a sphere, and the symmetric growth of an ellipsoid. In the latter case, limiting values of the axial ratios of the ellipsoid reduces the problem to one of a cylinder, a sphere, or a plane depending on the axial ratio. A check on these limiting values is made in the results section. In all of these cases we consider growth from zero size. A natural consequence of this assumption as applied to the sphere, for example, is that the radius of the sphere is proportional to the square root of the time. This is consistent with the condition that the radius is zero initially, i.e., grows from zero size. It may be argued that it is more realistic to consider particles which grow from a nucleus of finite initial size; even in this case the analysis of this paper is likely to be applicable. This can be seen if a comparison is made of the work of Cable and Evans,2 who consider a sphere of initially finite size growing by diffusion in a matrix with a constant diffusion coefficient, with the results of Scriven3 for growth from zero size. This comparison shows that the rates of growth in each case differ trivially by the time the particle has grown to about five times its initial size." This investigation is a generalization of those of Zener,4 Ham,5 and Horvay and cahn6 to the situation often encountered experimentally, in which the diffusion coefficient varies with concentration. First let us consider each of the cases separately. I) GROWTH OF SPHERICAL PARTICLES FROM ZERO SIZE In this case the differential equation in the matrix depends only on R, the radius in spherical coordinates, and can be written: ? 1 <^\ ^13D . , dt U\dRz + R 3Rj + dR dR [ J where C is the composition, t is the time, and D is the diffusion coefficient which depends on c. The boundary conditions will be: c = c, at the moving interface in the matrix, c = c, at infinity in the matrix (and at t = 0, everywhere in the matrix), c = X, is the composition in the spherical particle. Each of the above compositions is assumed constant. In addition there is the flu condition at the moving interface which can be written: , dR0 ~/3c dt \dR/H =Ra where R,, which is a function of t, is the position of the moving interface. We make the substitution q = RI~ in [I] reducing this equation to: & - m - *ws) »i where we have written D = D,F(c) or simply D,F, and Do = D(c,). Thus F[c(q0)] = 1 where q, = ~,/a is the value of the dimensionless parameter q evaluated at the interface. Multiplying Eq. [2] by dq/dc and integrating, we find: where the lower limit of the integral has been chosen so that dc/dq — 0 as c — c,, thereby satisfying the boundary condition at infinity. We require, then, to solve Eq. [3] subject to the condition c = c, when q = q, (this follows from putting R = R, at the interface) together with the flux condition which can be rewritten in terms of q as: Eqs. [3] and [4] together with the condition c = c, at q = q0 enable us to find 77, and the concentration profile c = c(q). Numerical Method. We treat Eq. [3] in the same way as we did the corresponding equation for the planar interface problem&apos; i.e., by dividing the interval c, to c, into n equal steps so that: cr = ca -rbc [5] where r takes the values 0, 1, ... n and we call no,, q1, ... nn the values of n corresponding to the compositions c,, c,, ... c,.

Jan 1, 1970

By W. A. Backofen, G. Y. Chin, W. F. Hosford

The ductile fracturing process was studied in single-crystal and poly cvystalline aluminum deformed in tension over a temperature range from 295° to 4.2°K. At temperatures as low as 77°K, the fracture of "inclusion-free" material, including zone-refined aluminum, was by rupture (-100 pct RA). At 4.2 OK, fracture was brought on by adia-batic shear. Metallographic examination did not disclose any voids or slip-band microcracks, thus negating for inherently ductile metals any mechanism of void nucleation by vacancy condensation or of cracking due to dislocation pile-ups. In Izigh-purity aluminum not treated to be inclusion-free, fracture at temperatures as low as 45°K was of the double-cup type and a result of void formation. The reduction-of-area decreased as temperature was lowered, corresponding to the earlier appearance of voids. Such behavior was rationalized in terms of a larger increase, with decreasing temperature, in the .flow stress relative to the strength of the inclusion-matrix interface. Evidence for low-temperature adiabatic shear was found in discontinuous flow at 4.2"K, in the transition to a localized shear fracture at low temperatures, and in the suppression of shear fracture with an elastically hard pulling device. A simple analysis for the initiation of adiabatic shew permitted a general correlation of the various contributing factors. It has been pointed out that the duration of shear depends upon effective mass and elastic stiffness of the deformation system. IT has long been recognized that fracture* may Throughout this paper, the term "fracture" is taken to mean any process that results in the separation of a material into two (or more) parts. Thus rupture as it may be encountered in a tension test leading to 100 pct reduction-of-area is included in this category. occur in a ductile mode, and that the process can be of great practical as well as general interest. Much information about ductile fracture has also been accumulated over this period, but only recently has an understanding of mechanism begun to appear. Ludwik,&apos; in 1926, first reported fracture in a tensile specimen starting with a central crack in the necked section. Since then, other studies have disclosed that such cracks may form by the coalescence of voids nucleated in this region where hydrostatic tension is highest.2-4 Rogers and Crussard et al.&apos; have emphasized void formation and reori-entation along localized shear bands as a mode of crack propagation. pines6 has considered the tensile rod as a bundle of fibers joined by weak interfaces, which subsequently separate to allow individual fiber contraction. The notion of cavity growth and coalescence by purely plastic processes was discussed by Cottrell: who added that the tensile reduction-of-area ought not to be sensitive to temperature. On the other hand, it has been observed that the reduction-of-area is greatly increased if tests are carried out at high temperaturesa or under high hydrostatic pressure.&apos; Fracturing anisotropy in wrought products lends support to the idea of void formation from preexisting flaws strongly aligned by earlier processing.&apos;&apos;-l2 There is evidence that many voids result from the fracturing of inclusions or separation at the inclusion-matrix interface Another possibility is that voids grow out of pore volume produced in the initial solidification and never fully removed in later working. In general, a structure 3f particles, pores, and weak interfaces can be expected, at least in materials of engineering interest. Vacancy condensation has been suggested as an alternative mechanism of void formation for materials considered to be inclusion-free.13 Yet experience has shown that tensile reduction-of-area increases with purity, to the extreme of rupture as so often observed in single crystals. Adiabatic shear has an important bearing on ductile fracture. It occurs when the decrease of flow stress, as a result of local temperature rise from heat generated during straining, becomes larger than the increase due to strain and strain-rate hardening. As demonstrated by experiments on punching of plates,14 a large temperature rise may be brought about by rapid straining. Adiabatic flow as a result of the high strain rate reached in an ordinary tensile specimen just prior to separation may account for the cone formation in cup-and-cone fracture;14 evidence of such local heating has been presented.15 For geometrical reasons, however, pure sliding along the conical surfaces is unlikely, and separation under tensile forces is probably an important accompanying feature of the shear.7 In deformation processing operations, a high shear-strain rate may exist at boundaries between plas-

Jan 1, 1964

By G. R. Belton, R. J. Fruehan

The Knudsen cell-mass spectrometer combimtion has been used to study the Fe-Al and Ag-Al liquid alloys. By application of the recently developed integration technique to the measured ion-current ratios, activities have been derived for the Fe-A1 system at 1600° C and for the Ag-Al system at 1340"C. The results are partially represented by the following equations: Internal consistency between the data on silver-rich and iron-rich alloys is demonstrated by application of the literature measurements on the distribution of aluminum between the nearly immiscible liquids iron and silver. The usual restrictions on the ratio of the mean free path of the escaping atoms to the orifice diameter of the Knudsen cell are shown not to be limiting in this technique. DESPITE the importance of a knowledge of the activity of aluminum in understanding deoxidation equilibria in molten steel, no direct studies have been made of activities in liquid Fe-A1 alloys at steel-making temperatures. Lower-temperature direct studies have, however, been carried out on aluminum-rich liquid alloys by Gross, Levi, Dewing, and Eilson&apos; at 1300°C and by Coskun and Elliott&apos; at 1315°C. Apart from phase diagram calculations by Pehlke, other determinations have been indirect and were made by measurement of the distribution of aluminum between iron and silver475 and combination of these data with extrapolated activities in the Ag-A1 system.~-% ecently, however, Woolley and Elliott have made a significant contribution by directly measuring heats of solution in the Fe-A1 system at 1600°C. The present authorslo have recently employed a Knudsen cell-mass spectrometer technique in a study of activities in iron-based liquid alloys. In this technique activities and heats of solution are determined from a series of measurements of the ratio of ion currents of the components; and since ion-current ratios are used, problems caused by changes in instrument sensitivity or cell geometry are overcome. Results obtained for the Fe-Ni system were found to be in excellent agreement with previous work, thus demonstrating the reliability of the method. The present paper describes a similar study of activities in the liquid Fe-A1 and Ag-A1 systems, this latter system being included in order that a meaningful comparison can be made with the above-mentioned indirect studies. INTEGRATION EQUATIONS A detailed derivation of the equations used to determine the thermodynamic properties from the measured ion current ratios has been given elsewhere;&apos;&apos; however it is useful to summarize them here. By the combination of the Gibbs-Duhem equation with the direct proportionality between ion-current ratios and partial pressure ratios, it was shown that for a binary system at constant temperature and pressure: where al is the activity of component 1 with pure substance as the standard state, N, is the atom fraction of component 2 in the solution, and I; and t&apos;2 are ion currents of given isotopes of the components. The activity coefficient is given by: this latter equation being more suitable for graphical integration. Combination of Eq. [l] with the Gibbs-Helmholtz equation gives an expression for the partial molar heat of mixing: EXPERIMENTAL A Bendix Time-of-Flight mass spectrometer model 12! fitted with a 107 ion source and a M-105-G-6 electron multiplier, was used to analyze the vapor effusing from the Knudsen cell. The arrangement of the Knudsen cell assembly was essentially that of the commercial instrument (Bendix model 1030) but with several modifications. Instead of heating with a single tungsten filament, a cylindrical tantalum-mesh heater was employed. Up to 1400°C simple resistance heating was used but above this temperature electron bombardment between the tantalum mesh and the tantalum cell susceptor was necessary. The temperature was measured by means of a Leeds and Northrup disappear ing-filament type optical pyrometer sighted on an essentially black-body hole in the side of the cell. Details of the temperature control, temperature measurement, and in situ calibration of the optical pyrometer can be found elsewhere.I0 In the investigation of the Fe-A1 system the Knudsen cells were constructed of thoria crucibles with fitted thoria lids (Zircoa). The cells employed in investigating the Ag-A1 alloys were made up of high-purity alumina crucibles (Morganite) with lids of recrystal-lized alumina (Lucalox). The cells were 0.370 in.

Jan 1, 1970

By H. Conrad, V. V. Damiano, G. J. London

The slip mode activated during the c axis compression of single crystals of commercial-purity ingot SR beryllium, high-purity (twelve-zone-pass) beryllium, and Be-4.4 wt pct Cu and Be-5.2 wt pct Ni alloys in the temperature range of 25° to 364°C was determined using two-surface slip trace analysis, slip-step height analysis, and electron transmission microscopy. All three techniques indicated the occurrence of copious pyramidal {1 122) (1123) slip in the alloys over the entire temperature range, the amount increasing with temperature. Pyramidal slip was also indicated in the high-purity beryllium by slip trace analysis and electron transmission microscopy, but the amount was somewhat less than in the alloys. For the commercial-purity ingot crystals, only a very small number of pyramidal slip lines were observed, and these were in the immediate vicinity of the fracture surface. No pyramidal dislocations could be detected by electron transmission microscopy in this material. Dislocatransmissiontions with Burgers vectors [0001] and +(ll20) were identified by electron transmission microscopy inthe (1122) slip bands, as well as those with the j (1123) vector. This was interpreted to indicate that the edge components of the 3(1123) vector dislocations activated during c axis compression dissociate upon unloading according to the reaction i (1123) — [0001] + 3(1120) THE microstrain c axis compression of single crystals of commercial-purity ingot SR beryllium (99.6 pct), high-purity twelve-zone-pass beryllium (99.98 pct), Be-5.24 pct Ni and Be-4.37 pct Cu alloys was described in a previous paper.1 This paper covers in detail the analysis of slip traces observed on two mutually perpendicular lateral surfaces of these specimens, and a detailed description of transmission electron microscopy studies performed on foils cut from the bulk crystals after they had been deformed to fracture in the c axis compression. Observation of slip traces on single surfaces of deformed single crystals are generally insufficient to positively identify slip or twinning modes. The use of two carefully cut and oriented perpendicular surfaces can greatly aid in the positive identification and index- ing of slip traces, although even this technique may be quite inadequate if more than one type of slip system operates and if an insufficient number of traces are observed on the surfaces. The problem is greatly simplified for symmetric cases like that for c axis compression of an hep crystal such as beryllium, in which the operating slip systems are all equally inclined to the direction of the applied stress, and each slip system of a given slip mode has an equal chance of operating. For such cases, the traces of any given slip mode observed on the surfaces cut parallel to the c axis are symmetrically tilted about the c axis. It is therefore possible to quickly determine whether one or more slip modes are operating. Confirmatory evidence in support of the observations made on the external surfaces can be obtained from foils cut from the deformed crystals and examined by transmission electron microscopy. This latter technique serves to identify not only the operating slip plane but also the Burgers vector of the dislocations which participate in the slip. For this purpose, a simplified technique based upon a double tetrahedron notation is used in the present paper. The planes and directions in the hep lattice are all designated by letters rather than indices and extinction conditions are easily determined if the Burgers vector lies in the plane contributing to the diffraction. RESULTS 1) Slip Trace Analysis. The standard (0001) stereo-graphic projection of beryllium is shown in Fig. 1. The two mutually perpendicular, lateral surfaces of the compression specimen are represented by the diametrical planes AA&apos; and BB&apos;, also referred to as surface A and surface B. For the specific case represented (a Be-5.24 pct Ni specimen deformed by c axis compression at room temperature), the A surface is tilted 5 deg to the (10i0&apos;) plane and the B surface is tilted 5 deg to the (1120) plane. Two surface trace analyses may be facilitated by examining in turn the intersection of various great circle traces of specific pyramidal planes with two surfaces and comparing the angles made with the (0001) plane with those actually observed on the two surfaces. One then identifies the slip traces by trial and error on a best-fit basis. The (1122) type planes (it was found that slip occurred on these planes) are shown plotted on the stereographic projection in Fig. 1. One obtains directly the angles between the (0001) plane and the {1122) traces by measuring the angle from the periphery to the point of intersection along the lines

Jan 1, 1969

By J. P. Timmons, J. H. Moran, G. K. Miller, M. A. Coufleau

A prototype equipment has been designed and built for the digital recording of well logs on magnetic tape at the same time that the regular film recording is made. The format of the digital tape produced is such that it can be used directly at the input of the ZBM 704, 7090 or other models of ZBM computers which accept digital magnetic tape. This apparatus has been used for the experimental field recording of dipmeter tape logs which were subsequently computed by means of an ZBM 704 or 7090. In this paper the equipment and the digital tape are described briefly, and their application to the computer-interpretation of dipmeter data is discussed. A principal element in the interpretation of the dipmeter log is the correlation of the three microresirtivity dipmeter curves to determine the depth displacements between them. Several correlation methods for computer use are considered, with particular attention to their sensitivity to error and their consumption of computer time. The tape data were used to compute information content of the dipmeter microresistivity curves in terms of their frequency spectra. The results show that the sampling rate used in recording the digital information is quite adequate and illustrate a use of the digital tape in evaluating the characteristics of new tools. Some examples of field results are shown. It can be foreseen that, when digital tape recording becomes available for general field use, a whole new realm of possibilities will be opened up for the processing of other well logs through computations, which hitherto were not feasible because they were too laborious and time-con.sunzing. INTRODUCTION The last few years have seen a revolution in the design and production of data-processing equipment. Stored-pro-gram digital computers have progressed from a research curiosity to the basis of a major industry. There are now hundreds of such machines in daily use in the United States. With the acceptance of a technique that was, in fact, already clearly described by John von Neumann in 1945, the last decade has seen great strides in the development&apos;of components, reliability, programming systems and, most spectacularly, in the sheer number of machines built and in use. In 1957 there were enough digital computers available to the oil industry to justify the suggestion that it would be worthwhile to investigate the possibility of using these machines in processing well log data.&apos; The first result of this investigation was the appearance of what may be referred to as the input-output bottleneck. Well logs are customarily recorded on film. To get these data into a machine required then (and still does): a time-consuming semi-automatic reading of the film; conversion of the log data to digital form; and recording these digital data in some medium acceptable for computer input, such as cards, magnetic tape, or punched paper tape. However, the recording, reading, and re-recording could only result in deterioration of the data. Therefore, it was concluded that the fist step should be the development of a new, more direct recording technique supplemental to the film recording, which would provide easy access to the digital computer. There are many solutions to the problem of recording log data in an easily recoverable form. After careful consideration it was decided to adopt the boldest solution which, it was felt, was also the most elegant. It was decided to record well logs directly, in the field, on magnetic tape in such a way that this tape could be used without further modification as an input to the IBM 704 or 7090 computer. To realize practical field recording of magnetic tape logs, it became necessary to develop in a rather small package, an analog-to-digital converter, a tape recorder, and the necessary multiplexing and control circuits to allow the simultaneous recording of a multiplicity of logging signals. The magnetic tape recording was to be made simultaneously with the conventional logging operation in such a way as not to interfere with it. Along with the development of hardware, it was necessary to begin development of interpretation techniques and machine programs that would exploit the power of the digital computer. Here, again, there is a long list of possible applications. After much consideration it was decided to concentrate on the interpretation of the dipmeter log as a first application. It is the object of this paper to describe in some detail the developments sketched in the last three paragraphs.

By N. A. Gokcen, John Chipman

SILICON is the most commonly used deoxidizer and an important alloying element in steelmak-ing; hence a detailed study of this element in liquid iron containing oxygen is of considerable interest. The equilibrium between silicon and oxygen in liquid iron has been studied by a number of investigators but generally with inconclusive or incomplete results. The variation of the activity coefficients of silicon and oxygen with composition is entirely unknown. Published investigations deal with the reaction of dissolved oxygen with silicon in liquid iron and the results are expressed in terms of a deoxidation product. For consistency and convenience in comparison of the published information, the deoxidation product as referred to the following reaction is expressed in terms of the percentage by weight of silicon and oxygen in the melt in equilibrium with solid silica: SiO (s) = Si + 2 O; K&apos;l = [% Si] [% 012 [I] Theoretical attempts to calculate the deoxidation constant for silicon in liquid iron from the free energies of various reactions yielded results which were invariably lower than the experimental values. Thus, the deoxidation "constants" calculated by McCance,1,2 Feild,3 Schenck, and Chipman were of the order of 10, which is below the experimental values by a factor of more than 10. Experiments of Herty and coworkers" in the laboratory and steel plant resulted in an average deoxidation constant of 0.82x10 &apos; at about 1600°C. The technique employed in their investigation was crude and the reported temperature was quite uncertain. The concentration of silicon was obtained by subtracting silicon in the inclusions from the total. Since at least some of the inclusions resulting from chilling must represent a fraction of the silicon in solution at high temperatures, such a subtraction is not justifiable. Results of Schenck4 for K&apos;1 from acid open-hearth plant data yielded a value of 2.8x10-5, which was later revised as 1.24x10 at 1600°C. Similarly Schenck and Bruggemann7 obtained 1.76x10-5 at 1600OC. The discrepancies and errors involved in the acid open-hearth plant data as compared with the results of more reliable laboratory techniques were attributed by these authors to the lack of equilibrium and the impurities in liquid metal and slag, and are sufficiently discussed elsewhere." Korber and Oelsen" investigated the relation between dissolved oxygen and silicon in liquid iron covered with silica-saturated slags containing varying concentrations of MnO and FeO. The deoxidation products obtained by their method scatter considerably, and their chosen average values of 1.34x10, 3.6x10-5, and 10.6x10-5 1550°, 1600°, and 1650°C, respectively, represent the best experimental results which were available until quite recently. Darken&apos;s10 plant data from a steel bath agree approximately with their data at 1575° to 1625°C. Zapffe and Sims" investigated the reaction of H2O and H2 with liquid iron containing less than 1 pct Si and obtained deoxidation products varying by a factor of more than 20. Inadequate gas-metal contact and lack of stirring in the metal bath should require a longer period of time than the 1 to 5.5 hr which they allowed for the attainment of equilibrium. Furthermore, their oxygen analyses were incomplete and irregular and confined to a few unsatisfactory preliminary samples. Their results did indeed indicate that the activity coefficient of oxygen is decreased by the presence of silicon, although they made no such simple statement. They chose to attempt to account for their anomalous data by the unlikely hypothesis that SiO is dissolved in the melt. Hilty and Crafts" investigated the reaction of liquid iron with acid slags under an atmosphere of argon, making careful determinations of silicon and oxygen contents at several temperatures. Despite erroneous interpretation of the data at very low silicon concentrations, their data represent the most dependable information on this equilibrium that has been published. In the range 0.1 to 1.0 pct Si, their data yield the following values for the deoxidation product: 1.6x10-5, 3.0x10- &apos;, and 5.3x10 at 1550°, 1600°, and 1650°C, respectively. The purpose of the work described herein was to study the equilibrium represented by eq 1 as well as the following reactions, all in the presence of solid silica: SiO2 (s) + 2H2 (g) = Si + 2H2O (g);

Jan 1, 1953

By R. W. Bartlett

The rates of oxidation of tungsten have been determined at temperatures between 1320" and 3170°C and oxygen pressures to 1 amn using a surface -recession measurement technique. Above approximately 2000°C and 10-6 atm the rate is independent of temperature and can be calculated from gas collision theory assuming a constant reaction probability, e, of 0.06. Oxygen molecules react at surface sites where oxygen atoms have previously chemisorbed. This provides a direct pressure dependence at low pressures but at high pressures tungsten oxide molecule s form an adjacent gas boundary layer which lowers the PO2 at the tungsten surface. A correction for this effect using free-convection theory fits the rate data over the entire oxygen-pressure range from 10-8 to 1 atrn as well as data using O2-A mixtures. Below 10-6 atrn and above 2000°C, e decreases with increasing temperature because of desorption of oxygen atoms. Below 2000°C the rate decreases with decreasing temperature at all oxygen pressures following an apparent activation energy of 42 kcal per mole and depending on (Po2)n with n varying between 0.55 and 0.80. MOST of the previous tungsten oxidation studies have employed gravimetric methods and have been limited to temperatures below 1000°C where the weight loss associated with evaporation of tungsten oxides is negligible compared with the weight gain from oxidation.&apos; At higher temperatures, oxygen-consumption rates have been determined from pressure measurements, usually at constant flow rates, by Langmuir,2 Eisinger,3 Becker, Becker, and Brandes,4 and Anderson.5 The sensitivity of this method decreases with increasing pressure and, with the exception of Langmuir&apos;s work, these investigations were confined to pressures below 10-6 atm. Above approximately 1300°C, depending on the oxygen pressure, the rate of oxide evaporation is greater than the oxide-formation rate and the recession of the tungsten surface can be measured optically without interference from an oxide layer. This was first done by Perkins and crooks6 who heated tungsten rods in air pressures from 1 to 40 torr at temperatures between 1300" and 3000°C. The present investigation of the oxidation kinetics of tungsten at high temperatures emphasizes oxygen pressures from 10-6 to 1 atm. This is the range of interest for earth atmosphere re-entry applications of tungsten for which little data were previously available. APPARATUS The apparatus is a modification of the type used by Perkins and crooks.&apos; Ground tungsten seal rods, 6 in. long by 0.125 in. diam, were mounted vertically between two water-cooled electrodes, one fixed and the other having free vertical travel. The movable counter-weighted electrode is prevented from undergoing horizontal displacement by three sets of runners mounted at 120-deg intervals. Electrical contact is made by means of a water-cooled mercury pool. A 24-in. vacuum bell jar having a volume of approximately 267 liters was used as the reaction chamber with the sample holder mounted in the middle of the chamber. Power was supplied from an 800-amp dc variable power supply. Temperature readings were made by means of a Latronics automatic two-color recording pyrometer. With this instrument, corrections for emissivity are not necessary provided the spectral emissivi-ties at two closely spaced wavelengths are equal. Supporting measurements were made with a micro-optical pyrometer corrected for emissivity of bare tungsten and window absorptivity. The micro-optical pyrometer was calibrated against a National Bureau of Standards calibrated tungsten lamp and both pyrometers were periodically checked against the melting points of tungsten and molybdenum using the oxidation apparatus. Above 10-6 atm, pressures were measured with an Alphatron gage calibrated against a McCleod gage. At 10-6 atm, a hot-filament ionization gage was employed. A magnified image of the self-illuminated tungsten rod was formed using a 360-mm objective lens mounted outside the bell jar. When the experiment exceeded 1 hr, the image was focused on a ground-glass plate about 10 ft from the tungsten rod at about X8 and the recession of the thickness of this image was monitored with a Gaertner cathe-tometer. When faster rates were encountered, a 35-mm time-lapse cinecamera with a telephoto lens and bellows extension was substituted for the ground-glass plate and cathetometer. Diameter recession rates were determined from the photograph image projected on the screen of an analytical film reader. EXPERIMENTAL PROCEDURE After installing the rod in the apparatus and cleaning it with acetone, the system was evacuated to 5 1 x 10-5 torr. Before oxygen was introduced,

Jan 1, 1964

By W. A. Backofen, D. Lee

Tlze condition of superplasticity or neck-resistanl flow that results front high strain-rate sensitivity has been observed in isothermal tension tests on several titanium alloys and one of zirconium hi general, il was associated with reasonably fine-grain micro-structures being stvained in the transformation range at rates below i - 10 -3 sec-&apos;. The metallographic mean-free path, L, was measured at room temperature after rapid cooling from the temperature of test-ing. The flow stress of Ti-GAL-4V at 950°C was proportional to La at different constanl <; the value of a decreased with increasing. E but at E< 1.5 x 10-4 sec-1 it varied only from 0.9 to 1.25. The findings were interpreted to mean that viscous boundary shear is the rate-controlling process of deformation at high levels of strain rate sensitivity in these materials. Elongation of over 1000 pet could be obtained, but a1 temperatures so high and rates so low that any practical application of the full effect would probably be difficult. As the transformation range was narrowed, by turning from Ti-6AL-4V to Ti-5Al-2.5sn to nomznally pure titanium, the allowable temperature varialion was correspondingly reduced. Superplasticily was not found in Armco iron, presumably because the transformation range was too narrow to allow the developtnenl of a reasonably stable microstructure for isolhermal lesting. THE work represented by this paper grew out of a recent study of texture hardening in a(hcp) titanium and zirconium-alloy sheet,&apos; of which part has now been published.2 It was found that, with heating, the tensile plastic-anisotropy index, R,* was decreased from well above 1 towards 1 as the temperature range for the a(hcp) -ß(bcc) phase change was entered. The clearest example of that trend is illustrated with previously unpublished data in Fig. 1. It might have been thought that such a development resulted simply from introduction of the cubic and therefore plastically less anisotropic phase. However, the accompanying change in the index of tensile strain-rate sensitivity, m = a log a/a log E, was rapidly upwards, to a high of 0.85 in some cases (also illustrated in Fig. 1). At the same time, the total tensile elongation rose to a maximum and the flow strength dropped away as R (and m) approached 1. Taken together, the observations cannot be understood as resulting from the presence of cubic phase, per se. It has been concluded instead that they reflect the largely noncrystallographic deformation which characterizes superplasticity. As demonstrated in other recent work? a necessary condition for super-plasticity is strain-rate sensitivity of flow stress sufficiently high that m is above a lower limit of -0.3. The origin of large m has been traced, in turn, to grain size so small that a substantial amount of viscous deformation is introduced by such processes as Nabarro-Herring diffusional flow4 and/or grain boundary shear.5,6 Because of problems in the processing of titanium and zirconium alloys—problems of high strength, limited ductility, and excessive springback, originating largely in slip resistance-it was natural to wonder if something useful might be done with superplasticity in those materials. Therefore experiments were made for more closely identifying and generally bounding the phenomenon with temperature and strain-rate limits, before attempting to decide about its exploitation. The results are being reported here. EXPERIMENTAL Materials. The two of primary interest were the titanium alloys of nominal composition (in wt pct) 5A1-2.5Sn and 6A1-4V. Others were a 4A1-1/4O2 titanium alloy, titanium of commercial purity (RC-70), Zircaloy-4. and Armco iron. All were received as annealed 3/16 in. thick sheet, except RC-70 which was & in. thick, and tested in that condition. Details of transformation temperature and grain size are given in Table I. The results of dilatometry for the measurement of transformation temperatures were unsatisfactory. Data were finally obtained by metallographic examination of each specimen after test, to determine from the amount of transformed 4 where the specimen had been heated in relation to the critical temperatures. Results were in reasonable agreement with information from the supplier. Strip tensile specimens were of full sheet thickness and taken along the rolling direction, except for those

Jan 1, 1968

By T. H. Alden

Using alternating tension-compression straining, the hardening of magnesium oxide single crystals was studied up to large stresses and strains. At 0.25 pct plastic strain amplitude, the hardening curve is approximately linear with slope 25,000 psi from the shear yield stress, 7 to 8000 psi, to 35,000psi. Above this stress, the slope decreases. The strain hardening behavior of MgO is considered qualitatively similar to that of metal single crystals. The relatively high stress attainable by strain hardening is associated apparently with the high yield stress on the cross-slip system, (001) <110>. Cleavage fracture during testing is uncommon. It is argued that the centers of high internal stress at glide band intersections, at which cracks tend to nucleate, are dispersed by cyclic strain. Special features of the glide band structure produced by cyclic strain and revealed by dislocation etch pits, support this view. Strain hardened MgO has mechanical properties greatly superior to the as-received material: yield stress, greater than 100,000 psi; elongation to fracture about 1 pct. A material is said to strain harden if the yield stress increases with an increment of plastic strain. This definition is usually applied for straining done in one direction, but is also applicable when the strain direction is periodically reversed, Fig. 1. For certain metal single crystals, data are available which permit a comparison of the hardening behavior for cyclic straining and for tension straining.&apos;-4 With certain qualifications, these data show that the same processes of hardening are operative in each type of test.5 Despite this fact, the importance of the technique is not immediately evident, although tension-compression studies of the common metals appear to suggest some deficiencies in theories of strain hardening developed exclusively on the basis of tensile tests. However, a recent observation suggests that the cyclic straining method may be very useful for studying semibrittle crystals in which large plastic strains are not accessible in unidirectional testing. The observation is that zinc crystals, when strained in tension-compression at -52°C, do not fail by cleavage at low stress (-500 psi)6 as they do in tension, but harden to a limiting stress of more than 5000 psi over a total plastic strain of about 600 pct.2 An important characteristic of the behavior of zinc crystals is the high stress, relative to the yield stress, attainable by strain hardening. By comparison, the hardening of aluminum single crystals tested by an identical technique saturates at 1100 psi. This difference is best explained by the cross-slip hypothesis of dynamic recovery.7,8 In zinc, cross slip is difficult because of the high yield stress for glide on planes other than the basal plane in the < 1120 > zone. The present work was undertaken in order to test whether these methods and ideas are applicable to other materials. Magnesium oxide single crystals, in common with most crystals of the rock-salt structure, deform plastically but fail by cleavage after a small strain when tested in tension. It was hoped that larger strains would be attained using tension-compression. There is, in addition, evidence 8a which shows that slip on the probable cross system, (001) < 110>, is difficult in magnesium oxide; it may therefore be possible to attain high stresses by strain hardening. 1) EXPERIMENTAL PROCEDURE Experimental methods used in this study were based in part on techniques reported in papers of Stokes, Johnston, and Li.&apos; MgO blocks, purchased from Norton Co., were used without further annealing. Specimens were cleaved to dimensions approximately 0.125 in. sq and 1 in. in length. The gage section, formed by chemical polishing, was sprinkled with 280 mesh silicon carbide particles in order to introduce fresh dislocations. The crystals were then cemented into cylindrical aluminum adapters and clamped in an Instron testing machine. One of two alternating straining programs was used. In the first, total cross-head travel was established and increased in steps after various numbers of cycles. In the second, a capacitance gage was used to directly measure the elongation of the specimen and the crosshead was controlled so as to keep the plastic strain amplitude constant. The straining was always symmetrical with respect to the initial, zero strain condition. While both procedures produce strain hardening, only the latter permits a measure of the total plastic strain so that hardening curves may be drawn. Constant plastic strain amplitude tests were done

Jan 1, 1963

By Nicholas J. Grant, John S. Benjamin

A series of composite alloys containing a high volume of NiAl, Ni3Ah or CoAl, bonded with 0 to 40 vol pct of a ductile metal phase, were prepared by powder blending and hot extrusion. The binder metals were of four types: pure nickel or cobalt, near saturated solid solutions of aluminum in nickel and cobalt, type 316 stainless steel, and niobium. Sound extrusions were obtained in almost all instances. Studied or measured were the following: interaction between the alunzinides and the binders, room-temperature modulus of rupture values, 1500° and 1800°F stress rupture properties, hardness, structure, and oxidation resistance. Stable structures can be produced for 1800°F exposure, with interesting high-temperature strength and good high-temperature ductility. Oxidation resistance was excellent. A large number of experimental investigations have been made of the role of structure on the properties of cermets and composite materials. Gurland,1 Kreimer et al.,2 and Gurland and Bardzil3 have indicated the preferred particle size in carbide base cermets to be about 1 µ, with a hard phase content of 60 to 80 vol pct. The optimum ductile binder thickness was noted to be 0.3 to 0.6 µ.1 Complete separation of the hard phase particles by the binder is important in reducing the severity of brittle fracture.&apos; The purpose of the present study was to produce structures comparable to the conventional cermets, using a series of relatively close-packed intermetal-lic compounds rather than carbides as the refractory hard phase, and to study the effects of binder content and composition on both high- and low-temperature properties. The selected intermetallic compounds were particularly of interest because of the potential they offered in yielding room-temperature ductility. The highly symmetrical structures are known to possess high-temperature ductility and room-temperature toughness. Based on a ductile binder, the alloys were prepared by the powder-metallurgy route to avoid melting and subsequent alloying of the matrix, and were extruded at relatively low temperatures. It was expected that the composite alloy would retain useful ductility. In contrast, infiltration and high-temperature sintering led to alloying of the matrix and to decreased ductility. The systems Ni-A1 and Co-A1 were selected for this study. In the Ni-A1 system the compounds NiA1, having an ordered bcc B2 structure, and Ni3Al(?1), having an ordered fcc L12 structure, were chosen. In the system Co-A1 the intermetallic compound CoAl with an ordered bcc B2 structure was used. ALLOY PREPARATION The intermetallic compounds, see Table I, were prepared by using master alloys of Ni-A1 and CO-A1, with additions of either cobalt or nickel to achieve the desired compositions. The master alloy in crushed, homogenized form, was melted with pure nickel or cobalt in an inert atmosphere, cold copper crucible, nonconsumable tungsten arc furnace. The resultant intermetallic compounds were homogenized at 2192°C in argon, crushed, and dry ball-milled in a stainless mill to -100 and -325 mesh for the Ni-A1 compounds and to -325 mesh for the CoAl compound. Finer fractions were separated for some of the composite alloys. Several ductile binders were utilized. These included Inco B nickel, 5µ ; pure cobalt, 5 µ, from Sher-ritt Gordon Mines, Ltd.; fine (-325 mesh) niobium hydride powder; fine (15 µ) type 316 stainless-steel powder; and near-saturated Ni-A1 and Co-A1 solid-solution alloys, also in fine powder form. The niobium hydride was decomposed above about 700°C in processing of the compacts in vacuum to produce niobium powder. The Ni-7.1 pct A1 and the Co-5.3 pct A1 solid-solution alloys were prepared from pure nickel or cobalt and pure aluminum by nonconsumable tungsten arc melting under an inert atmosphere. The ingots were homogenized, lathe-turned to fine chips, and dry ball-milled in air to -325 mesh powder. These solid-solution alloys are designated NiSS and CoSS; see Table I. Subsequently the hard and ductile phases were dry ball-milled as a blend. Experiments clearly established the need to coat the hard particles with the ductile binder to optimize subsequent hot compaction by extrusion. Ordinary dry mixing usually resulted in nonhomogeneous alloys which were quite brittle. Conventional cermets are consolidated by liquid phase sinteiing or infiltration, which resulis in undesirable and uncontrolled alloying of the binder phase. For this study, a loose (unsintered) powder-extrusion process was emploved, minimizing reactions between binder and hard particle, thereby permitting much greater control of composition and structure. The constituent powders were first mixed in the desired

Jan 1, 1967

By R. D. Nelson, J. C. Shyne

The ß and a ß transformations in plutonium were studied with particular emphasis on the transformation kinetics and microstructure. Significant observations are: 1) The kinetic data show conclusively that the ß — a transformation in high-purity plutonium can proceed isothermally with no athermal component. 2) Plastic deformation of the stable (3 phase retards the subsequent (3 — a transformation. 3) Plastic deformation of the stable a phase accelerates the a — ß transformation; the acceleration is attributed only to residual stresses. 4) The a and a?a volume changes occur anisotroPically in textured plutonium. 5) An apparent crystallogvaphic relationship exists between the parent and the product phases of the and (3 — a transformations. 6) Both applied uniaxial compressive stresses and uniaxial tensile stresses raise the starting temperature for the ß — a transformation. 7) A given uniaxial tensile stress favors the a — ß transformation more than an equivalent applied uniaxial compressive stress opposes the transformation. These observations of the (ß —a and a — ß phase changes in plutonium are consistent with known mar-tensitic transformations. ThIS paper elucidates some of the characteristics of the a— ß and ß —a transformations in plutonium. Because considerable conjecture exists about the mechanisms by which the phase transformations occur in plutonium, experiments have been performed to provide indirect information concerning the mechanisms responsible for the a —ß and ß -a transformations. Indirect information is of particular value in the study of plutonium because of the experimental difficulties presented by the metal. Single crystals have not been produced in any of the allotropes. The large density results in high X-ray and electron-absorption factors and consequently complicating X-ray and electron diffraction. The kinetics of ß — a and a — ß transformations of plutonium and the behavior of the transformations under a variety of conditions have been investigated in detail. Information about the mechanisms of the allo-tropic transformations of plutonium was obtained indirectly from three sources: 1) the effect of plastic deformation of the stable parent phase upon the transformation kinetics; 2) the behavior of the metal transforming under applied stresses; and 3) the microstruc-tural and crystallographic features between parent and product phases. PHASE-TRANSFORMATION CHARACTERISTICS In characterizing solid-state phase transformations in metals and alloys, it is useful to define several types of transformations. An aim of the present work was to identify the low-temperature transformations in plutonium by type, i.e., as martensitic or nonmar-tensitic. Practical definitions for these terms follow. The terms commonly used to categorize phase transformations lack universally accepted definitions. This confusion arises doubtlessly because some terms specify crystallographic or morphological character while other words have a kinetic or a thermodynamic connotation. For example, martensitic specifies certain definite crystallographic restrictions. Unfortunately, martensitic is sometimes used in an ill-defined way to imply kinetic characteristics. Further confusion attends the use of such expressions as nucleation and growth, diffusional, and massive. From time to time new systems of phase-transformation nomenclature are suggested; unfortunately none of these has gained general acceptance.1,2 The authors of the present paper have no intention of entering the controversy. We recognize that some readers may object to the nomencliture used here. For exampie, the terms military and civilian have recently been used in much the same way as martensitic and non-martensitic are used in this paper. This paper is intended to describe several specific details of the low-temperature phase transformations in plutonium. The authors have found it useful to identify these transformations as martensitic; the term was chosen as the best available to describe the experimentally observed features of the transformations studied. A martensitic transformation is one that occurs by the cooperative movement of many atoms; the rearrangement of atoms from parent to product crystal structure occurs by the passage of a mobile semico-herent growth interface. The geometric features characteristic of a martensitic transformation are a specific orientation relationship between the product and parent phase lattices, a specific habit-plane orientation for the growth interface, and a shape change with a specifically oriented shear component. There is no alloy partition between the parent and product phases in a martensitic transformation. Martensitic transformations may display either athermal kinetic behavior or thermally activated isothermal kinetic behavior. Some martensitic transformations occur isothermally, although more commonly martensitic transformations are athermal. Isothermal martensitic transformations are suppressible by rapid cooling. In athermal martensitic transformations, nucleation and growth are not thermally activated and the transformations are essentially time-independent. Nucleation, growth, or both can be thermally activated in isothermal martensitic reactions. Transformation of the parent phase into a marten-

Jan 1, 1967

By J. L. Lehman, J. D. Sudbury, J. E. Landers, W. D. Greathouse

A full scale field experiment on cathodic protection of casing answers questions concerning (1) the proper criteria for determining current requirments, (2) the amount of protection provided by different currents, and (3) the transfer of current at the base of the surface pipe. Three dry holes in the Trico pool in Rooks County, Kans., were selected for cathodic protection tests. The three holes were in an area where casing failures opposite the Dakota water sand often accur in less than a year. Examination of the electric togs showed the wells to be similar to other wells in the field where casing in four of seven producing wells has failed. The three holes were cleaned out and cased with 75 joints of new 51/2-in. 14-tb J-55. Each joint was visually inspected and marked before it as run. The casing was bull plugged and floated in the hole 50 that the inside might remain dry and free of excessive attack. Also, if a leak occurred, a pressure increase could be observed on gawge at the surface. Extensive testing was done, including potential profiles, log current-potentid curves and electrode measurements from both surface and downhole connections. Based on these data, a current of 12 amps was applied to one well and 4 amps to mother. The third well was left to corrode. During the two-year period when the casing was in the ground, [he applied current was checked weekly, and reference electrode measurements were made about every two months. Three sets of casing potential profi1e.c were run. When the three strings were pulled, each joint was examined for type of scale formed, presence of sulfate-reducing bacteria, extent of corrosion nttnck and pit depth. Since the pipe was new when run, quantitative determination of the protection provided by current was possible. This is the first concrete field evidence to help resolve the many arguments about the proper method for selecting adequate current for cathodic protection of oilwell (-using. INTRODUCTION A casing string is run when a well is drilled. This pipe is supposed to protect this valuable "hole in the ground" for the life of the well. Often the casing does not last the life of the well; it is with these casing failures that this work is concerned. The cost of repairing a casing failure varies from field to field—from as much as a $30,000 per leak average in California to $5,000 per leak in Kansas. Additional costs other than actual repairs are also important. These include formation damage, lost production, etc. Casing damage caused by internal corrosion is important in some areas. Treatment normally consists of flushing inhibitor down the annulus, but further research is being done on control measures. The test described in this paper is concerned only with external corrosion. The problem of casing failure from external attack has appeared in several areas including western Kansas, California, Montana, Wyoming, Texas, Arkansas and Mississippi. Cathodic protection is currently being used in an attempt to control external corrosion. From reports in the NACE there are thousands of wells currently under cathodic protection. The quantity of current being applied ranges from 27 amps on some deep California wells to a few tenths of an amp being supplied from magnesium anodes on wells in Texas and Kansas. Considerable field and laboratory effort1,9,5,6 was exented on the problem of cathodic prctection of casing, and it became fairly obvious that this method could be used to protect wells. Early workers showed that current applied to a well distributed itself over the length of the casing and was not concentrated on the upper few hundred feet. Basic cathodic protection theory had shown that corrosion attack could be stopped by applying sufficient current. The problem resolved itself, then, into one of trying to decide just how much current was necessary. Various criteria were utilized in installing the many existing cathodic protection installations. These methods included the following. 1. Applying sufficient current to remove the anodic slope as shown by the potential profile." 7. Applying enough current to maintain all areas of the casing at a pipe-to-soil potential of .85 v.&apos; 3. Applying the current indicated by a log current-potential (or E log I) curve." 4. Supplying the current necessary to shift the pipe to-soil potential .3 v." 5. Applying 2 or 3 milliamps of current per sq ft of casing."

By C. D. Williams, C. E. Ells

The susceptibility of quenched and aged Zr-2.5 wt pct Nb alloy to embritt2ement during irradiation has been examined for a number of solution temperatures and aging times. Material quenched from temperatures approximately 40°C below the transus has high tensile ductility, and this ductility is insensitive to aging at 500°C or to irradiation. If, however, the material is quenched from temperatures above the transus it becomes highly susceptible to loss of ductility either from aging at 500 or from irradiation. Inter granular failure is characteristic of the materials having low ductility. The distribution of the equilibrium phase is found to control the susceptibility to embrittlement by restricting 6 grain growth during heat treatment and thus influencing crack propagation. IN zirconium, as in titanium, -stabilizing alloy additions are used to obtain high strengths via quench and age heat treatments, and the Zr-2.5 pct Nb alloy has been developed1 because of its strength advantage over the Zircaloys. Early in the development of the Zr-2.5 pct Nb alloy the problem of 13 embrittlement was appreciated, and for this reason the solution temperature was chosen below the p transus.&apos; In the course of irradiation studies on quenched and aged Zr-2.5 wt pct Nb alloy it was found&apos; that irradiation introduced an important aspect of p embrittlement, riz., material quenched from the phase and aged 24 hr at 500°C was severely embrittled by moderate doses of neutron irradiation. This effect had not been studied in titanium alloys. In titanium the metallurgical features leading to 0 ernbrittlement were found to be structures with: a) coarse a platelets at the grain bondaries, b) finely dispersed a uniformly distributed throughout the (0) matrix,6 c) Widmanstatten a-13 with more than 50 pct P, d) the presence of some metastable p transformation products,3 and e) large prior -phase grain size.5 Alternatively, the presence of a uniform distribution of coarse a was conducive to high ductility and a structure largely of equiaxed a was very dctile. The detailed mechanisms of the embrittlement have not been worked out for all of these conditions, although weakness at either a-matrix boundaries or prior p grain boundaries have been prominent in the eculation. It was proposed that acicular a might act as a mild notch, and low ductility has been associated with easy fracture along its boundary.&apos; There have been two opposing suggestions for the source of the high ductility associated with equiaxed a phase. JaffeeB proposed that this a would accept a large por- tion of the oxygen, thus increasing the ductility of the matrix, whereas after study of a Zr-Nb-Cu alloy Weinstein and oltz proposed that the a phase, softer than the martensitic matrix, acted to blunt cracks formed in the matrix. In the present work we have studied the effect of neutron irradiation on the ductility, particularly the P embrittlement, of the Zr-2.5 wt pct Nb alloy. By a variation of solution temperature and aging time a variety of metallurgical conditions have been examined, and a range of resultant ductilities obtained. The ductility has been related to the material microstructure and mode of fracture. EXPERIMENTAL The alloy used in the present work came from two separate ingots fabricated into rod of 3/8 or i in. diam, Table I. For both batches the P transus temperature was approximately 890° C. Most of the heat treatments were done directly on lengths of the j} in. diam rod, after which the tensile test specimens were machined. Quenching was achieved by dropping rods from a dynamic vacuum into water, the cooling rate estimated to be 2 100°C per sec. For aging the rods were encapsulated in evacuated silica tubes. Round tensile test specimens, with gage diam and length 0.160 and 1.0 in., respectively, were used throughout and pulled at room temperature or 300°C on Instron tensile machines, at a crosshead speed of 0.05 ipm. Specimens were irradiated in the NRX and NRU reactors, in facilities described in previous publications.&apos;0 The metallurgical conditions examined have been: All tensile test specimens were machined with axes in the axial direction of the swaged rod. Although the specimen had a degree of preferred crystallo-graphic orientation with basal plane normals both parallel with and perpendicular to the tensile axis, the material was comparatively isotropic." The techniques of thin foil examination in the electron micro-

Jan 1, 1970