Search Documents

By E. Miller, J. M. Eldridge, K. L. Komarek

The liquidus curve of the Mg-Pb system was accurately redetermined. The compound Mg2Pb decomposes peritectically at 538.2° ± 0.3°C to liquid and to a compound p' which melts congruently at 35.0 at. pct Pb and 549.0° ± 0.3°C. The solidus curve of ß' was determined. X-ray diffraction studies indicate that 4' has an orthorhombic structure. Activity values of magnesium calculated from the phase diagram agree with those published in the literature. EXPERIMENTAL thermodynamic properties of binary metallic systems have to be consistent with values calculated from the phase diagram. In systems forming intermetallic compounds the shape of the liquidus curve near a compound is determined by the thermodynamic properties of the coexisting solid and liquid phases. Hauffe and Wagner' neglected the temperature dependence of the chemical potentials and obtained the potential differences of the components of the liquid alloys, relative to stoichiometric liquid. Their calculations were based on the liquidus curve and on the heat of fusion of the compound, and were only valid near the congruent melting point. Steiner, Miller, and Komarek2 developed equations which account for the temperature dependence and obtained the chemical potentials of liquid Mg-Sn alloys over the entire phase diagram from the liquidus and solidus curves and from enthalpy values with the pure components as the standard states. The Mg-Pb phase diagram has been studied by several investigators whose results have been compiled and critically evaluated by Hansen.3 Although the liquidus curve was poorly defined, the general features of the diagram, i.e., one congruent melting compound, Mg2Pb, of essentially stoichiometric composition, two eutectics, and limited terminal solid solubilities, seemed to be suitable for a similar thermodynamic analysis. A careful redeter-mination of the liquidus by thermal analysis revealed, however, the existence of another compound. The liquidus curve between the two eutectics was precisely delineated and the structure and solidus curve of the new compound were investigated. The revised phase diagram was thermodynamic ally analyzed to evaluate the activity of magnesium in the liquid alloys. EXPERIMENTAL PROCEDURE The magnesium metal (Dominion Magnesium Ltd., Toronto, Canada) had a purity of 99.99+ pct; lead (American Smelting and Refining Co.) contained 99.999 pct Pb. Most experiments were carried out in graphite crucibles. Several experiments were made in high-purity alumina (Triangle R.R., Mor-ganite, Inc.) and in Armco iron crucibles to test the inertness of the graphite crucibles. Chemical analysis of magnesium and detailed description of the procedure for thermal analysis have been given previously. For the determination of the solidus curve of the compounds, specimens of initial composition Mg2Pb were equilibrated in a closed isothermal system with magnesium vapor. The source of the magnesium vapor was an alloy which had a gross composition lying in the 0' + L field at the temperature of equilibration. As equilibrium was approached, the specimens lost magnesium to the two-phase reservoir thereby lowering the activity of magnesium in the specimens until activity and composition equaled that of the ß'/ß' + L boundary. Crucibles (1.9 cm ID by 2.2 cm OD by 4.1 cm high) and tightly fitting lids were machined from a molybdenum rod; small, shallow trays were fashioned from thin (0.005 in.) molybdenum sheet, and all the molybdenum components were degreased in hot carbon tetrachloride and then dried. The pieces were then degassed in vacuum at 950°C for about 6 hr. The two-phase alloy was placed at the bottom of the crucible and small specimens of the Mg2Pb compound, weighed on an analytical balance, were placed in two molybdenum trays above the two-phase alloy. The crucible was closed by forcing its lid on and then inserted in a titanium crucible. This crucible was evacuated, flushed twice with argon, and welded under argon. The specimens were equilibrated for about 1 week in a resistance furnace regulated by a Celectray controller, and the runs were terminated by water quenching. The specimens were again weighed and the equilibrium compositions were calculated on the basis that the weight losses were solely due to a loss of magnesium to the two-phase alloy. The structure of the B' phase was investigated by the Debye-Scherrer X-ray diffraction technique. Selected ingots from thermal-analysis experiments containing about 35 at. pct Pb were re-melted, slowly cooled, and crushed in an argon-filled glovebox until the entire ingot passed through a 50-mesh sieve. The powder was thoroughly

Jan 1, 1965

By J. C. Trantham, J. W. Marx

From 1955 to 1958 the Phillips Petroleum Co. conducted a series of small scale counterflow combustion field tests in a tar sand about 60-ft deep and 6 to 12-ft thick near Bellamy, Mo. A total of seven different well patterns, including conventional five-spots and seven-spots plus a 15-well line drive pattern and a 10-well radial pattern, were employed. Electric heaters, gas burners and wellbore fuel packs were tested as counterflow ignition devices. Direct drive ignition followed by reversal to counterflow operation was not possible in this case because of formation plugging by the semi-solid tar during the direct drive phase. Sustained counterflow burning was achieved with wellbore fuel packs under conirolled conditions which permitted close correlation of fire front velocity, air velocity, air-oil ratios and yields for a wide variation in process parameters. The tar in place was about 10' APl with a reservoir viscosity greater than 500,000 cp. The composite oil prodlcct was 26' API with a viscosity in the range of 5 to 15 cp. Vertical sweep efficiency in the line drive pattern was essentially 100 per cent, with no evidence of gravity segregation. Original tar in place ranged between 800 and 1,000 bbllacre-ft, specific rock permeability averaged about 800 md before burning and effective air pemeability with residual oil and water in place (at the time of ignition) averaged 250 md. The volume of oil recovered during stabilized line drive counterflow burning represented about 67 per cent of the volume of tar originally in place in the burned out zones. A minimum was found when air-oil ratios were plotted against formation air velocities, and a limiting air velocity existed below which the counterflow fire front reversed and burned back over its own trajectory, using the residual coke left behind. INTRODUCTION Early in 1955 the Phillips Petroleum Co. began preparations to field test counterflow underground combustion as a method for producing oil from high viscosity hydrocarbon deposits, such as bituminous (tar) sands. At that time all published information on the use of underground burning io increase oil recovery was based on the direct drive process, in which the fire front moved through the formatim in the same direction as the injected air stream. Such direct burning is not applicable to many heavy oil sands or to most tar sands because the heat-thinned native hydrocarbon congeals in the cold rock ahead of the fire front forming a gas permeability block which smothers the combustion. Laboratory experiments first demonstrated that this permeability blocking would not occur if the fire front and the air stream moved in opposite directions. In this counterflow (reverse) burning process the heated heavy oil or tar is driven back through the combustion zone. Here thermal cracking produces relatively light hydrocarbon products which pass through the heated rock behind the fire front (largely in the vapor phase) and are incapable of causing a gas permeability block.' Exploratory wring revealed that consolidated bituminous sandstones with a combination of tar saturation, permeability, thickness and depth favorable for experimental field testing existed at several points in western Missouri. By the fall of 1955, a test site for determining technical feasibility of the counterflow process under field conditions had been selected near Bellamy, Vernon County, Mo. — about fifty miles north of Joplin. The pay zone was too thin and too shallow to constitute a commercial prospect, but these same factors permitted controlled experimental operation with a small compressor installation and with a large number of monitor wells. These were needed for adequate observation of the underground phenomena at reasonable cost. RESERVOIR CHARACTERISTICS The reservoir chosen for the experimental field tests was a 124 thick section of tar sand extending from 49 to 61 ft subsurface, with shale and siltstone laminations sealing the top and bottom. This section was part of a larger 30-ft thick tar sand deposit which extended both above and below the test zone. Core analyses showed that the 12-ft sand was effectively subdivided into two approximately equal sections, with the lower zone being consistently more permeable than the upper zone. The most significant laboratory core data are summarized in Table 1. The line drive test which is the principal subject of this report utilized only the lower 6-ft thick zone, with the upper zone regarded as part of the 55-ft overburden. WELL PATTERNS The over-all field test program involved a total of seven different well patterns, including conventional five-spots and seven-spots plus a 15-well line drive pattern and a 10-well radial pattern. In some of the tests the full 12-ft zone was employed; in other cases only the more perme-

Jan 1, 1967

By N. A. D. Parlee

The diffusion rate of hydrogen in liquid iron has been measured by a gas-liquid metal diffusion cell technique. The diffusion cell was formed by immersing an alumina tube containing hydrogen gas at 1 atm in a bath of stagnant liquid iron. The change in the composition of the melt in the cell was determined by measuring the rate of absorption of the gas in the cell. The appropriate solution to Fick's second law was used to examine the data and calculate diffusivi-ties. The absorption of hydrogen in stagnant pure liquid iron has been found to be diffusion-controlled. The results show that the chemical diffusion coefficient, D, of hydrogen in pure iron in the range of 1547" to 1726°C can be represented by the following Arrhenius relation: D(sq cnz per sec) = 3.2 x X exp(- 3300 i 1800/RT) where the uncertainty in the activation energy corresponds to the YO pct confidence level. Oxygen in the melt (above 0.015 pct 2) increased the apparent rate of absorption of hydrogen. The importance of diffusion data on liquid metals for predicting the rates of certain metallurgical processes has been recognized for a long time. Moreover, these data are much needed to test and develop theory for diffusion in liquid metals. Despite this practical and theoretical interest, however, relatively little reliable information about diffusion in liquid metals is available in the literature. This is particularly true for gas components such as hydrogen, oxygen, and nitrogen in liquid metals, where almost no data on chemical diffusion coefficients are to be found. This is probably due to a multitude of experimental difficulties particularly associated with high-temperature melts. In an effort to fill this gap in information, a research program was undertaken to study the diffusivities and rates of solution of gases in liquid metals. This paper presents the results of a study of the diffusion of hydrogen in liquid iron. EXPERIMENTAL METHOD Two methods for the study of the kinetics of dissolution of gases in liquid metals are being employed in this laboratory. Both involve the measurement of the volume of gas absorbed by the melt as a function of time and as such both avoid the uncertainties involved in chemical analyses of quenched samples for relatively small amounts of gas. In the first method, the gas dissolves in an inductively stirred melt and, in the absence of a slow surface reaction, the results are often interpreted in terms of mass transport across a liquid "boundary layer" between the homogeneous gas phase and well-stirred part of the melt. Other interpretations of the results of such experiments have also been described in the literature.1'5 In the second method a gas-liquid metal diffusion cell is used.' The gas dissolves in a cylindrical column of stagnant liquid metal and, in the absence of a slow surface reaction, the results are interpreted in terms of a non-steady-state diffusion solution to Fick's second law. The weakness of the first method is that while it gives information on the mechanism of absorption by stirred melts it yields an overall rate constant which even in the simplest cases depends on the nature and the thickness of the "mass transport layer" or "boundary layer". It yields no values of diffusion coefficients. The second method was used in this research because in many cases it is possible to determine the diffusion coefficient of the gas component in the liquid metal. In this research it has been utilized to measure diffusion coefficients of hydrogen in liquid iron. The apparatus used was essentially the same as that described by Mizikar, Grace, and par lee but certain modifications have been introduced to meet the elevated temperatures and special conditions of this research. Fig. 1 is a schematic drawing of the apparatus and Table I gives the identification of various parts in this figure. The diffusion cell, shown in detail in Fig. 2, was formed by immersing an impervious alumina tube (hereafter called absorption tube) in a bath of pure liquid iron contained in an alumina crucible. Two types of tubes were used, Morganite triangle RR and McDanel AP35. The crucible was contained in a vertical impervious alumina combustion tube (32 mm ID by 914 mm long) which was closed at both ends by water-cooled brass heads employing O-ring compression seals, Fig. 1. A protection tube enclosing a Pt, 5 pct Rh-Pt, 20 pct Rh thermocouple was introduced through the lower end of the combustion tube

Jan 1, 1968

By M. Duclos, A. Sawatzky

A simple model has been developed which describes the steady-state solute distribution in Ti-H type systems above the eutectoid temperature in the presence of a temperature gradient. The solute distribution is dependent on the shape of the phase boundaries. An interesting result, and one that is not observed at steady state in thermal diffusion below the eutectoid temperature, is the existence of a two-phase region. The heat of transport for hydrogen in a titanium, Q*a, over the temperature range 275" to 650.C is determined to be 4500 * 230 cal per mole. The heat of transport for hydrogen in B titanium, QB* over the temperature range 320" to 590.C is found to be 630 ± 200 cal per mole. It is also shown that thermal diffusion provides a method by which phase bounduries above the eutectoid may be determined in Ti-H type systems. IN modern technology materials are being used at constantly increasing temperatures under greater temperature gradients. Thus atomic migration in metal alloys due to a temperature gradient (thermal diffusion) may in some cases occur to an observable extent. The thermal diffusion of hydrogen in zirconium has in recent years received considerable attention1-' because of the use of zirconium alloys in nuclear power reactors. The thermal diffusion kinetics below the eutectoid (547°C) are fairly well understood. At steady state the solid solution, a, and hydride, 6, phases are completely separated with the hydride precipitating at the lower temperatures. No experimental work has been carried out in the a + B region although Droege4 suggested that a complete separation of the two phases, as observed at temperatures below the eutectoid, might not always occur. In the present investigation a simple model has been used to determine the steady-state solute distribution under a temperature gradient in Zr-H type systems heated above the eutectoid temperature. The solute distribution is shown to be dependent on the shape of the phase boundaries in the constitutional diagrams and several typical cases are discussed. The model has been applied to Ti-H. This system was chosen in preference to Zr-H because of its much lower eutectoid temperature (-300°C as compared with 547.C), thereby reducing experimental errors due to oxidation and hydriding. The heats of transport for hydrogen in the a and B phases of titanium also have been determined since they were required to compare the proposed thermal diffusion model with experiment. THEORY In the presence of a temperature gradient the atomic flux in a single-phase region of a two-com-ponent system of which the atoms of only one component are diffusing is given by:' J = - U\dx + RT3 dx) which can be written as: j-D(dn/dt +Q*n/RT2)dt/dx [11 J - -D\dT + RT2)dx [1] where D = diffusion coefficient, n = solute concentration, T = absolute temperature, R = gas constant, dT/dx = temperature gradient, and Q* = heat of transport. At steady state (J = 0) Eq. [I] leads to the solute distribution: n = noexp Q*/RT where no = a constant depending on total solute content. The heat of transport Q* can be experimentally determined from the steady-state distribution. In the present paper we shall determine the solute distribution in systems having the constitutional diagram exemplified by Ti-H shown in Fig. l.' As shown, N,(T) and NB(T) are the equilibrium solute concentrations in the a and 0 phases at temperature T. Lines AA' and CC' define the region of interest to us. The following assumptions are made: 1) Steady-state conditions prevail. 2) In a single-phase region all points on an isotherm have the same thermodynamic potential so that the composition over an isotherm is uniform. If a two-phase region exists, thermodynamic equilibrium is found only at phase interfaces. However, we assume the component of the concentration gradient along an isotherm to be small so that the composition in each phase is approximately the same as at the interface and is given by the constitutional diagram, Fig. 1. 3) There is appreciable diffusion of only one component. 4) We shall consider only the case where Qa*, QB*, and Qg*, the heats of transport for solute diffusion in the a, B, and 6 phases, respectively, are positive. This has been observed for the thermal diffusion of hydrogen in zirconium3 and titanium.10 We will show that the steady-state solute distribution above the eutectoid is primarily determined by the heats of transport and the temperature dependence of Na(T) and Np(T). It may be quite different from the steady-state distribution below the eutectoid. For example, we will see that, under certain conditions,

Jan 1, 1970

By Neils Hansen

The microstructure of dispersion-strengthened aluminum aluminum-oxide products containing from 0.2 to 4.7 wt pct of aluminum oxide has been examined by optical and transmission electron microscopy, and the flow stress has been determined at room temperature and at 400C by tensile testing. Products were examined as recrystallized and as high-temperature extruded, and the microstructures consisted of a fine dispersion of oxide particles in a matrix divided by respectively recrystallized grain boundaries and subgrain boundaries. The flow stress (0.2 pct offset) at room temperature of recrystallized dispersion strengthened aluminum aluminum-oxide products is the superposition of dispersion strengthening and grain boundary strengthening. This superposition has been found to be linear. The flow stress (a) can be related to the grain size (t) by the Petch equation: ing content of oxide and k is a constant independent of the oxide content. For extruded products a similar relation has been found by replacing the grain size by the subgrain size. The k-value is of the same order for the two types of structure, which shows that the subgrain boundaries are as effective slip barriers as grain boundaries. Tensile testing at 400C of re-crystallized and extruded products shows that oxide dispersion strengthening is very effective, whereas the strengthening effect of grain boundaries and subgrain boundaries is small. THE microstructure of dispersion-strengthened products consists of hard particles finely distributed in a metal matrix. The strengthening effect of the dispersed phase has been fairly well established,1 and it has been found that the size and volume fractions of the dispersed particles are important structural parameters. However, in many dispersion-strengthened products which have been worked and heat-treated during manufacture the matrix is divided into well-defined grains or sub-grains, which may also have a strengthening effect. A model of the matrix strengthening in dispersed products worked during manufacture has been proposed,2 introducing the energy of the structure as a strengthening factor, especially at low temperatures. A difficulty in this model is, however, to relate this (stored) energy to the structural parameters directly observable as for instance grain size. The strengthening effect of the matrix grain size after recrystallization has been in- vestigated for nickel-thoria (TD-Nickel) products3 and for copper aluminum-oxide products. Conclusive results were, however, not obtained as the grain size of TD-nickel was constant. 5 to II , after recrystallization at temperatures from 700 to 1200°C and as the copper products containing 5 to 1 wt pct of aluminum oxide could not be recrystallized even after severe cold reduction and heat treatment at 1050C. For aluminum aluminum-oxide products containing from 1 to 5 wt pct of aluminum oxide it has been shown that the tensile strength at room temperature decreases when an extruded product is cold-worked and recrystallized. The matrix in the extruded products is divided into well-defined subgrains of micron size, and as the grain size of the recrystallized products is about two orders of magnitude higher, it is obvious that grain boundary strengthening occurs. Preliminary results8 have indicated that the flow stress containing no grain boundaries, A is a constant and t is the subgrain size. At elevated temperatures the effect of boundaries is more complex; it has been shown11 that recrystallized products having an oxide content of about 3 wt pct are more creep resistant than extruded material in the temperature range 400° to 600°C, whereas on application of a higher strain rate the tensile flow stress (0.2 pct offset) is higher in extruded than in recrystallized aluminum—5 wt pct aluminum oxide products at temperatures from room temperature to 427°C (800), Finally it has been shown12 that the Brinell hardness at 350°C of extruded products having about the same content of aluminum oxide increases with decreasing grain size, determined by X-ray line-width measurements. The present study was undertaken to obtain a quantitative relationship between the tensile strength and the grain size of aluminum aluminum-oxide products in the recrystallized as well as in the extruded state. The tensile testing was performed at room temperature and at 400uC. The grain size of the recrystallized products was varied by changing the degree of cold-work preceding the recrystallization heat treatment. In extruded products grain (or subgrain) size variations were obtained by high-temperature heat treatment after extrusion. EXPERIMENTAL a) Materials. Aluminum aluminum-oxide products have been manufactured by consolidation of aluminum powder covered with a layer of aluminum oxide formed during powder manufacturing. The products examined were manufactured from atomized powder containing

Jan 1, 1970

By John N. Dew, William L. Martin, `

This paper describes the results of a laboratory investigation conducted to obtain data for an evaluation of the in situ combustion process as a method of producing crude oil from reservoirs. Air and fuel requirements, rates of advance, com-bustion temperatures, and coke and fluid distributions are presented. The mechanism of oil recovery by in stiu combustion is discussed. Five crude oils ranging in gravity from 10.9 to 34.2"' API were prodrrced from a semiadiabatic, uncon-.solidnted sand pack by in situ combustion. Experimental conditions were varied over a wide range in order to determine the inter-relation-.ships of process variables. The mini-mum air flux requirement for self-sustained combustion was found to he less than 10 scf/hr-ft'l. The rate of advance of a self-sustained combustion zone was found to be nearly proportional to the air flux at the combustion front. The effects of presrure and injected air flux were studied in a series of experiments using a 21.2" API crude. A minimum air require-ment was observed at an air .flux of 20 scf/hr-ft'. The oil saturation con-sumed as fuel averaged 5.5 per cent of pore volume. The effect of air pressure was, found to be .small for experiments having high combustion eficiencies. This study should promote a better understanding of the problems and mechanisms involved in labora-tory investigations and field applications of the in situ combustion pro-cess. The data presented will be use- ful in the interpretation of results of field tests. When tempered with volu-metric sweep efficiencies, the data can be used in making preliminary economic appraisals of the process as applied to reservoirs containing high porosity unconsolidated media. INTRODUCTION The purpose of this work was to obtain laboratory data for an evaluation of the in situ combustion process as a method of producing crude oil from reservoirs. In situ combustion basically consists of (1) injecting air into a reservoir through selected input wells to create an air sweep through the reservoir, (2) igniting the crude at the injection well, and (3) propagating the combustion front through the reservoir by continued air injection. By this means, oil is swept toward producing wells in the area. The fuel for combustion is supplied by heavy residual material (coke) which has been deposited on the sand grains during distillation and cracking of the crude oil ahead of the combustion front. Recovery of petroleum by a combustion or heat wave process is not a new idea. F. A. Howard was granted a patent in 1923 on a process in which air and a combustible gas were pumped into an injection well and ignited.' Russian engineers reported on field experiments with a crude oil gasification process in 1935'. Other known early field tests include those conducted near Bar-tlesville and Ardmore, Okla., in 1942." More recently completed field tests include an inverted seven-spot by Sinclair Oil Co. in the Delaware-Childers field, Nowata County, Okla.'; a three-well and an inverted five-spot test by Magnolia Petroleum Co. in Jefferson County, Okla."."; and a test by California Research Corp. in the Irvine-Furnace field in Kentucky. The Worthington Corp. has completed a test in cooperation with the Forest Oil Corp. in Clark County, 111.l Several field tests are now in progress. Sinclair has acquired a 600-acre lease in the Humboldt-Chanute field, Allen County, Kans., and is under way with a large-scale operation. Three field tests are under way in California. The General Petroleum Corp. is conducting an inverted five-spot pattern test in the South Bel-ridge field in Kern County under a cooperative agreement with 11 other companies, including Continental Oil Co. California Research Corp. is conducting a four-well pattern test in Midway-Sunset field near Maricopa, and Richfield Oil Corp. is under way with a test in the Ojai field in Ventura County. Although the published information is valuable concerning results of field tests, little laboratory data other than that reported by Kuhn and Koch5 are available to aid in appraising the tests from a technical or economic standpoint. Engineering data needed to evaluate the process include the amount of air required per barrel of oil recovered, minimum injection rates which will support combustion, rates of advance, air required per unit volume of reservoir cleaned, amount of oil recovered, and amount of oil consumed as fuel. The present laboratory investigation was undertaken to provide these data for that portion of the reservoir swept by the combustion zone. The first phase of this investigation was exploratory in nature and was conducted at injection pressures less than 100 psig. Data were ob-

By L. A. Geoffrion, R. H. Perkins, J. C. Biery

Densities of cerium metal and several lour-melting binary cerium alloys were measured over the range 25° to 800°C. A rolumeter, using NaK as working fluid, was used to obtain the data. The cerium, Ce-Co, Ce-Ni, and Ce-Cu alloys all exhibited an increase in density on melting, while a Ce-Mn alloy expanded on melting. FOR the proper design of a nuclear reactor, the change in density of the fuel with temperature must be known. This is especially important in a system utilizing molten fuel, such as LAMPRE (Los Alamos Molten Plutonium Reactor Experiment), since a relatively large change in density usually occurs during the solid-liquid transition. The fuel for LAMPRE is a Pu-2.5 wt pct Fe alloy with a melting temperature of 410°C. However, limitations in reactor design with this fuel have led to consideration of other plutonium-containing alloys for use in future generations of this type of reactor. Several ternary alloys containing plutonium and cerium as two components have satisfactorily low melting points. The system that at the present time appears to be most acceptable is Pu-Ce-Co; it exhibits little change in melting temperature with wide variation in plutonium concentration. Other alloys that have received some consideration contain nickel, copper, and manganese as the third constituent. The proposed fuel alloys are difficult to handle experimentally in the 25" to 800°C temperature range since they oxidize readily, react with many solvents, and contain a poisonous fissionable material. In addition, in this temperature range the alloys pass through the solid-liquid transition. Several techniques are available for measuring the densities and volume coefficients of expansion of solids or liquids. However, the only apparatus that appears suitable for measuring expansion coefficients over this temperature range and through the phase transition is a volumeter. In a volumeter, the indicating medium must be essentially inert to and insoluble in the material being studied. It must also possess a low vapor pressure over the operating temperature range, and its coefficient of expansion must be accurately known. One material that is satisfactory in nearly all of these respects is the alloy Na-78 wt pct K, which melts at -10°C and has a vapor pressure of 860 mm Hg at 800°C. This relatively high vapor pressure at 800°C requires an overpressure of an inert gas to prevent boiling. While a volumeter is capable of determining accurately the volume coefficients of expansion of materials, it cannot be used for absolute density measurements. Therefore, a density determination at a known temperature must be coupled with the volumeter measurements to give all the desired data. The weight-loss technique using immersion in bromobenzene at room temperature proved to be satisfactory. The preliminary work that was done on this experimental program involved developing and calibrating the equipment, and measuring the densities and volume coefficients of expansion of cerium and some low-melting binary cerium alloys. The complications that are caused with the introduction of plutonium into the system were avoided until the equipment was proved to be satisfactory and until experience was gained in its operation. It is this first phase of the experimental work that is described in this report. DESCRIPTION OF EQUIPMENT AND OPERATING PROCEDURE The NaK volumeter is shown schematically in Fig. 1. Basically, the equipment consists of two weld-sealed stainless-steel containers of nearly identical volume. One container holds a tantalum crucible and the specimen being measured; the other contains a tantalum crucible and a tantalum specimen used as a control reference material. To avoid temperature gradients, the bombs are located in a copper block inside the furnace. Stainless-steel capillaries of equal length and volume connect each stainless-steel container to a glass viewing capillary. The stainless-steel containers, stainless-steel capillaries, and a portion of the glass capillaries are filled with NaK (22 wt pct Na-78 wt pct K). The NaK/gas interface in the glass capillary is viewed with a cathetometer which is accurate to *0.5 mm. The cathetometer readings are used to calculate the volume changes of the samples during a run. This volumeter is basically the same as that described by F. Knight in Plutonium 1960. 2 However, changes in equipment design and operating procedure were made to eliminate some major operating difficulties. These changes are summarized below. 1) In filling the manometer with NaK, gas was frequently entrained in the system. Evacuation of the system before filling failed to eliminate the en-

Jan 1, 1965

By Robert T. Ault

The nature of fracture in unnotched tensile and notched tensile sheet and round specimens and V -notched and precracked Charpy-type sheet specimens of both wrought stress -relieved and re-crystallized molybdenum was investigated over the temperature range of -78° to 300°C. The sharp rise in fracture stress, for unnotched tensile samples, as the temperature is increased above the brittleness transition temperature (Tb), is found to be a result of an increase in flow stress due to plastic constraint and an increased strain rate which results from the onset of necking at Tb . Quasi-brittle fracture in notched tensile samples is found to occur when the tensile stress at the elastic-plastic interface, beneath the root of the notch, reaches a maximum critical value, which is independent of test temperature over the range from —78° to 25°C, but dependent on microstructure. In the temperature range between 150° and 300°C, unnotched tensile and notched tensile samples alike are found to fracture by a ductile fibrous tearing process which is discontinuous in nature, as a result of the competition between the processes of tearing, through continued plastic flow, and local work hardening. Results from the V-notched and fatigue-cracked Charpy-type impact tests demonstrate that crack initiation is the governing factor in the low-temperature (-78° to 25°C) fracture process for molybdenum. In recent years, there has been considerable interest, and a commensurate number of investigations, concerning the duc tile-to-brittle transition in refractory metals. There has not developed, however, a satisfactory explanation for the uniaxial tensile fracture-stress transition which accompanies the well-known ductility transition. This matter therefore warranted investigation. In a similar manner, the increased importance of notched tensile strength values in evaluating materials and in design criteria requires a better understanding of the factors which control the fracture behavior of notched tensile samples. In a previous investigation1 of the nature of initial yielding and fracture in notched sheet molybdenum at room temperature, it was suggested that plastic constraint was the controlling factor in governing the fracture behavior of notched samples. The final portion of this investigation was concerned with the fracture toughness of molybdenum. Of particular interest was the comparison of effective surface energies for fracture in V-notched samples with fatigue-cracked, Charpy-type samples in order to ascertain the relative importance of the initiation and propagation phases of the fracture process. MATERIALS AND TEST PROCEDURE Sheet tensile, notched tensile, and V-notched Charpy specimens were prepared from 50-mil, stress-relieved molybdenum sheet.* Half of these specimens were vacuum-annealed for 1 hr at 1200°C and 7.5 x l0-5 Torr and furnace-cooled to produce a relatively uniform grain size of 0.30 mm diameter. Round notched and unnotched tensile specimens were prepared from warm-rolled and swaged 5/8-in.-diam bar.* These specimens were vacuum-annealed for 1 hr at 1350°C and 5 x lom5 Torr and furnace-cooled to produce a grain diameter of 0.11 mm. Material analyses in ppm were: C N O H Sheet 290 10 4 1 Bar 50 30 30 2 The unnotched tensile sheet specimens had a 1/4-in. gage width and a 1-in. gage length. The unnotched tensile round specimens had a 9/32-in. gage diameter and a 1-1/4-in. gage length. The sheet and round notch tensile specimens are shown in Fig. 1. All of the notched tensile specimens tested were tandem-notched in order to study the location and mode of fracture initiation. The tandem-notched specimens were carefully machined so that the largest variation in notch depth on a single specimen was 0.001 in. Thus, when fracture occurs, the extent of plastic deformation that exists in the un-fractured notch section is that which exists just prior to fracture. All of the tandem-notched sheet specimens were electrolytic ally polished and chemically etched prior to testing. The V-notched Charpy-type specimens machined from the 50-mil sheet material had the standard dimensions of 2.125 in. long, 0.394 in. deep, and a 0.010-in. root radius. The unnotched tensile and notched tensile tests were conducted over the temperature range of -78° to 300°C, in a 10,000-lb Instron Universal Testing Machine, at a constant crosshead speed of 0.020 in. per min. The V-notched Charpy-type

Jan 1, 1964

By W. O. Philbrook, R. H. Spitzer, F. S. Manning

A generalized mathematical model has been developed to describe the kinetics of gas-solid reactions with special attention given to the hydrogen reduction oj dense spheres of hematite. This reduction process must pvoceed through a sequence of transport and chemical .reaction steps acting in series. Under typical experimental conditions, none oj the individual transport and reaction resistances may be neglected in the development of a physically significant model. A linear vate of thickening oj the product layer, usually taken as evidence of interface-controlled .reuction, may be observed even though transport resistances play a dominant role in the over-all kinetics. The temperature and pressure dependencies of all terms have been carefully evaluated in order to .make fill use oj arailable expe-inzental data in evaluation oj the model. FOR obvious technological reasons, the kinetics of reduction of iron oxides has become the subject of intensive experimental and theoretical investigation during recent years. Continuing efforts to construct mathematical models to describe the kinetics of reaction between a gas stream and a granular bed of solid particles have demonstrated the necessity of a thorough understanding of the reaction kinetics of a single particle within the system as a prerequisite to the construction of physically significant models of complex, reacting systems. This paper presents a critical examination of the transport and chemical-reaction processes involved in single-particle oxide reduction and develops the mathematical expressions necessary to evaluate their importance. Comparison of theoretical predictions with experimental results contributes important new understanding of the complex nature of this process. The reduction process has been studied under a wide range of experimental variables, and it is not surprising that apparent conflicts in observation and interpretation appear in the literature. The interested reader is referred to the reviews of Themelis and auvin"? and Manning and philbrook3 for a description of much of this work. The course of reaction commonly has been followed by measuring the oxygen weight loss from the particle as a function of time. A number of authors have suc- cessfully correlated their data in terms of a model which assumes that the reduction process is controlled by the rate of reaction at a single, sharply defined, advancing interface. According to this model, the interface will advance linearly with time. A mathematical model for gaseous reduction in a packed bed developed by the present authors in an earlier paper4 recognized that reduction must proceed through the series hematite (Fe203), magnetite (Fe30,), wiistite (Fe,O), and finally metallic iron. The reduction scheme permitted a stepwise topochemical reduction of the individual particles to metal or to the lowest oxide thermodynamically possible for the local gas composition in the bed. The limiting situations of theoretically dense and very porous oxide structures were considered. On the basis of available experimental evidence, the simplifying assumption was made in each case that all product layers would thicken linearly with time. A generalized single-particle model has now been developed to determine the significance of transport resistances in the product layers and in the gas film surrounding the particle. The analysis shows that the interplay of transport and chemical resistances is such that an apparently linearly advancing interface may be observed despite the fact that the reaction may be under significant transport control. Attention thus far has been focused on the development of a model for the topochemical behavior of dense spheres of hematite in atmospheres capable of reducing them completely to metal. The formation of successive product layers of iron, Fe,O, and Fe304 is assumed to follow the mechanism originally described by dstrijm.' All oxygen removal from the core occurs at the iron/Fe,O interface, intermediate oxide layers being propagated by sol id-state diffusion without change in the oxygen density of the core. Since fractional reduction is operationally defined in terms of oxygen weight loss, the kinetics of the over-all reduction of FeZ03 to iron is properly studied in terms of the gas-solid reaction occurring at the iron-wiistite interface. The fractional reduction of a partially reduced oxide sphere is given by: here refers to the radial position of the iron/Fe,O interface. This model is not universally applicable because, as explained in the earlier paper,4 a consideration of porous particles or of dense particles in atmospheres not capable of reducing wiistite must allow for the possibility of gaseous reduction at interfaces other than the one between iron and Fe,O. However, evidence that certain hematite specimens actually do follow the dense-pellet mechanism developed here is provided by the data of cewan' and of Bogdandy and

Jan 1, 1967

By AIME AIME

PLANS for the Semi-centennial Meeting have almost reached completion, although in any undertaking of such magnitude a few changes are always to be expected at the last moment. As worked out up to the time of going to press, the program of the meeting is shown below. The headquarters will be the Irem Temple, in Wilkes-Barre.

Jan 1, 1921

Lawrence Addicks, Perth Amboy, N. J. (communication to the Secretary*): The excellent series of photo-micrographs given in this paper shows clearly the relation between micro-structure and cuprous oxide in refined copper. The authors suggest that this method of examillation might be substituted for the " button " method now used to control the refining of cop

Jan 1, 1904

By AIME AIME

MIING Engineer. Metallurgist, Economist-in any of those three capacities Paul Tyler should be able to make a living. Further- more, he has proved his ability as an operating man teacher, researcher. and prolific writer. For the last three years he has been chief engineer of the non-metal Economics Division of the. U. S. Bureau of Mines.

Jan 1, 1941

By A. W. Ashbrook

There are essentially three main classifications for extractants: acidic, basic, and neutral. The acidic and basic are also referred to as cationic and anionic, respectively. Some extractants are shown in Table 11-1. Acidic Extractants Acidic extractants which are of use, because of cost and/or insolubility in water, are alkylphosphoric, sulphonic, aliphatic monocarboxylic acids and naphthalene derivatives.

Jan 1, 1978

California Oil and Gas Association, 510 West Sixth St , Los Angeles, Calif Edwin Higgins, Secretary This Association for many years published the monthly magazine, "Oil Bulletin " Publication was discontinued in June, 1932, and numbers are now available only in reference form Some of the articles in the magazine dealt with the geology and natural resources of gas and oil

Jan 1, 1933

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) The following members have registered recently at the Headquarters of the Institute Seeley W. Mudd, Los Angeles, Cal. Charles Janin, San Francisco, Cal. Edgar Rickard, London, England. Donnel F. Hewett, Washington, D. C. L. Maurice Cockerell, Chihuahua, Mexico.

Jan 4, 1913

The information in Tables 1 and 2, on the operations in the Dutch East Indies and North Borneo, has been kindly furnished to the Institute through the courtesy of Mr. J. August Kessler by Mr. B. H. van der Linden. It affords a very good picture of the situation in that region for the year 1933.

Jan 1, 1934

Section 67 Department of Conservation and Development, State of New Jersey, State House Annex, Trenton, N. J. H B Kummel, State Geologist For lists of publications, maps and geologic folios, address the above. Where price of postage is noted, in the following list of available publications on geology, the postage is only to New Jersey and

Jan 1, 1933

SALT LAKE CITY MEETING The One Hundred and Eighth Meeting of the Institute, for the presentation and discussion of technical papers, will be held at Salt Lake City, Utah, August 10 to 14, 1914. ALL PAPERS TO BE PRESENTED AT THIS MEETING MUST BE IN THE HANDS OF THE SECRETARY ON OR BEFORE MAY 31, 1914.

Jan 3, 1914

By R. M. Schuster, F. M. Benavides

This study compares the costs of transporting coarse coal by pipeline versus more conventional belt conveyors. Hydraulic conveying of crushed (not pulverized) coal has not had widespread commercial acceptance. However, there is little doubt that the technology is available, so that, should this method be proven economical for a given application, implementation will become more acceptable.

Jan 1, 1984

By S. S. Arentz

An organized safety program has reduced accidents at Pioche because effort is first devoted to arousing and maintaining interest in safety, followed by training in accident prevention, assigning responsibility for the detection and removal of safety hazards, and finally, by keeping score through an adequate system of records. A health program is intergrated with the safety program.

Jan 2, 1950