Search Documents

By R. O. Williams

The concept of biaxial pole figures which completely represent sheel textures is defined and an iterative least-squares solution given. The method has been applied to rolled copper, aluminum, and brass. The results show that the prior ideal textures are reasonably correct but incomplete. The major components in all three cases consist of a continuous range of orienta-tions roughly described as starting from (211) [111] continuing to (110) [112] to (110) [001], the details dif- THIS paper considers the problem of representing rolling textures in the most useful and comprehensible manner possible. A representation called a biaxial pole figure which completely represents such textures fering in all cases. For brass, in particular, the last part of the range is the most important. A minor cube component is established for the copper and aluminurn. The results were also analyzed by means of sets of three axial (inverse) pole figures to give similar, less-detailed results. The method of analysis is outlined. Such a representation is significantly less powerful than the biaxial method, but it has considerable utility in the calculation of anisotropic properties. is defined and an iterative least-squares solution is given. Such textures may be approximated by treating the principal directions as fiber axes to give three axial (inverse) pole figures. This representation is very useful for calculating anisotropic properties. New data for rolled copper, brass, and aluminum are given by both methods. In an axial pole figure the relative frequency or probability of a given physical direction (normally the

Jan 1, 1969

By R. J. Wasilewski

The resistivity of single crystal and of polycrystalline metal has been determined between 77° and 1500°K. At comparable purity, the resistivity of the poly crystalline metal differs from that calculated from the axial resistivity values. The observed anisotropy is briefly discussed. A zone refined titanium rod was obtained from F. J. Darnell.1 The hardness of this material varied between 52 and 64 Bhn, indicative of its high purity. Single-crystal specimens were cut out from a few large grains, elongated predominantly along <1120>. Resistance measurements were taken with specimens immersed in liquid nitrogen, solid CO,, and acetone, and at ice point, and then recorded continuously between room temperature and 1200" to 1250°C, throughout at least one full heating and cooling cycle at a rate of l° to 3°C per min. Four probe measurements were taken using spot-welded Pt wire 0.003 in. in diam as potential terminals, and the electromotive force drop was determined poten-tiometrically. A standard resistance, in series with the specimen, served to determine the dc current (generally about 80 ma) in the circuit. In order to eliminate spurious thermal electromotive forces, the circuit polarity was automatically reversed at 5-min intervals, and the mean of the two adjacent readings taken as the true electromotive force value. The discrepancy between the readings at reversed polarities was generally of the order of a few µ v, as all the spot-welded joints were contained within a volume of some 5 mm cube. The relative resistance (R T/R 273o) variation with temperature is tabulated below, and shown in Fig. 1, as measured during the first heating run. The discontinuous drop in resistance, corresponding to the a — ß transformation, started for both initial orientations at 1170°K; i.e., some 15°K above the accepted value of 882°C (1155°K). Judging by the temperature ranse of transformation—some 30°K for the single crystal and 20°K for the polycrystal-line specimen—this difference is believed caused by the solution of the oxygen present initially on the surface of the specimens. The general trend of the resistance vs temperature shown in Fi,;. 1 is in qualitative agreement with that previously reported for polycrystalline titanium metal. 2,3 Significant anisotropy is, however, indicated by the crossing over of the curves for <1120> and <0001> orientations at 273°, 650°, and 1000°K. This difference is most startlingly shown in Fig. 2, where instantaneous temperature coefficients (l/R273 x dR /dT) are plotted for both the first heat-

Jan 1, 1962

By V. C. Perini

The 1943 designation of districts for the Transactions† has caused some confusion because of the elimination of the West Central Texas district and the allocation of the counties of this district to the North Texas district and the North Central Texas district. The North Central Texas district as herein defined includes the counties of Brown, Callahan, Cole-man, Comanche, Coryell, Eastland, Erath, Fisher, Hamilton, Hood, Jones, Lampasas, Mills, Nolan, Palo Pinto, Parker, San Saba, Shackelford, Stephens, Stonewall, Summerville, Taylor, Throckmorton and Wise. These counties as listed are the counties of District 7B, State Railroad Commission. This district covers the south central crest and the west flank of the Bend flexure north of the Llano uplift. The west flank of the Bend flexure is on the east boundary of the Permian Basin of West Texas. The North Texas district, District No. 9, State Railroad Commission, includes the counties of Archer, Clay, Cooke, Foard, Hardeman, Jack, Knox, Montague, Wichita, Wilbarger and Young. The area of this district covers the crest and south flank of the Red River uplift and the north central crest of the Bend flexure. The greater part of the oil and gas produced in the past from the North Central Texas district has been from Pennsyl-vanian strata. Some oil and gas has been produced from the lower Permian (by the latest selection of the Pennsylvanian-Permian boundary&apos;) and minor amounts from the Mississippian and Ordovician sediments. Increasingly important quantities of oil and gas are to be expected from the older sediments by deeper development in proven fields and by new discoveries. Most of the oil and gas in the district has accumulated in localized, well-defined structural traps in limestone and sandstone reservoirs and in traps due to stratigraphic changes in sedimentation, mainly porosity traps in limestone and sandstone lenses, both usually associated with some structural feature. The Stripper Well Premium Plan as adopted by the office of the Federal Price Administrator has been an aid to the producers of stripper wells. The producers are pleased to receive the subsidy to prolong the plugging of wells, but they are not too pleased with the subsidy plan in principle. Most independent operators are in favor of, and think they are entitled to, an increase in the market price for oil. The price is not adequate to meet the requirements of the average independent operator with the continued advance in production, development and wildcatting costs. Old and new pipe lines for oil and gas leading out of the state are removing reserves at an alarming rate. Curves showing the rate of discovery versus production and pipe-line deliveries in and out of the state make a cross that sooner or later will be fatal to the state. Wildcatting not only needs a price increase but every other available incentive and encouragement.

Jan 1, 1945

By LeRoy Scharon

EACH year it becomes apparent that geophysical activities in the fields of mining and engineering are increasing in the number and variety of applications. Many mining companies are including, as part of their exploration programs, geophysical surveys. The value of geophysics in highway and structural foundation investigations has been realized and is now an important part of subsurface investigations in conjunction with soil and rock borings. United States of America One of the major orebody discoveries of the year is that of the Grace mine near Morgantown in Berks County, Pa. This orebody, now under development by the Bethlehem Steel Co., was discovered by an airborne magnetometer survey carried out by the Aero Service Corp. of Philadelphia. The orebody, the geological occurrence of which is similar to those existing at Cornwall, Pa., was found at a depth of 1500 ft under a cover of Triassic sediments and is reported to have a reserve of well over 100 million tons. Shaft sinking and other construction work has started at the site. Resistivity work was carried out at proposed dam sites in New York and in connection with the search for fluorspar veins in Kentucky. Spontaneous polarization investigations were pursued in the Appalachian region at various localities from North Caro¬lina up into Virginia. This work was done in connection with the search for sulphide-bearing structures. Several indications were proven by subsequent drilling to correspond to unknown sulphide deposits, a few of these occurring in the vicinity of properties long under exploitation. Refraction seismic methods applied to bedrock depth determinations as related to water problems on the Marquette Range and the extension of the. regional gravity survey on the Menominee Range to learn the major structural features of the area have been reported by, Lloyal O. Bacon. A gravity survey has been completed in the vicinity of Tioga, Bradford County, Pa. with a gravity profile being observed from Tioga east to the Delaware basin. The Indiana Geological Survey is concerned with a state-wide gravity survey. Judson Mead, University of Indiana, reports that the bulk of the State Survey&apos;s geophysical work, however, has been "seismic refraction work in connection with drift thickness problems. The survey has made almost 1000 determinations in areas of moderately thick drift. The results of this work are of interest to both the coal mining industry and to the stone industry." In the southeastern Missouri lead belt, magnetic electrical resistivity, and electromagnetic applications for the discovery of new lead deposits have been used with success. A gravity survey of the residual-barite deposits in Washington County, Mo., was made during the summer season with preliminary computations of tonnages checking with tonnages mined. Robert M. Dryer, of the University of Kansas has had considerable success in mapping structural features in southwestern Kansas with the gravity meter and is now engaged in tracing shoestring sands in eastern Kansas by resistivity surveys. Several, foundation sites were investigated in greater St. Louis using electrical resistivity and seismic refraction methods with success. A minimum amount of drilling data was available for checking and interpreting the geophysical results (Fig. 1). It is to be noted that geophysical methods are finding a place in subsurface investigations for highway and foundation problems. Interest has been so keen in this field that the American Society for Testing Materials, at its annual meeting in June of this year, devoted one session of its symposium on surface and subsurface reconnaissance to geophysical papers involving the application of the electrical resistivity and seismic refraction methods to subsurface studies. At least three major mining companies in the United States have entered the field recently in geochemistry. The program of research and development of geochemical techniques by the U. S. Geological Survey continues. Experimental field projects were conducted over lead-silver, cobalt, copper and zinc deposits in Idaho, Oregon, California, Wisconsin and Montana. Similar experiments were carried on by M. P. Nackowski in the Illinois-Kentucky fluorspar district and in the Tri-State Zinc district by R. Maurice Tripp with favorable results. Geophysical activities of the U. S. Geological Survey for 1951 were extensive and varied. About 21,000 miles of airborne magnetic and 10,000 miles of airborne radioactivity traverse were flown in 1951 by the U. S. Geological Survey. A total of 35,000 miles of aeromagnetic traverse were compiled, 57 aeromagnetic maps were published and 14 preliminary maps were placed on open file. Airborne surveys were made in Aroostook County, in the Katahdin and Dead River areas in Maine; in northwest Washington; over the Mother Lode district in California; in northeastern and northwestern Minnesota; and in the New York-New Jersey highlands. Of special interest were the surveys in Washington, where highly magnetic Eocene lavas gave information on structures in the overlying Miocene sedimentary rocks and in northeastern Minnesota over the Duluth gabbro. The latter survey was made following the discovery of nickel-copper mineralization in the gabbro near its contact with the Virginia slate. The principal ground geophysical surveys for metalliferous deposits and related purposes were made in the Colorado Plateau region, where electrical surveys assisted in prospecting; in Aroostook County, Maine, where ground magnetic surveys, following aeromagnetic surveys, have permitted tracing

Jan 1, 1952

By K. S. Seljesater

Since the development of dispersion-hardenable lead-antimony alloys&apos; in the laboratories of the Western Electric Co., Inc., studies have been made of the effect of various third constituents on these alloys.2 This paper covers a study of the effect of small amounts of arsenic. This element is important since it occurs as an impurity in many commercial antimonial leads and the results obtained are particularly interesting as indicating a class of addition agents which exert a stabilizing effect on dispersion-hardened alloys. Experimental In order to study the effect of increasing amounts of arsenic, a series of alloys were made up containing 1 per cent. antimony, and arsenic varying from 0. to 0.10 per cent., the balance Doe Run lead (99.997 per cent. lead). The alloys were cast into bars 1 1/2 in. wide by 3/4 in. thick and cold-rolled to about 1/8 in- thickness. Three samples of each composition were annealed 1 hr. at 225" C. and quenched in water. One set was aged at room temperature, one at 50" C., and the third at 100" C., the

Jan 1, 1929

By K. S. Seljesater

Since the development of dispersion-hardenable lead-antimony alloys&apos; in the laboratories of the Western Electric Co., Inc., studies have been made of the effect of various third constituents on these alloys.2 This paper covers a study of the effect of small amounts of arsenic. This element is important since it occurs as an impurity in many commercial antimonial leads and the results obtained are particularly interesting as indicating a class of addition agents which exert a stabilizing effect on dispersion-hardened alloys. Experimental In order to study the effect of increasing amounts of arsenic, a series of alloys were made up containing 1 per cent. antimony, and arsenic varying from 0. to 0.10 per cent., the balance Doe Run lead (99.997 per cent. lead). The alloys were cast into bars 1 1/2 in. wide by 3/4 in. thick and cold-rolled to about 1/8 in- thickness. Three samples of each composition were annealed 1 hr. at 225" C. and quenched in water. One set was aged at room temperature, one at 50" C., and the third at 100" C., the

Jan 1, 1929

By J. Warner, M. J. Marcinkowski, B. Cullen, T. Prevender, J. Mcllwain, T. Carnahan, J. Pahlman, J. Demel, J. Munford

The following analysis was an outgrowth of a midterm examination given by one of the authors (M.J.M) in a course entitled Metallurgy 541 "Applications of Dislocation Theory&apos;&apos; at Iowa State University. Fig, l(a) shows the three-layer sequence of atoms lying in the (111) plane which characterizes the fully ordered AB3 fcc crystal, i.e., LI2 type. If any two-layer sequence of close-packed planes is constructed from Fig. 16)&apos; the structure would be hcp of the DO,, type. Consider for convenience that the circled atoms lie in the plane of the drawing while those shown square and triangular lie immediately above and below the plane of the drawing, respectively. It has already been shown&apos; that if a Shockley partial dislocation is passed over the plane of the paper, then the square atoms in Fig. 1(a) are displaced from their original positions as shown by the arrows in Fig. l(b). Not only is an intrinsic fault produced but the crystal is simultaneously disordered across the slip plane. In particular, 2AB bonds are converted to 1AA and 1BB bonds when referred to the area outlined by the solid line in Fig. 1. If, on the other hand, a Shockley partial is allowed to pass immediately above and immediately below the plane of the paper so as to displace the atoms in opposite directions as shown in Fig. l(c), an extrinsic fault is producedZ and twice the amount of disorder is introduced into the crystal as compared to the dislocation-produced intrinsic fault, if only broken first-neighbor bonds are counted. If an intrinsic stacking fault is produced by removing a close-packed plane of atoms in Fig. l(a) and displacing the two adjacent planes by 1/3a0[111], no wrong nearest-neighbor bonds are produced. Similarly, if an extra half plane of atoms with the same arrangement as any of those shown in Fig. l(a) is inserted between any two planes in the same figure, then an extrinsic stacking fault is produced in which once again no wrong nearest-neighbor bonds are produced. The latter two faults are bounded by Frank partial dislocations. Since, at least in the alloy CU3AU,3 nearly all of the ordering energy resides in the first nearest-neighbor interactions, intrinsic and extrinsic stacking faults and associated APB&apos;s of the Frank type are expected to have significantly lower energy than those of the Shockley type in CusAu in particular and quite likely in L1, and DO19 type alloys in general. Also, because of the higher degree of disorder plus loop interaction

Jan 1, 1968

By Lennart Wellenius

LAISVALL - ONE OF THE BOLIDEN MINES Until the Aitik Mine (2,000,000 mtpy) started in 1968 the Laisvall Mine (1,200,000 mtpy) was the biggest unit of about 20 producing mines, belonging to the Boliden Company Ltd. As shown in Fig. 1 the mines are spread over a wide area. Most of them are small complex ore mines (50,000 - 300,000 mtpy), for which reason the total mine production does not exceed 5,500,000 mtpy. When our company was invited to present a paper, Laisvall was chosen because it is the biggest European galena-mine in production today. The Laisvall Mine is situated in the county of Norrbotten, Sweden, at the eastern border of the Caledonian mountain-chain. The road distance to Slagnäs, the nearest railway station, is 60 miles. The railway between Slagnäs and BOLIDEN&apos;s smelting plant, the Rönnskär Works, is 140 miles long. PRODUCTION STARTED IN 1943 In the Autumn of 1938 a boulder was discovered, consisting of sandstone with galena, on the shore of the Lake Stor-Laisan. The boulder came from an Eocambrian sandstone formation, which is overlain by Cambrian-Silurian rock.

Jan 1, 1970

By C. Wagner

When an alloy solidifies and the composition of the solid differs from the composition of the liquid, atoms of the alloying elements rejected at the solid-liquid interface have to diffuse toward the bulk liquid. Diffusion may be supported by convection. Theoretical calculations have been made for a liquid without convection, for a liquid involving natural convection, and for solidification of a liquid alloy at the surface of a rotating disk as an example of forced convection. WHEN an alloy solidifies, the equilibrium composition of the originating solid phase differs in general from the composition of the liquid phase. Thus, segregation may take place, i.e., the composition of the solid phase formed at different times differs from the bulk composition. The degree of segregation depends on several factors such as the partition ratio of the alloying elements between the liquid and the solid phase, the rate of solidification, and convection. To clarify, a theoretical analysis has been worked out. The following presuppositions are made: 1—Calculations are confined to the solidification of binary alloys in which the concentration of component A (solvent) is much greater than that of component B (solute). 2—The equilibrium concentration of the alloying element B is assumed to be lower in the solid phase than in the coexisting liquid phase. 3—At the solid-liquid interface, partition equilibrium is assumed. 4—The dependence of the partition ratio of the solute between the liquid and the solid phase on concentration and temperature is disregarded since only small concentrations of the solute are considered. 5—The concentration of the alloying element B in the solid phase is supposed to be lower than the saturation concentration for the formation of a second solid phase. 6—diffusion in the solid phase is disregarded, since diffusion rates in the solid state are comparatively low. When the partition ratio of the solute between the liquid and the solid phase is greater than unity, a part of the solute is rejected at the solid-liquid inter- face and has to diffuse toward the bulk liquid. Thus there is necessarily a concentration difference in the liquid between the solid-liquid interface and the bulk liquid as has been pointed out by Hayes and Chipman,&apos; Rutter and Chalmers,&apos; Tiller, Jackson, Rutter, and Chalmers, and others (see Fig. 1). In view of the concentration gradient in the liquid phase, the ratio of the concentration of the solute in the solid phase to that in the bulk liquid differs from the equilibrium ratio, although at the solid-liquid interface, partition equilibrium is assumed. Under certain limiting conditions, the solid may even have virtually the composition of the bulk liquid as is shown below. General Equations Let u be the linear crystallization velocity in cm per sec, D the diffusion coefficient of component B in the liquid phase in cm2 sec-&apos;, c&apos;,, and c", the concentrations of component B in the liquid and the solid phase, respectively, in mol per cm", and s the distance from the solid-liquid interface toward the bulk liquid at a given time t. The partition ratio is assumed to be equal to a partition constant K. Thus. The difference in the specific volume between the liquid and the solid phase may be disregarded. In view of the discontinuity of the concentration of the solute at the interface according to Eq. 1, u(c&apos;, — c",), , , = tic&apos;, (S = 0)(1 — K) gram-atoms B per unit area per unit time are rejected at the interface and have to diffuse toward the bulk liquid. From Fick&apos;s first law it follows that uc&apos;,,(s = 0) (1 ~K) == - D(dc&apos;,,/?>s). _-„. [2] The concentration profile in the liquid near the interface depends on the interplay of diffusion and convection as is discussed in the following sections. A schematic concentration profile is shown in Fig. 1. The "effective thickness of the diffusion boundary

Jan 1, 1955

By F. N. Ward, E. H. Bailey

Camp and sample-site methods useful for determining about 0.5 to 16 ppm of mercury in soils and rocks have been devised to complement the analytical methods already widely used in geochemical prospecting. In the camp-site procedure the sample solution is obtained by digesting the finely powdered sample with hot nine-molar sulfuric acid and bromine, the latter generated in place. The solution is buffered at a pH of 4 and the mercury is extracted into a relatively small volume of an organic solvent. Estimations are made by comparing the color of the mercuric dithizonate extracted from the sample with that extracted from a standard. In the sample-site method the mercury is volatilized as the iodide and the latter is dissolved in a buffer solution from which the mercury dithizonate is extracted as in the camp-site method. The estimation is made by a similar comparison with standards or by comparing the color of the mercuric dithizonate with artificial standards prepared from Orange II, an azo dye. Except for the establishment of standards, the time required by an experienced analyst seldom exceeds 10 min for a camp-site determination and 5 min for a sample-site determination. Camp-site determinations are useful for commodity studies and intensive exploration programs; sample-site determinations are applicable to extensive and reconnaissance-type geochemical prospecting programs. The results obtained on samples taken along traverses above known mercury ore deposits in the California Coast Range and western Nevada demonstrate the usefulness of both methods in geochemical prospecting. The increasing use of the mercury content of soils, rocks, plants, or water in geochemical prospecting emphasizes the need for analytical methods which are sensitive and at the same time require a minimum of readily available equipment. Sensitive methods based on the absorption of ultraviolet light by mercury vapor are common in the literature31 12. Although none of these methods have been used to analyze the large number of samples required in geochemical prospecting, they could be extremely useful except for the expensive instrumentation usually required to make the methods quantitative Also, such methods are perhaps too sensitive for field use, especially around areas of possible contamination. Other methods involve the distillation of mercury from a relatively large sample and subsequent collection of the vapors in nitric acid6. The mercury is then estimated by titration with a suitable reagent such as thiocyanate. These methods are not trace methods because the actual amount of mercury measured is often as great as 50 to 100 milligrams. Also, such methods are unsuitable for geochemical prospecting because of the amount of equipment necessary and the time required. Still other methods involve colorimetry, and the sensitive reaction between dithizone and mercury (11).. is the basis for a number of reports on the determination of mercury in biological materials 5,7. Moreover, by the judicious use of solvent extraction and suitable complexing agents, the dithiaone method can be made almost specific for mercury. However, none of the dithizone methods have yet been applied to the determination of mercury in soils and rocks. In most colorimetric methods he sample solution

Jan 1, 1961

By Fred W. Gordon

The North Chicago Rolling-Mill Co., of Chicago, have four furnaces at South Chicago, built during 1881. Each furnace is 20 feet diameter of bosh, and 75 feet total height, the hearth being 11 feet diameter, and the top 15 feet 4 inches. They are blown through seven 7-inch tuyeres placed 5 feet 6 inches above the hearth level. Cubical contents, 15,000 cubic feet. Each furnace is supplied with 2 blowing engines, 84-inch blowing cylinder, and 36-inch steam cylinder, and 54-inch stroke. These two have one jet-condenser worked by an auxiliary pump. The blast for each furnace is heated by the aid of three Whitwell fire-brick stoves, each 21 feet diameter and 60 feet high. In the batteries of boilers furnishing steam for four furnaces there are 36 double-length boilers, 76 feet long, 48 inches diameter and 16,000 square feet heating-surface. The plant was designed to produce 3600 tons per week, or 900 tons for each furnace, and was fitted as above with such engines, boilers, and hot-blast stoves as were thought requisite for that production ; hence, calculated from the present make—not the least remarkable feature is the economy of construction—there are less engines, less boilers, and less hot-blast power for the iron made than at ally plant within my knowledge, or it could to-day be duplicated for less money per ton of iron made per week than could any plant now in existence, whether using fire-brick or cast-iron stoves for heating the blast. This is a practical demonstration of my assertion in a paper on fire-brick stoves, read before the Institute," that the application of fire-brick stoves in construction really lessens the first cost. In view of the statements just made, I must be most emphatic in assuring the members that nothing is strained or overburdened.

Jan 1, 1886

By V. T. Stringfield, H. H. Cooper

ONE of the earliest investigations of ground water in Florida was made in 1513 when Ponce de Leon arrived at St. Augustine in search of the Fountain of Youth. The history of the development of the water resources of the State shows that the large artesian reservoir that underlies Florida was discovered in the latter part of the last century. Part of that history is given by L. C. Johnson&apos; who states that the first successful artesian well in Florida was drilled at St. Augustine between 1880 and 1882. After the City of Jacksonville failed to obtain a flow of artesian water at a depth of nearly 400 ft and abandoned the drilling, R. N. Ellis, City Engineer, and L. C. Johnson, using Johnson&apos;s knowledge of the geologic structure of the artesian reservoir, estimated correctly that artesian water could be obtained at a depth of about 500 ft. Thus began the development of the large artesian system in the northeastern part of the State. In 1908, the Florida Geological Survey issued its first report on the ground water of central Florida. More recent reports give the results of investigations that have been in progress in cooperation between the Florida Geological Survey and the U. S. Geological Survey since 1930. As a result, the ground-water geology and hydrology of Florida are now so well known that ground-water problems such as confronted early investigators no longer exist. However, new problems arise and new discoveries are made as the demand for more ground water increases with the development of the State. Water-Bearing Formations Descriptions of the geologic formations and a map showing their distribution at the surface are given in a recent report by Cooke.&apos; The geologic formations that yield the ground-water supplies in Florida represent only a small part (about 1000 ft) of the total thickness of the sedimentary rocks (more than 15,000 ft) that underlie Florida. The water-bearing rocks that yield fresh water include more than two dozen formations that range in age from Eocene to recent. The Eocene formations, which consist chiefly of limestone, are the oldest and the deepest of the formations in Florida that yield fresh water to wells. In 1944, on the basis of a study of the foraminifera, the Applins -ivided the limestone of Eocene age into six formations, which are as follows, from top to bottom: Age or group Formation Jackson Ocala limestone icAvon Park limestone Claiborne -j Tallahassee limestone aLake City limestone Wilcox Salt Mountain limestone xOldsmar limestone The Ocala limestone and the underlying formations of Claiborne age, along with some of the overlying limestone of Oligocene and Miocene age, constitute the principal source of water in Florida and southeastern Georgia and generally may be regarded as forming one artesian aquifer or water-bearing unit. This aquifer is referred to in this paper as the Floridan aquifer, a name proposed by Parker.&apos; In part of Seminole County alone more than 1000 flowing wells yield water from the Floridan aquifer. A yield of 6500 gpm, or about 9.5 million gal per day, by natural flow from a well penetrating the aquifer at Jacksonville, Florida, was observed in 1942. A yield of about 7000 gpm by natural flow was reported for a well 1390 ft deep at St. Augustine in 1887. The largest yield reported from a pumped well penetrating the aquifer is 7500 gpm, or about 10.5 million gal per day. The aquifer is also the source of some of the large springs, such as Silver Springs, whose discharge, according to measurements made by the U. S. Geological Survey, has ranged from 526 to 1350 sec-ft, or from 340 to 872 million gal per day. The top of the Ocala limestone, as represented by contours in Fig. 1, indicates in a general way the geologic structure of the formations that comprise the Floridan aquifer. The Ocala is at or near the surface in the areas represented by shading in the northwestern part of the peninsula and also in an area in western Florida adjacent to Alabama and

Jan 1, 1952

By John C. Smock

The ten years, 1879 to 1888, inclusive, have been notable in the history of iron-making for the great rise during the latter part of 1879 and the earlier half of 1880; for the maximum of production in 1882 ; for the gradual decline and the reduced product through 1883,1884 and nearly to the end of 1885; then, for the recovery through- 1886 and 1887; and the extraordinary outputs of our iron furnaces during the last three years. The price of pig-iron might be taken as an index to the condition of the iron-mining industry, and if represented graphically, they would shorn approximately parallel curves. The mining industry cannot always respond quickly to a rise in price and an increased demand for ore; nor can its production drop simultaneously with sudden falls in price of iron and of ore. Hence, the irregularities of the one are not reflected in the other. The statistics of the iron mines collected by the United States census, for the year ending June 30, 1880, exhibit admirably their condition at that time. The reports received from mine owners and managers, of the production for the year 1888, furnish the basis for a comparison and supply data for some notes on the changes in the iron-mining industry in New York which have taken place in this period of time. The iron-ores of New York may be grouped in the following districts: I. The Highlands of the Hudson (magnetites). II. The Lake Champlain and Adirondack Region (magnetites). III. St. Lawrence and Jefferson Counties (red hematites). IV. Clinton and Wayne Counties (fossil-ores of the Clinton Group). V. Dutchess and Colnmbia Counties (limonites). VI. The Hudson River (carbonates). VII. Staten Island (limonites). The ores of the first and second districts, as enumerated, are almost exclusively magnetites; those of the third and fourth are hematites;

Jan 1, 1889

By A. R. Kinkel

THE Shasta copper-zinc district of northern California lies in the foothills of the Klamath Mountains at the northern end of the Sacramento Valley. It contains two main areas of base-metal ore deposits, the East Shasta and West Shasta districts shown in Fig. 1. The East Shasta includes the area from the Afterthought mine, near the settlement of Ingot on U. S. highway 299 East, to the Bully Hill mine, on the north side of the Pit River, 9 miles to the northwest. The West Shasta, a well-defined northeast-trending district about 8 miles long and 2 miles wide, west of the Sacramento River, Fig. 2, is the western part of the ore-bearing area formerly known as the Shasta copper belt. Referred to in the older writings as a copper arc, this belt was thought to form a crescent extending entirely around the head of the Sacramento Valley, the convex side to the north. Recent studies by the U. S. Geological Survey in cooperation with the California State Division of Mines show that there are two districts, one at each end of the so-called copper arc, which are distinct in geologic structure and ore occurrences, and that there is only sporadic and unconnected copper mineralization between them. Ore deposits of the two districts are similar in mineralogy, that is, they are largely massive pyritic ores containing copper and zinc with minor amounts of gold and silver, but the structure and structural control of ore deposition are different. The ores of the East Shasta district are replacements of steeply dipping shear zones in Triassic rhyolite and shale, whereas those of the West Shasta district are replacements of gently dipping rhyolite of Middle Devonian age and are essentially flat-lying. Thus there is marked lateral control of orebodies by shear zones in the East Shasta district and equally marked vertical control of orebodies by the stratigraphy in the West Shasta district. Geologic Setting The Paleozoic rocks of the West Shasta district range in age from Middle Devonian (?) to Missis-sippian. The oldest formation exposed is the Copley greenstone, probably Middle Devonian. It is composed of volcanic flows, volcanic breccias, and tuffs, all of mafic composition, but contains minor amounts of shale and rhyolitic tuff. Largely submarine in origin, it rests upon a base of older marine sediments, as shown diagrammatically in Fig. 3. The lower part of the formation is made up principally of flows, many of which are ellipsoidal, and the upper part contains most of the pyroclastic material. The formation is at least 3700 ft thick. The Balaklala rhyolite overlying the Copley greenstone is made up of many rhyolitic flows and beds

Jan 1, 1956

By David Keys

THE actual procedure in estimating depth of overburden from mag-netic observations made on the surface will vary with the form of the deposit and any theoretical discussion will apply only so far as the form of the deposit conforms to the mathematical premises on which the theory is based. Since the shapes of natural deposits in the field cannot be expressed rigorously in mathematical form, the best that can be done is to assume some simple form and deduce results. Fortunately many small variations in form produce only slight changes in the estimated depth of overburden, therefore the methods have a definite practical value. For the theoretical treatment, magnetic ore deposits may be divided roughly into three classes, depending upon whether the magnetic anom-alies may be considered to arise from (1) a single magnetic pole, (2) a dike or (3) a magnetic doublet. Particular cases, falling under one or other of these classes, have been discussed by different authors.1-4 In general, it may be stated that when the magnetic effects as measured on the surface are due only to one pole of the body, the other pole being so remote that its effect may be neglected, the resultant anomaly F at any point will vary as the inverse square of the distance r of the point from the pole, which may be expressed mathematically by F = k/r2, where k is a constant. When the deposit occurs in the form of a long, thin dike, the resultant anomaly will be of the form F = k&apos;/r and when the deposit is in the shape of a lens, so that both poles have an appreciable effect on the surface, the result will be similar to that caused by a magnetic doublet, and the form will be F = k&apos;/r3. The particular class under which a deposit falls may be deduced from the results of the magnetic survey. The second class is readily found, but there may be difficulty in deciding between the first and third. Isody-namic contours of both the vertical and horizontal anomalies will often be a good guide in making a correct decision.

Jan 1, 1937

By W. R. Kube, W. H. Oppelt

Five low-rank coals, including two lignites, a steam-dried lignite, and two subbituminous coals, were carbonized at 940°F, in a bench-scale carbon-ize~ with a nitrogen and hydrogen atmosphere, or both, using pressures from atmospheric to 1000 psig. Coking characteristics were observed, and yields, composition, and distribution of products from thermal degradation were determined. The influence of pressure on yields from coal carbonization, as well as on modification of coke structure, has long been of interest. One of the first attempts at pressure carbonization was that of Capps and Hulett1 who in 1917 investigated the effects of pressure ranging from 1 to 20 atm on yields at 600° C for bituminous and subbituminous coals. High-pressure carbonization has not been used commercially for coke production. More recently, carbonization at relatively high pressure in the presence of catalysts and hydrogen has been proposed for the production of metallurgical-grade coke from low-rank fuels.&apos; Another approach involves carbonization at high pressure in a hydrogen atmosphere to produce heating gas and a solid residue that is gasified with oxygen and steam to produce the hydrogen required for hydro-genation 3-4 or, alternatively, is burned to raise steam. Recently it has been proposed to carbonize coal under pressure, burn the gas in a gas turbine to produce power, and use the solid residue as fuel in a conventional steam-power plant.5 Our primary interest in pressure carbonization stems from an attempt to determine the influence of pressure on the coking characteristics of lignite to design a high-pressure slagging gasifier using oxygen and steam. At atmospheric pressure, North Dakota lignite is generally considered to be non-coking. However, lignite and subbituminous coals have been reported to show increased agglomeration properties in steam, hydrogen, or carbon-dioxide atmospheres at elevated pressures, although no strong coke was formed at pressures up to 3000 psig.6 If lignite would agglomerate seriously under gasification conditions, proper flow of charge through the gasifier could not be maintained without installing a mechanical stirring device or destroying the caking properties of the coal before gasification. Data on the caking properties of lignite or other gasification fuel, as well as on yields of products under conditions simulating the carbonization process in the pregasification zone, were required in the preliminary design stage of the gasifier. No information was available concerning the influence of pressure and type of atmosphere on North Dakota lignite. To provide this basic data, the U. S. Bureau of Mines investigated the effect of pressure and a hydrogen or nitrogen-rich atmosphere on the yield of products and on coke formation in a bench-scale pressure carbon-izer. SCOPE OF INVESTIGATION Five coals were tested at 940°F in nitrogen and hydrogen atmospheres, at pressures from atmospheric to 1000 psig. Yields and composition of solid, liquid, and gaseous products were determined as a function of the process pressure, and attention was given to the physical appearance of the solid residue. Percentage of carbon converted, sulfur retained in char, and thermal balances were calculated. In this paper, primary consideration is given to carbonization in a nitrogen atmosphere and to data concerning the solid phase. The effect of pressure in hydrogen is presented in detail for only one lignite. More complete information on the response of the other coals in a hydrogen atmosphere will be published in a USBM Report of Investigations. DESCRIPTION OF EQUIPMENT Details of the bench-scale pressure carbonizer are given in Fig. 1. The body of the carbonizer was

Jan 1, 1961

By H. A. Tobelmann

age Introduction ............................. 22 Crushing............................... 25 Leaching............................... 28 .Reduction.............................. 47 Electrolytic Deposition..............a.......... 51 Discard for Purification of Electrolyte.................. 60 Recovery of Copper from Discard Solution .............. 62 Resolution of Cement Copper...................... 64 Summary............................... 64 Appendix............................... 66 Discussion............................... 69 Introduction The location, mode of occurrence of ore, and preliminary tests leading to the development of the present leaching process and the building of the present plant on the property of the New Cornelia Copper Co. at Ajo, have been described in previous papers presented to the Institute and in the discussions thereof.l It is sufficient to say that these tests began early in July, 1912, and were continued to the close of January, 1916; that small tests at Douglas were followed by the construction of a 1-ton plant at the mine; and this was followed by the operation of a 40-ton plant for 11 mo. In all about 15,000 T. of ore were treated experiment-

Jan 1, 1919

I. PRESIDING OFFICER. At all business meetings of the Institute the President, or, in his absence, the First Vice-President, or, in the absence of both of them, any other Vice-President or Director, chosen by the meeting, shall preside. At all other meetings of the Institute the President, or, in his absence, one of the Vice-Presidents, shall preside. If none of these be present the meeting shall elect a Chairman. II. ORDER OF BUSINESS. At each business meeting of the Institute the order of business shall be as - follows : 1. Reading of minutes-of preceding meeting. 2. Report of the President. 3. Report of the Treasurer. 4. Report of the. Secretary. 5. Election of Directors. 6. Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders. 9. Miscellaneous business. This order of business may be changed at any meeting, by a vote of a majority of the Members and Associates present. At all sessions of the Institute, other than business meetings, the order of pro¬ceedings and the time of adjournment shall rest in the discretion of the presiding officer. III. SECRETARY OF THE INSTITUTE. The Secretary shall keep a record of the proceedings of all meetings of the Institute. He shall be custodian of the corporate seal, of the minute books, and of all legal documents belonging to the Institute. He shall have charge, on behalf of the Institute, of all correspondence except such as pertains directly to the office of the Treasurer. He shall notify all Officers and Directors and all members of committees of their election and appointment; shall issue notices of all meetings of the Board, and of the annual and other business meetings of the Institute; and shall; in calling, special meetings of the Directors, specify the objects of such meetings. He shall act as clerk at all the meetings of the Board of Directors and at all meetings of the Institute. The Secretary shall be custodian of all technical or scientific papers submitted to the Institute for its consideration, shall have general charge and supervision of the editing and proof-reading of all material published by the Institute, and of the distribution thereof, and be ex officer Chairman of the Committee on Publications. On the first day of May following the year in which each volume of Transac-

Jan 1, 1925

By Fred A. Hale

Owing to the large area included in the Yellow Pine mining district, and the varied nature of its mineral deposits, a detailed geological description of the district could be covered only in an extensive monograph. This paper is intended as a description of the most prominent geologic features only with special reference to those of economic importance. The first mention of the district was in 1903 by J. E. Spurr, who briefly describes the structural geology of the Spring Mountain range. In 1906, H. F. Bain2 briefly described the Potosi mine. James J. Hillla of the United States Geological Survey, visited the district for a brief period in 1912, the result of which is an excellent reconnaissance report, covering the district in some detail but necessarily with brevity. Since that time, articles covering special features of the district have appeared in the technical press, including some by the writer, and a notable description of the Boss mine, by Adolph Knopf,4 appeared in 1915. Development of the district during the past few years has progressed so rapidly and with so many notable discoveries, particularly with reference to the rare metals, that a further description at this time may prove of interest. The writer&apos;s acquaintance with the district is based on 7 years&apos; continuous residence in the vicinity, beginning with the spring of 1910. A. Location and Topography The Yellow Pine mining district is situated in the southwestern portion of Clark County, Nevada, about 300 miles northeast of Los Angeles, along the line of the Los Angeles & Salt Lake Railroad. The district extends from Mt. Olcott on the north to the California line on the south,

Jan 1, 1918

By Jack D. Arthur

The Surface Mining Control and Reclamation Act of 1977, as amended, and related regulations take blasting safety into consideration by requiring compliance with existing state and federal laws. The regulations are based on blasting practices developed by the industry, as well as research and experimentation by the US Bureau of Mines and explosive manufacturers. Residential areas in the proximity of surface mines have made it mandatory that blasting operations be conducted under restrictions and requirements designed to protect the public and structures located within 0.8 km (0.5 mile) of any surface blasting activities. Restrictions against blasting apply where dwellings, schools, churches, hospitals, or nursing facilities are within 305 m (1000 ft) of blasting operations. They also apply where wells, petroleum or gas storage facilities, municipal water storage facilities, fluid transmission pipelines, gas or oil collection lines, and sewage lines are within 152 in (500 ft) of blasting operations.

Jan 11, 1979