Search Documents

By W. W. Weigel

THE mines of the St. Joseph Lead Co. in St. Francois County, Missouri, form a roughly triangular area of about 45 square miles. Locally this is known as the Lead Belt. The four operating mines in the area at present are the Federal, Leadwood, Desloge, and Bonne Terre, in decreasing order of mine area and daily production. Mining began in 1864 and has been carried on in the district continuously since that time. [ ] As a group, the Lead Belt mines now handle 20,000 gal. per min. of water, average head about 465 ft., against a normal daily ore tonnage of 21,200 tons. For a six-day operating week this gives a ratio of 6 ½ tons of water per ton of ore. Total average pumping in 1931 was about 15,000 gal. per min. Since that time a large area of virgin territory has been opened, much of which has had temporary flush flows. About 75 per cent of the water enters in certain restricted very wet areas. Production figures are given in Table I. The figures by divisions for 1931 and 1941 are not exactly comparable, as there were several transfers of pumping loads from one division to another during that period of time. GEOLOGY The basement formation in the Lead Belt area consists of the pre-Cambrian rhyolite porphyry and granite. Overlying this is the La Motte sandstone, of Middle Cambrian age, which offers a good medium for circulation of water. It varies in thickness up to 400 ft. Above this is the Bonne Terre dolomite, approximately 375 ft. thick, which in turn is overlain by the 150-ft. Davis shale. The formations above this, present in the Lead Belt in small areas only, are of minor importance. The ore bodies occur as large, horizontal tabular masses or as long, narrow runs; they are found throughout the Bonne Terre but largely in the lower 150 ft. The rather indefinite contact with the La Motte is a favorite ore horizon. Mining is entirely by open stope and pillar breast systems. To the south, west, and north of the district, sandstone outcrops are few and limited. Heavy faulting bounds the district on those sides and probably there is little if any artesian circulation from those directions. To the east, the La Motte rises to an outcrop area of about 40 square

Jan 1, 1943

By W. W. Weigel

The mines of the St. Joseph Lead Co. in St. Francois County, Missouri, form a roughly triangular area of about 45 square miles. Locally this is known as the Lead Belt. The four operating mines in the area at present are the Federal, Leadwood, Desloge, and Bonne Terre, in decreasing order of mine area and daily production. Mining began in 1864 and has been carried on in the district continuously since that time. As a group, the Lead Belt mines now handle 20,000 gal. per min. of water, average head about 465 ft., against a normal daily ore tonnage of 21,200 tons. For a six-day operating week this gives a ratio of 6½ tons of water per ton of ore. Total average pumping in 1931 was about 15,000 gal. per min. Since that time a large area of virgin territory has been opened, much of which has had temporary flush flows. About 75 per cent of the water enters in certain restricted very wet areas. Production figures are given in Table I. The figures by divisions for 1931 and 1941 are not exactly comparable, as there were several transfers of pumping loads from one division to another during that period of time. Geology The, basement formation in 'the Lead Belt area consists of the pre-Cambrian rhyolite porphyry and granite. Overlying this is the La Motte sandstone, of Middle Cambrian age, which offers a good medium for circulation of water. It varies in thickness up to 400 ft. Above this is the Bonne Terre dolomite, approximately 375 fl. thick, which in turn is overlain by the 150-ft. Davis shale. The formations above this, present in the Lead Belt in small areas only, are of minor importance. The ore bodies occur as large, horizontal tabular masses or as long, narrow runs; they are found throughout the Bonne Terre but largely in the lower 150 ft. The rather indefinite contact with the La Motte is a favorite ore horizon. Milling is entirely by open stope and pillar breast systems. To the south, west, and north of the district, sandstone outcrops are few and limited. Heavy faulting bounds The district on those sides and probably there is little if any artesian circulation from those directions. To the east, the La Motte rises to an outcrop area of about 40 square

Jan 1, 1943

E.T. CONNER;. Scranton;. Pa-I had the honor of being associated with Mid. Griffith in an investigation of the Scranton mine cave problem several years ago; in the course of which we investigated rather carefully the bearing strength of various materials that might be utilized for, the support of over We found that there were no reliable data as to the resisting strength, for instance, of gob pillars or timber cogs or cribs, nor as to the amount of compression that might be expected under a given burden. We made a series of tests at the Fritz engineering laboratory of Lehigh University, from which we, reduced certain conclusions, subject, however, to further test before they could be definitely recommended. Onr study of the subject was later checked by a commission appointed by the Governor of the State of Pennsylvania, to investigate the same subject the subsidence of the surface, and the danger entailed thereby. The State, commission made a series of tests on a much more ambitious scale at Pittsburgh, in the laboratory of the U. S. Bureau of Mines, and their tests agreed quite closely with those that Mr. Griffith and I had made. As the result of our study, we determined that the most elastic support is the ordinary timber cog or crib, while the most rigid support is a

Jan 1, 1918

By P. Barnes

The tabular statement accompanying this note shows the money cost in each of the three departments of manufacture, of 17 leading items, and also the proportion (expressed in a clecimal fraction) which each of these items bears to the total cost. The statement can hardly be taken for more than an average illustration of the clear showing of ratios and of results which may be made by such an arrangement, for not only will these items vary from month to month in any given works, but the methods themselves of manufacture differ widely in different works. It is obvious that such a statement, however useful it may be, must be submitted with but exceedingly little explanation or discussion, or with none at all, for the reason that to enter at any satisfac-

Jan 1, 1879

By Chester Washburne

LEASING the Teapot dome to the Mammoth Oil Co. is the culminating anticlimax of the "conserva-tion movement." It is just the touch required to make a full fiasco of the whole affair. If the revered wielder of the "Big Stick" were still with us, we could hear it fall harder than it did on Ballinger. Of all the oil reserves set aside by presidential decree, there was only one which certainly could con-serve much oil for the future. This was Naval Reserve No. 3, on the Teapot dome, Wyoming. After secret negotiations, carefully guarded from the press and from the knowledge of other oil men, we are suddenly informed that this last and only known chance to save much oil for future naval needs has been given away for early development.

Jan 6, 1922

By J. D. Lubahn

The influence of precipitation from solid solution on the subsequent deformation resistance of alloys is well known. However, the influence of precipitation or aging that occurs simultaneously with deformation may be entirely different and of considerable importance. It is thought1 that the presence or absence of a yield point jog in impure iron at room temperature and the presence or absence of discontinuous flow at higher temperatures may be directly related to aging phenomena, particularly since the yield point jog is absent when the carbon and nitrogen are sufficiently removed.2 As a preliminary attack on the problem of simultaneous aging and deformation, three kinds of tests—constant strain rate tensile tests, constant load creep tests, and variable strain rate tensile tests—were carried out on an age hardenahle aluminum alloy. Constant Strain Rate Tensile Tests Stress-strain curves at a strain rale of about 0.001 min-1 were obtained for specimens of 61S that had been quenched into liquid nitrogen after a one-hour solution treatment at 521°C, then aged at room temperature 10 min., 20 min., 4 hr, and 26.5 hr before testing. Strain-time curves were obtained on the same chart with the stress-strain curve by means of an auxiliary pen, driven parallel to the axis of the chart drum at constant speed by a synchronous motor and gear chain. The angle of rotation of the chart drum was proportional to strain. The strain rates reported are the measured slopes of the strain time curves. Constant strain rate was approximated (within a factor of 2) by manual adjustment of the oil inlet valve of the hydraulic testing machine in such a way that the course of the recorder pen was parallel to pre-drawn strain-time lines of the desired slope. The specimens were machined from 9/16 in. rod. The cylindrical portion was 0.357 in. in diam by 13/4 in. long and

Jan 1, 1950

By W. W. Cotter, W. R. Clark

WEBSTER tells us the word "extrude" means to "force, press or push out; to protrude." As applied to the metal industry, the process consists largely of forcing plastic elements (plasticity usually obtained by preheating), through dies of predetermined profiles, into constant sections of considerable length and weight. Most of the "virgin" metals are quite malleable under this process, likewise many of the commonly used "alloys" in various industries, when basic elements are proportioned or combined within the natural laws and limits of good metallurgy. Several of the foundry alloys, both ferrous and nonferrous, together with some of the heat-treatable light metal mixtures, are decidedly weak and hot short at ordinarily plastic ranges, and consequently are troublesome or quite incapable of commercial extrusion. DEVELOPMENT OF PROCESS This process was conceived some time before 1800 and during its first century was employed almost entirely in making lead pipe, plumbing fittings and coating electrical cables. As a result of contact and experience with the lead industry and presses, Alexander Dick, of London, England, is credited with first having applied the principles of extrusion to brass, and in 1894 brought out a 500-ton horizontal press powered by hydraulics. A duplicate of this unit was imported by one of the Connecticut brass mills and was in experimental operation by 1900. During the first five years of operation, this press proved the value of the method to American industry, as it immediately revolutionized and converted the manufacture of brass rod from a 15-pass cold-rolling operation, with elimination of several intermediate anneals and cleanings, to an extrusion and a finishing draw. Likewise, ornamental brass and bronze moldings formerly cast and machined were produced in one squeeze on the extruder. The extrusion operation, being entirely that of compression, deforms the material without tensile stresses and can be used on delicate mixtures under heat, which cannot be hot-worked by straight hot-rolling or roller piercing. Base slabs of clock-brass strip were early in line of development or improvement, as were the brass bronzes (Naval brass, Muntz metal, manganese bronze, and others), popular as engineering materials for bolt stock, as well as structural shapes for marine and other mild conditions of corrosion. By 1910, American engineers undertook to design tube shell extruders, but were unsuccessful. The first World War began before fabricators could procure the more substantial designs of tube extruders produced in Germany; and it was not until the middle twenties that better models of the Universal extruders (double-actioned presses), equipped with hydropneumatic accumulator systems and other modern equipment, were available in the United States.

Jan 1, 1945

By H. M. Otte, A. G. Crocker

SLIP, twinning, stacking faults, and precipitates on well-defined planes in a crystal produce traces that are visible on either a polished or an etched surface. The purpose of this note is to establish the usefulness and limitations of the information obtained from such traces when determining the orientation of single crystals or grains in a polycrystal. Attention will be confined specifically to traces produced by octahedral planes in cubic crystals, though most of the remarks can be taken as more generally valid. The problem of determining the crystal orientation is completely solved in principle' and in particular for the special case under consideration.1'2 Tables are available3 in which the orientations can simply be looked up when given the two or three angles between the traces. Thus a quick and simple method is available for obtaining the orientation of a crystal from surface traces. In this note two examples will be given from recently published papers and will show the use of the method with the aid of the Tables, as well as some of the precautions that should be taken in the procedure. As part of an analysis of X-ray Kossel lines, Peters and Ogilvie 4 determined from them the crystallographic orientation of the specimen. They chose a Cu-5.10 wt pct Si alloy that had been partly transformed from the a (fee) phase to the k (hcp) phase. The latter formed as very straight platelets along the octahedral planes of the a phase, and a photograph (Fig. 7 of Ref. 4) was reproduced in the paper4 of the region for which the orientation had been determined from the Kossel lines. Apart from a very small area (about 0.15 mm diam) near the top center of the photograph, the region shown was clearly all of one orientation. Traces in four different directions were readily identified. Starting with the smallest angle and proceeding counterclockwise, the angles between the traces were measured to be 27° 43', 55° 16', 64 3 43 1, and32"26'. These add up to 1802 08 1, indicating a cumulative error of 8'. The correct values should, of course, be taken from the original glass plates, or at least from prints on distortion-free paper, so the precision of the quoted values is actually greater than their accuracy. The solutions can be looked up in the Tables3 in four ways, depending on how the angles are paired, tion for the minutes of arc is required and the solution obtained will be identical for all the four pairs if the values of the angles are not in error. In a practical situation, such as this one, there are several sources of error, so that the four solutions obtained will all be slightly different. An arithmetic average of the four solutions is mathematically incorrect, but may, in special cases, give an answer close to the correct one. A rigorous procedure for refining the orientation has been described by Mackenzie;5 he gives a least-squares method that can be applied, if necessary, to this type of problem. The orientation thus determined can be compared with the one from the Kosel lines and discrepancies larger than the experimental error assigned to nonor thogonality of the X-ray or electron beam to the specimen. Here the example will only be used to illustrate the general procedure for making a very rapid rough check. From measurements on the stereographic projection, Fig. 9 of the paper,4 we can determine that the surface normal is approximately (0.434, 0.704, 0.562). From the Tables3 we find, using 28°, 55" as a good approximation to the first pair (27°43', 55°16'), that the surface normal is (0.453, 0.678, 0.579).* These two values are within 2 deg of each

Jan 1, 1967

By H. S. Martin

The Phosphate Recovery Corporation operates three flotation plants, Nos. 1 and 2 concentrators about three miles northeast of Mulberry, Florida, and No. 3 plant at Wales, Tennessee. These plants represent the first commercial phosphate flotation operation and are also believed to be the largest nonmetallic flotation operation in the world at the present time. The details of this paper will be confined to plant No. 2, this being the newest and largest concentrator in Florida, and the flow sheet being practically the same as at plant No. 1. The No. 3 plant has been operated but a short time and has been shut down since December, 1932, on account of the decrease in phosphate rock production. The phosphate washers usually are located centrally on a known deposit so that about two hundred acres of ground can be mined economically to each washer location. The washers are moved to new areas when the distance becomes too great for economical pumping. The flotation plants are built either adjacent to a washer, so that current debris may be utilized, or on the site of a former washer where there is sufficient accumulated debris available for mining, and the flotation plants must also be moved from time to time. Most of the water used in the Florida flotation plants is recovered after passing through a circulating system where most of the fine suspended matter is settled out, but some make-up water is obtained from deep wells near the plant. Power is obtained from the Tampa Electric Co. through the distribution facilities of the International Agricultural Corporation. Flotation concentrate is hauled from the plant by trolley over the International Agricultural Corporation's trolley system, to the drying plant at Prairie, one mile northwest of Mulberry. Ore Treated In the pebble phosphate district of Florida, the phosphate mineral, or collophane, is usually found in horizontal beds of varying thickness

Jan 1, 1935

By John V. Beall

They let the whole world know again that not only could we do it, but we make it look easy. The great crews before Scott, Irwin and Worden of Apollo 15 have all blended warm humor, informality and dexterity to put on a good show: but it keeps getting better and the last one was the best. Scott's rendition of Galileo's experiment using a hammer and a feather--not just any feather, but a falcon feather after the name of the LEM-was priceless. One generation of school kids will never forget that lesson. The final touch was in the "would-you-believe''" category, Now if English astronauts had been performing the mission, the sign-off would have been typically low key. Something like; "well its tea time, chaps; we'll have to toddle along." Apollo 15 surprised and thrilled spectators by blasting off to the Air Force song "Off we go into the wild blue yonder" and leaving a camera behind to photograph their own ascent. Now that is what we call showmanship. There is another aspect to our space show and that is that it cost billions of dollars to put on. With that kind of backing, the world for an audience and in the face of grave personal risk, one would expect the space explorers to be all business. Instead they did their jobs with limpid buoyancy. Our older readers will recall and contrast a movie of the thirties and the tense atmosphere when they had to talk that kid up there (Franchot Tone) down through the zero ceiling. A feat of considerably less difficulty than docking LEM. but nevertheless the gut tightening drama was absent in the latter event. In another example, few of us can visualize reporting back after a business mission to one of the old barons such as J. P. Morgan in any but the most sedate and business-like terms. In fact we don't have to go that far back, as we can think of a few pepper-pot bosses we have had to whom one always played it straight.

Jan 1, 1971

By J. Lyndon Rosenblad

This chapter describes the development of a rocklike model material for use in tests with a rock-blocks model to investigate the failure mechanism of a discontinuum. In order to provide reliable results, the model material must be characteristic of natural rock and obey the laws of similitude. Initially, the development of such a material does not appear to be a difficult problem. Only when one undertakes such a task does he realize how little is actually known, and that there is considerable work yet to be done. A material that simulates rock in all of its physical properties probably will never be developed. There is now and probably always will be room for improvement. Improvement is needed not only in the component materials but also in the technique of preparation. The material developed and subsequently described in this chapter simulates rock in general and a schistose gneiss rock in particular. The material possesses many rocklike physical properties not found in previously used model materials. One of the most significant improvements of this material is that there is an increase of Young's modulus with an increase in confining pressure as determined by triaxial compression tests. A change in the usual procedure of material preparation was used to develop this material and is also described. MODEL MATERIALS USED IN THE PAST Intact Materials Numerous materials have been used by investigators in models in the past to simulate a wide range of prototype materials. Some of the materials used include cork, plastic, concrete, plaster of Paris, portland

Jan 1, 1972

By Alvin Kaufrnan

This chapter will deal with the policy issues relating to mineral land disposal. The first portion of the chapter will discuss in general terms the legal systems utilized in disposing of mineral rights and the major problems encountered; the second section will comprise an analysis of the policy alternatives with emphasis on the pricing aspects. In this section, we are not attempting to provide a legal text, but simply to outline very briefly and sketchily the details of the systems. More detailed information can be obtained by contacting the appropriate governmental agency for specific information. Mining laws throughout the world are based on two major legal groupings: English Common Law and the Civil Law. These basic systems are often modified by Islamic Law and by negotiated -mixtures of these. Under English Common Law, which is embraced by the United States, Canada, and many of the members of the British Commonwealth of Nations, individuals can hold property and can extract minerals from it. The owner can dispose of minerals as he sees fit, either through contract, deed, or whatever other system is appropriate. CIVIL LAW Under Civil Law (also known as Regalian Law), mineral ownership is normally placed in the state, regardless of who owns the surface. This legal system applies in most European countries and their former colonies. It is derived from Roman law. The mineral deposits, thus, are worked under concessions. Most countries use a negotiated concession system and sometimes a combination of negotiation and competitive leasing. The negotiated system has advantages as well as disadvantages for both government and industry. In a system where the government administratively determines who is to get what, the concessions are normally large. Frequently they range up to several millions of acres and involve a considerable investment on the part of the concessionaire. There is no duplication of effort on the part of producers to obtain information, since a single concessionaire controls a given area. Consequently, less money is spent in toto because several prospective operators are not required to seek the same information. The system also has the advantage to the industry of permitting the concessionaire to select and retain the best producting area. Thus, major developmental expenditures are made on the production unit only, with a resulting reduction in the risk factor. The large initial size of the concession also minimizes the possibility of expending a large bonus payment for a barren property. The major governmental advantage of a concession is its flexibility in accomplishing other national objectives. For example, a lease could be negotiated at less than fair market value, but requiring substantial de-

Jan 1, 1976

By J. H. Faulk

An examination is made of the various factors influencing drilling rate and drill bit life in various diameter holes. It is concluded that drill bits in the size range 4% to 6 1/4 in. can be used to attain substantially the some daily drilling progress as conventional size bits in soft rock drilling operations. An examination of the most important factors influencing "hazard of losing the hole" in the different hole size results in the conclusion that the smaller hole sizes can probably be drilled at reasonably low risk. However, this risk will be somewhat greater in the smaller diameter holes, requiring that special drilling and mud engineering practices be used to make small diameter holes practicable in soft rock drilling operations. An engineering analysia is made of the power and hydraulic requirements of several drill string-hole combinations to test the feasibility of drilling .small diameter holes in soft rock areas. Large econormies in rig power requirements appear possible by drilling .smaller .size holes in these operations. INTRODUCTION The industry now is re-examining the utility of small diameter holes in the light of substantial technical advances made in recent years. Faced with increasing cost of finding reserves and with proration after developing them, the industry must either develop methods of economizing or receive a lower rate of return on investments. Small diameter holes appear to involve an attractive method of economizing. Our objective is to determine if this is technically possible in soft rock operations. Soft rock, as used in this report, refers to those formations of a "drill-ability" corresponding to that of all Gulf Coast formations shallower than and frequently including much of the Eocene rock system. An important phase of technology which we shall examine is relative drilling rate and bit footage which may be obtained with various size bits. Rig operating efficiency, particularly as influenced by hazard, is also discussed in detail. The technical conclusions resulting from these examinations are used to develop sample drill string design and rig horsepower requirements for drilling holes as smaH as 4 3/4 in. and larger. The principal criterion used for the drill string design is that approximately the same daily drilling progress would be possible in all size holes in soft rock operations. This facilitates a comparison of rig size required for drilling the hole sizes in the range between 4 3/4 and 8 3/4 in. BROAD PROBLEM OF DRILLING RATE AND BIT FOOTAGE The three factors controlling daily drilling progress are: (1) drilling rate of bit while on bottom turning, (2) bit footage, and (3) rig operating efficiency. Let us look now at the first two of these factors. Drilling technology has progressed to the point that a semi-quantitative analysis of the effect of various operating variables upon these factors can be made. Those factors which apparently limit both drilling rate and bit footage for bits now in use are: (1) bit design, (2) weight on bit, (3) hydraulic cleaning capacity for bit cutting surfaces and hole bottom, and (4) rotary speed. (We neglect the effect of mud and formation properties because these factors arc the same for the various size bits.

Jan 1, 1957

By D. W. Levinson, L. E. Tanner

DURING the course of an investigation of the zirconium-iron-tin system the zirconium-iron system was reexamined up to 55 pct* Fe. The alloys pre- visible melting3 and X-ray diffraction studies were made of samples of the alloys. The ferromagnetic properties of ZrFe2were determined by Professor P. W. Selwood* using a modified Faraday balance.4 The zirconium-rich portion of the phase diagram is presented in Fig. 1 and compared with the work of Hayes et al.1 The maximum solubility of iron in ß is somewhat decreased while the eutectic temperature is raised. There seemed to be no change in the eutectic composition of 16 pct Fe. Since the base material was so low in iron content, it was possible to establish the maximum solubility in a between 0.017 and 0.025 pct Fe at the eutectoid temperature. The observation of fine ZrFe, particles in the micro structure of a specimen of 0.012 pct Fe alloy quenched from 700°C indicated that the solubility drops below this composition at 700° C and lower. Further study was made of the intermediate phase ZrFe2. wallbaum5 identified the compound initially as ZrFe2 with a C 15 (MgCu2) structure, placing it at 55 pct Fe stoichiometrically. Hayes et al.1 believed they found the phase at about 47.2 pct Fe and called it Zr2Fe3 but reverted to ZrFe, in the discussion of their paper.6 Jordan and Duwez7 confirmed Wallbaum's work as well as finding the same single-phase structure to about 62.3 pct Fe or Zr0-61 Fe2-18. In order to establish the ternary phase relations in the zirconium-iron-tin systema the exact position of this phase had to be known. This was accomplished by X-ray diffraction, visible melting, and metallographic techniques. Elliott8 obtained a single-phase ZrFe2 X-ray diffraction pattern from an alloy of about 55 pct Fe. This was confirmed in the present study with an alloy of 54.81 pct Fe. However, extra lines (attributable to a or ß zirconium) were found in diffraction patterns of the 47.42 and 49.83 pct Fe alloys. The melting characteristics of these same alloys were studied by suspending 47.42, 49.83, and 54.81 pct

Jan 1, 1960

By William M. Barret

In order properly to evaluate the data related to geomagnetic surveys, it is highly desirable to have all the available information concerning the magnetic properties of the involved media. This is true of surface as well as subsurface formations and becomes of increasing importance as advancement in instrumental and interpretative technique permits the analysis of relatively slight magnetic reflections of buried masses. Since the magnitude and areal distribution of the usually complex resultant magnetic field at the surface of the earth is a function of the susceptibility1 of the involved matter, it necessarily follows that susceptibility determinations will afford valuable data for geophysical correlation. The present method was developed to meet the need for routine analysis of specimens in the geomagnetic laboratory where it was felt that general utility, ruggedness, ease of manipulation and reproducibility of results were of greater importance than extreme sensitivity. Electric Circuits The electric circuits are illustrated diagrammatically in Fig. 1. Current from the battery, B, passes through the variable resistance R1, reversing switch S1, double-break key K1 to switches S2 and S3. From S2 it flows through variable resistance R2, ammeter A2, to the primary coils of the fixed mutual inductance Mf and variable mutual inductance M,. . From S3 it passes through variable resistance R3, ammeter As, to the primary winding of the fixed mutual inductance MI, which is designed to receive the test sample. The ballistic galvanometer2 or fluxmeter3 G is connected in the circuit containing the double-break key

Jan 1, 1932

By E. S. Machlin

THE function of this paper is to present certain results based on the fact that the strain energy arising from the solution of out-of-size solute atoms into the solid matrix is free energy and not internal energy, and that this strain energy is almost wholly shear strain energy as Zener1 pointed out. One natural consequence of this fact is an expression for the excess entropy of mixing due to the strain energy. Also, a derivation of the integral molar free energy of mixing partitioned to strain energy will be made using the model of Lawson2 and thermodynamics. This derivation has the advantage of showing in a simple way the assumptions involved in Lawson's treatment. The excess entropy of mixing partitioned to strain energy can be derived in two ways. The first way makes use of the fact that the strain energy is almost wholly in the form of shear strain energy. In this case, as Zener1 pointed out, the change in entropy due to the addition of shear strain energy is to a first approximation given by ?S/?? p,T = - ?lnµ/?T p,? Hence, the excess entropy of mixing partitioned to strain energy will be given by Sx ? = ?S/?? p,T Gx ? = - ?lnµ/?T p,? Gx ? where, Gx ? is the relative integral molar free en- ergy partitioned to strain energy; S is the entropy; is the shear strain energy; µ is the shear modulus; T is the absolute temperature; p is the pressure; and ? is the shear strain. Zener,1 as well as others, has pointed out that the shear strain energy stored in a compressible isotropic solid due to the insertion of an off-size incompres-sible sphere into a spherical hole in the solid, is approximately given by 2/3 µ/O (O°I - O)2 where a is the volume of spherical hole and no , is the volume of sphere. If we now consider the introduction of one mol of such spheres into an infinite volume of solid, then the relative partial molar free energy excess due to strain energy alone is GM ? = 2/3 µ/v (v ° 1 - v)2 where v is the molar volume of solvent and v°1, is the molar volume of pure solute type 1. Let us consider that these spheres are the two types of atoms in a binary solution, then there will be a similar relation for solute 2. The total relative integral molar free energy excess due to strain is then, to the approximations stated above GM ? = GM ? x1 + GM2 ? x2 = 2/3 µ/v [(v ° 1 - v)2 x1 + (v ° 1 - v)2 x2]. Lawson's relation for the strain energy can be de-

Jan 1, 1955

By R. A. Morse, W. O. Keller

The properties of limestone reservoir rocks such as the distribution and degree of continuity of the pore systems, and the relative volumes and permeabilities of the systems making up the complex cause large variations between performance of individual limestone reservoirs and their susceptibility to secondary recovery methods. The effects of these factors on the mechanism of fluid flow cannot be adequately evaluated with presently developed concepts, laboratory data, and geological information. The observance and interpretation of the performance of individual limestone reservoirs provides, at present, the most adequate approach for evaluating the integrated effects upon performance of the many. now immeasurable variations in the properties of limestone reservoirs. INTRODUCTION The development and application of techniques for increasing the efficiency of oil recovery from natural reservoirs is a problem of primary importance to the industry. During the past several years, a great deal of effort has been expended by the technical personnel of the industry toward the improvement of present known methods of oil recovery. and evaluating the factors which control the susceptibility of particular reservoir types to economic application of secondary recovery methods. Providing adequate and accurate laboratory data on the properties of the reservoir rock and its contained fluids. together with good production statistics, are available, methods have been evolved for estimating with reasonable accuracy the performance of an oil reservoir under either continued natural depletion or conditions imposed by introducing additional displacing fluid into the reservoir from an extraneous source through the injection of gas and/or water. The susceptibility of limestone reservoirs to secondary recovery by gas injection is very much dependent upon gas-oil relative permeability relationships for the reservoir in question. In a rock formation in which the porosity is of the intergranular type such as is found in sand stones and some non-fractured dolomites, a representative sample of the pore structure can be obtained in a small core plug. In this type of reservoir, it has been shown that relative permeability data obtained from laboratory experiments can be Properly applied to evaluate the flow relationships actually observed during the depletion of a reservoir. In addition, a good idea of the fraction of the reservoir which will be swept by the injected gas may be obtained from the spacing pattern used and the permeability profile of cored wells. From these data, it has been demonstrated that reliable estimates of performance and recoveries under gas injection operations can be made for reservoirs in which the Porosity is of the intergranular type. Limestone reservoirs on the other hand often present much more complex problems. One reason that the performance of limestone reservoirs is so variable is that there may be, in reality. two or more pore systems, the integrated performance of which will depend upon the physical properties of each system and their inter-relationship. For instance, in a limestone reservoir, the main pore structure, as far as void spaces for storage of hydrocarbons is concerned, may be represented by the intergranular openings of the rock. Usually in limes and dolomites, the intergranular pore openings are very small and the matrix permeabilities extremely low. Often, as in the case of Many dolomite and oolitic lime reservoirs, this is the only pore system, and performance is observed to be very similar to that of a sand stone of similar permeability. However, in the great majority of' the limestone reservoirs, there is present, in addition to the intergranular pore system, a complementary system of openings caused by fracturing or solution.',' The openings in the latter system are usually many times more permeable than the intergranular pore system due to their much larger size, and may contribute almost all the fluid carrying capacity of the formation, even though their volume may be a very small part of the total pore space in the reservoir. Obviously, the performance of such a complex under either primary or secondary control will deend upon the distribution and degree of continuity of both systems, the relative volumes and permeabilities of the

Jan 1, 1949

By R. A. Morse, W. O. Keller

The properties of limestone reservoir rocks such as the distribution and degree of continuity of the pore systems, and the relative volumes and permeabilities of the systems making up the complex cause large variations between performance of individual limestone reservoirs and their susceptibility to secondary recovery methods. The effects of these factors on the mechanism of fluid flow cannot be adequately evaluated with presently developed concepts, laboratory data, and geological information. The observance and interpretation of the performance of individual limestone reservoirs provides, at present, the most adequate approach for evaluating the integrated effects upon performance of the many. now immeasurable variations in the properties of limestone reservoirs. INTRODUCTION The development and application of techniques for increasing the efficiency of oil recovery from natural reservoirs is a problem of primary importance to the industry. During the past several years, a great deal of effort has been expended by the technical personnel of the industry toward the improvement of present known methods of oil recovery. and evaluating the factors which control the susceptibility of particular reservoir types to economic application of secondary recovery methods. Providing adequate and accurate laboratory data on the properties of the reservoir rock and its contained fluids. together with good production statistics, are available, methods have been evolved for estimating with reasonable accuracy the performance of an oil reservoir under either continued natural depletion or conditions imposed by introducing additional displacing fluid into the reservoir from an extraneous source through the injection of gas and/or water. The susceptibility of limestone reservoirs to secondary recovery by gas injection is very much dependent upon gas-oil relative permeability relationships for the reservoir in question. In a rock formation in which the porosity is of the intergranular type such as is found in sand stones and some non-fractured dolomites, a representative sample of the pore structure can be obtained in a small core plug. In this type of reservoir, it has been shown that relative permeability data obtained from laboratory experiments can be Properly applied to evaluate the flow relationships actually observed during the depletion of a reservoir. In addition, a good idea of the fraction of the reservoir which will be swept by the injected gas may be obtained from the spacing pattern used and the permeability profile of cored wells. From these data, it has been demonstrated that reliable estimates of performance and recoveries under gas injection operations can be made for reservoirs in which the Porosity is of the intergranular type. Limestone reservoirs on the other hand often present much more complex problems. One reason that the performance of limestone reservoirs is so variable is that there may be, in reality. two or more pore systems, the integrated performance of which will depend upon the physical properties of each system and their inter-relationship. For instance, in a limestone reservoir, the main pore structure, as far as void spaces for storage of hydrocarbons is concerned, may be represented by the intergranular openings of the rock. Usually in limes and dolomites, the intergranular pore openings are very small and the matrix permeabilities extremely low. Often, as in the case of Many dolomite and oolitic lime reservoirs, this is the only pore system, and performance is observed to be very similar to that of a sand stone of similar permeability. However, in the great majority of' the limestone reservoirs, there is present, in addition to the intergranular pore system, a complementary system of openings caused by fracturing or solution.',' The openings in the latter system are usually many times more permeable than the intergranular pore system due to their much larger size, and may contribute almost all the fluid carrying capacity of the formation, even though their volume may be a very small part of the total pore space in the reservoir. Obviously, the performance of such a complex under either primary or secondary control will deend upon the distribution and degree of continuity of both systems, the relative volumes and permeabilities of the

Jan 1, 1949

By Valentin R. Garfais

The world's petroleum production in 1928 is estimated at 1,322,896,-000 bbl., an increase of about 62,000,000 bbl. over 1927, as compared with an increase of over 133,000,000 bbl. in the previous year. The daily average was close to 3,600,000 bbl., of which the fields on the American continent produced about 84 per cent. The most important development during the year has been the partial success of the attempts to temporarily control production without appealing to legislation and, as a consequence, the increasing realization that, in order to reach a permanent cure for this situation, some form of legislation is necessary to' make possible the conservation of the oil supply and the stabilization of the industry. The importance of such a control over American production is not merely local but worldwide, as the American oil supply is now and for years to come will be the controlling factor of the industry. United States.—Production in the United States, which in 1927 increased about 15 per cent. over the previous year, remained practically stationary in 1928, the total being estimated at 902,000,000 bbl., or 68.2 per cent. of the world's output. This uniformity in production during the last two years was due primarily to the curtailment of output from wells already drilled, it being estimated that the available or shut-in production at the end of the year was close to 500,000 bbl. per day, or equivalent to the combined production of Venezuela and Russia, the countries ranking second and third. Venezuela.—With a production estimated at 106,000,000 bbl., Venezuela has trebled its output in the last three years. The increase in 1928 was 43,000,000 which placed this country as second in rank, a position which it should easily maintain for years to come. The output could have been considerably larger had not the oversupply in the United States made it advisable for Venezuelan operators to enter into tentative conservation agreements. Russia.—In Russia, production has doubled in the last five years, and reached a new peak in 1928 with an output estimated at 87,800,000 bbl., or an increase of 10,000,000 bbl. over the previous year. Difficul-

Jan 1, 1929

By J. P. Kerr, W. H. Cordell

Conditions in the oil and gas industry in Indiana were about the same in 1935 as in 1934. This is especially true of the old Trenton area and the Harrison County area where production was steady and almost no exploration and development took place. The past year has seen an increase in drilling activity and a decrease in oil and gas output in southwestern Indiana. In the state, 224 wells were completed in 1935, of which 48 were oil wells, 61 gas wells, and 115 dry holes. A few of these were old gas wells deepened to oil horizons. Twenty-six wells started during 1935 were not completed by Dec. 31. Approximately one-half the wells drilled were within proven areas. A relatively large number of wildcats, especially in Daviess, Pike and Gibson Counties, were in search of new gas supplies to supplant the diminishing resources in those counties. The decreased production of gas was due largely to the fact that existing supplies declined more rapidly than new fields could be brought on. The Alford field, in Pike County, which produced the bulk of the supply in 1934, was called on to do likewise in 1935, but was unable to respond sufficiently to keep up the yearly production for southwestern Indiana. During the last half of the year, the Oaktown field, Knox County, was connected with one of the principal pipe lines of the state, which helped to keep gas production above an unusual low. The decline in oil production was due almost entirely to proration during the first eight months of the year. The proration affected Daviess, Pike, Gibson, Sullivan and Vigo counties, which produce about three-fourths of the total for the state. After proration was lifted, the wells never quite reached the conditions existing before proration. The average daily production per well in Indiana is less than two barrels. The outstanding development in Indiana in 1935 was the drilling in the Oaktown field immediately before and after the laying of the 6-in. pipe line to the field. Almost without exception the wells came in with an open flow of two to four million cubic feet. At the end of the year, 26 wells were connected to the pipe line. Development of this field will

Jan 1, 1936