Search Documents

By Frederick V. Lawrence

Broadly speaking, fluxes are substances which promote wetting and spreading or enhance the fluidity and manipulative properties of materials in joining, fusion, and smelting operations. The term most strictly applies to substances used to facilitate soldering and brazing; but in the discussion which follows, the definition will be broadened to include materials used to promote fusion in arc welding and which aid in the smelting of metals. In each of the mentioned applications, the role of flux and its composition differs considerably; consequently in the discussion which follows, fluxes for soldering, brazing, arc welding, and smelting applications will be considered separately. Soldering and Brazing Fluxes Soldering and brazing are metallurgical joining processes in which a joint is formed using a filler metal of composition dissimilar to that of the joined pieces (base metal). The filler metal, solder or braze, is always of lower melting point than the base metal. Consequently with these processes there is no melting of the base metal. The successful creation of the joint depends upon the wetting and spreading of the solder or braze around or throughout the joint. The obstacles to successful soldering and brazing are contaminants and tenacious oxide films on the metal surfaces. In soldering and brazing applications, fluxes act to remove and exclude oxides and other impurities from the joint. There is no fundamental difference between soldering and brazing. The distinction between them is made on the basis of temperature. Join¬ing operations carried out at temperatures above 500° C are termed brazing. The higher temperatures used in brazing enable higher melting point filler metals to be used which generally provide stronger joints. The higher temperatures of brazing processes also require fluxes which are substantially different from those used in soldering and which will remain effective at high temperatures. Consequently the distinction between soldering and brazing can also be made on the basis of the fluxes used. Soldering Fluxes Even thoroughly cleaned and degreased, metal surfaces still possess tenacious oxide films which inhibit the soldering of the joint. The reactions which form these films increase with increasing temperature. The rate of oxide formation and the tenacity of the film varies with each base metal. Aluminum, magnesium, stainless and high alloy steels, aluminum and silicon bronzes when exposed to air form hard, adherent oxide films. These metals require highly active and corrosive fluxes to remove and prevent the reformation of oxide films during soldering. Metals such as copper and silver, on the contrary, form less tenacious films at a lower rate, so that mild fluxes are sufficient. Soldering fluxes must dissolve or remove oxides and promote rapid wetting and spreading of the solder. The flux removes the oxide film by loosening and floating it off into the main body of the flux. The oxide removal is often aided by the alloying of the solder with the base metal, undermining small areas of the oxide and detaching them (Anon., 1959). The flux coagulates and suspends the oxide particles which have been loosened. The flux forms a protective cover preventing the reformation of the oxides, permitting the spreading of the solder and the formation of a metallic bond between the solder and the base metal. Constituents of Soldering Fluxes: Soldering fluxes are commonly grouped into three categories: highly corrosive, intermediate, and noncorrosive. One normally would choose to use the least corrosive flux which will give satisfactory performance.

Jan 1, 1983

By W. R. Ingalls

In reviewing the history of the metallurgy of zinc, I shall pass hastily over what is only of antiquarian interest. That has been excellently treated by Dr. Bernhard Neumann in "Die Metalle" (1904) and has been described briefly in my "Production and Properties of Zinc" (1902), in my "Lead and Zinc in the United States " (1908), and in other metallurgical works of more or less the same date. In this present monograph, I have it in mind to confine myself mainly to technical practice, especially to that of the last 75 years, prior to which period advance was slow and of no great moment. The ancients made brass by the cementation process, i.e., embedding copper in a mixture of calamine and carbon and heating, whereby zinc oxide was reduced and zinc was vaporized and combined with the copper. Zinc was isolated by some of the alchemists, who named it and knew something of its properties, but made no use of it. Long before then, however, zinc was produced in India. Later it was produced in southern China. Possibly the Chinese obtained their knowledge from India. The Chinese in remote places still produce small quantities of zinc. I have seen photographs of their furnaces; or pots, for they hardly deserve the dignity of being called furnaces. I imagine that they are the same that were used centuries ago, for I cannot conceive of anything more primitive. Anyway, it is certain that the idea of a commercial production of zinc in Europe was imported from the Orient, where the metal was known in commerce as Speauter and Spiauter, whence speltrum and finally our term spelter. Tutanego and Tuteneague are other old names. Dr. Isaac Lawson went to China about 1730, expressly to discover the method of its production. What connection there was between Isaac Lawson and John Champion we do not know, but the latter obtained in 1739 a patent for a process of distillation downward and at some time between 1740 and 1743 erected a works at Bristol and actually began the manufacture of spelter. A production of 200 tons per annum is mentioned. In about the year 1766, Rishop Watson visited the Champion works and saw the process in operation, which previously had been

Jan 1, 1937

By N. A. Zeigler

Considerable work has been and is being done on the changes of physical properties that take place in alloys at elevated temperatures, and much information on this subject is published. Much less is known, as pointed out by Rickett and Woodll about reactions between the alloys and atmospheric gases and still less is known abut changes within the alloy itself under the influence of heat and given atmosphere. Moreover, most of the work published has been done on the alloys of "heat-resisting" type, in which chromium is an essential ingredient, the behavior of all other alloys being quite unknown, except perhaps of decarburization produced at the surface by oxidizing atmospheres. It has been shown2 that iron, with total amount of foreign ingredients not exceeding 0.01 per cent, if heated in an oxidizing atmosphere at above 900" C., may be saturated with oxygen to 0.1 per cent. It was suspected that something of a similar nature may take place in iron-silicon alloys (transformer material), the mechanism of such processes being either a direct diffusion of oxygen into the alloy, or oxygen combining with silicon to form SiO2 or more complicated (silicate) inclusions. Another possibility to be considered was that during annealing in oxidizing atmospheres, when scale is being formed, silicon may oxidize preferentially at the surface, thus impoverishing the alloy in silicon. In collaboration with Dr. T. D. YensenP3 the writer set out to investigate this problem about two years ago in order to settle these questions. Testing Procedure In the first part of the investigation, two pieces of 4 per cent silicon iron, prepared in hydrogen atmospheres and forged to 3/4-in. square bar,

Jan 1, 1934

By Douglas L. Gerner

In the early 1950's fishermen and their families around Minamata Bay in Japan were stricken with a mysterious neurological illness. The Minamata disease, as it came to be called, produced progressive weakening of the muscles, loss of vision, impairment of other cerebral functions, eventual paralysis and in some cases coma and death. The victims suffered structural injury to the brain. Minamata seabirds and household cats which, like the fishermen, subsist mainly on fish, showed signs of the same disease. This led to the discovery of high concentrations of mercury compounds in fish and shellfish taken from the bay, and the source of the mercury was traced to the effluent from a factory. Since then there have been other alarming incidents. In 1956 and 1960 outbreaks of mercurial poisoning involving hundreds of persons took place in Iraq, where farmers who had received grain seed treated with mercurial fungicides ate the seed instead of planting it. Similar outbreaks occurred in Pakistan and in Guatemala. In Sweden, game birds and other wildlife, apparently poisoned by mercury-treated seeds, began to be noticed in 1960. The Swedish Medical Board in 1967 banned the sale of fish from 40 lakes and rivers after it was found that fish caught in those waters contained high concentrations of methyl mercury. In 1970 alarm rose in North America. Following the discovery of mercury concentrations in fish in Lake Saint Clair by an investigator working in Canada, restrictions on fishing and the sale of fish were imposed in many areas in the U.S. and Canada. Government agencies in both countries began to take action to control the discharge of mercury-containing wastes into lakes and streams.

Jan 6, 1973

By H. C. Rolseth, J. J. Calaman

6.4-1. Principles of Operation. The jet-piercing process is a patented thermal process which depends upon a characteristic of the rock which is termed spallability. In its simplest terms, spalling is considered as decrepitation resulting from differential expansion of rock crystals due to thermally induced stresses. The number of individual properties influencing the spalling characteristics of rock are so numerous and their interaction so complex that the only truly reliable way to ascertain the spallability of rocks under thermal shock conditions is to expose them to these conditions. However, laboratory and field work have determined the principal thermal, physical, and mechanical properties of rock which affect spallability (10, 18). The approximate relationship between spallability and these characteristics is as follows: [ ] where To is the critical temperature at which, it is believed, a rock becomes elastic or sufficiently plastic to prevent further spalling action. Thermal diffusivity takes into account the amount of heat used in saturating the medium itself during the migration of a heat front. The rate and degree of dimensional changes which influence the spalling tendency of the rock will depend upon the characteristic of the heat gradient in the rock. The greater the spalling tendency, the higher the piercing rate. Those properties most favorable to a high degree of spallability are: 1. Large linear thermal expansion at temperatures below 700°C. 2. High thermal diffusivity at temperatures below 400°C. 3. Equigranular interlocking structure with little or no fine-grained clay or mica alteration products. 4. No significant amounts of soft, low-melting, or elastic mineral or materials which yield after thermal decomposition.

Jan 1, 1968

By F. J. Chernosky

Most previous studies of coal flotation utilized chemically pure reagents. Since such reagents are not available in quantity, a study of various wmmercially available reagents as frothers was undertaken. Flotation procedures similar to those used in a large number of commercial coal flotation plants were employed. The reagents used were compared on yield-selectivity-wst basis. The selectivity was found to be relatively constant with yields above 70% but the reagent cost varied greatly. The types of reagents available were compared. In the past, a number of papers have been written on the use of various reagents as coal flotation frothers. For the most part, these have been an attempt to correlate the intrinsic chemical and physical proper- ties of the reagents or reagent groups to the floata-bility of various fine coals. Because of the type or nature of evaluations made, chemically pure reagents were normally used. Generally, these reagents are unavailable in commercial quantities. Therefore, the results obtained with these reagents were usually limited in usefulness to the plant operator or metallurgist. This paper presents the results of a study in which commercially available forms of various reagents were used as flotation frothers. Flotation procedures which would conform in general to those employed in a large number of commercial coal flotation plants were utilized. The objective of the test was to compare these reagents on yield-selectivity-cost basis, that is, 1) the yields obtained, 2) the ash levels obtained and 3) the reagent cost relating to these results. REAGENTS The reagents employed have been grouped into the following chemical classes: 1) aliphatic alcohols, 2) terpines, 3) glycols (synthetic water-soluble

Jan 1, 1963

By Charles MacDowell

Up to 1909 the American public had little knowledge of, or interest in, potash. Some remembered that it had to do with soft soap and sore throat, but further they knew not. In 1909-10, the German-American potash war, and the publicity attending hostilities, brought home to America the knowledge that potash was an important article of commerce; that Germany monopolized its production and distribution, and exercised all the prerogatives attending complete control. The present war, with its transportation embargo, has again directed attention to Germany's strength as a potash producer and her present unfortunate situation as a distributor. As a consequence, the search for potash takes on new life and it again becomes a subject of general interest. My first knowledge of potash came from a study of the German potash exhibit at the World's Fair in 1893. This investigation led to the recommendation that Armour & Co. engage in the manufacture of commercial fertilizers and the fertilizer branch was organized early in 1894. From then to now "potash" has been a live subject. Two and eight-tenths per cent. of the earth's crust consists of potassium oxide. It is an important constituent of feldspar, granite, and other igneous rocks. Potash is valuable commercially in a water-soluble form. In igneous rocks it is locked in so tight that it is of little value and no utilization in a commercial way has been made of these insoluble forms. Potash in water-soluble form is found in large deposits in Germany; in smaller deposits in Austria and Spain; and in brines in some of our Western arid basins. The deposits in Germany, Austria, and Spain are concentrations from sea waters containing potash derived from the decomposition of potash-bearing rocks.

Jan 2, 1915

By H. LeRoy Scharon, A. B. Cleaves

THE application of geophysical techniques in the A engineering surveys of the Philadelphia and Western Extensions of the Pennsylvania Turnpike System is unique inasmuch as this is the first time, (to the authors' knowledge), that such studies have been employed on a large scale on a major highway system. These investigations were confined to specific areas along the center line of the proposed Philadelphia Extension between Carlisle and King of Prussia, and the Western Extension between Irwin and the State line near Youngstown, Ohio, as shown in Fig. 1. Along the 100 miles of the philadelphia Extension, the geophysical surveys were confined to 137 individual cuts and comprised a total length of 37.4 miles of line. The Western Extension, 66 miles in length, has 108 individual cuts. The accumulated length covered by electrical resistivity studies was 17.3 miles. The depth of the cuts varied from a minimum of 10 ft to a maximum of 62 ft. The geophysical investigations were made for the purpose of determining depths to bedrock in the 245 proposed cuts and at the sites of various structures. The 'data also served as a basis for geological interpretations of the condition of bedrock, contact zones, rock types, water table, and other factors significant in highway construction. The geophysical method of investigation employed the use of the electrical resistivity principle using the Gish-Rooney type electrical resistivity meter and the Wenner electrode configuration.* Apparent resistiv- ities were determined for constant intervals to various depths and were correlated with surface geological observations and subsurface geological conditions revealed by key diamond drill holes situated within a given cut interval. From these correlations, depths to bedrock were postulated with notations on other geological features that might be pertinent to modern highway construction. Geology The bedrock underlying the areas of the extensions of the Turnpike afford an excellent academic study of the electrical resistivity depth method as well as a practical application to modern highway engineering. The rocks encountered on the Philadelphia Extension vary in age from pre-Cambrian to Triassic and Quaternary, whereas in the Western Extension, bedrock is confined to relatively flat-lying strata in the Allegheny, Conemaugh, and Monongahela formations of the Upper Paleozoic, Pennsylvanian. Glacial and Recent stream, valley, and terrace deposits are common. Philadelphia Extension The oldest bedrock encountered in this extension are igneous and metamorphic. These, encountered chiefly in Chester County, consist of the strongly

Jan 1, 1952

By J. D. Grace

Screening by centrifugal force is a unique subject, for all vibrating screens, with but one exception, depend on gravity alone to pass material through a sizing mesh or screen cloth. Centrifugal screening is one of the greatest advancements made in screening since the development of vibrating screens. It makes possible sizing in a range previously im-practical by mechanical methods. The centrifugal screen is specially designed for fine sizing from No. 4 separations to finer than No. 100 separations. Centrifugal force provides a positive control of factors that make fine particle separation practical and effective as opposed to gravity which is a fixed force acting only in a fixed direction, The centrifugal screen provides a control of the force of material against the screening surface, and also controls the distance of departure of the material from the surface and its rate of return. The centrifugal screen has a rotating drum that becomes a natural fan blowing air outward through the material being screened and carrying float dust and fines through the apertures with it. Screening by centrifugal force is an unique subject, for with the exception of only one vibrating screen presently on the market, all vibrating screens depend upon gravity to pass material through a sizing mesh or screen cloth. This one screen that sizes by centrifugal force and utilizes gravity only to convey material along the screen, is the Symons V-Screen. The requirements of the industrial minerals industry to meet ever-increasing stringent fine sizing specifications by a practical mechanical method accentuates the weakness of gravity, a fixed force acting in a fixed direction, as a prime force for fine sizing. It was apparent a force other than gravity was needed. This led to the development of a centrifugal screen to meet modern demands for practical fine sizing operations. Gyratory-type screens in use today were originally designed in a day when a 1/4-in. separation was normally considered fine sizing and 1/8-in. separations were extremely fine sizing. Although gyratory-type screens are sometimes used for separating below 1/8-in., they are not practical screens for this purpose. They were not designed to do this type of work. A growing demand for a practical means of making positive mechanical separations in a range of from 1/8 in. downward led to the development of the vibrating screen. These screens utilize higher speeds and lower amplitudes of vibration than

Jan 1, 1967

By H. W. Kerr, B. Soutiere

THE possibility of using unidirectionally solidified eutectic alloys as high-strength composite materials has been investigated by several workers. Unidirectionally solidified lamellar and fibrous eutectics have been shown to have good short-time structural stability at temperatures close to the eutectic melting temperature.'-4 Several investigations of both short-time high temperature tensile properties and creep properties of eutectic alloys have been carried out,3-" with promising results. Little work has been reported, however, on the thermal stability of eutectic alloys which have been unidirectionally solidified and subsequently deformed in compression. Since processes such as rolling and grinding introduce compressive stresses, and since the properties depend on the spacing and perfection of the composite structure10,11 this aspect is of definite importance if unidirectionally solidified eutectic alloys are to be considered for commercial use. A Cd-Zn alloy made from 99.999 pct starting materials was cast into a graphite boat and zone levelled12 to obtain a completely lamellar structure at one end of the bar. Sections from this region of the bar were removed, recast into 6.5 mm I.D. Pyrex tubing, and solidified unidirectionally upwards at a rate of 2.8 cm per hr. Specimens were cut from the solidified rods, heated in air at 200°C (0.88 of the eutectic melting temperature) for various lengths of time, and examined metal-lographically. Compression specimens were also cut from the solidified rod carefully machined to a length of & in., and deformed with the compressive axis parallel to the original growth axis to produce a total longitudinal strain of 12 pct. Some of these specimens were examined metallographically; others were heated in air at 200°C for various lengths of time and then examined. Metallographic examination of the deformed specimens showed the two types of deformation previously described; slip lines13 (smoothly bent lamellae) and kinks13,14 (sharply bent lamellae). Very close to the specimen ends there were a large number of deformation bands, but at a distance of about -re- in. the deformation was very localized, as shown in Fig. 1.

Jan 1, 1970

By F. L. Clerc

The lead and zinc region of SW. Missouri is interesting, not only by reason of the value of its output, which ranges in the neighborhood of ten million dollars a year, but even more because of the facilities which it offers for the study of certain forms of ore-deposits, of' which the loci and genesis are somewhat obscure. Although the mineral species found in the region are few and of common occurrence, crystallization has taken place on a generous scale, and unusual forms abound in many combinations, presenting examples of pseudomorphism, para-genesis, metasomatic replacement and the action of mineral-depositing and mineral-dissolving waters. For the mineralogist, lithologist, and specialist in certain lines of metamorphism, it has peculiar attractions, while the systematic geologist will perhaps find its chief claim to attention in the simplified problem it presents, in the study of ore-deposits. In addition to the phenomena above enumerated, it presents instances of well-developed comb-structure in the ores, fissures and faults, and slickensides—features usually associated with extensive movements in the earth's crust, and believed by some authorities to prove the deep-seated origin of the ores. In connection with these occurrences, the absence of all igneous rocks from this region is noteworthy and significant. For that reason, the simplified case presented by the Joplin region, from which these rocks have been eliminated as a factor, is specially valuable. Having had unusual opportunities to watch the development of this district, I have been deeply interested in the bearing of the revelations of the Joplin mines upon questions of universal importance to the science of ore-deposits; and it was to my great regret that the project of a meeting of the American Institute of Mining Engineers at Joplin, proposed in 1892, was

Jan 1, 1908

By J. David Lowell

For his contributions to the field of mining geology, a striking example being his brilliant inte.rpretation of the complex geologic history of the San Manuel District (Pinal County, Arizona) which resulted in the discovery of the Kalamazoo orebody, and for his lecture, "Copper Resources in 1970." On a low desert ridge six miles south of Cairo lie the remains of the world's earliest known mining town, Maadi of predynastic Egypt. Copper artifacts, including ingots and an ax head which was spoiled in casting, indicate that copper ore was smelted in Maadi, and radiocarbon dating has placed the activity at least as early as 3300 B.C. This is the oldest documented date for the use of smelted copper, the first industrial metal used by man. Copper was mined and smelted almost as early in Asia Minor and on the island of Cyprus, but the greatest development of the budding copper industry was in Egypt, where specific historical records show that about 10,000 tons of copper metal were produced in the period from 1850-1580 B.C. Contrast this production of 35 tons per year with the present world production of about 7 million tpy. Evolution of the Copper Industry The copper ore mined by the ancients was high grade, and the copper produced was expensive. The copper industry began with narrow high-grade veins, but has evolved to the point where massive earth-moving equipment can be operated in huge, low-grade open pits. Indian pits dug before 3000 B.C. in the Lake Superior district were in ore which averaged 15% Cu. His- torical research done by Arthur Brant has shown that copper cost in the Middle East in 1840 B.C. in terms of 1970 labor dollars was about $25 per lb. The copper mined in northern Europe in 1540 in the time of Georgius Agricola averaged about 8% Cu, and the cost in 1970 labor dollars was about $10 per lb. Average ore grade had dropped to about 6% Cu in 1890, and the cost of copper in the U.S. in 1970 dollars was about 45¢ per lb. Butte, Mont., was a good example of the efficiently operated vein mines of this time. In 1906, Daniel Jackling made a dramatic entrance into the copper scene with the Bingham Canyon open-pit copper mine and proved that more profit was possible mining 2% porphyry copper ore on a

Jan 1, 1971

By R. P. McLaughlin

IN most branches of the mining industry it is a well-recognized fact that care must be taken to protect the mineral deposit from undue physical injury. It is comparatively easy to grasp this idea when the mineral is a solid and the lives of workmen depend directly upon the care with which it is removed from its natural position, but when the product is a liquid. drawn up from pools several thousand feet beneath the surface of the ground through openings only a few inches in diameter, it requires some imagination to picture underground conditions and the changes which must often occur. The development of the petroleum deposits of California has been attended by numerous accidents, the results of which are readily noticed at the top of the wells and in the profit and loss accounts of the operators. Determination of the cause of these accidents has been the subject of considerable study, which naturally has fallen upon men familiar with technical methods. The greatest damage to the oil deposits of California has resulted from water finding its way into the oil-bearing sands, and it is the purpose of this paper to set forth briefly this phase of the oil industry. Much of the material here presented has previously appeared inn publications issued by the California State Mining Bureau, which, under the direction of State. Mineralogist Fletcher McN. Hamilton, has investigated the subject and taken steps toward improvement of conditions. The writer, having been in charge of this branch of the Bureau work, has gained considerable knowledge of existing conditions.

Jan 12, 1915

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred, indicated by a *. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) ANDERSON, AMIL A., Co. A, 309th Regiment Engineers, 84th Div., American E. F., Care Postmaster, New York. ARMSTRONG, HAROLD K., Pilot, Naval Aviation, U. S. Naval Air Station, Miami, Fla. BASSETT, ARTHUR F., Co. 6, -E. 0. T. S., Camp Humphreys, Va. BEDDALL, THOMAS H., Adjutant, 1st Battalion, 1st Gas Regiment, American E. F. BERNARD, CLINTON P., Candidate, 12th Observation Battery, F. A. C. 0. T. S., Camp Taylor, Ky. BROOKE, LIONEL, 50th Co., 13th Battalion, 5th Replacement Engineers, Camp Gordon, Ga. BROWNING, EDWARD, Corp., 1st Regiment Engineers, Co. D, American E. F. BUGBEE, EDWARD E., S. A. T. C. Headquarters, Raleigh N. C. BUTTERFIELD, G. BRUCE, CO. C, 605th Engineers, American E. F. CADOT, J. J., 1st Lieut., U. S. Air Service, American E. F., Care Post- master, New York. CARLOCK, J. B., Major, 2d Battalion, 1st Gas Regiment, American E. F., France.

Jan 12, 1918

By Frederick T. Fischer

The New Jersey Zinc Company began a program of exploration in Middle Tennessee in 1964. The target horizon of the exploration project has been the Knox Dolomite which is a low-yield aquifer over nearly the entire Central Basin of Tennessee (1). With the exception of a few hundred acres in the Wells Creek and Flynn Creek disturbances (astroblemes?), the Knox Dolomite in Middle Tennessee is known only in subsurface. In January of 1969, New Jersey Zinc announced the discovery of a major zinc deposit near Elmwood, southeast of Carthage. This is on the northeastern flank of the Nashville Dome where the nearly flat-lying beds have an average eastward slope of about 50 feet per mile. The anticipated development of a mining situation has emphasized the significance of hydrologic relationships in the region as a whole and especially in the Elmwood area. These relationships affect several areas of concern which ma be generally grouped into two broad classes; i. e. , (1) Problems of a Public Nature - involving the prevention of the contamination of potable aquifers, the prevention of the contamination of surface waters, the prevention of the capture of presently utilized water, etc.; and (2) Problems of Mining Economics - involving pumping capacity and costs, the possible need for equipment of special composition, underground environmental conditions, etc. Exploration drilling in Middle Tennessee has contributed additional information about the Knox aquifer and

Jan 1, 1970

By G. C. Weaver, G. T. Harley

Beds or lenses of potash and magnesium salts are found in a thick salt section (Salado) overlain by Rustler Red Beds in several members of which water is present and from one of which the rehery process water used by International is obtained. Most of the holes drilled are less than 1000 ft. deep, but some wildcat holes have exceeded 3- ft. cable or rotary tools are used to drill down to the salt. when samples of water are desired the cable rig is used, but when this is not necessary, and where caving material is present, the rotary rig has an advantage. The rotary rig has a further advantage in that only one machine is required to drill and core the entire hole, whereas the cable rig must be moved off to make way for the core drill. Casing is placed in the upper section of the hole as required to shut off water, and a 5 3/16 in. string is set in the top of the salt before coring starts. With the rotary rig drilling is often carried to the salt with no casing, as drilling mud seals off caving ground and water-bearing strata, and a string of 4-in. line pipe or 4-in. flush-joint casing is landed on top of salt. Several types of gasoline-powered core rigs have been used in the field and all recover a 2 1/2-in. core. More recently the Sullivan Model 37 rotary rig has been tried, and a Sullivan Model N has been adapted to use a rotary bit in the upper section. Core is recovered in 20 ft. sections with a double-tube core barrel, and the bit used is a bottom-discharge type set with diamonds. The drilling fluid must be a saturated brine to prevent solution and etching of the minerals present. Blowouts are apt to Occur from nitrogen gas trapped under the several polybalite beds, and some have been strong enough to blow the tools out of the hole. Core recovery is practically loo per cent. All holes are plugged after drilling, with cement through the salt section and opposite each water horizon* and mud through the remainder of the hole. Cores are carefully logged and preserved, and in sections containing potash and magnesium minerals they are quartered and analyzed. The correlation of Ore beds between drill holes is briefly described. Introduction Beds Or lenses of potash and magnesium salts are found at varying depths in a thick deposit of salt (Salado formation) in what is known as the Permian Basin, in southeast New Mexico and West Texas. The Salado formation is Composed chiefly of common salt (halite) with numerous beds of anhydrite, polyhalite, and the soluble potash minerals carnallite, sylvite and langbeinite. Many other minerals are present in small amounts but their Presence has no bearing On the coring technique. Before starting to core the salt section it is necessary to penetrate 300 to 600 ft. of unconformably overlying Permian sediments (Rustler formation) which are composed of red and gray clay, sand, anhydrite, dolomitic limestone and occasional lenses of salt. The upper part of the formation is predominantly anhydrite, and the lower part predominantly clastic. A thin bed of dolomitic limestone, known

Jan 1, 1948

By G. C. Weaver, G. T. Harley

Beds or lenses of potash and magnesium salts are found in a thick salt section (Salado) overlain by Rustler Red Beds in several members of which water is present and from one of which the rehery process water used by International is obtained. Most of the holes drilled are less than 1000 ft. deep, but some wildcat holes have exceeded 3- ft. cable or rotary tools are used to drill down to the salt. when samples of water are desired the cable rig is used, but when this is not necessary, and where caving material is present, the rotary rig has an advantage. The rotary rig has a further advantage in that only one machine is required to drill and core the entire hole, whereas the cable rig must be moved off to make way for the core drill. Casing is placed in the upper section of the hole as required to shut off water, and a 5 3/16 in. string is set in the top of the salt before coring starts. With the rotary rig drilling is often carried to the salt with no casing, as drilling mud seals off caving ground and water-bearing strata, and a string of 4-in. line pipe or 4-in. flush-joint casing is landed on top of salt. Several types of gasoline-powered core rigs have been used in the field and all recover a 2 1/2-in. core. More recently the Sullivan Model 37 rotary rig has been tried, and a Sullivan Model N has been adapted to use a rotary bit in the upper section. Core is recovered in 20 ft. sections with a double-tube core barrel, and the bit used is a bottom-discharge type set with diamonds. The drilling fluid must be a saturated brine to prevent solution and etching of the minerals present. Blowouts are apt to Occur from nitrogen gas trapped under the several polybalite beds, and some have been strong enough to blow the tools out of the hole. Core recovery is practically loo per cent. All holes are plugged after drilling, with cement through the salt section and opposite each water horizon* and mud through the remainder of the hole. Cores are carefully logged and preserved, and in sections containing potash and magnesium minerals they are quartered and analyzed. The correlation of Ore beds between drill holes is briefly described. Introduction Beds Or lenses of potash and magnesium salts are found at varying depths in a thick deposit of salt (Salado formation) in what is known as the Permian Basin, in southeast New Mexico and West Texas. The Salado formation is Composed chiefly of common salt (halite) with numerous beds of anhydrite, polyhalite, and the soluble potash minerals carnallite, sylvite and langbeinite. Many other minerals are present in small amounts but their Presence has no bearing On the coring technique. Before starting to core the salt section it is necessary to penetrate 300 to 600 ft. of unconformably overlying Permian sediments (Rustler formation) which are composed of red and gray clay, sand, anhydrite, dolomitic limestone and occasional lenses of salt. The upper part of the formation is predominantly anhydrite, and the lower part predominantly clastic. A thin bed of dolomitic limestone, known

Jan 1, 1948

The Library Board of the United Engineering Society is desirous of bringing closer to you the facilities and usefulness of your splendid Library. To that end, they have inaugurated a Service Bureau whose duty it shall be to maintain such a staff of expert searchers and translators as to insure prompt and thoroughly efficient service to those of our members whose absence from New York makes it inconvenient for them to pesronally consult the books and periodicals on our shelves. The Service Bureau is also arranging to keep such members as may desire it, posted on the current publications of any engineering subject in which they may be specially interested. The Charter of the United Engineering Society does not permit the Library to carry on any work of a commercial character and, therefore, the prices charged members for this service have to be kept down to a merely self-supporting basis. All the work done by the Library Service Bureau is strictly confidential.

Jan 9, 1915

By G. Pomey

Heat-resisting chromium steels and alloys treated at 825° or 9.50°C (1527° or 1742°F) in a carburizing atmosphere exhibit an extensive carbide precipitation. This carbide precipitation may be succeeded by the FeCr a phase or by a carbide with a higher carbon content. Point analyses carried out with an electron mi-croanalyzer make it possible to study the depletion of chromium in the matrix after precipitation has occurred and to determine the chemical composition of carbides. In particular the content in the carbides of Fe, Ni, and W, elements which substitute Cr, can be accurately determined. HEAT-resisting chromium steels and alloys employed in the construction of gas carburizing and carbonitriding furnaces are subjected to a succession of oxidizing atmospheres during heating and cooling and to carburizing atmosphere during isothermal stage. Such a sequence of thermal cycling causes embrittlement and corrosion in the furnace materials. A quantitative study of the structural changes induced in the furnace materials has not received much attention in the past. However, utilization of the electron probe microanalyzer and other modern techniques has permitted a point analysis of the various phases formed and to follow their relative evolution. This paper gives results as regards the nature and composition of the carbide precipitation and the distribution of chromium in the matrix during only the carburizing periods. The structural changes subsequently produced during oxidizing periods will be presented eventually. METHODS AND MATERIALS Metallographic, X-ray diffraction and Castaing electron-probe microanalysis1 techniques have been employed to study carbide precipitation and evolution and the changes in the composition of the matrix in heat-resisting steels and alloys.

Jan 1, 1961

By C. A. Heiland W. E. Pugh

The principle underlying the majority of magnetic intensity variometers is a comparison of the force to be measured with another force of known magnitude. The known force may be (a) of a magnetic nature, such as magnetic fields produced by magnets or coils, or (b) of a mechanical nature, such as (1) the elastic forces of wires, or (2) the force of gravity, such as employed in bifilar magnetometers and magnetic balances. In instruments of such type, usually a magnetic system is employed, free to move about either a horizontal or vertical axis, on some sort of a suspension. If the earth's magnetic field alone were present, such a system would adjust itself into the direction of the field or that of its components. Owing to the simultaneous action of the comparison force, however, the magnetic needle assumes a position that differs from the direction of the magnetic force; for all such instruments, the angle of deflection is given by tan = FIX, where F is the known and X the unknown earth magnetic force component. In other words, the magnetic system merely serves as an "indicator" for the position of balance of the two forces. Considering the matter from this point of view, it is not immediately obvious why the temperature of such a magnetic system should modify the results. In magnetic instruments, we may distinguish two different effects of temperature: (1) a magnetic effect and (2) a mechanical effect. The first is due to the fact that the magnetic moment of a magnet drops with an increase in temperature. This drop is characterized by the temperature coefficient of the magnetic moment (see equation 1). The second effect is due to the change in the torsion of suspension wires with temperature or to the expansion of lever arms of masses acting on magnetic balances.

Jan 1, 1934