Search Documents

By John Campbell

An approximate theoretical model is proposed to quantitatively predict freezing ranges Tf and hydrostatic tensions P developed within solidifying binary alloys, allowing for a certain amount of diffusion of solute in the solid during solidification. The maxima in ATf and AP as functions of composition are shorn to occur at smaller solute concentrations than would be expected from the equilibrium diagram, and are found to correspond closely to experimentally observed maxima in microporosity. THE freezing range of simple binary alloys appears to have been little studied, except for certain indirect observations on the defects, particularly microporosity and hot tearing, arising in long freezing range materials. Two theories relating to the freezing range of alloys and its effect upon porosity are reasonably well established, and appear to have been held in isolation from each other: a) From purely equilibrium considerations early researchers expected that an increase in solute content of an alloy should increase the freezing range (defined here as the equilibrium freezing range ?Tf = Tl-Ts where TL and Ts are the liquidus and solidus temperatures, respectively) and thereby increase the width of the pasty zone for a given set of conditions. This in turn should increase the difficulty of feeding the residual liquid through the dendrite mesh to compensate for the contraction on solidification, and consequently tend to increase the observed amount of porosity. From qualitative observations on steels Czikel1 reports an increase in porosity with increasing carbon content up to 0.46 pct C. More careful measurements by Whittenberger and Rhines2 on fourteen different alloy systems showed an approximately linear relation between ?Tf and pct porosity (although unfortunately the precise experimental data is not given). b) Conversely however, other authors3"5 propose that porosity is reduced by the presence of increased amounts of eutectic present at the final solidification temperature. Lees7 and Bochvar6 claim that the hot tearing of alloys is similarly reduced. Scheuer8 has put forward a theory to explain this effect, Fig. 1. The argument is basically that solidification progresses on a plane front through a relatively open dendrite network and is thus (the argument is not developed more explicitly) easier to feed. One would expect effect a) to operate at low solute contents, and b) to be important at higher solute contents, so that at some critical composition a max-

Jan 1, 1970

By Roy T. Southin*

The finding of Wojciechowski and Chalmers that columnar crystal growth can be stopped by an already existing network of equiaxed crystals is supported by other recently reported work on both static and mechanically stirred ingots.27,28 Support for the dendrite arm fragmentation mechanism, too, can be obtained by comparing the effects of spinning on ingots cast in a material which has a dendritic solid/liquid interface during solidification with one which has a cellular interface, since no evidence of change at the interface, other than a change in growth direction, can be found in the cellular material. But there are alternative ways of producing an equiaxed zone in materials which characteristically solidify with a cellular interface. For example, interrupted spinning of a normally cast ingot can do it. In this case it has been shown28 that the equiaxed zone is caused by the showing of dendritic particles from the top surface of the ingot to nucleate a network of equiaxed crystals which forms a barrier to the continued growth of the columnar grains. This showering has also been shown to be a major effect in materials solidifying with dendritic interfaces. It has also been proposed28,29 that, for an equiaxed zone to form, not only must nuclei be present ahead of the interface but also these nuclei must grow to sufficient size to be a barrier to the further growth of the columnar grains. A further requirement is that a network of these grains continually be produced ahead of the growing interface; otherwise there is a reversion to columnar growth as found by Wojciechowski and Chalmers. In normally cast ingots it is possible for nuclei ahead of the interface to grow since during a large portion of the solidification time there is no temperature gradient ahead of the interface,30 and, in fact, the liquid may be slightly undercooled.29 This then is the major difference between the work under discussion and normal industrial solidification conditions, since Wojciechowski and Chalmers imposed a considerable temperature gradient in the liquid. The statement in the Wojcieshowski and Chalmers paper that one needs to lower the temperature gradient

Jan 1, 1969

By S. A. Ford

I would like to call the attention of our Bessemer steel manufacturers to a few facts in regard to the action of the manganese in the spiegel with the oxide of iron in the blown iron. The oxygen is united with the iron as a magnetic oxide, as Gautier asserts, and this oxide is reduced to a protoxide by one atom of the manganese uniting with one atom of the oxygen of the magnetic oxide of iron. This oxide of manganese and the protoxide of iron thus formed unite with the silica which has been formed by the oxidation of the silicon in the pig iron. Mr. Snelus and others

Jan 1, 1881

By René de Batz

From 1754 to the end of 1895 the production of gold in Russia had been approximately as follows: Kilogrammes. Russia proper (Finland and the Caucasus),. .. 890 The Ural Region,........505,386 Western Siberia,........116,937 Eastern Siberia,........1,218,372 Total,.........1,841,085 of the value of more than $1,200,000,000.

Jan 1, 1899

By W. B. Mather

A SURVEY of the technical literature concerned with oil well drilling methods and particularly with rate of penetration by various cutting media on different types of rock provides a mass of conflicting data. This is especially true with respect to, (1) the relative efficiency of diamond, rotary and percussion drilling operations; (2) the costs of the various types of drilling; and (3) the hardness factor of various types of rock and cutting media. The latter is the particular phase of the subject discussed here. The cause of the confusion may be attributed partially to a lack of 'basic knowledge concerning the physical properties of the cutting media and of individual types of rock. It is also due in part to a general lack of uniform standards in the industry for evaluating the hardness versus drillability of rocks while possible errors in interpretation by the authors of the various papers pertaining to the subject may be an additional cause of misunderstanding. The hardness of a mineral is defined by Dana' as "the resistance which a smooth surface offers to abrasion." Webster' states that hardness is "the cohesion of the particles on the surface of a body (as a mineral) as determined by its capacity to scratch another or be itself scratched." Rock hardness, although not usually defined in publications describing rocks, is assumed to be the same as the minerals which compose the rock or the resistance of the rock to abrasion. Drillability of a rock may be defined arbitrarily as the rate at which rock is penetrated by a definite type of drilling tool with the assistance of a specific type of cutting surface or medium and under speci- fied conditions as to speed of rotation and applications of pressure. Eventually the term penetrability may have to be employed to include any method of making boreholes in rocks, since methods other than those using conventional cutting surfaces are already in operation. A case in point is the jet piercing methoda which employs an oxy-acetylene flame as a means of penetration. The word hardness as used by the drilling fraternity has a variety of meanings which depend upon the type of drilling method employed. For example, in diamond drilling, hardness is interpretated as resistance to abrasion. In percussion drilling the term implies resistance to impact or indentation, while in rotary drilling, hardness is considered anal-agous to compressive strength. The three types of hardness—abrasion, impact and compression—are conflicting variables for different types of rock. Nevertheless, the term hardness is applied indiscriminately by the industry for the resistance of rock to penetration by any type of drilling technique. Abrasion Hardness Since 1818, Moh's scale of hardness, although only relative in nature, has been accepted universally as the method of measuring mineral and therefore rock hardness. In 1933, Ridgway, Ballard and

Jan 1, 1952

By Newell Alford

AT its meeting in the fall of 1937, the Executive Committee of the Coal Division considered the growing scarcity of young engineers entering coal mining with serious intentions. This scarcity was the cause of con-siderable alarm and a committee consisting of C. T. Hayden, E. A. Holbrook, C. E. Lawall and L. E. Young, with the writer as chairman, was appointed to gather factual data on the current trend. A questionnaire1 was designed and mailed to the heads of the 60 mineral technology schools listed by Prof. W. B. Plank in his article in September 1937.2 Replies were received from 46 institutions, not all from heads of coal-mining courses but all from men that at one time or another have had experience with some kind of coal-mining curricula and know current student impressions. Our committee is indebted to all of these gentlemen for their cooperation. Our committee hoped by this means to quickly reach the root of the trouble and make a set of comprehensive recommendations to the Coal Division for relieving the industry immediately from the growing dearth of youth who yearn for coal-mining careers, but the condition is more serious than at first diagnosed. We must now refer the question back to the Coal Division, with the recommendation that the Division get the industry's permission for still another major operation on its frame of mind. In addition to 10-year statistics on the first pay received by graduates in coal mining and other technical work, we requested enrollment data for 20 years from all schools with either mining engineering or mineral technology curricula. Nine leading questions were also plied, as shown in the Appendix. Every one of the answers was significant and inter-esting. Fortunately, we encountered positive frankness that was extremely helpful.

Jan 1, 1938

BRADEN, the most southerly of the three big Porphyries in Chile and the first to start production (in 1910), is a remarkable mine. It would be interesting to know just how much it has contributed, and will contribute, to the earnings of the Kennecott Copper Corporation, which acquired 95 per cent of Braden stock in 1915 by an exchange of shares and which subsequently obtained the remainder. Because of this complete ownership no separate annual report is published (as is the case with Anaconda's South American subsidiaries, Chile and Andes). Income, taxes, operating costs, earnings, and other financial data, including the balance sheet, are consolidated with corresponding items applying to Kennecott's manifold operations in the United States and other foreign countries. If Braden were in the United States it would be possible to arrive at a pretty accurate estimate of revenue realized each year from the sale of copper simply by applying the average published market price to the production as reported by the company. However, because of the restrictions on sales imposed by the Chilean Government and the almost fantastic regulation of exchange rates in the past, no estimate of the sort would be reliable. This point is illustrated by the following comparison made by Charles R. Cox, president, in Kennecott's report for 1955: In each year, 1954 and 1955, Braden supplied about 30 per cent of Kennecott's total copper deliveries; but Braden's operations contributed 16.7 per cent of consolidated net income in 1955 against only 6.2 per cent in 1954. More will be said later about exchange rates, taxes, and restrictions, and the recent improvement in the situation. Of course another element of

Jan 1, 1957

By K. K. Rao, M. E. Nicholson

IN a recent paper on the solubility of carbon in Ni-Cu alloys,' Nicholson reported that the carbon solubility appeared to be limited by the electronic structure of the alloys and that the solubility was propor- tional to the density of states at the Fermi surface of the "3d" band. In order to determine whether or not this relationship is a general one, the study has been extended to other systems. One of these is the CO-Ni system. This system was chosen for study because 1) it is adjacent to Ni-Cu system in the periodic table, 2) the alloys of cobalt and nickel do not form stable carbides at 1000°C, and 3) the system exhibits no pronounced change (less than 1 pct) in lattice parameter from cobalt to nickel,' see Fig. 1. The alloys were prepared from -200-mesh 99.92 pct Ni furnished by the International Nickel Co. and spectroscopically pure -200-mesh cobalt sponge obtained from Johns on-Matthey and Co. The powders were weighed, mixed, and pressed using a pressure of 40,000 psi. The samples were sintered for 24 hr at 900° C in dry hydrogen and then cold rolled to a thickness of 0.010 in. (Samples containing more than 70 wt pct Co had to be annealed after cold reductions of about 20 pct to avoid cracking.) The alloys were carburized at 1000°C in an alun-durn boat containing Acheson AUC powdered graphite in an atmosphere of carbon monoxide cylinder gas which had been passed through Ascarite to remove carbon dioxide. After carburizing for either 12 or 24 hr the samples were moved to a cool zone of the furnace to cool. Cooling required about 5 min. The samples were filed to remove about 0.005 in. from the surface and then analyzed using a conventional combustion-gravimetric analytic method. The results of this investigation are shown in the lower portion of Fig. 1 and Tabulated in Table I. The nickel percentages for these alloys were determined from the weights of the powders from which the alloys were made. The solubility of carbon in pure cobalt at 1000°C (fcc) is 0.25 wt pct. This is somewhat less than the 0.33 wt pct measured by Boecker.3 From his data, it would appear Boecker's samples were supersaturated before the equilibrating treatment and that a 20-min treatment was not long enough to achieve equilibrium. Since in the present investigation the 12 and 24 treatments produced essentially equal carbon contents, our figure is presumed to represent more nearly the equilibrium value. The solubility of carbon in nickel of 0.19 wt pct agrees quite well with the value of 0.21 wt pct

Jan 1, 1963

By Floyd Kelley

THERE is an ever-increasing demand for furnaces with controlled atmosphere, due to the large quantities of steel being used in the automotive industry, such as the .high-chromium stainless irons, the 18 Cr, 8 Ni stainless iron and low-carbon steel sheets. The difficulties involved in the annealing of such materials, if they are to be kept absolutely free from oxidation, are many. It is possible to bright-anneal these steels in small laboratory hydrogen furnaces, using specially purified hydrogen and taking some additional precautions. In the first place, the insulation, usually of alumina or magnesia, holds small amounts of water vapor, which it is almost impossible to remove completely. Secondly, there is always condensation of water vapor in the cooling chambers of such furnaces, and with the continuous circulation of the hydrogen gas in the furnace, the water vapor is carried from the cooling chamber back into the heating chamber. This water vapor oxidizes the charge. Lastly, the supply of moisture is made sure by the diffusion of small amounts of air from the atmosphere into the furnace against the pressure of the hydrogen. The oxygen combines with the hydrogen and forms more water. Under such conditions there is, little gained by using specially purified gas, because it becomes contaminated after reaching the furnace.

Jan 1, 1931

By John Jan

Iodine is a soft, lustrous, grayish-black non- metallic element with a density of 4.9. It is the least active of the four members of the halogen family. The other members are, in order of increasing activity, bromine, chlorine, and fluorine. Iodine is a solid at ordinary temperatures, while bromine is a liquid and chlorine and fluorine are gases. Iodine melts at 113°C and volatilizes at 184.4°C to a blue- violet gas with an irritating odor. It occurs in nature only as iodates and iodides or other combined forms. It was discovered by Bernard Courtois in France in 1811, who noticed its presence as an unknown substance in crude soda ash obtained from burning seaweed. Gay-Lussac recognized it as a new element and named it iode, from the Greek word "ioeides or iodes" for violet color (MacMillan, 1970). The world production is not known with any great certainty, but it is probably between 20 and 25 million lb per year, of which about 25% is consumed in the United States. Geology and Mineralogy Iodine compounds occur as a minor constituent as a mineral in the Chilean nitrate deposits and in solution in brines and sea- water. According to the U.S. Geological Survey, it is the 47th most abundant element in the earth's crust. The minerals lautarite, Ca (10,) (calcium iodate), and dietzeite, Ca, (10,) , (CrO,) , (calcium iodate-chromate) are found in Chilean nitrate deposits which are located in Antofagasta and Tarapach provinces on the eastern slope of the coast range in a desert area. Various brines contain iodine compounds. Seawater contains about 0.05 ppm of iodine and some seaweeds will extract and accumulate it up to 0.45% on a dry basis. Some coals in West Germany also contain iodine compounds. The known and potential sources of iodine reported in 1968 are given in [Table 1]. Iodine has been recovered from brines in Java, Indonesia, France, England, and the USSR. Iodine has also been recovered from seaweed in Ireland, Scotland, France, Japan, Norway, and the USSR. The indicated re- serves and future resources of iodine are large but have never been adequately measured. Analysis Iodine as the free element can be detected by the characteristic blue color it gives to a starch solution. Quantitatively it is determined as the free element by titration with standard thiosulfate solutions using starch as an indicator. Colorimetric methods are also applicable.

Jan 1, 1975

By B. Egeberg, H. B. Smith

Britannia metal is a white alloy consisting primarily of tin and antimony, the tin greatly predominating. The alloy usually contains a small amount of copper and occasionally very small amounts of one or two other metals, such as bismuth, zinc, and lead. It is capable of being cold-rolled, it takes a high polish, and it is fairly noncorrosive; properties which make it a popular metal for many household and traveling utensils. Britannia metal is similar in many respects to pewter and has largely replaced pewter in the arts, but it should not be confused with that alloy, because pewter is essentially a tin-lead alloy, while Britannia is a tin-antimony alloy. In view of the fact that so little has been published concerning Britannia metal, the authors feel justified in presenting the results of their investigation, particularly since the behavior of this alloy under cold rolling and heat treatment differs so greatly from that of other metals and alloys. The old craftsman, engaged in the making of ornaments or tableware, heated the cold-rolled sheet metal or his finished product to a straw color corresponding to about 375" I?., claiming to produce thereby a harder and more rigid article. The fact that possibly led him to this heating was that a reheated article or sheet made from Britannia metal has a distinct metallic ring when struck a sharp blow, whereas an unheated article or sheet has a leady, dead note. No doubt he has associated the metallic ring with a greater rigidity and strength, and justly so, as will be seen later. The approximate analysis of the metal we investigated was 91 Sn, 7 Sb, 2 Cu, and the molten metal was bottom-poured into an iron mold yielding an ingot 7 3/4 in. wide by 11 in. long and % in. thick, the casting temperature being 800" F. The ingot was cold-rolled to a sheet 0.032 in. thick, sufficiently large samples for experimental purposes being cut from the sheet at intermediate stages. The samples were all tested for hardness with scleroscope and Brine11 machine, then heated to 212" F. for 30 min., and again tested after cooling to room temperature. The same samples were heated successively at 300°, 400°, and 440" F., followed

Jan 1, 1929

By H. B. Smith, B. Egeberg

Britannia metal is a white alloy consisting primarily of tin and antimony, the tin greatly predominating. The alloy usually contains a small amount of copper and occasionally very small amounts of one or two other metals, such as bismuth, zinc, and lead. It is capable of being cold-rolled, it takes a high polish, and it is fairly noncorrosive; properties which make it a popular metal for many household and traveling utensils. Britannia metal is similar in many respects to pewter and has largely replaced pewter in the arts, but it should not be confused with that alloy, because pewter is essentially a tin-lead alloy, while Britannia is a tin-antimony alloy. In view of the fact that so little has been published concerning Britannia metal, the authors feel justified in presenting the results of their investigation, particularly since the behavior of this alloy under cold rolling and heat treatment differs so greatly from that of other metals and alloys. The old craftsman, engaged in the making of ornaments or tableware, heated the cold-rolled sheet metal or his finished product to a straw color corresponding to about 375" I?., claiming to produce thereby a harder and more rigid article. The fact that possibly led him to this heating was that a reheated article or sheet made from Britannia metal has a distinct metallic ring when struck a sharp blow, whereas an unheated article or sheet has a leady, dead note. No doubt he has associated the metallic ring with a greater rigidity and strength, and justly so, as will be seen later. The approximate analysis of the metal we investigated was 91 Sn, 7 Sb, 2 Cu, and the molten metal was bottom-poured into an iron mold yielding an ingot 7 3/4 in. wide by 11 in. long and % in. thick, the casting temperature being 800" F. The ingot was cold-rolled to a sheet 0.032 in. thick, sufficiently large samples for experimental purposes being cut from the sheet at intermediate stages. The samples were all tested for hardness with scleroscope and Brine11 machine, then heated to 212" F. for 30 min., and again tested after cooling to room temperature. The same samples were heated successively at 300°, 400°, and 440" F., followed

Jan 1, 1929

By William McCullouch

The method of determining moisture percentages in coal has been defined as purely empirical. The procedure, as defined, has been published in the U.S. Bureau of Lanes technical papers and approved by the American Society of Testing Materials but deviations from this established procedure are common in most commercial and private laboratories. It is not within the scope of this paper to discuss the deviations in common practice but rather to give a detailed account of the method in use in the laboratories of the United Electric Coal Companies. In general, moisture values are presented as surface moisture and, for lack of a better term, inherent moisture. The formula for adding them together to give total moisture is common knowledge. In practice, on high-moisture bituminous coal, it has been found that the line of demarcation between surface and inherent moisture is very indefinite, the inherent moisture being so loosely held that it is released far beyond its natural limits when the prescribed method of the A.S.T.M. for determination of surface moisture is followed. This is shown in Table 1 for two typical washed coals from Illinois.

Jan 1, 1938

By P. T. Carter, A. B. Murad, H. B. Bell

The distribution of manganese and oxygen between molten iron and FeO-MnO-SiO2 slags not saturated with SiO2 has been determined and used to calculate activities of MnO and SiO2 in MnO-SiO2 slags. These were found to be intermediate between the corresponding activities in FeO-SiO2 and CaO-SiO2 slags. THE equilibrium constant for the reaction between molten iron containing manganese and slags containing FeO and MnO, namely: FeO(slag) + Mn = MnO (slag) + Fe(1iquid) is most conveniently represented by: (MnO) Kmn== (FeOHMn] [Fe] is omitted, since for dilute solutions of manganese in iron, afe is approximately constant. When activities are used for (MnO), (FeO) and [Mn], Kmn is a true equilibrium constant and will apply to all types of slags, but when weight percentages are used, the values obtained for Kmn for different slags vary considerably. The equilibrium between iron containing manganese and relatively pure FeO-MnO slags has been investigated by several workers;1-4 the most recent investigation reported is that of Chipman, Gero, and Winkler.4 Their results, corresponding to slags containing up to 4 pct SiO2, were represented by the equation: 6440 log KMn = +2.95 In this case both slag and metal may be assumed to be ideal solutions, therefore the values of Kmn so derived represent the true constant for the manganese reaction. As the molecular weights of MnO and FeO are almost equal, weight concentration of these oxides may also be used in the above expression. Acidic oxides such as SiO2 and P2O5 affect the activities of FeO and MnO differently, so that when total concentrations by weight of FeO and MnO are used in the above expression for Kmn the values obtained are no longer constant. These will be denoted by K'mn. Körber and Oelsen5 investigated the manganese reaction using silica-saturated iron-manganese-silicate slags and found: 7940 logK'mn =3.172 This corresponds to Kmn values much higher than those obtained for pure oxide slags. The results of Körber and Oelsen, and Chipman, Gero, and Winkler are summarized in Table I. In the present investigation it was decided to study the manganese reaction using iron-manganese-silicate slags not saturated with silica, and which fell mainly between the orthosilicate join 2FeO . SiO2 - 2MnO.SiO2 and the FeO-MnO side of the ternary system FeO-MnO-SiO2. It has been shown" that the phases present in solidified slags of this part of the diagram are (FeO, MnO) and (2Fe0.Si02, 2Mn0-SiO,) solid solutions. Such an investigation would be of interest in deoxidation and also gives information on activities in liquid slags. This equilibrium has not as yet been investigated successfully. Hilty and Crafts7 attempted to examine this reaction in a rotating crucible furnace, but were unable to obtain suitable slag samples. In the present investigation one series of experiments was carried out in a rotating crucible furnace, because the success of Taylor and Chipman8 with such a furnace in their study of oxygen distribution between molten iron and (CaO, MgO) — FeO-Si0, slags suggested that it would minimize contamination of the slag by the crucible material. A second series was carried out using a wire-wound resistance furnace. Rotating Crucible Furnace Experiments In all cases the metallic charge consisted of 800 to 1000 g Armco iron containing 0.02 pct C, 0.03 pct Mn, and traces of Si. Manganese and silicon additions consisted of electrolytic manganese (99.9 pct)

Jan 1, 1953

By J. Poijärvi, J. Rastas

Recently, when increasing attention has been paid to mercury for environmental reasons, the interest of several plants is directed to the removal of mercury from roaster and smelter gases. When Outokumpu Oy built its zinc plant at Kokkola in 1969, intensive development work was started to find an efficient and economic method for mercury removal from roaster gases. A process was developed, after laboratory research and pilot plant tests, to eliminate and completely recover mercury from the roaster gases. The process was commissioned in 1970. The behaviour of mercury in the roasting process and several possible methods of removing it from gases are discussed in this paper. Theoretical investigations and empirical tests show that the removal of elemental mercury from gases by sulphatization is very efficient. Further, it is stated how the technical process was built on this idea. The zinc sulphide concentrates contain small quantities of selenium, chlorine and fluorine. The role of selenium in the process is described. Similarly, the behaviour of chlorine and fluorine in the roasting, sulphatizing and scrubbing units has been discussed. Finally, the recovery of purified mercury and selenium from the precipitates is described.

Jan 1, 1973

By George H. K. Schenck, Peter G. Donald

There is an accelerating acceptance of change by management of cement companies. Diversity of response is noticeable in efforts across the country to reverse the downward trend in profits that brought margins in 1966 to the lowest point in 20 years. New concepts are emerging among managers as they seek to increase the efficiency in use of the basic corporate resources of men, capital and technology. The shift towards computerized control of cement manufacturing is making new gains as is diversification of cement companies into allied fields such as production and sale of natural and light- weight aggregates, crushed stone and concrete products. Increased interest in special products such as white cement and further moves overseas are also significant. Perhaps the most dramatic event of recent years occurred in Washington at hearings before the Federal Trade Commission where cement producers split on whether there should be FTC guidelines that would prevent ownership of ready-mixed concrete producers by cement companies.

Jan 4, 1967

By PAUL P. ZElGLER

Rapid growth of the aluminum industry continued through 1948 with an acute shortage of the metal in all forms marking the year. Estimates based on shipments made during the first nine months indicate that, in 1948, the industry shipped more than two billion pounds of aluminum products or roughly four times the amount shipped in the greatest peacetime year prior to the war. The rapid expansion of the aluminum industry is particularly reflected in the production of sheet. Last year, the industry as a whole shipped an estimated 40 per cent more sheet than was produced in the peak war year of 1944.

Jan 1, 1949

By George H. Hanna

THE importance of the Donets coal field (the Donbas) to the national economy of the Soviet Union is well known. Great as was the significance of this tremendous deposit of coal in prewar days it is destined to become an even greater factor in the economic life of the country now that the tremendous havoc wrought by the Germans is being remedied. Since the war began, new coal fields have been extended; for example output of the Moscow and Karaganda (Kazakhstan) fields has become considerably larger while new mines are producing coal in several parts of Uzbekistan and Kirghizia. The huge West Siberian coal field, the Kuznetsk Basin, is producing more coal than ever before to supply the industries of that region and of the Urals. But so great has been the development of industry to meet war needs, especially in those districts of the Soviet Union that lie to the East of the Urals, that the coal obtained, eked out by such locally-won fuels as peat and wood, is still barely sufficient to meet industrial requirements. The main burden of the coal supply for the restored industries of the West, therefore, will fall on the Donbas.

Jan 1, 1945

By George Rupp

THE Sunrise iron mine of The Colorado Fuel and Iron Corporation is in Platte County, Wyoming, about 110 miles north of Cheyenne. It is served by the company-owned Colorado and Wyoming Railway, which connects with the Chicago, Burlington and Quincy and the Colorado and Southern railways at Guernsey, Wyoming, a distance of 6 miles from the mine. The original Sunrise claims were staked mainly by United States Army officers and soldiers stationed at old Fort Laramie, because of small showings of copper in the Carboniferous limestones that form a horizontal capping overlying the Huronian iron ore. A small copper smelter was operated for about three years at Fairbanks, now an aban-doned town on the North Platte River. As many of the copper shafts and test pits near the present Sunrise mine were deepened, they pene-trated the capping and encountered iron. ore or gray sericitic schist, and were abandoned. Evidence of an early interest in iron ore was found when the Chicago claim was stripped for mining. A narrow, winding crevice was dis-covered, which led downward 20 ft. through the capping to the underlying soft red hematite, in which a room 10 by 14 by 7 ft. had been excavated. Stone hammers and wedges and a few rusted pieces of iron were found on the floor, and the evidence is conclusive that the excavation was used up to rather recent times by Sioux Indian medicine men, to provide war paint.

Jan 1, 1939

By John E. Greenawalt

IN view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by combustion within the mass itself. Its first successful application, in connection with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverberatory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremendous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blown off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for igniting purposes. Broadly speaking, sintering is an oxidizing or burning process, therefore the volume of air passing through the charge is the all-important factor. The air must pass through with sufficient rapidity to produce the necessary heat, and if sufficiently rapid the combustion will take place

Jan 1, 1938