Search Documents

By Earle E. Schumacher, W. C. Ellis

Nonferrous alloys upon which desirable properties can be conferred by heat treatment are becoming of increasing industrial importance. The alloys of copper with a constituent which has a solubility varying with temperature are materials of this character. Some of the constituents which are effective in producing a change in the mechanical properties of these alloys upon heat treatment are, according to Corson,' nickel and silicon, iron and silicon, cobalt and silicon, and chromium and silicon. In addition to these elements, Gregg2 states that the combination of beryllium and silicon is effective in producing age-hardening characteristics in copper. The effect of these elements, however, as dispersion-hardening constituents in the copper alpha solid solutions does not seem to have been studied in any considerable detail. This paper deals with the heat treatment and properties of three alpha brasses containing 3 per cent. of nickel plus silicon in the proportion necessary to form the compound nickel silicide, Ni2Si. Some information of a preliminary nature in regard to the hardening by heat treatment of phosphor bronze containing the same percentages of nickel and silicon is included. The method of hardening the alloys, which is effective in increasing the tensile strength and proportional limit, is similar to that used in the case of duralumin type aluminum alloys. It consists of a quench from a temperature at which the hardening constituent is in solid solution, followed by an aging at a lower temperature to precipitate the dissolved constituent in a dispersed condition. This results in an increased resistance of the alloy to deformation with an attendant improvement in the tensile properties.

Jan 1, 1929

By W. C. Ellis

NONFERROUS alloys upon which desirable properties can be conferred by heat treatment are becoming of increasing industrial importance. The alloys of copper with a constituent which has a solubility varying with temperature are materials of this character. Some of the constituents which are effective in producing a change in the mechanical properties of these alloys upon heat treatment are, according to Corson,1 nickel and silicon, iron and silicon, cobalt and silicon, and chromium and silicon. In addition to these elements, Gregg2 states that the combination of beryllium and silicon is effective in producing age-hardening characteristics in copper. The effect of these elements, however, as dispersion-hardening constituents in the copper alpha solid solutions does not seem to have been studied in any considerable detail. This paper deals with the heat treatment and properties of three alpha brasses containing 3 per cent. of nickel plus silicon in the proportion necessary to form the compound nickel silicide, Ni2Si. Some information of a preliminary nature in regard to the hardening by heat treatment of phosphor bronze containing the same percentages of nickel and silicon is included. The method of hardening the alloys, which is effective in increasing the tensile strength and proportional limit, is similar to that used in, the case of duralumin type aluminum alloys. It consists of a quench from a temperature at which the hardening constituent is in solid solution, followed by an aging at a lower temperature to precipitate the dissolved constituent in a dispersed condition. This results in an increased resistance of the alloy to deformation with an attendant improvement in the tensile properties.

Jan 1, 1929

Jan 1, 1966

By R. O. Burt

The economics of recovering slimes by gravity concentration, except in a few highly specialized cases, was hampered by the lack of suit- able high capacity equipment. However, in the last decade increasing cost of power and reagents, coupled with the development of high capacity units, has led to a reappraisal of the benefits of slime gravity concentration. This paper seeks to analyze the merits of gravity concentration, and the constraints placed upon it by the laws of motion. It traces the recent developments of unit processes, and their application to a wide range of minerals. The economics of gravity concentration are also discussed.

Jan 1, 1980

By H. D. Peterson, G. E. Butts, J. F. Spisak

In 1978, Anschutz Mining Corp. began efforts to develop the Madison Cobalt Project in southeast Missouri. Preliminary metallurgical studies indicated that intermediate grade cobalt products, suitable for shipment to existing refineries, could be recovered from the sulfide mineralization of the ore body. However, tolling and freight charges were significant, as the refineries were located outside the US. These refineries would not satisfy the goal of strategically insulated production of superalloy-grade cobalt. The acquisition of proven, readily available refinery technologies was then evaluated. However, licensing costs were substantial and the "proven" technologies were not directly applicable to the unique chemistry of Madison materials. Faced with these challenges, Anschutz, in conjunction with the Colorado School of Mines Research Institute, embarked on an effort to develop a sulfate-based separation and refining process. CSMRI performed bench-scale and continuous pilot experiments on solutions generated through other pilot campaigns conducted by Lurgi, Hazen Research, and Sherritt Gordon. The results indicated that cobalt could be selectively extracted from sulfate media using a new generation of organophosphates. The solvent extraction system produced a solution suitable for electrolysis of high-purity cobalt. Preliminary cost studies indicated the novel process was competitive with other refinery systems. Plans to develop the detailed engineering-design information required to commercialize the process were abandoned when the price of cobalt collapsed to less than $17.64/kg ($8.00 per lb).

Jan 1, 1985

By S. H. Ward, R. A. Barker

THE Juniper Prospect is in Carleton County, N. B., at approximately 46" 31' north latitude, 67" 20' west longitude. During the summer of 1955 an area in west-central New Brunswick was selected for aerial electromagnetic prospecting with American Metal Co.'s helicopter-mounted equipment. Generalized, small-scale government geologic maps had suggested that this area was located along the western border of the northeast-trending granitic backbone of northwestern New Brunswick and might be underlain by the Ordovician-Silurian sediments and volcanics that are the host rocks for the recently discovered sul-fide deposits of the Bathurst-Newcastle district. The helicopter electromagnetic equipment located an anomalous conductive area, coincident with a small aeromagnetic closure, about five miles west of the town of Juniper. Subsequently 30 mining claims (total area about 6600 x 8000 ft) were staked and company personnel conducted geological, geophysical, and geochemical investigations on the property. The claims and immediately contiguous areas were mapped geologically, and an area of about 2000 x 4000 ft was soil-sampled and also surveyed by ground electromagnetic and gravity methods. Finally six diamond drillholes, totaling 3500 ft in length, were drilled to test the anomalous conditions discovered by the several exploration techniques used. The discovery of base metal sulfides during drilling was a technical success for the exploration methods, but the quantity of sulfides was too small to be profitably exploited.

Jan 1, 1959

By AIME AIME

M R. WEIGEL'S present position as Chairman of the Institute's nonmetallics group arises from twenty years of experience in that field, from 1921 to 1926 as mineral technologist for the Bureau of Mines, in Washington, and since then for the Missouri Pacific R.R. Co., with headquarters in St. Louis. This rail- road serves an extensive region in and about the southern central states, from Omaha to the extreme southern tip of Texas, and from southern Illinois to Pueblo, Colorado, and it is Mr. Weigel's job to get as much freight for the road as possible from the mineral industry in this area. Much of the present and potential mineral production is in the non- metallic group.

Jan 1, 1940

By F. A. Howard, R. T. Haslam

In a broad sense automotive fuel is simply fuel in general and includes coal, coke, wood, charcoal and gas, in addition to the full range of liquid combustibles. All of these are actually used, or have been used, commercially to some extent as fuel for automotive vehicles. The steam lorry burning coal and coke is a common sight on the roads of England. The fact that these coal-fired steam lorries have a distinct advantage in taxes over the conventional gasoline-driven lorry probably explains the survival of this vehicle. The omnibus, or charabanc, operated by city gas carried in a balloon container on the roof, was also at one time a common sight in England, although not as common as the ubiquitous steam lorry. These gas-operated vehicles have, however, disappeared from the streets in recent years, and probably owed their existence entirely to war conditions. In France one of the largest motor vehicle manufacturers had last year more than 30 trucks equipped with regular gasoline engines in service in the Parisian area operating on producer gas obtained from a small gas producer mounted on the running board of the truck. Both wood and charcoal have been used in these gas producers. The authors were interested enough in this unique commercial development to spend some time examining the apparatus used and inquiring into the success which it had met. The picture is by no means an impossible one purely from the standpoint of practicability, but there is no doubt of the soundness of the conclusion that this is not a development which has any present important significance. Powdered carbonaceous matter, coal, coke or lignite, has been used experimentally in special forms of internal combustion engines, but so far as is known, these have never been applied to automotive practice. Range of Liquid Combustibles In the field of liquid combustibles the full range has been exploited to some extent. Heavy residual fuel oils from petroleum have been

Jan 1, 1928

By K. H. Coats, M. H. Terhune

Analysis and example applications have been performed to compare the accuracy and computing speed of alternating-direction explicit and implicit procedures (ADEP and ADIP) in numerical solution of reservoir fluid flow problems. ADIP yields significantly greater accuracy and requires about 60 per cent more computing time than ADEP, not 300 or 500 per cent more as reported elsewhere. l,2 INTRODUCTION Several recent papers 1-3 discuss an alternating-direction explicit difference approximation (ADEP) to the diffusion equation. Example applications of ADEP and ADIP4 were reported to support conclusions that ADEP is comparable in accuracy to ADIP and requires one-fifth to one-third the computing time of ADIP. Applications of ADEP in calculation of two-phase flow in reservoirs was also proposed. 3 This study was performed to compare further the relative merits of ADEP and ADIP in simulation of two-dimensional flow of one and two fluid phases in reservoirs. Since two-phase flow equations are often essentially elliptic rather than parabolic, the efficiency of ADEP in solving the elliptic equation was also examined.

Jan 1, 1967

By G. F. Tagg

Earth-resistivity measurements are often of service in obtaining information regarding geological formations, particularly when applied to structural problems. In such problems the masses of the various bodies are large, and have a corresponding effect on the average resistivity of the soil. Much work has been done using such measurements, but in general the method of interpretation employed is empirical. Since certain simple cases can be investigated mathematically, it appears to be quite sound to endeavor to apply the mathematical solutions to the practical results, in order to deduce from the latter such unknown quantities as depth. This paper deals with such a method of interpretation for the simple case of a single horizontal stratum. In the method described by Wennerl for measuring earth resistivity, four stake electrodes are driven into the earth in a straight line as shown in Fig. 1. A current I amperes is passed between the two outer stakes and the potential difference V volts between the two inner stakes is measured. Then if a is the electrode separation, the specific resistance of the soil, which is assumed to be homogeneous, is given by the formula P = 2?v/1 [1] v or if v/1 is called a resistance R ohms, p = 2?aR [2] If a is in inches, p will be in ohms per inch cube, or ohm-inches, and if a is in centimeters, p will be in ohms per centimeter cube or ohm-centimeters. As stated above, this formula is true only if the earth is homogeneous, and when this is not the case an application of one of these formulas

Jan 1, 1934

By Harold Vance

EMPLOYERS of engineers have not always been satisfied with the training that young graduates have received in the conventional four-year course. Specifically, employers of petroleum engineers for a number of years have believed that a four-year course does not allow sufficient time for the student to secure a fundamental engineering background plus the fundamentals of petroleum engineering. A group of California employers went so far as to set up a type of curriculum for a petroleum-engineering course, which was based on four years of undergraduate work and one year of graduate work, with most of the petroleum-engineering courses included in the graduate year.

Jan 1, 1944

By A. L. Holley

THOSE who are familiar with working gas furnaces will perhaps admit that the ordinary producer is the least satisfactory feature of the- whole system, chiefly by reason of its great waste of fuel, both above and below the fire. The waste of fuel in cleaning the fire has not, as far as I am aware, been carefully measured ; it has been roughly estimated at various works as averaging twenty per cent. to twenty-five per cent. The coke that falls into the ash-pit is largely mixed, if not stuck together with clinker; when this coke is not recovered and utilized (and where coal is cheap it does not pay to recover it), the waste is certainly as high as above estimated. Cleaning a fire on a grate (especially a fire of dirty coal, like much of our Western coal), by inserting a few temporary grate-bars, then withdrawing the regular grate-bars and letting the whole lower part of the fire tumble into the ash-pit, must necessarily be wasteful of fuel, but it has been found to be the most practical system. The fire under a boiler should be thin, to insure perfect combustion; hence it may be moved from one side to the other, so that .the clinker and ashes may be uncovered and removed. But a producer fire should be so thick that carbonic oxide only shall rise from it ; a thick fire cannot be thus manipulated. In several of the French works the ordinary producer without grates is employed ; the whole body of the fire rests on the floor of the ash-pit. It did not seem to me that less fuel was wasted here than with grates in cleaning fires. The bottom layer of the fire had to be drawn out with hooks, and there was nothing to prevent much coke from coming away with the clinker and ash. A producer shaped like a cupola furnace has many advantages, but if grates are employed the waste of coke in cleaning is not lessened. But the waste at the bottom of the fire is only a part of the waste in the ordinary producer. Mr. Emmerton, chemist to the Joliet Iron and Steel Company, has lately made a number of gas analyses from the producers of that company, worked with impure Illinois

Jan 1, 1880

By E. A. Beck

For a number of years many attempts have been made to use thermit in order to do away with piping in ingots. Some of these attempts were successful, while others did not give the expected results. Nearly every plant had its own method of using the thermit, and no special care was taken to study the results or to find the causes for lack of success. Formerly the principle of the process was to decrease the piping by introducing a can filled with thermit, attached to an iron rod, into the head of the ingot directly after it had been poured. In this case the thermit reaction took place in the upper part of the ingot, and it was thought that through the heat produced the head would keep liquid longer and piping thus be reduced. In other words, the aim was to keep the head of the ingot open by making use of the heat of the thermit reaction, which would thereby give the gases in the steel sufficient time to escape. This result can be attained by the application of a large enough quantity of thermit, but it would not be economical in general practice, and could only he used for high-grade material. Many steel-makers abroad and in this country have had this experience. The Th. Goldschmidt A. G., Germany, has, therefore, made a special study of this question with the cooperation of a well-known steel company, and has worked out a new method for the application of thermit for this purpose. The results obtained have been most satisfactory and reliable, and this process is now used in Germany on a large scale in many prominent steel-works. The thermit is applied in cans, as in former years, but the principle of the process is entirely different. The object of using the thermit is not to heat the steel and keep it liquid,

Jan 1, 1914

By F. W. Bloecher, A. M. Gaudin

THIS paper describes the results of a series of tests carried out to determine the partition of dodecylamine between distilled water and the surface of quartz at various concentrations of dodecylamine acetate in solution. An adsorption-column technique was utilized for this purpose. Ralston and Harwood, of Armour and Co., had synthesized marked dodecylamine acetate for us.' In their preparation which we employed, 0.0007 pct of the total carbon was the radioactive isotope, carbon fourteen. Unmarked dodecylamine acetate of high purity was also prepared by them for our use. The presence of carbon fourteen in the dodecylamine enabled us to analyze quantitatively for dodecylamine on the surface of quartz, using a radioactive-tracer technique. The method used was that known as internal gas counting of carbon dioxide, formed by oxidation of the amine. This method has already been described, "3 ' and the reader is referred to these papers for details of the analytical method and procedures. and surrounding liquor, a technique analogous to chromatographic columns was utilized. The experimental setup is shown in fig. 1. The dodecylamine-acetate solution was made up in a volumetric flask and poured into the glass funnel shown. It was allowed to drip slowly onto the quartz bed, the rate of flow from the funnel reser- voir being controlled by a hose clamp. The quartz column was contained in a small, fritted-glass filter (size 20 mm, C). The beaded top edge of the filter was cut off to enable the holder and contents to fit into the open end of the 30/45 joint on the combustion tube. This combustion tube is used in the analytical train described in a previous paper.' A piece of gum-rubber tubing joins the bottom of the fritted-glass filter to a filter flask, which in turn is connected to a vacuum line, or water aspirator. The rate of flow of amine solution through the bed was

Jan 1, 1951

By F. W. Bloecher, A. M. Gaudin

THIS paper describes the results of a series of tests carried out to determine the partition of dodecylamine between distilled water and the surface of quartz at various concentrations of dodecylamine acetate in solution. An adsorption-column technique was utilized for this purpose. Ralston and Harwood, of Armour and Co., had synthesized marked dodecylamine acetate for us.' In their preparation which we employed, 0.0007 pct of the total carbon was the radioactive isotope, carbon fourteen. Unmarked dodecylamine acetate of high purity was also prepared by them for our use. The presence of carbon fourteen in the dodecylamine enabled us to analyze quantitatively for dodecylamine on the surface of quartz, using a radioactive-tracer technique. The method used was that known as internal gas counting of carbon dioxide, formed by oxidation of the amine. This method has already been described, "3 ' and the reader is referred to these papers for details of the analytical method and procedures. and surrounding liquor, a technique analogous to chromatographic columns was utilized. The experimental setup is shown in fig. 1. The dodecylamine-acetate solution was made up in a volumetric flask and poured into the glass funnel shown. It was allowed to drip slowly onto the quartz bed, the rate of flow from the funnel reser- voir being controlled by a hose clamp. The quartz column was contained in a small, fritted-glass filter (size 20 mm, C). The beaded top edge of the filter was cut off to enable the holder and contents to fit into the open end of the 30/45 joint on the combustion tube. This combustion tube is used in the analytical train described in a previous paper.' A piece of gum-rubber tubing joins the bottom of the fritted-glass filter to a filter flask, which in turn is connected to a vacuum line, or water aspirator. The rate of flow of amine solution through the bed was

Jan 1, 1951

By P. B. Baxendell

The appraial of producing properties and profitability ntzalysis of a proposed capital expenditure are based on the same principles. In both problems a projection of future cash income is. cornpared to one or more capital expenditures. Several different methods have been in use either to compute a price to obtain a given earning power on the investment or to compute the earning power which will result from a given capital expenditure. One of these, the "Average Annual Rate of Return" method, computes in a simple manner the ratio of the present value of the future earnings after amortization to the present value of the undepreciated balances of the investment over the life of a project. This method, not well known generally, appears to have some rather unique advantages in reducing the computation work required, eliminating trial-and-error solutions, and providing a more accurate answer when applied to oil industry investments subject to the unit-of-production basis of amortization. Its derivation is given and its versatility demonstrated in the solution of certain everyday investment problems. A number of charts, useful in applying this method to profitability analysis and appraisal work, are provided. The current trend in the market values of producing properties is shown. INTRODUCTION Making sound capital expenditure decisions requires an objective means of measuring the productivity of individual investment proposals. Since the best measure of the economic worth of such proposals is their ability to produce profits, it is common practice to grade proposed capital expenditures according to their annual earning power as a percentage of the outstanding capital. The same principles which govern the determination of the rate of return of proposed capital expenditures also apply generally to the problem of determining the appraisal value or purchase price of income-producing oil and gas properties. Both problems are of prime importance in the producing phase of the oil business, where management is faced daily with decisions to drill or not to drill certain development wells, or with the determination of the appraisal value of producing properties. The common feature in both problems is that a projection of future cash income is compared with a known or estimated capital investment to determine itsiearning power or annual rate of return. In the case of development drilling, the cost of the proposed well can usually be estimated with a fair degree of accuracy and the problem consists of finding the rate of return on the invested capital. In the case of appraising producing properties, on the other hand, the desired rate of return is usually known in advance and the problem consists of determining the purchase price which, for the given income projection, results in the fequired rate of return. Certain accounting procedures common to the oil and gas producing business make these two problems and their solutions somewhat different from corresponding problems in other industries, and, in certain ways, simpler. The main difference is in the amortization policy which, for oil and gas production, is frequently on a unit-of-production basis, compared to the amortization on a time basis used in many other industries. The purpose of this paper is to discuss briefly the various methods currently in use for the measurement of productivity of invested capital in producing properties and, in more detail, the derivation and application of what will be called the "Average Annual Rate of Return Method". This rather interesting and not too well known method has some very definite advantages in the solution of many problems common to the oil industry. For the sake of simplicity, federal income tax considerations have been disregarded in the examples used, since they do not affect the principles involved. The use of the production payment route in the sale or purchase of producing properties, which has been amply covered in many other publications, has also not been included in this analysis. METHODS FOK MEASUKING THE EARNING POWER OF INVESTED CAPITAL, Of the many different methods used to measure the earning power of invested capital, four are applicable to oil or gas production ventures. Depending on whether these four methods utilize one or two interest rates, and whether a fixed amortization pattern is used, they may be classified as follows.

By G. S. Coe, G. F. Bolling

The columnar-to-equiaxed transition (CET) has often been studied as a function of concentration, C, temperature gradient in the melt, G, and rate of solidification, R. Although it may not be immediately obvious it is sure that the CET, expressed as some ratio G/R necessary to suppress equiaxed nucleation for a given C,' cannot be a single-valued function of C. This restriction which is ignored in theoretical presentations is most trivially illustrated by the following simple reasoning. An ordinary casting is an unconstrained system where the thermal conditions change continuously with progressive solidification, and thus where the ratio G/R decreases from the outset. A CET occurring early in a casting (much equiaxed material) must then mean a higher value of G/R at transition, in comparison with the late CET which implies a more columnar ingot. Therefore, when we choose to experiment under constant superheat for all alloys across the simplest binary, and we find an inversion in the amount of equiaxed material, we shall find two values of C satisfying the G/R condition. However, in addition to this simple instance, the early experiments of ~orthcott' seem to show that the amount of equiaxed material in cast ingots may be a multivalued function of composition in a given binary system. In the present investigation, the CET has been examined in Pb-Sb, Pb-Ag, Pb-Sn, and Sn-Pb under several types of casting conditions. First, we have used the "bidirectional" ingot section Simulation;~ and we have used .'i~z situ" ingot solidification where a hot mold already filled with liquid is chilled so that there is no disturbance provoked by pouring. Differences in method are trivial to our purpose except for the fact that certain variations are more simply observed by one technique than by the other. Second, we have varied the mode of superheating from the simple extreme of casting all alloys from the same temperature regardless of composition to the careful casting at a standard superheat, calculated with respect to the alloy liquidus. Third, we have made provisions for decanting and interface observation, so that some "castings" were not completed. The results obtained with Pb-Sb are exemplary; some of these are shown in Fig. 1 along with explanatory captions. At 9 to 10 at. pct Sb, and thus above the solid-solubility limit Cs = 5.8 at. pct Sb and yet below the eutectic concentration Ceu = 17.5 at. pct Sb, there is a persistent anomaly in all the variations. Measurement was easy enough and standard enough so that we may forgo discussion of either method or possible error, in view of the forceful self-consistency shown by experiment. Solute distributions were measured along the bidirectional ingots in order to determine if a solute buildup had occurred at the CET. No anomalous changes in concentration were observed along the bars at either side of the solute anomaly of 10 at. pct Sb. The microstructures of the ingots were also examined across the range of composition investigated. At concentrations less than 9 at. pct Sb the micro- and macrostructures were typical of the cellular-dendritic growth usually reported for the columnar zone. Above the anomaly, both the columnar grain size and the amount of primary phase decreased. This microstruc-tural observation can be correlated with observations made of decanted interfaces. Below 9 at. pct Sb, the interface reveals the "normal" columnar dendritic structure; however above the anomalous concentration range, preferential growth of certain dendrites appears to form a "super dendrite" pattern. In Fig. 2 a microstructural view of the etched '(super dendrites'' shows their constitution both in terms of relative phase proportion and in terms of the ordinary smaller dendrites.

Jan 1, 1969

By H. F. Silliman, Daniel R. Hull, John R. Freeman

In the normal operation of a brass-rolling mill, sheet and strip has, for the most part, been finished in comparatively thin gauges, involving a substantial amount of cold-work and a considerable number of anneals. This condition has been disturbed by the preponderance of cartridge brass, which is not rolled to thin gauges, and particularly by brass for artillery cartridge cases, on which the mill may finish its work at a thickness between 0.400 and 0.900 in. Obviously, the amount of rolling and the number of anneals to which such a product can be subjected are small compared with strip that is carried to a thickness of a few hundredths of an inch. As a result, critical examination into the internal condition of metal has been made on an extensive scale at a stage of manufacture that would not, in normal times, have been chosen for complete inspection. Under these conditions, a type of defect has been recognized that is not seen at thinner gauges. It might be more accurate to call it the appearance of a defect, since it refers to an apparently laminated, discontinuous structure, which, in fact, does not exist as such, and disappears after suitable treatment. For this reason it has been called a phantom lamination, which the authors consider an appropriate term. It is the purpose of this paper to describe the phenomenon and the conditions of its occurrence and, at least tentatively, to discuss its nature and cause. Great numbers of phantoms may be found in 2:r brass, either hot-rolled or cold-rolled. They are also found in 70-30 brass, sometimes when hot-rolled and generally when cold-rolled. It is not believed that phantoms are confined to these alloys but this paper is limited to them for the purpose of description. Hot-rolled 2:1 Brass For illustration, therefore, a typical cake of hot-rolled 2:I brass has been chosen. This was rolled to a slab 36 in. thick, from a casting 5 in. thick by 24 in. wide by 18 in. high, which was believed to have been sound. After hot-rolling and cooling, the slab was sheared and a portion of such a shear cut is shown in Fig. I. It would be difficult to convince anyone viewing this specimen that the metal was not unsound. The impression would be confirmed by the appearance of a tensile break, as shown in Fig. 2. This is an ordinary tensile-test piece from metal just described. Although there was nothing in its tensile strength or elongation that suggested unsoundness, it appeared run through with pipes and laminations. To question the reality of such a condition would imply questioning the obvious. But, considering the history of the metal, it would be difficult to believe that it could be so bad as it appeared. It seemed reasonable, though, that if the defects were what they appeared to be, they could be traced back from the sheared or broken face.

Jan 1, 1945

By E. A. H. Tays

As I promised, in a former paper on the Bryan Mill,* to give further data regarding the plates from four battery-aprons, I now submit the following: These aprons were 4.5 feet wide by 16 feet long; the first two plates of each apron were 4.5 by 4.5 feet, and the remainder of varying sizes, as can be seen by their relative weights, as shown in the table; but all were 54 inches wide. They were in use 4 years and 9 months, and about 15,265 tons of ore passed over each. The ore was quartz, carrying about the same weight in silver as in gold; showing some copper, and highly impregnated with ferric oxide. The tailings show about 0.6 per cent., and the bullion about 10 per cent., of copper. The silver was present mostly as sulphide; and the copper was also present as sulphide, with some carbonate. The ore treated ill 1898 was a fair average of the whole run; so I take it as an example from which to make a few deductions.

Jan 1, 1901

By Carl Trischka

During fifty-three years of mining operations in the Warren mining district, the mineralization has been found to cover an area roughly 2 miles long by 155 miles wide. Ore extraction from the richer portions of this area has been closely followed by surface subsidence. At the western end of the district, where the ore outcrops at the surface and oxidation is more complete over a wide area, intense surface disturbance is visible in the form of closely spaced open cracks and escarpments. As work has progressed toward the east, more unoxidized ore-bodies have been found and mining has been at increasing depth, for which reasons surface subsidence is less intense and subsidence blocks become larger and in general are bounded by open cracks, which persist over long distances. There may also be traced on the surface what appears to be a boundary crack, running in a northwest-southeast direction, marking the present southerly limit of subsidence of the district as a whole. It is not completely developed, and has not as yet appeared over the very deep mining operations in the extreme easterly portion of the district. Check surveys show that vertical and horizontal dislocation is still taking place. All of the various mining operations, including open-pit work in porphyry ore and underground mining of limestone replacement and porphyry ores, have had their influence in disturbing the surface. As these influences frequently overlap, and because the surface disturbance is continuous over practically all ore occurrences, it is virtually impossible to choose an area sufficiently isolated to ascribe the amount of subsidence to any definite volume of ore removed. After due consideration of all factors, there has been selected for discussion an area 1400 ft. long by 1200 ft. wide, which will be referred to as the Queen Hill block. It is bounded on all four sides by faults, which tend to limit subsidence disturbance to that caused by ore mined from within the block, and likewise to prevent subsidence cracks due to mining outside of the block from entering the area.

Jan 1, 1934