Search Documents

By C. Elbaum

Specimens consisting of several crystals, each with a prescribed geometry and a controlled orientation with respect to both the extermally intposed stress and the highboring crystals, werer deformed in tension at room temperature. It is shown that the influence of a grain boundary on the plastic defolrmation of a mullicrystal depends on the extent to which the presence of the grain boundary, contributes to the necessity 01. multiple slip in the component crystals. MANY investigations were carried out in the past on the plastic deformation of aluminum single crystals, bicrystals, and polycrystals. The various studies of bicrystals aimed primarily at elucidating the influence of grain boundaries on the mechanisms of plastic deformation. In the earlier studies the emphasis was placed primarily on finding the "strength" contributed by a grain boundary. In more recent investigations it became apparent that the grain boundary does not contribute any strength per se but rather acts by influencing the mechanism of plastic deformation in the adjoining grains. The concept thus emerged of the plastic properties of a bi-crystal, and by extension of a polycrystal. depending solely on the mechanism of deformation prevailing in each grain. The contribution of the grain boundaries thus becomes limited to the type of restrictions imposed on each grain by its neighbors. The present investigation of the behavior of specimens consisting of more than two crystals was designed for the purpose of studying the influence of the grain boundary in simple aggregates. The findings of this study further support the concept that the restriction imposed on a deforming crystal by its neighbor constitutes the predominant factor in the plastic deformation of polycrystals. The term "multicrystal", in contrast with single and polycrystals, is used to describe specimens consisting of several crystals. Each one of the component crystals has a prescribed geometry and a controlled orientation with respect to both the externally imposed stress and the neighboring crystals. Two groups of multicrystals were prepared. All the component crystals of both groups of multicrystals had the axial orientation (isoaxial multicrystals) shown in Fig. 2, with the primary slip plane and slip direction both at 45 deg to the specimen axis. In the first group (hereafter referred to as group I) the component crystals were symmetrically oriented with respect to the plane of the grain boundary; the primary slip plane and slip direction were respectively at an angle of 60 and 30 deg to this plane. For the second group (group 11) the axial orientation remained the same and the relative positions of the primary slip plane and slip direction are shown in Fig. 3. EXPERIMENTAL METHODS The material used was aluminum 99.993 pct pure, according to the manufacturer. The specimens were produced by growth from the melt in a horizontal graphite container. In order to maintain the prescribed geometry of the individual crystals of a multicrystal, a technique described elsewhere was used.' The specimens were grown under a small, positive pressure of helium at a rate of approximately 1 mm per min. annealed in air for 24 hr at 640°C and cooled over a period of several hours to room temperature. All the multi-crystals were rectangular in cross-section, 6 by 18 mm (see Fig. 1) and from 150 to 170 mm long. In each group bicrystals, tricrystals and quadru-crystals were prepared as shown in Figs. 1 and 4.

Jan 1, 1961

By H. D. Kessler, M. Hansen, R. J. Van Thyne

The phase diagram of the titanium-rich portion of the system Ti-Cr-Fe to 70 pct Ti was established by means of isothermal sections at 900°, 800°, 750°, 700°, 650°, 600°, and 550°C, using arc-cast alloys. An isotherm at 800°C was determined for the section bounded by Ti, TiFe2, and TiCr2. Micrographic analysis was employed as the principal method of investigation, supplemented by X-ray diffraction and incipient melting studies. A ternary eutectoid, ß ? a+ TiCr2 + TiFe, occurs at approximately 8 wt pct Cr, 13 wt pct Fe, and about 540°C. AMONG the first titanium-base alloys in commercial production were the Ti-Cr-Fe alloys. For this reason, the Materials Laboratory, Wright Air Development Center, sponsored an investigation of the system. No information on the constitution of the titanium-rich corner was available. Vogel and Wenderott studied titanium-poor ternary alloys.' As part of this program, the binary systems Ti-Cr and Ti-Fe have been determined previously by the authors.' Other investigators have also studied the binary systems Ti-Cr,3-7' Ti-Fe.³,8-10 Both of the binary systems are characterized by the eutectoid decomposition of the ß phase. Most of the effort of the present work has been concentrated on the titanium-rich corner with compositions of less than 30 pct total chromium and iron content. The determination of isothermal sections was the experimental approach used to obtain the ternary phase diagram. Vertical sections were used to check the consistency of the isothermal sections. While this investigation was in progress, a study of the Ti-Mo-Cr system at Armour Research Foundation disclosed the existence of a high temperature modification of TiCr2 above 1300 °C.11 This allotrope has a hexagonal structure of the MgZn2 type, iso-morphous with TiFe2, whereas the low temperature modification of TiCr2 is cubic," of the MgCu2 type. The existence of allotropy in TiCr2 of course means a more complicated set of phase relationships in this general region than if the phase were monomorphic, as was first assumed. Additional studies were made late in the investigation in order to clarify the part that the hexagonal TiCr2 phase plays in the ternary phase relationships. These will be discussed in a separate section. Because they are of greatest practical significance, the phase relationships in the titanium-rich corner will be presented first, omitting the equilibria involving the hexagonal modification of TiCr2 in an effort to simplify the presentation somewhat. Experimental Procedure Materials: The titanium used in the preparation of the alloys was iodide crystal bar (99.9 pct pure) produced by the New Jersey Zinc Co. High purity chromium and iron were obtained from the National Research Corp. Table I gives the analyses of these materials. Melting Practice: Over 100 alloy ingots weighing 10 to 20 g were melted in a nonconsumable electrode arc-melting furnace. As the techniques are identical to those reported previously,12,13 they will not be detailed here. The ingots were melted in the cavity of a copper melting block insert under a slight positive pressure of helium. No measurable hardness

Jan 1, 1954

By Carlos G. Valenzuela

The value generally accepted for stacking-fault energy, of copper has been approximately 40 ergs per sq cm based on Fullman's2 value for the coherent twin-boundary energy and the assumption that is twice the twin boundary energy However, Thornton and coworkers8 determined that the lower limit of for copper is approximately 60 ergs per sq cm, based on measurements of dislocation-node radii. They suggested that the assumption of = 2t is invalid. It is the purpose of this note to present results which indicate that the values of obtained by measurement of twin-grain boundary intersections and the values obtained by measurement of dislocation-node radii are actually compatible. The most reliable values for of the a brasses, based on electron-microscope observation of dislocation nodes, are probably those values reported by Smallman and Green6 who applied the Siems correction (1961) to data obtained by Howie and Swann.3 These values shown in Fig. 1 give an extrapolated value of approximately 70 ergs per sq cm for pure copper. In the present work, Fullman's method for determining the stacking-fault energy of copper was extended to the a brasses. High-purity copper (99.999 pet) and high-purity zinc (99.999 pet) were mixed in proportioned amounts and melted in sealed and evacuated quartz tubes. The alloys were homogenized for a week at 750°C and chemically analyzed by means of X-ray fluorescence. These alloys, along with a specimen of pure copper, were rolled to 98 pet reduction and a thickness of 0.009 in., resealed, and annealed for 40 hr at 715°C. Values for the ratio of twin-boundary energy to the grain-boundary energy, it gb, were obtained from measurements of dihedral angles formed at the intersections of twin boundaries and grain boundaries by using Fullman's2 mechanical analogy of surface tensions acting at the intersection of an annealing twin and a grain boundary. The angles between the twin traces and the grain boundaries were measured for a large number of twin-grain boundary intersections at a magnification of X500 using a rotating mechanical stage on a Reichert metallograph. The rotary stage has a calibrated angle scale with vernier so that measurements can be made to 0.1 deg. The mean twin-grain boundary energy and standard deviation were calculated for copper and each of the brasses by the use of an IBM 7072 computer. It was found that the mean value of gb stabilized after approximately 100 twin-angle measurements. This was determined by plotting the mean against the number of angles measured. Since the measured angles deviate from true dihedral angles, a correction factor for grain orientation, discussed below, was applied. The stacking-fault energy was then calculated from these values and the values of grain-boundary energy derived by Taylor.7 The data obtained are tabulated in Table I. Values for stacking-fault energy are plotted in Fig. 1. The value of gb for the specimen of 1.03 pet Zn is close to the value obtained by Fullman2 for OFHC (99.98 pet) copper, 0.045. It is believed that the purity of the copper affects gb significantly. The 99.999 pet purity Cu used in this investigation yielded a value of yt/ygb, 0.76, which is much higher than that obtained by Fullman. Additional evidence suggesting that the purity of

Jan 1, 1965

By J. W. Whalen

The design, operation and evaluation of an instrumental method for the determination of fluid saturation in porous materials during multiphase flow studies is described. The presence of a magnetic tracer comprising approximately 20 per cent by weight of the aqueous phase is necessary in the utilization of this method. The results of two-phase relative permeability studies on two samples of porous media are presented. The realizable accuracy of the magnetic susceptibility apparatus in fluid saturation determination is estimated to be 2 saturation per cent. The response characteristics of the instrument, together with its simplicity of operation and maintenance are sufficient to recommend its use in routine laboratory studies. INTRODUCTION The problem of fluid saturation determination in laboratory multiphase flow studies characterizing oil recovery processes is one which has been given exhaustive study. Briefly the requirements which are considered essential for a method sewing this purpose are: (1) that the measurement be made external to the porous rock sample under study with no interruption of the fluid flow pattern, (2) the saturation indication must be independent of fluid distribution in the volume scanned by the measuring device, (3) the sensing element should have a small field of definition enabling several independent measurements to be made along the length of a core sample, and (4) the properties of the fluid phases should not be too greatly influenced by required tracer substances. Several methods of saturation determination have found acceptance as meeting most of the above requirements. These include resistivity,1 X-Ray absorption,2,3,4 radiotracers,5,6,7 and neutron8 diffraction The merits of these techniques have been discussed elsewhere in detail and will not be considered here. It may, however. be pointed out that the elaborate instrumentation required by the methods mentioned above, with the exception of the resistivity method (which is undesirable from other standpoints) encourages the development of methods of saturation determination which, while meeting the requirements listed, are simple to operate and maintain. It is the purpose of this paper to describe the instrumentation and evaluation of a technique for the determination of fluid saturation which combines relative simplicity with an accuracy and applicability comparable with methods now in practice. DESCRIPTION OF THE METHOD If the magnetic susceptibility of one of the fluid phases contained within a porous material is sufficiently greater than that of the remaining phases, the fluid content of the material with respect to that phase may be determined by an induction measurement. This may be accomplished by measuring the induced voltage in the secondary of a transformer which contains the porous sample and its interstitial fluids as a portion of the magnetic flux path. Since the fluids used in multiphase flow studies involving petroleum reservoir samples possess uniformly low magnetic susceptibilities, the use of a magnetic tracer in one of the fluid phases is required. In view of the relatively high paramagnetic susceptibility of salts of the transition elements, together with their high water solubility. these compounds become logical choices as tracer materials. Cobaltous chloride, having a specific magnetic susceptibility of 17.5 x 106 cgs electromagnetic units, was used as the tracer material throughout this work, in a concentration of approximately 20 per cent by weight in the aqueous phase. MAGNETIC SUSCEPTIBILITY APPARATUS Basically, the magnetic susceptibility apparatus consists of a transformer serving as the detecting head, a

Jan 1, 1955

By Clark L. Corey, Bogdan Lisowsky

Electrical resistivity, X-ray line positions, degree of order, and microstructures have been investigated for Ni-A1 alloys near the Ni3Al composition. The results indicate that Ni3Al undergoes disordering between 1250oC and the mp; also supersaturated y, produced in y + y' alloys by gas quenching, is extensively ordered prior to y' (Ni3Al) phase separation. The latter reaction, if not both, must follow the cooperative phenomena model. Shifts in line position as a function of quench-indulced super satulration are shown. Lattice pavarneters of equilibriunz and nonequilibrium phases are given. THE objective of this investigation was to determine the mechanism and kinetics of the reactions which occur in Ni3A1 and hypostoichiometric Ni3A1 alloys. The results are of particular significance relative to pre-precipitation phenomena. Early work on Ni-A1 binary compositions near the Ni3A1 composition (13.6 wt pct Al) has been adequately reviewed by Hanssen,1 whose phase diagram is presented in Fig. 1. williams2 verified the suggestion made by Taylor and Floyd3 and others4 that y', Ni3A1, may precipitate coherently on (100) planes of the y phase (see Fig. 1 for phase nomenclature); he further suggested a two-step precipitation mechanism consisting initially of probably short-range ordering followed by actual precipitation of y'. The precipitation stage in low-aluminum hypo-eutectic compositions has been studied by a number of investigators;*"7 short-range order or "zone" formation have been suggested as explanations for various diffuse X-ray scattering effects. The ordering reaction in Ni3A1 alloys is characterized by a) a very rapid rate of ordering in nonstoi-chiometric compositions, b) absence of a disordered phase region for the stoichiometric compound, y', or Ni3A1, c) precipitation phenomena as a dominant aspect in hypoeutectic alloys, and d) an increase in elec-trical resistivity on ordering.' The latter two factors were found by Newkirk to characterize ordering in Co-Pt, for which an extensive and detailed analysis was made.' An electrical-resistivity increase on ordering has also been reported for cuAu3.10 PROCEDURE Ni-A1 alloys in the form of 1300-g chill-cast ingots were prepared by vacuum melting electrolytic nickel and high-purity (99.99 pct) aluminum. Very small heats prepared from high-purity carbonyl nickel, supplied through the courtesy of Dr. Goff of the Naval Research Laboratory, were used for comparison with the larger ingots and no differences were noted. The cast material was homogenized in purified argon for a minimum of 72 hr at 1200°C and water-quenched from 1350°C. Compositions studied are given in Table I. The 10 pct A1 alloy was both hot- and cold-rolled. X-ray superlattice line intensities and peak positions were obtained from -270 mesh filings, using CuK, radiation with a LiF crystal monochromat adjusted to receive both 01 and a2. One-degree slits and a 1/8 deg per min scan rate were used to record line traces. A standard tungsten powder, obtained through the courtesy of G.E. Research Laboratory, was used to calibrate line positions.

Jan 1, 1968

By W. E. D. Stokes

The application of aviation to mining and petroleum operations, on the basis of economy and attainment, has become a demonstrated fact. According to Dominion Government rccords, 30 Canadian companies engaged in air transportation with northland mining camps, carried 13,000 tons of freight in 1935, and in 1936 carried 16,000 tons. In addition, many mining companies used planes to transport prospectors with canoes, outboard motors, gasoline drums and supplies to remote locations, and one company maintained a plane to take radium-bearing ore from its mine on Great Bear Lake nearly 1000 miles south to the railway at Waterways, Alberta. Heavy pieces of mining machinery weighing 2 tons are being carried by Ford trimotor planes over the Andes, at an altitude of not less than 15,000 feet. At Bulolo, New Guinea, 17,500 tons of disassembled gold-dredging equipment has been flown over inaccessible terrain, while supplies and building materials for a community of 1000 whites have been transported by airplane. A 31/2-ton shaft was carried on one notable trip, while at another time an automobile, 2 tons of rice and a large safe went over the mountains in one plane. Fig. 1 shows an electric generator that was carried by plane to Bulolo. Many large American oil companies operated fleets of planes during 1936, ranging from fast, luxurious air liners for executives to elaborate geological prospecting units, ambulance planes, freight carriers and pipe-line repair crews. According to the U. S. Geological Survey, commercial firms photographed 16,291 square miles during 1935, while the Government compiled from aerial photographs by the Geological Survey in the United States 85,544 square miles. It was found that information could be determined in a fraction of the time required by surface methods. However, sounding a word of caution, a Commonwealth of Australia government report on aerial survey operations had this to say: It is necessary to repeat ad nauseam that aerial photographic survey is in no sense a substitute for geological investigation, though it is a very valuable adjunct thereto, and greatly facilitates and aceeleratcs geological mapping. There are many details

Jan 1, 1937

At a meeting of the Board of Directors, held Jan. 21, 1916, the following resolution was adopted: Resolved, that this Board has learned with indignation and sorrow of the unprovoked and brutal murder of 18 American citizens on January 10, in the State of Chihuahua, Mexico, and laments especially the death of Messrs. C. R. Watson, C. A. Pringle, H. C. Hase, and W. J. Wallace, who were members of the American Institute of Mining Engineers. As these men and their companies were engaged, in the lawful prosecution of their work, we trust that nothing will be allowed to prevent or delay appropriate action by our Government concerning the outrage by which they lost their lives;

Jan 3, 1916

By R. C. Ellman

In the United States, the consumption of lignite and subbituminous coals is increasing. A variety of energy-oriented companies have leased large blocks of reserves, new large power plants are in operation and being constructed, and new producing mines are being developed. The Bureau of Mines has maintained an active interest in the utilization of low-rank coals for many years. In 1951, with the completion of the Bureau's Grand Forks Coal Research Laboratory, an organizational unit was established for studies in lignite preparation. Since that time, numerous investigations have been completed. This research has dealt almost exclusively with lignite, but since subbituminous coals have many similar characteristics, the findings can often be applied to both types of coal.

Jan 1, 1970

By V 7. 0 / 300 dpi

THE cams at present universally used in stamp mills lift the tappets with an involute form of curve, to which the surface of the tappet is always tangent; moreover, the line of contact between tappet and cam, if produced, would pass through the center of the stem. This is no doubt a desirable feature, but the writer has long believed that it would be much more desirable if the cam were to pick up the stamp without shock, and gradually increase the upward velocity of the stamp throughout its upward movement. The involute form of cam attempts to impart instantly a considerable upward velocity to the stamp, starting it from a state of rest, and the result is a destructive blow, a great deal of noise, and much wear and vibration. The writer has developed a form of cam which will lift the stamp with a motion similar to that of the piston of an engine between the end and middle of its stroke; in other words, harmonic motion, from the point. of zero to maximum velocity. The curve will give this ideal motion only when the stamp is set for the exact drop for which the cam was designed, but the improved cam will not be as bad as the involute cam until the drop is reduced one-half. In other words, if a cam is designed for a 6-in. drop, it will be some improvement over the usual form of cam until the drop is only 3 in. Any cam, whatever its form, must of course lift the stamp in the same number of degrees of revolution; therefore, with this new form, since the stamp starts more slowly on its upward course, it must end up by going faster, the average speed being the same as with the involute cam. The stamp, after it is no longer in contact with the cam, keeps on going up a certain distance, which is easily calculated. It is therefore possible to hang up a stamp without a cam stick, if the fingers are not more than 1/8 in. longer than necessary to hold the tappet above the cam.

Jan 12, 1914

By J. C. F. Randolph

This mill being now in successful work, it seems proper to record some professional memoranda concerning it. It is intended to handle an unusual ore, in a locality difficult of access, and its arrangement and method of procedure present some novel features of interest. It was prepared for the San Miguel property at Batopilas, State of Chihuahua, Mexico, owned by the Consolidated Batopilas Silver Mining Company of New York, at present under the management of ex-Governor Alexander R. Shepherd. This property contains a large series of more or less parallel veins, worked through a deep cross-cut tunnel 1300 feet in length. The vein rock of these veins is calcapar in diorite. While, near the stirface, ruby silver, black

Jan 1, 1882

By John C. F. Randolph

THIS mill being now in successful work, it seems proper to record some professional memoranda concerning it. It is intended to handle an unusual ore, in a locality difficult of access, and its arrangement and method of procedure present some novel features of interest. It was prepared for the San Miguel property at Batopilas, State of Chihuahua, Mexico, owned by the Consolidated Batopilas Silver Mining Company of New York, at present under the management of ex-Governor Alexander R. Shepherd. This property contains a large series of more or less parallel veins, worked through a deep cross-cut tunnel 1300 feet in length. The vein rock of these veins is calespar in diorite. While, near the surface, ruby silver, black

Jan 1, 1882

By John P. Goheen

Considerable work has been done in developing a pyrometer to measure the temperature of molten brasses, bronzes, and aluminum in the crucible. On account of the high melting points and the amount of zinc and sulfurous fumes given off from molten brasses, the conditions are somewhat severe for a thermocouple of standard design; but satisfactory results are obtained with a portable pyrometer, 3 ft. (0.9 m.) of connecting lead wire, and a special 5-ft. nickel-nickel chromium thermocouple, composed of rods 1/4in. (6.35 mm.) in diameter. The lower 12 or 24 in., as desired, may be made detachable so that new tips may be connected at little trouble or expense. The portable instrument need not be of the extreme high-resistance type, as the movable parts of the galvanometer of a lower resistance instrument may be better constxucted to withstand the continuous handling such an instrument receives. Platinum-platinum rhodium thermocouples, protected with porcelain and graphite tubes, have been used, but the lag in registering the temperature is too great. It has been found that the range of temperature for various brasses is as follows: Red brasses...............2200-2250" F. (1205-1234" C.) Yellow brasses............2250-2400" F. (1234-1318' C.) Bronzes..................2300-2550" F. (1260-1400" C.) A recent test with a portable pyrometer having a range of 2600" F. with a bare 1/4 in. heavy exposed couple 5 it. long and a handle attached at the upper end showed that the temperatures of molten aluminum under varying conditions in an oil-fired crucible furnace and one of the Simplex type were as follows: CRUCIBLE, OIL-FIRED FURNACE SIMPLEX FURNACE Temperature of metal in furnace....... 1540" F. (837" C.) 1530" F. (834" C.) Temperature in ladle after skimming at furnace......................... 1480" F. (805" C.) 1440" F. (784" C.) Temperature in ladle after skimming at floor near mold................... 1440" F. (784" C.) 1430' F. (778" C.)

Jan 1, 1923

By John P. Goheen

Considerable work has been done in developing a pyrometer to measure the temperature of molten brasses, bronzes, and aluminum in the crucible. On account of the high melting points and the amount of zinc and sulfurous fumes given off from molten brasses, the conditions are somewhat severe for a thermocouple of standard design; but satisfactory results are obtained with a portable pyrometer, 3 ft. (0.9 m.) of connecting lead wire, and a special 5-ft. nickel-nickel chromium thermocouple, composed of rods 1/4in. (6.35 mm.) in diameter. The lower 12 or 24 in., as desired, may be made detachable so that new tips may be connected at little trouble or expense. The portable instrument need not be of the extreme high-resistance type, as the movable parts of the galvanometer of a lower resistance instrument may be better constxucted to withstand the continuous handling such an instrument receives. Platinum-platinum rhodium thermocouples, protected with porcelain and graphite tubes, have been used, but the lag in registering the temperature is too great. It has been found that the range of temperature for various brasses is as follows: Red brasses...............2200-2250" F. (1205-1234" C.) Yellow brasses............2250-2400" F. (1234-1318' C.) Bronzes..................2300-2550" F. (1260-1400" C.) A recent test with a portable pyrometer having a range of 2600" F. with a bare 1/4 in. heavy exposed couple 5 it. long and a handle attached at the upper end showed that the temperatures of molten aluminum under varying conditions in an oil-fired crucible furnace and one of the Simplex type were as follows: CRUCIBLE, OIL-FIRED FURNACE SIMPLEX FURNACE Temperature of metal in furnace....... 1540" F. (837" C.) 1530" F. (834" C.) Temperature in ladle after skimming at furnace......................... 1480" F. (805" C.) 1440" F. (784" C.) Temperature in ladle after skimming at floor near mold................... 1440" F. (784" C.) 1430' F. (778" C.)

Jan 1, 1923

C. W. GOODALE, * Butte, Mont.-In regard to the employment manager, the North Butte Mining Co. has undertaken that line of work and the rest of the companies are watching the experiment. If it is proved to be the proper thing, the system will be introduced into other mines. We have to combat the opposition to the use of the "rustling card. It is nothing more nor less than asking the nationality, where the plan formerly worked, and whether he is married or single. ROBERT RHEA GOODRICH, Anaconda, Mont. (written discussion?).¬Since the efficiency of the different phases of personnel work employed by industrial concerns, which are bringing about greater efficiency and lessening the labor turnover, the latter being intimately connected with "contentment of mind," depends on the individual workman, it is highly desirable, as far as industry is concerned, to keep the workman's mind and body in trim in order to lessen accidents and produce a higher grade of work. Prevention being better than cure, health supervision of the workmen during employment should be maintained by the employers in order that mental alertness and physical well-being may be obtained. I have long believed, from observation in many plants, that when any problem is dependent on the individual workman, what he believes and what he does is vitally dependent on his health. I will follow with much interest what is to be clone in the future in relation to the subject of health supervision during employment (as well as medical examinations at the time of employment), and I hope this idea will be generally instituted in personnel work. A workman with good health and a contented mind should be an ideal component of a progressive industrial concern. The contentment of the workman is fostered by a number of admirable phases of welfare work which are being still further developed. The mental and physical well-being of labor should be the issue in Labor vs. Capital in the new period of the industrial promotion of the United States into which we are now entering.

Jan 4, 1919

By Frederic E. Carter

THE history of all the civilizations of the Eastern Hemisphere is underlaid and interwoven with the story of gold. Great nations rose, welded by the hand of the conqueror, flourished gloriously because of the wealth of gold inevitably attracted to them, only to fall, either through the sapping of their original virility by the softer living their material prosperity made possible, or by wars made upon them by enemies who craved possession of what was theirs. Imposing fleets sailed the seas, seeking gold or tangible wealth that might be converted into gold. Men suffered untold tortures in its quest. It sent Columbus out into unknown oceans, caused the migration of hordes of people from our Atlantic to our Pacific seaboard in '49 and accelerated the final subjection of our last frontier, probably by as much as a century. The mystic may see both something sinister and something beneficent in this metal that has played such a tremendous part in the shaping of the destinies of men. It has showered blessings and taken them away. It "hath deposed the mighty from their seats and hath exalted men of low degree" and, sardonically, reversed the order yet again. Its peculiar color, its incorruptibility, and its rarity all have contributed to excite the imagination of all races of men. In the Eastern Hemisphere and now in the entire modern world, the predominant emotion excited by gold is avarice. But in the social and economic organization of the civilizations native to the western half of the world, gold has a far different history. Before the advent of the white man, these sun-worshipping peoples saw in the permanently

Jan 1, 1953

By E. D. Levine

A study was made to delineate the dislocation mechanistns controlling prismatic and basal slip at low temperatu.ves in titanium containing approximately 100 ppm interstitial impurities. Mechanical tests were performed on single crystals prepared from electron-beam zone-refined crystal bar by a thermal cycling technique. Measurements were made of critical shear stress and activation volume as functions of temperature. The study revealed that, for prismatic slip, two overlapping thermally activated processes aye rate-controlling below 300°K. From absolute zero to 220°K, reasonable agreement is obtained between experiment and the mechanism which involves overcoming 01. the Peierl's stress by the formation of double kinks in dislocation lines lying in close-packed directions. Between 220°and 300°K prismatic slip is controlled by a difierent thermally activated process which is characterized by a stronger temperature dependence of critical shear stress. Above 300OK, prismatic slip is controlled by an athermal process. Basal slip is controlled by a thermally activated process between 195' and 400°K. An approximate analysis suggests that it is the Peierl's mechanism that is rate-controlling in this range. Below 195°K, the occurrence of mechanical twinning obscures the features of basal slip. Above '400 X, basal slip is controlled by an athermal process. TITANIUM, an hcp metal with a less-than-ideal axial ratio of 1.587, deforms primarily by {1010}( 1210) slip at low temperatures.'-3 The critical shear stress is strongly affected by the presence of interstitial impurities. For example, churchman3 reported that a decrease in the combined nitrogen plus oxygen content from 0.1 to 0.01 pct decreased the critical shear stress for prismatic slip from 9.19 to 1.4 kg per sq mm at room temperature. Basal slip, however, is less strongly affected by interstitials; Churchman's data for {0001}( 1210) slip show a smaller decrease in critical shear stress from 10.90 to 6.3 kg per sq mm at room temperature, for the same decrease in interstitial content. In the present study, an attempt has been made to delineate the dislocation mechanisms controlling prismatic and basal slip in titanium. In view of the strong effects that impurities may have on at least some of these mechanisms, experiments were performed on material of reasonably high purity, so that comparisons could be made with investigations on material of both lower and higher impurity contents. EXPERIMENTAL PROCEDURE Single crystals were prepared from 1/4-in.-diam electron-beam zone-refined crystal bar, furnished by Materials Research Corp. The analysis of the zone-refined material is given in Table I, indicating that the interstitial content is of the same order as the purer of the two materials investigated by Churchman. The Vickers diamond pyramid hardness number of this material was 85.6. This value agrees quite well with the correlation between hardness and interstitial content proposed by Ogden and Jaffee.4 On the basis of hardness, the material investigated in this study is, therefore, intermediate in purity between that studied by Churchman (Vpn = 97) and that studied by Spangler and Herman (Vpn = 62.4).5 Single crystals were grown by thermal cycling through the a-ß transformation. Two-in.-long by 1/2-in.-diam bars were heat-treated in vacuum for 4 hr at 1160°C. The temperature of the furnace was then lowered to 865°C, and the specimens were maintained at this temperature for 7 days. This procedure was repeated several times, resulting in the growth of individual crystals up to 14 in. in length. Specimens for testing in direct shear along either {l010}(1210) or {0001}(1210) were obtained by electrical-discharge machining. The specimens were in the form of cylinders 1/4 in. in diam by approximately 1/2 in. in length, with a reduced section 1/8 in. in diam and a in. in length. All specimens were electropol-ished subsequent to electrical-discharge machining. The ends of the test specimens were cemented in stainless-steel collars. Shear tests were conducted in an Instron Tensile Tester at various temperatures from 4.2° to 508°K. Measurements were made of critical shear stress and activation volume. The latter measurements were performed by measuring the change in flow stress upon cycling the strain rate between ?1 = 2.62 x 10-3 per sec and ?2 = 2.62 x 10-4 per sec. Activation volume, I)*, is defined as u* =ßkT [11

Jan 1, 1967

By M. A. Dayananda

Based on the Kirkendall frame of reference, a method is proposed for the determination of atomic mobilities of all the diffusing species in a multicorn-ponent system with a single diffusion couple. The method is based on an atomic mobility model developed on the concept of negligible interactions among the intrinsic fluxes. It is shown in the model that mobilities can be obtained directly from the cumulative intrinsic fluxes past the Kirkendall interface. The proposed method replaces the need for a prior determination of interdiffusion coefficients far the calculation of mobilities. Relations between intrinsic diffusion coefficients and mobilities are derived and the mobility calculations are illustrated with diffusion data in Cu-Zn-Mn alloys at 850°C. ThE concept of "intrinsic flux" with respect to a fixed lattice was introduced "i Darken1 to explain toa Kirkendall effect2 demonstrated by the motion of inert markers during isothermal diffusion in single-phase binary solid solutions. Based on this concept, intrinsic diffusion studies have been made in various binary metallic systems3,4 employing such a lattice frame of reference, commonly referred to as the Kirkendall interface. Similar approaches, both theoretical and experimental, have been presented5"10 to study intrinsic diffusion in multicomponent systems. Based on the direct integration of Fick's law extended to multicomponent diffusion, Philibert and Guy8 proposed a method for the determination of intrinsic diffusion coefficients. For an n-component system, this procedure requires an experimental study with (n — 1) diffusion couples, all having their Kirkendall interfaces at the same compositio;, where n(n — 1) intrinsic diffusion coefficients are defined. This technique has been employed for ternary diffusion studies by Dayananda and Grace" and Guy and Leroy.11 A different approach is recommended by Ziebold and Cooper,12 who have derived relations between interdiffusion coefficients and atomic mobilities employing fluxes referred to the local center of volume. Their analysis is based on the simplifying assumption of negligible interactions among intrinsic fluxes. This assumption has been considered satisfactory for dilute solutions.5"7 The use of this analysis for the calculation of mobilities requires an initial determination of interdiffusion coefficients with a set of diffusion couples having intersecting diffusion paths. It is the purpose of this paper to propose a method that would permit a direct determination of mobilities of all components of a multicomponent system from a single diffusion couple. This method is based on a mo- bility model developed with diffusion fluxes referred directly to the Kirkendall interface, generally identified by inert markers. gen erall, like that of Ziebold and Cooper,12 employs the simplifying assumption that the flux of each component relative to a fixed lattice is caused only by the driving force of its own chemical potential gradient. THE KIRKENDALL INTERFACE Inert markers are employed in diffusion couples to locate experimentally the position of the Kirkendall interface. They are initially placed at the weld interface for "sandwich" couples, or at the original vapor-solid interface for vapor-solid couples. Studies of marker motion in binary systems3'4 with both types of couples indicate that markers remain in a plane of constant composition and move with this plane para-bolically with time. Parabolic marker movements were also observed in ternary Cu-Zn-Mn couples by Dayananda and Grace.10 It is reasonable to expect a similar marker behavior even for diffusion couples with a higher number of components.

Jan 1, 1969

By H. M. Boylston

Metallic manganese was first produced in 1773, by Sven Rinmann, a Swedish mineralogist. In 1799, William Reynolds, of Ketley, England, obtained a patent on the use of manganese dioxide in the manufacture of steel, and in 1808 an English patent was granted to John Wilkinson covering the use of manganese ore, or manganiferous ore, as an addition to iron ore in the blast furnace for the production of a superior grade of pig iron. Karsten showed in 1816 that manganese increased the hardness of iron without decreasing its malleability or toughness, while it caused pig iron to be more white in fracture and more fusible. The first practical application of manganese to steel-making, however, is attributed to Josiah Heath who discovered in 1839 (less than 90 years ago) that manganese conferred upon steel the properties of being more easily worked and welded under the hammer. When Bessemer invented the pneumatic process of steel-making which now bears his name he was at first successful because, as it afterward developed, he was using a Swedish pig iron high in manganese. When his supply of this material ran out, he used a low-manganese pig from English sources and failed signally to produce a steel which could be rolled, while his Swedish licensees were continuing their successful application of his method. And it was not until Robert Mushet, in 1856, suggested the addition of manganese in the form of spiegeleisen to the molten product of the converter that success again came to Bessemer. In 1866, William Siemens patented the use of ferromanganese as an addition to molten steel to counteract the bad effects of sulfur. It was in 1888 that Robert Hadfield published at some length his account of the effect of manganese as an alloying element in steel and described the unique properties of the now famous Hadfield manganese steel containing about 12 to 14 per cent. manganese and 1.25 per cent. carbon. Function or Manganese in Steel-making Bessemer's failure at one period of his experimental work to make steel which could be forged successfully was due to the fact that the

Jan 1, 1927

By R. W. Smith

Many industries such as the cement industry handle large quantities of limestone and clay slurries. However, at present very little is known about the flow properties, such as friction loss due to flow of slurries in pipelines. This lack of knowledge has made it often very difficult to calculate the total dynamic head of a proposed slurry handling system, and therefore has often made the selection of correct size slurry handling equipment difficult. Because of lack of knowledge about slurry flow a study of slurry flow theory has been made at the Portland Cement Association's Research and Development Laboratory with the idea of developing a method whereby friction losses due to slurry flow may be predicted for any size pipeline. The flow equations developed have been checked by pilot plant size equipment. DERIVATION OF FLOW EQUATIONS It has been known for some time that limestone and clay slurries handled in cement plants do not flow in the same manner as a Newtonian fluid such as water. When a Newtonian fluid flows the shear stress at any flow velocity is proportional to the rate of shear. This phenomenon can be illustrated by a line (Figure 1). The viscosity of the fluid is the slope of the curve. Thus, the flow properties of the material may be characterized by a single materials constant: viscosity. When a non-Newtonian fluid with the type of characteristics exhibited by limestone and clay slurr-ries flow, a similar curve can be constructed (Figure 2). This graph is a shear diagram of a Bingham plastic non-Newtonian fluid. It should be noted that with the Bingham(1) plastic type of flow viscosity, the slope of the curve, is still an important materials constant. In addition, however, there is another materials constant, namely the yield stress of the material. One way to visualize this constant is to consider it as the amount of energy that must be put into a Bingham plastic material to start it flowing.

Jan 1, 1961

By K. Takahashi, I. Iwasaki

it is well known1 that racemic mixtures of optical isomers can be separated by passing their solutions through a column packed with r- or 1-quartz powder so that one of the isomers becomes adsorbed selectively on the asymmetric quartz surfaces. Although the natural occurrence of r- and 1-quartz is more or less equally distributed, some localities show enough deviations toward a higher proportion of l-quartz2 to suggest that optical isomerism might influence quartz flotation. Beta-amines have an asymmetric carbon atom, and therefore optical activity may be expected. Beta-amines are reported to behave quite differently from alpha-amines in the flotation upgrading of certain oxidized iron ores.3 It is of interest, for both practical and theoretical reasons, to determine whether or not optical isomerism plays a role in the amine flotation of quartz. In this article the results of Hallimond tube flotation tests and of adsorption measurements using d-beta-phenylisopropylamine on both r- and 1-quartz are compared. D-beta-phenylisopropylamine was chosen for the tests because it is commercially available in optical isomers. MATERIALS AND METHODS Brazilian quartz crystals were hand-sorted according to the difference in trigonal trapezohedral faces, and each crystal was further checked by the Airy's spiral.4 The respective crystals were then crushed, and the -150 + 200-mesh fractions were screened out for the Hallimond tube tests. The samples were cleaned by brief leaching with warm, dilute hydrochloric acid, and then by repeated rinsing with distilled water. In preparation for the adsorption measurements, they were then dry-ground in a pebble mill for several hours, washed a few times with distilled water, and finally dried in a vacuum desiccator. By means of the Krypton gas adsorption method, the specific surfaces of r- and 1-quartz samples were determined to be 27,700 and 19,800 sq cm per gm respectively, the difference being due mainly to the decantation procedure rather than to the inherent difference in their grindability. D-beta-phenylisopropylamine was the only collector used in the study. It was solubilized by neutralizing with 110% of the stoichiometric requirement of 0.1 N hydrochloric acid. The specific rotation of the d-beta-phenylisopropylamine was determined with a polari-meter using sodium D line to be, Although the d-beta-phenylis~prop~lamine showed absorption maxima in the wave length region of 250 to 270 millimicrons, due presumably to the phenyl group, these peaks were too sensitive to be used for colorimetric determination of the residual concentration in the adsorption measurements. The amine-picrate method, used in the colorimetric analysis of dodecylammonium chloride,' was found to work satisfactorily for the d-beta-phenylisopropylamine. The adsorption densities were thus determined after equilibrating 40 gm of the ground quartz sample with 300 ml of solution by tumbling in separate glass-stoppered Erlenmeyer flasks for one hour. EXPERIMENTAL RESULTS Fig. 1 presents the adsorption densities of d-beta-phenylisopropylamine on the r- and 1-quarts in the pH range of 6 to 7.5. In agreement with data reported in the literature, the adsorption density of d-beta-phenylisopropylamine was slightly higher on the r-quartz than on the 1-quartz, although the difference was not as pronounced as one might expect from the capacity of r-quartz and 1-quartz to separate racemic

Jan 1, 1969