Search Documents

By Edward Keller

GOLD MOVEMENT ON SURFACE OF AURIFEROUS COPPER WHEN LATTER IS SUBJECTED TO OXIDATION SOME years ago the writer's attention was called to the fact that rolling-mill scales from auriferous copper do not have the gold content proportional to the gold contained in the copper from which they are derived. I So, later, he made a few simple experiments, which are described herewith. In: order to test the gold movement on the changing surface of a copper plate under the influence of oxidation, plates 6 in. by 8 in. by I in. (15.2 cm. by 20.3 cm. by 2.5 cm.) of converter copper, refined, of 99.29 per cent. purity, and leaded copper with a content of 95.65 per cent. copper, were obtained. Ten cuts were made through the thickness of the plates along the longitudinal center and the silver and gold content ascertained in each of the 10 samples in both plates, as shown in the accompanying illustration. The assay results, recorded in Tables 1 and 2, show that the gold distribution is relatively uniform in both plates, while silver has greater variations, especially in the leaded plate. The plates subjected to oxidation were placed in a red-hot muffle for about 2 hr., two small scorifiers being used as supports. Arranged alongside each other, they nearly filled the width of the muffle, and so were practically under equal conditions of heat and draft. The accurate observance of the time was not possible, however, because of other work, but the time of the exposure of each plate in a pair was identical. At the end of each period, each plate was plunged into water and completely freed of scale, which was carefully collected, dried, weighed, and analyzed. Samples of the plates had also been taken of the molten metal and duly analyzed. Table 3 contains the analytical data for the two plates and their several sheets, or layers, of oxide scales. These figures show that in the oxidations of the converter copper the silver is fairly uniform, while

Jan 1, 1919

By B. H. Caudle, A. B. Dyes

In a recent publication' it was shown that wells with a free surface in a homogeneous gravity-drainage reservoir have a hyperbolic decline with index n '. This paper reports efforts to extend this theory to practical field cases. As a first step in making the extension, a large number of lease production curves from gravity-drainage fields in the stripper stage were fitted with the general hyperbolic decline equation, q/q, = 1/(1 + y) y and n in each case being determined by statistical methods. It was found that this equation is reliable for decline curve extrapolation for periods up to at least 25 years. The resrilts obtained were disturbing in the sense that values for the index, n, were often smaller than one, which fact leads to the prediction that a well would produce all infinite amount of oil in infinite time. A theoretical investigation based on the results of the previous paper provides a suitable explanation for these low values of n. It suggests that these are obtained if production occurs from two or more layers of diflerent permeabilitv and thicktress or two lnyers having different skin effects. It is predicted that as the more permeable layers are exhausted, the index of decline, n, will rise from a value smaller than 2, to n = 2. A practical method is given for fitting the general hyperbolic decline Eq. 6 to production decline data. When this method is used, the index of decline observed in gravity-drainage reservoirs in the stripper stage when wing only data over early years 01 decline usually agrees quite closely with that determined using data over 25 years or more. This indicates that the hyperbolic decline equation is reliable for predicting behavior of such reservoirs. A method is also suggested for taking into account any changes in the value of the index INTRODUCTION As a result of both experimental work with models and theoretical deductions, it was recently concluded' that wells having a free surface in a homogeneous reservoir producing by pure gravity drainage should have a hyperbolic decline with n = 2. The present report details efforts to extend this work on ideal homogeneous reservoirs to actual field cases. It should be remembered that both the previous work and the present extension are based on the assumption that the reservoir is at very low pressure, and hence, nearly all the potential available for driving fluid to the well is the gravity head. Attempts to apply conclusions of this study to reservoirs which have considerable pressures supplementing the gravity drive may lead to difficulty. WELLS WITH NO FREE SURFACE In a dipping gravity-drainage reservoir such as that shown in Fig. 1, some of the down-dip wells have no free surface. The previous study' showed that the up-dip wells, which have a free surface, should follow Eq. 1. The following approximate analysis, of a type which was justified experimentally for up-dip wells in the work just mentioned, leads to results for the down-dip wells.

By Walter Kauzmann

EyRing'S general theory of shear rates as a function of the properties of molecular units of flow is outlined and applied to the creep of metals. This theory regards the unit molecular processes involved in the flow of matter as typical chemical reactions requiring an energy of activation in order to proceed. The externally applied stresses are assumed to influence the rate of flow solely by lowering the activation energy for flow in one direction and raising that for flow in the other, owing to the work that is done by or against the external forces in going from the normal to the activated state. The rates of flow in the two directions are then no longer equal arid there is a net, macroscopically observable flow in one direction. This is understood to be the physical basis for the well-known exponential dependence of the creep rate on the stress. The amount by which the activation energy is raised and lowered by a given external stress is directly related to the molecular dimensions of the unit of flow, so that some insight into these call be found from the behavior of the strain rate with changing stress. When Eyring's equation is applied to the flow of ordinary liquids, such as water or benzene, it has been found from the values of the constants required to fit the observed data that the unit molecular process here involves the passage of single molecules by one another. In metallic creep, on the other hand, the unit molecular process is shown probably to involve the shear of rather large blocks of material (100 to 1000 or more atoms on a side). This agrees with present ideas of crystal flow by means of dislocations such as have been presented by Taylor, Oroaan, and Polanyi, as opposed to flow by a mechanism related to that taking place in atomic diffusion. The dimensions of the dislocations are found to depend markedly on the temperature. The questions of why some metals are so much softer than others, the effects of impurities on hardness, the softness of single crystals, and the role of self-diffusion in creep are considered in the light of the theory and it is shown how answers to these questions (and others similar) might be obtained by use of the theory.

Jan 1, 1941

By Walter Kauzmann

EyRing'S general theory of shear rates as a function of the properties of molecular units of flow is outlined and applied to the creep of metals. This theory regards the unit molecular processes involved in the flow of matter as typical chemical reactions requiring an energy of activation in order to proceed. The externally applied stresses are assumed to influence the rate of flow solely by lowering the activation energy for flow in one direction and raising that for flow in the other, owing to the work that is done by or against the external forces in going from the normal to the activated state. The rates of flow in the two directions are then no longer equal arid there is a net, macroscopically observable flow in one direction. This is understood to be the physical basis for the well-known exponential dependence of the creep rate on the stress. The amount by which the activation energy is raised and lowered by a given external stress is directly related to the molecular dimensions of the unit of flow, so that some insight into these call be found from the behavior of the strain rate with changing stress. When Eyring's equation is applied to the flow of ordinary liquids, such as water or benzene, it has been found from the values of the constants required to fit the observed data that the unit molecular process here involves the passage of single molecules by one another. In metallic creep, on the other hand, the unit molecular process is shown probably to involve the shear of rather large blocks of material (100 to 1000 or more atoms on a side). This agrees with present ideas of crystal flow by means of dislocations such as have been presented by Taylor, Oroaan, and Polanyi, as opposed to flow by a mechanism related to that taking place in atomic diffusion. The dimensions of the dislocations are found to depend markedly on the temperature. The questions of why some metals are so much softer than others, the effects of impurities on hardness, the softness of single crystals, and the role of self-diffusion in creep are considered in the light of the theory and it is shown how answers to these questions (and others similar) might be obtained by use of the theory.

Jan 1, 1941

By F. D. Rosi

The plastic properties of extended silver and copper crystals of varying purity were studied as a function of crystal orientation in the early stages of flow. Variations in the gross shape of the shear stress-shear diagram and in the properties of critical Variationsshear stress and shear-hardening coefficient were correlated with changes in slip-band developments. The phenomenon of work hardening is discussed in terms of the existing dislocation theory. IT appears certain from the early studies on the deformation characteristics in metal crystals1-3 that plastic flow takes place in a preferred crystallo-graphic slip system which is determined by the geometry of the crystal (law of maximum shear stress), and that the value of shear stress for this system is independent of crystal orientation (law of critical shear stress). Experimentally, it has been demonstrated further that the law of critical shear stress can be extended to include extensive plastic flow.&apos; Thus, the shear-hardening coefficient, which is defined as the slope of the shear stress-shear curve, also is considered to be independent of orientation. It is noteworthy that deviations from this empirical shear-hardening law have been reported in cubic crystals whose initial orientation favors slip on more than two systems.&apos; Moreover, this law appears to have been derived from stress-strain data relating to relatively high values of shear strain (0.5 to 4), where widespread slip and complex distortions can be expected, regardless of crystal orientation. Since existing data indicate that the strain inhomogeneity in a crystal is manifested particularly in the early stages of flow, it would appear that a more exacting test as to the fundamental nature of the shear-hardening law would be to investigate systematically the shape of the stress-strain curve as a function of crystal orientation in the earlier stages of deformation. With regard to the general form of the shear stress-shear curve for cubic crystals, early studies show a parabolic hardening law, where the shear 1 stress is proportional to the square root of the shear-strain. Since this law was predicted theoretically by Taylor" in his original dislocation model for hard- ening, it has been accepted widely as a fundamental flow characteristic of cubic metals. However, it was recently pointed out by Masing6 hat the parabolic law is not the elementary form of hardening in cubic crystals, but instead is a consequence of complexities in the flow process (e. g., deformation bands and unpredicted secondary slip). Thus, in the very early stages of deformation (< 2 pct extension) where the occurrence of such complexities is unlikely, a different strain-hardening behavior might be anticipated. This view is supported by the recent work of Rosi and Mathewson7 on high purity aluminum where a linear law was obtained for extensions up to 2 pct. A linear hardening over a wider range of deformation also was reported by Rohm and Kochendorfer8 ho deformed aluminum crystals under conditions approximating pure shear. Even more pertinent is the recent evidence of Masing and Raffelsieper9 on high purity aluminum crystals. It was found that for crystals having initial orientations near a <l00> or <1ll> axis, a high hardening was obtained, whereas crystals with a <110> orientation exhibited a low and linear hardening curve followed by a region of more rapid hardening. Since much still remains obscure concerning the details of strain hardening as well as slip-band formation in face-centered-cubic crystals in the early stages of deformation, the present study was undertaken to evaluate the effect of crystal orientation on these two important manifestations of glide. It is important to note here that at the time of this study, Lucke and Lange11 presented information on the orientation-dependence of the shape of the strain-hardening curve in aluminum of various purities. Their work, which essentially represents an extension of that of Masing and Raffelsieper, in many respects is parallel to that of the present study. Experimental Procedure Production of Single Crystals: Single crystals of silver and copper of varying purity were used in

Jan 1, 1955

By C. Edwin Nighman

THE following is a description of the methods used in rescuing men and extinguishing the underground fire at the Pennsylvania mine, Butte, Mont. This fire, which cost the lives of 21 men, began about 9 p.m., Feb. 14, 1916, at or near a ventilating fan on the 1,200 air-shaft station. This shaft at that time was downcast, while the main hoisting shaft was upcast. Owing to the proximity of the fire to the air shaft, the air in the latter soon became heated, and as the fan on the level was not running¬the power having been cut off shortly after the outbreak&apos; of the fire-the aim&apos; shaft became upcast to the 300 level. At this point a blanket of cold air from the surface caused the smoke and gases to he drawn in on that level and carried down again through the workings to the 1,200. A short time after the discovery of the fire, water was turned down the air shaft through a series of pipes around the collar of the shaft, which caused the smoke to recede, below the 300, so that within 2 hr. it was possible to search that level for the missing men. From the above it will be apparent why the air shaft was upcast instead of downcast as under normal conditions, and why men were suffocated at considerable distances from the seat of the fire. The smoke and gases that came up the main hoisting shaft did not diffuse through the workings to any extent. There are doors on all levels in the connections to the main hoisting and air shafts, but-in the confusion and running around many of these doors were left open, and this undoubtedly caused the smoke and gases to spread more rapidly than they would otherwise have done. It was necessary for most of the men on the various levels to pass close to the air shaft in going to the hoisting shaft, and when they encountered the smoke and gases in that vicinity a number turned hack and climbed down with the direction of the air currents and were then suffocated, while all those who passed through the relatively short pall of smoke to the main shaft were saved.

Jan 2, 1917

By R. V. Smith, M. H. Cullender

Rigorous equations for calculating subsurface pres.tures in flowing and static gas wells, and pressures along horizontal pipelines are presented in this paper. These general equations, based on the mechanical encrgy balance, contain no assumptions regarding temperature and can be used with either straight-line or curved temperature gradients. The friction factors recommended in this report are based on an absolute roughness of 0.0006 in. Flow is always considered to he turbulent. Although these general flow equations are solved by numerical means, the methods are as convenient as many of those used today to calculate pressures in gas wells and pipelines. These numerical methods are illustrated for flowing and static columns of gas in wells and for flow in pipelines. The authors believe that the use of these methods will result in more accurately calculated pressures in gas wells and pipelines and that [he methods are more flexible than any in use at the present time. Also, the methods are easily adaptable to automatic computers. INTRODUCTION The problem of calculating subsurface pressures in gas wells and along flowing pipelines has been studied by many investigators with the results that two widely-used methods have been presented in technical literature. One approximates conditions in a gas well or pipeline by assuming that temperature and compressi- bility are constants tor the entire gas column. The other method assumes that temperature is constant at some average value but permits compressibility to vary with pressure at the constant temperature. While these approximations may be justified for relatively shallow and low-pressure wells, they become more and more unrealistic as the calculations are applied to the deeper high-pressure wells. In wells or pipelines where there is an appreciable change in temperature between the inlet and outlet ends of the flow string, it is equally as important to consider the change in compressibility with temperature as it is to consider the change with pressure. Consequently, the methods presented in this paper were developed to provide a workable procedure for calculating pressures in gas wells and pipelines which makes no assumptions regarding either temperature or compressibility. The friction factors recommended for use with the equations were the result of study of published literature and extensive experimental work with gas wells. The F,. values in Appendix IV which contain the friction factor are equivalent to an absolute roughness of 0.0006 in. as calculated by the Nikuradse equation. The absolute roughness of 0.0006 in. was previously published by Cullender and Binckley2 for gas wells; it is in agreement with 0.00065 in. of Smith, Dewees, and Williams1 for gas wells and 0.00065 in. of Baker and Swerdloff4 for pipelines; it is in reasonable agreement with 0.0007 in. reported by the Bureau of Mines and the American Gas Assn.5 for large transmission lines. However, any type of friction factors may be used in the equations by a change in the F, values in Appendix [V].

Jan 1, 1957

By L. Michael Kaas

The mineral industries are striving to expand their use of the computer&apos;s ability to process exploration, geologic, and mining data. Digital plotting programs and devices are continuing to gain wider use for lowering the cost and the time required to produce many types of maps and cross-sections commonly used by mining companies. Mineral engineers and geologists will soon be using a new tool, computer graphics, to greatly facilitate the use of computers to solve a large number of industry problems. By means of cathode-ray-tube (CRT) displays, an engineer can search large files of geologic data; display elevation contours, geologic structures, and ore grades; construct geologic and mining cross-sections; and compute tonnages for mining plans or ore reserve estimates. Examples of both digital plotting and cathode-ray-tube problem solving approaches are discussed in this paper.

Jan 1, 1969

By M. J. Ginsberg, N. A. Gokcen

THE preliminary study of electrochemical desul-furization performed by Ohtani and Gokcen1 left a number of points concerning the process to be investigated. Two of these were i) the determination of the effect of greater current and voltage on the desulfurizing Flower of acid slags (% CaO/% SiO2- 1) and ii) the possibility of the loss of silica in slag by the reactions 2C (in metal) + SiO2 (slag) = Si (in metal) + 2CO(g) and C + SiO2 (in slag) = SiO(g) + cO(g) proceeding to a point at which the composition of the slag was sufficiently altered toward the basic side so a1.s to noticeably affect the rate of de-sulfurization. The apparatus and the procedure used in the present investigation were the same as those used by Ohtani and Gokcen, except the control circuit was connected to 120 v dc instead of 24 v dc and thereby allowed greater freedom in choosing the values of both current and voltage. The graphite crucible containing the melt and serving as the cathode was 3-in. high, and was of 1 1/2-in. ID with a graphite bar of 3/8-in. diam and 8-in. length threaded into the bottom for electrical connection. This was placed into a magnesja outer crucible with a hole in the bottom and alumina insulation was packed between the two crucibles. A charge consisting of 180 g of

Jan 1, 1962

By T. N. Dixon, J. E. Briggs

A study was made of numerical techniques for solving the large sets of simultaneous equations that arise in the mathematical mode ling of oil reservoir behavior. It was found that noniterative techniques, such as the Alternating Direction Implicit (ADI) method, as well as some other finite difference approximations, produce oscillatory or unsmooth results for large time steps. Estimates of time step sizes sufficient to avoid such behavior are given. A comparison was made of the Point Successive Over-Relaxation (PSOR), Two-Line Cyclic Chebyshev Semi-Iterative SOR (2LCC), and iterative ADI methods, with respect to speed of solution of a test problem. It was found that, when applicable, iterative ADI is fastest for problems involving many points, while 2LCC is preferable for smaller problems. INTRODUCTION With the advent of high speed, large memory, digital computers, there has been an increasing emphasis on the development of improved methods for simulating and predicting reservoir performance. Two-dimensional, three-phase reservoir models with various combinations of PVT effects, as well as gravity and capillary forces, are common throughout the industry. Such models are also available through consulting firms, to anyone desiring to use them. Three-dimensional models will probably be practical in only a few years. We conducted a study of some of the numerical methods used for solving the large sets of simultaneous equations that arise in such models. A typical set of equations for a reservoir model is shown below:

Jan 1, 1969

By Gen-Hua Shi, William Boyle, Richard E. Goodman

This keynote paper calls attention to two critically important issues relating to selecting supports for excavations in hard rock. The first is the proportion of the ultimate sliding volume that needs to be stabilized by the support system. Some excavations can be imagined to liberate very large rock volumes, whose weight can not be assigned to supports without severe economic penalty. Using the keyblock principle, it is argued that only the most critically oriented and finite blocks right on the periphery of the opening have to be supported; if these are retained by the support system, or by self resistance due to friction on the sliding faces, then the blocks behind will remain in place. As all concepts, this one has bounds and limits. Since the keyblock analysis for rock engineering is very new, these limits are not yet understood ... The second issue is the degree to which possibly stabilizing forces associated with the in-situ stress field ought to be accepted as support for potential keyblocks. It is shown that the initial stress can be effective in stabilizing rock wedges whose faces are nearly perpendicular to the excavation surface. It is too early to decide this issue but important to consider it.

Jan 1, 1982

By Yap Chu-Phay

IN 1923, when the writer began his studies in metallurgy, he came upon an article by Professor Honda on the, Equilibrium Diagram of the Iron-carbon System, 1 which made a profound impression on him. What interested him most was this sentence: "In the recent diagram of the iron-carbon system, the solidus is usually shown as a curve bending considerably downward. But it can be shown by thermodynamics that if the liquidus is straight or slightly curved, the same must also be true for the solidus. Hence, in my constitutional diagram, the lower portion of the solidus is slightly bent upward." Ever since then the writer has been interested in thermodynamics, especially chemical thermodynamics. The applications of thermo-dynamics to the metallic systems have been, in the writer&apos;s opinion, sadly neglected, although we continually use the phase rule in our study of equilibria in the liquid and solid states of metallic alloys. Many investigators, among whom may be mentioned Heycock and Neville, and s Honda and his coworkers, have applied the simple Raoult-van&apos;t Hoff law of depression of freezing point, mainly to determine the heat of fusion, but no attempt has been made to investigate the applicability of the thermo-dynamic laws of solution (as opposed to the laws of solution derived from other sources) to metallic systems" showing either limited or complete solid solutions. Perhaps the reason for this neglect is that until recently there have been so few reliable data on the solidus, which is much more difficult to determine than the liquidus. The writer has under way at the present time an investigation of a number of systems, the solidi of which have been more or less reliably determined. Recently, the writer has not only shown the valid applicability of the thermodynamic laws of solution as applied to the system antimony-bismuth but has also suggested a method of attacking problems involving complete and incomplete equilibria.2 In the present paper, the same method of approach is employed. For convenience, we shall divide this paper into two parts:

Jan 1, 1931

By J. J. Rutledge

On Sept. 4, 1914, Mine No. 1 of the Union Coal Co., Adamson, Oklahoma, suddenly caved, entombing thirteen miners whose bodies were never recovered. The seam of coal mined, the Lower Hartshorne, averaged 5 ft. in thickness and dipped at an angle varying from 22" to 30n. The strata overlying the coal seam were sandstones and shales. The mine was worked by the pillar-and-room method, the rooms being driven directly up the dip of the seam. All coal was blasted off the solid. Rooms were turned on short centers and room pillars were thin and irregular, as shown in Fig. 1. Fig. 2 is a cross-section of the form; showing the mine workings. Some cracks had been observed on the surface, it is said, at least a month before the squeeze occurred, but the collapse of the mine workings came very suddenly. As is usual when squeezes occur on such steep dips and the pillars fail, the crush progressed rapidly down the dip until it reached solid coal; there was a line of break, or draw, over in the solid coal. Several well-defined cracks appeared on the surface, after the mine had squeezed, but there was no appreciable subsidence of the surface, the weight seemed to be thrown entirely to the dip. About one year after the squeeze, and after the workings of the adjoining mine, NO. 4, had been retimbered and made safe, the writer inspected the tenth north (right) entry, or lift, off of No. 4 slope, which was below and fairly near the lowest caved portion of mine No. 1. The roof shale was composed of thin layers, which had been bent in somewhat the same manner as the leaves of a book having flexible covers are bent when the book is folded or rolled up in the hands. Though the mine workings are immediately beneath the streets and buildings of the mining town of Adamson, business was not disturbed by the squeeze, so far as any subsidence of the surface was concerned. No surface monuments were available and no elevations were taken, but the mine workings had been accurately surveyed and traversed, and the streets of the town overlying the mine workings had been carefully platted on the mine map, so that it was possible to locate accurately the cracks on the surface.

Jan 1, 1923

By J. J. Rutledge

On Sept. 4, 1914, Mine No. 1 of the Union Coal Co., Adamson, Oklahoma, suddenly caved, entombing thirteen miners whose bodies were never recovered. The seam of coal mined, the Lower Hartshorne, averaged 5 ft. in thickness and dipped at an angle varying from 22" to 30n. The strata overlying the coal seam were sandstones and shales. The mine was worked by the pillar-and-room method, the rooms being driven directly up the dip of the seam. All coal was blasted off the solid. Rooms were turned on short centers and room pillars were thin and irregular, as shown in Fig. 1. Fig. 2 is a cross-section of the form; showing the mine workings. Some cracks had been observed on the surface, it is said, at least a month before the squeeze occurred, but the collapse of the mine workings came very suddenly. As is usual when squeezes occur on such steep dips and the pillars fail, the crush progressed rapidly down the dip until it reached solid coal; there was a line of break, or draw, over in the solid coal. Several well-defined cracks appeared on the surface, after the mine had squeezed, but there was no appreciable subsidence of the surface, the weight seemed to be thrown entirely to the dip. About one year after the squeeze, and after the workings of the adjoining mine, NO. 4, had been retimbered and made safe, the writer inspected the tenth north (right) entry, or lift, off of No. 4 slope, which was below and fairly near the lowest caved portion of mine No. 1. The roof shale was composed of thin layers, which had been bent in somewhat the same manner as the leaves of a book having flexible covers are bent when the book is folded or rolled up in the hands. Though the mine workings are immediately beneath the streets and buildings of the mining town of Adamson, business was not disturbed by the squeeze, so far as any subsidence of the surface was concerned. No surface monuments were available and no elevations were taken, but the mine workings had been accurately surveyed and traversed, and the streets of the town overlying the mine workings had been carefully platted on the mine map, so that it was possible to locate accurately the cracks on the surface.

Jan 1, 1923

By William Clark

A bean placed at the bottom of tubing in flowing wells is not a new idea. In fact, a device which in effect was a bottom bean was patented prior to 1890 by John D. Rockefeller. Because of the limited use of the bottom bean, prior to 1922, when it was installed in a few wells in the Santa Fe Springs field, California, the knowledge of the results of its operation is very meager. Since then various oil operators have experimented with bottom beans, but most of the records of the results obtained by their use are unavailable. For the past year or two, more attention has been directed to this method of producing wells; the theory and best means of application have been studied, and accurate records maintained. In theory, the use of bottom beans in flowing or gas-lift wells should secure certain advantageous results. With the exception of flow friction of the tubing and flow lines, there is no back-pressure held on the rising column of fluid. Thus severe beaning is possible with no danger of killing the well by too heavy a fluid column, a condition that often exists when a surface bean is used. The whole energy of the gas expanding to atmospheric pressure is utilized to lift the fluid in the well. The same effect is obtained when flowing a well through open tubing or casing. In using a surface bean this energy of expanding gas is wasted into the flow lines beyond the bean, because the fluid has reached the surface by the time the restriction is reached and the work of the gas performed. The bottom bean affords an efficient use of the expanding force of gas, utilizing less gas to raise the same amount of oil, hence allowing for lower gas-oil ratios. The flow restriction being at the entrance to the flow string, a more uniform mixture of gas and oil enters the tubing and a steadier backpressure is held on the well. The uniform mixture and high velocity attained while flowing through the bean, which is above the critical velocity required to suspend a spray condition of gas and oil, prevent slippage of gas, surging and heading with its resultant strain on the casing. The advantageous conditions allow positive control of production in gas-lift wells within limits set by the bean size and amount of input gas; and probably help to prevent sanding up of a well and the coning

Jan 1, 1931

By S. A. Levy, J. D. Wood, J. F. Libsch

A study of the preparation and characteristics of a sevies of Fe-C-N alloys has been conducted. X-ray, microhardness, and metallographic data from a series of single-phase alloys produced by controlled nitriding of carburized foils are reported. The existence of a, y&apos;, and E carbonitride has been confirmed and it has been found that y&apos; is the hardest of these three phases. These results have been used to interpret the structures observed in nitrided steels. ThIS paper represents the second phase of a three-part study concerning combined nitriding and induction hardening. The first part&apos; reports the engineering properties (depth hardness, fatigue, corrosion, and tempering resistance) obtained when seven different steels were subjected to the combined surface hardening treatment. The present paper concerns the nature of a series of single-phase alloys prepared by controlled nitriding of carburized foils. The objective was to simulate the various layers present in the as-nitrided steels. A third paper will report data concerning induction hardening of the foils and will attempt to set forth a mechanism for the high hardness obtained with the combined treatment. Studies of nitriding generally fall into three categories. The first were performed with bars using conventional nitriding procedures, thus yielding a nitrogen gradient and a series of phase layers near the surface.2-6 Such studies were complicated by the presence of the nitrogen gradient, for it was difficult to correlate microhardness and X-ray data with chemical composition. There were always complications due to penetration of the X-ray beam which yielded data influenced by underlying layers. Similar difficulty was experienced in taking hardness readings on a tapered specimen or in isolating various layers by machining. A second group of investigations was primarily concerned with establishment of regions in the Fe-N7,9,10 or the Fe-C-N phase diagram.8 These were performed with powder specimens which were nitrided in am-monia-hydrogen mixtures to produce a series of single-phase specimens. Unfortunately, the powder specimens were not amenable to either microstruc-ture or microhardness study. The third was essentially a compromise of the first two. Bose and Hawkes," using 0.005-in.-thick iron foils, were able to obtain microhardness, microstruc-ture, composition, and X-ray data on Fe-N alloys of eutectoid composition by equilibration in ammonia-hydrogen mixtures at 1290°F. To obtain a better understanding of the nitriding process and the characteristics of the phases in ni-trided plain carbon steels, the present investigation was undertaken. The investigation was patterned after that of Bose and Hawkes with the exception that nitriding was performed at 930°F (below the eutectoid temperature), as in the case of conventional nitriding. In addition to gaining some understanding of the source of high hardness of nitrided and induction-hardened steels, found in a previous study,&apos; this investigation was concerned with the possibility of controlling the phases present in a nitrided case through the use of ammonia-hydrogen mixtures. Knowledge of the properties of each phase and the conditions necessary for its production could make it possible to avoid undesirable surface layers in nitriding. EXPERIMENTAL PROCEDURE Specimen Preparation. A specimen thickness of 0.005 in. was selected to insure that a uniform nitrogen concentration could be obtained in a reasonable length of time by equilibration in an ammonia-hydro-gen atmosphere. The starting material was a vacuum-cast ingot of pure iron, the major impurities of which were: C, 0.003 pct; 0, 0.014 pct; S, 0.004 pct; N, 0.003 pct.* &apos;Compositions are quoted as weight percent except as noted. The ingot was heated to 1500°F in a nitrogen atmosphere and forged to a slab 0.25 in. thick. The material was then reduced to 0.005 in. by alternately cold rolling and annealing in a nitrogen atmosphere at 1600°F. This material was divided into five groups of specimens which, after carburizing, yielded the following carbon contents: 0.003, 0.28, 0.36, 0.46, and 0.74 pct C. The carburizing was performed by the Leeds and Northrup Research Laboratories, using a controlled "carburizing potential" which yielded a uniform carbon concentration throughout the cross section.

Jan 1, 1970

Discussion Of the paper Of GEORGE K. BURGESS, J. J. CROWE, H. S. RAWDON, and R. G. WALTENBERG, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin NO. 93, September, 1914, pp. 2433 to 2437. ALBERT SAUVEUR, Cambridge, Mass.-The Bureau of Standards has once more rendered a public service. Manufacturers and consumers of steel rails alike should welcome the important results now laid before them by Dr. Burgess and his co-workers. Personally I welcome these results all the more that in the past, as some of the members may remember, I have never failed, when occasion arose, to call the attention of rail manufacturers to the importance of controlling the finishing temperature of their rails. The pioneer metallographic work conducted at the South Works of the Illinois Steel Co. in the early &apos;90s clearly brought out the close relations existing between the manufacture, properties, and finishing temperature of steel rails and I think I may say without fear of being contradicted that the results of this early investigation had considerable influence in drawing the attention of manufacturers to the importance of finishing temperature and of heat treatment in general. The results now before us should be, it seems to me, of great value to rail manufacturers in their efforts to produce a better and, above all, a safer rail. It seems to be demonstrated in this paper that there is no difficulty in installing in rail mills pyrometric outfits, making it possible to record, without interfering in the mill operations, the temperature of the rails as they leave the finishing rolls, or of the ingots as they are withdrawn from the soaking pits, or at any intermediate point in the process of manufacture. The inference necessarily follows that manufacturers should see to it that such pyrometric installations are made, in order that they may actually know, instead of guessing at, the temperature of their rails;, and, for obvious reasons, rail consumers should insist upon such installations. In the rolling of heavy sections especially should care be taken to lower their finishing temperature, seeing that the present tendency is to finish them at higher temperature, whereas, owing to the slower cooling of their central portions, which makes for coarseness of grain, they should, if anything, be finished at a lower temperature than lighter rails.

Jan 4, 1915

By Sandip K. Mitra, John E. Dorn

The Basinki-modified Seeger equation for deformation of metals by means of thermally activated intersection of dislocations was used to ascertain the various factors responsible for the strain hardening of poly crystalline aluminum and a series of a solid solutions of magnesium in aluminum. The analyses were based principally on the rate of change of strain rate with stress and the Cottrell-Stokes ratio. From measurements of these quantities on a series of strain-hardened states, the force displacement diagram for intersection, the density of dislocations in the entanglements, and the contributions of the athermal local stress and long-range stress interactions were deduced. Poly crystalline aluminum was observed to have the same force-displacement diagram for intersection as single aluminum crystals, and the corresponding diagram for the magnesium alloys differed in a manner that suggested that small amounts of magnesium may decrease slightly the stacking fault energy of aluminum. Although poly crystalline aluminum had about the same initial density of dislocations as the single crystals, the density of dislocations increased much more rapidly with strain in the polycrystals. This factor and the higher back stresses generated in the poly crystalline aluminum were the major factors responsible for the higher strength of the poly crystalline aluminum, As the magnesium content of the alloys was increased, the initial density of the dislocations also increased. Most of the alloy strengthening arose from this factor; alloying effects due to short-range order strengthening, Suzuki locking, Cottrell pinning, and so forth, were estimated to be quite small. The gveater rate of strain hardening in the alloys was deduced to be due primarily to the greater increase in the density of the dislocations with strain as the magnesium content was increased. It is the purpose of the present investigation to shed additional light on the average plastic behavior of a grain in a polycrystalline aggregate, by analyses, based on dislocation theory, of appropriate experimental test results. These deductions when compared with those from single-crystal data will then serve to illustrate the major items of difference between the plastic behavior of single crystals and the average behavior of a grain in a

Jan 1, 1963

W. G. MATTESON,* Fort Worth, Tex. (written discussion?).-Dr. Brokaw has evidently given a great deal of time and study to this phenomenon and his conclusions seem sound and logical. .Mr. Lee Hager was probably the first geologist of repute to attach any great importance to the occurrence of paraffin dirt in connection with the Gulf Coast oil-producing salt domes. The writer has been reliably informed that through his discussion, the idea was promulgated that the presence of this so-called paraffin dirt was one of the most important and reliable indications of the presence of an oil-producing salt dome. Despite very strong evidence to the contrary, Hager evidently still has considerable confidence in this theory, as brought forth in his discussion1 of Dr. Brokaw&apos;s paper. Halter here gives all the paraffin dirt occurrences known to him, and adds, "Fifteen of these localities, including practically all of the greatest fields, have produced oil in some quantity." . The acceptance of the list of occurrences as submitted by Hager depends upon what material we are justified in including under the term "paraffin dirt." If we agree to a broad classification, whereby paraffin dirt is. to include all spongy, earthy, decomposed, vegetable material, or spongy soil impregnated with the same, then Haggler&apos;s list will have to be not only accepted but perhaps enlarged. On the other hand, if we confine ourselves to a strict interpretation of the substance known as paraffin dirt, based .upon typical occurrences, general understanding, and application, several of Hager&apos;s occurrences will be seriously questioned by many geologists. The typical material is excellently described by Hager as a dirt or soil-like substance "resilient to the step, like rubber, which falls apart in small squares when dug. Intimately mixed with the soil itself and between the cracks and joint planes is a yellow, jelly-like

Jan 11, 1918

By H. O. Hofman

PAGE Part I. Decomposition OF Zinc Sulphate by Heating in Air, . 811 I. Introduction............ 811 II. Zinc Sulphate Used,..814 III. Fumes and Pyrometers,........ 816 IV. Heating Zinc Sulphate—Dehydration,...... 817 V. Heating Zine Sulphate—Decomposition...818 (a.) Beginning of Decomposition..818 (b.) Rapidity of Decomposition,..819 (c.) End of Decomposition..823 (d.) Retardations in Heating.-Curve,..825 (e.) Formation of Basic Salts,..826 Part II. Decomposition OF Zinc Sulphate by Heating with Carbon (Reducing Roast), .830 I. Introduction,........... 830 II. Experiments and Results ,.........832 III. Summay,........... 834 Part 111. Formation of Zinc Sulphate by Roasting,... 834 I. Introduction,........... 834 IT. Description of Blende,......... 836 III. Outline of Operations,.........838 IV. Details of Experiments.......... 839 1. Decrepitation,.......... 839 2. IgnitionPoint,....839 3. Sulphatizing-Roast of Joplin Blende..840 4. Sdphatizing-Roast of Warren Blemde ,..843 5. Sulphatizing-Roast with Addition of Pyrite...848 6. Summary of Sulphutizng-Roasts,....... 854 Part IV. Appendix : Formation of Zinc Ferrate...856 Part I. Decomposition of Zinc Sulphate by Heating in Air. I. Introduction. With the exception of lead sulphate. all common metallic

Jan 1, 1905