Search Documents

By Grover J. Holt

Low grade ores dwarf high grade, tonnage wise. Bigger and improved-design machines feature modern concentrators. Flowsheets becoming more complex.

Jan 2, 1951

By E. R. Buchanan, R. E. Reed-Hill

Cylindrical magnesium single crystals were deformed in torsion. The axis of torsion was the basal pole. Five crystals were deformed to different strains between 0.08 and 1.03 and then sectioned in order to determine their dislocation densities using the transmission electron microscope. The work hardening rate of all specimens was at least an order of magnitude higher than that normally associated with easy glide in a tension test and comparable to that obserzed in stage B of a tension test. The correspondence between stage B in a tension test and the initial stages of a torsion test is believed to result from the fact that in both cases deformation occurs in a structure containing roughly equivalent densities of the dislocations associated with the three basal slip vectors. THERE are three basic ways of changing the shape of a crystal using slip dislocations. The crystal can be sheared along a slip direction in a slip plane; it can be bent about an axis in the slip plane normal to the slip direction; and, if the slip plane contains multiple slip directions, it can be twisted or rotated about the slip plane normal. Of the three processes, generally known as translational, flexural, and rotational slip, only rotational slip has not been extensively investigated. The object of the present research was to obtain basic information about this phase of crystalline plasticity. This paper is concerned with some aspects of the stress-strain curves obtained by twisting magnesium crystals about their basal poles. Magnesium was selected for four reasons. One, its recovery rate at room temperature is relatively low. Two, single crystals may be easily grown. Three, at room temperature the critical resolved shear stress for basal slip is about two orders of magnitude lower than that for nonbasal slip, so that rotational slip might be expected to occur primarily by basal slip. Finally, relationships between flow stress, shear strain, and dislocation density have been determined for tensile deformation of magnesium crystals,' thereby providing a basis of comparison for the torsional results. EXPERIMENTAL PROCEDURES Crystals were grown from 0.5 in. diam extruded sublimed magnesium rod furnished by the Dow Chemical Co. who reported that it contained in weight percent less than 0.0003 Al, 0.01 Ca, 0.01 Cu, 0.0012 Fe, 0.001 Mn, 0.0005 Ni, 0.003 Pb, 0.001 Si, 0.01 Sn, and 0.02 Zn, with the balance magnesium. All crystals were grown in a dried argon atmosphere using Jill-son's2 modified Bridgman technique. Two different methods were used to obtain crystals with the basal plane normal to the specimen axis. These included direct growth from seeds of the proper orientation, and spark machining (trepanning) of 0.5 in. diam cylinders from larger (1.5 in. diam) randomly grown crystals. The crystals thus produced were polished in a 20 pct HC1 water solution and then etched in a 1 pct HC1 water solution to develop etch pits lying in rows parallel to the basal plane trace. The crystals were then revolved about their axes on the stage of a low-powered microscope. Torsion specimens were prepared only from those crystals whose axes were normal to the rows of etch pits. It is estimated that this simple orientation method was accurate to about 51 deg. 1.625 in. long cylinders were next cut from these selected crystals and then acid machined in a 20 pct HC1 water solution into torsion specimens with a 1 in. long by 0.30 in. diam reduced gage section. Following this, they were annealed in air at 400°C and furnace cooled to room temperature. The specimens were given a final polish in a 10 pct HC1 water solution, rinsed in ethanol, dried, and cemented into brass grips with an epoxy resin. In addition to the torsion specimens, several tensile specimens with their basal planes at 45 deg to the stress axis were also prepared with similar dimensions except that the gage sections were increased to 4 in. in length. The torsion specimens were tested in the apparatus

Jan 1, 1970

By R. P. Rothwell

Jan 1, 1885

By Frederick Laist

Introduction IN a leaching process, having obtained the copper in solution, the choice of the precipitation method is influenced y the following factors: 1. Availability of precipitant. 2. Adaptability to the leaching process. 3. Final product desired. 4. Regeneration of leaching solutions. 5. Fouling of solutions. There are three general classes of precipitation methods: 1. The use of iron, scrap or sponge. 2. Electrolytic deposition. 3. The use of some gas or reagent y which the copper is obtained, usually in the form of an intermediate precipitate which requires further treatment. For example, the precipitation of the copper as Cu2Cl2 from chloride solutions, with SO2 gas. The use of iron is adapted to almost any process. It has the great advantage of extreme simplicity, and the recovery of the copper and any values present in a highly concentrated, easily treatable form. The disadvantages are the cost in isolated places, the uncertainty of the scrap-iron market, and the fouling of the leaching solutions. The latter is a serious factor, When a reagent such as salt is used in them, which makes necessary their re-use. Where applicable, electrolytic deposition is very attractive. The copper is obtained in a form directly marketable, there is a regeneration of acid amid no fouling of solutions. Unfortunately, chloride solutions do not lend themselves to electrolysis. An entirely satisfactory anode material has not yet been discovered, although magnetite, apart from being rather brittle, seems to answer the requirements fairly Well.

Jan 7, 1914

SALT LAKE CITY MEETING The One Hundred and Eighth Meeting of the Institute, for the presentation and discussion of technical papers, will be held at Salt Lake City, Utah, August 10 to 14, 1914. ALL PAPERS TO BE PRESENTED AT THIS MEETING MUST BE IN THE HANDS OF THE SECRETARY ON OR BEFORE MAY 31, 1914.

Jan 3, 1914

By G. H. Wigton

The oxidized ores of the Chief Consolidated Mining Co., in the Tintic mining district, have never yielded to metallurgical treatment by any standard method except smelting. These ores occur in comparatively small, irregular, siliceous replacements in limestone, and carry silver, lead, and gold as the principal valuable metals. But smelting methods are unsatisfactory, as the lead smelters heavily penalize the largc amount of silica in the ore, and the copper smelters do not pay for the lead in the ore; therefore, an alternative treatment method was sought. In 1916, a metallurgical research department was organized under the direction of the writer. Many standard metallurgical methods were investigated but, on oxidized ore, none yielded extraction great enough to make its use feasible. During some chloridizing-roasting experiments in 1916, made in an assay muffle, the writer noted that large proportions of the silver, lead, and gold were volatilized from certain oxidized ores. The possibility of volatilizing the metals and collecting them in the form of a concentrated fume was then studied. But, as it was shown that satisfactory chloride-volatilization would be limited to a furnace feed with a high fusing temperature of the non-volatilizable constituents, and as the results obtained in a rotary kiln with the admixture of common salt with the ground ore were inferior to muffle tests, further volatilization experiments were discontinued until 1920. During this internal, an expcrimental sulfidizing and flotation plant was operated. After the cessation of attempts to float the oxidized minerals, chloride-volatilization experiments .were resumed. The highly infusible flotation tailing from the operation of the flotation mill was used for furnace feed. The first tests made on flotation tailing mixed with 10 per cent, common salt showed nearly complete lead and gold volatilization but considerably less volatilization of silver than in muffle tests. In attempts to increase the silver extraction, the percentage salt in the furnace feed was varied, and it soon became apparent that the use of smaller percentages of salt raised the fusion temperature of the furnace charge and thus

Jan 1, 1926

By Homer W. Riley

ANTHRACITE SMALL power-driven, toothed, cast-iron rolls were used first to break anthracite in 1844. Prior to that time, men with hammers, who stood on perforated cast-iron plates, broke the large lumps into commercial sizes. In order to convert run-of-mine into the various sizes required by the anthracite industry, about 20 million tons must be broken, annually, into smaller sizes. This phase of anthracite preparation is of major importance, because the degradation accompanying reduction in coal sizes should be kept at a minimum. The exclusive use of toothed rolls for that purpose indicates that comminution by rolls is the best solution of the problem. Many improvements have been made in tooth design, but the most important was a reduction of the peripheral speed of the rolls from 1000 to 300 ft. per minute. The higher speed was based upon and approximated the velocity of a falling piece of coal when it entered the rolls, Exhaustive roll tests at the slower speed showed that the same size reduction could be affected with less degradation. The adoption, therefore, of slow-speed, compound geared rolls, especially for breaking the larger sizes, became quite general after 1912. A high-speed roll is shown in Fig. 1 and a slow-speed roll in Fig. 2. Anthracite Crushing Problems.-Crushing anthracite presents the problem of selecting a series of rolls that will produce the greatest percentage of the prepared sizes of nut and over. The size distributions to be expected are shown in Table 1. Coal breaking and crushing practices in anthracite breakers involve the use of equipment for comminuting the following classes of material: 1. Run-of-mine-plus 6 ½ -in. coal. 2. Sized coal-steamboat, broken, egg, stove, nut, and pea. 3. Flat coal--coal that is flat and hence not suitable for the market. 4. Bone--a piece of laminated coal and slate, crushed for the purpose of reclaiming the coal. 5. Breaker refuse, reduced to a size suitable for flushing into a mine for back-filling purposes.

Jan 1, 1950

By E. C. Reed

Drilling activity in Nebraska continued to decline during 1944. Nine tests for oil and gas were completed during the year and four wells were drilling at the close of the year. Four wells were drilled in Richardson County, three in Hitchcock County and single wells were drilled or drilling in Butler, Gage, Holt, Nemaha and Scottsbluff Counties. Only one of the completions resulted in commercial pro- duction, the others being abandoned as dry holes. A number of stratigraphic test holes were drilled in the state by the Stanolind Oil and Gas Co. and the Sinclair-Prairie Oil Co., in Johnson, Otoe, Chase, Dundy and Garden Counties. No new fields were discovered during 1944 but the limits of the Barada field, Richardson County, was extended a short distance southward. Oil production continued to drop and about two thirds as much oil was produced in 1944 as in 1943.

Jan 1, 1945

POSITIONS VACANT A steel manufacturing company is desirous of securing an assistant superintendent for its plant. Experience in open-hearth plants and in rolling mills particularly desirable. No. 112. Opening as assistant superintendent of a non-ferrous smelting plant. Man with metallurgical experience preferred but chief essential is ability to handle men. No. 114. ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, aged 41, mining engineer, manager or general superintendent, 20 years' experience, 10 years in Mexico, 5 years Western States, 5 years abroad. Guarantee results, fluent. Spanish, excellent references. New York interview. No. 282. Member, technical mining graduate, 10 years' experience, especially in design, erection, construction and purchase of power and mining equipment and supplies, desires position in purchasing department. Married, aged 32, employed at present, references furnished. No. 295.

Jan 7, 1916

ENGINEERS AVAILABLE (Under this heading mill be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, technical graduate, aged 35, with experience as surveyor, sampler, assayer, and cyanide superintendent, desires position as engineer or cyanide operator.. No. 157. Member, technical graduate, aged 34, with 12 years' experience, including engineering, construction, and management of gold, silver, copper, and quicksilver mines, desires position of 'superintendent of gold or silver property. No. 158. Technical graduate, aged 24, with experience as mine surveyor and instructor in chemistry, desires position as instructor in mining. No. 159. Member, aged 29, technical graduate, with experience in exploration, prospecting, mining, concentration, smelting, and as assayer and chemist, engineer, and draftsman (smelter) in United States, Canada, Africa, South America., and Australia, desires to become connected with a firm of consulting engineers. Speaks Spanish. No. 1130.

Jan 11, 1914

PERSONAL (Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period June 10 to July 10: J. C. Ralston, Spokane, Wash. E. P. Ashmore, So. Porcupine, Ont., Can. William H. Yeandle, Jr., Mexico City, Stuart Croasdale, Denver, Colo. Mexico. W. E. Hopper, Houghton, Mich. W. C. Minsch, Mexico City, Mexico. D. W. Brunton, Denver, Colo. H. V. Winchell, Minneapolis, Minn. Fred Crabtree, Pittsburg, Pa. W. G. Swart, Denver, Colo. Robert S. Lewis, Salt Lake City, Utah. D. F. Schindler, Madison, Wis. Noel Cunningham, Timmins, Ont., Can E. R. Pettebone has just been elected a Trustee of the Pennsylvania State College, being supported by the votes of the delegates of the Pennsylvania Anthracite Local Section of the Institute and the Engineers' Society of Northeastern Pennsylvania.

Jan 8, 1914

By F. F. Aplan

The past year has been another year of vigorous fundamental research in mineral processing as evidenced by the active publication of results, particularly in Germany, Japan, United Kingdom, United States and USSR. It was also noteworthy for several significant meetings and conferences. The Basic Science sessions at the AIME Annual Meeting continued to attract an increasing audience and the sessions were especially notable for the active discussion of papers. The third Engineering Foundation Conference on Particulate Matter Systems,1 chaired by F. F. Aplan, was held in Milwaukee in August and attracted over 100 experts from five continents. Sessions at this week-long conference covered comminution, particle characterization, separation of fine particles, fluid-solid separations as applied to pollution control, flotation kinetics, particle-particle interactions and particle agglomeration. This popular conference will be continued under John Karpinski of Bethlehem Steel Corp. as 1968 chairman.

Jan 2, 1968

By L. W. Bahney

FREQUENTLY in using a thermo-electric pyrometer for measuring the temperature of a furnace, a hole is drilled at the back or side of the furnace, through which is introduced the tube containing the thermo-couple. At times the couple is left almost where it drops, for the reason that it soon becomes too hot to be handled easily, and the space at the back or side of the furnace may be so small and uncomfortably hot that an easy and accurate adjustment is nearly impossible. In order to overcome this clumsy and unscientific method of using the thermo-electric pyrometer, I designed an adjustable stand, to hold the clay or quartz tube unclosing the platinum and plati-num-rhodium leads that constitute the couple of the Le Chatelier thermo-electric pyrometer. This stand also allows an easy and rapid adjustment of position to varying heights and angles, as may be desired for special reading. This stand is illustrated in Fig. 1. The couple in the tube might be of better service if the tube were held a little higher above the charge in a roasting-dish, changing the height and angle if desired. The stand, made of 1.5-in, water-pipe and mounted on casters, is heavy enough so it cannot be tipped over easily. It is adjusted to any position, and has a universal clamp which holds the clay or quartz protecting-tube. To avoid disturbing the wires of the couple at the cold junction each time the tube is moved, the cooling-bottle sets in a wire basket so placed that it moves forward or back with the couple. To overcome the necessity of leveling and adjusting a galvanometer at each furnace, a switch-board is used to connect

Jan 1, 1910

By Lloyd Pollish, Robert N. Breckenridge

SUCCESS in any underground mining operation is determined by accessibility of the orebody, which in turn is dependent upon maintenance of passageways to the mining zones and temporary support of the voids caused by extraction of ore. This is accomplished by one or a combination of the following methods: timbering, back-filling, pillaring, or, more recently, rock bolting. Timbering has usually been the principal means of maintaining these underground openings necessary for mining operations. Timber, however, does not prevent ground movement beyond the scope of localized sloughing, which is indicated by the gradual failing of the timber itself. Besides this, timbering has always been a costly process, and with the decline of available supplies of timber close to the mining areas, mining men have constantly sought other methods of controlling ground. Rock bolting is now replacing timbering at an ever increasing rate. Experience has proved that this form of ground support is just as applicable to blocky igneous rock as to stratified rock. Besides preventing sloughing of the walls and back of underground openings, Fig. 1, rock bolting has a stabilizing effect on the surrounding ground in much the same manner that steel reinforcing rods add to the strength of concrete structures. Further, rock bolting is flexible and may be applied to any shaped excavation, whereas timber sets are in a fixed pattern and the ground must often be changed to conform with this pattern. Rock-bolting installations were made in metal mines of the Northwest as early as 1939. An exhaust air crosscut was driven that year in one of the Butte mines of the Anaconda Copper Mining Co. The crosscut was rock-bolted and gunited at the time it was driven and is still being used to exhaust hot humid air from the 3400 level of the Belmont mine. It is interesting to note that no sloughing or caving has taken place in the 14 years it has been open. Even though these early installations of rock bolts were successful, few men recognized their potentiality until recent years, when the coal mines started their programs of mechanization and the great trend toward roof bolting began. In some areas of the Northwest stopes that previously required heavy timbering and close backfilling are now being mined by the more economical cut-and-fill and shrinkage methods. When used in conjunction with timbering, rock bolting increases the efficiency of the operation by decreasing hanging wall dilution and by making it possible to blast larger rounds. Most of the rock bolts installed to date in mines of the Northwest have been the 1-in. diam slot and wedge type, but there has been a recent trend to- ward using the 3/4-in. diam expansion shell bolt shown in Fig. 2. In addition to these commercially manufactured steel bolts, wooden bolts have been used with considerable success by the Day Mines of Wall'ace, Idaho. Installation of the slot and wedge type requires three distinct operations, with tools for each operation: 1—drilling the hole to proper diameter and depth, 2—setting the bolt, and 3—tightening the nut. Holes are drilled and bolts set with pneumatic rock drills. A number of setting or driving tools have been used successfully, but most follow the same general pattern. Usually the driving tool is designed to accommodate a short length of drill steel on one end and the rock bolt on the other end. In this manner the hammering effect of the rock drill is transmitted through the steel and driving tool to the bolt. When machines not having stop rotation are used, slippage is allowed between the driving tool and bolt or between the drill steel and driving tool. The rock bolt nuts are tightened either with pneumatic impact wrenches or with hand wrenches. Impact wrenches are desirable because they are faster and assure adequate tightness. Expansion shell bolts have the following advantages over slot and wedge rock bolts: 1—No special equipment other than a wrench is needed for their installation. 2—Installation is faster. 3—They are removable. 4—Holes need not be drilled to a specific depth as the expansion shell will anchor anywhere along the length of the hole. These advantages are offset somewhat by the lesser strength of the bolt, since expansion shell bolts are generally made from 3/4-in. diam steel as compared to 1-in. diam steel for the slot and wedge type. One manufacturer, however, is now fabricating expansion shell rock bolts from steel of high tensile strength, which gives this ¾-in. bolt a much greater strength than that of the mild steel bolt. Table I illustrates tests made by the Anaconda Copper Mining Co. to determine the proper hole size to use with various types of bolts and to determine

Jan 1, 1955

By Rudolph G. Wuerker

THE Krupp-Renn Process,[1] has been successfully used to treat low-grade iron ores, laterites, titaniferous sands, and other minerals, and before World War I1 25 units were built by the Krupp-Grusonwerk, Magdeburg, Germany. J. J. Howard[2] has shown theoretical advantages of the pyro-metallurgical treatment over conventional approaches; and the process was described by R. Durrer[3].

Jan 1, 1951

By Richard P. Rothwell

The communication which I hare to lay before my fellow-members of the Institute, is no elaborate paper, nor the statement of any great discovery; it is simply the record of convenient methods of conducting topographical survey?, and of keeping the notes of the same; methods that have grown out of practical experience, and have saved me many a day's labor by facilitating office and field work, and at the same time secured a greater degree of accuracy than is obtained by the methods now in general use. I assume it as granted that no topographical map is worthy of the name, except it represent the elevations and depressions of the surface by means of horizontal or contour lines. In the Ordnance Survey of Great Britain, the contour lines are traced for every fifty feet vertical height, I believe, by running out the line with level and compass through all its meanderings on the surface; this, of course, is a very tedious, though accurate process, but " in the woods," where many of our surveys have to be made, it would be practically impossible. Some time ago, I made an extensive and quite elaborate topographical survey and contour map of the southern portion of the Cahaba coal-field, in Alabama, the object of the survey being to

By Richard P. Rothwell

THE communication which I have to lay before my fellow-members of the Institute, is no elaborate paper, nor the statement of any great discovery ; it is simply the record of convenient methods of conducting topographical surveys, and of keeping the notes of the same; methods that have grown out of practical experience, and have saved me many a day's labor by facilitating office and field work, and at the same time secured a greater degree of accuracy than is obtained by the methods now in general use. I assume it as granted that no topographical map is worthy of the name, except it represent the elevations and depressions of the surface by means of horizontal or contour lines. In the Ordnance Survey of Great Britain, the contour lines are traced for every fifty feet vertical height, I believe, by running out the line with level and compass through all its meanderings on the surface ; this, of course, is a very tedious, though accurate process, but "in the woods," where many of our surveys have to be made, it would be practically impossible. Some time ago, I made an extensive and quite elaborate topographical survey and contour map of the southern portion of the Cahaba coal-field, in Alabama, the object of the survey being to

Jan 1, 1875

By H. B. Muller

Single stage autogenous grinding of run-of-mine ore was selected by Broken Hill South Ltd., parent Company of Cobar Mines Pty. Ltd. for the concentrator to treat 60,000 tons per four weekly period of copper and complex copper-lead-zinc sulphide ores from the C.S.A. Mine at Cobar, Australia. Ore is mined by mechanised horizontal cut-and-fill stoping and is prepared for grinding by crushing under- ground in a 60 in. x 48 in. jaw-crusher set at 5 in. closed side setting. The ore is reduced to 80% minus 76 microns in two parallel sections each of one 22 ft. dim. x 7 ft. long autogenous grinding mill, powered by a 1,250 H.P. motor, operating in closed circuit with a single stage 20 in. dim. cyclone. Broken Hill South's original concept of the concentrator required the maximum use of reliable instrumentation, centralised control, and the minimum of manning. To achieve this objective the control room, housing the process recorders, alarms, closed circuit television monitors and all the control equipment, overlooks the grinding and flotation sections, and the whole plant is serviced by a public address system. The grinding units and associated equipment are located in the open and are serviced with the aid of a mobile crane and a mobile hydraulically-operated liner lifting device.

Jan 1, 1970

By W. R. Foster, J. M. McMillen, A. S. Odeh

The complete equations of average linear momentum balance for a single-phase fluid in an incompreisible, homogeneous, porous medium are derived. The derivation begins with Euler's equation of motion for a continuum and uses an integral transform recently developed by Slattery. 7 For steady flow of a compressible, Newtonian fluid, the usual equations of motion result. For transient flow, the space-time description of the pressure is determined in the lowest approximation by the telegrapher's equation. From the analysis a new phenomenological coefficient results which connects the viscous traction to the deriv ative of the linear momentum density. The magnitude of this coefficient determines the velocity of sound through the pore structure in this approximation to the pressure field. INTRODUCTION The modification of Darcy's law of momentum balance for steady, single-phase flow through porous media has been discussed for many years. The first modification was suggested by Forcheimerl who added terms of higher order in the velocity. These can be expected to appear because the underlying microscopic equations of momentum balance are themselves nonlinear in the point velocity field. The Reynolds tensor pvv, which represents the convective flux of momentum density, appears in the momentum balance equation. Only in rectilinear flow (parallel stream lines) does the divergence of this tensor vanish. Since the steady flow stream lines in most porous media are not parallel, nonlinear dependence of the pressure gradient on the velocity should naturally appear. This nonlinearity has nothing to do with turbulence in the ordinary sense of random fluctuations in the pressure and velocity fields. It arises simply because the stream lines converge and diverge, even for steady flows. Klinkenberg2 demonstrated that the permeability coefficient in Darcy's law depends on the absolute pressure or, alternatively, on the density field. However, because he neglected inertial terms of the Forcheimer type, his correction coefficient could not be represented by a constant but tended toward a constant as the velocity decreased. Forcheimer's and Klinkenberg's modifications can be combined in a rigorous way to account for both inertia and slip during steady flow. This will be shown in a future paper. The transient change of pressure in porous media has been described by the diffusion equation.3 This form results from eliminating the velocity and density fields from a combination of the equations of motion in the form of Darcy's law, the continuity equation and an equation of state. Fatt4 suggested that the cause of deviations from the prediction of the diffusion equation for pressure transients lies not in the choice of Darcy's law as the equation of motion but on the existence of dead-end pores which might invalidate the averaged equation of continuity. On the other hand, Oroveanu and Pascal5 noted chat the time derivative of the momentum density must be included in the equations of motion since this measures the local rate of change of momentum density. Their differential equation for pressure is the telegrapher's equation (neglecting gravity). However, their form of this equation predicts that the speed of pressure propagation through the pore structure is the same as that through the bulk fluid. M. K. Hubbert6 attempted a derivation of Darcy's law by volume averaging the Navier-Stokes equations. Since these equations represent momentum balance at a point within an open set of points containing the fluid itself, Hubbert's volume averaging cannot lead to tenns involving transfer of momentum between the fluid and the walls of the pores. Once these viscous tractions are lost by choosing a control volume containing only fluid, they cannot

By R. J. Wygal

A method is presented by which homogeneous, isotropic, and reproducible aggregates of particles such as glass beads, sand, ground glass, etc., may be prepared simply and quickly by using a "particle distributor". Several applications of the packing method to the construction of model reservoirs are described. The flow characteristics of these packings me given. Some factors which limit the usefulness of unconsolidated packs for simulating reservoir rock are overcome through artificial cementation of the aggregates. INTRODUCTION Many laboratory studies of porous media are based on experiments using test packs of sand, glass beads and other granular materials. More confidence can be had in the results of such studies if the test packs are known to have uniform properties throughout, to be mechanically stable and to be accurately reproducible. This paper presents a method by which such packs of a variety of shapes and sizes may be constructed using a particle distributor. Some factors which limit the usefulness of unconsolidated packs as a means for simulating reservoir rock are described. A method of overcoming these limitations, which involves artificial cementation of the packs, is presented. DEVELOPMENT Particles packed by the tamping or vibrating techniques are usually either non-uniform or mechanically unstable. An invention by Currie and Gregoryl overcomes these difficulties to some extent. The invention is based on the use of a stream of falling particles impinging on and passing through a distributor matrix of several layers of closely spaced spheres. The particles are well dispersed by numerous collisions with the spheres. They become homogeneously distributed at some distance below the distributor matrix and at that position are collected in the sample container. This apparatus, however, was found to be ineffective when small particles were used since small particles accumulate on the top surfaces of the spheres. An improved distributor matrix was made, first in the form of a stack of five sieves, and then in the more adaptable form of spaced layers of wire screen. Fig. 1 shows a longitudinal view through a five-layered distributor of eight-mesh wire screen. This device gives excellent results.* Fine particles pass through the distributor with very little hold up. The fine structure of the wire matrix with its many deflecting surfaces ensures good particle distribution. There are no dead areas immediately below the screen as were sometimes observed to occur below a matrix of spheres. Using such a device, 20-30 mesh sands were packed to a porosity of 32.1 per cent at rates varying from 0.17 to 6 lb/rnin. The lowest porosity achieved by tamping small increments of similar sands into a container was 33 per cent. Motion pictures at 3,000 frarnes/sec of the surface of a growing pack of 2-3/4 mm glass beads have helped to show the mechanism by which packs of low porosity are obtained. The beads, although packed at the rate of 5 lb/min, were observed to hit the pack surface singly, for the most part, and at well spaced points of impact. Part of their energy is transferred to surface beads which are thereby