Search Documents

By Kenneth L. Adams

10.3-1. Introduction. Equipment replacement or maintenance is of major concern to every company today. It can be the difference between an efficient and profitable operation or an inefficient and struggling one. Mining equipment, as everyone knows, will not last forever. Some equipment becomes obsolete before it wears out while some may be doing its intended job, yet not economically. It is a major problem for management to make the decision as to whether a piece of equipment should be repaired or replaced. There are numerous approaches to this problem; using formulas, charts, and graphs. These would be very good if all conditions were stable. Since conditions and requirements are constantly changing, an accurate observation cannot be derived from a set formula. A formula does, however, serve as a reminder to include most of the items that should be considered when evaluating old and new equipment. In the field of mining there are several questions which enter into the reasoning that are difficult to put into an equation. Some of these are: 1. Will the present equipment produce the required output of the mine, or an increase if necessary? 2. Are reserves adequate to support the purchase of new equipment? 3. Can the old equipment be repaired to efficiently continue the mining operation? 4. What is the stability of future markets for the product? Depreciation rate, or the write-off life, is a factor that can directly effect decisions on replacement. If the initial life expectancy is too long and the price of equipment is not written off when discarded, then the original investment has not been recovered. If the write-off time is too short, then the equipment is written off before replacement is even considered. In this case, the depreciation accrual is usually used to finance some other phase of the operation. In view of the increasing prices, the amount of depreciation fund is generally too small for much incentive to replace an older unit

Jan 1, 1968

By G. C. Broadhead

THE lead district of Southeast Missouri covers an area of over 3000 square miles, including Maries County on the west, Jefferson on the east, Franklin on the north, and part of Madison on the south, or parts of ten counties. A general section of the rocks of the southeast part of this region would be about as follows, numbering from the top 1. Sandstone (the second of Missouri geologists), - 20 feet. 2. Cbert beds-beds of passage below, - 125 feet 3. Magnesian limestone, chert, and quartzite, - 100 to 300 feet 4. Lower magnesian limestone, - 100 to 150 feet 5. Gritstone and lingula beds, - 50 feet 6. Ozark marble beds, - 5 to 20 feet 7. Sandstone and conglomerate, - 5 to 90 feet 8. Porphyry, Archaean. 9. Granite, The thickness is approximate, for it is not possible to obtain the correct thickness of the various beds. No. 1 may be seen as de¬tached outliers or loose masses of a hard sandstone or quartzite, and is found on the hilltops in the southern part of Madison County, in like topographical position in Reynolds County and the western part of Washington County. No. 2 consists of alternations of chert, clay, and quartzite. It is the formation which contains most of the limonite deposits of Central and Southern Missouri. In Reynolds County shafts have pene¬trated it 75 feet. Outcrops there and in Madison would indicate it to be at least 125 feet thick. Fossils obtained in various places prove it clearly to be of the age of the calciferous sandrock of the New York system, and Nos. 1 and 2 may also be referred to the age of the second sandstone of Missouri. No. 3 consists chiefly of thick beds of ash, drab and flesh-colored magnesian limestone, both coarse and fine-grained. These beds, where they occur, in Washington, Jefferson, and the southern part of Madison Counties, contain a good deal of quartz in drusy cavities. In Washington County the limestones are beautifully ramified by a system of connected drusy cavities generally lined with minute quartz crystals arranged in botryoidal and mammillary forms, and called u mineral blossom " by the miners. This is the lead-bearing rock of Washington County, but in the southern part of Madison it does not appear to be galeniferous. It is also undoubtedly the equivalent of

Jan 1, 1877

By G. C. Broadhead

The lead district of Southeast Missouri covers an area of over 3000 square miles, including Maries County on the west, Jefferson on the east, Franklin on the north, and part of Madison on the south, or parts of ten counties. A general section of the rocks of the southeast part of this region would be about as follows, numbering from the top: 1. Sandstone (the second of Missouri geologists),.... 20 feet. 2. Chert beds—beds of passage below,...... 126 " 3. Magnesian limestone, chert, and quartzite,. .. 100 to 300 " 4. Lower magnesian limestone,......100 to 150 " 5. Gritstone and lingula beds,....... 50 " 6. Ozark marble beds,........5 to 20 " 7. Sandstone and conglomerate,. .. .. 5 to 90 " 8. Porphyry, Archæan 9. Granite, The thickness is approximate, for it is not possible to obtain the correct thickness of the various beds. No. 1 may be seen as detached outliers or loose masses of a hard sandstone or quartzite, and is found on the hilltops in the southern part of Madison County, in like topographical position in Reynolds County and the western part of Washington County. No. 2 consists of alternations of chert, clay, and quartzite. It is the formation which contains most of the limonite deposits of Central and Southern Missouri. In Reynolds County shafts have penetrated it 75 feet. Outcrops there and in Madison would indicate it to be at least 125 feet thick. Fossils obtained in various places prove it clearly to be of the age of the calciferous saudrock of the New York system, and Nos. 1 and 2 may also be referred to the age of the second sandstone of Missouri. No. 3 consists chiefly of thick beds of ash, drab and flesh-colored magnesian limestone, both coarse and fine-grained. These beds, where they occur, in Washington, Jefferson, and the southern part of Madison Counties, contain a good deal of quartz in drusy cavities. In Washington County the limestones are beautifully ramified by a system of connected drusy cavities generally lined with minute quartz crystals arranged in botryoidal and mammillary forms, and called " mineral blossom " by the miners. This is the lead-bearing rock of Washington County, but in the southern part of Madison it does not appear to be galeniferous. It is also undoubtedly the equivalent of

By J. C. Febles

HISTORY. THE use of iron for the precipitation of copper was known at least as early as the fifteenth century. Both Paracelsus and Basil Valentine refer to it in their writings, as early as 1500 A. D. It was used in Peru for this purpose prior to 1637, and at Rio Tinto, Spain, as early as the sixteenth century. The statement has been made repeatedly that in the early history of the mining industry at Butte, the practicability of this method of recovering copper from solution was overlooked, and that enormous quantities of copper-bearing water were allowed to go to waste, the copper in which might easily have been recovered at small cost; and .that this oversight on the part of the mine operators was due to ignorance of this method of recovering copper. As a matter of fact, very little copper-bearing mineral was encountered in the mines of Butte until a depth of 400 or 500 ft. bad been reached, and in many cases much greater depths were necessary to reach the copper-bearing zone. The water encountered in the upper levels (although in most cases quite highly mineralized) contained little or no copper, and it was only after considerable areas of copper-bearing ore' had been uncovered and developed that copper sulphate began to appear in the mine water in any considerable quantity. In fact, the first water that was observed to contain copper carried it in such small amounts as to be of little or no importance. It was only after years of underground work had opened extensive areas of stopes, drifts, and other underground workings, these being subsequently filled with waste, nearly all of which contained small copper values, which became oxidized by exposure to the air and were acted upon by the slowly percolating mineral water, that the recovery of copper from mine water became commercially important.

Jan 7, 1913

By J. C. Febles

HISTORY. THE use of iron for the precipitation of copper was known at least as early as the fifteenth century. Both Paracelsus and Basil Valentine refer to it in their writings, as early as 1500 A. D. It was used in Peru, for this purpose prior to 1637, and at Rio Tinto, Spain, as early as the sixteenth century. The statement has been made repeatedly that in the early history of the mining industry at Butte, the practicability of this method of recovering copper from solution was overlooked, and that enormous quantities of copper-bearing water were allowed to go to waste, the copper in which might easily have been recovered at small cost; and that this oversight on the part of the mine operators was due to ignorance of this method of recovering copper. As a matter of fact, very little copper-bearing mineral was encountered in the mines of Butte until a depth of 400 or 500 ft. bad been reached, and in many cases much greater depths were necessary to reach the copper-bearing zone. The water encountered in the upper levels (although in most cases quite highly mineralized) contained little or no copper, and it was only after considerable areas of copper-bearing ore had been uncovered and developed that copper sulphate began to. appear in the mine water in any considerable quantity. In fact, the first water that was observed to contain copper carried it in such small amounts as to be of little or no importance. It was only after years of underground work had opened extensive areas of stopes, drifts, and other underground workings, these being subsequently filled with waste, nearly all of which contained small copper values, which became oxidized by exposure to the air and were acted upon by the slowly percolating mineral water, that the recovery of copper from mine water became commercially important.

Jan 7, 1913

By C. A. Wert, M. G. Coleman

The Zener relaxation in alloys in the a! solid-solution region of the Cu-Ni-Zn ternary system has bear investigated. Of the binary solid solutions that bound this region, Cu-Zn and Ni-Zn exhibit measurable Zener peaks whereas Cu-Ni does not. At constant atomic percent copper, the Peak height drops uni.forinly from the value in the Cu-ZTL binary to zero in CIA-Ali. The cariation of peak ternperatuve with composition is linear. At constant atomic percent zinc, the peak height in the ternary alloys goes through a large maximum as compared with the binary values. The temperature of these peaks varies smoothly with composition. The half-width of the peaks in the ter nary alloys, however, are much larger than those in the binaries. A large enhancement of the relaxation strength of the Zener relaxation in ternary Au-Ag-Zn alloys as compared to the relaxation strengths in Au-Zn and Ag-Zn binary alloys was observed by Firson and ert.' Since this effect was unexpected, the present study was devised to investigate whether enhancement of the Zener relaxation in ternary alloys is a general feature or is particular to the Au-Ag-Zn system. We have chosen the Cu-Ni-Zn alloy system for this investigation. Measurable Zener relaxations are observed in both the Cu-Zn and the Ni-Zn binary systems, but not in the Cu-Ni binary system. A large solid-solution region extends to large concentrations of zinc, making it possible to vary composition of the alloys over a wide range without crossing phase boundaries. EXPERIMENTAL PROCEDURE Two series of alloys were prepared. the first at constant atomic percent copper, the second at constant atomic percent zinc. The compositions of these alloys are shown by the circles in Fig. 1. The alloys were prepared by melting the individual components, each of which had previously been vacuum-melted, in an evacuated quartz capsule in an induction furnace at 1500 C. The capsules containing the molten alloys were quenched in water to reduce coring. Any individual melt which exceeded 0.001 pct weight loss was discarded. The ingots were swaged to a 50 pct reduction of area and annealed for 1 week in an evacuated quartz capsule to aid homogenization. The alloys were then

Jan 1, 1967

TO THE BOARD OF DIRECTORS AND THE MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN: Herewith are submitted the report of the Treasurer for the year 1936 and the reports for the same year of the following committees: Admis¬sions, Membership, Papers and Publications, Library, Student Relations, and MINING AND METALLURGY. To these reports you are referred for details of the year's activities. Finances.-Income for the year was $173,091 including an appropria¬tion of $2500 from the Rocky Mountain Fund earmarked to defray expense for official visits to western Sections and student societies. This compares with $141,754 in 1935 and exceeds by more than $50,000 the income of 1933 wherein the low point during the depression was reached. The major items of increase were: $6,700 from current dues; $10,600 in initiation fees and dues of newly enrolled members; $10,800 from the monthly magazine MINING AND METALLURGY. Sundry small declines were offset by minor increases. Expenditures for the year totaled $176,007 compared with $148,361 in 1935. Major increases were $5,700 for MINING AND METALLURGY; $4,000 for TRANSACTIONS and TECHNICAL PUBLICATIONS; $1,500 for meetings; $1,300 for Local Section appropriations; $6,500 for Technical Division expense; $5,000 for Increase of Membership expense; and $2,500 for visits to Local Sections and educational institutions. Comment on several of these items will appear under subsequent heads. Net deficit for the year was $2,915, this sum being made up from the accumulated surplus. It is interesting to observe that the net excess of income over outgo for the five-year period 1932-1936, inclusive, is $760. Membership and Dues.-During the year there was a net gain in membership, including Members, Associates, Junior Members and Junior Foreign Affiliates of 755 (from 7116 to 7871). In addition there was a gain of 616 in Student Associates (from 1004 to 1620). Taking account of small losses totaling 5 in the other grades, the net increase was 1366 bringing the total to 9607, the highest figure reached in the history of the Institute except at the end of 1921 when the total was 9850. In part the gain is accounted for by the smaller number lost by suspension

Jan 1, 1937

By J. C. Febles

The use of iron for the precipitation of copper was known at least as early as the fifteenth century. Both Paracelsus and Basil Valentine refer to it in their writings, as early as 1500 A. D. It was used in Peru for this purpose prior to 1637, and at Rio Tinto, Spain, as early as the sixteenth century. The statement has been made repeatedly that in the early history of the mining industry at Butte, the practicability of this method of recovering copper from solution was overlooked, and that enormous quantities of copper-bearing water were allowed to go to waste, the copper in which might easily have been recovered at small cost; and that this oversight on the part of the mine operators was due to ignorance of this method of recovering copper. As a matter of fact, very little copper-bearing mineral was encountered in the mines of Butte until a depth of 400 or 500 ft. had been reached, and in many cases much greater depths were necessary to reach the copper-bearing zone. The water encountered in the upper levels (although in most cases quite highly mineralized) contained little or no copper, and it was only after considerable areas of copper-bearing ore had been uncovered and developed that copper sulphate began to appear in the mine water in any considerable quantity. In fact, the first water that was observed to contain copper carried it in such small amounts as to be of little or no importance. It was only after years of underground work had opened extensive areas of stopes, drifts, and other underground workings, these being subsequently filled with waste, nearly all of which contained small copper values, which became oxidized by exposure to the air and were acted upon by the slowly percolating mineral water, that the recovery of copper from mine water became commercially important.

Jan 1, 1914

By H. N. Hall

Reservoir and producing characteristics can govern the decision to use either a one-, two- or three-dimensional model for making predictions for gravity-drainage reservoirs. Examples of conditions requiring one-, two- and three-dimensional calculations are given. In 1961 the author presented a method for predicting one-dimensional gravity-drainage performance. This work has been exrendcd to obtain a three-dimensional model, which is described and for which a sample problem is presented. Introduction Many papers on gravity drainage or gas-cap drive'-3 have been presented for conditions where the reservoir is treated as a single areal segment so that, in effect, only one-dimen-sional flow is considered. Other authors'-Q ave given evidence showing that the one-dimensional concept would be unsatisfactory to predict reservoir performance for certain types of reservoirs. Experience has indicated that specific reservoir and producing conditions govern whether one-, two- or three-dimensional concepts must be used as a basis for reliable reservoir performance predictioils. Previously the author presented a paper outlining a method for predicting the performance of gravity-drainage reservoirs.' That paper treated the reservoir as a single areal segment so that it was applicable for only one-dimensional flow. The work has been extended to obtain a three-dimensional model that can be used to predict performance of gravity-drainage reservoirs. Although capable of being three-dimensional, it can be used equally well for one- and two-dimensional predictions. This paper discusses those reservoir and producing conditions governing the choice of model, and also describes a three-dimensional model suitable for predicting reservoir performance in the more complex situations. Discussion The Choice of Model To predict reservoir performance, it is necessary to represent the reservoir by a physical model. A mathematical model, based on the assumed physical model, then is used to predict the movement of oil and gas within the reservoir. The word "model" is used here to connote the combination of both a physical model and a mathematical model based on the physical model. Certain types of reservoir situations may be predicted suitably with a one-dimensional model, whereas two- and three-dimensional models may be required for other situations. This section illustrates reservoir conditions associated with the use of a specific type of model. Many types of reservoir structures are such that gravity drainage possibly could be an important factor in oil production. Production practices, as well as the nature of the structure. can influence the type of model that should be used. obviously, it is impossible to discuss all combinations of reservoir structure and production practices that might be encountered in gravity-drainage reservoirs. The following are typical examples of conditions where a choice must be made among a one-, two- or three-dimensional model to predict reservoir performance satisfactorily. Conditions Requiring a One-Dimensional Model Fig. la shows contours for an asymmetrical anticline in which gravity drainage might be expected to be important. Fig. Ib depicts a cross-section along Line A-A in Fig. la. Existence of a gas cap is a good clue that gravity drainage will be an important factor in producing oil from this type of reservoir. However, it is not essential since a gas cap will form as oil is produced from the reservoir. If the proper combination of reservoir permeability and withdrawal rates is present, the reservoir will behave like a

Jan 1, 1969

The following paper, submitted by the Russian petroleum authorities, was secured through the courtesy of G. V. Ackerman, Vice President of Amtorg Trading Corporation, and N. V. Vannikoff, Representative in the U.S.A. of the United Oil and Gas Industries of the U.S.S.R. It gives an excellent view of the Russian petroleum industry as seen through Russian eyes. Noteworthy is the tremendous area over which the Russians are searching for petroleum, for this paper refers to such far-flung areas as the Arctic Tamir Peninsula, Kamchatka and Sakhalin on the Pacific, Lake Baikal in Central Siberia, the great new discovery at Neftadag in the plains of West Turkestan, and the oil of the Ferghana oasis, where the derricks look out over to the mosques of Kokand. Of interest also is the new pipe line to supply the industrial centers of Ukraine grouped around the great hydroelectric plant built at Dneprotroy on the falls of the Dnieper. The technical achievements have been noteworthy and we must pause to consider the scope of the undertakings being carried forward. Russia is at the worst a good second to the United States in petroleum reserves and for a long time to come will be a most important factor in the petroleum markets of the world. Her story should be of interest to everyone in the industry. The First Five Year Plan The first Five Year Plan, covering the period 1928-29 to 1932, accomplished the task of transforming the Union of Soviet Socialist Republics from an agricultural, backward land into a powerful independent industrial country, with an advanced technological foundation of its own for finally achieving the social reconstruction of the entire national economy. Along with the gigantic forward 'strides in industry and transportation, radical changes took place in agriculture. The creation of more than 5000 great state farms and of more than 200,000 collective farms serviced by a widespread network of machine-tractor stations has brought the U.S.S.R. to the fore as the largest agricultural country in the world. Imports of tractors and other agricultural machinery in the initial years of the Five Year Plan and the intensive output of this equipment by the great plants of the U.S.S.R. in the latter years of the plan have brought about the mechanization of agriculture in the Soviet Union. This year 250,000 tractors and 30,000 combines will operate in the fields

Jan 1, 1934

By J. B. Hiskey

The hydrometallurgical application of thiourea in processing precious metal ores and concentrates has reached the development stage. This paper reviews recent technical literature covering the process development of thiourea leaching. In addition, recent fundamental contributions are discussed. Most of the interest in thiourea leaching has involved treating high grade concentrates that have sufficient value to just the use of thiourea as a reagent. An important development in thiourea technology is the addition of SO2 to the leaching solution. This procedure effectively reduces the decomposition of thiourea and eliminates the problems of passive surface layers that limit the leaching efficiency. Results for the thiourea leaching of a bulk sulfide concentrate and a residue from the autoclave leaching of a smelter flue dust are also reported. As determined by a standard bottle roll cyanidation test, the bulk concentrate was extremely resistive to cyanide leaching yielding only 16% gold and 2% silver extraction in 24 hours. Leaching with a relatively concentrated thiourea solution (1MCS (NH2)2) resulted in 83% gold and 75% silver extraction in four hours. With the treated flue dust residue, gold extraction was about 60%. Gold and silver extraction with cyanide was sensitive to both cyanide concentration and oxidizing conditions. Cyanidation resulted in 59% gold extraction and 77% silver extraction in 24 hours.

Jan 1, 1985

By H. R. Wuthrich

The Metallgesellschaft AG decided in late 1965 to build an Electrolytic Zinc Plant at Datteln (W. Germany). Lurgi-Chemie was entrusted with the engineering and erection of the entire plant. Ground was broken in February 1967 and the operation was started on August 1st, 1968. The new Electrolytic Zinc Plant was designed to produce a minimum of 100,000 metric tons of special high grade zinc and 200,000 metric tons of sulphuric acid. Concentrates from Meggen (W. Germany) and mainly Timmins (Canada) are roasted in two turbulent layer roasters. The sulfur dioxide containing gases are converted in a "Bayer double catalysis unit" to sulfuric acid. The calcine is leached batch wise, the leach residue separated from the pregnant solution by counter-current thickeners and drum filters. For maintaining the sulfate balance a modified jarosite leach is being used. After a two step purification the neutral solution is mixed with spent electrolyte and cooled in unpacked atmospheric cooling towers. Three electrical circuits are supplying the power to the tankhouse, each rated at 30,000 amperes. With a maximum current density of 750 amperes per square meter and a stripping cycle of 24 hours, an average current efficiency of 90 percent is obtained. Cathodes are melted in one induction furnace and cast into shapes, or alloyed with aluminum and copper for die-cast metal.

Jan 1, 1970

By W. C. Knopf, G. Samsel

For several years International Minerals & Chem-ical Corp. has used a radiation method to assay potassium content of products from potash and feldspar beneficiation. The procedure is rapid, accurate, and inexpensive and is easily handled, if necessary, by nontechnical personnel. Data are presented to show the accuracies that may be expected if the technique is used for control of pilot plants or large-scale plants. Natural potassium is composed of three isotopes —K, K and K. Five other isotopes, artificially produced, have been detected. In natural potassium only the K isotope, with a half life of 1.4x10 years, is radioactive. Its modes of decay are beta and gamma rays, positrons, and x-rays. Only the more abundant beta rays, however, are important in radiation measurements using geiger tubes. Barnes and Salley' measured radiation of potassium salts in solution in 1943. Gaudin and Parnell2 first reported the use of solid salts arranged in a vessel surrounding the ß counter in 1948. Later, Scheel used the method to assay potassium content of various crude and finished potash salts. Experimental: Dip-type Geiger-Muller tubes (TGC-5) supplied by Tracerlab Co. were used in all radiation counting measurements. The tube was encompassed by a glass container about M in. larger in diameter than the tube. This container, which served as a sample holder, was closed at the bottom with a rubber stopper to facilitate removing the samples. Samples were not weighed, but about 40 g of sample were needed for each test. Electrical impulses from the tube were counted on either a Tracerlab scaler or a rate meter. To obviate the need for constant attendance, preset features were incorporated into the scalers, so that at a predetermined time or count the units were automatically deactivated. When rate meters were used, counting rates were read directly from instrument or from a recorder used in conjunction with the rate meter. Each tube was calibrated, according to the manufacturer's instructions, to determine the correct operating voltage to insure reproducible results. A linear calibration plot of percent K2O vs counting rate was also obtained for each tube by recording the counting rate plus background count of several standards of different K2O content chemically analyzed by the chloroplatinate method.' These standards were of approximately the same particle size distribution as samples to be assayed. Specific background count caused by cosmic rays and other surrounding radiation was checked periodically by counting a sample of pure NaCl. Fig. 1 is a representative calibration plot. Assays were determined directly from the standard plot or calculated by subtracting the background count from the counting rate, then multiplying by the slope of the line. Chemical assays of the test samples were made by the Sherril method," a flame photometric technique, or the chloroplatinate method. Data: The radiation assay method has been used for three years by International Minerals & Chemical Corp. in the laboratory and in pilot plants processing ores containing potassium. These dry concentration plants process sylvinite and langbeinite ores at Carlsbad, N. M., and feldspar ores at Top-sham, Maine. Sylvinite ore is predominantly a mixture of syl-vite (impure KCl) and halite (impure NaCl). Contaminants include sulfates, such as langbeinite (2MgSO - K2SO4), kieserite (MgSO H2O), poly-halite (MgSO4.K2SO, 2CaSO, . 2H2O), and slimes. Langbeinite ore is predominantly langbeinite and halite with small amounts of sylvite, sulfates other than langbeinite, and slimes. Several variables, in addition to correct calibration and standardization of tubes, were found to be important in obtaining reproducible results. Particle size distribution of standard samples should be

Jan 1, 1959

By Will Mitchell, T. G. Kirkland, C. L. Sollenberger

R. S. Handy (Santa Rosa, Calif.)—It would be interesting to learn the comparative results of treating the Korean scheelite ore described in this paper according to the following procedure: I—Follow the procedure described in the paper to the recovery of the sulphides by flotation. 2—Dilute the residue from the sulphide flotation strongly with water and disperse the contained colloids by adding a mixture of 75 pct sodium silicate and 25 pct quebracho to dispersion point. 3— Settle the dispersed pulp and decant the supernatant colloids. 4—-Dilute, settle, and decant the pulp until the settled residue is crystalline. Not over 10 pct of the tungsten minerals should follow the colloids. 5—Treat the settled residue by flotation, having established the proper pH. Oleic acid homogenized with cresylic acid or kerosene is more selective for scheelite than is oleic acid alone. (The recovery of the contained tungsten minerals should be practically complete in this operation.) 6—Deflocculate the tungsten concentrate from step 5 with the same dispersion agents as in step 2 and treat the deflocculated pulp by gravity. The minerals that tend to float with scheelite are generally of low specific gravity and the separation is efficient. The heavier contaminants, such as pyrrhotite and magnetite can be removed magnetically, leaving a practically pure scheelite. E. J. Pryor (Imperial College of Science and Technology, London)—It occurred to me that instead of using temperature as a differentiating control, more precision might be obtained with a reagent of a type we developed here for the flotation of high grade fluorspar in cold pulps. This reagent, which is manufactured on a modest scale in England, is based on oleic acid, which has been modified by our patented process to ensure complete stable dispersion at any desired concentration in water. It thus becomes possible to utilise unimolecular layers with good selectivity. In the fluorspar flotation for which we developed it, it is possible to hold a tight control on depressing quebracho for the calcite without substantial loss of flu-orite, and recovery exceeding 99 pct is not uncommon in the mill where it is in use, even under wintry conditions. No attempt has been made yet to extend the use of the reagent, as we have not completely overcome

Jan 1, 1952

By H. S. Thomsen, W. C. Duesterhoeft, R. E. Hartline

The attenuation and phase shift which formations produce in the electromagnetic field of an induction-type electrical well-logging instrument are great enough to substantially affect the response of the tool to formation conductivity under normal logging conditions. The application of the general equations for the propagation of an electromagnetic field in a conductive medium to the transmitter-receiver coil pair of an induction-logging-tool coil system gives an expression for the response which properly takes the propagation effects into account. A comparison of a calculation of this type with the response computed from the commonly used geometric factor concept, which does not include the propagation effect, leads to a factor Go representing the ratio of the responses computed by the two methods. The value of Go decreases not only with increasing formation conductivity, but also with increasing transmitter-to-detector coil spacing. For a single coil pair with a 40-in. spacing, the value of Go is 0.972 in a 20-millimho/m formation. The value is reduced to 0.915 and 0.812 for conductivities of 200 and 1,000 millimhos/m. As a result, the basic signal generated by the induction-logging coil system is not linearly related to formation conductivity as expected from the geometric factor concept. A uniform conductivity scale can be obtained only by adding a suitable nonlinear element to the recording system. The addition of auxiliary coils, having spacings less than the main-coil span, to achieve focusing results in an even greater departure of the basic signal from linearity with conductivity. The solution of the field equations near the interface between two formations of different conductivity gives the curve shape on an induction logging tool in crossing the interface. The addition of auxiliary coils to achieve focusing can add anomalous character to the curve shape in crossing the interface, which might be mistaken for lithological detail. Preliminary calculations which include the propagation effects in the determination of the conductivity correction for thin beds lead to correction factors which are substantially smaller than those obtained from geometric factor considerations. It is apparent that thin-bed corrections derived from geometric factor calculations are of doubtful validity. INTRODUCTION Although the electromagnetic induction type of electrical well log has been used for a number of years and has gained general acceptance in quantitative well-log interpretation, no technically complete investigation of the mechanism and of its operation has been published. The studies which have been presented are based upon the premise that neither the shape nor the intensity of the induction field of the logging tool is in any way affected by the electrical characteristics of the formation. From the inception of induction logging it has been recognized that under some formation conditions the performance of the instrument could be expected to be substantially different from that predicted by the simplified analysis. This anomalous performance has been called "skin effect" since it is the result of the same phenomenon which causes high-frequency alternating currents to flow only near the surface of metallic conductors. In the range of conductivities encountered in the sediments, the formation actually does not exhibit the sharply defined conducting "skin" shown by metals. The gradual modification of the distribution of the currents in the formation, produced by the induction field of the logging tool, is the direct result of phenomena associated with the propagation of the electromagnetic field through the formation. Therefore, it can be much more appropriately described as the "propagation effect". One purpose of this paper is to review the results of a solution of the equations for the performance of a single transmitter-receiver coil pair induction-logging system which takes into account the propagation effect, showing the manner in which the tool performance established by this analysis differs from that derived from the less comprehensive analyses currently in use. PRINCIPLE OF OPERATION OF THE INDUCTION LOGGING INSTRUMENT The high-frequency alternating current which is maintained at a constant value in the transmitter coil

By Dever Ashmead

ANTHRACITE was first mined in the Wyoming Valley and sold as an article of commerce in 1808. As some preparation has always been necessary to make it ready to burn, the preparation of anthracite must date back over a hundred years. Two vital factors have determined to a large extent the degree and method of anthracite preparation. These are, first, the character of the beds worked and the methods by which they were mined and, second, the equipment used and practices followed in the burning of the coal. It is not the intention here to go deeply into these phases of preparation as a paper of no mean length could be prepared on the history of either. Rather, the intention here is to point out the main considerations and to show the influence they have exerted on the preparation of anthracite. MINING METHODS AND THEIR RELATION TO PREPARATION In the beginning f the nineteenth century, the coal beds were virgin with the possible exception of some outcroppings that had been worked, to a slight extent, by the Indians. It is known that the American aborigines had a knowledge of the use of this fuel, because when the Wyoming Valley was purchased from them, in 1754, they mentioned the fact that, by selling the land, they would lose their coal.

Jan 9, 1921

By David R. Mitchell, R. B. Hewes

MANY processes for cleaning coal that are in use depend primarily on physical properties of coal and refuse other than specific gravity and surface conditions relating to froth flotation. These properties are' shape, coefficient of sliding friction, resilience, friability, magnetic susceptibility, and electrical conductivity. In many of these processes specific gravity does have some effect and many separators are designed to utilize more than one of the physical properties cited. Although the processes described herein do not have a widespread application, yet for specific coals and specific conditions, they are economically important. A problem confronting many coal-mining districts is the marketing of the slacks or screenings and dust passing the final sizing screens. Proc¬esses in commercial use installed primarily to increase the form value, and hence the market value, of these slacks and dusts include briquetting, packaging, and low-temperature carborization. MECHANICAL PICKERS Machines utilizing shape, frictional resistance, and differences in resilience of coal and impurities are usually called mechanical pickers. They require a closely sized feed, therefore their use is confined to the pea, nut, and egg sizes. Various types of these devices are described by Berrisford, 1. 2 Taggart, and Yeele.

Jan 1, 1943

By B. E. Warren

Jan 1, 1965

By A. Taylor

NICKEL-RICH alloys hardened with small additions of titanium and aluminum and centered around that region of face-centered-cubic primary solid solution, 7, where the atomic ratio of nickel chromium is about 3 to 1, form an important series of high temperature materials because of their resistance to oxidation, high temperature strength, and excellent creep characteristics at elevated temperatures.' With suitable heat treatment it is possible to precipitate a phase based on the ordered face-centered-cubic y' phase, Ni,,Al, from the randomly ordered nickel-rich y face-centered-cubic primary solid solution. By adjusting the ratio of aluminum to titanium the precipitation of needles of the hexagonal intermetallic compound n-NiaTi may be effected. In the present investigation, the main interest was focused on the interrelationships among the y, y, and 7 phases. By using alloying elements of high purity and a suitable melting technique the presence of carbides and nitrides could be completely obviated, although it is realized that their presence is probably essential in alloys of commercial importance. As a preliminary to the study of the Ni-Cr-Ti-A1 system, it was necessary to establish the constitutional diagrams of the three contiguous systems, Ni-Cr-Al, Ni-Ti-Al, and Ni-Cr-Ti, which together form the nickel-rich corner of the Ni-Cr-Ti-A1 quaternary tetrahedron. Accounts of this work on the ternary systems have already been published by the author. A preliminary disclosure of the author's investigations on the ternary and quaternary systems has been made by Hignett2 and has since stimulated work in the same field by Nordheim and Grant." Before the detailed account of the quaternary system, a brief description will be given of the three contiguous ternary diagrams on which it is ultimately founded. Ni-Cr-Ti System The 750° and 1000°C temperature isothermals of the Ni-Cr-Ti system as determined by Taylor and Floyd' are shown in Figs. 1 and 2. The single phase fields of greatest interest are occupied by the extensive face-centered-cubic y primary solid solution of chromium and titanium in nickel, and the close-packed-hexagonal Daltonide, n-Ni3Ti, from which tie-lines radiate across the very wide y+n two-phase field. The chromium-rich primary solid solution is represented by a. As may be seen from the diagrams, the extent of the y phase field increases quite appreciably as the temperature is raised from 750" to 1000°C. Isoparametric lines for the y phase are shown in Fig. 1. They are interesting in that they are almost parallel to the y/r+n boundary. Thus the determination of the tie-line directions is entirely dependent on the exact stoichiometry of composition of the 7 phase. Ni-Ti-Al System The 750°C isothermal section of the nickel-rich portion of the system Ni-Ti-A1 as determined by Taylor and Floyd is shown in Fig. 3.' The regions of greatest interest are the extensive y primary solid solution of titanium and aluminum in nickel, the y' Berthollide phase field based on the ordered face-centered-cubic structure of Ni3Al, and the hexagonal Daltonide phase, n-Ni3Ti. As may be seen from Figs. 3 and 4 the area occupied by the y phase is substantially the same at 750°C as at 1000°C, but the area of the 7 phase is considerably greater at the higher temperature. The tie-lines radiate from n-Ni3Ti across the y+v and y' + v two-phase fields and are evenly distributed

Jan 1, 1957

By Edgar Stansfield

ONE of the most striking features of the coal series passing from peat through brown coal, lignite, etc., up to anthracite is the gradual reduction of moisture content with the increased coalification of the original plant material. Thus drained peat from a bog may contain 90 per cent water, brown coal contain 50 per cent, lignite 30 per cent, while a bituminous coal may contain only 1 per cent moisture. Moisture, therefore, is one of the important factors to be considered in coal classification, especially with the lower rank coals. With bituminous and higher rank coals the moisture content is less satisfactory for classification; it may even pass a minimum value and then increase with increasing rank to anthracite and superanthracite. Coal in an undisturbed seam contains moisture which is an integral part of the coal, but it may also be wet with free, underground water percolating through the seam. Only the former must be considered in evaluating the moisture content of the coal for classification purposes; this will be called the "true moisture" of the coal. When the seam is mined and sampled the sample taken may show the true moisture; on the contrary, it may contain in addition free mine water or, especially in dry, well ventilated mines, it may contain less than the true moisture. Coal contains unstable organic compounds which may decompose, with the production of moisture, when the coal is exposed to air at ordinary temperatures, or is heated with or without exposure to air. The potential moisture of a coal therefore is higher than its actual moisture. The lower the rank of the coal, the greater its instability, as a rule, and the greater the care necessary to avoid oxidation or decomposition in any investigation of moisture content. The majority of coal workers have preferred, on account of the difficulty in evaluating the true moisture of a coal, and for other reasons, to classify coals by analyses calculated to the dry-coal basis. A number of workers familiar with lower rank coals have recently insisted that the classification of such coals can be satisfactory only if analyses on the moist-coal basis are employed. The moisture-holding capacity of coal is therefore intimately connected with coal classification, and in this paper a procedure is outlined for determining the true moisture of a coal.

Jan 1, 1932