Search Documents

By David H. Browne

The use of coal-dust fired reverberatory furnaces, or indeed of rever-beratory furnaces of any description, was for the Canadian Copper Co. a matter of necessity, and not of choice. For 20 years smelting had been done in blast furnaces alone, and with the Herreshoff furnaces used prior to 1904 there was no trouble in treating fine ores. But little flue dust was produced, and this, following the time-honored custom, was wetted down and put back with the charge. Whether the flue dust really smelted, or whether it was worn out by being chased around in a circle, was a problem that troubled no one. With the installation of modern blast furnaces and high-pressure blowing engines, in 1904, flue dust commenced to assert itself. Evidently more dust was made than could be smelted, but so many vital. problems engaged our attention at that time that this minor question was pushed to one side. In 1906, the details of blast-furnace smelting and the conversion of matte had been worked out to a satisfactory conclusion, and the ever-increasing piles of flue dust and fine ore on the stock yard demanded serious consideration. Numerous experiments in sintering, briquetting, mixing with converter slag, forming blocks of flue dust with green-ore fines and cement, and so on, were undertaken. None of these showed much promise. Our problem was still further complicated by the question of treating converter slag. The ore was basic, the slag was not needed as a furnace flux, and it was felt that under these conditions the old method of pouring slag in molds and resmelting in the blast furnace was an unnecessary expense. If the converter slag could be settled in basic-lined reverberatory furnaces, in which at the same time flue dust and green-ore fines could be smelted, two problems might thus be solved. Reverberatory practice with our ores was, however, an unknown factor. As carried on in the West, on siliceous ores and concentrates, at least 25 per cent. of fuel was required, and even this ratio depended greatly

Jan 1, 1915

By T. Glen Heslop, Dennis H. Laubscher

INTRODUCTION In all cave mining operations waste is drawn mixed in the ore, hauled, hoisted and milled. This waste usually contains some mineral which partly covers some of the costs of mining and milling it, but it still re- presents a loss of profits as the production rate from the mine is matched to the mill capacity - every tonne of waste milled replaces a tonne of profitable ore. Draw control aims to reduce the amount of waste drawn and to increase the amount of ore recovered. It is also used to regulate the grade of ore flowing to the mill and in block cave blocks to prevent potential stress build- up on the major apexes above grizzly drifts. This paper summarises what has been learnt about draw control in the forty years that cave mining methods have been used in the three largest underground chrysotile asbestos mines in the southern hemisphere. The four mining methods to which draw control has been applied are: a. Block caving. b. Shrinkage with overburden caving. c. Sublevel caving. d. Open stoping. Open stoping has been included because on a number of occasions severe falls from the back and side of these open stopes have occurred. Without full records of where and when ore is blasted, when and how much ore has been drawn from each of the drawpoints, it would be impossible to analyse the migration of ore and fallen waste in the stope. Several problems peculiar to chrysotile asbestos ore bodies affect the practice of draw control. Heterogeneous fragmentation, cavities, side pressures and the interaction of stresses in the caved ore affect the migration of ore under draw. Fibre is normally not developed uniformly throughout the ore bodies, values vary from place to place but there is usually a general decrease upwards and the hangingwall contact is an economic limit. The immediate hangingwall rock frequently looks like the ore body hostrock and is difficult to recognise in a drawpoint, and cannot be used as the marker for stopping draw. During caving or shrinkage, a large proportion of fibre becomes detached from the host rock and re- ports in the fines, which migrate differently to the larger rocks. The fines are not sticky, and flow easily if loose and dry, but compacted, the fibre and rock fines con- solidate the ore. During draw the proportion of fines in the ore varies considerably, as fines either flow relatively freely between the large rocks or become trapped and compacted above large rocks or hangups. This creates a large sampling error in drawpoint grade assessments, whether done visually or by bulk sampling, unless the assessments are done frequently. The method of draw control used is to regulate the draw rate in an attempt to lower the ore-waste interface as evenly as possible, and to finally stop working the drawpoint when a calculated tonnage has been drawn.

Jan 1, 1981

By Vincent P. Gianella

THE most intense earthquake on the Pacific coast in the last several years, and probably the second most intense shock to occur in Nevada since it was settled, was felt in many Western States shortly after 10 p.m. on Dec. 20, 1932. Be- cause the rifted area contered about the northern end of Cedar Mountain it is referred to as the Cedar Mountain, Nevada, earthquake. An idea of the intensity of the shock may be gathered from the distance at which it was felt: in Wyoming, Utah, Idaho, Nevada, Washing- ton, Oregon, California and Arizona. It is the strongest quake centering in Nevada since the Pleasant Valley earthquake on Oct. 2, 1915. Despite the strength of the vibrations and the large area over which they were felt, relatively little damage was done. The extent of the damage consisted of a few old stone buildings demolished as shown in Fig. 1, much cracked and fallen plaster, many chimneys shaken down and considerable cracking of brick walls. There were no deaths and four people were but slightly injured. The small amount of damage was due, largely, to the scarcity of structures within the area of strong vibrations, but an important factor was the aridity of the region (see Fig. 2) and the shallowness of soil cover so that there was but little water-saturated loose material in which strong secondary vibrations could be formed. Had this earthquake occurred in a region of heavy precipitation and dense population the damage to property and loss of life would undoubtedly have been large, with consequently much more newspaper publicity.

Jan 1, 1933

By L. R. Woodyatt, H. J. Beattie, C. T. Sims

Theories correlating the formation of u and related intermetallic compounds to the electron-per-atom density of binary and ternary alloys have appeared regularly in recent technical literature. These same principles can be modified and applied to complex precipitation-strengthened alloys such as the iron-, cobalt-, and nickel-base superalloys and the stainless steels. Since these complex alloys contain carbides and other phases that normally precipitate before the U-type phases, the nature and amount of the precipitated phases must be calculated first. The following general formula is then applied to the residual matrix composition of the alloy: element. The magnitude of the resulting number is indicative of whether the alloy will form a a -type phase. When these calculations (which are computerized) are systematically applied to alloys of knoun phase analysis, a breakoff in average electron-vacancy number is noted between U-free and U-prone alloys. Alloys with an average electron-vacancy number higher than the breakoff form a-type phases, while those with lower ones do not form these phases. This method could then be used to eliminate from consideration all experimental compositions that would precipitate undesirable phases. It also is useful in evaluating analyzed heats of alloys where minor heat-to-heat variations determine whether the alloy is o-free or o-prone. THE highly significant development of strong, ductile superalloys to provide reliable construction materials in the 1000" to 2500° F temperature range has been due principally to unremitting application of Edisonian techniques and logic by the dedicated physical metallurgists who have shouldered this responsibility. Tools such as the electron microscope, phase analysis, and computers to accomplish regression analyses have been used heavily, but the effort has been essentially practice of an art, rather than a science. The objective of this paper is to describe and illustrate application of some relatively fundamental principles to certain of these alloy systems in an attempt to remove some of the empiricism from the technology. Specifically, the work presented here deals with the use of periodic-group relationships to predict the formation of intermetallic phases which can occur in primarily austenitic (fcc) structures. Calculations that have been developed might be applied in the design of new alloys and the evaluation of known alloys, and thus have the potential of eliminating vast areas of unnecessary alloy preparation and evaluation. ALLOYING CONCEPTS AND STRUCTURAL FEATURES OF SUPERALLOYS Strength is produced in austenitic superalloys by three principle mechanisms: 1) precipitation of y'; 2) formation of carbides; 3) solid-solution hardening by soluble refractory metals. The first mechanism requires the addition of aluminum and titanium, the second requires carbon and carbide-forming elements, while the third calls for the addition of molybdenum and/or tungsten. A considerable concentration of chromium is usually maintained to resist oxidation/corrosion, but it is also an important carbide-forming element. Fig. 1 shows a sketch and electron micrograph of the structure of a typical wrought nickel-base super-

Jan 1, 1967

J. L. McK. YARDLEY,* Pittsburgh, Pa. (written dlscussion ?) .-It is interesting to observe how closely Mr. Hansen agrees with other investigators to the effect that the art of electrolytic zinc has left the realm of mystery. In his introduction, lie has said practically what Thomas French said in his paper "The Future of Electrolytic Zinc. "1 The successful electrolysis of zinc from sulphate solutions has not been an easy matter, and it is only within recent years that the difficult problem of depositing high-grade zinc has been satisfactorily: accomplished on a commercial basis. The principal requisite is. that the electrolyte shall be quite free from certain impurities. The methods by which freedom from these impurities is assured are now very well understood, and with experienced superintendents there is little difficulty in obtaining a high efficiency in that part of the process. When certain underlying principles are recognized, the difficulty encountered in dealing with the filtration of the acid and slimy solutions also largely disappears, although it has been a very serious one to the uninitiated. In the dissolving of the zinc from the roasted ore, there is nothing which any competent chemical' engineer cannot undertake, and any other operations connected with the electrolytic process are either of little or no difficulty, or are common to the retort process. Mr. Hansen also agrees with R. G. Hall's statement in " Some Economic Factors in the Production of Electrolytic Zinc:"2

Jan 10, 1918

By A. W. D. Hills, M. R. Moore

An apparatus has been developed in which metals can bc solidified under closely controlled unidirectional heat flow conditions. The metals are cooled by a multiple-air jet system, designed so that the heat transfer coefficient is uniformly distributed over the cooled surface. They are contained in a special furnace system of low thermal mass which enables unidirectional heat flow conditions to be rigorously maintained for certain specific cooling rates. This apparatus has been used to study the solidijication of pure lead and pure tin at zero superheat, solid metal thicknesses being determined by thermal analysis, and by dipstick readings. Detailed thermal balances have been drawn up on the experiments in order to determzne the cooling conditions that most rigorously correspond to unidirectional heat flow. Solid metal thicknesses, measured experimentally for these conditions, have beetz shown to agree closely with the theoretical wedictzons of different integml-profile methods. lt is concluded that any errors inherent in the integval-profile method are no greater than the errors inherent in experimental investigations of solidification. A knowledge of the influence of heat transfer rates on the solidification of metals is essential to the understanding and control of industrial casting processes. Since very few formal methods are available for solving the heat conduction equation under solidification conditions several authors have developed approximate techniques for doing so. One of the most promising is the integral-profile technique that has been used by Goodman,1 Hills,2,3 Tien4 and Hills and ~oore' to predict solidification rates under certain specific heat transfer coniditions. In the first of this present series of papers6 Hills has further generalized the method and developed a universal integral-profile technique that can be used to predict solidification rates under a wide variety of unidirectional heat flow conditions. Since the method is approximate it is necessary to investigate the accuracy with which it predicts actual solidification rates. A review of the literature7 shows that solidification rates have seldom been measured under accurately known heat transfer conditions and it was therefore decided to develop experimental techniques that would enable this to be done. Results obtained would then be available as a check on the approximate solutions already developed, and in the development of further solutions that would be applicable under more complicated conditions. The initial work in this experimental program which is described here, is concerned with the solidification of pure metals at zero superheat under unidirectional heat flow conditions. Subsequent experiments have been concerned with the solidification of pure metals at appreciable superheats, under varying unidirectional heat flow conditions and under two dimensional heat flow conditions. In a series of experiments recently initiated, the solidification of binary alloys is also being investigated. The results of these subsequent experiments, together with relevant theory, will be described in later papers. The solidifying metal has been cooled in all the experiments, by a multiple air jet system designed so that the heat transfer coefficient to the cooled surface is constant and is uniformly distributed over the surface. This type of system has been chosen since only one parameter is needed to specify the heat transfer conditions and since these conditions are analogous to those met in certain continuous casting processes.' Air cooling was chosen in preference to water cooling, however, since it offers a wider range of heat transfer conditions, and since it can be investigated by analogous mass transfer techniques. The first part of this paper discusses the existing integral-profile solutions that correspond to the heat transfer conditions used in the experiments, and describes the development and use of the experimental apparatus. In subsequent sections the heat transfer and solidification results are presented, and the various theoretical predictions are compared with them, and with one another.

Jan 1, 1970

By J. D. Mote, J. E. Dorn

This investigation was undertaken to study the effects of piledup arrays of dislocations on inducing slip, twinning, and fracturing in magnesium bicrystals. A series of variously oriented bicrystals of magnesium having a vertical grain boundary were prepared and tested in tension. It was found that piled-up arrays of dislocations at the grain boundary could, under appropriate conditions, induce slip, twinning- and cracking. The results that were obtained substantiate, at least qualitatively, the general dislocation mechanism for transmission of strain across grain boundaries and the Petch-Stroh concept of fracturing. WHEREAS single crystals of magnesium generally exhibit extensive deformation, coarse-grained poly-crystalline magnesium at subatmospheric temperatures fractures after a few percent elongation.' Although a small amount of ductility is obtained, several features of this fracturing are characteristic of typical brittle behavior. Over a rather broad temperature range the fracture stress is insensitive to the test temperature and the fracture stress increases linearly with the reciprocal of the square root of the mean grain diameter. The course of fracturing is predominantly intergranular, but small fragments of adjacent grains frequently adhere to the fractured surface.2 The brittle behavior of polycrystalline magnesium is attributable to the limited number of facile deformation mechanisms it exhibits at low temperatures. For a general deformation of a randomly oriented polycrystalline aggregate, each grain must exhibit at least five independent mechanisms of deformation to permit accommodation of the imposed deformation from grain to grain.= Although minor amounts of prismatic slip occur in corners of grains where stress concentrations are known to be high, glide in polycrystalline magnesium at low temperatures takes place almost exclusively by basal slip.' The common type of twinning, which takes place on the (1012) pyramidal planes, can under the most favorable orientations, lead to a. strain of only 6.9 pet; the contribution of twinning to the tensile strain would indeed be much less than this in a randomly oriented polycrystalline aggregate of magnesium. Since the three mechanisms of basal slip are coplanar, they are equivalent to only two independent mechanisms, a number insufficient for a general deformation. Consequently, once the permissible twinning has taken place in conjunction with basal slip, no further plastic deformation is possible because of interference to slip at the boundaries of dissimilarly oriented grains. At this stage brittle fracturing takes place due to high stress concentrations at the juncture of slip bands with the grain boundaries; the predominance of intergranular fracturing in magnesium, in preference to transcrystalline fracturing which is prevalent in zinc, has not yet been rationalized. A more atomistic description of the plastic behavior and fracture characteristics of magnesium follows from the analyses made by stroh4 on the stresses induced by piledup arrays of dislocations. Slip first takes place by dislocation motion in the most favorably oriented grains. As the dislocations approach the boundary of a dissimilarly oriented adjacent grain they begin to form an array of dislocations with its attendant stress field. Piledup arrays of screw and edge dislocations introduce high localized shear stresses at the spur of the array; piledup arrays of edge dislocations also induce high tensile stresses localized in the vicinity of the grain boundary. Whereas the shear stresses can induce slip to take place, the tensile stresses, if sufficiently high, can cause fracturing. The localized shear stress will be relieved if sufficient numbers of mechanisms of deformation become operative in the original and the adjacent grain to permit accommodation of the dislocations in the grain boundary. In this event a ductile behavior will be obtained. But if the number of deformation mechanisms is insufficient for complete migration of dislocation arrays into the grain boundary, the tensile stresses due to the edge components of piledup dislocation arrays will continue to increase with increasing applied stress until fracturing takes place. Whereas face-centered-cubic metals have a sufficient number of mechanisms of slip for accommodation of dislocations in their grain boundaries to exhibit ductile behavior, hexagonal-close-packed metals, in general, do not. Consequently, hexagonal-close-packed metals are usually brittle except when conditions such as alloying or temperature permit facile slip by a number of mechanisms. The arguments presented above suggest that the mechanical behavior of magnesium depends on whether or not dislocation arrays in adjacent grains can enter the grain boundary. When such accommodation is possible, ductile behavior is expected; but when such accommodation is impossible, fracturing will ensue. To further test the validity of these arguments it was considered advisable to study the

Jan 1, 1961

By Edward Keller

Under the title, Labor-Saving Appliances in the Works-Laboratory, I published a paper1 in which mas described how multi-manipulations in a works-laboratory and in the furnace-room of an assay-laboratory, can be condensed into single manipulations by applying the proper mechanical devices. For example, I now deposit ill, or withdraw from, a muffle a set of 48 cupels as one unit. The front row (8) of these are blanks or heaters; the other 40, when they have attained the proper temperature in the muffle, are charged simultaneously with the 40 lead-buttons. Three manipulations here accomplish an operation which by the generally customary method requires 136, and this number is only limited by the size of muffle and cnpels. This operation is an enlargement of what I have already described in my former paper, and Fig. 1 shows the improved implements. In the paper referred to I described a gold-silver bead parting-bath, which is the last of the devices used in regular sequence in practice. This bath mas designated as being convenient, but mas not a labor-saver properly. Fig. 2 of the present paper shows a new device. Instead of the original tray, there are now sectional holders for the test-tubes, each having a wooden handle on either end, so that the holders ma?-be removed from the boiling bath, and the acid or water poured oE from each set of tubes (in this case, 7) without waiting to cool. The tubes, held in place by clutches, as shown in Pig. 3, rest in holes in the base-strip, having a smaller diameter than the tubes. Each holder is stamped at either end with a number, so that the bath becomes further useful by permitting several men to use it at the same time without interference. Apart from the handles, the holders are made of sheet-copper.

Jan 1, 1911

By Robert E. Green, Edmund G. Henneke

Expressions are derived for the orientation factors associated with dislocation damping due to dislocation motion in the basal slip plane. The results of the calculation of these factors for zinc crystals aye pvesepzted and the relevance of these results to ultvasonic-attenuation measuvements is discussed. In this paper expressions are derived for the orientation factors associated with damping of sound waves due to dislocation motion in the basal slip plane of hexagonal crystals. For zinc crystals, the orientation factors for dislocation motion in one slip direction only, as well as for simultaneous motion in all three basal slip directions, have been calculated at 1-deg intervals. The results of these calculations are presented in the form of contour diagrams in a sector of a standard polar coordinate graph. The calculations have been carried out for both the traveling- and the standing-wave conditions. The relevance of these results to ultra sonic-attenuation measurements is discussed. Associated with the calculation of the orientation factors, the modes of elastic-wave calculation were also evaluated, according to the procedure previously employed by Hinton and Green.' The results of these calculations are not presented here since similar results have been reported earlier by Mus-grave.2 However, it should be mentioned that, although the qualitative features of Musgrave's results are preserved, the quantitative values are somewhat altered since different values for the elastic constants of zinc were used. ORIENTATION FACTORS It is convenient to refer to three different sets of coordinate axes, Fig. 1, in the following calculations. First, there are the Miller-Bravais axes which are used in describing the Miller-Bravais indices of planes and directions in a hexagonal crystal. These axes are denoted in the conventional manner by a,, a,, a,, and c. The second set of axes used is a rectangular Cartesian coordinate system located as shown in Fig. 1. Note that the x axis coincides with the close-packed direction al [2110], the z axis coincides with the c axis [0001], and the y axis is orthogonal to these two lying in the [0110 ] direction. Finally, a form of Eulerian angles is used to locate the position of the specimen axis. The angle between the specimen axis and the c axis is denoted by 0 and the angle between the projection of the specimen axis on the basal plane and the a, direction is denoted by ø. The majority of observations on plastic deformation of metal crystals indicates that such deformation is caused by the motion of dislocations on a limited number of crystalline planes and in a close-packed direction. In crystals with hexagonal symmetry the most prominent slip plane is the basal plane (0001) and the slip directiops- are one of the close-packed directions, [2110], [ 12101, or [ 1120]. To properly set the stage for the following work, several points must be clarified. First, we want to consider the contribution to the attenuation of elastic waves by dislocations only. While the Granato-Lucke, model for dislocation damping is presently the one most quoted, it is not necessary to refer the present work to it. The only assumption that need be made is that the motion of dislocations absorbs energy from the elastic wave and therefore attenuates it. It is immaterial here how this energy absorption occurs. However, because dislocations have been observed to move most freely on the (0001) plane for hexagonal crystals undergoing plastic deformation, it will be assumed that it is the dislocation motion on this plane which attributes to the observed attenuation. The basic orientation factor, Ok, is essentially the same as that used by Green and Hinton for fee crystals,4 defined by the equation

Jan 1, 1968

By William E. Ford, Edward Salisbury Dana

1. THE SCIENCE OF MINERALOGY treats of those inorganic species called minerals, which together in rock masses or in isolated form make up the material of the crust of the earth, and of other bodies in the universe so far as it is possible to study them in the form of meteorites. 2. Definition of a Mineral. - A Mineral is a body produced by the proc¬esses of inorganic nature, having a definite chemical composition and, if formed under favorable conditions, a certain characteristic molecular structure which is exhibited in its crystalline form and other physical properties. This definition calls for some further explanation. First of all, a mineral must be a homogeneous substance, even when minutely examined by the microscope; further, it must have a definite chemical composition, capable of being expressed by a chemical formula. Thus, much basalt appears to be homogeneous to the eye, but when examined under the microscope . in thin sections it is seen to be made up of different substances, each having characters of its own. Again, obsidian, or volcanic glass, though it may be essentially homogeneous, has not a definite composition corresponding to a specific chemical formula, and is hence classed as a rock, not as a mineral species. Further, several substances, as tachylyte, hyalome¬lane, etc., which at one time passed as minerals, have been relegated to petrology, because it has been shown that they are only local forms of basalt, retaining an apparently homogeneous form due to rapid cooling. Again, a mineral has in all cases a definite molecular structure, unless the conditions of formation have been such as to prevent this, which is rarely true. This molecular structure, as will be shown later, manifests itself in the physical characters and especially in the external crystalline form.

Jan 1, 1922

By J. E. Gruzleski, O. Knacke, M. J. Meixner

The evolution of CO from small specimens of solidifying steel was investigated using a thermobalance technique. Gas evolution begins in the temperature range between 1400" to .1450°C. This behavior is independent of the initial carbon content and the cooling rate. At a constant temperature above 1220°C, the rate of gas evolution is temperature independent. Out-gassing of the specimen is thought to proceed through small channels formed by the coalescence of bubbles between dendrites. LIQUID metals have a higher solubility for gas than the solid. During freezing, these gases form bubbles which may either escape or remain trapped in the solid. Recent work1 on the evolution of oxygen from solidifying silver showed that the gas is not liberated until a large fraction of the melt has solidified, and that the gas is evolved in an almost explosive manner. Because of the commercial importance of CO evolution in solidifying steel, a similar investigation was undertaken to study the mechanism of gas liberation in steel. EXPERIMENTAL The thermogravimetric method of Knacke and eixner1 to follow gas evolution by weight changes was employed. Weight differences of 0.1 mg could be reproducibly measured on specimens weighing 2.5 g. These specimens were taken from alloys with varying carbon contents from <0.01 to 0.11 wt pct and <0.01 wt pct of each of silicon, manganese, and aluminum. Specimens contained in 8 mm ID magnesium alumi-nate crucibles were heated to 1550°C under 1 atm of very pure (99.995 pct) CO with a tungsten resistance furnace. The specimen temperature was measured with a Pt-Pt/Rh thermocouple located directly beside the crucible. It is felt that the temperature thus measured was within 5" to 10°C of the specimen temperature since on fusion the weight of the specimen increased due to uptake of CO, and this weight increase was always observed to begin within the temperature range of 1530" to 1540°C. Even after 3 hr there was a small weight increase with time indicating that the molten specimen was not completely saturated with CO. Therefore, complete saturation was not attempted, and all specimens were simply held for 3 hr at 1550°C before cooling. Two types of cooling experiments were performed. One consisted of continuous cooling at linear rates from 5°C to 20°C per min down to 1020°C. The second type of experiment involved continuous cooling at 10°C per min to a predetermined temperature, and then holding the specimen at this temperature for a certain time. During all of these experiments, the sample weight was recorded as a function of time and temperature. OBSERVATIONS Continuous Cooling Experiments. No gas evolution was detected above 1450°C. The initial weight decrease always occurred between 1400" and 1450°C with the average at 1430°C. With further cooling, gas evolution continued to about 1150°C. Between this temperature and 1020°C no further outgassing was observed. This behavior did not seem to depend on the initial carbon content nor on the cooling rate in the range investigated. Typical patterns of gas evolution are shown in Figs. 1 and 2 for different initial carbon levels and cooling rates. The total amount of gas liberated during solidification varied with the rate of cooling. The total weight change on continuous cooling at a rate of 10°C per min

Jan 1, 1970

J. R. Lane (Metals Research Laboratory, Washington)—A new type of deformation called "kinking" has recently been described. Is there any relation between the "rumpling" described in this paper and "kinking?" D. C. Jillson (author&apos;s reply)—Both are manifestations of bending about [210] axis. The difference is one of degree. W. C. Ellis (Bell Telephone Laboratories, New York) —Some observations of deformation in zinc recorded in this paper may be applicable generally to flow in metals. One of these, deformation in torsion without evidence of slip or twinning in the early stages and with startling ease, when the twist is about the hexagonal axis, adds another method of flow to the presently increasing list of mechanisms. This illustrates again that a crystal will utilize any realizable process to flow and relieve stress. The process is not necessarily classical directional slip—& this case, it is rotational slip. The question naturally occurs: Will face-centered cubic metas stressed by twisting about an octahedral axis flow in a similar manner by rotation on an octahedral plane? I would like to ask Dr. Jillson if he has made any experiments or knows of any experiments of this type on face-centered cubic metals? Face-centered cubic metals possibly would behave differently from zinc, since, for one thing, the stacking sequence is different for the two structures. The results of such experiments, however, would be instructive in providing more information about deformation processes. D. C. Jillson—Dr. Roy E. Swift, working in the Hammond Laboratory at Yale, performed a twist test on a single crystal of brass. The work has not been published, and I do not know the crystallographic direction of the axis of the specimen used. Lo-ching Chang (Columbia University, New York)— Observations similar to Figs. 1 and 2 of the paper were obtained by us during the bending and unbending of an orthorhombic Au-Cd alloy.&apos;l This orthorhombic alloy is the product of diffusionless transformation from a single crystal of p Au-Cd alloy (CsC1 structure) containing 47.5 atomic pct Cd on cooling to about 60 "C.62 Referring to the effects of annealing, has the author tried any loilg time high temperature anneal, such as 150 to 200 hr at 40O°C? D. C. Jillson—No. C. Crussard (Ecole des Mines, Paris: France)—I

Jan 1, 1952

By C. L. Kinney

The rapid increase in the amount of steel produced by the basic open-hearth process is an index of its ability to produce high-grade steel from raw materials of the most, varied physical character and chemical analysis. This inherent adaptability of the process has resulted in a lack of care in the selection of raw materials, so that in far too many cases charges are used of a chemical and physical character not justified by local economic conditions. A practice, or series of practices, should be used that will result in the greatest economy for the plant as a whole; therefore, the operations of blast furnace and open hearth must be considered together. In this paper, an effort has been made to show those variations in both open-hearth practice and cost that follow changes in the analysis of the pig iron arid it may be said that the theoretical costs shown are worthy of careful study and consideration. Carbon, manganese, silicon, phosphorus, and sulfur constitute the principal metalloids in basic pig iron and play the leading role in the production of steel by the basic open-hearth process. The percentages of each of these metalloids, with the exception of carbon, is a variable that has its genesis in the economic relation of the blast-furnace plant to its ore and fuel supplies. As the amount of carbon in the iron is a saturation function of the temperature at which it is produced, the variation in the amount carried is, for any given locality and grade of iron, practically negligible and is so considered in the eight heats discussed in this paper. The melting and refining reactions in an open-hearth furnace, either acid or basic, are essentially oxidizing and vary greatly with the type and age of the furnace, as well as the character of the fuel employed. The outstanding characteristic of the basic process, and the one that explains its predominance over the acid, is its ability to form out of the lime charged and the phosphorus oxidized from the charge a stable

Jan 1, 1924

By Frank Rieber

The discovery that strongly magnetic bodies localized near the surface of the earth could be detected by the distortion which they produced in the resultant magnetic field marked the beginning of magnetic surveying methods. From an original ability to detect bodies of magnetic iron ore and the like when located very close to the surface, these methods have been extended until today they promise to give much information with regard to the structure of such slightly magnetic material as sedimentary rock containing only a very small proportion of iron.&apos; The recent extensions have been made possible through the development of more delicate instruments, and of methods for their use. From the original compass and dip needle, the design of apparatus has progressed until equipment is typified by magnetic balances capable of measuring the components of the earth&apos;s field to an extremely high degree of accuracy. It seems unlikely that the limit of such instrumental development has been reached. Just as the change from compass and dip needle has enabled the location of relatively minor changes in magnetic materials, so additional developments in the direction of increased sensitivity, as well as in greater dependability and constancy of operation, should reveal positively many slight changes which either escape notice in the present surveys or are so small that they cannot with certainty be separated from uncontrollable errors due to inconstant operation of the equipment. The ability to read smaller and smaller variations does not mean, of course, that deductions as to the causes of these variations will be made as accurately and definitely as is possible with the more pronounced anomalies.

Jan 1, 1929

By Frank Rieber

THE discovery that strongly magnetic bodies localized near the surface of the earth could be detected by the distortion which they produced in the resultant magnetic field marked the beginning of magnetic surveying methods. From an original ability to detect bodies of magnetic iron ore and the like when located very close to the, surface, these methods have been extended until today they promise to give much information with regard to the structure of such slightly magnetic material as sedimentary rock containing only a very small proportion of iron.1 The recent extensions have been made possible through the development of more delicate instruments, and of methods for their use. From the original compass and dip needle, the design of apparatus has progressed until equipment Is typified by magnetic balances capable of measuring the components of the earth&apos;s field to an extremely high degree of accuracy. It seems unlikely that the limit of such instrumental development has been reached. Just as the change from compass and dip needle has enabled the location of relatively minor changes in magnetic materials, so additional developments in the direction of increased sensitivity, as well as in greater dependability and constancy of operation, should reveal positively many slight changes which either escape notice in the present surveys or are so small that they cannot with certainty be separated from uncontrollable errors due to inconstant operation of the equipment. The ability to read smaller and smaller variations does not mean, of course, that deductions as to the causes of these variations will be made as accurately and definitely as -is possible with the more pronounced anomalies.

Jan 1, 1928

By R. Woodward Moore

A GRAPHICAL method of analyzing the data obtained from shallow earth-resistivity depth tests is presented. The method is based upon empirical results and has no theoretical basis. The usual apparent resistivity-electrode spacing curve is used together with a cumulative resistivity-electrode spacing curve plotted on the same sheet. The greatly reduced scale required for plotting the cumulative values of resistivity together with the effect of the summation of the individual resistivity values serves to minimize the effect of purely local surface anomalies and inadvertent errors of measurement. The point of intersection of tangents or straight lines drawn to intersect at zones of maximum curvature in the cumulative curve indicates the depth to the underlying material. Numerous figures are presented in which data from published reports and from recent field studies are analyzed and the results compared with actual depths established by borings or with depth values obtained by the use of theoretical methods of analysis. Smoothly rounded curves of apparent resistivity such as are often obtained in the field, and which have been a serious drawback to attempts to analyze the data empirically heretofore, appear to be susceptible to rather accurate analysis by the method described. The method is best suited to analyses involving shallow two-layer formations. It has been applied successfully, however, in analyzing the data obtained from tests made over shallow three-layer formations. As with most empirical methods, its chief advantage is its simplicity and ease of application.

Jan 1, 1944

By Mark W. Springett

The sampling of precious metal deposits entails inherent problems due to the low mineral abundances, high mineral specific gravities, skewed grade distributions and wide ranges of mineral particle sizes. Sampling practices and precautions are discussed with particular attention to each of the tripartite stages of sampling - sample acquisition, sample preparation and sample assaying. Practical examples of approaches to the sampling problem are given and some examples of significant sources of error are provided from gold and silver deposits in North America.

Jan 1, 1984

By D. D. Todd, W. A. Oates

THERMODYNAMIC data for solutions are best derived from a combination of equilibrium and calorimetric studies. However, the accurate measurement of heats of mixing of metallic solutions at high temperatures presents considerable experimental difficulties, simple calorimeters1-3 giving

Jan 1, 1964

By Arthur West

IT is the purpose of this paper to describe briefly some recent large power stations for blast furnaces, where the blast is exclusively supplied by gas engines using furnace gas. The stations are given in the chronological order in which they were designed, in order to indicate the various improvements suggested by experience. Fig. 1 shows the blowing-engine station of the Bethlehem Steel Co. at Bethlehem. Although the picture shows only five blowing engines, the house now contains 11 engines. In the diagrammatic. plan the arrow shows the position and direction of camera. This station handles five modern blast furnaces of 450 to 500 tons capacity each. In this, as in all the other stations described in this paper, each furnace is blown by-two single tandem gas engines. Ten engines are thus required for five furnaces, leaving one single tandem spare engine. This spare capacity has been shown by several years&apos; experience at Bethlehem to be adequate to insure continuous operation. The engines in the Bethlehem station are right hand and left hand, arranged in pairs. The outboard bearings of each pair are close together so that there is not room for passageway between them. On the right of the picture are shown the inclined drums communicating with the cold-blast lines outside of building, so that any engine may be operated on any furnace. The illustration shows four cold-blast gate valves with pipes passing through wall, but since the photograph was taken the drums have been extended to take care of a fifth valve for a fifth furnace. At the extreme back of the picture can be seen the tubs of three twin vertical-horizontal Southwark steam blowing engines, which, although of modern design and as good as new, are not operated because of the greatly reduced blowing cost shown by the gas blowing engines.

Jan 6, 1915

It was customary formerly to publish an index of the Transactions about every fifth volume, but since the Institute began in 1913 to publish three volumes instead of one volume per year, this has been deemed impracticable and unnecessary. No collective index has been published since the one covering Volumes I to XXXV inclusive, excepting a short one covering Volumes XXXVI to XL inclusive. The Board of Directors, therefore, upon the recommendation of the Committee on Papers and Publications, decided to publish this index of Volumes XXXVI to LV inclusive, and thus enable members to have in condensed space the collective indexes of all the volumes of the Transactions.

Jan 1, 1918