Search Documents

By T. K. Smith

The comments contained in the discussion of the paper concerning the prediction of fracture gradients are of considerable interest, since the subject is of a very controversial and timely nature. It is regrettable and Fairhurst2 contradicts the author's statement in the third paragraph of Other Applications. These references create significant doubt that Eaton's Eq. 1 predicts fracture pressure during the injection of fluid into old wells. 3. No evidence is presented in this paper to support the author's Conclusions 2 and 3. While an empirical coefficient related to back-calculated field data is correlated with depth (Eaton's Fig. 4), there is no reason to suspect that this coefficient might be the Poisson's ratio of the various formations involved. 4. Until the field data supporting the empirical approach proposed by the author are presented and evaluated, the accuracy claimed in Conclusion 5 is without substantiation. References 1. Geertsma, J.: "Problems of Rock Mechanics in Petroleum Production Engineering", Proc., First Intl. Symposium on Rock Mechanics, Lisbon (1966) 585. 2. Haimson, B. and Fairhurst, C.: "Hydraulic Fracturing in Porous-Permeable Materials", I. Pet Tech. (July, 1969) 811-817. that the comments are those of a critic and do not offer an alternative and better method for the prediction of fracture gradients. Nevertheless, a reply is in order.

Jan 1, 1970

The petition for the formation of a Tulsa Section was granted. The final budget for the year 1917, and the tentative budget for the year 1918, were adopted. The Secretary was instructed to continue to send the Bulletin to all members whose dues have been remitted on account of their being in the war service, but to hold the Transactions and send them on request to the address furnished for the purpose. The issues of the Bulletin were presented to the Federal Fuel Administration, at its request, with the compliments of the Institute. Fifty-nine Members, five Associates, and fifteen Junior Members were elected. The resignation of one member was accepted. The clues of four members who are on active duty at the front were remitted. An extension of time for the payment of clues was granted to four members, upon request.

Jan 2, 1918

By David R. Maneval, W. E. Foreman, J. Richard Lucas

INTRODUCTION The objective of this chapter is to inform the industry, as well as the public, of the challenges in dealing with problems associated with air and water contamination by coal preparation plants. The need for an informed industry is most important. It is hoped that some contribution may be given to a more efficient and economical approach to the problems of plant waste contaminants at individual plants. The problem has many facets, and consideration should be given to specific areas before any significant problems develop at a given plant. It is then possible to have a reasoned approach before the pressures of an emergency environment force hasty and incomplete solutions. It will be necessary to anticipate these problems in the design of new preparation plants, and advance consideration should be given to all problems concerned with contaminants.

Jan 1, 1979

By T. P. Meloy

In a recent paper, Gaudin and Meloy1 derived a size distribution function for single, impact fracture. Mular2 extended the use of this size distribution to describe the output of carefully controlled grinding experiments. As it stands, the function is difficult to compute. Consequently, a series of tables of the function are presented below: where M(x) is the cumulative fraction finer than size x when x is particle size. Weight percents are tabulated for the single parameter, r, in three different size ranges: from 0 to 1, from 1 to 10 and from 10 to 100. Tables I, II and III are cumulative percent finer and Tables IV, V and VI are for weight percent passing screen size x, retained on the screen below. A number of conditions from the table are plotted in Figs. 1 and 2. Fig. 1 is a plot of the cumulative percent finer vs. size, and Fig. 2 is the weight per-

Jan 1, 1963

By A. D. Hodges

The process to be described, whatever other merits (or demerits) it may have possessed, certainly proved a financial success under the conditions of the locality where it was introduced and where a refining process had been sought previously in vain. I have ventured to bring it to the notice of the Institute in the hope that it may prove of some interest as a solution of a practical problem, such as is often presented to the metallurgist in the remote mining regions of the West. The method was used first at the Lyon Mill at Dayton, Nevada, and has been adopted at other tailings-mills on the Cornstock. These mills treat two classes of tailings: "sand," or; material which has passed previously through the pans of the ore-mills; and " slimes," or the fine clayey material which, coming from the battery, is too light to settle in the tanks inside of the mills but is

Jan 1, 1886

By U. K. Custred

To the layman, the term "strip mining" usually applies to the appearance of mined-over land after an operation is completed, not to the technique. This attitude, however, is becoming pass6 in the central Florida pebble phosphate field as eight mining companies in the area pursue a mutual program of land reclamation. The Florida phosphate industry is fortunate in this respect because it occupies an area favorable to reclamation. The terrain is flat; overburden is sand and clay which will support vegetation fairly readily; a high ground water table naturally converts mine pits into lakes. Too, this is water which readily supports marine life, not the acidic water so frequently found in the coal industry.

Jan 4, 1963

By G. W. Jarman

THE purpose of this paper is to present briefly a description of some of the special methods of separation or concentration, either singly or in combination with others, and to give certain operating data and examples. Explanation of the usual methods of large-production mill treatment, such as flotation or wet tabling, or of chemically treating industrial minerals, is not included in the scope of this paper, although one of these methods might be, in certain instances, augmented by one or more of the special methods that will be enumerated herein. Description of these special methods will be centered on magnetic separators, electro- static separators and air flotation or air tables. MAGNETIC SEPERATORS In general, separating is achieved by exerting upon a particle some kind of force opposed to gravity, either directly or at an angle. For example, in the Wetherill or cross-belt type of magnetic separator some particles are lifted vertically from the others because they have been exposed to a force to which they respond more readily than particles of lesser magnetic susceptibility. Of course, there is a limitation to this vertical rise, for the particle must be of a high enough susceptibility to receive a magnetic force greater than the 980 dynes per gram of gravitational urge. To overcome this limitation, the induction type of magnetic separator was developed, so that it is only necessary to instill, say, 30 to 60 dynes per gram instead of the 980, to cause a deflection away from the vertical in falling, and that deflection can be used advantageously when falling by inserting a dividing knife-edge. The induction magnetic separator (Fig. 1) has become a fairly well known method of concentrating and purifying. For example, abrasive grain was among the materials that did not respond to the previously best known type of magnetic separator, such as the Wetherill type, and the development of the induction magnetic separator in the plant of a

Jan 1, 1938

By J. L. Ratliff, R. I. Jaffee, H. R. Ogden, D. J. Maykuth

An experimental program was carried out to improve the low-temperature ductjlity of tungsten through the combined use of dispersed oxides for grain-size control and Groups VII and VIII metal additions for matrix softening. Separate binary -alloy studies showed that increasing amounts of finely dispersed thoria or zirconia and critical amounts of rhenium, osmium, and iridium were effective in significantly reducing the ductile-to -brittle bend transition temperature of tungsten as well as in increasing its re crystallization temper - LIKE most of the high-melting point bcc metals, tungsten undergoes a marked transition from ductile to brittle behavior with decreasing temperatures. The material factors which influence the transition temperature include grain size, metal purity, and the presence of dispersed phases. ature and decreasing its recrystallized grain size. The beneficial effects shown by each of these additions on transition temperature and grain size in binary combinations appeared to be additive in tevnary combinations. Thus, combined additions of 2 to 8 vol pct thoria with 5 pct Re, 0.87 pct Os, or 0.30 pct Ir were effective in lowering the transition temperature of tungsten pom 2000 to 75"C, increasing its re crystallization temperature from 1600 to 1800°C, and decreasing its recrystallized gain size from 1175 to 6800 grains per sq mm. The mechanism by which these factors are operable in tungsten is not yet clearly understood. Nevertheless, it has become increasingly apparent that the interrelationship of grain size and matrix composition governs to a large extent the degree of low-temperature ductility which can be achieved. Though it is not possible to accurately assess the relative importance of these variables, the available evidence suggests that, at low temperatures, grain-size effects predominate over purity effects. This was indicated in recent studies by Allen, Maykuth, and Jaffee,' involving single crystals containing 20 to 40 ppm 0 and 1 to 30 ppm C. Thus, while each

Jan 1, 1964

By P. A. Beck, W. D. Manly

In a recent note Sully and Head1 showed that the Cr-Fe sigma phase is isomorplious with the Cr-Co gamma phase, and that the lattice constants are also nearly identical. In a preliminary investigation of the ternary Cr-Co-Fe system at 800°C at this laboratory the above findings were confirmed, and it was found by microscopic techniques, using various etching reagents, that the two binary phases form an urinterrupted series of solid solutions with each other. These solid solutions occupy a straight narrow band which cuts across the 800°C isothermal section of the ternary system, connecting the two binary phases. A detailed investigation of the Cr-Co-Ni ternary system at 1200°C disclosed that here, too, the Cr-Co gamma phase extends deep into the ternary system in the form of a long narrow lip. The fact that this sigma type lattice is sustained even when well over half of the Co atoms in it are replaced by Ni atoms, with relatively little change in the Cr content, clearly indicates that Ni itself has a certain tendency to form the sigma phase with chromium. This tendency is hidden in the binary Cr-Ni alloys, where the sigma phase is not known to occur, but it becomes operative in the presence of a suficient amount of Co. The interpretation of these facts in terms of electron concentrations is rendered difficult by the uncertainty of our present knowledge of the valency electron structure of the transition elements in their alloys. However, Sully and Heal's results and the present work suggest that intermetallic phases with signla type lattice may occur more frequently in these little investigated alloys than heretofore suspected. In particular, it is expected that a similar phase may exist in the V-Co and perhaps in the V-Ni system, in analogy to the known sigma type phase in the V-Fe system, and that all these sigma type phases may form extensive solid solutions with one another.

Jan 1, 1950

By Frederick Crabtree

WHEN Professor Stock asked for a paper on the above subject, it was too late to prepare by June 1, or near that time, one that would involve any appreciable amount of experimental work or original research; but the suggestion was made that a review of the literature bearing on the subject might be submitted in good time, and that later this could be supplemented by any experimental data obtained during the summer, if experiments were carried out. In accordance with this suggestion, there are submitted the following notes on references found in the literature of recent years bearing on sulfur in gas. It is to be, understood that, ill general, these notes express the opinions of the authors whose papers are abstracted, not necessarily the opinions of the abstractors. Very little published information was found bearing directly on producer-gas sulfur, so this has been supplemented, in certain phases of the subject, by references to illuminating gas. Methods of analysis and processes for the elimination of sulfur from the gas are, without much doubt, very closely related in these two products. As in illuminating gas, sulfur is found in producer gas mainly as hydrogen sulfide, mixed with a much smaller and variable quantity of carbon bisulfide.1 The presence of minute quantities of other organic-sulfur compounds has been intimated, but no definite statement is made concerning these. The amount of sulfur present in producer gas is variable and depends on several conditions. The primary factor is the quantity of sulfur in the fuel, but the form in which the sulfur exists, the temperature of the producer, the air-steam ratio, and the efficiency of the scrubbing process are all determining factors. When the coal used contains less than 0.5 per cent. of sulfur, the sulfur in the gas will not exceed the quantity found in the average illuminating gas.2 Sulfur in producer gas may safely

Jan 9, 1919

By R. H. Goodrich

Development in this district during the year 1929 was little different from that of any other year despite the somewhat depressed condition of the oil business in general. The year was marked by: (1) An intensive geophysical campaign in the search of deep-seated salt domes; (2) the rather successful exploration and development of lateral sand production on the flanks of some of the older domes. Geophysical Exploration Geophysical work is confined almost exclusively to the torsion balance and seismograph. At the beginning of the year there were approximately 185 individual instruments of all types engaged in the search of structures in the Gulf Coast of Texas and Louisiana. This total includes 3 magnetometers, 83 torsion balances and 100 seismographs. The number of parties operating the torsion balances was 47; seismographs, 20; magnetometers, 3. It is estimated that 4,800,000 lb. of dynamite or other explosives were used in seismic exploration. During the year the torsion balance and seismograph were credited with having discovered the following salt domes: Texas, Danbury dome, Brazoria County, H. & T. B. R. Co., and Clodine dome, Fort Bend County, John Fredricks and Wm. Stanley, Satowsky Survey; Louisiana, Iowa dome, Calcasieu and Jefferson Davis Parishes, T. 9 S., R. 6 and 7 W., and Cameron-Meadow dome, Cameron Parish, T. 14 S., R. 13 W. Because of the secrecy maintained in these developments, it is somewhat hazardous to venture opinion as to the number of salt domes found during one year. The discovery of gas at Mykawa district and at Genoa district, in Harris County, Texas, is considered of more than passing importance, because there is indication in the performance of these two districts that commercial accumulation of oil and gas may be found in the Gulf Coast on structures other than the wore or less definite salt dome type. While it is generally conceded that the accompanying structure in these instances are deeply buried salt domes, it is a fact that neither the seismograph nor the drill have indicated the presence of salt.

Jan 1, 1930

By S. R. Rao, J. Leja, K. S. Moon

A prolonged grinding of sulphide ores in steel mills appears harmful to flotation recovery and selectivity whenever xanthates are used as collectors. Particles finer than about 10µm show a pronounced decrease in floatability. A supposition was made that the cause of the reduction in floatability of ground sulphides is the presence of metallic iron abraded during grinding and deposited on the ground particles. Electro- chemical measurements were made of mixed potentials developed by different sulphide-mineral electrodes (galena, chalcopyrite, pyrite, marmatite, pyrrhotite) in xanthate solutions, without a direct con- tact or in contact with a metallic iron electrode. These measurements showed that without a galvanic contact between the sulphide and the iron, the values of mixed potentials were in the vicinity of the xanthate/dixanthogen redox potential. When contact with iron was established, the mixed potentials shifted towards the more negative reducing or cathodic values. The shift was greater the higher was the ratio of the surface areas: iron electrode to sulphide electrode. Further, the shift in mixed potentials was greater the more reducing were the conditions on the sulphide electrode. Chemical analysis of reaction products produced on the surfaces of sulphides and in the bulk solution showed that less thiosulphate was formed in all of the sulphide-xanthate systems and that more elemental sulphur was detectable on the pyrite and marmatite surfaces. Adsorption of xanthate parallels the amount of thiosulphate formed with which xanthate is exchanged by metathesis. If the supply of oxygen is limited, the demand for oxygen by the abraded metallic iron competes with that by the valuable sulphide, resulting ultimately in poorer hydrophobicity. If excessive amounts of pyrite or pyrrhotite are present as well, the conditions are so reducing that there is little adsorption of xanthate ions on the valuable sulphides to make them hydrophobic and floatable. The presence of increased quantities of sulphur on pyrite or marmatite is responsible for a non-selective flotation. Flotation tests on synthetic mixtures with and without metallic iron powder in the feed confirmed the above conclusions from electrochemical and chemical measurements.

Jan 1, 1976

By L. A. Mekler

THE recirculating furnace is primarily a heating apparatus of the convection type in which the heat-absorbing surfaces are heated by a mixture of fresh products of combustion and a portion of the combustion gases that have already given off a part of their heat in their previous passage over the heat-absorbing surfaces. In its basic conception, the recirculating furnace can be considered as a closed thermal system in which the heat-absorbing surfaces are .constantly swept by a fixed quantity of products of combustion at a given initial temperature with the gases being constantly returned to the furnace and reheated before they again enter the heating zone. Gases equal in amount to that produced by the fuel burned to reheat the circulating gases are constantly ejected from the system to the stack. The recirculating furnace is the most suitable apparatus for heating by convection where low furnace temperatures must be maintained and where only a small portion of the available heat is taken out of the gases, particularly where the maximum allowable furnace temperature is low and where the final temperature of the gases is only a few hundred degrees below their initial temperature. In such cases, recirculation not only provides a method of reducing the rather high combustion temperatures of the fuel when burned without a large amount of excess air, but, by returning to the furnace the heat content of the gases at their final temperature, recovers a large portion of heat that otherwise would have been lost through the stack.

Jan 1, 1928

By W. L. Martin, J. N. Dew, H. B. Steves, M. L. Powers

This paper presents and discusses the results obtained during a pilot test in the Loco field in southern Okla homa. The test was conducted in a 2%-acre pattern that was part of a 20-acre conventional waterflood pilot area. The conventional flood was well past its economic limit when the hot waterflood was initiated to obtain technical information and operating experience. Temperature data from nine observation wells showed that about 75 percent of the pattern was affected by heat, and that heat losses were severe in the pilot pattern. About 60 percent of the injected heat was lost to overburden and underburden zones during hot-water injection. Wellbore heat losses were held at tolerable levels at the shallow depth of the test by providing a low-pressure air annulus between the injection tubing and well casing. Hot water provided water injectivity increases of 200 to 400 percent. The hot water channeled across the lower portion of the oil sand in three directions through zones of relatively high water saturation. There was no conclusive evidence that natural fractures or pressure partings aflected the flow of fluids in the pilot pattern; however response undoubtedly was aflected by localized pressure gradients and by injection-production rate ratios. The results showed that hot waterflooding increased oil recovery in a reservoir containing 600 cp oil. The total tertiary oil production from the pilot pattern area was 3,896 bbl or about 156 bbl/acre-ft swept by heat. The corre.sponding WOR was about 34:I. Description of the Hot Waterflood Process To hot waterflood an oil reservoir, water is injected that has been heated to a temperature substantially higher than the original reservoir temperature, but lower than the vaporization temperature of water at the prevailing pressures. In the reservoir the hot water flows continuously into cooler sand and rapidly loses heat to the sand until it has been cooled to the original reservoir temperature. Thus, a heated zone and a region or "bank" of cooled water begins to accumulate immediately after hot water injection is started. This bank of cooled water continues to grow ahead of the heated zone, which also grows, but at a slower rate. This occurs because heat transfer is almost instantaneous, and the ratio of heat capacities of water to rock is such that two or three unit PV of hot water must be injected to heat a given unit bulk volume of the reservoir. The primary displacement mechanism is the same for both hot and conventional cold waterfloods; i.e., "piston" displacement occurs at the original reservoir temperature. The incremental benefits of hot waterflooding usually occur long after the breakthrough of cold water at producing wells, and the increased oil recovery necessarily is accomplished with high WOR's (water-oil ratios). Heat decreases the viscosity and density of oil and water. These effects result in more rapid and increased recovery of secondary or tertiary oil. If the cost of the required heat is low enough, the ultimate oil recovery of a hot waterflood should be increased substantially over what would be expected at the economic limit of a conventional cold waterflood. The economic benefits of any hot-fluid injection project depend primarily upon the cost of the heat required to produce more oil at an increased rate. This cost depends in part upon the amount of heat lost to surrounding formations. Heat loss depends upon reservoir thickness, water injection rate and temperature, the depth of the formation, well spacing, and the characteristics of the reservoir rock and surrounding formations. In general, percentage heat losses decrease as injection rate and reservoir thickness increase. Although it is an old idea, hot-water injection has not received widespread field application in the oil industry as a drive process. Much of the original field work with hot water was done in Pennsylvania fields where water permeabilities and injection rates are low. In these cases, hot-water injection was used primarily as a means of increasing in-jectivities — not as a recovery process. Ramey' recently has published an excellent review of the development of hot fluid injection processes. Recent publications"' and our own experiences now indicate that hot water or steam injection also can effectively increase the oil recovery from reservoirs containing viscous crudes. However, the economics of these methods as displacement processes have not been established. Several theoretical predictive techniques have been published (for a review see Ramey'), but simplifying assumptions make

Jan 1, 1969

Article IX of the Bylaws constitutes the basic instructions to the Nominating Committee The first duty of the Nominating Committee is to select a candidate for Director and President-elect It is desirable that the successive Presidents from year to year be men of differing professional interests so selected that over a period of years each major group in the Institute will be represented in the Presidency a number of times bearing some reasonable relationship to the numerical strength of that group in the Institute In Section 2 of Article IX it is stated that "a sufficient number of Directors be selected on the basis of geographical districts so that each district will have at least one representative" These districts, as now established, are shown in the accompanying map There are ten districts including the New York metropolitan district Each of these districts is entitled to one Director, except the metropolitan district which is entitled to six Each year each district, the term of whose officially recommended Director expires, shall suggest a candidate and if desired an alternate candidate to the Nominating Committee to fill the vacancy If a candidate and an alternate are suggested they should preferably have different Divisional or Branch affiliations The Chairmen of the Sections In the district shall constitute a committee to select the candidate or candidates The Sections shall rotate the chairmanship, as shown in the Appendix to this instruction It is desirable that in filling a quota vacancy in any district, the selection be made from the name or names suggested by the district

Jan 1, 1952

By D. E. Baldwin

A method has been devetoped for predicting the produced concentration profile for a miscible slug in a five-spot pattern. The technique consists of dividing the five-spot into radial etements and applying an approximate radial solution of the dispersion equation to each element. To test the method, laboratory experiments were conducted in five-spot models. The models were 2-ft X 2-ft X 2-in. Berea sandstone slabs simulating one quarter of a five-spot. An aqueous system was used with tritiated water as the tracer fluid. Effiuent concentration profiles were obtained for slug sizes ranging from 0.7 to 10.2 per cent of the pore volume. Agreement between predicted and experimental profiles was excellent. A prediction was also made for a field tracer test. For this case the predictive technique was modified to account for stratification by use of a layer cake model. INTRODUCTION Dispersion in porous media is of growing interest to the petroleum industry because of the increasing importance of secondary recovery operations. One of the controlling factors in the recovery of oil by miscible displacement or by the use of waterflood additives is the degree of mixing between the fluids of interest. Consequently, one of the prerequisites of any recovery prediction is an adequate method of predicting dispersion. Also, any quantitative interpretation of waterflood tracer tests is dependent upon the ability to determine the dispersion of the tracer as it flows through the reservoir. During the past few years there have been reported in the literature the results of a large number of investigations, both theoretical and experimental, concerning dispersion in porous media. (An excellent review of these results has been presented by Perkins and Johnston." Only a few of these investigations, however, deal with non-lin-ear flow systems. Raimondi et al.9 have presented an approximate solution of the dispersion equation for radial, diverging flow. Lau et al. 7 and Bentsen 1 have presented laboratory data for radial systems and have shown that the dispersion can be adequately predicted by Raimondi's solution. Bentsen has also presented a small amount of data for a radial, converging system. Brigham and Smith' have applied Raimondi's solution, with approximating assumptions, to a five-spot pattern to predict the behavior of a field tracer test. The afore-mentioned investigations have been concerned almost entirely with radial diverging flow and have neglected the effect of converging flow. For this reason the present investigation was undertaken to develop a method of predicting dispersion in a five-spot pattern including the effects of both diverging and converging flow. The method which was developed consisted of dividing the five-spot into diverging-converging radial elements and applying an approximate solution of the disperson equation to each element. DEVELOPMENT OF PREDICTION METHOD The development of the prediction method consisted of two phases: construction of a radial model of a five-spot pattern and derivation of equations to describe the dispersion in the radial model. FIVE-SPOT MODEL A radial model which simulated the flow characteristics of a five-spot pattern was constructed by dividing the five-spot into diverging-converging radial elements (Fig. 1). Because of symmetry the model represented only an octant of a complete five-spot. Each element had an included angle of l° (making a total of 45 elements) and a radius r, such that the sum of the individual element areas was equal to the area of the five-spot octant. The normal five-spot fractional flow behavior was determined by averaging the experimental five-spot data of Caudle and Witte,' Dyes, Caudle and Erickson 5 and Fay and Prats. 4 The resulting curve is shown as a solid line in Fig. 2. To match this curve with the radial model it was

Jan 1, 1967

By Charles H. J. Patterson

When coal is deposited on the decks of pneumatic tables, all fine particles clinging to the larger pieces are blown free by the air. Inasmuch as the air retains an appreciable residual velocity after passing through the bed of coal, it is capable of suspending particles of goodly size. This velocity is dissipated gradually and, unless confined, can readily extend beyond the limits of the plant. Today the ideal in the design and operation of pneumatic cleaning plants is not that they be no dustier than the ordinary tipple, but rather that they be as clean as an office or shop. This degree of perfection may not yet have been attained in any commercial plant, but it is not impossible of achievement. Not until recently has the recirculation principle been applied to pneumatic separating plants. In the writer's estimation, it has not yet been proved entirely satisfactory in commercial installations. A serious obstacle lies in the fact that it is practically impossible to provide a truly closed circuit. The air circuits must be interrupted at certain points, if only for the introduction of raw material and for the recovery of the finished product. It is feasible to prevent the escape of polluted air at these points, but this can scarcely be accomplished without admitting additional air into the circuit. These additions of air are cumulative, which necessitates means for emitting to the atmosphere the excess while still carrying its objectionable burden, if provisions are not made for conditioning. If it must be provided at all, conditioning is frequently simpler and more economical if applied to the entire volume of air involved. This procedure eliminates the extra initial cost and operating expense of the closed system. Crane Cheek Experiments The first noteworthy commercial installation of pneumatic equipment was made in 1922, at the Crane Creek plant of the American Coal Co. of Allegheny County, at McComas, W. Va. Six tables for cleaning coal between the limits of and 3 in. comprised the initial installation. Dust was collected by hoods connected by a system of ducts to exhauster fans. In this installation the unit dust burden was small, owing to the removal of fines from the feed by vibrating screens.

Jan 1, 1931

By A. Adiaddevich

Petroleum has been found in Russia in various localities from north to south, as may be seen from the list given below: (a) In the basin of the Petchora river, Northern Russia. (b) In the basin of the Volga river, in the governments of Samara and Saratoff. (c) In the government of Astrakhan and in the Uralsk territory, close to the northern and eastern coast of the Caspian sea. (d) At Grozny in Northeastern Caucasus. (e) In the Daghestan territory, Eastern Caucasus, on the Caspian sea. (f) On the Apsheron peninsula (Baku and other districts) close to the Caspian sea shore. (g) On the island of Tcheleken in the caspiah sea, also on the island of Sviatoi. (h) In the Transcaspian territory on the Neftianaia Gora (Oil hill) and on the surrounding hills. (i) In the Ferghana valley in Russian Central Asia. (j) On the Kertch-and Taman peninsulas on the Black sea. (k) In Siberia it has been discovered in the Transbaikal territory and on the island of Sakhalin.. ' ' In the above-mentioned districts petroleum has been found to exist under different geological conditions and to vary in its chemical and physical properties. At the present time petroleum is produced in Russia at Baku, Grozny, on the island of Tcheleken, in the Ferghana district, and in the Uralsk territory. The yearly production in 1912 throughout the Russian Empire amounted to 69,400,000 barrels, of which the Baku fields were responsible for 52,000,000 barrels. This shows that the Balm fields on the Apsheron peninsula are the chief oil-producing centers in Russia, being at the same time the oldest of all our oil fields. In this paper I shall discuss the Baku fields only, leaving all the others until a later date. The Apsheron peninsula in the Eastern Caucasus protrudes into the Caspian sea in the shape of a triangle some 47 miles long covering a total area of some 750 square miles. The eastern part of the peninsula is a flat, slightly rolling plain, rising in its highest parts to 140 to 170 ft. above

Jan 1, 1915

Andes Copper has an old camp and a new camp, both isolated until recent road improvements. The old camp is at Potrerillos and the new one at El Salvador, 25 road ,miles away. The company was incorporated in 1916 and the first mine, concentrator, leaching plant, smelter and town were built in the succeeding twelve years. The first blister copper was poured on January 24, 1927. Economic conditions determined the long development period but the end result was the design and construction of a mining complex that was all of a piece, unlike the piecemeal additions to El Teniente and Chuqui. The mining episode at Potrerillos came to an end in 1960 when the ore at La Mina became exhausted and the new mine, El Salvador was brought in. Both of these ore deposits come within four hpundred feet of the surface and had they been developed within the last five years might reasonably have been brought in as open pit mines. However, that is conjecture, and as it stands the operation at La Mina was so ideal for the mining method selected, blockcaving, it became a classic for the textbooks. On the other hand, El Salvador has turned out to be a blockcaving mine to test an engineer's skill. In mining the copper deposit at Indio Muerto mountain, there are ground conditions of every conceivable type. Tunneling in one section, the back can cave like sized pea gravel and only spiling can hold it; in another heading only the lifters are shot but often the rest of the round will sit down in one piece; elsewhere the bottom squeezes up and closes the drifts; and contrary to all other locations, there are sections where the block can be undercut without support. Today the scope of operations at Andes extends from mining to electrolytic copper. Ore is mined at El Salvador and the concentrator is also situated there. Concentrates pipelined 14 miles to Llanth, the water decanted, and then it is hauled by rail 40 miles and 5500 ft higher to the Potrerillos smelter and refinery. Potrerillos and El Salvador are respectively 90 and 70 miles from the port of

Jan 11, 1969

By Henry Rawdon

ANY laboratory corrosion test, as judged from the practical point of view, is valuable only to the extent that it foretells what will, in all probability, occur in service. Such a test is most properly to be considered as a "pilot test, " that is, a test which indicates the direction along which action may be expected to occur rather than as a truly quantitative test which would be expected to tell just how and to what extent the action would proceed. It is generally recognized that laboratory corrosion tests should be chosen with particular reference to the character of service expected for any particular type of metal, so far as it can be foreseen. Even when this requirement has been fulfilled, however, the question whether the actual service behavior of the material is in accordance and general agreement with predictions based upon such laboratory tests is always a pertinent one. The information available in the technical literature bearing on the correlation between the service behavior of metals from the corrosion standpoint, and the results obtained with the same metals in laboratory corrosion tests is very meager, indeed. The results which have been obtained in weather-exposure tests of sheet duralumin which form the body of this discussion are presented here for their bearing on this particular phase of the problem of the corrosion resistance of duralumin. Although the exposure tests described have not been completed, in the sense that all of the tests, in the series initially laid down, have been accomplished, still the general trend shown by the results is so clear that a number of definite conclusions at this stage (subject, of course, to possible modification in the light of later results) are believed to be warranted. The tests reported upon here form one phase of the much broader study of this subject which has been under way for several years in which the National Advisory Committee for Aeronautics, the Bureau of Aeronautics of the Navy Department, the Army Air Corps and the Bureau of Standards have cooperated. Without the very helpful cooperation of the manufacturers in furnishing the

Jan 1, 1929