Search Documents

By Robert D. Pehlke, Weldon L. Daines

The reduction of manganese oxide from a basic slag by silicon dissolved in liquid iron at steelmaking temperatures was studied to determine the rate-controlling step for the process. The experiments were carried out under an argon atmosphere in a resistance-heated vertical-tube furnace. The two liquid phases, slag and metal, were held in zirconia crucibles. Sampling and chemical analysis of the slag phase led to time-concentration curves for the system. Results obtained by varying parameters such as temperature, stirring rate, concentration, and melt geometry defined the limiting reaction mechanism. The reduction of manganese oxide by silicon is a fast reaction and reached equilibrium within 90 min. The rate of stirring has a marked effect on the reaction rate, while, on the other hand, the effect of temperature is very small. This identifies the rate-controlling step as diffusion rather than interfaciul chemical reaction. The variation of other parameters revealed that a) diffusion of manganese in the iron phase is the slow step, b) the value of D/6 for manganese in iron at 1550°C is 7x 10-4 cm per sec, c) the energy of activation for the apparent rate constant is 7 kcal per mole, and d) increasing the amount of silicon in the iron decreases the diffusion coefficient of manganese. THE equilibrium relations pertinent to the reduction of manganese oxide from a steelmaking slag by silicon dissolved in liquid iron have been studied, but little is known about the mechanisms that control the rate of the process. The purpose of the present investigation was to study the rate of reduction by silicon and to determine the rate-limiting step. The effects of stirring rate, temperature, composition, and melt geometry were investigated as a means of identifying the controlling step. On the laboratory scale, relatively little work has been done in the area of slag-metal kinetics, primarily because of the problems confronted in attempting to contain liquid slags and metals in laboratory crucibles at steelmaking temperatures. Since graphite is an ideal material for a crucible, several investigations have been carried out on the reduction of various oxides from a slag by carbon in graphite-saturated iron and on the transfer of sulfur between a slag and graphite-saturated iron. Most of this work has been performed in induction furnaces. Studies where the container was not graphite are extremely limited. A single kinetic study of manganese transfer between molten iron and basic slags was carried out by Sano, Shiomi, and Matsushita.' These investigators prepared calcium oxide and titanium oxide crucibles to contain the two-phase system. Only a few experiments were carried out and the results had to be treated qualitatively. Despite the paucity of kinetic data, a large quantity of information is available in the literature concerning the thermodynamics2-12 and physical properties'3-21 of the slags containing manganese oxide and the dilute liquid iron alloys containing manganese and silicon which were involved in this research program. EXPERIMENTAL METHOD A vertical-tube resistance-heated furnace was used in this investigation to study the slag-metal reaction Although most previous slag-metal studies were carried out in induction furnaces, a resistance furnace has several advantages including better control of temperature and stirring rate. Hence, a resistance furnace was selected for this study, and its design is shown schematically in Fig. 1. Slip-cast, fine-grained, low-porosity, lime-stabilized cubic zirconia crucibles were used for the kinetic experiments. The crucibles were 4 1/2 in. high and 2 1/8 in. OD with a 1/16-in. wall. The crucibles were only slightly

Jan 1, 1969

By A. F. Melcher

The present paper is a progress report on an investigation of the physical factors of oil and gas and especially of their sands,' such as pore space, size of pores or permeability, retentivity, viscosity of the oil, temperature, pressure, thickness and area of the pay sand, water relations, and capillarity. The purpose is to determine as many of these physical factors as possible, and to ascertain the relations existing, directly or indirectly, between these physical factors and the production of oil and gas. As yet only pore space2 and size of grains of pay sands have been investigated, although an apparatus has been designed to determine the permeability of a sand to oil, water, or gas under definite drops of pressure between the entrance face and exit face of the sample. Messrs. E. W. Shaw, R. Van A. Mills, D. Dale Condit, G. B. Richardson, G. C. Matson, and C. H. Wegemann collected the samples upon which the physical determinations were made. Acknowledgment is made to my colleagues of the United States Geological Survey for many suggestions and criticisms; to Mr. Mills for the production data given of the oil wells from which some of the samples were collected; to Mr. A. W. McCoy of the Empire Gas and Fuel Co., Bartlesville, Okla., for many ideas. Determining Pore Space of Oil and Gas Sands In selecting a method for the determination of pore space, two objects were kept in mind: First, the method must not only be sufficiently

Jan 1, 1921

By H. W. Young

Development of high-tension outdoor substations during the past few years has been due primarily to economic reasons. The demand for power in small communities could not be met with the conventional and Fig. 1.—33,000-VOLT step-up outdoor air-break switch and substation installation outside of a powerhouse generating at 2300 volts stepping up to 33,000. Twenty-one coal mines are supplied from lines leading from this installation. comparatively expensive indoor types unless the rate for service was materially increased. To prove that the problems lncident to development have been solved successfully, it is only necessary to point to the wide adoption of outdoor substations by utility companies. Passing at once to the question as to whether outdoor substations are applicable to

Jan 1, 1920

By F. A. Olson, S. L. Pohlman

A unique method of measuring weight loss as a function 3 of time, with a sensitivity of 10-5 grams, while leaching copper minerals with a flowing acid leach solution has been developed. Kinetic results obtained coupled with visual and microprobe analyses show topochemical reaction for the leaching of chrysocolla with sulfuric acid. The kinetics follow a shrinking core model and show ion diffusion through a product layer, chemical reaction at the unreacted core interface and mass transfer through the boundary layer as being important.

Jan 1, 1974

For the third year in a row total value of the Nation's mineral production broke all previous records. A new peak of $20.4 billion was reached in 1964. So says the U. S. Bureau of Mines. The Bureau's preliminary estimate for 1964 is $800 million higher than the value reported for 1963, and $1.6 billion greater than the 1962 figure. The unprecedented demand for minerals, has stimulated development of new mines and expansion of processing capacity in many parts of the country.

Jan 2, 1965

By Harold R. Wampler, John L. Bolles, Adrian J. Broderick

Phelps Dodge's 60,000 tpd Morenci Concentrator has been in operation since 1942. The integrating of process control applications into the concentrator began in 1972. A process control system is presently on-line controlling 30 primary grinding circuits and all reagent additions. The system consists of a centralized control room process control Computer, on-stream X-ray analyzer, on-stream particle size analyzers and an operator interface. This paper describes the process control system's development, control concepts and its influence on the concentrator performance.

Jan 1, 1978

By A. U. Seybolt

A. U. Seybolt (General Electric Research Laboratory)— As pointed out in an earlier paper,41 it appears to be very difficult to nucleate Si3N4 in Si-Fe of silicon content up to around 5 pet. Therefore, one observes, as did Pearce, that equilibrations with nitrogen gas yield only nitrogen in solid solution at temperatures above about 700°C, or, as Pearce found, 770°C. Evidently, the free energy of formation of Si3N4 only becomes high enough at -770°C to overcome the reluctance of Si3N4 to nucleate. However, as mentioned in Ref. 41, if some Si3N4 is first formed by a mixture of ammonia and hydrogen, one can then replace this gas mixture by nitrogen gas, and either increase or decrease the amount of Si3N4 present at any temperature by suitable adjustment of nitrogen pressure: that is, to equilibrate with Si3N4. In the equilibration experiments cited in Ref. 41, equilibrium was approached from both sides, and it was found that samples up to 944oC, at least, were in equilibrium with Si3N4. Higher temperatures were not employed, as this would have necessitated a redesign of the apparatus for using nitrogen pressures in excess of 1 atm. To summarize, the results of Pearce's experiments and those of Ref. 41 cannot be directly compared because two quite different equilibria were studied. Therefore, the statement by Pearce on p. 1398 indicating apparent error in Ref. 41 is unjustified. M. L. Pearce (author's reply)— There was limited evidence obtained in the current investigation which would indicate that excessive "supercooling" did not occur. A small piece of the same resulting from heat treatment No. 5 in Table III was subsequently held at 800°C for 16 hr in 95 pet N-5 pet H. Isotope-

Jan 1, 1964

By E. H. Griswold

The efforts of petroleum production engineers during the past year have largely concentrated upon ways and means of reducing operating investments and expenses in order that the industry may survive a period of low crude oil prices. Major progress was made in outlining and solving the technical problems pertinent to unit operation in order that executives and legal staffs may actually arrange operating contracts to effect unit operation. Consequent savings in development and operating costs, accompanied by increased recovery, will thus be obtained. Well spacing has received considerable constructive thought and study, from which practical results are assured in the near future. The control of edge and bottom waters has advanced in technique through the engineering work done in Yates, Hobbs and East Texas, and there is evidence of greater cooperative efforts between engineers to increase recovery from pools by mutual gas conservation. The use of pressure control by surface and bottom-hole chokes has become general practice to reduce gas-oil ratios. The study of bottom-hole pressures has led to new conceptions of proper utilization of reservoir energy and maintenance of pressure by natural means. Pressure gradients of flowing wells have been measured in practice and strides made to develop workable formulas for the flow of oil and gas mixtures through vertical pipes. The information thus obtained will permit the intelligent design of flow tubing combinations. Gas-lit and repressuring advancements have been few, due to overproduction from naturally flowing wells. Satisfactory unloading valves for gas-lift wells have been developed and consistent progress made in gas-lift displacement pumps. The necessity for producing wells at high rates of flow while producing large quantities of sand has resulted in radical changes in Christmas tree and separator designs for the Oklahoma City pool. The opening of wells to obtain potential production for proration purposes has been eliminated in the Yates and Hobbs pools by the application of engineering principles.

Jan 1, 1932

By R. H. Sweetser

There are probably as many variations of the method for blowing-in blast-furnaces as there are furnace superintendents. That some of these variations are poor practice is shown by the troublesome and sometimes disastrous experiences of many furnace-men, even within the last few years. It is the object of this paper to put on record a blowing-in practice that has gradually developed to the point where the results are sure, safe, and satisfactory; and also to bring into discussion several variations that are questionable. The blowing-in of a modern blast-furnace is one of the greatest of metallurgical operations. On its degree of success depends much of the future life of the lining and the subsequent behavior of the furnace; and it involves possibilities of danger to the men engaged in the work. The objects to be attained are the heating of the interior of the furnace to the high temperature necessary for smelting iron; the starting of the smelting process; and the gradual movement of the stock in its downward course. The most critical points are the placing of the kindling-wood, the " bringing down " of the gas, the closing of the iron-notch, and the first cast. The lighting of the first gas, the opening of the cinder-notch for the first flush, and the running of the first cast are anxious times for the superintendent and the furnace-men. Drying-Out the Furnace. As soon as a furnace-lining is completed it should be thoroughly dried out, whether it is to be blown-in soon or not; and the longer it is dried, the better for the furnace. At least two weeks is desirable; but good results can be had with 10 days of firing. The crudest and least desirable method of drying is to build a wood fire in the bottom of the furnace, throwing the wood in through a tuyere-arch, and using the iron-notch for

Jan 1, 1913

By Leslie F. Tedsen, John E. Dorn, Alan E. Flanigan

It is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references I to 4. Investigations on the properties at elevated temperatures are few, however, and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. AS is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hard- ening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "averaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: 1. The higher the temperature, the more rapidly is the fully aged condition attained. :7

Jan 1, 1946

By Leslie F. Tedsen, Alan E. Flanigan, John E. Dorn

It is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references I to 4. Investigations on the properties at elevated temperatures are few, however, and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. AS is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hard- ening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "averaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: 1. The higher the temperature, the more rapidly is the fully aged condition attained. :7

Jan 1, 1946

By K. B. Nowels

Data pertaining to pipe line flow for both oil and gas in horizontal or nearly horizontal pipe lines are both extensive and accurate. However, the pipe formulas used to determine pressure drop for flowing fluids (liquids and gases) under conditions of horizontal flow are not generally applicable to flowing oil and/or gas wells. Except for some data developed in small laboratory set-ups, little or no information was available concerning flow of oil and gas mixtures in vertical pipes, when, in 1928, the writer began the development of a method for computing pressure drops in the pipes of flowing oil wells, as outlined in this paper. In 1929, Urenl presented some findings based on laboratory experiments in which vertical flow of an extremely heavy crude oil was induced by means of air through a 2-in. pipe, 41 ft. long. The friction factors derived from the experiment, as well as values for pressure drop per 100 ft., are not believed satisfactory in their application to flow problems in the field. Versluys,2 also in 1929, presented a mathematical development of the theory of flowing oil wells, and in 1930, gave a companion paper3 setting forth some principles governing the choice of length and diameter of tubing in oil wells. Since the termination of the study presented in this paper, another valuable contribution pertaining to the problem of vertical flow was made by Moore and Wilde.4 Although there were writings dealing with the principles of the gas-lift, a search of the available literature indicated that specific information on vertical flow was lacking with the exception of the writings of Uren, Versluys, and Moore and Wilde, to which reference has been made.

Jan 1, 1932

By Jean L. Leroy

The Lead Smelting works of Metallurgie Hoboken S.A. are located on the banks of the river Scheldt a few miles South of Antwerp. Lead refining began at Hoboken in 1687, when it was restricted mainly to desilverizing lead bullion from Central America. Since then, various changes have been made to develop the works into a comprehensive and integrated custom smelter and refinery. Multiple hearth roasting furnaces, down-draft sinter machines and blast furnaces of standard design are used for the treatment of "complex" lead ores and secondary materials. A lead refinery based on the Harris process, with Parkes desilverizing followed by vacuum dezincing and Kroll Betterton debismuthizing was commissioned in 1967. Facilities for the recovery of precious metals, bismuth, antimony, arsenic and sulfuric acid are available. Special problems arise from the presence of large quantities of copper in the materials treated.

Jan 1, 1970

By AIME AIME

OUT of the fabulous iron ranges of Michigan?s Upper Peninsula since Pearl Harbor have come go to the steel mills to become tanks, guns, ships, and other weapons for a United Nations' victory. But the contributions to the war effort, as far as Michigan's iron country is concerned, do not stop there. The same men who mine iron ore deep inside the earth also are "mining" on top of the ground, gleaning a harvest of scrap iron and steel that is writing a big chapter in the War Production Board's salvage program. At virtually every mine over an area of a hundred square miles, everyone from the top mine official and straw boss to the man in the dippings is scrap conscious. They know the importance of the ore they mine but they are equally familiar with the importance of iron and steel scrap in war production. The successful job they are doing in salvage is a tribute to the entire Upper Michigan mining industry and to the man who marshaled them into action-John M. Bush, chief of the land department for the Cleveland- Cliffs Iron Co. at Negaunee, and for ten years an A.I.M.E. member. Also, this job should be an inspiration to 611 mining. metallurgical, and petroleum communities as to the latent possibilities of organized scrap recovery.

Jan 1, 1943

By O. A. Kiehn, C. A. Born, F. N. Bender

Development of the flotation reagent scheme at Climax Molybdenum Company's mine at Climax Colorado is reviewed. Features of the mineralogy, milling practice and background of reagent changes are outlined. Special attention is given to the hitherto unpublished details of the application of depressants for copper and lead impurities. The present rougher flotation reagent scheme utilizes a neutral hydrocarbon oil, low in unsaturates and wax, as collector with a sulfated coconut oil emulsifier and pine oil frother. Lime and sodium silicate are used as rougher conditioning and slime dispersant agents. Chalcopyrite and galena impurities are depressed in both rougher and cleaner plants by stage addition of Nokes reagent and sodium cyanide to yield a metallurgical grade molybdenite concentrate containing greater than 90% molybdenite and less than 0.5%, 0.1% and 0.05% iron, copper and lead impurities, respectively.

Jan 1, 1976

By J. E. Pogue, F. G. Coqueron

This paper describes the sources of funds required by the petroleum industry to finance capital expenditures and also presents a discussion of the effect of rising construction costs on these expenditures. The petroleum industry obtains its capital funds from several sources: (I) internal, from retained cash earnings; and (2) external, from borrowings and the sale of securities to the public. The upward trend of capital expenditures of the petroleum industry is caused in the main by the influence of two powerful factors: (I) the physical growth in the demand for oils; and (2) the rising cost of drilling wells and constructing refineries, pipe lines, and other facilities. The segregation of these factors is accomplished by deflating the actual capital expenditures so that they are shown in terms of 1939 costs and then subtracting the adjusted series from the actual figures to yield a set of data representing the expenditures made on account of higher costs. Rising costs affect prices and the portion attributable to this factor had to be generated from the cash earnings of the industry, which called for higher oil prices. Introduction Capital may be defined as "wealth employed in or available for production." All production requires capital. Expanding industries require more capital than static ones, and technological industries employ more capital than. those in which little equipment is needed. The petroleum industry is both rapidly growing and highly technological, and, being a large industry, its capital requirements are prodigious, amounting to about one-seventh of the total of all American business, excluding agriculture.* Capital formation may be defined as the method by which the wealth or capital needed in the productive processes is created. There are various ways in which capital funds may be obtained but there is only one way in which capital can be created—out of production in excess of consumption, that is, savings. The physical realities are simple, but the monetary concepts are complicated because the mechanism of credit can draw upon future savings. Source of Capital Funds An industry, such as the petroleum industry, can obtain its capital funds from

Jan 1, 1949

By Charles Maier

PART I DENSITY AND ENERGY CHANGES IN COLD-WORKED COPPER IT has long been supposed that when crystalline materials are com-minuted the energy used in the production of increasingly smaller grain sizes is not entirely dissipated as heat but that a certain portion is "stored" as a part of the internal energy of the material. This portion usually has been called the "surface energy" of the particles. The practical interest of the Bureau of Mines in this subject in connection with the energy requirements of crushing processes has led' to the author's attempt to measure the "stored" energy in finely divided calcite by heat-of-solution methods1. The experiments on calcite showed that "storage" of energy could not be proved for this material, because fine grinding caused a lack of chem-ical homogeneity evidenced by loss of carbon dioxide and subsequent adsorption of water on the surfaces of the calcite particles. When thermochemical correction was made for composition changes the cor-rected heat of solution was less for fine material than for coarse. Con-tinuation of the experimental work into the problem of comparing work and heat in the deformation of metallic crystals, where the calorimetric difficulties were less, showed, however, that in the case of copper and aluminum a real discrepancy between work and heat could be shown. Similar results had previously been obtained by Farren and Taylor2 and Hort3 and more or less simultaneously with the author's work by

Jan 1, 1936

Aalde, Kaare. ('40) Gen'I Del., Bisbee. Ariz. Aase, Glenn D., ('40) Univ. of North Dakota. Grand Forks. N. D. Abadesco, Enrique A., ('39) College of Engrg.. Univ. of the Philippines. Manila, P. I. Abbott. John L., ('40) Colorado School of Mines. Golden. Colo. Abdul-Ahad, A., ('39) Montana School of Mines. Residence Hall, Butte. Mont. Abreu, Ovidio M., ('38) Univ. of Nevada, Reno, Nev. Acomb, Allen. ('41) Louisiana State Univ., Box 1970, University. La. Acosta S., Gonzalo. ('40) Univ. of Texas, Univ. Sta., Box 1785. Austin, Tex. Adam, Howard W., ('41) Montana School of Mines. Butte, Mont. Adams, Albert, ('381 New Mexico School of Mines, Socorro. N. M. Adams. Charles W., ('39) Michigan College of Min. & Tech., Houghton, Mich. Adams. H. Travis, ('39) 316 South -5th St., Bur¬bank. Calif. Adams, Jack L., ('39) Univ. of Oklahoma, Nor¬man. Okla. Adams. John W., ('41) Colorado School of Mines, Golden. Colo. Adams. Lewis J.. ('39) 402 Del Mar Blvd., Corpus Christi, Tex. Adams, Rob L., ('40) Agricultural & Mech. Col¬ lege of Texas. Box 600, College Sta., Tex. Adamson. Charles R., ('41) Univ. of Utah, Salt Lake City. Utah.

Jan 1, 1941

A week-long educational program and two-day symposium on applying the fluidizing reactor to the minerals industry drew more than 100 engineers to the University of Arizona at Tucson several weeks ago. The educational program, intended for engineers who will work closely with the reactor, attracted registrants from all sections of the U. S. and Canada. Meeting at the College of Mines on February 23 for a full week of intensive classwork, the engineers ploughed in with enthusiasm. Eight hours daily of lectures and laboratory work were followed by a generous helping of homework supplied by Professor Sigmund L. Smith, who directed the course. The study program was completed on Friday and the following Monday marked the start of a symposium of technical papers covering a wide variety of operations and new ideas.

Jan 4, 1959