Search Documents

By C. R. Van Hise

Introduction.............29 The Three Zones of the Lithosphere ..30 Zone of fracture............31 Zone of flowage............ 31 Factors influencing depth at which flowage occurs.. 32 Zone of combined fracture and flowage.. 33 The Water-Content and Openings in Rocks....36 Condition of rater in the zone of fracture.. 36 The openings in rocks...........38 Size and number of openings..... 40 Ore-deposits derived from zone of fracture..45 The source of underground water......... . 47 The cause of the flowage of underground water..47 Belts of underground circulation.. 51 Upper belt of underground circulation.. 51 Lower belt of underground circulation.. .... .52 Capacity of water for work in the lower belt of underground circulation........... 53 Movementsof water in the lower belt of underground circulation. 54 The preferential use by water of large channels.. 60 Physico-Chemical Principles Controlling the Work of Under ground Waters..........62 Chemical action............63 Underground aqueous solutions..64 The relations of solution and temperature..... 65 The relations of solution and pressure..66 Precipitation........... 67 Precipitation by change in temperature..68 Precipitation by change in pressure..69 Precipitation by reactions between aqueous solutions.. . 69 Precipitation by reactions between liquid solutions and solids. 70 Precipitation by reactions between gases and solutions. and solids............71 The General Geological work of Underground Waters.. . 71 Division of the zone of fracture into a belt of weathering and a belt of cementation............72

Jan 1, 1901

By N. A. Gokcen, J. Chipman

A revised treatment of the authors' published data eliminates the complex relation previously proposed between concentration of silicon and activity coefficient of oxygen in liquid iron. Revised values of the thermodynamic properties of the liquid solution are presented. IN a recent experimental study of the reaction SiO2 (s) = Si+ 2O; Kf, = [% Si] [% O]² [1] the authors' found a substantially constant equilibrium product in liquid iron at 1600°C of 2.8x10-5 They also reported extensive data on the reactions: SiO2 (s) + 2H2 (8) = Si- + 2H2O (g); K'2= [% Si] (H2O/H2 [2] and H, (g) + 0 = H2O (g); K'3 =( H2 O [31 (H2) [%O] From the results on reaction 3 and earlier data of Dastur² on this same reaction in the absence of silicon, they determined the activity coefficient of oxygen, f0, on the basis of the definition K3 = (H2O)/ (H2)f0 [% 0] where K, is the equilibrium constant and f0, is taken as unity in the pure Fe-0 system. Similarly values of fsi were deduced from results on reaction 2. In a more recent study" of analogous reactions in the system Fe-A1-0, it was found impossible to reconcile the results on reaction 3 with Dastur's data; accordingly the latter were ignored and the equilibrium results were extrapolated to find a value of K, at zero concentration of aluminum. This procedure failed to locate the cause of the discrepancy but it did yield reasonable values of activity coefficients. It also avoided introduction of the complex empirical relation between the oxygen activity coefficient and the concentration of the added element. The same type of discrepancy exists for system Fe-Si-0.' In the earlier paper an attempt was made to fit both sets of data by a single curved line (Fig. 6 of ref. l), the form of which is contrary to the theoretical requirement of a finite slope at infinite dilution. In the light of experience on the Fe-A1-0 system the discrepancy must be recognized as one which can be resolved only by more refined measurements. Accordingly Figs. 6 and 10 are retracted. It is pointed out also that until the discrepancy is resolved Figs. 7, 8, and 11 are subject to some uncertainty. Qualitatively the following conclusions still appear valid: 1—The activity coefficient of oxygen is reduced by addition of silicon. 2—In dilute solutions the activity coefficient of silicon increases with its concentration. 3—With respect to equilibrium in reaction 1, the above effects are approximately compensating. The discussion of K'1 in the previous paper requires no revision. It was pointed out that the constancy of the product [% Si] [% 0]² ndicated a compensating effect of the activity coefficients of silicon and oxygen. Therefore, as a very good approximation, K1 = K'1 and the following average values are suggested both for K, and K', at the temperatures 1550°, 1600°, and 1650", respectively, 1.0x10-", 2.8~10-" and 5.5 ~lo-'. Revision of the thermodynamic treatment is necessitated by the recent appearance of new data, based on a combination of combustion and solution calorimetry,' which yields for the heat of formation of low-cristobalite from the elements, the value —209,330 ±250 cal per mol at 25°C. This is about 4000 cal larger than the value previously accepted. The new value for cristobalite is used, together with Kelley's tables of high-temperature heat contents" and entropies and with Korber and Oelsen's' heat of fusion of silicon to obtain the following equation for the standard free energy of cristobalite in the temperature range 1700" to 2000°K: Si (1) + 02 (g) = Si02 (crist.); ?F° = -217,700 + 47.OT [4] The free energy of solution of 0, in liquid iron is:8 O2 (g) = 20 (in Fe); AF° = -55,860 - 1.14T [5] and these two equations are combined to give: Si (1) + 20 = SiO, (crist.); AF° = -161,840 + 48.14T [6] ?F°1873 = -71,700 cal. From the experimental value of K, = 2.8x10-5, Si + 20 = SiO2 (crist.); ?F°1873 = -39,000 cal. [7] The combination of Eqs. 6 and 7 yields the free energy change when liquid silicon dissolves in iron to form the dilute solution of unit activity (1 pct). Si (1) = Si; ?F°1873 = -32,700 cal. [8] The heat effect in this process according to Korber and Oelsen' is an evolution of 28,500 cal per gram

Jan 1, 1954

By R. M. Keeney

Before the outbreak of the war in 1914, the only electric-furnace smelting plant operating on a commercial basis west of the Mississippi River was an electric pig-iron plant in California; rare metal ores were not smelted, concentrates of molybdenum, tungsten, uranium, and vanadium ores being shipped East for reduction. Practically no chrome ore was being mined, and only comparatively small amounts of manganese ore. Today there are two electric smelting plants in California, one in Washington, one in lowa, and four in Colorado; two plants are under construction in California, and one in Montana. Ores of manganese, chromium, molybdenum and tungsten are now smelted in the West, and although uranium and vanadium concentrates are still shipped to the East, they will probably be treated in western plants in a short time. The four electric-furnace plants in Colorado are listed in Table 1. Table 1.—Electric Smelting Plants in Colorado Capacity. Company Location KilowattB PRoductS Tungsten Products Co........... Boulder 800 Ferrotungsten, ferromo- lybdenum. Boulder Tungsten Production Co .. Boulder 400 Ferrotungsten. Ferro Alloy Co.................. Utah Junction 1200 Ferrochrome, ferrotung- sten. Iron Mountain Alloy Co......... Utah Junction 3000 Ferromanganese. Power for all of these plants is supplied by the Colorado Power Co. The plant of the Ferro Alloy Co., at Utah Junction, contains one 750-kw., three-phase furnace, to which power is supplied by three 250-lrw. transformers, connected /Y to give 129 volts on the furnace cables, the transformer ratio being 13,200 to 75 volts. The furnace operates with an actual voltage of 120 volts, and produces about 3 tons of ferrochrome per 24 hr. from 40-per cent. Cr2O3 ore. The furnace consists of a steel shell of circular cross-section, 8 ft. (2.43 m.) in diameter by 7 ft. (2.13 m.) deep, lined with magnesite, and having three vertical carbon electrodes 12 in. (30.48 cm.) in diameter. A 450-kw. furnace, of the same size as the 750-kw. furnace, is also operated on chrome ore. This furnace is three-phase in appearance, but operates electrically as a single-phase furnace. There are three vertical

Jan 1, 1920

In high-volume mining operations, preventive maintenance programs that include standardized replacement wear parts can boost equipment availability and lower unit costs. Meeting the daily production targets depends heavily on keeping equipment working as close to full time as possible. This is the case at one medium-sized western surface coal operation producing approximately 2.7 million t/y (3 million stpy). The mine, located in western Wyoming, removes in excess of 8 million m3 (10.5 million cu yd) of highly abrasive overburden each year. According to the mine superintendent, "Abrasion at this mine is some of the worst I've ever seen. Shovel points can wear out in little more than one shift. Dozer blades some- times last two weeks, but can wear out sooner. And ripper points really take a beating. If we can replace this fast-wearing iron with small pieces that go on quickly, we think that's the way to go."

Jan 3, 1978

By John V. Beall

The Glidden Co., a newcomer to the mining industry, will be putting on stream its Lakehurst mine and concentrator this spring. Ilmenite-bearing placer sands will be mined and concentrated in a spanking new combination gravity, magnetic and high-tension separation plant. Glidden, well known as a paint, chemical and food manufacturer, consumes titanium dioxide as pigment in its paint business. The commodity is produced at the company's Adrian D. Joyce Works in Baltimore from ilmenite purchased in India and Australia, The Lakehurst operation, handily located in Ocean County, N. J., will dampen any deficiencies in quantity or price which might occur from foreign suppliers. This objective is no overnight concoction of The Glidden Co., because the move at Lakehurst was preceded by an attempt to start up in Florida. That project was abandoned when it was found that the titanium dioxide values were largely in rutile-a mineral which does not lend itself readily to the digestion process of the Baltimore chemical plant.

Jan 1, 1962

By James L. Hendrix, Pat Vreeland, Hamilton Vreeland, Marcel F. DeGuire, Peter L. Comanor

A study of the ground area surrounding the Getchell, Nev., gold mine mill tailings was conducted so that a better understanding of the effects of arsenic toxicity on Upper Sonoran vegetation could be obtained. The Getchell area was selected because of the known high values of arsenic currently contained in the tailings waste (1% or higher). Mill wastes as well as the scrubber product As2O3 are contained in the tailings pond. In order to determine the effect of the tailings disposal on the surrounding vegetation, plots and line-transect techniques were employed to obtain plant ecological information on the area surrounding the ponds, and also non-affected control plots. Data for percent ground cover, species frequency, and plant vitality as a function of distance from the tailings ponds were collected. In an attempt to isolate naturally occurring factors for varying plant communities from induced factors derived from the close proximity of the tailings, soil cores were

Jan 1, 1975

By Robert Mehl

IT has been shown that quenched iron of high purity exhibits a Widmanstätten figure much resembling martensite in appearance.1 This figure exhibits a maximum of four directions of the surface traces that characterize it, suggesting that a Fe forms from y Fe in plates parallel to the {111}, octahedral, planes in the y lattice. Because of this, and also because of the general similarity to the structural appearance of martensite and to the Widmanstätten figure obtaining in slowly cooled hypoeutectoid steels it has been suggested2 that the orientation relation-ships obtaining between the y and a phases in pure iron are identical with those demonstrated in martensite3 and in slowly cooled hypoeutectoid steels,4 and indeed that the crystallographic mechanism of formation of a Fe from y Fe is the basic mechanism determining the orientation relation-ships found in both martensite and in slowly cooled hypoeutectoid steels. This paper will present experimental evidence in support of this view.

Jan 1, 1934

By William M. Kester

INTRODUCTION The Coal Research Bureau of the School of Mines at West Virginia University is presently conducting laboratory-scale tests to determine the technical feasibility of beneficiating pulverized coal and coal fines with high-intensity electromagnetic fields. Interest in magnetic processes for cleaning fine coals was stimulated by results obtained by Yurovsky, et a1 in 1958.1 This work, while not new in concept,2,3 indicated that pulverized coal which had been thermally treated in a rotary drum in the presence of superheated steam and air underwent thermo- chemical reactions. Films of the ferromagnetic minerals magnetite (Fe2O3), hematite (Fe3O4), and pyrrhotite (FeS[3]) were reported to be formed on the surfaces of the pyrite grains associated with fine coal during the foregoing treatment at temperatures ranging from 120 to 360°C. After thermal treatment the coal was magnetically separated in an experimental magnetic device having a field strength of 10,000 oersteds.

Jan 5, 1965

By Paul C. Merritt

For more than 100 years, British Columbia has been considered a mountainous mining province, rich with potential but relatively poor in actual production. Times have changed. Today, Japanese interests and money have altered the difficult, if not once impossible, economic conditions and market factors which until recently precluded any great growth of the British Columbia mineral industry. The mining boom now underway in British Columbia has carried the total value of mineral production in the Province to a record height in 1962 as it rang up a 27% increase over that of 1961. Breaking the $200 million barrier for the first time, total value of British Columbia's mineral output reached $229- 276,385. Of this amount, metals accounted for 70%; industrial minerals, 6 %; structural materials, 9 %; and fuels, 15%. The substantial increase is attributed to the record production of copper, iron, asbestos, natural gas and petroleum, in addition to the continuing high production rate and favorable prices of other mineral commodities.

Jan 12, 1963

By E. P. Peleider

DIAMOND drill research work was initiated at the School of Mines, University of Minnesota, in late 1949. The Drilling Symposium held in Duluth that spring highlighted the problem of high cost and core recovery and the need for controlled testing. An advisory committee made up of informed representatives of both mining companies and drilling companies was formed to suggest and advise on a program of drill research. A Hy-Mac hydraulic drill unit, see Fig. 1, especially designed for experimental testing, was obtained for this work by the School of Mines through the courtesy of the Carboloy Co. It is an extremely flexible unit, capable of exerting a forward thrust of about 1750 lb and turning at speeds from 650 to 2200 rpm. The feed arrangement is so designed that the advance can be set either at a constant rate or permitted to vary at a fixed Pressure, see Fig. 2. The

Jan 1, 1953

By E. P. Peleider

DIAMOND drill research work was initiated at the School of Mines, University of Minnesota, in late 1949. The Drilling Symposium held in Duluth that spring highlighted the problem of high cost and core recovery and the need for controlled testing. An advisory committee made up of informed representatives of both mining companies and drilling companies was formed to suggest and advise on a program of drill research. A Hy-Mac hydraulic drill unit, see Fig. 1, especially designed for experimental testing, was obtained for this work by the School of Mines through the courtesy of the Carboloy Co. It is an extremely flexible unit, capable of exerting a forward thrust of about 1750 lb and turning at speeds from 650 to 2200 rpm. The feed arrangement is so designed that the advance can be set either at a constant rate or permitted to vary at a fixed Pressure, see Fig. 2. The

Jan 1, 1953

By E. P. Pfleider

DIAMOND drill research work was initiated at the School of Mines, University of Minnesota, in late 1949. The Drilling Symposium held in Duluth that spring highlighted the problem of high cost and core recovery and the need for controlled testing. An advisory committee made up of informed representatives of both mining companies and drilling companies was formed to suggest and advise on a program of drill research. A Hy-Mac hydraulic drill unit, see Fig. 1, especially designed for experimental testing, was obtained for this work by the School of Mines through the courtesy of the Carboloy Co. It is an extremely flexible unit, capable of exerting a forward thrust of about 1750 lb and turning at speeds from 650 to 2200 rpm. The feed arrangement is so designed that the advance can be set either at a constant rate or permitted to vary at a fixed pressure, see Fig. 2. The

Jan 1, 1952

By A. F. Crawley

The densities of some liquid Pb-Sb alloys up to 11 wt pct Sb and Pb-Sb-& alloys up to 10 pct Sb/10 pct Sh have been determined by a pycnometric technique over a temperature range of about 130°C above their melting points. The data given are accurate within 0.05 pct. Density is shown to vary linearly with temperature , and equations relating these quantities have been formulated. Molar volumes calculated from the density data indicate that volumetric deviations from ideal mixing are undetectable within the limits of experimental error. A continuing research program into some fundamental physical properties of liquid metals is being pursued at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. This work has received support from the Canadian Zinc and Lead Research Committee in cooperation with the International Lead and Zinc Research Organization. This paper, which reports some density data for Pb-Sb and Pb-Sb-Sn alloys, follows previous work from this laboratory on lead, tin, and Pb-Sn alloys.' Of previous data from others, Greenaway2 and Sato and Munakata3 have reported results on Pb-Sb alloys. No previous work has been published on the ternary Pb-Sb-Sn alloys, reported here. EXPERIMENTAL METHOD Densities were measured by a pycnometric technique which has been described in detail and appraised for accuracy in earlier Mines Branch reports.475 Fig. 1 shows the densitometer with the pycnometer in position for a run. The pycnometer is also shown in some detail. The pycnometer of dense, high-purity graphite, about 14 cu cm in volume, was carefully machined to a uniform, smooth finish. The height was measured by a depth micrometer and the diameter by fitting precision gage blocks between steel balls.' In each case several readings were taken, and the final results were considered accurate within 0.01 pct. The resulting volumetric uncertainty together with small inaccuracies in the coefficients of linear expansion of graphite lead to a maximum systematic uncertainty in the method of ±0.03 pct. As shown in Fig. 1, the pycnometer lid is a threaded cap. Thus, the charge, a cylinder of the alloy, can easily be inserted and the solidified metal can readily be removed after a run. The dimensions of the cylindrical charge are chosen to ensure that, once molten, the metal will not only fill the pycnometer completely but will discharge an excess into the excess-metal float chamber. AS the temperature is increased above the melting point, the volume of metal in the excess chamber increases until the system has equilibrated at the desired temperature. At this point, the excess chamber is moved to one side by twisting the shaft F, leaving a fixed volume of liquid metal in the pycnometer. This volume of fluid is readily calculated using measured coefficients of linear expansion of the graphite which expands anisotropically. The associated weight of fluid is determined as the weight of the solidified metal removed after the furnace has cooled down. Alloys were prepared from 99.997 pct Pb, 99.999 pct Sn, and 99.999 pct Sb, being melted by an electric furnace in a graphite crucible and poured into graphite molds. Several density specimens of the same nominal size were machined from each ingot, and, by comparing specimen weights, relative differences in specimen composition resulting from segregation in the ingots could be detected. In this way, segregation was found to have occurred in Pb-Sb alloys at compositions beyond the eutectic (11.2 pct Sb) and this

Jan 1, 1969

By J. S. Brown, A. G. Guy

With the exception of the work of Tammann and Hartmann,1 no published information has been found on the structural changes produced in eutectic structures as the result of heating following plastic deformation. In part this lack of information may be due to the fact that many eutectic structures contain an intermetallic compound as a prominent phase, and as a consequence have been considered to be unworkable. For example, Tammann and Hartmann were able to obtain useful data only on those alloys that they could greatly reduce in thickness by cold rolling. This restriction placed on the investigation of alloys containing intermetallic compounds has been largely removed by the work of Savitskii2 which showed that large deformations of such alloys can be produced by relatively slow compression at temperatures near the melting range. It was possible, therefore, to carry out the present work on a range of binary eutectics including one composed of two intermetallic compounds. The essential results obtained on the alloy systems studied are illustrated by the Pb-Mg eutectic containing 33.2 pct Mg, Fig 1. The cast structure, Fig la, was obtained by melting together magnesium of 99.8 pct purity and chemically pure test lead, casting into a heated, small steel mold, and furnace cooling in the mold from about the eutectic temperature. The fairly coarse eutectic structure thus obtained was too brittle to work at room temperature without cracking. Fig 16 shows the worked structure obtained by compressing a 1/2-in. cube 70 pct in about 15 sec at 550°F and then water quenching. The pronounced changes in the distribution of the two phases produced by heating the worked alloy at 850°F for 1 hr are shown in Fig lc. Recrystallization of both phases appears to have taken place, and the mechanical properties of the cast alloy must have been significantly changed by the working and heat treatment. Similar results were obtained with the Mg-59.5 pet Bi, Mg-36.4 pet Sn, Mg-65.4 pet Cu, and Bi-40 pet Cd eutectics, only the last of which could be worked at room temperature. Tammann and Hartmann reported a thickening and shortening of the needles of the eutectics which they heated about 10°C below the melting range for 1 hr after drastic cold rolling. They found the following eutectics, given the indicated amounts of reduc- tion, to have a granular structure after heat treatment: Sn-9 pet Zn (98 pet); Cd-82.5 pet Pb (60 pet); and Bi-43.5 pet Pb (90 pet). On the other hand the alloy Al-11.7 pet Si (60 pet) showed no change after heating. Tammann and Hartmann observed a distinct shrinking of the needles in unworked eutectics subjected to heat-treatment. In the present work inappreciable change in the eutectic structure was found on heating undeformed alloys. In summary, it appears that eutectic structures can be recrystallized into a "spheroidized" condition by heating near the eutectic temperature after severe deformation. If the eutectic contains one or more brittle phases the necessary deformation can be accomplished by pressing at high temperatures. It is reasonable to expect that this tendency towards equiaxed grains from the plate- or needle-like eutectic structure should be general since the energy relations and mode of growth in recrystallization are so different from those that hold for eutectic crystallization. References 1. G. Tammann and H. Hartmann: Ztsch. Melallkunde (1937) 29, 141-144. 2. E. M. Savitskii: Doklady Akad. Nauk S.S.S.R. (1940) 62, 349-351. Abstr. in Melal Prog. (July, 1949) 56, 126, 128.

Jan 1, 1950

By Burt C. Mariacher

To note that environmental considerations had a major im¬pact on the minerals processing industry in 1971 would be something less than a profound observation. The degree of its importance was demonstrated by MBD when it established the Environmental Committee as a new unit committee within the Division to achieve greater participation in exchange of information relating to the technologies and problems involved. It is appropriate and necessary to devote special attention to this timely aspect of minerals processing, as its influence penetrates the research, engineering and operations of almost all unit technologies that comprise minerals processing. The pollution abatement aspect of this industry has been such a dominant factor in recent years there is reason to wonder whether progress in unrelated technologies has been curtailed. Perhaps so, to some degree, but unit committee reviews presented in this article suggest rather that it would appear to have served as a catalyst for accelerated progress in development of new methods and improvement in more conventional ones. Present concepts regarding primary metal or mineral recovery and by-product potential may change considerably as a result of improved technology in waste product treatment.

Jan 2, 1972

By V. C. Wansbrough

A LUCID, thorough and powerful review of the impact of your tax laws on mining operations has already been presented by Granville S. Borden*. He has brought into focus and relief the pressure-points at which the shoe pinches most, has suggested some remedial measures, and enunciated much sound doctrine about the interrelationship and interplay of taxation policy and mining activity. Under the heading "What Every Lawmaker Should Know", he laid down the fundamental proposition that "the magnitude of our mineral resources varies inversely with the magnitude of the taxes levied upon them." With this, as with his other major premises, all mining men must be in hearty concurrence. There can be no doubt that a flourishing and expansive future for the mining industry in this country, in Canada, or anywhere else will depend on the thoroughness with .which these fundamental propositions are grasped by legislators, by national policy-makers and by public opinion at large.

Jan 1, 1950

By D. Turnbull, R. E. Cech

FISHER, Hollomon, and Turnbull have developed a theory for the nucleation of martensite. They first tested the theory on Fe-C alloys and low alloy steels. The major factor influencing nucleation of martensite was considered to be statistical composition fluctuations occurring in small regions at high temperature and frozen-in on quenching. These local regions of varying size and composition serve as nucleation centers. They become supercritical, one by one, as temperature is progressively lowered, resulting in temperature-dependent or athermal transformation. Fisher next applied nucleation theory to substi-tutional solid solution alloys. Detailed predictions were made for Fe-Ni alloys because of the availability of free energy data on this system. It was shown that composition fluctuations that were significant energy-wise did not occur, and nucleation frequencies could be calculated from average properties of the system. Nucleation was predicted to occur as time-dependent and having the functional relationship to give a C curve of nucleation frequency vs temperature. The analysis further predicted that the nucleation frequency was extremely sensitive to composition. Experimentally, it would be found that the transformation in some compositions is so slow that measurable amounts will not form in a reasonable length of time. With other compositions, only slightly different, the nucleation frequency becomes so great that the material becomes transformed while still distant in temperature from the maximum nucleation frequency. On quenching an alloy of such composition, the observed transformation kinetics would be similar to those found in Fe-C alloys. Cech and Hollomon repeated experiments of Kurdjumov n which the kinetics of transformation were similar to those predicted by Fisher for Fe-Ni alloys. The alloy studied in this investigation contained 73.3 pct Fe, 23.0 pct Ni, and 3.7 pct Mn. Fisher,' using an idealized model for the extent of transformation as a function of the number of martensite crystals per grain of parent phase, derived nucleation frequencies from the transformation curves of Cech and Hollomon. Complicating influences such as coupling effects between grains in the polycrystalline specimens were neglected. Nevertheless, excellent agreement was found between the theoretically and experimentally derived nucleation frequencies. These experiments, however, could not provide a critical test of the theory. Experimental nucleation frequencies could vary widely from those calculated, depending upon the extent of deviation from ideal partitioning and the extent of coupling effects. Further, since the compositions of material theoretically analyzed and experimentally determined were different, the free energy changes involved in the experimental work could only be estimated. Also, the effect of heterogeneities on the transformation kinetics was not considered. For these reasons, it was decided that experiments designed to test the validity of the Fisher analysis must be conducted on binary Fe-Ni alloys, which were the ones considered theoretically by Fisher. The martensite transformation in Fe-Ni alloys has been the subject of considerable study. Machlin and Cohen have shown that transformation proceeds in a manner quite unlike that in any other ferrous alloy system. They found that single crystals would transform to a large extent in a single burst. In large grain polycrystalline specimens, frequently more than one grain and sometimes the whole specimen would transform at the same instant in this manner. Results on filings indicated that different particles would undergo the burst transformation at widely different temperatures. These results support the conclusion that the transformation behavior could not be described by a single nucleation frequency as would be the case if the nucleation were homogeneous. It appeared that further work was necessary to define the factors responsible for burst-type transformation, so that the conditions could be altered to favor homogeneous nucleation of martensite if such could be accomplished. This report summarizes the results of some experiments conducted with powdered Fe-Ni alloys for this purpose and the re-

Jan 1, 1957

By John Wulff, David A. Stevenson

The rates of solution of copper, nickel, and three copper-nickel alloys in liquid lead were studied at 527° and 727°C under dynamic conditions. The relative velocity at the solid-liquid interface was varied from 8.65 to 125 cm per sec. Analysis of the data for the pure metals indicates that the solution rate is transport corztrolled at lower velocities, but a transition to mixed control occurs at higher velocities, higher temperatures, and higher percent saturation. 1 HE present work concerns the effect of relative velocity at a solid-liquid interface on the dissolution kinetics of pure solid materials in liquid metals. This general problem is of interest in electrode kinetics, in electrolytic processes, and more recently in the field of liquid metal corrosion. Considerable work has been done on dissolution kinetics in aqueous environments because of the obvious importance to electrolytic processes.1,2 In purely metallic systems investigation has been more limited. There are, of course, extensive data from loop tests which are used in an engineering evaluation of liq- uid metal corrosion. Here, however, the dissolution process is complicated by several interdependent processes. In general, one of two factors is considered to be rate limiting in the dissolution process: the transport of material from the solid-liquid interface into the bulk liquid, or an activation process directly at the interface. A number of studies of the dissolution rates of solid metals in liquid metals under static conditions have been published.3- Since the attendant hydrodynamic conditions imposed by thermal gradient convection and concentration gradient convection are difficult to analyze, it is doubtful if a clear interpretation of the experimental findings of these papers in terms of the mechanism involved in the dissolution process can be made. A clearer picture of the dissolution process is provided by

Jan 1, 1962

By Dale A. Vaughan, Oliver M. Stewart, Charles M. Schwartz

A. U. Seybolt (General Electric Research Laboratory)—The authors should be commended for adding some important information to our knowledge of the solubility of interstitial elements in metals. It is becoming increasingly evident that the effect of even traces of such elements have very far-reaching effects upon the mechanical properties of the body centered cubic metals. Those who have worked in this area know that the accurate determination of the small solid solubility limits in systems of the type reported by the authors is a quite difficult task, and it is therefore not surprising that frequently the results of different workers are not in agreement. It is instructive, and usually helpful, to plot the solubility results on log weight or atomic percent -1/T coordinates to find out if a straight line is obtained. A straight line is expected because in systems displaying solubilities of the order of 1 to 3 at. pet or less, Henry's law is usually obeyed—or at least well enough obeyed so that the deviation from linearity is not very appreciable. If Henry's law is obeyed, one canthen use the Van't Hoff Equation in the form In N = ?H/RT + C, where N is mole fraction, at. pet, or wt pet for small values, and AH is the partial molal heat of solution of the solute. R and T have the usual significance, and C is an integration constant. If one plots the reported nitrogen solubility values as indicated above, the three points fall reasonably well on a straight line. The oxygen values for the two upper temperatures fall very closely to the nitrogen values as shown in the authors' Fig. 15. However, the value at 500°C departs widely from the straight line established by the data at 1500" and 1000°C. It is, of course, true that one cannot place too much emphasis on the significance of a line established by only three points, but in the absence of reasons for anticipating deviations, data exhibiting wide departures from linearity should at least be examined closely. Fig. 16 shows the log at. pct -1/T plots for the authors Ta-O and Ta-Ndata including a solid circle point at 500°C and 1.8 at. pet for Ta-O, which is simply extrapolated from the two higher temperature points. In addition, the data of R. P. Elliott9 for Nb-O are shown. These points were picked off his curve and are not very exact, but as can be seen they line up well on a straight line. It is interesting, and probably significant, that the slope of Elliott's results is not far from those of Vaughn, et al. This is probably to be expected because one would anticipate that the partial molal heats of solution of oxyten in these two very similar metals should be not too far apart. AH for Ta-O is about -1900 cal per mol, while for Nb-O it is near -2300 cal per mol. Hence, this lends some support to the thesis that the point at 500°C for Ta-O is much too high. The data of Gebhardt and Preisedanz10 are also plotted, and it is seen that their data while lying on a linear plot, have an appreciably steeper slope. The possible reasons for this will not be discussed here except to point out that their pressure-composition data show anomalies which suggest that they may have been dealing with a different equilibrium from that being discussed. There is another consideration which would also suggest that the solubility at 500°C is lower than shown. The solubility values were obtained by the classic method of first establishing a lattice parameter-composition curve. This the authors did, and there is probably little doubt that it is quite accurate. Such a plot is generally almost error-free because it has a self-correcting feature in that any deviation from linearity makes a data point immediately suspect, and subject to confirmation. Unfortunately, this is not true with respect to the actual solubility values. These are obtained ordinarily by taking an alloy containing more solute than is soluble at some temperature and then thermally

Jan 1, 1962

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 *ABBOTT, CHARLES W., Min. Engr. Pioche, Nev. ?08 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94 *AOTT, ROBERT R., Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 || ARAHAMS, ALEXANDER I., Student.. .67 E. 93rd St., New York, N. Y. '13

Jan 1, 1917