Search Documents

By U. Oko

The cause and the effect of disposing of tailings water from sulfide ore milling operation were examined. Dissolved metallic ions as well as dissolved sulfur-oxygen compounds (polythionates) can prove injurious to life in water streams. Polythionates originate in alkaline flotation circuits and may cause a severe drop in the pH of stream waters. It is proposed that a suitable "aging" period be allotted to tailings water to ensure complete conversion of polythionates to sulfate prior to neutralization and clarification treatment. Discharging alkaline solid-free tailings water without aging will cause downstream acidification. Artificial oxidation of tailings water can be economical only if the concentration of thiosulfate in solution is low. When the concentration is high, it is possible to reduce the concentration greatly by first acidifying the solution, because at a pH below 4 thiosulfate in water reacts to produce a precipitate of elemental sulfur and higher order polythionates. The residual polythionates can then be oxidized at great savings by natural aging or by chemicals such as ozone, chlorine, or peroxide. Chlorine may be an economical reagent for converting polythionates to sulfuric acid but the residual organo-chlorinated compounds can prove to be toxic to aquatic life. Ozone and hydrogen peroxide which do not leave a residue are preferred oxidizers.

Jan 1, 1976

By N. S. Stoloff, J. N. Mushovic

Age hardening response of a Mg-Th-Zr alloy has been studied at temperatures in the range 60° to 450°C. Transmission microscopy revealed clustering of thorium atoms at low aging temperatures, supporting a previous report of GP zone formation. Peak strengthening, which is observed at 325°C, is due to the formation of a coherent, ordered, DO19 type superlattice structure, of Hobable composition Mg3Th, as plates parallel to the matrix prism planes. These plates later reveal a Laves phase structure of composition Mg2Th. The equilibrium Mg4Th phase begins to precipitate in two different forms at an early stage, competitively with the Mg2Th plates. RECENT work on the Mg-Th system indicated that, unlike most magnesium-base alloys, complex precipitation phenomena may be occurring. The partial phase diagram of the Mg-Th system indicates that an equilibrium phase, Mg5Th, is the sole intermediate phase.' sturkey,' however, has reported, using X-ray and electron diffraction techniques, that a metastable fcc Laves phase, Mg2Th, precedes the formation of the equilibrium compound, which he identified as closer in composition to Mg4Th. Murakami et al.3 reported that the equilibrium phase precipitates preferentially on grain boundaries and dislocations in a Mg-1.7 wt pct Th alloy; Kent and Kelly4 aged a more dilute alloy, Mg-0.5 wt pct Th, for 4 days at 220°C and found similar results. In addition, they reported that a platelike phase with a structure close to that of the magnesium matrix forms perpendicular to the basal plane and is probably ordered. Research on a Mg-4 wt pct Th alloy by electrical resistance measurements and transmission electron microscopy has suggested that GP zones may form at low aging temperatures.3 However, the electron micrographs purporting to show this phenomenon were not conclusive. In view of the fragmentary evidence concerning the nature of the precipitation processes in the various Mg-Th alloys, an aging study was undertaken to clarify the characteristics of the various precipitates which form and to correlate the mechanical properties of the system with the direct precipitate-dislocation interactions. The latter results are presented elsewhere.' The purpose of this paper is, therefore, to discuss the precipitation sequence in this system. EXPERIMENTAL PROCEDURE Sheet stock (0.060 and 0.010 in. thick) of a commercial Mg-3.93 wt pct Th-0.42 wt pct Zr alloy (designated HK3lA) similar to that studied by sturkey2 was supplied through the courtesy of Dr. S. L. Couling of Dow Metal Products Co. Zirconium does not enter into any precipitation reactions,' but is present primarily as a grain refiner. The alloy was chill cast, warm rolled to 0.090 in. thick stock, and then finally reduced by a combination of hot and cold rolling. The alloy chemistry is given in Table I. This material was solution treated at 580°C for 4 hr in a dry CO2 atmosphere, and then water quenched. Material in this condition was fairly clear of precipitate particles and was fully recrystallized. Aging at temperatures less than 200°C was accomplished by immersing the alloy in a silicone oil bath; for higher temperatures, aging was done in a salt pot. Age hardening treatments were conducted at 60°, 80°, 105°, 135°, 160°, 250°, 325°, 350°, and 450°C for times ranging from 5 min to 400 hr. Hardness tests were performed on chemically polished 0.060-in.-thick blanks of solution treated material which were aged at the various temperatures for increasing lengths of time. For aging temperatures above 150°C the Rockwell Superficial 30T scale was employed, while samples hardened at temperatures below 150°C were monitored with the 45T scale. Each data point consists of at least three separate readings. Yield stresses also were measured at room temperature on both 0.060 and 0.010 in. sheet specimens aged at 325°C. The aged foils were thinned by the window method in a solution of 80 pct absolute alcohol and 20 pct concentrated perchloric acid (70 pct) maintained at 0°C. A stainless steel cathode was used and the applied voltage was 10 to 15 v. Thinned samples were rinsed in distilled water and pure methanol. After the me-thanol rinse the thin foils were quickly dried between filter paper. Foils prepared by the above method were examined in a Hitachi HU11B electron microscope operating at 100 kv. RESULTS A) Hardness. The hardness data are depicted in Figs. 1 and 2. Peak strengthening occurs at 325°C after aging about 6 min, see Fig. 1. Significant strengthening is achieved also at 350°C, but aging at 450°C produces only softening. The stepped curve at 250°C indicates that a complicated precipitation process may be occurring at that temperature. Fig. 2 suggests that at least two hardening mechanisms exist since the lowest temperature hardness peaks are displaced to the left of the peaks obtained at 135° and 105°C. A great deal of scatter is observed at long times in all cases due to magnesium surface degradation caused by the silicone oil bath. B) Identification of the Strengthening Precipitates. The structure formed atlowagingtemperatures (c10O°C) was not clearly resolvable by transmission microscopy. The only bright-field evidence for a change in structure was a mottled appearance which could be observed at extinction contours, as shown in Fig. 3(a), and the disappearance of this effect when dislocations produced under the influence of the electron beam passed through the matrix, as noted in

Jan 1, 1970

By D. A. Rice, M. C. Fuerstenau

Flotation data indicate that sulfonate and amine adsorb physically on manganese oxide; oleate also adsorbs physically if the zero point of charge is sufficiently high. Chemisorption of oleate occurs on pyrolusite between pH 8 and 9, and possible mechan- isms of collector adsorption involving metal ion hydrolysis are discussed. The flotation characteristics of most metal oxides1-15 have been examined with standard collectors such as fatty acids and sulfonates. From these studies it would appear as though electrical phenomena are important when shorte r-chained collectors are involved. For example, Iwasaki, Cooke, and Choi9 have shown that dodecyl amine and dodecyl sulfate float iron oxide above and below the zero point of charge, respectively. In another system, D.W. Fuerstenau and Modi10 have shown that dodecyl sulfate, dodecyl

Jan 1, 1969

By W. M. Courtis

. There seems to be a well-established belief that there is an indescribable something in the appearance of gold-quartz not to be learned from books, that enables those who are fortunate enough to have acquired the power to recognize this characteristic, to pronounce at once that a certain quartz will or will not pay. The stronger this claim is made, the more certain is the claimant to be one of the self-styled practical miners. After several years spent among the gold-mines of California with practical and professional gold-miners, I have come to the conclusion that very few care to risk an opinion on a piece of quartz until some of it has been "horned out." Nevertheless, there is what the miners call a " kindly " appearance, that is more often followed by good results than is a vitreous, water-wet-looking quartz. A dark, resinous quartz seems to be most in favor, but there are so many exceptions that even quartz as " white as a hound's tooth " produces gold in some mines.. The ribbon-quartz, a laminated variety, separated by thin talc or chlorite partings, has a well-known good name. The slides of rich quartz specimens show that this parallelism is a microscopical characteristic of the only macroscopical distinction that, as a rule, these quartzes show. This is shown by Nos. 12 and 13, photographs of the richest quartz, that averaged $65 per pound. It is noticeable, also, in Nos. 7 and 9, and others. Dr. Hensoldt, of Columbia College, who prepared, excellently, a large number of my slides, and whom I have to thank for descriptions and suggestions, says of Nos. 12 and 13: "This variety of quartz differs considerably, microscopically, from the others of your locality, and is, in more than one respect, remarkable. Like the

Jan 1, 1890

By H. R. Froning, R. O. Leach

In wertability alteration flooding, a chemical agent is rnoved through a reservoir by the flood water to increase oil recovery by decreasing the degree of wetting of the rock by the oil. Substantial amounts of the chemical may be lost during movement through the reservoir. The extent of the loss, and therefore the economics of the process, depends in some cases on factors which are difficult to reproduce in the laboratory. Therefore, a short-duration, low-cost field test method is needed to permit evaluation of chemical requirements under actual field conditions. This paper describes a small scale rest conducted at a single well for measuring chemical requirements, thereby giving a more reliable evaluation of this important factor in the applicability and economics of the process. In the rest a small wafer slug containing the chemical agent and a nonadsorbed tracer is displaced into the reservoir by a known volume of wafer. The well is then placed on producrion. Chemical loss per barrel of pore volume contacted is calculated from [he fractional recoveries of the agent tested and the nonadsorbed tracer. The method has been used to determine within the actual reservoirs the chemical requirements for both a sandstone and a dolomite reservoir. Several chemical agents are potentially available for wettability alteration flooding, although none is universally applicable. For some applications of the method, chemical costs per barrel of additional oil recovered can be substantially less than one dollar. INTRODUCTION Wettability alteration flooding provides a means of increasing oil recovery from reservoirs by decreasing the degree of wetting of the rock by the oil and increasing the displacement efficiency of the flood water. Earlier studies demonstrated a relationship between oil recovery during waterflooding and the degree of wetting of a rock surface by an oil. The application of wettability alteration flooding to the Harrisburg field of Nebraska provided a field test' of this recovery process. Subsequently, additional laboratory and field tests have developed additional procedures for evaluating wettability alteration flooding, and have indicated where the process may be applicable. Applicability of this process to specific reservoirs is determined by a progression of tests to determine sus- ceptibility of the reservoir to alteration of its wettability, to indicate the degree of recovery improvement and to estimate the amount of chemical required to process the reservoir. The economics of applying improved oil recovery processes depends not only upon the degree of improvement in oil recovery achievable by the process but also upon the process costs and the timing of the income and the investment. Emphasis in this paper is on the expenditure aspects of the process. The work reported in this paper indicates that the chemical investments required for wettability alteration flooding are substantial. For evaluating the economics of a potential flooding application it is imperative that a sound estimate of the chemical requirements be made for the reservoir. Generally, true reservoir conditions are not adequately simulated in laboratory chemical propagation tests. Because of wide well spacings, many years might be required to obtain chemical propagation data from conventional pilots or inter-well tests. Consequently, n short-duration, low-cost method is needed to determine chemical requirements in the field. The potential applicability of wettability alteration flooding is discussed, as well as the economics of wettability alteration with respect to the inherent and imposed restrictions on the timing of income and investments. DETERMINATION OF CHEMICAL REQUIREMENTS In the process of moving a chemical bank through reservoir rock, some of the chemical agent lags too far behind the flood front to be effective or is otherwise lost to the reservoir system. The extent to which these losses occur overshadows the reductions in chemical concentration due to diffusion and to mixing with the reservoir fluids. Experience indicates that almost without exception, chemicals which induce a wetting change undergo either sorption reactions or chemical reactions with mineral constituents of the pore surfaces. Other reactions may occur between the added chemical and the reservoir oil and water. Even in limiting consideration to reactions of the relatively inexpensive inorganic salts, bases and acids, the reactions may be exceedingly complex. Reservoir pore surfaces consist of more than silica in sandstone reservoirs, and more than calcite or dolomite in carbonate reservoirs. Many mineral species are present, each exhibiting specific tendencies to react with an injected chemical. The reactions which occur can consume enough of the agent to have an important effect on economics. These reactions can cause a change in pH of the chemical bank, or may remove some of the active chemical by precipitation, adsorption or reaction to form a new chemical which may or may not be effective in

By Samuel S. Wyer

The following description of methods for conducting gas-producer tests is probably the first attempt to give the subject an analytical, thorough and comprehensive treatment. In some cases where tests have been made, the methods have been so unsystematic and ambiguous that it has been impossible to secure comparable results. To eliminate this difficulty, the following provisional code of gas-producer tests— which has some resemblance to the code of boiler-trials of the American Society of MechanicalEngineers—has been developed. The primary object in testing a gas-producer is to determine whether the producer is working satisfactorily or, what is the same thing, to see if the efficiency is as high as it should be with the type of producer in question; and also to find out if the composition of the resulting gas is adapted to the work it has to do. In order that the test shall be of any value, it must be thorough and comprehensive, and must be conducted with skill and care. When so conducted, the test will reveal the economy of the'producer; and, by making suitable changes, the efficiency will often be increased very much. As a result of the tests made by Jenkins,' the efficiency was raised from 56.2

Jan 1, 1906

By E. S. Fisher

GRAIN coarsening implies a discontinuous type of grain growth during which a few grains in a fine grained recrystallized matrix grow to large grain sizes at the expense of the matrix. Studies of this phenomenon in various metals1,2 indicate that grain coarsening may result when continuous grain growth in a fine grained matrix is inhibited by either a dispersion of very fine inclusions or by a strong texture. In the former case a period of annealing time exists prior to grain coarsening during which grain growth inhibition is gradually de- creased by dissolution or coalescence of the dispersed inclusions. This mechanism can be made to occur in uranium during anneals at high a phase temperatures. ' A study of some of the factors influencing the kinetics of grain coarsening and the coarse grain sizes in a uranium has led to a method for preparing a uranium single crystals. Previously such single crystals containing considerable substructure were prepared at this laboratory by a phase change method, similar to that described by Cahn.3 Attempts to prepare more perfect single crystals by strain-anneal techniques were unsuccessful. Cahn3- as reported his attempts to apply such techniques to uranium. He proposed that the failure of strain-anneal techniques is basically due to the many twins which

Jan 1, 1958

By R. Schuhmann

PROBLEMS in expressing, interpreting, and using size-distribution data recur in many phases of mineral dressing; therefore it is desirable that size analyses be expressed in such a form, either numerically or graphically, that comparisons can be made readily. The size distribution of comminuted material is a result of a specific physical operation on the material and therefore should be governed by some definite physical principle, or cause-effect relation. Although this principle has not been discovered, it has been found that the size distribution of comminuted, homogeneous solids may be expressed by relatively simple mathematical equations. Two equations in particular, proposed by Gaudin1 and by Rosin and Rammler,2 respectively, have stood out, both having wide demonstrated ranges of application. The form and the method of application of the two appear almost irreconcilably different on the surface, but, as will be shown, they are asymptotic in the fine sizes when expressed in the same units. This paper gives the results of a further study of the Gaudin and Rosin-Rammler relations, made with the object of developing a form of size-distribution equation that will be more usable and more significant-particularly in comminution studies, both for interpreting the nature of size distribution and for evaluating surface. The work is summarized in the following: I. An equation relating cumulative per cent finer to particle size in the fine sizes is derived from Gaudin's original equation. That equation relates weight per cent retained on one size and through the next larger size in a geometric series of sizes to size (of the retaining screen, for example). 2. Comparisons with Gaudin's equation and with the Rosin-Rammler equation show that the cumulative equation applies to the fine sizes of all size distributions that fit either of these earlier relations, and, furthermore, has some advantages over each. 3. A simple graphical method of surface calculation based on the cumulative-equation plot is evolved and illustrated. 4. Additional confirmation of the cumulative equation was obtained in the more severe test of sizing down to the limit of a sedimentation balance a sample of jaw-crushed quartz. The equation was closely followed over a 20o-fold range in size, from approximately 0.4 mm. (35 mesh) down to 0.0023 mm. (2.3 microns), the lower limit of the size analysis made. There is no indication that the equation will not hold further to well below 2.3 microns. 5. Calculations of the surface produced in the jaw-crushing test mentioned above showed that at least 8o per cent of the total new surface was on particles finer than 35 mesh (about ½ 5 of the crusher setting). The minus 35-mesh portion was only

Jan 1, 1940

By Franz Posepny

CONTENTS. Introduction. Part I. General Facts And Theories. [ ]

Jan 1, 1902

By James K. Stanley

WHEN a plastically deformed metal is heated to a certain temperature, it undergoes a complete change in microstructure, the consequence of which is a marked alteration of mechanical properties such as hardness, strength and ductility. This change in microstructure occurs by recrystallization and is a process involving the formation and growth of strain-free nuclei in the deformed matrix. These nuclei continue to form with time and grow until a new grain structure replaces the cold-worked structure. The formation of the nuclei in the deformed sheet of 1 per cent silicon ferrite is illustrated in Fig. 1. If a recrystallization is conducted isothermally, a measurement of the fraction of the matrix recrystallized plotted against time leads to an isothermal recrystallization curve, first established in 1942.1 Such recrystallization curves are shown in Fig. 4. These curves show that the recrystallization of a cold-worked metal is best considered as a rate process rather than a time independent process such as is suggested by the improperly named and misleading recrystallization diagrams involving deformation, temperature, and grain size. 2-5 Any study of the rate of recrystallization resolves itself into a study of the component rates of nucleation and growth. The previous paper' provided an account of the determination of the rates of nucleation; N, the number of nuclei formed per unit time per unit of unrecrystallized area, and growth, G, the radial growth in unit time, in the recrystallization of silicon ferrite (1 per cent Si). A method was developed to furnish experimental data for evaluating the effect of the recrystallization variables on N and G. The mathematical analysis for the derivation of the isothermal recrystallization curve was developed for a two-dimensional case (in thin sheets where the diameter of the recrystallized grain is greater than the sheet thickness). The present paper is a continuation of the study of recrystallization of 1 per cent silicon ferrite begun in 1942.1 In this work the effect of the factors deformation, temperature, grain size, composition, and recovery is studied with respect to the rates of nucleation and growth. At the same time it is shown how the cooperation of N and G affects the isothermal recrystallization curve. The study of these variables on N and G has a definite bearing on the mechanism of recrystallization and should lay a foundation for a rational theory on the subject. PROCEDURE The procedure used in these experiments was essentially the same as that described previously but in certain details some changes were made in the interests of speed. With few exceptions, the procedure is the same for the study of all the variables. Where the procedure is different from standard manipulations attention is called to this fact.

Jan 1, 1945

THE annual winter meeting of the A.I.M.E., which is to open in New York on Feb. 14, will be charac-terized by a number of novel features. The most important is that the technical sessions will be dis-tributed over four days instead of three as heretofore. This makes it possible to reduce the number of conflicts between sessions and also will enable each member to attend a larger number. At the same time the ses-sions are so arranged by groups that those interested only in one or more that are related can, if necessary, cover all in that group in three days as heretofore. The general excursion to which the fourth day has, for some years, been devoted has been regretfully given up, mainly because of the uncertainties of the weather in New York in February. In its place a series of group excursions are being offered at various times during the meeting, arranged, so far as possible, so as not to con-flict with any technical session likely to be of interest to those taking part in a particular excursion. Among the places to be shown the visitors are: the construction work on the Eighth Avenue subway, a real mining job; the Vehicular Tunnel, the world's greatest ventilating project; the manufacture of 42-in. conveying belts; one of the largest and most modern steam plants; a coal terminal; manufacture of mining equipment; a cable-making plant; an oil terminal and refinery. Other en-tertainment features include a smoker Monday evening with a real chance to get together and talk; an informal dance and entertainment given by the Woman's Auxiliary on Tuesday evening; the dinner-dance at the Waldorf Wednesday evening, with no long speeches; a general session Thursday evening when the Petroleum Division will present a series of important reviews of the year. An extensive program has been arranged for enter-taining the ladies, and members are urged to bring their wives. There will be dinners, teas, theater parties, shopping and sight-seeing excursions as well as the dances. The usual general luncheons for members, guests and ladies will be served each day at headquar-ters, and various committees and groups will hold lunch-eons, dinners, and round table conferences as indicated in the schedule on the page opposite. The Mining and Metallurgical Society of America and the American Society of Steel Treaters are participat-ing in this meeting and their members will be welcome as guests at any session or function. A joint conference of the Mining and Metallurgical Society and the A.I.M.E. has been arranged for Tuesday afternoon, under the chairmanship of Clinton H. Crane, at which the whole matter of the mineral reserves of this country is to be up for discussion.

Jan 2, 1927

By S. W. Miller

Most of the steel welding done at the present time is in material containing not over 0.3 per cent. carbon, and the tests here described were in similar material. These tests are not as yet completed but it is hoped that more results and more reasons for the conclusions may be presented at the meeting in February. From the time the author found the peculiar structure in electric welds referred to in a previous paper,' that is, needles or plates in the grains and similar material, in larger spots, at the grain boundaries, he has felt that these plates which may be iron nitride and probably contain some carbon, were at least partly responsible for the brittleness of electric welds. He has found but few traces of similar lines in oxyacetylene welds until the last 2 mo., he has since found large numbers under certain conditions. In the top of these welds, they are quite numerous. In the body of heavy oxyacetylene welds, they appear at times, but not nearly to the extent that they do in electric welds; the author has never seen them in the body of welds in material less than % in. (19 mm.) thick. They are shown in Fig. 82. The reason they were not noticed before is undoubtedly due to the fact that in making tests of welded pieces the weld was always ground off level with the plate, and as this structure only appears in the top 1/16 in (1-5 mm.) of the weld, they were removed by the grinding or machining; also, welds 3/4 in. thick had not been examined. It did not appear, in making bending tests, that this structure had much influence on the strength of oxyacetylene welds; while electric welds are noticeably brittle. Further, oxyacetylene welds made with certain special materials were exceedingly brittle even after the tops of the welds were removed; this was true in cases where there was no sign of the plates whatever and where the welds were remarkably free from oxide and the other usual defects. It appeared, therefore, that this brittleness did not depend on any variable that had been noticed so far, and it was decided to find where the rupture occurred in various kinds of welds made

Jan 1, 1920

The saying that a "prophet" is without honor in his own country does not always hold true, as is shown by the following from one of the local papers, which appeared under the above heading: "Edwin Ludlow, for more than seven-years vice-president of the Le-high Coal.& Navigation Co., with headquarters in Lansford, has resigned, to take effect July 1, when he will take up his residence in New York and engage as a consulting engineer. Mr. Ludlow, during the incumbency of his present position, has demonstrated his efficiency as an engineer and general manager in many directions, notable among which are the almost perfect methods in practice in the inside workings of the several operations under his charge and the erection of the most complete, most practical and most commodious breakers for the preparation of the mine product for market. In addition, his relations with organized labor have been cordial and his dealings with its representatives have been invariably based upon the principle of fair play."

Jan 7, 1919

By J. C. Irvine

Meramec Mining Co., a joint venture of Bethlehem Steel Corp. and St. Joe Minerals Corp., mines and pelletizes iron ore at the Pea Ridge mine. The Pea Ridge property is located near Sullivan, Miss., about 113 km (70 miles) southwest of St. Louis. The ore body was delineated in the mid-1950's by St. Joe during a lead exploration program. The first test holes drilled on the Pea Ridge magnetic anomaly revealed the presence of a large magnetite deposit; further drilling in 1956 and 1957 confirmed that the ore body was mineable. Meramec Mining Co. was incorporated in 1957 and shaft sinking began late in the year. Production began in April 1964. The ore body is overlain by about 400 m (1300 ft) of flat-bedded sediments. It is tabular, about 800 m (2600 ft) long and up to 180 m (1600 ft) thick. It dips about 80° and is of unknown depth. The ore is mainly high-grade magnetite with small zones of specular hematite. The wall rock is a Precambrian rhyolite porphyry.

Jan 9, 1976

By David J. Mack, Chin Bea Kim

The decomposition of the Ni-Zn eutectoid at 56 wt pct Zn was studied by isothermal transformation. Its progress was followed by metallographic, hardness, and X-ray diffraction methods. Three transformation products were found: lamellar pearlite at high temperatures; an intermediate temperature structure; and martensite at the lower temperaCures. No transition structu,ves were found. THE decomposition of the Ni-Zn eutectoid at 56 wt pct Zn was stuadied as part of a long-range program of study on the eutectoid transformation in alloy systems which do not have one or more components which exhibit allotropy. Available information on the Ni-Zn eutectoid transformation is limited to that presented in connection with the determination of the phase dilagram. No systematic studies of the eutectoid were found in the literature, alkhough the microstructures of the Ni-Zn eutectoid were reported by Tamuru.3 X-ray diffraction data exist for the ß, ß1, y , and y1 phases.' EXPERIMENTAL PROCEDURE The eutectoid alloy was prepared from "A" nickel shot and Bunker Hill super-purity zinc (99.998 pct).

Jan 1, 1962

By H. W. Morse

THE CHAIRMAN (H. W. MORSE).-Gentlemen, for the first time in the history of the American Institute of Mining Engineers, we have a full session on the subject of leaching-especially on the leaching of copper ores.. This branch of metallurgy is rather in its infancy. We have had one big plant running for a year or more, and pretty successfully; and another one which will be started in February or March, the New Cornelia. We have another one at Garfield for the Utah company, which is just designed and construction begun; and from several other points come reports of interesting test work. The first paper on the program this evening is one of some of the test work on the New Cornelia ore by myself and Mr. H. A. Tobelmann. LAWRENCE ADDICKS, New York, N. Y. (written discussion).-The Ajo proposition has had, as I understand it, two great advantages: it has not been obliged to measure leaching against flotation or some other metallurgical process, and it deals with a copper content high enough

Jan 12, 1916

By Joseph Kuti

ROOF SUPPORT DEVELOPMENTS IN LONGWALL (1) European longwall mining technology developed towards its modern form in relatively deep mines. With increasing depth the stability of openings driven for ventilation, travel or transport becomes paramount in mine design considerations. As a result the number of roadways and entries, as well as their width must be a minimum. (1) Another important aspect of European mining is the high density of mineable seams, as opposed to the wide lateral extension of a single seam in the U. S. A. Multi-seam mining requires strict planning and near 100% extraction, since with increasing depth, the effect of remnant pillars can be devastating. As a result the face layout of a modern European longwall panel is based on single panel entries of moderate width and great height. The mode of extraction is generally a mixture of the advance and retreat system which is called a 2-system. It is obvious, therefore, that the supports developed for the entries and for the intersection areas are more complex than those in the U. S. A.

Jan 1, 1981

By Sam F. Carter

FOR some time melters and metallurgists have recognized the fact that steels may be made to identical compositions as ordinarily analyzed, but with considerable variations in physical properties. Good melting practice signifies a combination of furnace operations that will produce steel with consistently good physical properties after proper consideration of cost, production efficiency, and chemical control. In acid practice, these operations may be classified fundamentally as: (I) the oxidizing boil, (2) recarburization and deoxidation, (3) slag adjustment, and (4) final deoxidation. These operations affect the properties of the steel through variations in the minute quantities of several microscopic, submicroscopic, and dissolved constituents, which are out of reach of ordinary analyses but are very influential upon the crystallographic slippage and the molecular cohesion of the structure. One of these constituents is the FeO left in solution in the steel. Herty has shown that steels high in dissolved FeO have decreased ductility and impact and increased hardness and electrical resistance. There is also much evidence that FeO in solution affects carbon solubility and diffusion, and consequently abnormality and carburizing behavior.

Jan 1, 1947

By J. H. Kittel

THE properties of the metal molybdenum have been the subject of recent investigations1,2 = which have included studies of the changes that occur in the metal when it is annealed after having been cold worked. Most of the data which have been reported have pertained to only one aspect of annealing, that is, the conditions under which recrys-tallization has been observecl. The process of recovery which may precede recrystallization docs not appear to have been investigated, and it is the purpose of this note to report observations on the recovery process in cold-worked molybdenum as determined by changes ill the thermoelectric power which occur as the metal is annealed. The measurements were made on commercially pure molybdenum wires which, after annealing at 1035°C in dried hydrogen for 1 hr, were swaged to give a series of reductions up to a maximum of 84.5 pct. The variously cold-worked wires were then annea1c.d in dried hydrogen for periods of 16 hr at progrc:ssively highel. temperatures from 200" to 1000 c with a final annealing treatment of 70 hr at. 1100°C. After each annealing treatment the ther.ma1 emf's were determined against a length of original unwo~,ked material that had received the initial hydrogen anrit,aling treatment. The difference in temperature between the hot and cold junctions was maintained at about 75'C. and. the thermal emf's were measured with a potentiometer that could be read. to 0.01 microvolt. Fig. 1 shows the thermoelectric power. (dE/dT) in microvolts per C between annclalcd and cold-worked molybdenum as a function of the degree of cold work. The effect of annealing is shown in Fig. 2. The general shape of the curves in both figures is similar to results which have been obtained for copper." It was observed that after annealing at temperatures as low as 200°C recovery was well under way. The rapid changes irt thermoelectric power observed near 900 C are probably associated with recrystallization, since such a relation has been observed with copper. Beyond 900°C the thermal emf's changed in polarity. indicating that from this point or1 the specimens were more highly annealed than the standard. Annealing treatments could not be given at temperatures higher than 1100°C due to limitations of the furnace, and it is evident that, since equilibrium values of thermoelectric powers were far from having been attained, temperatures considerably higher are required to fully anneal molybdenum. References Robert M. Parke: Molybdenum, A New High-Temperature Material. Metal Progress (1951) 60, pp. 81-96. * R. A. Long, K. C. Dike, and H. R. Bear: Some Properties of High-Purity Sintered Wrought Molybdenum Metal at Temperatures up to 2400 °F. NACA TN 2319 (March 1951): G. W. Brindley: A Thern-io-Electric Study of the Cold-Rolling and Heat-Treatment of Copper, Report of a Conference on the Strength of Solids. Physical Society, London (1948) pp. 95-106.

Jan 1, 1953

By R. F. Frantz, T. P. McNulty

The upper-level mineralization of the din Buttes, Arizona copper orebody consists primarily of dilute copper silicate impregnation in fault clay and throughout the altered limestone hostrock. Cuprite and native copper are minor with true chrysocolla rare. Owing to the high calcium carbonate and to the hydrogen ion exchange capacity of the clays, acid leaching would be economical only with cheap acid available. Leaching of the silicate copper with reagents other than sulfuric acid is slow and incomplete unless the ore is first heated to disorder the mineralized grains and to reduce partially the contained copper. Following heat treatment, 70 to 90 percent of the nonsulfide copper can be dissolved in aqueous anrmonium carbonate. Recovery of a pregnant solution by counter-current decantation is effective provided ammonium carbonate solution is added to the washing stages in order to oppose adsorption of dissolved copper by clays in the residue. Thermal stripping of the pregnant solution permits recovery of ammonia and carbon dioxide while precipitating copper either as oxide or carbonate. The research program was carried from batch tests through continuous miniplant operation to a five-month campaign in a 20 TPD continuous pilot plant. Pilot plant results, the relationships among key varibles, and a detailed flowsheet are given.

Jan 1, 1973