Search Documents

By Richard H. Rein, John Chipman

Liquid slags of the system SiO2-Ca0-MgO-A1~03 were equilibrated with liquid Fe-Si-C alloys in graphite or Sic crucibles at 1600°C in pure CO gas at atmospheric pressure, and the silicon content of both phases determined. Ternary slugs of the systern SiO2-CaO-A12O3 were also studied at 1550°C. The silicon content of the metal phase saturated with both graphite and SIC is 22.0pct at 1550°C and In the iron blast furnace, as in nearly all carbon-reduction processes, some silicon is transferred from slag to metal. The importance of this reaction is enhanced by its indirect effect on the transfer of sulfur from metal to slag, and this has stimulated a comprehensive research program on the equilibrium distribution of silicon between slag and metal. Earlier studies'-3 of this same problem provided data for calculation of the thermodynamic activities4 of the components in SiO,-CaO-A1,O3 slags. 22.4 pct at 1600°C. The temperature at which the phases cristobalite, gvaphite, $ SiC, liquid slag, Fe-Si-C alloy, and CO gas at 1 atm pressure can coexist in equilibrium was found to be 1533°C. The results agree well with earlier studies. They are shown graphically as lines of constant silicon cmtent in the metal which also are lines of constant SiO, activity in the slag.

Jan 1, 1963

By I. H. Warren, E. Devuyst

A review of the physical and chemical aspects of the direct leaching of metal oxides has been given and com- pared to recent data of the authors and co-workers. The physical aspects, including the anisotropy of the dissolution, the hydration and the zero point of charge of some metal oxides are discussed first and then the kinetics of the dissolution of metal oxides are considered. A general mechanism of the leaching of oxides which describes most of the observed results is proposed.

Jan 1, 1973

By Linn M. Farish

The estimated production of petroleum in the Dominion of Canada for 1931 was 1,582,000 bbl., an increase of 60,000 bbl. over 1930. Nearly all of the production came from Alberta, with a small quantity from Ontario, and a very minor amount reported from New Brunswick. At the beginning of 1931 it was hoped, and predicted, that a substantial increase in production would be shown for that year, but such was not the case, since Alberta did not show the anticipated gain. The production from Ontario and New Brunswick has not varied more than a few thousand barrels during the past 10 years and aggregated 124,000 bbl. in 1930, with 126,600 bbl. estimated for 1931. Unless new fields are discovered, production in 1932 will decline, with Ontario and New Brunswick showing little change and Alberta declining appreciably. Canadian production by provinces during the past 10 years is given in Table 1. Furnished by the Dominion Bureau of Statistics. a Barrels of 35 Imperial gallons or 42 U. S. gallons. c Figures for Ontario and New Brunswick are estimated. The production of natural gas in Canada reached the record figure of 29,377,000,000 cu. ft. in 1930 and it is estimated at 26,874,600,000

Jan 1, 1932

By L. B. Lindemuth

TO those who are in a position to carry the thought to a conclusion, I would like to present a theory of the cause of blisters in ' galvanized sheets. Blisters that are caused from piping and shrinkage cavities will not be considered, because the reason for their formation is entirely obvious. Blisters that periodically occur, with no apparent system of location, number, size or grouping, and then disappear with no apparent change in manufacturing method, are the ones to which this theory would apply. Examination of blisters of the latter type has shown that they contain hydrogen gas at atmospheric pres-sure, and that occasionally traces of oxide or sulfide are found on the inner surface of the blisters. These two characteristics have led to the rather general idea that hydrogen gas generated in pickling, and that iron oxide supposed to be inherent in the ingot and causing weak spots, were, in some manner, responsible for the development of blisters in galvanizing. The theory which I wish to advance is that these blisters are caused by moisture that has penetrated the steel after the annealing operation. This moisture comes from the atmosphere, or from pickling or wash-ing, and when it is suddenly expanded into superheated steam in galvanizing, the increase in volume is so great that it cannot escape with sufficient rapidity through the small opening which it entered as moisture. The pressure so generated forces the sheet apart along those lines of lamination that may be found in practically all flat sections of steel rolled comparatively cold.

Jan 5, 1927

By K. V. S. Sastry

INTRODUCTION Flotation is by far the most important unit operation of mineral processing. Most of the common base metals are produced from flotation concentrates of metal sulfides. Flotation is proving to be a valuable process for producing non-metallic minerals such as ceramic oxides, silicates, clays and phosphate fertilizers. All these fltation separations are carried out on materials which are predominantly in the 10 to 100 micronssize range. The present practice of flotation circuits for the production of large tonnages of metallic and non-metallic mineral concentrates is fairly well understood, developed, and standardized. Two kinds of problems are encountered (1, 2) with fine particles smaller than 10 microns. First is the interference of the fine particles with the flotation of the coarser particles and the second is the poor flotation behavior of fine particles. In general, these problems are handled either by eliminating, minimizing, or ignoring the fines in the flotation circuit feed. In recent years, however, a considerable number of experimental and theoretical studies have been carried out to understand the flotation behavior of fine particulates. This literature is summarized in four review papers (2-5). Application of the conventional flotation techniques for the separation of mineral fines is known to be uneconomical, and to present several scientific and technological problems (1-5). The objective of this presentation is to examine the flotation behavior of fine particles in terms of their physical-chemical properties and to review the potential techniques of fine particle flotation. Specific reference to the problem areas and research needs will also be included in the discussion.

Jan 1, 1979

By F. V. Lenel, J. A. Dromsky

The influence of thermal and mechanical treatments upon the elevated-temperature stability, the microstructure, and the mechanical properties of aluminumaluminum oxide alloys is investigated. Compacts from atomized and flake aluminum powders were sintered at temperatures just below the melting point of aluminum in a vacuum of 10-4 Torr for several hours and were then hot-extruded. During this treatment the hydrated oxide present on the surface of the powder particles decomposes, the water vapor produced reacts with the aluminum forming additional oxide, and the hydrogen developed is removed by diffusion to the surface. Extrusions of compacts so treated are stable at temperatures up to the melting point of aluminum and do not form blisters and internal defects typical of extrusions from untreated powder. Electron micrographs of extrusions from unsintered compacts show long parallel oriented platelets typical of the IN previous investigations1,2 the properties and structure of aluminum alloys were described which had been produced by cold compacting aluminum powder and then hot pressing and extruding the compacts. Both the structure and the properties of these alloys differ significantly from those of commercially produced aluminum-aluminum oxide alloys. When commercial alloys are produced, they are given a sintering treatment in air at about 600°C between cold compacting and hot pressing.3 During this treatment the hydrated oxide, which forms the coating on the aluminum-powder particles from which the alloys are prepared, is decomposed.4 The chemically bound water which is released reacts with the aluminum and forms aluminum oxide and hydrogen. Most of the hydrogen is eliminated by hydrated oxide skins on the original powder particles, while the oxide particles in extrusions from sintered compacts are broken up. The strength of extrusions from treated powder is somewhat lower, but their ductility is considerably improved over that of extrusions from untreated powder. The slip-trace patterns on electron microgvaphs of extrusions which had been strained in tension before replication indicated that the grain size of the extruded alloys was approximately the same as that of the original powder particles. Coarse-grained alloys were produced by severe cold work and annealing of the extrusions. They have significantly lower room-temperature strength, but about the same ductility as the vacuum-sintered fine-grained alloys. The size and shape of oxides in the coarsegrained alloys is similar to those of the fine-grained alloys, but the particles are somewhat more uniformly distributed. diffusing to the interior or exterior surfaces of the compact, but it is difficult to eliminate all of it because the solubility of hydrogen in solid aluminum is very low even near its melting point. Extruded alloys which are not sintered before hot pressing and extrusion appear quite sound upon metallo-graphic examination, but develop severe surface blistering and internal fissuring when they are heated to elevated temperatures after extrusion. Fissures and blisters have been observed even in commercial alloys which had been sintered in air, although they are much less severe.' Because of the importance of this sintering treatment it was studied in this investigation in a modified form, using vacuum sintering rather than sintering in air, to insure more complete elimination of occluded hydrogen. The technique is described and the effect of the treatment upon the structure of the alloys is documented. It has been known for some time that extruded aluminum-aluminum oxide alloys are very finegrained, but an exact delineation of grains in electron micrographs has not been possible. In the conventional metallographic-etching techniques etchants attack the interface between the second-phase particles and the matrix in the alloys much

Jan 1, 1964

Henry Louis, Newcastle-upon-Tyne, England (communica, tion to the Secretary): I have been much interested in Mr. Schmitz's description of the copper-ore bed in the Permian formation of Texas. He compares it with the Mansfeld Kupferschiefer; but it seems to me to present closer analogies with a small deposit on the same side of the Atlantic, in Nova Scotia, which I examined in 1877. I quote entirely from my fieldnotes, made then, and from specimens still in my possession. These copper-deposits are known in several places; but I examined them at the village of New Annan, on the banks of the French river. This district has been determined by Sir J. W. Dawson as being of Permian age, and this determination seems to have been confirmed as recently as 1891 by the operations of the Canadian Geological Survey. The following is the section, very imperfectly exposed in a few shallow levels, described in ascending order: Red sandstone, moderately fissile and markedly false-bedded. Lower nodule-bed, 1 inch to 6 inches thick, of fissile mica, ceous sandstone, containing obscure plant-remains converted into anthracite, chalcopyrite, chalcocite and iron pyrites. Very coarse grit or, in places, red sandstone; thickness and character variable. Upper nodule-bed, 6 inches to 2 feet thick exceptionally, generally about 10 inches. Soft, gray, friable shaly sandstone, with nodules of copper-ore. Red sandstone. All these strata lie flat, in places quite horizontal, in places dipping towards the river at 5° to 10°.

Jan 1, 1897

By Arthur Taggart

FLOTATION of sulphide minerals and native metals is no longer a practical difficulty. The underlying scientific principles of the method, although not explored in anything like complete detail, have been formulated with sufficient breadth so that the direction of attack on any specific case is clearly indicated. It has been known since the earliest clays of flotation that certain of the nonsulphide nonmetal minerals-e.g., sulphur and graphite-would respond to flotation by oils as sulphides do; therefore they have been grouped with sulphides in many patents. But since the development of the chemical theory of collection,1,2,3 this similarity in action has been one of the facts cited in disproof of the theory by opponents of the hypothesis.4,5,6 Air levitation? of certain oxidized minerals, both metalliferous? and nonmetalliferous, and separa-tion thereby from other oxidized minerals, is a recent development in practice, although the discovery of the method dates back 17 years.7 This paper presents evidence that the principles underlying the air levita-tion of the nonsulphide nonmetal minerals are the same as those utilized in the flotation of the sulphides and native metals. It will be apparent immediately to anyone with knowledge of mineral concentration that separation of air-levitated minerals in water from minerals not so levitated is a simple matter of water-gravity concentra-tion, the separating device employed depending solely upon the size of the particles treated and the buoyancy differences effected by the levita-tion, The usual separating means employed are: (1) a flotation machine for fine, slimy and for well aerated granular material; (2) shaking tables for granular less aerated material.

Jan 1, 1937

By D. R. Uhlmann, T. P. Seward, K. A. Jackson, J. D. Hunt

microscopic ohservations on alloys of organic trzaterials show that dendrite arms can melt off under normal conditiorzs of growth. This occurs because of the interactiorz of' heat and matter fluxes during dendritic growth. The re melting occurs where the den-drite arms are joined onto the main deizclrite sterrz. Many detached crystals can be produced in this fashion. It is postulated that this remelting phenornenon occurs in metal alloys, giving rise to the equi-axed region in castings. Experiments peyformed orr castings of transparent materials support remelting as a primary source of detached crystals. Ob~ervations an equiaxed tones in metal castings are discussed in terms of this and other mechanisms. It is concluded that the partial remelting of dendrites is on important mechanisnl for producing the equiaxed regions in castings. THE freezing of a casting can be divided into three regions: a chill zone formed near the mold wall, a columnar region, and a third region, at the center of the casting, which is called the equiaxed zone. The origin of the grains that comprise the equiaxed region is the subject of this paper. We will first outline the mechanisms which have been proposed to account for the origin of the equiaxed region and discuss some recent experiments which cannot be explained by these theories. We will then present some microscopic observations of dendritic growth which have led us to conclude that the equiaxed zone in castings can arise from partial remelting of dendrites. This proposal is supported by observations on transparent castings. Finally, we will discuss several observations on metal castings which could not be explained previously, and which can be accounted for by the present proposal. Previous Mechanisms. Winegard and Chalmers3 pointed out that the molten central region of an ingot could be constitutionally supercooled, because of the solute layer at the growing interface. In this supercooled region, nucleation on particles could occur, giving rise to the equiaxed crystals. Another mechanism has also been suggested,4y5 that the nuclei originate in the chill zone then float or are carried by convection to the center of the casting, where they grow to produce equiaxed crystals. In this case, all the crystals nucleate immediately on casting, so this mechanism will be termed "big-bang" nucleation. Walker's Experiments. J. L. Walker has made observations on the solidification of nickel and Ni-Cu alloys which cannot be accounted for by either of the above mechanisms. In studying the grain size resulting from freezing of nickel at various undercoolings, walker6 found that at large undercoolings the grain size was small, due to mechanical nucleation, as discussed by walker7 and Horvay.' At small undercoolings, the grain size was large, and the growth dendritic. In Ni-Cu alloys, however, for initial undercoolings starting from just below the melting point and extending for a hundred or so degrees of undercooling, fine grains were also observed. Samples were undercooled 200 Centigrade degrees without nucleating, and were then heated 130 Centigrade degrees so that the undercooling was 70 Centigrade degrees, and nucleated. The samples had a small grain size, indicating multiple nucleation. There were no heterogeneous nuclei in the liquid which could operate at the temperature of growth. Constitutional supercooling could not have been greater than the supercooling of the initial melt, since the temperature rose as the freezing continued. walker -as also shown that a Ni-Cu alloy which can be undercooled to below its solidus will produce typical columnar and equiaxed regions when cast into a cold mold. This alloy could not reach a temperature below its solidus by constitutional supercooling. It could not, therefore, have nucleated heterogeneously. Neither the big-bang mechanism nor the Winegard-Chalmers mechanism can account for the fine grain

Jan 1, 1967

A group of prominent engineers and contractors of Chicago and vicinity have cooperated in forming a Joint Committee on Military Engineering. The founders are members of all of the leading engineering and contracting organizations of Chicago, including the local branches of the national engineering societies. The purposes of the Committee are to further military preparedness among engineers, contractors and their associates by the following means: (1) Courses of lectures; (2) assigned reading; (3) studies and practical instruction in military engineering;. (4) assisting engineers to qualify as officers in the National Reserve Corps of Civilian Engineers; (5) urging enlistment in and support for engineer troops of the National Guard and such other organizations as the Government may create; (6) furthering instruction in military engineering in training camps and the attendance in them of those qualified; (7) by such other means as from time to time may be deemed advisable. The Joint Committee has already prepared a program covering the vital points outlined. To date the program is practically complete for a period extending from April 20 to July 25. Something of interest will be taken up each week, including lectures by Lieutenant-Colonel W. B. Judson, Engineer Corps, U. S. Army; two lectures by Major P. S. Bond, Engineer Corps, U. S. Army; Lieutenant-Colonel Mason M. Patrick, Engineer Corps, U. S. Army, and several exhibition drills, terrain exercises and inspection trips under the direction and guidance of various officers of the Engineer Troops of the Illinois National Guard. Additions to the program will be made from time to time. '

Jan 5, 1916

A group of prominent engineers and contractors of Chicago and vicinity have cooperated in forming a Joint Committee on Military Engineering. The founders are members of all of the leading engineering and contracting organizations of Chicago, including the local branches of the national engineering societies. The purposes of the Committee are to further military preparedness among engineers, contractors and their associates by the following means: (1) Courses of lectures; (2) assigned reading; (3) studies and practical instruction in military engineering;. (4) assisting engineers to qualify as officers in the National Reserve Corps of Civilian Engineers; (5) urging enlistment in and support for engineer troops of the National Guard and such other organizations as the Government may create; (6) furthering instruction in military engineering in training camps and the attendance in them of those qualified; (7) by such other means as from time to time may be deemed advisable. The Joint Committee has already prepared a program covering the vital points outlined. To date the program is practically complete for a period extending from April 20 to July 25. Something of interest will be taken up each week, including lectures by Lieutenant-Colonel W. B. Judson, Engineer Corps, U. S. Army; two lectures by Major P. S. Bond, Engineer Corps, U. S. Army; Lieutenant-Colonel Mason M. Patrick, Engineer Corps, U. S. Army, and several exhibition drills, terrain exercises and inspection trips under the direction and guidance of various officers of the Engineer Troops of the Illinois National Guard. Additions to the program will be made from time to time.

Jan 5, 1916

By H. C. Fiedler

X HE development of the cube-on edge secondary re-crystallization texture in Si-Fe strip requires that normal grain growth be restrained. It has been shown that the degree of restraint and hence the completeness of secondary recrystallization depends upon the size and number of second-phase particles, which in turn is dependent upon the prior processing history.1y2 The purpose of this note is to show that, for heats in which manganese sulfide particles are providing the restraint to grain growth, the choice of hot rolling temperature depends upon the manganese content. The making and processing of the heats to the final gage of 0.012 in. has been described.3 The compositions are given in Table I. Apparent in Fig. 1 is the decrease in the ability of strips hot-rolled from 1175°C to undergo secondary recrystallization as the manganese content increases. It has been shown that 1175°C is below the solubility temperature of 0.014 pet S in even the 0.038 pct Mn alloy: and the observed behavior is attributed to an increasing fraction of the sulfur forming large manganese sulfide particles at the heating temperature for hot rolling. This fraction of the sulfur is thus unavailable to subsequently form the small, uniformly dispersed particles which are needed to restrain normal grain growth. Since the sulfur is completely in solution at 1325°C,3 strips from all three alloys show strong secondary recrystallization behavior when hot-rolled from that temperature.

Jan 1, 1969

By George F. Becker

Complexity of Rock-Fractures.—The strains to which rocks have been subjected are manifestly very complex, and it is entirely safe to presume that every possible mode of deformation and rupture is exemplified. The most superficial inspection of any ordinary mountain region is sufficient to assure the observer that the rocks have been pressed, stretched, bent, buckled, twisted, and shorn. The study of torsional rupture cannot fail, therefore, to throw light on geological phenomena. The question is how areas which have been broken in this manner are to be distinguished from those which have yielded to other systems of forces. Phenomena of Joints.—It is well known that a large part of the more homogeneous rocks and some very heterogeneous rocks are intersected by partings often ailed joints. These partings are frequently flat surfaces even when seen in very large exposures, but are sometimes surfaces of moderate, single, or double curvature. Joint, usually occur in groups, in each of which the several partings are parallel to one another, and several such groups often intersect the same rock-mass. In such cases the different systems make large angles with one another. Nearly all students of the subject of jointing have reached the conclusion that joints are faulted surfaces, the dislocations usually being of small amplitude; and this conclusion receives abundant support from the study of thin sections under the microscope. It has thus been shown that much even of what would be regarded in hand specimens as mere slaty cleavage

Jan 1, 1895

By Edward H. Robie

THOUGH the final figures are not available as this is written, it seems certain that the Institute accounts will show $7000 to $8000 surplus for the year 1951. This is the first time this has happened since 1941. No money had to be taken from any of the Funds to bring about this happy condition. Furthermore, the amounts allowed for depreciation, bad debts, and inventory adjustment were more liberal than in the past. Income increased some $29,000 over 1950. Dues received from old members increased moderately, but dues from new members dropped off $2000 and from initiation fees quite severely-from $17,000 to $11,000. The number of new members did not come up to expectations and a change in procedure caused a delay in getting some of them on the rolls. A large number of the new members paid an installment of $5 on their initiation instead of the full $20. Junior Members, of course, pay no initiation fee. Brightest spot in the income picture was the increase in advertising income-from $103,000 in 1950 to $143,000 in 1951. All three of the journals shared in this, Mining being up $18,000; Metals, $9000; and Petroleum $13,000. Nonmember sales of the journals dropped off slightly, and sales of Transactions volumes more so from $35,000 in 1950 to $27,000 in 1951, with a further drop of $5000 accounted for by a change in accounting procedure. On the other hand, sales of other publications increased by $10,000.

Jan 1, 1952

By R. M. Rose, D. P. Ferriss, J. Wulff

The effect of orientation on the stresses, nctivation energies, and activation volumes for yielding and plastic flow of tungsten single crystals was investigated. Tensile tests showed the proportional limit to be a function of orientation: crystals whose tensile axes were near the [I10} direction were roughly three times as strong as [loo] crystals. The [ 1101 crystals showed low strain hardening and displayed yield phenomena, whereas the other orientations yielded smoothly and showed considerable strain hardening. The fracture mode was cleavage, except for crystals near the [1101 , many of which gave "chisel" fractures at 300°and 373°K. The activation energy for yielding was approximately one- half an electron; volt at all orientations, and the volume of activation was (12 to 14)b3, except near the [1101, where it was 7b3. Activation volumes generally increased after yielding. The most common theoretical models for yielding and strain hardening of bcc metals were. found to be insufficient to the intepretation of the observations here in. An explanation is proposed, based on the dislocation reaction dislocation networks and jogs, md jogs formed during plus tic flow. PRECLSE knowledge of the Drocesses involved in the yielding and plastic flow of the refractory metals is essential to the formulation of models for their flow and fracture. Despite this need, the single -crystal investigations, especially of tungsten, have been sparse. Slip occurs at low temperature, according to schadler,i in <111> directions on {110) planes; as the temperature rises to room tempera-

Jan 1, 1962

By J. J. Rutledge

I. Description of the Clinton Ores and Associated Rocks. The Clinton rocks in Stone valley comprise (1) thick layers of deep-red shale, (2) layers of reddish-gray shale interspersed with beds of sandstone and thin beds of extremely fossiliferous limestone, and (3) yellowish-gray shales alternating with thin layers of olive-colored shales. These layers of shale are all very thin and are at no point massive.&apos; A bed of gray-white sandstone varying in thickness from 12 to 30 ft. occurs in the upper portions of the Clinton shales. This is called the ore sandstone, a name given to it by Rogers and adopted also by the Second Pennsylvania Geological Survey. It is the surest guide to the presence of the iron-ore bed, which lies below its lower edges at distances varying from 10 to 20 ft. This ore sandstone, in the valley, lies generally at very low inclinations, but often is locally subjected to considerable changes in dip. At its outcrop this ore sandstone weathers very easily and yields a rather sparse crop of stone, composed of dirty, iron-stained boulders. Upon the roads these boulders are quite well rounded, and bear fragments of crinoid stems and other fossil forms. The ore sandstone exhibits at many points evidences of former movements in this very great thickness of the shales, and as it is the only stratum in this series competent to transmit and record stresses due to structural movements, its evidence is of considerable importance in determining the occurrence of movements in times past.

Jan 1, 1910

By Earle E. Schumacher

THE elements silicon and germanium are not metals within the usual, intuitive association of the word, nor are they so within a stricter definition based on the electronic binding. Two properties associated with metals are plasticity and high electrical conductivity. These elements crystallize in the diamond cubic structure, an arrangement apparently not very favorable to slip, and are therefore brittle rather than ductile. Their electrical conductivity is not like that of metals the atoms are locked together by the covalent bond, which in pure and perfectly arranged material leaves but few electrons free to act as electrical carriers.† In further contrast to metals, their electrical conductivity can be greatly increased by raising the temperature. Yet silicon and germanium are not ideally nonmetallic. They are hard, solid, and possess a metallic luster. They exhibit that peculiar brand of electrical conductivity conveniently termed "semi- conduction," wherein, as shall be seen, lies much of their importance. Both, but silicon in particular, are important components in real metallic alloys and the methods of their reduction and preparation lie clearly in the province of the metallurgist. From their duality of physical and chemical properties, silicon and germanium, along with such elements as boron, diamond, gray tin, selenium, antimony, and arsenic, are considered semimetals or metalloids. Because of their importance to metallurgy and the im-

Jan 1, 1953

By Theodore Nagel

Fuel-oil, natural gas and coke oven gas, producing the higher temperatures of open-hearth current practice, have been gradually displacing producer gas the lowest cost fuel for open hearth operations. The lower temperatures of combustion products from producer gas is caused by nitrogen dilution. Practical Application of Combustion Thermochemistry One pound of carbon burned to CO produces 3,960 B.T.U. and one pound of carbon burned to C02 produces 14,140 B.T.U. The second unit of oxygen uniting-with gasified car-bon (-CO) produces (14,140 - 3,960) 10,180 B.T.U. which is;(10,180 - 3,960) 6,220 B.T.U. more heat than produced by the first, unit of oxygen forming CO by uniting with solid carbon. A review of the relative combustion heating values of commercial gaseous fuels reveals CO requires a minimum of air for combustion, and because of minimum nitrogen dilution and the high thermal release from CO higher temperature combustion products are produced from CO than from natural gas or from coke-oven gas under similar combustion conditions. Inert nitrogen diluent lowers the calorific value of fuel gas and its diluting effect is cumulative in lowering the temperature of the products of total, combustion. It is not only logical but, practical in partial combustion, converting bituminous coal to gas, to generate the gas, with reduced nitrogen dilution.

Jan 1, 1936

By Theodore Nagel

Fuel-oil, natural gas and coke oven gas, producing the higher temperatures of open-hearth current practice, have been gradually displacing producer gas the lowest cost fuel for open hearth operations. The lower temperatures of combusts on products from producer gas is caused by nitrogen dilution. Practical Application of Combustion Thermochemistry One pound of carbon burned to CO produces 3,960 B.T.U. and one pound of carbon burned to C02 produces 14,140 B.T.U. The second unit of oxygen uniting with gasified carbon (CO) produces (14,140 - 3,960) 10,180 B.T.U. which is (10,180 - 3,960) 6,220 B.T.U. more heat than produced by the first unit of oxygen forming CO by uniting with solid carbon. A review of the relative combustion heating values of commercial gaseous fuels reveals CO requires a minimum of air for combustion and because of minimum nitrogen dilution and the high thermal release from CO higher temperature combustion products are produced from CO than from natural gas or from coke-oven gas under similar combustion conditions. Inert nitrogen diluent lowers the calorific value of fuel gas and its diluting effect is cumulative in lowering the temperature of the products of total combustion. It is not only logical but practical in partial combustion, converting bituminous coal to gas, to generate the gas with reduced nitrogen dilution.

Jan 1, 1936

By G. Broughton

For the past few years a great amount of work has been done on the viscosity characteristics and gelation of clay suspensions, much of which has been reported in papers published by the Institute.7,12,18,19,24 Impor-tant reviews have been made elsewhere by Evans and Reid,10 Marshall20 and Clews, Macey and Rigby,8 the last two on the general properties of clay. It is unnecessary, therefore, to recapitulate past work beyond recalling that three explanations for the high viscosity and gelation of clay suspensions have been put forward. For lack of more exact nomencla-ture, these may be called the water hull,16 mechanical interference" and attraction-repulsion" theories. The first pictures the clay particles as surrounded by relatively rigid water envelopes, which increase effective volume; the second emphasizes the mechanical interference of platy particles or their agglomerates; while in the third the particles are assumed to be held relatively rigidly at a distance from each other determined by the balance between the attractive (van der Waal&apos;s) forces and the elec-trical repulsions of the charges. 13,14 This article presents fresh data on clay suspensions, particularly on the influence of previous flow history of the suspensions, specific contra-ions, temperature, solvation and particle size, in an attempt to contribute to the solution of the problem.

Jan 1, 1938