Search Documents

By W. R. Opie, O. W. Mole

By confining the electrolytic reduction of TiCl4 to the interior of a porous basket-cathode the electrolyte between the anode and the cathode can be kept free of reduced chlorides of titanium eliminating undesirable reactions of reduced titanium chlorides with brickwork or oxygen in the cell atmosphere. Semiwalls are not needed. Operating conditions are given and discussed. Titanium yields based on TiCl4 introduced are 93 pct. Cell voltage and amperage characteristics are adaptable to multiple cathode-series cell urmngements. EXPERIMENTS conducted in the National Lead Co., Titanium Division, Research Laboratories showed that titanium metal could be deposited in an electrolytic cell in which titanium tetrachloride was introduced through a tubular cathode.' The reduced chlorides as formed were confined to the vicinity of the cathode. They were reduced to form a cocoon-shaped growth of sponge titanium metal at the end of the cathodic tube below the surface of a sodium chloride-strontium chloride electrolyte. No diaphragm was needed.' Although high-purity, coarse crystalline metal was produced in the cocoon growth, the yields of metal removed from the cell, based on the amount of titanium introduced as TiCl4, were usually only 40 to 60 pct. The growth of the cocoon deposits was away from the cathodic tube for introduction of TiC14 toward the anode following the flu lines. The reduced chlorides of titanium diffused through the deposit and were reduced to titanium electrolytically within the deposit or on the outer surfaces. Deposition within the pores of the cocoon was detrimental to further deposition because it plugged the passages used by the reduced chlorides to diffuse away from the point of titanium introduction. As plugging due to deposition in the pores proceeded, the reduced chlorides in the center of the cocoon would force their way out by forming a channel and would escape from the vicinity of the cathode without being reduced to metal. Some work had been done previously1, 2 which indicated that if the end of the cathodic tube for introducing TiC14 was surrounded by a screen connected to the tube so that it too was cathodic, growth could be made to occur within the screen. Direction of growth was observed to be from the screen toward the point of TiCl4 introduction. Through a series of design modifications a cathode evolved which consisted of an introduction tube surrounded by a perforated metal basket as shown in Fig. 1. Modifications of this design are described in Refs. 3, 4, and 5. This basic cathode designa" was incorporated in electrolytic cells containing graphite anodes and constructed of high-silica brick refractory for containing the electrolyte (see Fig. 2). The inner crucible was surrounded by insulating brick and the entire unit contained in a welded steel shell. Suitable cooling chambers with inert gas atmospheres were devised so that the cathode could be removed from the cell without exposing the deposit to air while hot. Various alkali and alkaline earth chlorides were used as electrolytes.

Jan 1, 1961

By AIME AIME

FOR many years it has been the invariable custom of the Institute, in addition to its annual meeting in February, to hold a technical meeting in the fall in some mining or metallurgical center in the West. As the activities of the Institute have increased, and especially since the absorption 'of the American Institute of Metals, there have for a number of years been two fall meetings. Never before in the history of the Institute have there been three meetings in addition to the annual meeting in February; in 1920, however, three important fall meetings are to be held. The general Institute trip will be made this fall to the Lake Superior iron and copper country. Members will leave Buffalo on August 20 by steamer, visit the copper mines in and about Houghton, the iron mines of the Marquette and Iron Ranges of Michigan and the iron mines of the Mesabi Range in Minnesota, and' return to Buffalo by steamer on September 3. Technical sessions will be held at Houghton, Minneapolis and Duluth. For a long period it was customary for the Institute to visit the Lake Superior country about every seven years. This trip, however, will be the first visit since 1904. The unprecedented development in both copper and iron mining in this section during this period will make this trip of unusual importance. In addition, a notable series of papers will be presented.

Jan 1, 1920

By Sidney H. Haughton

FOLLOWING the discovery of diamonds in 1870 and the Witwatersrand gold fields in 1886 South Africa changed from a predominantly pastoral country with a scattered white population into a land whose economy came rapidly to be based primarily on mining. The total value of the mineral output of the Union in 1944 was approximately $493,000,000, to which gold contributed 84 per cent. Gold furnished some 33 per cent of the Union Government's total revenue in that year, and approximately half the country's population obtained its livelihood directly or indirectly from the gold mining industry. In any review of the Union's mining activities and in any consideration of the country's future, gold mining must occupy a prominent place. It is generally conceded that the present structure is not properly balanced and that an economy based on a preponderance of a single nonpermanent factor possesses potentialities of serious instability.

Jan 1, 1946

By F. O. Garrabrant, F. S. McNicholas, Robert Henderson, R. U. King

Several years ago, it was decided to experiment with the use of high-pressure water to bring in finger hangups and reduce the amount of secondary blasting necessary. It was argued that the velocity effect of the high-pressure water would bring down hangups without unduly wetting the ore. Water under a head of about 550 ft. was installed in certain slusher drifts. Ordinary ¾ in. water hose, with a nozzle opening of % in., was used, and water was impinged on the fines under a hangup. Results were excellent. About half the total number of hangups were brought in with high-pressure water without blasting and the cost of this part of the slushing operation was reduced about 50 per cent. Operations were speeded up, dust counts and safety hazards were reduced, and a more desirable working place was secured. The additional water added to the ore was under one per cent and caused no inconvenience in slushing, haulage, or crushing operations. Usually the ore would absorb all of the water, so that none of it would enter the loading drifts. The entire mine, developed by slusher drifts, is being equipped with high-pressure water. Heating Mine by Compressor Cooling Water Several years ago, the problem of heating certain sections of the mine during freezing weather became important. It was calculated that there was sufficient heat in the compressor cooling water to heat the incoming ventilating air current to above freezing, if such heat could be transferred from the water to the air. All schemes of radiation from pipe were rejected as too cumbersome, costly and impractical. It was thought that by spraying the heated water from the compressor cooling system into the incoming air, a satisfactory heat exchange could be accomplished. The only objection was that the sprayed water would freeze and might fill the air-intake drift. However, when water at about 75° to 80°F. was sprayed at the rate of 200 gal. per minute through a bank of sprays into the incoming and freezing air current, this air was thereby heated to above freezing; and although some ice was built up in the air drift, the amount was not objectionable. Occasionally the built-up ice was picked down into the outgoing water stream, which removed it. The entire south and westerly parts of the mine were prevented from freezing. Concreting for Hangups Considerable trouble was experienced in securing hangups of fine ore in slusher fingers that needed repairing. Regular methods of timbering were unsatisfactory. Now, a slab of concrete is poured over the top of the muck by Pumperete machine, almost filling a finger, which gives a satisfactory slab to work under for making the needed repairs. Derailers Some trouble has been caused by motor-men not observing safety lights and

Jan 1, 1946

By Clarence P. Linville

It is recognized that, in all metallurgical operations, the greatest possible uniformity in all conditions is essential to the best results. It is the constant aim of metallurgists to secure this uniformity, and their success in this respect has been in many cases the cause of great advances in the metallurgical processes themselves. Of all such processes, the production of pig-iron in the modern blast-furnace is perhaps the most complex and the most difficult of control. Notwithstanding the great progress of recent years, there is still great difficulty in obtaining anything like uniform conditions and results in the manufacture of pig-iron. The reason is not far to seek. The ores vary in composition and physical properties, often carrying a varying amount of gangue material, unevenly distributed. The coke may vary in composition, cell-structure, moisture, hardness, and other properties. The blast, the weight of which far exceeds that of any other constituent, varies in its moisture-content and consequently in its chemical composition; and its temperature, by reason of the method of heating, is not uniform, but, besides varying from time to time with atmospheric and other outside conditions, has a maximum and minimum for every changing of stoves. Now, with regard to these variations, the modern demand for uniformity has been greatly aided. Chemical analysis has made it possible to select ores so that the composition of the charge can be kept fairly constant; coal may be obtained from a given field, and coked in the same kind of ovens under conditions which make the fuel practically uniform; the Gayley

Jan 1, 1911

By HOWARD N. EAVENS

DURING the year just closed the bituminous industry has been marked by a continuation of the period of low prices and a steady deflation, accompanied by the closing of mines and the consolidation of small units into larger ones. This pro- gram has marked almost every field in the country, and it bids fair to continue for some time. Some figures recently published for Kentucky show that in 1924 there were 660 mines producing 45,147,000 tons; in 1928 the number had decreased to 537, while production had increased to 61,860,000 tons, and a similar movement is occurring all over the country. Prices throughout the early part of the year were very low, but during the fall and winter the prices received are more satisfactory than they were earlier in the year. One of the leading developments in the marketing of coal during the year was the trade practice movement, which began in the Harlan field, and has now been adopted in the Harlan, Hazard, Appalachian, Logan. Williamson and Kanawha fields. The purpose of this movement is to prevent the shipment of coal except on order, and by the publication of price lists to prevent much senseless price quotation. Where it has been practised the longest this movement has resulted in a considerable degree of stabilization, and, undoubtedly, it will help existing conditions very materially if it becomes universal.

Jan 1, 1930

By AIME AIME

THE following paragraphs comprise such information as the Secretary has been able to obtain concerning the members and associates whose deaths have been reported. Further particulars or corrections of errors, and biographical data concerning deceased members or associates not already noticed in this way, are solicited. [SECRETARY'S NOTE.-All of these notices have been revised, and some of then have been more or less completely prepared, by me. To those which contain more particularly the expression of my personal feeling, my initials have been appended. The labor of preparing or editing these paragraphs has been in many respects both welcome and interesting, on the one hand, and sorrowful, on the other. In going through the list, I have repeatedly felt like one who, visiting the Morgue, suddenly comes upon the pale face of a dear friend, of whose death lie was not aware ; and, even when this fact was known to me, the work of recording it has brought upon me a flood of recollections, almost preventing the discharge of that official duty. The list for 1907 seems to me to he peculiarly sad, comprising, as it does, so many sudden deaths by violence or accident, so many veterans, removed too soon, and so many young men whose early departure impoverishes the future, even more than the present. Probably, this feeling on my part is largely due to the circumstance that the increased membership of the Institute necessarily in¬volves an increase of the annual death-list. Probably, also, it is connected with the circumstance that during the first years of the history of the Institute-say from 1871 to 1880-it was joined by men of all ages, and that the death-rate is consequently now above the average which would result from the normal annual addition, principally of young men. And finally, I must admit that, as one of the original members of the Institute, and practically connected with it for nearly thirty-seven years as Acting President, President or Secretary, I am peculiarly impressed and depressed by the successive deaths of those who were my associates in the years of its early struggles and triumphs. I do not wish to inflict upon my younger colleagues the melancholy reflections of an increasingly lonesome old man. In fact, my prevailing mood concerning the Institute is not at all melancholy, but triumphant and hopeful. If I may be permitted to preach at all, I would enforce, from the texts given below, a moral which many of them declare so forcibly as to preclude the necessity of expository enforcements-namely, the duty of every one of us, old or young, to give to his brethren, as he goes along, and without waiting for some future occasion for a comprehensive and monumental contribution to technical literature, the results of his observation and experience. When I look at this list of names, my personal sorrow over many of them is drowned in my professional reflection as to each and all-How much has died with

Jan 1, 1908

By AIME AIME

THE value to the engineering profession of a liaison between the engineering societies of Russia and America, through Engineering Council, was the subject of a meeting in the Engineering Societies Building attended by over 500 persons. In introducing the subject, Mr. N. A. Stephanoff, President of the Russian Society of America, said: In Russia, engineers were divided into two classes: those who had graduated from the high technical schools and the practical engineers who had graduated from special technical schools. These technical schools were divided into three groups: The first corresponded to the German polytechnical schools with many departments, mechanical, chemical, metallurgical, mining, etc. The second group corresponded to the French special schools of the "Écoles des Ponts et Chaussées." "École des Mines." The third group was formed by the Military and Naval Academies of Engineers. In 1910, Russia's high technical schools had about 45,000 students, whose training covered a period of not less than five years, and who enjoyed all opportunities afforded by laboratories in no way inferior to those of Germany.

Jan 1, 1920

By E. L. Kinsella, F. S. White

Solids fluidization utilized in two ways for the commercial production of lime is described. Crushed —6 mesh limestone is dried and dedusted in a single bed reactor, then calcined in a 5-stage reactor. Construction, operation, and results obtained with both processes are given. THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,' showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.' Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime- stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a -in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontallv at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1953

By F. S. White, E. L. Kinsella

Solids fluidization utilized in two ways for the commercial production of lime is described. Crushed —6 mesh limestone is dried and dedusted in a single bed reactor, then calcined in a 5-stage reactor. Construction, operation, and results obtained with both processes are given. THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,' showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.' Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime- stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a -in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontallv at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1953

By H. I. NORTON, H. O. Hofman

ZINC smelters in the central western. States have established a very high standard of purity for blende-concentrates, viz., zinc 60, iron less than 3, and lead less than 1 per cent. The very low percentage of iron is made possible by the blende containing less than 0.5 percent of isomorphous iron sulphide and by the sparing occurrence of pyritic material in the large blende-deposits of southwestern Missouri and southeastern Kansas. The blende in these districts occurs in sub-Carboniferous limestone, and is associated with chert, residual clay, calcite, pyrite or rnarcasite and bitumen. The different minerals are coarse and therefore readily separated by mechanical washing from the blende, with the exception of pyrite and marcasite, as blende has a specific gravity of from 3.9 to 4.1, marcasite, from 4.85 to 4.90, and pyrite, from 4.95 to 5.10. The common procedure of dressing the ores is to crush in a breaker, size in a trommel with 0.5-in. holes, pass the over-size through roughing-rolls and then jig the ore, now reduced to 0.5 in. maximum size, in roughing multiple-sieve jigs. The products of these are waste-tailings, sine-discharge coarse concentrates, side-discharge coarse middlings and bottom-discharge fine middlings. The coarse concentrates are sent to the market. The coarse middlings are crushed in middlings-rolls and brought back into the system by feeding into the main trommel. The fine middlings are cleaned upon finishing-jigs. Any pyrite or marcasite present follows the blende and increases the percent-

Mar 1, 1905

By C. Ernest Birchenall, Gerd M. Rosenblatt

The pressure and molecular weight of the antimony vapor over solid solutions of tin in antimony, containing 97.4, 94.9, 93.0, and 90.7 at. pct Sb, have been measured from 445° to 545°C by the torsion-effision method. The vapor is all Sb, within experimental error. A solidus curve which differs somewhat from the accepted curve has been calculated using the measured antimony activities. Metallographic examination of additional annealed alloys substantiates the accepted solidus. The solid solutions, which show negative deviations from ideality, probably do not deviate greatly from regular solution behavior. HANSEN' considers the Sb-Sn phase diagram to be well established with the exception of the boundary of the (Sb) phase.* Although there have been no pre- Their data can be combined with data for the solid alloys to calculate the solidus curve of the (Sb) phase. This paper presents measurements of the pressure ant1 molecular weight of antimony over Sb-Sn solid solutions containing 97.4, 94.9, 93.0, and 90.7 at. pct sb. Measurements were made by simultaneous use of the volmer3 torsion and Knudsen, effusion methods. The results of these measurements have been combined with the vapor pressure of pure antimony5 to obtain the activity of antimony in the primary solid solutions. The solidus curve calculated from these data differs somewhat from the accepted curve and is rather uncertain. Metallographic examination of Sb-Sn alloys was carried out to clarify the position of the solidus of the (Sb) phase. EXPERIMENTAL The apparatus and technique have been described previously.5 The measurements were made with the same effusion cells and torsion wire used in the measurements on pure antimony. The torsion measurements were calibrated with mercury at 30" using a mercury vapor pressure of 2.96 x 10-3 mm Hg determined by concurrent, absolute, weight-loss experiments. As in the measurements on pure antimony, an extraneous vapor was observed to distill off during the first run after the cell had been loaded with A fresh sample of alloy and during the first minute or two of every run. The change in composition after a series of runs with one sample was of the order of 0.1 at. pct and thus completely negligible in the calculation of the thermodynamic properties. The alloys were prepared from pieces of Merck antimony and Matheson, Coleman, and Bell reagent-

Jan 1, 1962

By W. O. Crosby

WASHINGTON CAMP, in Santa Cruz county, Arizona, is a small and little known mining district situated on the lower, eastern slope of the Patagonia mountains, about 20 miles east of Nogales and a like distance south of Patagonia Station on the Sonora railroad, which connects it Benson, 83 miles from Nogales, with the main line of the Southern Pacific. This district is also about 4 miles north of the international boundary, 35 miles west of Bisbee and 40 miles north of Cananea, in Sonora. The topography of the district, which lies at a general elevation of 5,500 ft. above the sea, is only very moderately rugged, and presents no obstacles to mining operations. Although some of the claims of the camp, including the Pride of the West, Belmont and Holland, were extensively worked for silver 25 years ago, they passed, at moderate depths, as in so many other districts, out of the argentiferous lead carbonate and sulphide into zinc, copper and iron sulphides; and for two decades the camp was abandoned and almost forgotten. In recent years, however, its apparent possi¬bilities as a copper producer have led to a revival of mining activity; but not, as yet, with conspicuous success. Although economically relatively unimportant, the deposits of Washington Camp are, mineralogically and structurally, nevertheless, typical examples of ore-bodies developed in connection with the garnet ledge now recognized as a normal feature of granite-limestone contacts; and, in the opinion of the writer, this is an instance where a minor example is yet essentially normal and capable of throwing important light upon the origin and genetic relations of the type.

Nov 1, 1905

By Corale L. Brierley

An unidentified, high-temperature microbe, which oxidizes reduced sulfur and iron in an acid medium between 45° and 75°C, is studied to determine its ability to leach copper sulfide minerals and molybdenite. Copper is leached from low-grade ore as well as a chalcopyrite concentrate, and preliminary data indicate a tolerance of 1.0 gpl copper by the microbe. A molybdenite concentrate is also biogenically leached, and the microbe is able to continue growth when the soluble molybdenum concentration is 750 ppm. Molybdenum can not be biogenically extracted from waste material using the present technique. Direct observation using SEM illustrates colonial growth and developmental characteristics of the microbe on molybdenite fines. The organism responds to hexavalent molybdenum by reducing this metal to the pentavalent state in aerobic and nitrogen gas atmospheres.

Jan 1, 1974

By J. J. Rutledge

I. DESCRIPTION OF THE CLINTON ORES AND ASSOCIATED POCKS. THE Clinton rocks in Stone Valley comprise (1) thick layers of deep-red shale, (2) layers of reddish-gray shale interspersed with beds of sandstone and thin beds of extremely fossiliferous limestone, and (3) yellowish-gray shales alternating with thin layers of olive-colored shales. These layers of shale are all very thin and are at no point massive.1 A bed of gray-white sandstone varying in thickness from 12 to 30 ft. occurs in the tipper portions of the Clinton shales. This is called the ore sandstone, a name given to it by Rogers and adopted also by the Second Pennsylvania Geological Survey. It is the surest guide to the presence of the iron-ore bed, which lies below its lower edges at distances varying from 10 to 20 ft. This ore sandstone, in the valley, lies generally at very low inclinations, but often is locally subjected to considerable changes in dip. At its outcrop this ore sandstone weathers very easily and yields a rather sparse crop of stone, Composed of dirty, iron-stained boulders. Upon the roads these boulders are quite well rounded, and bear fragments of crinoid stems and other fossil forms. The ore sandstone exhibits at many points evidences of former movements in this very great thickness of the shales, and as it is the only stratum in this series competent to transmit and record stresses due to structural movements, its evidence is of considerable importance in determining the occurrence of movements in times past.

Nov 1, 1908

By James J. Bean

Although determining and controlling specific gravity of operating medium in a heavy-media plant manually presents no problem, there are advantages to automatic recording and control. The two installations discussed employ the usual method of measurement. Pneumatic control with band control and reset features is used to regulate dilution water and hence specific gravity. Difficulties have been mechanical in nature and associated with obtaining a proper I sample and maintaining tight air connections in bubble-tube piping:

Jan 1, 1950

By G. S. Ansell, J. Weertman

The creep behavior of an aluminum alloy hardened with a finely dispersed phase of aluminum oxide was investigated. The as-extruded alloy shows an approximate steady-state creep in which the creed rate depends exponentially on the applied stress. The activation energy of creeb is abbroximately 150,000 cal per mole. The recrystallized alloy shows no steady-state creep. ONE method of improving the creep resistance of a metal is to introduce a finely dispersed second phase into the metal matrix. The improvement of the creep resistance has been qualitatively explained by assuming that the dispersed second-phase particles act as obstacles to dislocation motion. If the main effect of second-phase particles is simply to hinder dislocation motion then it is possible to derive a high-temperature creep equation for a dispersion-hardened alloy in a straightforward manner. In the Appendix of this paper such an equation is derived from a creep model which works very well for pure metals. Recently, F. V. Lenel has fabricated, for the first time, powder extrusions of aluminum-aluminum oxide in a large-grained recrystallized form. This alloy, designated as MD 2100, consists of a fine dispersion of aluminum oxide plates in a matrix of commercial purity aluminum. A considerable amount of investigation has been carried out concerning the microstructure and physical properties of this alloy.&apos; ) The aluminum oxide is present in the form of flakes 130A units thick and 0.3 u on edge. They are dispersed in the aluminum matrix with an average spacing of approximately 0.5 jx. The spacing varies in the range of 0.05 to 1.5 µ. The alloy structure is extremely stable at high temperatures. For this reason the alloy offers a unique opportunity for a fundamental study of creep of a very finely dispersed two-phase alloy. Lenel supplied specimens in both the unrecrystallized and recrystallized condition. This paper reports high-temperature creep experiments carried out on these specimens. The results obtained were rather unexpected. No steady-state creep was observed in the recrys-tallized material. In fact, after some transient creep which takes place upon loading, the creep rate is essentially zero ( < 10-8per min). If the second-phase particles acted solely as obstacles to the motion of dislocations, measurable steady-state creep would be expected. Since none is observed it appears that the main effect of the fine dispersion in the recrystallized material is to inactivate the dislocation sources themselves, rather than hinder the motion of dislocation loops created at these sources. EXPERIMENTAL DETAILS Specimens were tested in wire form, 0.087 in. in diam for the as-extruded alloy, and 0.035 in. in diam for the recrystallized alloy. These samples were held in friction-type wire grips; a gage length of 2.5 cm was used for all the creep tests. The specimens were held at 600°C in the test apparatus for at least 15 hr prior to each test. The tests were run under the condition of constant loading and, since the creep strains were small, can be considered as constant stress tests. The temperature of testing was held constant within 3°C. Elongations were measured with an optical cathetometer which was capable of measuring strains as smaIl as 0.00012. This allowed the measurement of strain rates as low as l0-8&apos;per rnin. In addition to the creep tests optical micrographs were made in order to determine both the grain size and microstructure of these materials. RESULTS Fig. 1 shows a few typical creep curves obtained from the as-extruded material. The elongations were somewhat erratic, but each curve shows a region of quasi-steady-state creep from which an approximate steady-state creep rate can be obtained. In general the higher the stress at a given temperature, the greater the total elongation before fracture. The lower the applied stress, the longer is the region where the creep rate is almost constant. Summary data from the creep tests of the as-extruded material are listed in Table I. The steady-state creep data of the as-extruded material for a range of stresses at a constant temperature follow a creep equation of the type creep rate = K&apos; = A exp (&) [11 where A and B are constants, k is Boltzmann&apos;s constant, T is the absolute temperature, and a the stress. The standard error of estimate of the data received is less than one order of magnitude. As shown in Fig. 2, if one compensates the creep-rate data for the effect of temperature over the range of test temperature, the steady-state creep data roughly follow a creep equation of the type Temperature compensated creep rate = K* = A exp

Jan 1, 1960

By J. D. Price, W. M. Bertholf

One of the chief difficulties with which the operator of a coal washing plant has been forced to contend is the handling of the very fine coal. First he has the problem of separating the fine coal from washery water. This is usually accomplished by the use of settling cones or Dorr thickeners: in either event the separated fine coal contains a high amount (40 to 80 pct) of water and, somewhat loosely, dependent upon the size of the coal particles present, may be known as sludge or slurry. His second problem is the satisfactory further dewatering of such separated sludge and/or slurry. At the coal washing plant of the Colorado Fuel and Iron Corp., washed coal from the Deister Plat-O tables is sluiced to a stationary inclined de-watering screen provided with 3/16 by 1-in. slots, and the coarse coal passing over this screen is conveyed by a Baum-type elevator and a flight-type distributing conveyor to a battery of Carpenter centrifugal driers. The fine coal and water passing through the openings of the primary dewatering screens, plus the fine coal passing through the screens of the centrifugal driers (and no small portion of which is the result of the disintegrating action of these driers) is pumped to two 30-ft Link Belt settling cones. The sludge recovered as underflow from these cones was formerly dewatered on stationary screens having 1/16 by 1-in. slots and discharged on top of the coarse washed coal in the Baum drainage conveyor; but after a relatively few hours of op eration the circulating load of fine coal on this conveyor built up to a point where it became necessary to reduce the quantity of feed to the washing tables. The original arrangement of our coal washing and dewatering equipment is shown in Fig 1. In order to regain the loss in active throughput which had been caused by this circulating load, an installation of six vibrating filters was made during the year of 1936. This resulted in an increase in normal tonnage of washed coal from 1430 to 1750 tons per 8-hr shift, a gain of slightly over 22 pct. This increase in throughput has made a very substantial decrease in the " conversion cost" per ton of washed coal. Since the vibrators were installed, we have gained about 2,000,000 tons in production, compared to what would have been produced in the same number of shifts at the former rate. Putting it in slightly different form, we have saved in the past 12 yr the cost of 1400 operating shifts in the washery. Fig 2 shows the location of the vibrating filters as applied to the original flowsheet. It will be noted that the sludge from the bottom of the settling cones is passed through a distributing box and thence to the filters. The de-watered coal from the filters is de-livered to the conveyor receiving the dried coal from the Carpenter driers.

Jan 1, 1950

By G. W. P. Rengstorff, R. B. Fischer

A study was made of the effect of impurities on the bend ductility of cast molybdenum. High purity molybdenum was repared by re-melting under high vacuum. The ductility of "transverse-grain" specimens indicated that intergranular brittleness decreased with an increase in purity of the metal. THE production of as-cast molybdenum with high ductility at room temperature would make working of the metal easier and increase the usefulness of the as-cast metal. Furthermore, a .knowledge of the factors that influence the ductility of as-cast molybdenum might be applied to the problem of making fusion weldments having satisfactory room-temperature ductility. Individual grains of commercial as-cast molybdenum are slightly ductile at room temperature. However, the presence of carbides at the grain boundaries may cause the metal to fracture in a brittle manner. This behavior has been discussed.&apos; The amount and distribution of the impurities in as-cast molybdenum would be expected, from previous research on the metal, to have considerable influence on its ductility. Some effects of oxygen and carbon on the mechanical behavior of the metal were discussed by Parke and Ham,2 Woodside,3 and Zappfe. Landgraf, and Worden.4 Parke and Ham2 found that, if a sufficient number of molybdenum oxide particles were present at the grain boundaries, the intergranular cohesion was reduced to the extent that arc-melted molybdenum would rupture intergranularly during hot forging. They also found that if the oxygen content was less than 0.003 pct, the cast molybdenum was hot forgeable. It is suspected, however, that forgeable molybdenum may contain a small amount of oxide that could reduce the ductility of the as-cast metal at room temperature. Also, there is the possibility of the unfavorable distribution of other impurities having a detrimental effect on the ductility of cast molybdenum. The results of a study of the influence of purity on the room-temperature ductility of cast molybdenum are presented here. Vacuum Arc-Melting to Produce High Purity Mo One way of determining the effect of impurities on the ductility of molybdenum is to prepare and test metal as free of all impurities as possible. Accordingly, the present investigation was undertaken with this in view. Arc melting in high vacuum (less than 0.1 micron of mercury) was chosen as the method for reducing the impurities below the concentrations occurring in commercial molybdenum. Commercial arc melting of molybdenum is carried out at about 50 microns pressure. During the arc melting, carbon and oxygen in the metal react to form carbon monoxide. By virtue of the vacuum process, the partial pressure of carbon monoxide is maintained at such a low value that the reaction greatly lowers oxygen and carbon contents. An excess of at least 0.03 pct C is used in commercial arc melting to insure that the oxygen content will be below 0.003 pct. The excess carbon remaining after the deoxidation step forms carbides on freezing. Some of the carbides precipitate at the grain boundaries and, as will be shown, have an unfavorable effect on the room-temperature ductility. In the present work, only the small amount of carbon (0.003 pct) contained in the commercial powder-metallurgy molybdenum used for melting stock was present. Partial removal of oxygen from the melt probably occurred as the result of the volatilization of molybdenum oxides, or by distillation of oxygen at the high melting tem-

Jan 1, 1953

By R. E. Phelan

WHILE 1931 was a most important year in the history of Canadian copper smelting and refining, nevertheless, due to the low price of copper and the in- ability of the International Nickel Co. to market its full capacity of nickel. the production of both copper and nickel was considerably less than the total installed capacity for the production of these metals. IIY the nor- mal course of events, 1931 should have seen a great increase in the production. of both copper and nickel in Canada, because the large extensions to both the copper smelting plants and the copper and nickel refinery capacity, which had largely been completed in the year 1930, should be showing their effect.

Jan 1, 1932