Search Documents

By C. D. Rubert, W. J. Parton

LARGE quantities of fine anthracite with associated impurities are discharged with the waste water from the coal-cleaning plants in the Pennsylvania anthracite region. Furthermore, for many years this fine material has accumulated and formed silt banks. The difficulty of removing the impurities from the fine material and the lack of adequate markets are responsible for the waste of this material. In view of a larger demand for fine coal, mainly for pulverized fuel, the Lehigh Navigation Coal Co. Inc. decided to investigate the froth flotation process for recovery of fine coal from these waste solids. A test plant was constructed and operated for six months during 1942 in order to determine the practicability of recovering coal from the waste water of a cleaning plant (breaker) by froth flotation, and to obtain operating data for designing a commercial plant if the results were favorable. PRELIMINARY INVESTIGATION Before the pilot plant was constructed information was obtained by field and small-scale laboratory tests to serve as a guide in the design and operation of the pilot plant. Size and ash analyses of a representative sample of the material discharged in the wash water from a cleaning plant are given in Table I. [ ] The refuse content increases progressively as the size of the particles decreases. The larger particles (+35 m.) are low in ash content and could be marketed without cleaning. Since these solids are discharged from the breakers with 90 to 95 per cent water by weight, the first step in the recovery of the coal was that of reducing the quantity of water so that water in excess will not have to be handled. Furthermore, it was found that the removal of most of the minus 200 mesh high-ash material was desirable to permit the most efficient flotation of the coal. Classification tests were run and showed that a hydroseparator overflow rate of 12 ft. per hour was sufficient to eliminate much of the minus 200-mesh material while allowing the coarser material to settle and be thickened.

Jan 1, 1944

By C. D. Rubert, W. J. Parton

Large quantities of fine anthracite with associated impurities are discharged with the waste water from the coal-cleaning plants in the Pennsylvania anthracite region. Furthermore, for many years this fine material has accumulated and formed silt banks. The difficulty of removing the impurities from the fine material and the lack of adequate markets are responsible for the waste of this material. In view of a larger demand for fine coal, mainly for pulverized fuel, the Lehigh Navigation Coal Co. Inc. decided to investigate the froth flotation process for recovery of fine coal from these waste solids. A test plant was constructed and operated for six months during 1942 in order to determine the practicability of recover ing coal from the waste water of a a plant (breaker) by froth cleaning and to obtain operating data for designing a commercial plant if the results were favorable. Preliminary Investigation Before the pilot plant was constructed information was obtained by field and small-scale laboratory tests to serve as a guide in the design and operation of the pilot plant. Size and ash analyses of a representative sample of the material discharged in the wash water from a cleaning plant are given in Table. The refuse content increases progressively as the size of the particles decreases The larger particles (+35 m.) are low in ash content and could be marketed without cleaning. Since these solids are discharged from the breakers with 90 to 95 per cent water by weight, the first step in the recovery of the coal was that of reducing the quantity of water so that water in excess will not have to be handled. Furthermore, it was found that the removal of most of the minus 200 mesh high-ash material was desirable to permit the most efficient flotation of the cod. Classification tests were run and showed that a hydroseparator overflow rate of 12 ft. per hour* was sufficient to elimi-,late much of the minus 200-mesh material while allowing the coarser material to settle and be thickened,

Jan 1, 1944

By C. D. Rubert, W. J. Parton

Large quantities of fine anthracite with associated impurities are discharged with the waste water from the coal-cleaning plants in the Pennsylvania anthracite region. Furthermore, for many years this fine material has accumulated and formed silt banks. The difficulty of removing the impurities from the fine material and the lack of adequate markets are responsible for the waste of this material. In view of a larger demand for fine coal, mainly for pulverized fuel, the Lehigh Navigation Coal Co. Inc. decided to investigate the froth flotation process for recovery of fine coal from these waste solids. A test plant was constructed and operated for six months during 1942 in order to determine the practicability of recover ing coal from the waste water of a a plant (breaker) by froth cleaning and to obtain operating data for designing a commercial plant if the results were favorable. Preliminary Investigation Before the pilot plant was constructed information was obtained by field and small-scale laboratory tests to serve as a guide in the design and operation of the pilot plant. Size and ash analyses of a representative sample of the material discharged in the wash water from a cleaning plant are given in Table. The refuse content increases progressively as the size of the particles decreases The larger particles (+35 m.) are low in ash content and could be marketed without cleaning. Since these solids are discharged from the breakers with 90 to 95 per cent water by weight, the first step in the recovery of the coal was that of reducing the quantity of water so that water in excess will not have to be handled. Furthermore, it was found that the removal of most of the minus 200 mesh high-ash material was desirable to permit the most efficient flotation of the cod. Classification tests were run and showed that a hydroseparator overflow rate of 12 ft. per hour* was sufficient to elimi-,late much of the minus 200-mesh material while allowing the coarser material to settle and be thickened,

Jan 1, 1944

By Thomas V. Falkie, Robert Stefanko

Much has been said and written recently about the manpower problem in the mining industry. The coal segment of the industry has been scrambling to staff and man its companies and operations in order to accommodate the current boom, and there are some interesting side- lights and developments which deserve further attention from coal mining people. This column will deal with the manpower problem in general and the plight of the professional-the mining engineer-in particular. At this point in the game, it is desirable and perhaps necessary to ask ourselves if there really is a manpower problem and, if so, how serious it is. Suprisingly, there are varying and conflicting answers to this question. If we are talking about warm bodies, then in most mining areas there is no problem. If, however, we are talking about skilled or trained people-at all levels-there are apparently serious shortages, especially in the coal industry and in the U. S. Bureau of Mines. To define quantitatively the present and future need for mining professionals is a formidable task, to say the least. Without pretending that these figures are anything but an educated guess, we feel there is an immediate need for about 1000 mining engineers right now and a continuing need for about 300 mining school graduates per year (double last year's number) for the next ten years in order to take up the slack, provide for attrition and maintain a normal growth rate. Mining companies, large and small, are just now beginning to realize that the industry is undergoing a revolution, It is no longer possible to design, build and operate coal mines by the "seat of the pants." Production demands, the new health and safety law and the inevitable new legislation on surface mining will require more engineering, more planning and new technology. There are mine operators who need mining engineers and don't even know that they need them. This could mean rough going for the small operator. It surely means that there will be a trend toward increasing the ratio of technical to nontechnical employees and the ratio of technical employees to dollars of capital towards levels comparable with other highly mechanized industries.

Jan 1, 1971

By R. Clare Coffin

The production of oil in the Rocky Mountain district, including southeastern New Mexico, increased from 33,048,630 bbl. in 1930 to 34,325,163 bbl. in 1931. This increase was due to production in New Mexico, which exceeded the 1930 figure by approximately 5,000,000 barrels. Total production by fields is given in Table 1. Exploration during 1931 resulted in the discovery of a new oil-producing horizon in the Big Muddy field in Natrona County, Wyoming, and ' the discovery of a new gas pool in the Powder Wash structure, Moffat County, northwestern Colorado. Gas was discovered also in the Frontier sands of the Bunker Hill dome, Carbon County, Wyoming, but no test has yet been made by which to determine the significance of this discovery. All other exploration which resulted in increasing the known reserves of oil and gas in the district was confined to drilling in partly outlined fields where known limits of production were extended. During the year two major gas pipe lines were completed in western Montana, and one in southwestern New Mexico was extended into Arizona. One new project involving the marketing of natural gas from Wyoming fields included the conversion of an existing oil line to a gas line to serve towns in southeastern Wyoming and western Nebraska. Colorado The decline of 132,501 bbl. in the production of oil in the Colorado fields during 1931 from the figure of 1930 is due to the natural decline of existing wells, partly offset by the increased production in the Greasewood area. New exploration was limited largely to northeastern Colorado, where attempts were made to find oil in areas adjacent to the Grease-wood field. Powder Wash, Moffat County.—The Ohio Oil Co. is to be credited with the discovery of a gas field in the Power Wash structure in Moffat County, Colorado. The initial well drilled in sec. 5-11-97 encountered a sand at a depth of 2152 ft. which produced 34,188,000 cu. ft. of gas on an open-flow test. The rock pressure was reported as 630 Ib.

Jan 1, 1932

THE distinction btween price reduction as a re-sult of lowering of production cost and price re-duction through unrestricted competition cannot be made too clear, because they are often interwoven in actual experience. Take the whole population of a town whose principal industry is shoe manufacturing as a concrete example. If the manufacturer is able to cut his price per pair in half because he has found out how to make a pair at half the cost, he will com-monly let a number of his men go, because reduction in production cost usually results from substituting cheap mechanical energy for expensive human energy. These people will normally find other employment. The workmen who remain employed usually earn more in dollars than they did before, and in spending it give employment where there was less before. Mining companies that initiate considerable enter-prises in foreign lands where the economic level is low, and where most of the people are busily but in-efficiently engaged in raising enough food to support themselves and their families, often find themselves confronted with an acute labor problem. If any con-siderable number of workers leave the land to work in and about the mines, those left on the land cannot raise enough food to keep them all unless they are taught better methods of agriculture and provided with equipment that will enable them to produce more with less expenditure of effort. Add to this the fact that managers commonly find that the "natives," as our British cousins designate them, usually need more food and a better balanced diet than they have been accustomed to in order to show anything above the lowest order of efficiency in industrial work,. and it is clear that to make a new industry possible in what may be termed an economic province involves increas-ing the productivity, not only of those who are em-ployed in it, but of the whole social group. It has already been pointed out that the employ-ment of large numbers of men in automobile manu-facture is only possible because the others have in-creased their productivity enough to turn out every-thing else that is needed without the help of the auto-mobile workers.

Jan 7, 1928

By F. Lynwood Garrison

The future of the Witwatersrand depends upon the possibility of mining and milling profitably the large tonnage of relatively low-grade gold ores known to exist in that area. The problem must be solved if the existence of the gold-mining industry in South Africa is to be saved and continue. To show that this disaster may be avoided, or at least postponed for another decade or longer, the following official statement is of interest: "There is a fairly large area of possible orebody on the East Rand of whose value and depth from the surface we have some though not very accurate knowledge. There is a far larger area south of the Central Rand which probably carries much payable ore, but at depths that at present appear too great to mine. Finally, there is a narrow strip of country over 100 miles in length stretching south from the Rand to Klerksdorp and beyond, which may contain large ore-bodies. The Witwatersrand rocks outcrop over portions of this ground and in places conglomerates occur in it that carry small bodies of payable ore. There is reason to believe that conglomerates of the Witwatersrand system exist over all this strip, though they are for the most part covered by later sediments. It seems probable also that there are large blocks of payable reef in this belt, at any rate in the area that lies close to the present western limit of the developed mines. The structure in this neighborhood is however very complicated and to prove the orebodies will be both difficult and costly." Ores in the Witwatersrand It should be explained in this connection that the conglomerates mentioned here were originally old gravel beds now consolidated into bedded sedimentary rocks, very hard because strongly cemented with secondary silica. The gold exists in this cement and is rarely found in the pebbles composing the rock or bed called locally reef. It is important to realize that these gold deposits are beds; not veins as generally understood by mining engineers and geologists. In addition to these low-grade ore reserves we have also to consider the ore left behind in the old stopes of the upper levels near the surface,

Jan 1, 1931

By C. D. King

The advances in basic open-hearth practice which have occurred during the past decade have been principally in the direction of the physical development of larger units, decreased fuel consumption and increased length of furnace campaigns. However gratifying the economies which have resulted from these improvements are, it must be granted that like advances in chemical, physical-chemical and metallurgical knowledge pertaining to open-hearth practice would have added greatly to these already attained reductions in costs and it is the purpose of this paper to stimulate the discussion and study of these phases of cooperation and their relation to ingot yields. Definition and Calculation oF Losses In discussing basic open-hearth yields, the writer refers to the ingot yields obtained in the process of converting pig iron, scrap and ore to steel. In this conversion some scrap is produced. The difference between the total weight of ingots and scrap produced and the original metallic charge constitutes the loss. Basic open-hearth yields vary considerably, and while some of the divergencies can be explained metal-lurgically because of differences in slag analysis, proportion of pig charges, and character of steel made, there often remain differences that apparently do not readily disclose themselves. In reconciling yields by the usual accepted methods of calculation, one is often forced to evaluate large losses as ((unaccounted for." Such a system is prone to accept these large losses as inherent to the operat.ion and not, susceptible of appraisement and correction. It is obvious that if the ingot yield plus the scrap recovered subtracted from 100 per cent. determines the loss, a drop in yield may increase the loss or the scrap, and both contribute to a monetary loss. To be sure, one can subdivide these unaccounted for losses into various components, such as metallics in slag, free Fe in slag, spillage, etc., and thereby reduce the amount of losses considered as "unaccounted for." If empirical methods could indicate with some degree of accuracy all losses, however slight, the undetermined losses become appreciably smaller and resultant calculations will check actual

Jan 1, 1929

By W. F. Flanagan, D. H. Polonis, S. D. Dahlgren

Rotation diffraction patterns of Cu-4.84 wt pct Si polymystalline samples were taken during the course of isothel-ma1 affing of the suPersaturated a phase, a diffraction spots were obserzled to streak during the initial stages of aging, and this streaking was similar to the streaking of a spots observed earlier by Barvett with deformed super saturated samples of the same composition. Although it was suggested that stacking faults were the sole cause of styeaking in the deformed samples, the present study has shown that plates with one small crystallite dimension can also contribute to the streaking when there is lattice coherency across close-packed planes. THE decomposition of the supersaturated a phase in Cu-Si alloys has been reported to occur by means of both thermal and stress activation.1-4 According to the Cu-Si phase diagram,3 Fig. 1, the supersaturated a phase (fcc) is expected to transform during aging by the precipitation of the y phase. The results of earlier studies2,4 have indicated that metastable k phase (hcp with nearly ideal close packing) forms initially at temperatures below the eutectoid temperature, after which the k transforms to the a and y phases. Hof-mann et al.4 have proposed a metastable version of the phase diagram, showing the approximate boundaries for k formation below the eutectoid temperature. In view of the close-packed nature of both the a and k phases, it is essential to consider the role assumed by stacking faults in the transformation. Streaking effects have been reported by Barrett 1 in the rotating crystal X-ray patterns of strained Cu-Si alloys and were attributed to stacking faults rather than particle size effects. This deduction was based on the observation that streaks in the diffraction patterns did not occur tangent to the 220fee Debye ring. It is known that the atom movements involved in faulting leave some X-ray reflections unaffected while others are broadened,' and, in particular, it has been shown that faulting will not cause streaking of 220fee reflections tangent to the 220fee Debye ring as would be expected if all the reflections were broadened.' The formation

Jan 1, 1967

By Charles W. Eichrodt

So much has already been wimitten on this vast subject of ground movement and subsidence, and so many data collected and commented upon, that in this paper the author proposes to confine himself to the submission of some plans showing what has actually occurred in the mining of several of the orebodies which have come under his direction during the last 20 years or so at Rio Tinto, Spain. Some notes are added for the purpose of describing the plans. The author does not attempt to give his opinion as to the reasons why the subsidences have occurred in the manner in which they are found, but confines himself to giving as true a picture as possible of the movements that have taken place. Effects of Excavation on Ground Movement Broadly, the effects of excavations on the overhead or adjacent ground can be classified under three headings, as follows: 1. Ground movements due to excavations made from surface only, such as those made in opencasts where no excavations underlie them. The stability and strength of the ground to resist movement must determine the slopes. 2. Ground movements due to underground excavations only; i. e., where the surface is not removed. 3. Ground movements due to a combination of both; i. e., from excavations taking place from the surface for the purpose of stripping an orebody and recovery of the ore to a certain horizon combined with excavations being carried out below, at the same time, for the winning of the ore below the horizon at which mining by stripping or opencasting under the specific conditions is no longer economical. Nos. 1 and 2 represent independent and distinct problems and No. 3 is a combination, which presents results much more difficult of explanation. The accompanying plans and sections give examples of what has occurred under the three conditions. Unfortunately, the class of ground is not exactly the same in them all, but the difference is not greater than is generally encountered over districts of equal area. Excavations from Surface To illustrate No. 1 three cross-sections are shown, of excavations made for the stripping and excavation from three different orebodies

Jan 1, 1930

By A. M. Nicholas

WHEN attempting to lift mill pulp containing a considerable percentage of wolframite, in an ordinary bucket elevator, difficulty was encountered from the tendency of the tungsten minerals to settle, on account of their high specific gravity. Lifts not exceeding 20 ft. (6m.) could be accomplished without particular difficulty, because there was insufficient time for consolidation of the heavy minerals in the bottom of the bucket; but with higher lifts, the heavy tungsten minerals would settle so solidly that when the bucket turned over at the top of the elevator the contents could be only partially dumped. In this case it ,was necessary to lift the material a distance of 34 ft. (10m.); hence some means had to be adopted to prevent settling, at least to such an extent that the material could be dumped from the buckets. To reduce the carrying time to a sufficient extent would have required a belt speed of 475 ft. (144.7m.) per minute, which was not feasible. It was decided to try, by vibrating the belt about midway of its span, to keel) the material sufficiently agitated during elevation to prevent settling. Underneath the rising side of the belt was placed a 12-in. (30.48-cm.) idler pulley, 18 ft.-(5.5 in.) up in the total lift of 34 ft. The idler pulley was set eccentric by 3/4 in. (19 mm.) and it was hoped that the vibration thus imparted to the belt, running at a speed of 280 ft. (85 m.) per minute, would prevent settling in the buckets. It was found that the pressure of the belt on the idler, due to the small inclination of the elevator, was not sufficient to overcome sliding on the idler, and the agitation was insufficient to accomplish the desired purpose. The idler was then connected to the drive shaft of the elevator through an intermediate pulley, gearing down to a speed of 20 r.p.m., so that a positive vibration was imparted to the belt; this imparted enough motion to the belt to prevent settling and the contents of buckets clumped satisfactorily.

Jan 2, 1918

By W. R. Crane

While professiorlally engaged in the oil- and gas-fields of Kansas, in measuring the pressure and flow of gas-wells, and studying the phenomena attendant upon the production of both oil and gas, I noticed in the flow of gas a peculiar and interesting feature. That there are actual lines of flow in liquids (non-compressible fluids) discharged through an orifice, or a short section of pipe, is shown by the external shape of the discharge—the vena contracts. Such lines of flow are not observable in the discharge of gas from an orifice. It can hardly be questioned that they exist. That they are not apparent is probably due to the very small weight of the gaseous particles, which climinishes the momentum of their movement in a given direction, acquired before they issue from the orifice, and also to the expansion of the gases, which would exert a powerful influence in overcoming any such tendency in their flow. Gas flowing from an orifice, supplied by a large reservoir or blowing-engine, exhibits almost the reverse of what is noticed with liquids. Namely, the gas assumes the form of an inverted truncated cone, of large angle: with its apex-end at the orifice. (See BB, Fig. 1.) This external ahape assunled by the flow of gas shows, however, marked differences under varying conditions of volume and pressure. For instance, a large volume of gas under high pressure, flowing through a 2- or 3-in. pipe, as in the case of a natural gas-well, assumes a more definite conical form, the angle of which increases as the pressure falls. Moreover, outside of the well-defined inverted cone is a thin conical heath or zone of gas, A A, the angle of which is considerably greater than that of the main cone, and increases with +1UNIVERSITY OF KANSAS, LAWRENCE, KANSAS.

Jan 1, 1905

By V. F. Hollister, M. Bernstein

The Copaquire porphyry copper deposit lies in an island of pre-Upper Tertiary rocks surrounded by Quaternary and Upper Tertiary formations. The pre-Upper Tertiary appears to be a horst block in a typical basin-range setting. Major right lateral faults have been mapped within the range from Chuquicamata north to Copaquire. All of the major porphyry copper deposits known in the block (e.g., Quebrada Blanca, El Abra, Chuquicamata, and Copaquire) are on or are very close to one of these major right lateral shears. In the Copaquire district, an epizonal igneous complex with diorite, quartz diorite, quartz monzonite, and intrusive dacite (in that intrusive order) invade folded Jurassic shale. Mineralization appears spatially and temporally associated with the quartz monzonite porphyry and dacite. Alteration zoning shows two separate core phyllic (quartz-sericite-pyrite) zones within one large argillic (clay-pyrite) zone. A propylitic (chlorite) zone is peripheral to the argillic zone. No potassic zone has been recognized yet at the surface. The intrusive petrology together with the phyllic, argilic, and propylitic alteration zoning as well as the chalcopyrite-molybdenite ore mineralogy characterize this deposit as being typical of the Lowell and Guilbert model. Copper and molybdenum minerals appear to be most strongly developed in the phyllic zone, in either a breccia or a zone of veinlets and stockwork which trend dominantly northeast, conjugate to the district's largest fault, the Sulfato fault. The setting is basically similar to that found in some other porphyry copper deposits in this block, in that the ore body is a zone of veinlets which appear to be genetically related to movement on a major north-south trending right lateral fault. The presence of the major fault in each deposit, and the speculative hypothesis that paleo-subduction zone operated at the time of mineralization, suggest the possibility that mineralization took place when a major fault permitted escape to the surface of cal-calkalic magma generated in a subduction zone as proposed by Ericksen. A hypothesis such as that proposed by Ericksen explains the near linearity of porphyry copper deposits in Chile, since the source of calc-alkalic magma would exist at about the same distance from a paleo-trench throughout the length of the paleo-subduction zone.

Jan 1, 1976

By Frederic K. Bunton

The smelting plant of the British Columbia Copper Co. at Greenwood, B. C., now closed because of the decline in the price of copper due.to the European war, is of special interest to metallurgists for several reasons. It was successfully smelting in blast furnaces the lowest grade copper ore of all plants in America. In order to do so, it had to run at very hig~; efficiency, which necessarily required a large tonnage per square foot of hearth area, together with the minimum amount of labor and other costs. The furnaces smelted daily 2,250 tons of ore (6.62 tons per sq. ft. of hearth area), carrying 0.85 per cent. of copper, at a smelting cost of 81.18 per ton. The entire plant required 130 men to operate it and keep up repairs, showing a labor efficiency of about 17.5 Dons per man per day. In the present paper, the method of obtaining these results is shown. Most of the information contained in this description I obtained as Assistant Superintendent, during the two years preceding the present shutdown. Other sources of information to which I am indebted are: The British Columbia Copper Co., Ltd., by ALfred W. G. Wilson, in The Copper Smelting Industry of Canada; Greenwood Smelting Worlrs, by J. E. McAllister, Engineering and Mining Journal, vol. xci, pp. 1011 to 1015 (May 20, 1911); and Description of the Copper Smelter of The British Columbia Copper Co., by W. L. Bell, in Transactions of the Canadian Mining Institute, vol. xvi, pp. 151 to 154 (1913). II. Location and Connections The smelter of this company is about half a mile south of GreenGood, in the Boundary district of British Columbia, on the Columbia & Westerg branch of the Canadian Pacific Railway. It was originally built in 1900 by Paul Johnson, to handle 600 tons of ore a day in two small furnaces of 300 tons capacity; but in 1907 the old furnaces were torn out, the plant was remodeled, and three blast furnaces, 48 by 240 in. at) the tuyéres, were installed. In 1910, two of these were enlarged to 51 by

Jan 1, 1916

By D. J. Barrett, M. A. Sochocky

INTRODUCTION Summary of Factors Influencing Comminution Circuit Design The selection of an appropriate comminution circuit for a specific ore is one of the most important decisions in the design of a processing plant. The importance is related to the fact that the capital and operating costs for crushing and grinding plant generally represent, as is well known, the major portion of the plant costs. This chapter will, therefore, identify as many as possible of the factors which influence the selection of a comminution circuit. The number of factors which will have to be considered for any comminution project will depend, among other things, on the type of project. If, for example, the project is an entirely new mining development, then most, if not all, the factors identified will have to be analyzed. If the project is an expansion of a developed mining operation or if the new orebody is adjacent to a viable operation, then the existing operation will influence the choice of factors or design constraints which need to be considered. The existing infrastructure or supporting systems may be quite adequate to accommodate the requirements of any expansion or new development. Hence, those factors may not have to be considered. To cover, however, the widest spectrum of projects, the factors which have been identified in this chapter are those which will have to be considered for the most complex of projects, that of developing an entirely new mining operation. The range of factors is as broad as the range of different ore types. Thus, each development must be treated with individualized care. The most important step in the development is the analysis and understanding of the ore characteristics. The hardness of the ore, its abrasiveness, friability, moisture content, grade, mineralization including gangue mineralization, liberation size, chemistry, and other characteristics should be the first to be analyzed in the investigation. The next should be the determination of factors such as plant size, throughput, location, climate, accessibility, and availability of water. The selection of samples for initial bench scale work and bulk sampling (when needed) for further

Jan 1, 1982

By Thomas M. Drown

IN the course of some experiments on the analysis of pig iron, I heated, in a platinum crucible, some borings of a graphitic pig iron with sodium carbonate. When the crucible was at a full red heat and the carbonate was thoroughly fused, I noticed a lively ebullition of the mass, and an escape of gas, which burned on the surface. On investigation this gas proved to be carbonic oxide, and on examining the borings in the bottom of the crucible after an hour or two, they were found to be perfectly malleable, although unchanged in general form and appearance. Analysis showed that the carbon was completely removed. I then repeated the experiment, to ascertain whether the silicon and phosphorus were affected, and found that these elements too were largely removed, and could be found in the fused mass as alkaline silicates and phosphates. In order to ascertain whether the removal of the silicon and phosphorus was merely a surface action or whether the reaction really extended into the mass of the iron, I tried the following experiments : A number of bars of pig iron were cast about one foot long and planed down-accurately to one inch section. These were immersed in a large wrought-iron pot full of molten sodium carbonate made by fusing the commercial bicarbonate of soda. Through the kindness of Mr. Frank Firmstone, Superintendent of the Glendon Iron Works, Easton, I was enabled to keep this pot at a reasonably constant high temperature for a long time in one of the hot-blast ovens. One of the bars was removed from the pot every twenty-four or forty-eight hours, according to the rapidity of the action, and after cooling was broken and the fracture examined. The change from pig iron to malleable iron was progressively inwards and always sharp and easily recognized, the rate of progression being in a decreasing ratio with the time. The temperature of the oven had evidently

Jan 1, 1879

COLUMBIA SECTION STANLY A. EASTON, Chairman, FREDERIC KEFFER, Vice-Chairman, L. K. ARMSTRONG, Secretary-Treasurer, P. 0. Drawer 2154, Spokane, Wash. D. C. LIVINGSTON FRANK A. Ross The first meeting of the Columbia Section was held on March 24, as a part of the 1916 Northwest Mining Convention which was held under the -auspices of the Spokane Mining Men's Club assisted by the Spokane Chamber of Commerce, the technical program being in charge of the Spokane Engineering and Technical Association assisted by the local sections of the A. I. E. E., A. S. C. E., and A. I. M. E. The program of the successive sessions was carefully arranged with view to its application to mining, and in addition to the technical program there were exhibits of ores, minerals, devices, etc., of interest to the delegates, who numbered over 500. A portion of the program was also arranged with special reference to the requirements of the prospector and miner. A reception, a banquet, a complimentary luncheon, a regular daily call' of the Stock Exchange, a visit to the High Schools and to one of the substations of the Washington Water Power Company and to the Union Iron Works kept the visitors entertained, the ladies being looked after by a special committee of ladies who held open house during the entire week. Several important resolutions were passed by the Convention and one by the Columbia Section, A. 1. M. E. With Stanly A. Easton, chairman, presiding, the Columbia Section, American Institute of Mining Engineers, occupied the time between 2.00 and 5.30 p.m., March 24th, the Moorish room of the Spokane hotel being filled with members and their guests. "The Apex Law and the Mineral Surveyor" was a paper presented by F. W. Callaway and generally dis-cussed because of its local application in the Coeur d'Alenes, the conclusions being reached after expensive litigation between two of the large mining operators in that district.

Jan 6, 1916

By Thomas M. Drown

In the course of some experiments on the analysis of pig iron, I heated, in a platinum crucible, some borings of a graphitic pig iron with sodium carbonate. When the crucible was at a full red heat and the carbonate was thoroughly fused, I noticed a lively ebullition of the mass, and an escape of gas, which burned on the surface. On investigation this gas proved to be carbonic oxide, and on examining the borings in the bottom of the crucible after an hour or two, they were found to be perfectly malleable, although unchanged in general form and appearance. Analysis showed that the carbon was completely removed. I then repeated the experiment, to ascertain whether the silicon and phosphorus were affected, and found that these elements too were largely removed, and could be .found in the fused mass as alkaline silicates and phosphates. In order to ascertain whether the removal of the silicon and phosphorus was merely a surface action or whether the reaction really extended into the mass of the iron, I tried the following experiments : A number of bars of pig iron were cast about one foot long and planed down 'accurately to one inch section. These were immersed in a large wrought-iron pot full of molteu sodium carbonate made by fusiug the commercial bicarbonate of soda. Through the kindness of Mr. Frank Firmstone, Superintendent of the Glendon Iron Works, Easton, I was enabled to keep this pot at a reasonably constant high temperature for a long time in one of the hot-blast ovens. One of the bars was removed from the pot every twenty-four or forty-eight hours, according to the rapidity of the action, and after cooling mas broken and the fracture examined. The change from pig iron to malleable iron was progressively inwards and always sharp and easily recognized, the rate of progression being in a decreasing ratio with the time. The temperature of the oven had evidently

Jan 1, 1879

By H. C. George

The Wisconsin Zinc District, or the Upper Mississippi Lead and Zinc District as it is often called, lies in the southwestern corner of Wisconsin, in Grant, Iowa and Lafayette Counties, and it includes adjoining parts of Illinois and Iowa. The district is about 70 miles long, north and south, and about 40 miles wide, east and west. It lies wholly within what is geologically known as the non-glaciated area of the Upper Mississippi Valley. HISTORY OF THE DISTRICT The district was first opened up as a lead producer in 1822. From this time until 1860, about 205,000 tons of cog lead (galena) and washed lead (galena) was produced from shallow crevices and openings. From 1860 to 1900, about 74,500 tons was produced, and since that time, from 5000 to 7000 tons has been produced annually. Since 1900, most of the lead concentrate produced has been as a byproduct of the zinc mines. The first zinc ores were mined about 1862. These were the carbonate ores, locally known as "drybone." Very little zinc blende was mined in the district, previous to 1875. The zinc blende ores mined from 1875 to 1900 were mostly of the high-grade, hand-cobbed, sheet-ore class, which usually contained from 45 to 60 per cent. metallic zinc Such mines as the "Sallie Waters," "Quinlin," 'Lead Mine," "Benton Blende," and "Ida Blende," located near Benton, Wis., were mines which produced ores of this type, during this period. The mines located at Highland, the "Coker Mine" located at Livingston, Wis., and the "Opencut Mine" located at Shullsburg, Wis., were mines that were heavy zinc carbonate producers, previous to 1900. The production of zinc ores in the district from 1862 to 1890 was about 283,500 tons, mostly zinc carbonate, with a probable average metallic zinc content of 30 per cent. From 1890 to 1903, the production

Jan 1, 1918

By A. M. Nicholas

WheN attempting to lift mill pulp containing a considerable percentage of wolframite, in an ordinary bucket elevator, difficulty was encountered from the tendency of the tungsten minerals to settle, on account of their high specific gravity. Lifts not exceeding 20 ft. (6 m.) could be accomplished without particular difficulty, because there was insufficient time for consolidation of the heavy minerals in the bottom of the bucket; but with higher lifts, the heavy tungsten minerals would settle so solidly that when the bucket turned over at the top of the elevator the contents could be only partially dumped. In this case it was necessary to lift the material a distance of 34 ft. (10m.); hence some means had to be adopted to prevent settling, at least to such an extent that the material could be dumped from the buckets. To reduce the carrying time to a sufficient extent would have required a belt speed of 475 ft. (144.7 m.) per minute, which was not feasible. It was decided to try, by vibrating the belt about midway of its span, to keep the material sufficiently agitated during elevation to prevent settling. Underneath the rising side of the belt was placed a 12-in. (30.48-cm.) idler pulley, 18 ft. (5.5 m.) up in the total lift of 34 ft. The idler pulley was set eccentric by % in. (19 mm.) and it was hoped that the vibration thus imparted to the belt, running at a speed of 280 ft. (85 m.) per minute, would prevent settling in the buckets. It was found that the pressure of the belt on the idler, due to the small inclination of the elevator, was not sufficient to overcome sliding on the idler, and the agitation was insufficient to accomplish the desired purpose. The idler was then connected to the drive shaft of the elevator through an intermediate pulley, gearing down to a speed of 20 r.p.m., so that a positive vibration was imparted to the belt; this imparted enough motion to the belt to prevent settling and the contents of buckets dumped satisfactorily. Protecting Elevator Belts When elevating, from the crusher, a rock which was very sharp and abrasive, considerable difficulty arose from cutting of the belt under-

Jan 1, 1918