Search Documents

By W. H. Bassett, C. H. Davis

ALTHOUGH brasses and bronzes have been made for ages, a systematic study of their physical properties has been carried out only during the years of the present century. Among these properties may be included those which are to be detected by means of microscopic examination; in other. words by the science of metallography. The earlier workers in this field, both in this country and abroad, gave their attention to steel. When the senior author explored the situation in 1902, there was little encouragement to be found in undertaking the study of the non-ferrous alloys. A start was made, and the metallography of the brasses and bronzes, as well as of the copper-nickel-zinc alloys developed materially under his direction. Annealing experiments were begun in 1902, and in the succeeding years the effect of temperature, and the influence of previous working, on the grain size of brass were studied. The conclusions so well known and widely published today were largely reached during those earlier years. . In 1905 the first complete annealing series were made. By this it is meant that brass and copper sheet, 5 B & S Nos. hard, was machined into tensile test specimens, then annealed under accurate control for 30 min. at temperatures up to the melting point of the material. Various determinations were made, including tensile strength and elongation in 2 in. There rapidly followed similar series on all of the copper-zinc alloys from 100 to 60 per cent. copper, on the bronzes, cupronickels, and on copper-zinc-nickel alloys. At this point there was published by Grard, in October, 1909,1 the very comprehensive and complete work on the tensile properties of cartridge brass, 90-10 copper-zinc, and electrolytic copper. The excellent photomicrographs in that paper illustrated the changes in structure produced by cold rolling as well as by annealing at different temperatures, but where Grard's work was confined to copper and to two alloys, the investigations in this laboratory have been over the entire fields of the commercial copper-zinc alloys, copper-tin alloys, representative copper-nickel and copper-nickel-zinc alloys as well as aluminum bronzes and others of a more special nature.

Jan 1, 1928

By W. H. Bassett

ALTHOUGH brasses and bronzes have been made for ages, a systematic study of their physical properties has been carried out only during the years of the present century. Among these properties may be included those which are to be detected by means of microscopic examination; in other words by the science of metallography. The earlier workers in this field, both in this country and abroad, gave their attention to steel. When the senior author explored the situation in 1902, there was little encouragement to be found in undertaking the study of the non-ferrous alloys. A start was made, and the metallography of the brasses and bronzes, as well as of the copper-nickel- zinc alloys developed materially under his direction. Annealing experiments were begun in 1902, and in the succeeding years the effect of temperature, and the influence of previous working, on the grain size of brass were studied. The conclusions so well known and widely published today were largely reached during those earlier years. In 1905 the first complete annealing series were made. By this it is meant that brass and copper sheet, 5 B & S Nos. hard, was machined into tensile test specimens, then annealed under accurate control for 30 min. at temperatures up to the melting point of the material. Various determinations were made, including tensile strength and elongation in 2 in. There rapidly followed similar series on all of the copper-zinc alloys from 100 to 60 per cent. copper, on the bronzes, cupronickels, and on copper-zinc-nickel alloys. At this point there was published by Grard, in October, 1909,1 the very comprehensive and complete work on the tensile properties of cartridge brass, 90-10 copper-zinc, and electrolytic copper. The excellent photomicrographs in that paper illustrated the changes in structure produced by cold rolling as well as by annealing at different temperatures, but where Grard's work was confined to copper and to two alloys, the investigations in this laboratory have been over the entire fields of the commercial copper-zinc alloys, copper-tin alloys, representative copper-nickel and copper-nickel-zinc alloys as well as aluminum bronzes and others of a more special nature.

Jan 1, 1927

By W. H. Bassett, C. Davis

Although brasses and bronzes have been made for ages, a systematic study of their physical properties has been carried out only during the years of the present century. Among these properties may be included those which are to be detected by means of microscopic examination; in other words by the science of metallography. The earlier workers in this field, both in this country and abroad, gave their attention to steel. When the senior author explored the situation in 1902, there was little encouragement to be found in undertaking the study of the non-ferrous alloys. A start was made, and the metallography of the brasses and bronzes, as well as of the copper-nickel-zinc alloys developed materially under his direction. Annealing experiments were begun in 1902, and in the succeeding years the effect of temperature, and the influence of previous working, on the grain size of brass were studied. The conclusions so well known and widely published today were largely reached during those earlier years. In 1905 the first complete annealing series were made. By this it is meant that brass and copper sheet, 5 B & S Nos. hard, was machined into tensile test specimens, then annealed under accurate control for 30 min. at temperatures up to the melting point of the material. Various determinations were made, including tensile strength and elongation in 2 in. There rapidly followed similar series on all of the copper-zinc alloys from 100 to 60 per cent, copper, on the bronzes, cupronickels, and on copper-zinc-nickel alloys. At this point there was published by Grard, in October, 1909,' the very comprehensive and complete work on the tensile properties of cartridge brass, 90-10 copper-zinc, and electrolytic copper. The excellent photomicrographs in that paper illustrated the changes in structure produced by cold rolling as well as by annealing at different temperatures, but where Grard's work was confined to copper and to two alloys, the investigations in this laboratory have been over the entire fields of the commercial copper-zinc alloys, copper-tin alloys, representative copper-nickel and copper-nickel-zinc alloys as well as aluminum bronzes and others of a more special nature.

By Stephen Taber

A vein may be defined as an aggregation of mineral matter, more or less tabular or lenticular in form, which was deposited from solution and is of later origin than the inclosing rock. This definition differs from the one found in many text-books in that no assumption is made as to the origin of the space occupied by the vein or the manner in which the mineral matter was deposited. In the present paper the writer purposes to discuss the mechanics of vein formation, and does not wish to begin by begging the question. The origin of ore deposits has been diligently investigated in recent years, but, while much has been written concerning the chemistry of the process, the physical side of the question has received less attention. The source of the ore minerals; the chemical composition of ore-bearing solutions; the relative importance of magmatic and meteoric waters as agents of concentration; and the causes of mineral precipitation have all been discussed at length. On the other hand, little has been written concerning the mechanics of vein formation, and the theories given in text-books today are essentially the same as those developed by the early Cornish and Saxon miners. Early investigators often regarded both veins and dikes as igneous in origin, but today the theory that vein minerals have been deposited from solutions, either liquid or gaseous, is firmly established. The latter view is supported by the fact that many vein-forming minerals are not found in unaltered igneous rocks; by evidence obtained in the laboratory regarding the solubility of minerals; by the presence of many ore minerals in hot-spring waters; by the occurrence of some veins in regions consisting exclusively of unaltered sedimentary rocks; by evidence as to the temperature at which some minerals are formed; and by the absence of mineral segregation due to difference in specific gravity. There is still, however, much difference of opinion as to whether certain tabular-shaped masses should be classed as veins or as dikes. Some of the earlier investigators have also advocated the theory that veins are contemporaneous in origin with the inclosing rock, while others have believed the vein minerals to represent a recrystallization or transforma-

Jan 1, 1920

ASHBEL WELCH, LAMBERTVILLE, N. J.: Dr. Dudley has given the wear of steel rails under four different conditions. He arrives at the conclusion that the softer rails, or those that from their composition ought to be softer, wear better than the harder. But there is another condition which has an important bearing on the subject, and, should not be overlooked,-the weight on a wheel. With the lighter weights of the past, the softer rails may have worn best; with the heavier weights of the future, the harder may wear best. Weights will probably be increased up to the capacity of steel to bear; then doubtless the harder steel will wear best. A leaden rail with ten pounds on a wheel might carry millions of tons, but with one hundred pounds on a wheel, it would be destroyed by a few thousand tons. So in the days of iron rails, my experience was that the softer rails under light machinery stood better than some of the harder; but under heavy machinery the softer were much the most rapidly destroyed. His doubtless the same with steel. The pounding motion of the wheels loosens or spreads the particles of a thin film of steel; the pull lengthwise on the rail de- * Metallurgical Review, vol. i, page 1. † The remarks as here given, as in the previous discussion on steel rails, have all been written out or revised by the participants in the discussion, and represent, therefore, their mature views. It has been thought that this plan, when it can be carried out without doing any of the speakers injustice in debate, is much to be preferred to a strictly verbatim report. The remarks of Mr. Chanute were sent to the secretary after the. meeting, and although they did not form a part of the actual discussion, there can be no doubt of the desirability of including them in this report. The papers under discussion were “Rail Specifications and Rail Inspection in Europe,” by C. P. Sandberg ; " The Wearing Capacity of Steel Rails in Relation to the Chemical Composition and Physical Properties," by C. B. Dudley, and a Rail Patterns," by A. L. Holley. T. M. D., Secretary.

Jan 1, 1881

By Charles A. Ashburner

One of the most unexpected and unusual mining disasters which have ever been recorded in the Pennsylvania anthracite region, or, in fact, in any coal-mining district, occurred in the northern anthracite field near Nanticoke, Luzerne County, about 10 o'clock on Friday morning, December 18, 1885. This accident caused the death of twenty-six persons, a larger number than had perished in any catastrophe in the anthracite mines since that which occurred at the West Pittston mine in 1871. The Nanticoke disaster resulted from a " cave-in " in the roof of a portion of the Ross coal-bed workings from Slope No. 1 of the Susquehanna Coal Company, by which a large body of quicksand, gravel, rock- and coal-boulders, and water broke through the roof of the mine, filling up a large extent of the workings, until not only the water, but also the rock material, flowed out at the mouth of the mine. Immediately over the point where the "cave-in" occurred, was located a large pile of refuse coal and slate, taken from Slope No. a. After the occurrence of the accident, I made a very careful examination of the ground in the vicinity of the "cave-in," in conjunction with a study of all the maps, sections and other mining data in the possession of the Susquehanna Coal Company, which were placed at my disposal by Manager Irving A. Stearns. The accompanying map, Fig. 1, was compiled from the Company's map, and from special maps made by the Geological Survey under the direction of my assistant, Mr. Frank A. Hill. This map shows the relative position of the mine-workings, the surface features and the "cave-in," and other points to be specially referred to hereafter. My examination was made particularly with the view of determining the indirect cause of the " cave-in," and the local geologi-

Jan 1, 1887

By B. B. Cox

The Iraq Petroleum Company, Ltd. continued its systematic exploration and exploitation of the Kirkuk field on a unitized basis. Pressures, gas-oil ratios, oil-water level and oil-gas level remained satisfactory. All wells were produced by flowing and more than two-thirds of the crude was stabilized. The only exports from Iraq during 1937 were from the Kirkuk field. Mosul Oilfields, Ltd., through its operating subsidiary, the British Oil Development Company, Ltd., inaugurated an exploratory program to find lighter oil than the heavy, black, sulphurous reserve proved in the Qaiyarah-Najmah-Jawan-Qasab field. Deeper drilling in this field found a small reserve of 17" to 19" A.P.I. black sulphurous oil in the Pilsner (Upper Cretaceous). Ten structures outside the proved field were tested or were under test at the end of the year. In spite of this intensive program no reserve of lighter oil was discovered. The reserve at Qaiyarah-Najmah-Jawan-Qasab averages 16" A.P.I. with 6+ per cent sulphur from the "continuous limestone" (Lower Miocene, Oligocene, Middle Eocene) and from the Pilsner (Upper Cretaceous). The Khanaqin Oil Company, Ltd., a subsidiary of the Anglo-Iranian Oil Company, Ltd., conducted the normal exploitation of its Naft Khaneh oil field and supplied the local Iraq market requirements. Slightly more than 31,600,000 bbl. of crude was produced in Iraq during 1937. The following table gives the total crude produced by the I.P.C. for export during the last four years. Year 42-gallon BarreL Increase over Preceding Year 1934 7,096,669 1935 27,014,904 19,918,235 1936 29,521,053 2,506,149 1937 31,171,476 1,650,423 " Converted at an average of 7.6 bbl. per ton. Published by permission of the Near East Development Corporation. Manuscript received at the office of the Institute March 11, 1938. * Geologist, Socony-Vacuum Oil Co., Inc., New York, N. Y.

Jan 1, 1938

By R. Ward Grosz

The Robinson mining district in east-central Nevada is itself a century of study in the changing economics of the mining business. It began as a boom and bust area. In the district today, just west of Ely, Nev., the hills are pockmarked with the tunnels and shafts sunk in a frantic scramble for gold and silver before the turn of the century. But as the economics of dwindling reserves, rising costs, and changing markets were stamping out the efforts of the gold and silver seekers, copper took over as the king of the Robinson district. Today, Kennecott Copper Corp. has four open pit mines in the district and is planning a fifth. From these mines, Kennecott produces nearly 40,000 tpy (tons per year) of copper. In its hundred years of history, the district has produced more than $1 billion in mineral values, a richer treasure than that from the more famed Comstock Lode of Virginia City, Nev. Prospectors had reported copper outcroppings in the Robinson district as early as 1872. But the first significant copper orebody was not discovered until 1901. In that year, Dave Bartley and Edwin Gray exposed the top of the porphyry orebody that would become the Ruth mine in a shaft at a depth of 120 ft. Subsequently, other larger orebodies were discovered nearby which have resulted in this area being one of the leading copper producers in the country for some 60 years. Following a period of development and exploration, the Ruth mine started production in 1915 and continued as a prosperous underground mining operation until 1948. The mining industry in Nevada experienced the same increasing cost of labor and supplies that all other mining areas had to contend with, and by 1948 the Ruth mine was no longer profitable. The mine was closed down on August 8 of that year. Now, two decades later, the mine is to produce again. The key factor in the case history of

Jan 1, 1969

By Waldemar Lindgren

During the last 15 years much attention has been given to the " contact-metamorphic" ore deposits which mainly occur in limestone close to intrusive contacts. In general, these deposits are characterized by the association of magnetite and simple sulphides with the so-called L'contact-metamorphic" silicates. These silicates comprise garnet, epidote, vesuvianite, tremolite, wollastonite, diopside, hedenbergite, ilvaite, and many other rarer forms. The contact-metamorphic zones contain also in places minerals with boron, fluorine, and chlorine, like axinite, tourmaline, danburite, fluorite, and scapolite. There is also more or less quartz and coarsely recrystallized calcite. The simple sulphides embrace pyrite, pyrrhotite, chalcopyrite, galena, zincblende, more rarely arsenopyrite. On the whole, sulphantimonides and sulph-arsenides are rare. Deposits of magnetite or chalcopyrite or of both are most common. The deposits have an irregular or rudely tabular form, following main contacts, dike contacts, or stratification planes; they rarely extend for more than 1,500 or 2,000 ft. from the contact; far more commonly they only reach a distance of a few hundred feet from that surface. The deposits are usually formed by replacement of limestone, or allied calcareous rock. Apparently they are found both in relatively pure and in impure carbonate rock. The deposits are geoiogical bodies of a chemical and mineralogical character differing greatly from the adjoining intrusive rock and from the unaltered limestone. They are rich in silica and iron, with more or less of lime, magnesia, alumina, sulphur, and rarer metals like copper. The so-called contact-metamorphic silicates which form the gangue usually are coextensive with the metallic minerals, though of course not necessarily with the merchantable ore. All opinions agree in holding the deposits of epigenetic origin, later than the inclosing limestone. Regarding the origin of the metals and the genesis of the ores there are several opinions. 1. There are those who see in these deposits the result of concentration of material contained in the intrusive rocks by means of hot circulating

Jan 1, 1915

By H. H. Power, C. H. Pishny

When an oil operator becomes a party to a proration agreement he may wonder, with good cause, whether production prorated .today is merely deferred until tomorrow or whether oil might be lost. Various types of evidence obtained from production records when studied quantitatively are of great assistance in arriving at definite conclusions. A study of individual examples cited in this paper leads towards some solution of the problem, particularly when they are considered in the aggregate. Many production curves on various pay horizons were studied. A disappointingly large number of these were of contributory value, but inconclusive. However, there were enough curves of similar type from the Wilcox sand at Earlsboro, Bowlegs, Seminole City, the Cromwell horizon at Little River, and the Simpson dolomite at Valley Center, Kansas, from which reasonably definite conclusions were drawn. Assuming that deferred production is later made up with no increase in ultimate recovery, a curve (Fig. 1) shows the normal flowing and pumping life of a composite well, contructed by the family curve method. The initial production of the well shown is 1700 bbl. daily and the allowed production is 25 per cent. On this basis the average daily allowed rate for the first month is 425 bb1., or the area BCDE, which is equivalent to the area AFDG under the normal decline curve. The potential production for the second month is 1500 bbl. and the allowed production 375 bbl. daily. By this procedure a potential curve for each succeeding month is obtained (points A, H, I, J and K). If the well is opened it should produce somewhere near its potential curve for a short period and then decline at a more rapid rate than the potential curve. This theoretical analysis is basic. Actual examples exhibiting all points raised by the ideal curve are rare. Proration in the Mid-Continent area has been effected mostly by leases rather than by individual wells; hence a well may produce any

Jan 1, 1931

By M. J. Sinnott, J. C. Tobin

A technique for collecting and analyzing the small quantities of gases desorbed on heating metal powders has been developed. The gases collected from copper powders of various types of manufacture have been analyzed and found to contain H2O, CO2, and SO2. The quantities of gas evolved vary from 0.05 to 1.0 milliliter, under standard con-ditons of temperature and pressure, per gram of powder. The source of the gas has been traced to surface films on the powder. IN the powder-metal industry it is recognized that the presence of gases in the powders affects the processing and resulting properties of the sintered product. Several sources for these gases are possible; namely, chemical reactions with the sintering atmospheres, inclusion. of gases during compacting, dissolved gases in the metal powder, and sorbed gases on the metal-,powder surfaces.1, 2, 3 Since the quantities of the gases are relatively small, no direct attempt has been made to collect and analyze them nor to isolate their source. The work that has been done has been concerned with the dimensional stability of the product., its porosity, density, or mechanical and physical properties. Conclusions are drawn on the basis of studies of this type as to the probable effect of gases on these properties. 4, 5, 0 In the present investigation an attempt has been made to obtain quantitative data on the analysis and quantities of gases associated with copper powders manufactured in different ways. Apparatus was constructed to collect gases evolved from loosely packed powder samples on heating to various temperatures under a reduced pressure of helium. The powders were outgassed thoroughly in a vacuum prior to starting the collection operation in order to eliminate mechanically entrapped gases and to prevent the possible reaction of the powder with these gases. Experimental Procedures Materials—The major portion of the investigation was carried out on a single heat of water-atomized, oxygen-free, high-conductivity copper. A relatively coarse fraction of this powder, 20 to 100 mesh, was tested as a mixed powder and as various graded size fractions. The microstructure of this powder showed equiaxed grains and was clean and free from oxides and oxide eutectic. The particle size, as determined

Jan 1, 1959

THE strike of the coal miners began on April 1, as had been expected, the entire force of unionized miners-both anthracite and bituminous-going out and making this the most widespread strike of record. Up to the present writing there has been no serious inconvenience to industry in general, the accu-mulated stocks of coal being large and the non-union mines having continued to make a substantial production. However, the union labor leaders, having concentrated their efforts toward inducing the non-union miners to go out also, met with some measure of success in certain fields and created a shortage of coking coal, which caused iron makers to bank a few furnaces. The strike of textile workers in New England spread further. Here and there, throughout the country there were sporadic troubles with the builders. Rail-way labor was the subject of continued palavers, which did not get anywhere. On the whole the events of April were in line with the forecast that this would be a year of labor troubles. In domestic politics, the soldier bonus bill, having been passed by the House, went to committee consider-ation in the Senate. Public opposition to it manifestly waxed. On the floor of the Senate the tariff bill was under consideration and is drawing nigh to passage, without there being much consideration of its probable economic consequences. It is going to be a very high tariff and there is much in it that is equivalent to subsidizing small and normally unprofitable industries at the expense of the people as a whole. Abroad affairs were more quiet, superficially at least; than they were in March. In Egypt, India and South Africa things calmed, down, so far as we know, but in Ireland there was continued turmoil. The Irish, having won their freedom to the same degree as the Canadians, have entered upon violent quarrels among themselves, more over phrases than anything .else, so far as we can see. Lloyd George obtained a spectacular vote of confidence from Parliament and thus postponed, the exigency of a general election.

Jan 5, 1922

By E. L. Davis

There have been many attempts to devise formulas for flowing efficiency and flow friction of oil-gas mixtures in oil-well flow tubes. Actually, however, flowing efficiency is rarely any real concern of the oil producer and flow-friction formulas contain so many unknown variables as to be of little, if any value. The production engineer is generally concerned with producing as much oil as possible with a minimum expense per barrel, and with the lowest possible net gas-oil ratio. These ends frequently are opposed to each other and the gas-oil ratio usually is sacrificed. In competitive operations, such as in town-lot fields, high current production is the sole interest. In conservative operation the greatest possible amount of oil obviously should be produced by natural flow unless the net formation gas-oil ratio can be improved by circulating gas. In practice this condition frequently exists. It would be a great advantage if the flowing condition of a well could be analyzed to determine the best possible producing status. Anticipating the death of a well so that gas-lift could be started immediately after the death, or preferably before, would save both production and expense. Frequently it happens that circulating gas fails to help a flowing well, or will not flow it after it has stopped flowing naturally. A knowledge of the laws governing flow would save considerable expense in testing such cases. A predetermination of probable pressures and amounts of circulating gas needed to flow wells and give best possible producing conditions would help in designing compressor installations. The optimum producing status of an oil well generally may be obtained by the conditions that subject the producing formations to the least possible back-pressure. This pressure is made up of the weight of the fluid column, frictional resistance to flow and the reaction from the acceleration of the fluid mass. A mathematical calculation of these components to arrive at a condition giving a minimum summation is impractical. Formulas would be complex and the results untrustworthy because it is impossible to assign proper values to the many variables involved.

Jan 1, 1931

Some years ago the open Hearth Committee of the Institute reached the conclusion that the reading of "set" papers tended to preclude the specific and detailed discussion of specialized problems of current interest to those operating steel plants. As an innovation the Committee distributed in advance of the meeting in May, 1927, a questionnaire containing a list of 27 topics involving operating problems. The subsequent discussion of the questions, participated in by 37 members, was a conspicuous success. Semiannual meetings have been held since; and at the conference of November, 1929, at Chicago, 131 men were present and the minutes comprised a book of 133 printed pages, thereby, indicating the growing value of the conference in the eyes of both the metallurgists themselves and the companies that employed them. With this example in mind, the Directors felt that definite advantages would accrue to a similar conference to be participated in by smelter officials and metallurgists engaged in the operation of copper reverberatory furnaces. The settlement of the Carson litigation, which for several years had virtually stopped public discussion of reverberatory practice, offered an opportune time for launching the scheme. Although the Conference may become largely self-financing in the future, some funds were regarded as necessary to conduct the first meeting. The members of the Rocky Mountain Income Committee, in view of the fact that copper smelting was essentially an activity of the Rocky Mountain area, recommended the project be, in effect, underwritten by the Fund, and the directors approved an appropriation for this purpose. Invitations were extended to high executives of the various-companies interested to send representatives to an initial meeting to be held at Salt Lake City, May 26-27. The response was enthusiastic. Twenty-three metallurgists representing 12 different plants were present to discuss the comprehensive-program relating to construction and operating phases of reverberatory smelting. It was understood that the record was not to be included in the regular publications of the Institute but that it would be prepared for private distribution among the participants and the officials of their companies. That the exchange of views and experience was no less instructive and stimulating than it was frank, full and informal is indicated by the following transcript of the minutes of the meeting.

Jan 1, 1930

By Taylor Lyman, E. P. Klier

The structures formed when austenite is quenched to subcritical temperatures and allowed to transform isothermally have been the subject of intensive study since the work of Davcnport and Bain.' Isothermal transformation diagrams summarizing the results of many of these studies have become widely familiar to metallurgists. Of particular interest to metallographers are the dark-etchingl acicular products of transformation formed by isothermal reaction below the temperature of maximum velocity of the austenite to pearlite reaction. These products, the bainite structures, can he formed in a wide variety of steels. However, the constitution of bainite is not well understood and divergent views have been expressed as to its mode of formation. In this investigation a combination of dilatometric, microscopic and X-ray methods has been brought to bear upon the problem in the hope of some elucidation of the bainite reaction as it occurs in hypo-eutectoid steels. Mechanism OF Bainite Formation Davenport and Bainl considered the mechanism of bainite formation to consist of two steps—an allotropic transformation followed by precipitation of carbide. The separation in time of the two processes was considered to be very slight in the upper temperature range and very marked at temperatures just above the martensite range. This concept has been restated by Vilella, Guellich and Bain2 in the form of a definition of the acicular mode of transformation as: The successive, abrupt formation of flat plates of supersaturated ferrite along certain crystallographic planes of the austenite grains; this supersaturated ferrite begins at once to reject carbide palticles, (not lamellae), at a rate depending upon temperature In effect, this is the acicular mode of transformation, even though the temperature be such as to limit the actual life of the quasi-martensite to millionths of a second. The investigation of isothermal decomposition of austenite in certain alloy steels (notably those containing chromium or molybdenum) has revealed that there may be a range of temperatures between the pearlite and bainite reactions in which the austenite decomposes at a relatively low rate.3-6 Further, it is characteristic that in the second region of fast reaction the decomposition of the austenite is incomplete by one reaction but goes to completion by a second reaction. These observations led Wever7 to a description of the bainite reaction as follows: I. The reaction takes place by initial precipi. tation of a martensitic intermediate structure. 2. In the upper temperature range this structure readily decomposes into ferrite and cementite. In the lower range carbon separates in an unknown form. 3. In the upper temperature range the precipitated carbide nucleates the precipitation

Jan 1, 1944

By E. P. Klier, Taylor Lyman

The structures formed when austenite is quenched to subcritical temperatures and allowed to transform isothermally have been the subject of intensive study since the work of Davcnport and Bain.' Isothermal transformation diagrams summarizing the results of many of these studies have become widely familiar to metallurgists. Of particular interest to metallographers are the dark-etchingl acicular products of transformation formed by isothermal reaction below the temperature of maximum velocity of the austenite to pearlite reaction. These products, the bainite structures, can he formed in a wide variety of steels. However, the constitution of bainite is not well understood and divergent views have been expressed as to its mode of formation. In this investigation a combination of dilatometric, microscopic and X-ray methods has been brought to bear upon the problem in the hope of some elucidation of the bainite reaction as it occurs in hypo-eutectoid steels. Mechanism OF Bainite Formation Davenport and Bainl considered the mechanism of bainite formation to consist of two steps—an allotropic transformation followed by precipitation of carbide. The separation in time of the two processes was considered to be very slight in the upper temperature range and very marked at temperatures just above the martensite range. This concept has been restated by Vilella, Guellich and Bain2 in the form of a definition of the acicular mode of transformation as: The successive, abrupt formation of flat plates of supersaturated ferrite along certain crystallographic planes of the austenite grains; this supersaturated ferrite begins at once to reject carbide palticles, (not lamellae), at a rate depending upon temperature In effect, this is the acicular mode of transformation, even though the temperature be such as to limit the actual life of the quasi-martensite to millionths of a second. The investigation of isothermal decomposition of austenite in certain alloy steels (notably those containing chromium or molybdenum) has revealed that there may be a range of temperatures between the pearlite and bainite reactions in which the austenite decomposes at a relatively low rate.3-6 Further, it is characteristic that in the second region of fast reaction the decomposition of the austenite is incomplete by one reaction but goes to completion by a second reaction. These observations led Wever7 to a description of the bainite reaction as follows: I. The reaction takes place by initial precipi. tation of a martensitic intermediate structure. 2. In the upper temperature range this structure readily decomposes into ferrite and cementite. In the lower range carbon separates in an unknown form. 3. In the upper temperature range the precipitated carbide nucleates the precipitation

Jan 1, 1944

By R. S. Archibald

The subject of this paper is particularly appropriate, since Daniel C. Jackling was active in early exploitation of taconites on the Mesabi Range and contributed greatly to their later economic development. After his success in developing the low grade porphyries in the West he looked for more worlds to conquer, and so undertook the concentration of low grade taconites, from which he hoped to produce commercial ore. Mesabi Iron Co., organized in 1919, actually did produce merchantable sinter from taconites in 1922. The enterprise did not prove commercial at the time, as cost of production was high and the surplus of iron ore in the Lake Superior District already contributed to a low market price, but this same property has since been developed by Reserve Mining Co. The work done by Jackling had much to do with the success of this later venture. Iron ore was first discovered on the Marquette Range in Michigan in 1845. The first ore from this range came from the old Jackson mine in Negaunee in 1848. During these early years this property and others on the Marquette produced limited tonnages for transportation to Lower Lakes and for consumption by charcoal furnaces in the area, where a plentiful supply of hardwoods furnished the charcoal for iron smelting. The Marquette and other ranges tributary to Lake Superior did not produce much ore for transportation to Lower Lakes until the locks at Sault Ste. Marie were constructed, but from the time the first lock at the "Soo" was completed in 1855 these ores were transported through the locks to consumer centers in the East. The Marquette Range has a history of continuous production from 1848 to the present day. In 1877 the Menominee Range was discovered at the location of the old Penn Mines near Vulcan, Mich. There were further discoveries of ore on the old Menominee Range and at Florence, Wis., in 1880 and at Iron River and Crystal Falls, Mich., in 1882. Penn Mines continued in operation from the date of their discovery until they were finally exhausted by Pickands-Mather in 1945, but operations still continue on the Menominee in the Crystal Falls and Iron River districts. Ore is shipped to a lake port at Escanaba, Mich.

Jan 1, 1960

By E. H. Crabtree, Neil S. Parker

The custom milling plant of the Eagle-Picher Mining and Smelting Co. is at Sahuarita, Arizona, approximately 20 miles south of Tucson. It is connected by a 2-mile railroad spur to the main line of the Southern Pacific Railroad between Tucson and Nogales. The capacity of the plant is 500 tons per day. The mill is conventional except perhaps in the rather wide variety of ores treated. These vary from straight copper ores, from which only one concentrate is produced, and lead-zinc or copper-zinc ores from which two concentrates are produced, to complex gold-silver-copper-lead-zinc ores, which require the simultaneous production of three or lour concentrates. Custom ores are received in lots varying in size from a few truckloads to several carloads. Similar ores, after crushing and sampling, may be commingled, or individual lots may be milled individually. The ores are first dumped either into one of two 200-ton railroad bins, or into one of the two 75-ton truck bins. From these bins the lot of ore is individually crushed in a 24 by 16-in. jaw crusher to 3-in. size, and then to ½-in. size in a 3-ft Symons shorthead crusher. After crushing to ½-in., the ore is conveyed to the automatic sampling plant. This consists of three Vezin samplers in series, each successively cutting out 10 pct, 10 pct and 5 pct of its feed. After No. I sampler, the material passes through a mixing barrel and is then crushed to -in. in a set of rolls before passing to No. 2 sampler. Between No. 2 and No. 3 samplers, the ore is again mixed in a mixing barrel. The final sample, consisting of one pound per ton of ore, is taken to the laboratory, where it is further crushed to 1/8-in. in a coffeemill, and then riffled down to the size required for grinding in a pulverizer. The capacity of the crushing and sampling plant is up to 100 tons per hour, depending upon the character of the ore. After sampling, the ore is stored in five ore-storage bins, consisting of four 200-ton bins and one 175-ton bin. Each of these bins is discharged by means of belt feeders and conveyor to the ball mills, so that ores may be composited for milling in any required ratio, or milled separately by themselves. Fine grinding is done in one 6 by 4-ft Allis-Chalmers ball mill and one 8-ft by 36-in. Hardinge mill. These two mills both discharge to one 54-in. Akins Simplex High weir classifier. The classifier sands can be returned to either or both mills, so that flexibility in grinding for different ores is easily obtained. Flotation equipment consists of four 66-in. Fagergren machines for copper-lead roughing and six similar machines for zinc roughing. Lead-copper bulk concentrate is cleaned and recleaned in eight No. 18-S Denver machines, and zinc concentrate is cleaned in three 66-in. Fager-grens. Copper-lead differential separation

Jan 1, 1949

By W. H. McFarland

The mechanical properties have been determined for a large number of alloy-free martensitic steels with carbon contents ranging from 0.08 to 0.20 pct and with manganese contents of about 0.4 to 0.5 pet. These steels were tested 1) as water-quenched, 2) after quenching, temper rolling, and tinning, and 3) after tempering treatments which involved temperatures from 400o to 1300oF and times from 1 min to 8 hr. The majority of these tests represent steel from commercial-size coils, i.e., strip 32 in. wide, coil weights up to 20,000 16, and steel thicknesses from 0.0055 to 0.024 in. As a result of these treatments, it has been shown that as-quenched low-carbon alloy-free steels can be produced with tensile strengths ranging from 140,000 to 220,000 psi and tensile elongations from 3.0 to 4.0 pet in 2 in. The tensile strength of the as-quenched martensites can be represented by the equation, tensile strength (ksi) = 119 + 560 (wt pet C). The response to tempering of these steels is related to previous work by Muir, Averbach, and Cohen and by Grange and Baughman. Strain aging of low-carbon martensite has also been investigated. If low-carbon steels are defined as those steels with a maximum carbon content of 0.2 pet, it is found that the literature on low-carbon, alloy-free martensites contains little data on the mechanical properties of these steels. However, the following facts concerning low-carbon alloy-free martensites seem firmly established:'-' 1) The major factors in controlling the strength of the martensite appear to be a) fine structure, b) the internal strain resulting from the transformation, and, particularly, c) the amount of carbon in solid solution. 2) In low-carbon steels, the martensite is auto-tempered and is in the form of needles with only minor amounts of internal twinning, whereas the martensite in high-carbon steels forms as plates which are internally twinned on a fine scale. 3) Care must be taken in comparing the results of work that has been done on low-carbon steels with varying amounts of alloying elements to data on plain carbon steels. As has been noted by Irvine, Pickering, and Garstone,6 alloying elements generally lower the martensite start temperature and, thereby, decrease the amount of auto tempering obtained during the quench. This makes it difficult to

Jan 1, 1965

By Robert M. Betts

The Cornucopia district is situated in northeastern Oregon 25 miles from the Snake River branch of the Oregon Short Line R.R. and 75 miles northeast of Baker City, in the Wallowa Mountains. The formation is principally granodiorite, which has intruded much older rocks locally known as greenstone, and which are probably altered schists. In the upper horizons of the veins, greenstone is found as inclusions in the granitic mass. Both of these formations have been cut by numerous basalt, aplite, and porphyry dikes. Veins of the district are the result of faulting and the consequent crushing of the wall rock. The ore has been deposited irregularly along these faults and formed a lenticular type of vein. The ore varies in width from a few inches to 20 ft.; the average stoping width is about 5 ft. As the basaltic dikes are subsequent to the ore deposition, they are at times a hindrance in development and mining operations; on the other hand, a dike which has followed a vein as a line of least resistance often serves as a good mall in place of the crushed, rather loose granite. The veins generally strike northeast-southwest and dip about 35" to the west. Orebodies are from 100 to 300 ft. in length and about the same in height. The lenses are irregular; inclusions of wall rock are common in the ore and are a factor in reducing the grade. The ores are quartz, carrying some free gold near the surface, but the metals for the most part are in iron sulfides, sometimes associated with chalcopyrite. The gold and silver are in a mechanical combination with the iron, which requires find grinding to liberate them. The ratio of silver to gold is 5 to 1, by weight. Development The Cornucopia Mines Co. owns, and operated until 1920, two mines and two mills of 100 tons capacity each. The sustained high costs and labor shortage, however, necessitated the abandoning of the Union mine, the oldest in the district. Two crosscut tunnels were then started, first, to cut the Last Chance vein at a much lower horizon and, second, to prospect two parallel veins. The ore from the Last Chance vein will go to the old Union mill and the ore from the new veins to the Last Chance mill.

Jan 1, 1925