Search Documents

By M. L. Requa

This paper is abstracted from the report of the Appraisement Committee of the Independent Oil Producers' Agency, of which the writer was Chairman. The other members of the committee were M. V. McQuigg and R. S. Haseltine. To Thomas Cox, engineer in charge of the investigation, and to his efficient staff of assistants, is due the credit for the detail work necessary in carrying out the plan of the Committee. It treats only of the valuation of the lands, wells, and piping, without going into details of equipment and other features. It was recognized, early in the operation, that the value of oil lands was the value of oil ,to be extracted and marketed, less the costs attendant thereon. Referring this back to the costs in cents per barrel, it became obvious that surface improvements, absolutely necessary in the production of oil, from wells then drilled, had no separate and independent value aside from the value of the land, but that any excess equipment, not necessary for the production of oil from present wells, such as drilling tools, well casing, etc., should be given a present condition value. In valuing the properties of the Independent Oil Producers' Agency, the Committee has considered the following facts: 1. That from each property there will ultimately be produced a certain total quantity of oil. 2. That in the production of that oil a certain total quantity of money will be expended. 3. That a certain total amount of money will be received from the oil. 4. That the total net receipts will be the total gross receipts less the cost of development and production. 5. That the present value of the net receipts must be such an amount that when invested by a purchaser it will be returned with 8 per cent, interest additional during the life of the property. The initial procedure consisted in making a general reconnaissance of the entire district in which the property was located and determining the lithological and structural conditions underlying the area. The data obtained from each individual tract comprised the logs of all the wells

Jan 1, 1918

By M. W. Bartley, Hugh M. Roberts

Substantial deposits of Bessemer hematite have been found recently by drilling beneath Steep Rock Lake, Ontario, which is situated in the northern part of the Lake Superior Region. It will be practicable to divert the waters flowing into this lake and develop open pits on the upper pert of two large ore bodies by damming off and pumping out the water in the part of the lake in which they occur. Ultimately, the bulk of the ore will be mined by underground methods. Owing to the generally massive nature of the rocks in the area, no underground flows of major consequence are anticipated after diversion of the lake. The Steep Rock deposits are attributed in origin to hydrothermal replacement. They were formed, for the most part, along an unconform-able, brecciated contact between the Steep Rock limestone and an overlying younger volcanic series, The replacing solutions came in as igneous after-effects, following upon the intrusion of basic igneous rocks that invaded the hanging-wall volcanics. It is believed that this took place in a geological period roughly equivalent to late Middle Huronian, which was the period when the most extensive iron-bearing rocks of the Lake Superior Region were formed. Comparison is made with other deep-seated iron-ore bodies in the Lake Superior Region, the origins of which are ascribed in the discussion to hydrothermal replacement. Introduction Under the waters of Steep Rock Lake, Ontario, situated on the Canadian National Railway, 142 miles west of Port Arthur, the presence of three ore zones containing red and brown Bessemer hematite has been established. These were discovered and have been partly explored by means of diamond and churn drilling, The positions of the ore zones, designated as A, B and C, are shown on the accompanying maps and cross sections. This exploratory work, begun in 1938 by Joseph Errington* and Julian G. Cross, has been carried on by Steep Rock Iron Mines Ltd., and was continued during the winter of 1941-1942. For more than 60 years explorers have known that large quantities of hard hema. tite float of good grade existed along the south shore of Steep Rock Lake, and the presence of ore beneath the lake was inferred by many early geologists and explorers. Despite numerous previous attempts to find ore in place, actual discovery awaited the recent period of intensive exploratory effort in Canada. The results obtained in the drill holes put down since 1938 by steep Rock Iron Mines Ltd. are not only of interest, in themselves, to those concerned with the development of ore deposits, but, taken in connection with the surface exposures of adjoining formations, they form the assemblage of facts from which the geological reasoning in this paper proceeds; accordingly, they are set out here as briefly and exactly as may be.

Jan 1, 1949

By M. W. Bartley, Hugh M. Roberts

Substantial deposits of Bessemer hematite have been found recently by drilling beneath Steep Rock Lake, Ontario, which is situated in the northern part of the Lake Superior Region. It will be practicable to divert the waters flowing into this lake and develop open pits on the upper pert of two large ore bodies by damming off and pumping out the water in the part of the lake in which they occur. Ultimately, the bulk of the ore will be mined by underground methods. Owing to the generally massive nature of the rocks in the area, no underground flows of major consequence are anticipated after diversion of the lake. The Steep Rock deposits are attributed in origin to hydrothermal replacement. They were formed, for the most part, along an unconform-able, brecciated contact between the Steep Rock limestone and an overlying younger volcanic series, The replacing solutions came in as igneous after-effects, following upon the intrusion of basic igneous rocks that invaded the hanging-wall volcanics. It is believed that this took place in a geological period roughly equivalent to late Middle Huronian, which was the period when the most extensive iron-bearing rocks of the Lake Superior Region were formed. Comparison is made with other deep-seated iron-ore bodies in the Lake Superior Region, the origins of which are ascribed in the discussion to hydrothermal replacement. Introduction Under the waters of Steep Rock Lake, Ontario, situated on the Canadian National Railway, 142 miles west of Port Arthur, the presence of three ore zones containing red and brown Bessemer hematite has been established. These were discovered and have been partly explored by means of diamond and churn drilling, The positions of the ore zones, designated as A, B and C, are shown on the accompanying maps and cross sections. This exploratory work, begun in 1938 by Joseph Errington* and Julian G. Cross, has been carried on by Steep Rock Iron Mines Ltd., and was continued during the winter of 1941-1942. For more than 60 years explorers have known that large quantities of hard hema. tite float of good grade existed along the south shore of Steep Rock Lake, and the presence of ore beneath the lake was inferred by many early geologists and explorers. Despite numerous previous attempts to find ore in place, actual discovery awaited the recent period of intensive exploratory effort in Canada. The results obtained in the drill holes put down since 1938 by steep Rock Iron Mines Ltd. are not only of interest, in themselves, to those concerned with the development of ore deposits, but, taken in connection with the surface exposures of adjoining formations, they form the assemblage of facts from which the geological reasoning in this paper proceeds; accordingly, they are set out here as briefly and exactly as may be.

Jan 1, 1949

By J. S. Kasper, R. M. Waterstrat, B. F. Decker

THE existence of v phase in the Mn-Mo system was discovered in this laboratory several years ago,' but neither the conditions of its formation nor its composition were known, and preliminary attempts to reproduce the phase were unsuccessful. We wish now to specify the information appropriate to phase formation on the basis of experiments performed since that time. The starting materials were in every case electrolytic manganese and high purity molybdenum. Two methods of preparation were employed: l—arc-melting varying combinations of the elements in an inert atmosphere and subsequent heat treating, and 2—sintering compressed mixtures of finely divided powders of the elements. In the latter method, the powders were first passed through 200 mesh screen and then compressed into cylinders of % in. diameter and % in. length, which were sintered at elevated temperatures in an atmosphere of dry hydrogen. For some samples, the sintering temperature was 1200°C (for 1 hr), and these were then heat- treated at lower temperatures for times up to 24 hr. Eventually it was found, for the proper composition, that essentially pure a phase could be produced by sintering at 1125°C for 3 hr. Quenching to room temperature was effected by means of a stream of cold, dry hydrogen in a water-cooled chamber. The arc-melting procedure was found to be unsatisfactory after an investigation of many samples at different compositions and temperatures. Large quantities of manganese were vaporized during melting and none of the products were homogeneous or contained extended regions of pure phase. Nonetheless, these experiments established that no formation occurs in the Mn-Mo system below 1115oC, and indicated, at least roughly, the composition range of interest for further exploration. The more definite results obtained from samples produced by the second method are given in Table I. A portion of sample 2 heated for 16 hr at 1000°C in a Vycor tube transformed to molybdenum plus unidentified phases of complex X-ray pattern. From these few results it appears that the region of phase is quite narrow in composition. It is of interest that the composition is such as to make for difficulties in correlating this structure on an electron atom basis with other a structures of iron, cobalt, and nickel. In that respect Mn-Mo shows the same anomaly as Mn-Cr and Mn-V systems.' A second feature is that in common with the two other known molybdenum (Fe-Mo and Co-Mo), Mn-Mo v exists only at elevated temperatures. The X-ray powder pattern of the pure a phase of Mn-Mo is given in Table 11. It agrees well with the patterns established for other structures, especially with that for Fe-Mo as given by Goldschmidt.An attempt is being made to establish whether an ordering of the respective atoms occurs and such information will be reported in a future publication. Acknowledgment The authors acknowledge gratefully the assistance of Mrs. J. R. Belanger in some portions of this work. References 'J. S. Kasper, B. F. Decker, and J. R. Belanger: Journal of Applied Physics (1951) 22, p. 361. 2 A. H. Sully: Journal Inst. Metals (1951) 80, p. 173. H. J. Goldschmidt: Research (1949) 2, p. 343.

Jan 1, 1954

By H. B. Pulsifier

THE following report on the structure of copper is the result of work done in the laboratory of the Rome Wire Co. early in 1925. Previous work had indicated to the author that excellent results might be expected if a suitable technique in surfacing and etching could be developed. The resources of the Rome Wire Co. enabled this metal to be studied more intensively than previously, although none of the materials were investigated exhaustively. The material presented is hardly more than a preliminary summary of the most obvious character of the metal; a much longer research would have been necessary to solve many of the pressing problems connected with the casting and working of copper. The Rome Wire Co. has generously released the paper; to Dr. E. H. Darby, technical supervisor of the company, are due particular thanks for his appreciation of the importance of metallographic study of copper and for his effective support in the prosecution of the work and in making its publication possible.

Jan 1, 1926

By Jr. Ensign C. O., J. W. Trammell

The two principal methods of room-and-pillar mining practiced at White Pine make it important to predict variations in the thickness and rock types of a stratum called the upper sandstone. In full column mining, the nearly barren upper sandstone occurs between two ore horizons (called upper shale and parting shale, respectively), and is mined as a part of the ore column. In general, full column mining is not practiced where excessive upper sandstone thickness causes full column ore grade to be substantially lower than parting shale ore. In parting shale mining, the upper sandstone forms the mine roof. Difficulty in predicting upper sandstone character arose because the extent and directions of its variations were not apparent in the property's diamond drilling, in which holes are spaced on 1000-ft centers. A study of sedimentary features, undertaken to improve the predictability of trends in the upper sandstone, led to an interpretation of the sedimentary environment in which the sandstone was deposited. Ripple marks, mud cracks, and cross-bedding, as well as other, less well known features, such as channel casts, flute casts, and current crescent casts, were mapped or recorded. These data, coupled with the knowledge of regional facies changes gained from studying drill core, show that the upper sandstone was deposited by a series of streams flowing northeastward over the underlying parting shale. Deposition of the lowermost bed of the upper sandstone, near the ancient shoreline, was locally preceded by erosion of the parting shale, and the greatest thicknesses of sandstone are found in channels scoured out of the parting shale. Awareness of the rather strong linear trends in the upper sandstone makes it possible to project continuous areas of thick upper sandstone through apparently isolated "highs" in the upper sandstone thickness contour map, which is based on drill-hole information. Since local exceptions to general stratigraphic trends exist, a method was also needed for esti- mating, in detail, the thickness and degree of shali-ness of upper sandstone forming the roof in active parting shale mining areas. Because locally the parting shale was thinned by erosion during the deposition of upper sandstone, parting shale thickness is inversely proportional to upper sandstone thickness. Utilizing information taken from short drill holes into the roof, curves were constructed for the correlation of parting shale thickness (measurable in the mine) with the upper sandstone total thickness, as well as the thickness of its basal member. The White Pine mine is situated in Ontonagon County, approximately 6 miles south of Lake Superior, in the Upper Peninsula of Michigan (Fig. 1). The orebody mined by White Pine Copper Co. occurs in the lowermost 20 to 25 ft of the Nonesuch formation, a series of middle- to upper-Keweenawan shales, siltstones, and sandstones. This paper discusses the solution of problems in ore grade control and mine planning arising from the presence of an essentially barren sandstone stratum within the orebody. THE OREBODY AND MINING TYPES A brief description of the orebody and mining methods is necessary to show how the upper sandstone affects mine planning and grade control. In the mine, the cupriferous zone of the Nonesuch shale is divided into three major portions, as shown in Fig. 2. Lying conformably on top of the Copper Harbor formation (or "lower sandstone") is the lower part of the orebody, the parting shale. The parting shale is overlain by the upper sandstone. On top of the upper sandstone, the basal portion (8 ft) of the upper shale is quite similar to the parting shale. Both the upper shale and parting shale are divided into a number of smaller stratigraphic units, each having a characteristic copper content, as shown by the histogram of Fig. 2. Other authors1'3 have dealt in detail with the stratigraphy and mineralogy of the orebody. However, in this article, we are concerned with the major subdivisions only, and it will suffice to note the low copper content of the upper sandstone, shown in Fig. 2. At present, two types of room-and-pillar openings are created in the orebody. In one type, called parting

Jan 1, 1964

By John Greenawalt

IN view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by com-bustion within the mass itself. Its first successful application, in connec-tion with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremen-dous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blown off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for ignit-ing purposes.

Jan 1, 1938

By Charles Catlett

(San Francisco Meeting, October, 1911.) WHILE the occurrence of phosphorus in coking-coal has assumed less importance with the development of the open-hearth method of steel-making, it may not be without interest to note the form in which phosphorus exists in one particular coal-seam. In the examination of what is known as the Big seam, which outcrops a few miles west of Columbiana, Ala., my attention was called to the distribution through the coal, in the form of minute veins and particles, of a resinous-looking substance. A small amount of this was selected, and was provisionally identified as evansite (Al6, P2 014. 18 Aq). Subsequently, through the courtesy of Dr. Sharshall Grasty of the Geological Department of the University of Virginia, I was able to secure an additional amount of material, which was purified down to about 0.3 g. This was examined by Prof. John J. Porter of the University of Cincinnati, and gave the following partial analysis

Nov 1, 1911

By M. J. Marcinkowski, K. S. Sree Harsha

A detailed numerical analysis has been made of the equilibrium configuration of partial dislocations in a blocked deformation twin under an externally applied stress. Twins made up of both pure screw and pure edge partials have been considered. The components of stress in the vicinity of the twin tip associated with each of these configurations have been plotted. It has been found that at some critical degree of oblateness the shear stress fields of the blocked screw or edge twin can both sPontaneously nucleate slip, whereas only the component of stress oxx about the edge twin can nucleate and propagate cracks. TWINNING becomes a predominant mode of plastic deformation at low temperatures and/or high strain rates. Fig. l(a) shows what must be the first step in the formation of a deformation twin, namely the formation of a loop of imperfect dislocation bounding a stacking fault. In an fcc crystal the partial dislocations have Burgers vectors of the type 1/6 a,(112) and the fault is of the intrinsic type while in the bcc crystal the partials have Burgers vectors of the type ao(lll). The stacking sequence of (111) planes in a perfect fcc crystal is given by ABC ABC, and so forth, and in one which contains a twin by ABCABACBA, and so forth. It is apparent that the stacking fault and twin give rise to no mistakes associated with adjacent close-packed planes; however, with respect to second-neighbor close-packed planes the faulted crystal has twice as many mistakes as the twin. The energy of the twin boundary may thus be taken to be one-half that of the intrinsic fault boundary. In the case of the bcc crystal the stacking sequence of (112) planes is given by ABCDEFABCD, and so forth, in a perfect crystal, by ABCDCDEFA, and so forth, in a crystal which contains a fault, and by ABCDCBAF, and so forth, in one which contains a twin. An analysis similar to that applied in the fcc crystal shows that both the fault as well as the twin involve no neighbor violations across adjacent planes. However, there are twice as many violations across second-neighbor (112) planes associated with the fault as compared to that of the twin. Thus once again the energy of the twin boundary may be taken as one-half that of the fault. It is important to note that, unlike the fcc, the faults in the bcc crystal involve first nearest-neighbor violations and are thus expected to be of much higher energy than those in fcc crystals. A more detailed analysis of the material discussed above can be found in Ref. 1. To a good approximation then, the lenticular twin shown in Fig. l(b) can be generated by adding partial dislocation loops on successive (111) planes for fcc crystals or (112) planes for bcc crystals in the manner shown, with no additional expenditure of chemical energy other than that required for the fault shown in Fig. l(a). In practice, deformation twins are much more extended than that shown in Fig. l(b) and more closely resemble one shown schematically in Fig. l(c). It is readily apparent that the free energy of the twin and matrix are identical. In those cases where the partials lead to a structural change, the free energy of the material contained within the dislocation array is lower than that of the matrix and we have the so-called martensite transformation. The present investigation is the first in a series of five major theoretical-experimental efforts which will deal with the static and dynamic behavior of twin nucleation and growth. There has been a recent surge in activity pertaining to the equilibrium shapes of twin lamellae2'3 and

Jan 1, 1969

By P. P. Scott, George C. Howard

A field remedial procedure utilizing a kerosene-cement slurry as a water plug-off agent in fractured formations was evaluated both in the laboratory and in the field. This procedure has proved to be capable of effectively shutting off water without causing permanent impairment of the oil production. Success was attributed to the fact that an immobile cement slurry, when placed in a water-producing strata, will set and form an impermeable barrier; whereas when placed in an oil-producing section the cement will retain a relatively high permeability and may be removed by acidizing. INTRODUCTION One of the most perplexing problems facing the oil industry is the selective exclusion of water production from oil or gas-producing wells. This problem has been studied by many investigators in an attempt to develop a material that is not only capable of reducing water production but is also capable of being selective in that it will not impair oil production in either fractured or intergranular type reservoirs. A study of these two types of formations indicated that two distinct types of materials for controlling water production might be required — a completely liquid plugging agent for intergranular formations and a semi-liquid or slurry type plugging agent for fractured formations. This paper is limited to the control of water production from fractured formations. A common source of water in the vicinity of oil bearing rock reservoirs is water which previously has entered and, because of its higher density, generally lies near the bottom of the formation. When the deepest point of penetration of a well into such an oil and water-bearing formation is above the level of the water, and the dynamical gradients due to the flow of oil overbalance the difference in densities between oil and water, water production becomes a problem. Then the water level rises in the shape of a cone and is produced from the lower depths. Other investigators1,2,3,4 have developed theories which define the pressure gradients and contours of this cone in a homogeneous formation and have shown that the placement of a plug in the bottom of a well is only slightly effective in temporarily reducing the flow of water. Assuming that the manner of flow of bottom water from fractured formations to a well is generally similar to the flow in homogeneous formations, then it would be expected that some form of coning, perhaps of less symmetry, would also occur. Then, because of the similarity of the manner of flow of water, placement of a vertical plug in a fractured formation would also probably be ineffectual for controlling water production. However, as has been shown by electric model flow study,' the placing of a plug in a well and an impermeable horizontal streak in the formation might prove to be a means for materially reducing or even eliminating water production in a fractured formation. An indication of the difference in effectiveness between horizontal and vertical plugs based on theory developed from study of the flow of water and oil in rock reservoirs is depicted in Fig. 1. These curves show the expected

Jan 1, 1955

By Walter H. Munk

Generation of Waves by storms, and the transformation of waves in shallow water by local bottom topography are briefly reviewed. A detailed description of water motion in waves explains the nature and distribution of wave forces. A numerical example dealing with forces and moments against vertical piles summarizes the principles involved. Introduction The oil industry is moving into the open waters of the Gulf of Mexico. The design and construction of offshore drilling rigs present a number of difficult problems, among them problems involving the action of waves on fixed and floating structures. This paper deals with our present knowledge of ocean waves as it pertains to these problems, and the principles involved in computing wave forces against fixed structures. It is hoped that the more difficult case pertaining to floating structures can be discussed at a later time. None of the engincering aspects of the problem are entered upon in this paper, yet an understanding of the principles presented here should be helpful in the solution of practical problems. Waves are capable of exerting almost unbelievable forces. During a gale, waves at the harbor entrance of Amsterdam Canal in Holland lifted a 20-ton concrete block, which was resting on the bottom in 12ft of water, and deposited it on top of a pier which was 5 ft above the high water mark. At Wick Breakwater in Scotland, a mass of large stones in cement and bound together with iron rods, weighing 1350 tons, was broken loose and moved bodily! But one need not go to Holland or Scotland to find evidence of damage that waves are capable of inflicting (Fig I and 2). What is the mechanism by which waves are capable of exerting such enormous forces? To answer this, we must consider briefly the nature of wave motion. When a wind blows over a wheat field, waves appear to travel across the field, whereas the wheat itself remains rooted, slowly swinging back and forth. Similarly, in the case of water waves, the waveform travels swiftly over the water surface, whereas the water particles oscillate back and forth, but scarcely advance. The speed of the wave form is called wave velocity, the speed of the water particles is called orbital velocity. This fundamental difference between wave velocity and orbital velocity was already recognized by Leonardo da Vinci. Orbital velocity is generally much slower than wave velocity except for a breaking wave, a case which is of particular importance in the application to engineering problems. Forces exerted by the waves on obstacles

Jan 1, 1949

To the American Institute of Mining Engineers: The committee appointed at the February meeting upon Railway Resistances would respectfully report: That one person has been constantly employed in calculating the results of the data taken prior to March 1st, 1876. Also to complete the data taken upon the Lake Shore and Michigan Southern Railway, a diagram was taken upon a through freight train from Cleveland to Chicago, and one from Chicago to Cleveland. So that now we have diagrams from Buffalo to Chicago and return, which, when fully worked up, will give results of the utmost importance in determining the cost of transportation of freight. These data will be of much importance in determining the proper methods of equating grades and curves, which is so essential in the location of new lines. The calculations show that instead of our attempting to formulate results from data obtained on one road, it will be best for the in¬terests of transportation to enlarge the scope of our inquiries, and to extend the experiments so as to include all of the more probable causes which affect the cost of transportation. Were the details of railway equipment constructed alike, much work, which is now necessary, would be saved. It is not uncommon to find upon the same road 10 to 30 different patterns of something in construction to subserve the same purpose, which more or less modifies the friction of the cars. Take the majority of our trunk lines, with this diversity of construction, together with the varying conditions of track and manner of operating, and it will be at once seen that the labor and time to do the work and arrive at correct conclusions will occupy from two to three years. The results already attained in the short time in which they have been carried on, wholly by private enterprise, simply show what may be expected when the aid necessary is given to render them of the highest value to the great industries of the country. That the information may be general and of the greatest importance to our railway interests, the committee deem it advisable to secure, so * The following report, made at the June meeting of the Institute, is inserted in this place as appropriately supplementing the original communication of Mr. Dudley.

Jan 1, 1876

By Warren B. Davis

Introduction If a subject this broad were to be covered in even moderate detail, it would require a set of books about the size of an encyclopedia. Since an acceptable length for this paper is a small fraction of one book, it will have to consist of a few samples of the subjects that I think are the most pertinent to World Fossil Fuel Economics. I plan to discuss the trends in world energy demand, particularly in the U. S. and Europe; the consumption patterns and cost patterns of oil, gas and coal; the prospects of synthetics; and some of the effects of government regulation of fuel economics. World Energy Demands Fig. 1 shows Free World energy consumption by principal areas for the period from 1950 to 1970 and a forecast for the period from 1970 to 1985. These figures include only the measurable forms of energy. An example of energy consumption that is not measured is the wood a peasant might cut in the forest and bum in a fireplace to heat his home. This omission probably is a very small part of the total. This forecast is not identical with that of Wayne E. Glenn (see Page 22), but the differences in total energy consumption are not significant. The U. S. consumption, which was 55 percent of the world total in 1950, had declined to 45 percent by 1970, and is expected to decline further to 38 percent by 1985. Western Europe has consumed 28 percent of the total from 1950 to 1970 and is expected to lose share slightly between 1970 and 1985. The most spectacular gainer is Japan, which increased consumption from 2.5 percent in 1950 to 7.5 percent in 1970, and is expected to reach nearly 17 percent by 1985. The over-all Free World total has grown from 62 quadrillion Btu (equivalent to 29 million B/D of crude oil) in 1950 to 151 quadrillion by 1970, an average growth rate of 4.5 percent/year. This total is expected to grow at a rate of 5 percent/year between now and 1985, reaching 315 quadrillion Btu (equivalent to nearly 150 million B/D). Fig. 2 shows which fuels supplied this energy between 1950 and 1970, and gives an estimate of how it will be supplied between 1970 and 1985.

Jan 1, 1971

By T. J. Koppenaal, M. E. Fine

A yield point effect attributed to short-range ordevi?g (SRO) occurs in Cu base Al. At at 296°K varies with heat treatment, decreasing as the annealing ternperature is raised .from 433Oto 598°K. Davies aid Cahn' observed a corresponding decrease in SRO. (523 °K anneal, measured at 77°K) is approximateZy proportional to the variations of A7 with strain rate and testing temperature are also Consistent with the idea that is associated with SRO. A preliminary investigation of the tensile properties of a Cu-Al single crystals showed the presence of a rather strong yield-point effect (drop in flow stress after initial yielding). The object of this research was to investigate its origin and behavior. a Cu-Al alloys are particularly interesting because diffuse X-ray scattering measurements by Davies and Cahn,' Houska and Averbach,' and Borie established the presence of short-range order. The degree of local order may be changed with heat treatment.' cottrel14 suggested that the presence of local order might result in a yield-point effect, and thus the possibility exists here for experimentally ascertaining the importance of short-range order with respect to yield points in these alloys. Since a 12 pct difference exists between the atomic sizes, elastic or Cottrell locking5 must also be considered. Further, Howie and swanne have shown that the stacking fault energy of copper is reduced by aluminum additions. The width of extended dislocations should thereby increase. hus the conditions appear attractive for Suzuki locking.' Finally, the possibility of stress-induced order at dislocations, schoeck locking,' must also be examined, EXPERIMENTAL PROCEDURE Alloys up to 14 at. pct Al were prepared by induction melting high-purity (99.999 pct) Cu and (99.996 pct) Al in a graphite boat under a dynamic vacuum of 5 X 10o mm of Hg. After homogenizing the ingots at 900°C for at least 24 hr under vacuum, they were rolled with intermediate anneals to strips 1.55 mm thick. Single crystals 10 in. long were grown by lowering strips, contained in a split graphite mold sealed in fused quartz at 5 X lo-' mm of Hg, through a single coil induction heater at a constant rate of 1/2 in. per hr. Tensile specimens 1.25 in. long were cut from the single crystal strips and reduced cross sections about 0.7 in. long and 3.0 to 3.5 mm2 in area were introduced by filing and abrading.8 To remove the worked portion about 10 pct of the cross-sectional area was removed by etching. Back-reflection Laue photographs of a filed and etched specimen were taken before and after annealing at 900°c for 24 hr. Small, well defined Laue spots were obtained with no visual difference in the two photographs. Further, specimens with and without the reduced sections began yielding at about the same stress. Hence, for our purposes, filing and abrading did not affect the structure of the specimens. Each single crystal specimen was annealed at 900° c in vacuum for at least 24 hr and furnace cooled; while cooling through the range of 250o to 200°c, the rate was about 55°C per hr. Orientations were determined by the usual back-reflection Laue

Jan 1, 1962

By R. G. Garlick, H. B. Probst

Tungsten single-crystal specimens of various orientations were deformed in tension at room temperature. Slip traces indicated both (112)(111) and (110) (111) slip; however, about 10 pct plastic dejormation was required bejore these traces could he seen. Resolzled shear-stress considerations indicated that at least some of the particular systems observed were not those on which slip initiated hut were secondary systems. This is highly probable, considering the high plastic strains involved. Analysis of the stress data with respect to possible slip systems indicated that slip must have been initiated at stresses below the proportional-limit stresses measured. ALTHOUGH there is general agreement that slip deformation in fcc and hep metals takes place on the plane of close packing and in the direction of close packing, there is no such agreement for slip in bcc metals. It is generally agreed that the close-packed direction (111) is the slip direction, but investigations have led to conflicting descriptions of the slip plane. As Hoke and Maddin1 point out, there are essentially four points of view. 1) Deformation in bcc metals is composite shear on (112) and (110) planes or on nonparallel (110) planes, and any apparent slip on other planes can be accounted for completely by slip on these planes. Chen and Maddin have reported this to be the possible case for molybdenum." 2) Slip occurs in the (111) direction and is limited to {110), {112), and (123) planes (the three closest packed planes of the lattice). 3) Slip occurs in a (111) direction, but not necessarily on planes of close packing (banal slip). 4) Slip occurs in those directions and on those planes for which ß, the ratio of Burgers vector to interplanar spacing, is a minimum. The slip systems of the bcc metal tungsten have never been fully determined, although several investigators have reported pertinent results.3"7 The present work was initiated to determine the active slip systems in tungsten at room temperature, the critical resolved shear stresses associ- ated with these systems, and the orientation dependency of operative systems. These features of tungsten deformation at room temperature have never been reported in the literature. The authors find this somewhat surprising, particularly in view of the availability of tungsten single crystals since the advent of electron-beam zone-melting techniques and the widespread interest in refractory metals. It would seem apparent that such work has been attempted but the results have not been reported, possibly due to the conflict with deformation theory. The results of the present work conflict with any straightforward description of deformation based on the proposed explanations of slip in bcc metals. Although these conflicts have not been resolved, a presentation of the problem seems in order and should be of value to others working in this field. MATERIALS AND PROCEDURE Single-crystal tungsten rods of 1/8-in. diameter were grown from undoped commercial rod by one-pass electron-beam zone melting in apparatus previously described by witzke.8 Representative analyses of the rod before and after melting are given in Table I. There was no detectable zoning of impurities during melting. Buttonhead tensile specimens, as shown in Fig. 1, were machined from single crystals. Two flats 90 deg apart were ground in the gage length of each specimen. These flat surfaces facilitated the analysis of slip traces. No attempt was made to position these flats with respect to the crystal orientation. The worked surface layer of the machined specimens was removed by electrolytic polishing in a NaOH solution. Tensile-axis orientations were determined by standard Laue back-reflection techniques. The sharpness of the Laue spots indicated that the crystals were free of strain.

Jan 1, 1964

By Denton R. Wieland, Harvey T. Kennedy

The frequency of bubble formation is measured for oils from the East Texas field and the Slaughter field in cores from these fields. East Texas oil was also tested in a Slaughter core. The data checked previous results in that a definite supersatrtration may exist without the formation of bubb1es in periods of observation totaling 158 hours. Measured frequencies varied from zero at supersaturations below 14 psi to 3.1 bubbles/sec/ cu ft of rock at 40 psi supersaturation INTRODUCTION The formation of bubbles is essential in a solution gas-drive reservoir in the displacement of oil. In formations where the basic pore structure consists of fine pores or fractures connected to larger pores or crevices, bubble formation in the fine pores may be the most effective means by which the oil may be displaced, even if secondary methods are applied. The most efficient oil displacement would occur where at least one bubble would form in every pore. As the pressure decreased, the bubbles would expand, due to the gas diffusing into the bubbles, and displace the oil toward the lower pressure area around the wellbore. Kennedy and Olson' have shown that the total number of bubbles formed in a reservoir is primarily dependent upon the rate of pressure drop, the rate of diffusion of gas through oil, and surface area of the rock. The surface tension of the liquid and other characteristics of the rock may also exert an important effect, which would give a different frequency to different rocks and oils and various combinations of different rocks and oils. The purpose of this paper is to present frequency measurements on two rocks and two oils. A hydrocarbon liquid is at equilibrium with gas when it contains the maximum volume of gas in solution that it can have at the prevailing temperature and pressure. If the temperature is maintained constant and the pressure is reduced below the equilibrium pressure, the liquid is supersaturated to the extent of the difference in the two pressures until the gas comes out of solution as a free phase. As shown by previous work, and confirmed in the present investigation, the number of bubbles formed per second increases with an increase in supersaturation. Kennedy and Olson showed that a tenfold increase in the rate of pressure decline resulted in a tenfold increase in the number of bubbles formed per cubic foot of reservoir rock, e.g., for decline rates of 0.1, 1, and 10 psi/day, the number of bubbles formed per cubic foot would be 40, 400, and 4,000, respectively. For another hypothetical system, Stewart, Hunt, and Berry' estimated that for pressure declines of 0.1, 1, and 10 psi/day, the number of bubbles formed would be approximately 10, 100, and 1,000 cu ft of reservoir rock. Their value of bubbles formed is lower than given by Kennedy and Olson; however, the order of magnitude agreed satisfactorily. The rate of diffusion will also affect the number of bubbles formed. If the diffusion coefficient is high, the gas in solution in the oil surrounding a single bubble will tend to diffuse into the bubble rather than forming other bubbles. On the other hand, the formation of more bubbles will tend to occur if the diffusion coefficient is very low. In his thesis dated Aug., 1953, Wood" reports on the frequency of bubble formation in a system consisting of oil and rock from the Rangely field. In the present work, the apparatus of Wood was redesigned to allow greater precision, especially at low supersaturations, where bubble growth is slower, and detection is more difficult.

Jan 1, 1958

The earliest record of coal in Indiana is one of the earliest in the country. At the close of the French and Indian War, in 1763, the famous Indian trader, George Croghan, was sent from Pittsburgh on a mission to the western Indians. His party met that of a hostile chief on the lower Ohio and was captured, and were taken up the Wabash River; on June 22nd, he passed the mouth of the Vermilion River-probably the Big Vermilion-and on June 23rd, he made the following entry in his journal: "on the South Side of the Ouabache runs a high hank, in which are several very fine coal mines, and behind this bank, is a very large meadow, clear for several miles."' The mines, of course, were outcrops. A few days after this he met some Indian acquaintances who secured his freedom. This location was at Ouicatanon, 210 miles from "Port Vincent," which was destroyed a few years later, and in what is now Fountain County, probably near Coal Creek. Croghan was familiar with the coal already being worked at Pittsburgh. Surveyors who ran the township and section lines in the first ten years of the last century noted the presence of coal and marked its position on the maps in 1804.2 The next record is by Nicholas J. Roosevelt, who in 1809 examined the Ohio and Mississippi Rivers prior to starting building the first steamboat to navigate these rivers. "Not only did he do this, but finding coal on the banks of the Ohio, he purchased and opened mines of the mineral; and so confident was he of the success of the project on hand, that he caused supplies of the fuel to be heaped upon the shore, in anticipation of the wants of a steamboat whose keel had yet to be laid."3 It is probable that this account confused the date of seeing the coal with that of mining it, as an earlier account by another relative of Mrs. Roosevelt of the first trip of the steamboat New Orleans in 1811 is as follows:

Jan 1, 1942

By H. D. Attra

The effects of phase behavior on reservoir economics is a function of both fluid composition and flow properties of the reservoir rock. In some operations such as gas injection into volatile crude-oil resertoirs, the stock-tank recovery derived from vaporization of the reservoir oil by the displacing gas can approach the recovery derived from the displacement mechanism. In other cases of gas-cycling reservoirs, the dry injected gas can effectively vaporize a retrograde liquid phase, allowing a substantial reduction in cycling pressure with no appreciable loss in recoverable liquids. Because of these effects, it is essential that phase behavior be considered in developing the economics of any secondary recovery program in which gas is the injected fluid. The inclusion of phase behavior in conventional calculation procedures has been retarded because of the complexity of the calculation and the large volume of laboratory data required. However, by applying high-speed computers and new laboratory techniques, the phase-behavior displacement calculation has been developed to economically include this basic fundamental of gas displacement. The calculation is performed by reducing the reservoir to a series of one-dimensional segments. Phase changes, saturation distributions and changing fluid properties are evaluated for each segment as a function of time. The relative volumes of equilibrium liquid and gas displaced from each segment are determined by a trial-and-error procedure to meet the requirements of phase equilibrium and two-phase flow. The produced fluids are flashed through conditions of surface separation approximating those in the field to obtain actual values for stock-tank liquid recovery and producing gas-oil ratios. Based on the results of successful field studies, the technique appears to have application to reservoirs producing under a nonmiscible gas-displacement mechanism and should substantially increase the reliability of this type of analysis when phase behavior is an important factor. Predicting reservoir performance under gas-injection operations involves three basic principles of reservoir engineering. First, a material balance exists between the displacing gas and the displaced reservoir fluid. Second, the oil and gas flow in relationship with the two-phase flow property of the reservoir rock; and third, phase equilibrium exists between the displacing gas and the native reservoir fluid. To illustrate these three principles, consider the one-dimensional reservoir shown in Fig. 1. The reservoir is divided into a series of segments representing a one-dimensional cross section between an injection area and a producing area. So represents the oil saturation, Cw represents the connate-water saturation and Sg represents the displacing gas saturation. The gas is moving into Segment 1 and the reservoir oil is being produced out of Segment N. Consider the case when gas has just moved into Segment 1 and the displacing gas-oil contact is at position a-a The volume of oil pushed out of Segment 1 is a function only of mobility and the two-phase flow properties of the reservoir rock, that is, Kg/Ko and µo/µg. Behind the front if the injected gas is foreign to the reservoir oil (a nonequilibrium gas), there will either be vaporization of the oil into the gas or condensation of the gas into the oil. In either case the net result is a mass transfer and a re-distribution of composition and liquid and gas saturation. If the displacement is at constant pressure and is continued, the gas moves into new segments, proceeding succesively into Segment 2, 3, etc. The total volume of oil produced from the reservoir

By J. L. Bruce

For a number of years, from an economic standpoint, the ventilation of the Colorado mine of the Davis-Daly Copper Co. has been a difficult problem. The development through the main hoisting shaft was pursued for a number of years and to a depth of about 2500 ft.( 762 m.)before large bodies of good commercial ore were opened up. This lack of early success in exploration restricted expenditures for ventilation, with the result that the present orebodies were opened up at a depth of 2500 ft., and in country rock f relatively high temperature, without adequate means f supplying the development faces and the stopes with cool or fresh air of low humidity and suitable velocity. During the progress of development, two or three connections were made at higher levels with the workings of adjoining operations, but these were of a makeshift and unsatisfactory character and afforded no means for carrying downcast air from the surface, in anything approaching a direct course, to the working faces. During the latter part of 1917, arrangements were made with. the Anaconda Copper Mining Co., whereby, during the year 1918 and the early part f the year 1919, a crosscut was driven eastwards on the 2500-ft. level of the Colorado shaft and connection was made by means f an up-raise of approximately 200 ft. to a crosscut driven westwards from the 2800-ft. level of the Belmont mine, this crosscut at the top of the raise being driven at Davis-Daly expense by the Anaconda Copper Mining Co. This connection, in conjunction with a No. 11 Sirocco fan installed near the Colorado shaft, provided the Colorado mine with a maximum of approximately 30,000 cu. ft. per min. of relatively fresh air, most of which came in a fairly direct route from the downcast Belmont shaft through the No. 11 fan to the 2500-ft. level stopes. After passing through these stopes and the stopes of overlying levels, it passed through the main crosscuts on higher levels back to the Colorado shaft, which provided the upcast for this current of air. The improvement

Jan 9, 1921

By Owen F. Devereux

Two discrete types of microstructure me seen in cermets formed by the reaction: 4Al (liquid) + 3SiO2 (glass) — 2A12O3(a) + 3Si (solid) Relatively coarse-grained macroscopically isotropic specimens resulted from reaction with aluminum containing appreciable silicon, while macroscopically anisotropic fine-grained specimens were formed by reaction with aluminum low in silicon. Optical microscopy, electron microscopy, and X-ray diffraction suggest that the anisotropic material contains gross areas in which submicroscopic grains of a A12O3 are oriented along radial lines drawn from the specimen surface. These lines are presumed to originate at defects in an otherwise protecting surface layer. A unique cermet is formed by the reduction of high-silica glass by molten aluminum according to the reaction: 4A1 (liquid) + 3SiO2 (glass) — 2A12O3 (a) + 3Si (solid) The free-energy change accompanying this reaction is -150 kcal at 800°C; the volume change (volume of A12O3 and silicon minus volume of SiO2) is +6 pct. The reaction product, however, contains aluminum metal as well as Al2O3 and silicon because some of the product silicon is dissolved in the aluminum bath and is replaced by aluminum in the structure. The product is a hard gray solid that retains the external dimensions of the original silica article. The system has been studied in the past, the investigations culminating in patents to George1, 2 and Saw-chuk., The former emphasize that this reaction is but one of a relatively broad class of such systems, while the latter demonstrates that a marked improvement in the gross physical properties of the cermet can be obtained by dissolving appreciable quantities of silicon in the aluminum reactant. The system has also been studied by workers at Rolls Royce Ltd.,4-6 who have patented the addition of small quantities of arsenic, antimony, bismuth, or phosphorus to the reactant bath to SO impede the reaction that glass fibers may be metal-coated by immersion in molten aluminum.

Jan 1, 1969