Search Documents

By R. P. Carreker

THE experiments described in this report were conducted as a part of a general program designed to document the deformation behavior of pure metals over a wide range of temperature. Material The silver used in this investigation was obtained from the Handy and Harmon Co. as 99.97+ pct pure. It is from the same length of wire as that designated H-H silver by Hoffman and Turnbull in their investigation of self-diffusion in silver.' The silver was drawn at room temperature from 0.060-in. diam to 0.020-in. diam wire without intermediate annealing. Seven-inch lengths of cold-drawn wire were annealed in groups of ten by placing them in individual quartz tubes spaced circumferentially about and near the vertical furnace axis. Dry nitrogen was passed through the furnace to lower the partial pressure of oxygen. The three annealing temperatures used were 700°, 800°, and 900°C, producing grain sizes of 0.017, 0.040, and 0.250 mm diam after 30 min at temperature. Testing Procedure The details of the testing procedure have been described in the reporting of results of a similar investigation of Copper. Annealed specimens of 5-in. gage length were gripped between grooved plates. Tests were performed using an Instron tensile-test-

Jan 1, 1958

By E. N. Cameron

Graphite has been included in U. S. lists of strategic minerals since the problem of mineral deficiencies was revealed during World War I. Since 1918 the domestic graphite industry has led a precarious existence, and there has been much uncertainty as to the amounts of usable graphite of various grades that would be available from domestic sources in time of emergency. In 1950-1951 therefore, the writer, assisted by Paul L. Weis, undertook a review of domestic graphite sources for the U. S. Geological Survey. The conclusions of this study are presented here, with a discussion of some technologic and politico-economic factors bearing upon the problem. Uses of Graphite: Natural graphite as marketed exhibits a wide range of properties, which determine the uses to which it is put. The most essential uses are in the manufacture of crucibles and related refractory articles, in lubricants and packing materials, and in the manufacture of batteries, foundry facings, pencils, and carbon brushes. Numerous specifications covering the mineral in its various applications must be met by producers and processors of graphite. The problem of supply is therefore not simply one of procuring a sufficient total tonnage, but the more difficult problem of procuring enough of each different grade to meet foreseeable needs.

Oct 1, 1956

By Harold B. Goldman, Don Reining

The sand and gravel industry is the largest nonfuel mineral industry in the nation (Drake, 1972), Table 1. In 1970, the production of sand and gravel totaled 944 million tons valued at $1.1 billion. California, which leads the nation with more than 140 million tons, together with Michigan, Ohio, Minnesota, Illinois, Wisconsin, and New York, account for 43 % of the total production in the nation. In commercial usage, "sand" applies to rock or mineral fragments ranging in size from particles retained on a No. 200 sieve (0.074 mm openings) to those passing a No, 4 sieve (4.76 mm openings). "Gravel" consists of rock or mineral fragments larger than 4.76 mm, ranging up to 3%-in. maximum size. The construction industry consumes 96% of the sand and gravel produced; the remainder is sand used for specialized products such as glass (see the chapter on "Silica and Silicon"). Utilization The building industry uses sand and gravel chiefly as aggregate in portland cement concrete, mortar, and plaster; the paving industry uses sand and gravel in both asphaltic mixtures and portland cement concrete. Aggregate is commonly designated as the inert fragmental material which is bound into a conglomerate mass by a cementing material such as portland cement, asphalt, or gypsum plaster.

Jan 1, 1975

By Will B. Jamison

Man's material advance from one level of civilization to the next has involved the development of new, more useful tools and the utilization of energy greater than he alone could produce. These two essentials for material progress have developed at an ever increasing rate in the last century. While the first really successful use of mechanical energy derived from burning fuel was in James Watt's steam engine which pumped water from coal mines in Cornwall about 1770, there was still very little use of mechanical energy in mining by 1900 except for pumping and hoisting. Compressed air, having some of the characteristics of steam and which operated engines not unlike steam engines or steam hammers, powered the first attempts to mine coal with energy greater than human muscle could provide. When direct current-powered traction cars replaced horse-drawn transportation cars on city streets, it was natural that direct current locomotives should begin to replace animal and human power in mine haulage. Slowly, trolley and battery locomotives were developed and introduced. With d-c systems being established for haulage, it was natural that improved cutting machines should be developed and powered by d-c motors. Thus began the years of

Jan 5, 1960

By Hugh D. Pallister, Richard W. Smith

The Alabama flake-graphite industry has flourished only in times of war when importations of foreign graphite for crucible use have been greatly curtailed or cut off. World War I was a boom period and in 1918 some 30 plants produced 7,795,475 lb. of flake graphite. The industry languished following the war and no graphite was produced from 1929 to 1939. The Federal Bureau of Mines began investigating the Alabama graphite deposits in 1940 and worked out modern recovery methods that were applied to production during part of World War II. A prospecting program disclosed reserves of over 25 million tons of graphitic schists. In 1942 the War Production Board authorized the enlargement of the only plant then producing flake graphite and the construction of two new plants. Production of flake graphite from these three plants in 1943 is estimated at 8,100,000 lb. Increased imports from Madagascar late in 1943 shut down one of the new plants and curtailed production at the other. Alabama flake graphite has not yet been able to compete with Madagascar graphite for use in the manufacture of any but small graphite crucibles. The future of the industry must depend on meeting the higher carbon content demanded for other uses.

Jan 1, 1945

By Nicholas J. Grant, Ulf Kalling, John Chipman

THE operation of a blast furnace is dependent to an important extent upon the sulphur content of materials charged and the desired limit of sulphur in the product. It has long been known that the blast furnace is the most efficient tool for desulphurization in common use and that this efficiency is associated with the strongly reducing conditions of the hearth and is enhanced by increased basicity and fluidity of the slag. The chemical reactions of desulphurization may be studied from the viewpoint of the ratio of the process or of the final equilibrium conditions. Both kinds of studies contribute to an understanding of the process and both are included here. A simple measure of the desulphurization power of a slag is given by the ratio: Pct sulphur in slag (Pet S) Pct sulphur in metal [Pct S] This ratio was used by Holbrook and Joseph',' to measure relative desulphurizing powers under controlled laboratory conditions. It was also used by Hatch and Chipman3 as a measure of the equilibrium distribution. For the latter purpose it would be preferable to employ thermodynamic activities rather than percentages, but until very recently this has been impossible for lack of data. Now, thanks to the work of Morris and Williams and Morris and Buehl," the effects of carbon and silicon upon the activity of sulphur in the metal are known. The confirmation of this work and its extension to include the effects of other elements by Sherman and Chipman and by Rosenqvist and Cox' make it possible to calculate the activity of sulphur in pig iron of any composition. Hence it is now possible to use data on the equilibrium distribution of sulphur to find its activity in the liquid slag and to approach an ultimate solution of the thermodynamic aspects of the problem. The rate of transfer of sulphur from metal to slag is the problem of major industrial importance and indeed the principal need for equilibrium data has been as a necessary adjunct to the kinetic studies. The rate of approach to equilibrium under laboratory conditions seems slow compared to the requirements of industrial practice, and it is clear that further laboratory studies of rates are needed. In the research reported below, the items which were investigated were the following: I—The role of mechanical stirring on the approach to equilibrium. 2—The role of MgO in desulphurization as compared to CaO. 3—The role of MnO in desulphurization. 4— The limiting reactions which constitute the slow steps in desulphurization. Experimental Procedure The experimental set-up and procedure previously described by Hatch and Chipman" were essentially followed with several small modifications. The graphite crucible containing the slag and metal charge was altered to provide considerably more active stirring and mixing of the slag and metal in the carbon monoxide atmosphere. For this purpose the crucible was machined to provide two deep cylindrical wells which were interconnected at top and bottom as shown in Fig. 1. A graphite screw with a flat thread and of shallow pitch (4 threads per in.) spinning at 600 to 800 rpm was used to lift the slag and metal over the partition between the two wells and throw them over into the second well, where the metal settled through the slag into the reservoir at the bottom. It was possible to see actual particles of slag and metal being thrown over the partition. In this respect, the stirring was more vigorous than used in the work of Hatch and Chipman. A charge of 400 g of wash metal was first melted, and 20 g of FeS was then added to yield a bath containing 1.65 pct S. Immediately 400 g of slag (as pure mixed oxides) was added and fused. The slag was generally fused in 1 hr * 10 min. Within 30 to 45 min after melting, the temperature was adjusted to 1525"C, and the first slag and metal samples were taken. The slag was picked up on the end of a cold Armco iron rod, whereas the metal was sucked into a silica tube. The wash metal composition was (in percent): 4.29 C; 0.022 S; 0.021 P; 0.38 Si. The slags used were of four fixed starting compositions covering a wide range of acid-base ratios shown in Table I. Deliberate variations in MgO were made in these slags to check the role of MgO in blast-furnace desulphurization. Changes due to additions and reactions were followed by analysis of samples. Additions of Mn and MnO were made to most of the heats to note the role of Mn and MnO on desulphurization. Three heats (62 through 64) were made in an open pot induction crucible (graphite) using a

Jan 1, 1952

By J. C. Bradbury

The year of the Centennial is upon us. Not only is AIME marking its 100th birthday, but the cement industry is also celebrating 100 years of activity (see article by Roy Grancher, page 48). Fort Dodge, Iowa, and gypsum also tried to get into the act but missed by one year. Frank Apple-yard's gypsum article (page 53) informs us that the Fort Dodge area has been producing gypsum continuously for 99 years. That would seem to make AIME and the industrial minerals doddering oldsters. Not so-our Institute shows more energy than ever, and the word for industrial minerals is growth. These are the mineral resources of the future, the raw materials for the abundant life to come

Jan 1, 1971

By John Gillie

Prior to the year 1902 electricity was used in the Butte district only for lighting, for the tramming of ores on the surface, and for the electrolytic refining of copper. In that year the Canyon Ferry hydro-electric plant on the Missouri river, with a transmission line to Butte and Anaconda, was completed, and enabled the mining operators to purchase electric current in large quantities at reasonable rates, and its application and use in the various mining operations and reduction works proceeded rapidly. The principal applications. of electric current in metal mining may be listed as follows: Compressing air for hoisting. Compressing air for rock drills and pneumatic tools. Pumping. Ventilating. Lighting. Tramming. Compressing air for blast furnaces and converters Running shop and miscellaneous motors.

Jan 9, 1913

By E. Amott

A test is described in which the wellubility of porous rock is measured as a function of the displacement properties of the rock-water-oil system. Four displacemet operations are carried out: (I) sponlaneous displaceti?ent of water by oil, (2) forced displacement of water by oil oil in the same system using a centrifuging procetllrre, (3) spontaneous displacement of oil by water. and (4) forced displacment of oil by water. Ratios of the spontaneous displacement volumes to the total displucenlent volumes are used as wettability indicates. Cores having clean mineral surfaces (strongly preferentially water-wet) show displacement-by-waler ratios approaching 1.00 and displacement-by-oil ratios of zero. Cores which ([re. strongly preferentinlly oil-wet give the reverse resu1ts. Neutral wellability cores show zero values for both ratios Fresh cores from different oil reservoirs have shown wettabiltties in tlris te.st covering rrlti~ost 111e conlplrtt, range of thr: te.st. Notvever, nlo.s/ of tlle fresh California cores tested were slightly prcfere111icrlly wclter-\vet. The chrrnge.~ in coro u ('liabilities, as indicated hy this te.st, r~.sril/ing from various CO~P hanrlling procedures tt,ere oh.served. In sonie ca.sc,s /Ire ~,cttahilitio.c. of fresh cores were changell by drxi:~g or 11y e.x/rclct ing with iolcreiii~ or. dioxunc~; in o/h~r cases they were 1101 changed. Co~ltrrc/ of cort,.s ~.ith filtrc~t~c. from water-base rlrilling rilrrrls crlrc.sed littlc change in we/ /ahility ivhile contnct with filtrates frorii oil-hus~ ri1rlcl.s tlecrrascrl the prefcrerlcc, of the, cores for )I.NI Usitig thi,s test to ri.crl~lute n~r~ttubili~y, N .vt~ldy was iilarle of /lie correlmtio~i of wettability with wa/erfloocl nil recovery for orttcrop Ohio sand.stone and for Al~ln-tlunl. Resul/.v indicate thml no single correlatioti between these factors applies to different porous rock syste~n. It is thought that diflerences in pore gen~netry resrrlt in diflrrerrce.~ in this correlurio~z. INTRODUCTTON Most investigators who have reported on the wettahility of porous rock have described such rock as prcferentially water-wet or preferentially oil-wet. In some cases a third classification, neutral wettability. has been used. The efficiency of water floods in each of these wettability groups has been described in numerous publications. Several methods for characterizing porous rock wet tability more precisely have been reported,' " but it appears that because of one weakness or another. none of these has been generally accepted. Early in our studies in this field, it was found that the displacement efficiency of oil by water in a particular porous rock having a strong preference for water was quite different from that in a similar rock having only a moderate preference for water. Thus, there appeared to be a need for a practical, reasonably precise wet tability test. one which could classify porous rocks into 10 to 20 different groups rather than the two or three broad groups listed above. The test developed to meet this need is described in this paper. Also, changes in wettability, as indicated hy this test, resulting from various core handling procedures are discussed. Finally, data showing the corrclation of wettability with waterflood oil recovery for two different types of cores are presented and discussed. Some confusion has resulted from the failure of certain writers to define clearly some of the wettability terms they have used. Accordingly, the following commcnts concerning definitions are offered. The wc t ta-hility of a solid surface is the relative preference of that surface to be covered by one of the fluids under consideration. It is felt that this is the generally accepted definition. The fluids being considered must bc specified (or understood) before the term wettability has any significance. In the work reported here these fluids are water (3 per cent brine) and oil (kerosene). The term preferential wettability is sometimes used, but we think that the word preferential is redundant here and should not be used. Tn line with the definitions of Jennings', a preferentially oil-wet solid surface is regarded as a surface which will show an oil advancing contact angle less than 90" (measured through the oil) in the water-oil-solid system. Oil will spontaneously displace water, if both are at the same pressure, from such a surface. A preferentially water-wet surface is analogous. This is consistent with the wettability definition above. As Jennings has said, frequently the term oil-wet is used to mean the same thing as preferentially oil-wet. However, oil-wet also has been used occasionally referring to an oil-covered surface when the availability of water was limited. To avoid confusion from this source, we do not use the terms oil-wet and water-wet. DESCRIPTION OF WETTABTLITY TEST The following points were considered desirable in a wettability test for our purpose. 1. The test should be a displacement test resembling

By G. N. Panagiotou

SIMPTOL, a computer simulation program written in FORTRAN IV for use with Cyber 171/8 System at the National Technical University of Athens, describes the mining operations in an opencast lignite mine operating Bucket Wheel Excavators, Conveyors and Stackers. The central objective of the program is to aid management in the selection of a BWE-Conveyor-Stacker System for a given lignite deposit and equipment layout. Much information can be gained from the program with proper manipulation of the input data, which refer to mining profile, soil characteristics, equipment specifications and availabilities and time study data. The other objective of the program is to aid production scheduling in terms of forecasting production rates of the system. The program has been applied to Kardia lignite mine to evaluate its usefulness to represent the actual situation of the system being simulated.

Jan 1, 1983

By Fred C. Bond

IN crushing and grinding the larger particles are more exposed to the work input. They absorb most of the work and protect the smaller neighboring particles from destructive contact with the crushing surfaces or grinding media. The importance of this exposure differential upon the reduction efficiency and product size distribution has long been recognized. Unfortunately, there has heretofore been no direct method of evaluating it, and such indirect methods as observing the slope of the plotted product size distribution line have been used as an indication. In this presentation the Third Theory of Comminution1 has been used, together with the exponential formula for size distribution, to evaluate the exposure ratio and exposure constant and to illustrate examples of their utility in crushing and grinding applications.

Jan 12, 1957

By W. A. Longacre

IN the geophysical exploration program of the Cleveland-Cliffs Iron Co. on the Marquette Range of Northern Michigan, the vertical intensity magnetometer has been used to obtain magnetic anomaly maps of large areas. A network of magnetic base stations has been established and the relative vertical intensity at each station measured carefully with respect to a prime base. In the search for the relatively nonmagnetic soft red hematite ore, the magnetic exploration is indirect, involving the study of dikes, faults, contacts, and other structural features. It was found that the magnetometer, adjusted to a scale value of approximately 40 ? per scale division, was satisfactory for this type of exploration, although many magnetic anomalies were encountered that required the use of auxiliary magnets.

Jan 1, 1952

By W. A. Longacre

IN the geophysical exploration program of the Cleveland-Cliffs Iron Co. on the Marquette Range of Northern Michigan, the vertical intensity magnetometer has been used to obtain magnetic anomaly maps of large areas. A network of magnetic base stations has been established and the relative vertical intensity at each station measured carefully with respect to a prime base. In the search for the relatively nonmagnetic soft red hematite ore, the magnetic exploration is indirect, involving the study of dikes, faults, contacts, and other structural features. It was found that the, magnetometer, adjusted to a scale value of approximately 40 y per scale division, was satisfactory for this type of exploration, although many magnetic anomalies were encountered that required the use of auxiliary magnets.

Jan 10, 1951

By Donald R. Williamson, Edward R. Mueller

Cyprus Pima Mining Co.'s open pit operation was started in 1957 with the normal assumption that the ore reserve estimate was accurate within an acceptable range of values. Over the years, a number of attempts have been made to refine and polish the ore reserve figures using a variety of established standard procedures. None of these attempts have produced results which are totally satisfactory, particularly when comparisons are made between ore reserve estimates and short to medium range production figures. Statistical studies of operations data revealed relationships which could be used to subdivide ore blocks in much the same way as they are actually mined. Comparisons between these newly developed ore blocks and production data show that the new method of evaluation yields excellent results.

Jan 1, 1978

By J. Charles Miller

THE expansion of facilities for rapid transportation of perishables by train, truck and airplane has necessitated consideration of refrigerants of a minimum weight and volume per pound of cooling and has stimulated the use of solid carbon dioxide commercially. The gas probably has not had wide application in the past in air-cooling equipment for mines, theaters or buildings, owing to its thermodynamic properties, as will be deduced from examination of Table 2. However, consumption of the liquid in carbonating beverages remains a dominant factor. In addition to these uses, carbon dioxide is employed to a limited degree as an explo-sive in the liquid form, as a freezing agent in plumbing, in laboratories for low-temperature work, and in the manufacture of golf balls.

Jan 1, 1936

By Gareth Thomas

The analysis of Kikuchi pattersns of exct ovientalions from single cryslals and paired Kikuchi lines from single and overlapping crystals is shown to be useful and quanlitalve and is applied to Phase transfovnzcitions including ordering, spinodals, mavten-silic, and nuclealion and growth pyocesses. 112 pinciple, the analysis of exacl orientations enables the crystal system and the Bravais lattice of a crystal to he determined. The advantages of the davk-field imaging technigure for detecting vevy small precipitates are also described. ALTHOUGH Kikuchi electron-diffraction patterns were first observed nearly 40 years ago,' little systematic application seems to have been made of them, until fairly recently during electron microscopy, when their usefulness in contrast experimen and for determining exact orientations8'9 has been pointed out. With the availability of gonio-metric specimen tilting stages it has now become possible to make much wider use of diffraction patterns, particularly the Kikuchi pattern, which is the main subject of this paper. The treatment presented here is not exhaustive but it is hoped that it will stimulate more use of Kikuchi patterns during electron-microscopy investigations. The Kikuchi pattern is formed as a result of Bragg diffraction of the inelastically scattered electrons produced during the interaction of the beam and thick specimens, The important feature of these patterns is that they give an accurate representation of the symmetry of the crystal being investigated, so that it is possible to identify crystal systems and even the Bravais lattice. This means that new structures, e.g., formed in phase transformations, may be identified during normal electron microscopy, so that Kikuchi-pattern analyses considerably extend the uses of the electron microscope. Recent work has also shown that dark-field images are more informative than bright-field images, particularly, for observing small precipitates. The second part of this paper discusses some applications and advantages of dark-field imaging in studies of two-phase systems. 1) DIFFRACTION PATTERNS 1.1) Spot Patterns. Electron-diffraction spot patterns have their limitations because of the importance of the form factor on the intensities and shape of the reciprocal lattice points. Because of the extension of these points into relrods, reflections are possible over a large angular range (+5 deg) and the patterns from thin regions can be complicated because second-layer relrods intersect the reflecting sphere. Spot patterns can thus give only an approximate idea of the crystallography unless the foil is tilted into exact orientation. In this case the spot pattern is symmetrical, with equal numbers of spots on the positive and negative zone directions about the origin. Such cases are necessary for structural analyses and have been used recently to determine the crystal structure of the ordered Ta64C phase." Exact orientation means that the plane of the reciprocal lattice lies exactly normal to the incident beam as shown in Fig. 1(b). It should be noted that in exact orientations the angle of reflection is less than the exact Bragg angle 9 so that the reciprocal lattice points lie to the outside of the sphere, Fig. 1(b). This deviation is denoted by the parameter s and in the usual convention4 s is negative for exact orientations and, of course, zero at the exact reflecting position shown in Fig. l(a). In order to avoid secondary reflections from thickness relrods it is advantageous to work in thicker regions of foils. Diffraction from thick regions may also produce Kikuchi patterns and as dis-

Jan 1, 1965

By Christopher W. Schram, Allan B. Tanner, Frank E. Senftle, George R. Boynton, Philip W. Philbin

A borehole sonde using a 252Cf neutron source and a Ge(Li) gamma-ray detector was field tested in a coal bed in Belmont County, Ohio, to ascertain whether such a device could be useful as a coal-exploration tool. As the sonde was lowered into the borehole, successive spectra were accumulated over short time intervals. The intensities of the capture gamma rays from hydrogen and of decay gamma rays from aluminum were determined simultaneously in each spectrum. A log of the intensities versus depth shows the depth and thickness of the coal bed. With the sonde stationary at points above, in, and below the coal bed, capture gamma rays were measured to show the variation in concentration of certain elements. From the spectrum recorded in the bed, a complete ultimate analysis, the percent ash content, and the heat content were determined without recourse to an external standard. Delayed gamma-ray analyses of the core were also made on the surface in the vicinity of the borehole in a fixed-geometry irradiation facility wing the detector in the borehole sonde. The concentrations of 10 elements were determined by this method on a coal split from the drill core. These experiments show that it is feasible to use a 252Cf- Ge(Li) borehole sonde as an aid in coal exploration.

Jan 1, 1979

By Roy E. Gilbert

IN what ways can conventional geophysical methods be used in the search for quartz-sulphide veins covered by several feet of overburden? The New Park Mining Co., in search of an answer to this question, empirically tested simple geochemical, electrical, and magnetic methods over known ore bodies and geologic structures. Geochemical methods were the only ones found to be applicable to direct ore search. Indirect uses were found for electrical and magnetic tests. Experiments were conducted in the southeastern part of the Park City mining district. Ore in this part of the district is found principally in steeply dipping veins which are localized along faults and fractures that cut Paleozoic sediments and quartz diorite intrusives. Extensive soil cover effiectively hides both veins and country rock. The type of vein most likely to

Jan 1, 1953

By A. Tremari, Paul I. Eimon

Photogrammetrists are studying with new interest the problems of mine mapping and mining engineers are beginning to see what photogrammetry can do for them. Administrators in a number of European and U. S. mines have tried photogram- metric methods and are finding that better maps and data, needed for mine development, can be produced with savings of time, men, and money. In addition to wide use in small scale mapping projects, photogrammetric methods are now used for producing large scale plans and maps in German coal and lignite mines, in some U. S. open pit mines, to inventory TVA coal stock piles, and to compute highway excavation volumes. In each case surveying and map compilation has been made more efficient and accurate by photogrammetry and at significant savings over ground methods.

Jan 5, 1959

By Nicholas M. Short

Many a geologist or driller has wished he could somehow climb into a borehole to see for himself what fractures looked like. Or why recovery was poor. Or how the bit was actually lost. Now it is possible to do the next best thing to climbing into the hole. TV cameras are being used for a close-up look at borehole conditions. Ever since television was invented, geologists and others interested in subsurface conditions have wanted a TV camera that could be used in the narrow confines of a borehole. But development of such a camera was slow, mainly because of the need for compact size. Not until the late 1950's did the technology of electronic miniaturization develop to a point where a camera satisfactory for the purpose could be put together.

Jan 1, 1963