Search Documents

By W. C. Meyer

In an effort to conserve and extend oil resources, the use of powdered coal-in-oil mixtures (COM) as an alternate fuel in oil-fired boilers is receiving increasing attention. For the approach to be successful, some degree of stability of the suspension against settling is needed. The variety of means available to achieve stability of this nonaqueous slurry is reviewed along with some of the physical and chemical concepts which underlie each method.

Jan 1, 1983

By D. J. Spottiswood, C. N. Robinson, D. E. Spiller, E. G. Kelly

This paper describes the performance of a new design of spiral that is optimized for fine coal cleaning. Reduced Performance (Tromp) curves are presented to compare this spiral with the older design, as well as with other commonly used coal cleaning equipment. As an aid to equipment selection and circuit design, data are also presented to show how variables, such as flow rate, pulp density, and particle size, affect efficiency and the separation specific gravity.

Jan 1, 1985

By Donald P. Richards, John F. Abel

Geotechnical site investigation for new mine shafts can reduce the level of design uncertainty for shaft linings. The parameters which determine the lining strength required include rock strength and hydrologic properties, the in situ stress conditions, and the concrete strength. These parameters are applied to analytical methods of shaft lining design using the plastic and clastic assumptions of rock response to determine the required lining thickness to maintain the stability of the shaft excavation.

Jan 1, 1982

T. R. HARRISON, Washington, D. C. (written discussion *).-Ad-vantage will be taken of this occasion to mention briefly a form of double potentiometer which has been used at the Bureau of Standards for about 2 1/2 yr. in calibrating thermocouples. The calibrations referred to are those made by comparison to standard couples. In order to insure equality of temperature between the couples, the junctions are fused together; consideration of fundamental principles will show that this introduces no error. Two separate potentiometers are used, one connected to each thermocouple, and each potentiometer is provided with a reflecting galvanometer. The two spots of light are reflected on to a single scale, the galvanometers being set in such a position that the spots coincide on the scale at a point marked zero when the circuits are open or when the potentiometers are balanced. By setting one potentiometer to a desired value and adjusting the other so that both spots pass across the scale together as the temperature rises or falls, simultaneous readings are obtained. By making observations first with a rising temperature and then with a falling temperature, the rates of rise and fall being approximately equal, and taking the means of the results found, several minor errors such as those clue to differences in the time lags of the two systems, etc., are eliminated or greatly reduced. The differences between the values

Jan 12, 1919

Discussion of the paper of EDGAR L. NEWHOUSE, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin: No. 92, August, 1914, pp. 1801 to. 1806. G. C. RIDDELL, East Helena, Mont.-As nearly as I can recall at the present moment, there are only four or five large plants on the continent where the lead on charge is carried in the neighborhood of 40 per cent. These are at Herculaneum, Collinsville, and Federal, Ill.; Trail, B.. C.; and East Helena, Mont. Our object at the latter point is to smelt a maximum amount of Coeur d'Alêne lead sulphides in as compact and self-fluxing a charge as possible, and to this end we are now smelting a mixture that at times carries up to 42 per cent. lead. The monotony of producing the 7,000 tons of bullion shipped each month to. the Omaha and Chicago refineries is relieved somewhat by the fact that the 15,000 tons monthly of Coeur d'Alêne ores that are com-ing to us carry enough zinc to provide the one-half slag used with from 6.5 to 7.5 per cent. zinc clay after day. During the month of March, 1914, three lead furnaces in continous operation, each 136 in. long, averaged 249 tons per furnace clay, exclusive of coke and slag shells, which is smelting at the rate of 5.5 tons per square foot of tuyère area. The

Jan 11, 1914

By R. D. Reiswig, D. J. Mack

THE use of pyrophoric alloys in ignition devices dates back more than fifty years to a German patent granted to Carl Auer von Welsbach in 1903.' This patent named a composition essentially the same as that used in most present-day cigarette lighter "flints:" 70 pct mischmetal, 30 pct Fe, referred to here as "Auer alloy." Among the few current exceptions to this composition are those "flints" based on titanium or zirconium. The rare-earth metals of which mischmetal is composed are so similar chemically and physically remarkable similarity in their alloying behaviors would be expected. Comparison of the binary phase diagrams2 of these elements with nonrare-earth metals shows that this is true to a striking degree, so much so, in fact, that it appears that a mixture of these elements may be treated as a single component of alloys without fear of serious error. In considering alloys containing mischmetal, therefore, the mixture of rare-earth elements will be referred to merely as "cerium," the predominant element in mischmetal. In polishing cerium alloys for metallographic examination, it was soon discovered that aqueous polishing media were highly corrosive. Free cerium in the alloys acts similarly to calcium (though not quite so rapidly) in evolving bubbles of hydrogen at the metal-water interface; thus, special metallographic techniques are required. The simplest polishing technique found to be satisfactory consisted of slow hand grinding on dry emery papers through

Jan 1, 1956

By A. R. Oltrogge

WE have just seen? that resistance is a characteristic of an electric circuit that makes it difficult for current to flow; also, that if, by the application of voltage, we cause a current to flow through a circuit having resistance, heat is generated. This is the principle utilized in the production of heat by electric power in the arc furnace. In order to fully appreciate the problems of the arc-furnace electric circuit, let us examine the characteristics of some of the more commonly used materials that offer resistance to a flow of current and thereby produce heat. Usually the resistance material is a metal or a metal alloy, such as the nichrome ribbon in an electric toaster or the tungsten filament of an ordinary light bulb. These are the materials whose resistance-remains relatively fixed and which therefore permit the flow of a definite amount of current for a given impressed voltage. If we want more current to flow, we must either decrease the resistance or increase the voltage that is causing the current to flow. Such a resistive material has what we call a positive volt-ampere characteristic, which means that in order to get more current we must apply more voltage, and in order to reduce the current we must reduce the voltage. Such a volt-ampere characteristic can be represented by a line plotted on a graph (line B, Fig I).

Jan 1, 1947

By Alan Morris

IMPINGEMENT attack, as one of the types of corrosion suffered by condenser tubes, has been given a prominent place in corrosion literature of recent years. It has been reproduced and studied in carefully controlled laboratory tests. Much has been learned of its mechanism, and of the effects of variables such as temperature, amount of air, size of bubble and water velocity. Incidentally the technical public has been given comparisons between the behavior of some few metals under various conditions of impingement attack. The tests recorded here were undertaken in an effort to find at least some sort of qualitative answer to questions which arose occasionally as to the relative resistance of various alloys to impingement attack, and which could not be answered by reference to the literature. The final decision to start work on the problem was influenced in large measure by the nature of the water available in this particular place. The mill of the Bridgeport Brass Co. is located on the Pequonnock River at Bridgeport, Conn., within two miles of its mouth. The water is much like many other estuarine sources which are used in condensers, and which cause particularly severe corrosion. It seemed a most suitable water to use in such tests. As the work progressed an important seasonal variation was noted. The purpose of this note is to record this seasonal effect. The results of individual tests are given only incidentally.

Jan 1, 1931

By H. D. Hoskold

DuRing the last few years, various persons have been put forward as originators of some mechanical device for the purpose of finding distances without the use of a chain or other linear measuring-instrument, and among these, the Englishman, Gascoigne, 1639, is prominent as the first in England; while James Watt, 1771, and William Green, 1778, are also included in the list of inventors. It is possible that this useful and important problem occupied the attention of others prior to the date cited, and, consequently, it is difficult to decide what nation first gave birth to the inventor of an instrument for the object under consideration. A very important work appeared, not long since, in Paris, devoted to a history and discussion of some of the older and newest forms of surveying-instruments,* and at page 79 of that work a curious old instrument is exhibited, called Bigonometre, i. e., an instrument for finding distances and solving trigonometrical problems. in surveying. A copy of the diagram of the instrument exhibited in the book referred to is represented in Fig. 1. Having had an occasion to read the French work referred to, I communicated with the author of it, and he was good enough to reply that he found a diagram of this old instrument in a book published in 1597, by Danfrie, existing in the library of the Academy of Sciences, in Paris. Col. Laus-

Jan 1, 1904

By Ralph Wilcox

The diamond drilling of certain characters of unstable rock formation, as, for example, the copper-bearing schists of the Miami district in Arizona, is rendered most difficult by what is known as a caving " of the sides of the drill holes. As this caving is very greatly increased by the action of flowing water, it occurred to me, after experiencing a great deal of difficulty with caving in diamond-drill holes which I was drilling for the Miami Copper Co., that if I could substitute air for water, much of the caving—with resultant difficulties, such as decreased speed of sinking and increased consumption of diamonds—would be overcome. After some experimenting, I found that it was perfectly practicable to substitute air for the water; forcing the air down the hollow rotating rods in the same manner as is done with water, the air passing out around the bit, which is thus cooled, and ascending on the out~ide of the rods to the collar of the hole, carrying the borings in just as satisfactory a manner as had been done by the water, but without the accompanying destruction or caving of the sides of the drill holes such as had been so generally experienced with the water. When water was encountered in the drilling this water was forced up to the collar just as it would have been had water been used in the drilling, but with the correspondingly decreased flow there was relatively less washing or caving of the sides of the drill holes. The only change necessary in the arrangement of the drill is that a cross instead of a tee is used at the collar of the hole. A tightly woven jute bag is attached to one arm of the cross, for collecting and filtering the sample; and when drilling in dry ground a jet of water is attached to the opposite arm of the cross, to collect the dust and wash down the sample into the bag. The rods rotate through a stuffing box attached to the upper opening of the cross. The distention of the jute bag by the issuing air indicates the operating conditions as sufficiently as did the flow of water when using water in the drill hole. The small percentage of core recovery rendered it necessary to

Jan 1, 1914

By Gregory M. Dexter

Recent litigation in Pennsylvania between three coal-mining companies and a private water company resulted in the payment by the coal companies of the equivalent of about $500,000 to buy a new water supply to replace that which had been damaged by acid drainage from strip mining. An investigation of the relevant facts indicates that the water could have been treated by spending about $40,000 on equipment and $15,000 yearly for chemicals, labor, and power until the contarnination could be reduced about 80 pct. The water company's supply, furthermore, had deteriorated largely by reason of dry weather before stripping was begun by the coal companies. Payment to the water company should not have exceeded $300,000 and could have been as low as $100,000. Strip mining of coal is common in Pennsylvania. The most important objection to it in Pennsylvania is generally acid pollution of runoff water. An outline of the methods, therefore, that could be used to reduce such pollution, to compare acid-contaminated waters. and to treat such waters to make them satisfactory for public and industrial use is worth-while. The watershed of the West Penn Water Co. covers about 4.5 square miles, 20 miles west of Pittsburgh, and has two 90,000,000 gal reservoirs supplying about 1,300,000 gal daily for public and industrial use of which 450,000 gal daily are for two railroads. The pollution arises from weathered derivatives of typical'" Coal Measures"' rocks, the principal source being pyrite (and marcasite) in Pittsburgh and Rooster coals. Springs and seeps on hillsides issue from sandstone and limestone formations intersecting shale or clay land surfaces, or from perched water tables. The two reservoirs create an artificial permanent water table. Soap-hardness tests on three seepage samples taken in a dry summer ranged from 150 to 500 ppm. Water sampled came from aquifers above Pittsburgh and Rooster coals, obviating the possibility of contact with pyrite-containing coal. Since acid contamination of mine waters is the result of chemical reactions of oxygen and water with pyrite, it will be reduced by the exclusion of either air or water. The Sunnyhill Coal Co. has applied this principle in its "contouring" method of strip mining by burying contaminated coal-waste material under a compact, smoothed-up surface of top-soil, gravel, clay, and sand at a cost

Jan 1, 1950

By Alvin Kaufman

At the turn of the century the U.S. had a gross ALVIN KAUFMAN Mineral Economist U.S. Bureau of Mines area slightly in excess of three million square miles, a population of 76 million, a gross national product of $37 billion (constant 1929 dollars) and a mineral production valued at $2 billion (1929 dollars). Some 60 years later its area had increased by 600 thousand square miles, population had risen 140%, gross national product was seven times greater and mineral production had grown to a value five times that of 1900. Of perhaps greater significance, however, were the changes wrought by technology. It was during this period that the "American Way of Life" was revolutionized by the introduction of the airplane and the automobile; man also took his first probing steps in the utilization of nuclear energy and pre- pared to unlock the secrets of space. It was during these six decades, also, that he learned to create additional new materials, some of which were from old sources such as plastics from petroleum and coal. These new materials have created competition and attendant problems for the traditional materials such as iron, copper, lead and zinc. Additional problems undoubtedly will be created by technologic advances in the future.

Jan 2, 1963

One-half fare return rate again available to members of the Institute and dependent members of their families. DON'T FORGET YOUR RAILROAD CERTIFICATE Over 300 members of the A. I. M. E. and dependent mem-bers of their families attending the last annual meeting se-cured return railroad tickets at half price by means of the railroad certificate, thereby saving several thousand dollars. DIRECTIONS 1. Be sure to obtain your railroad certificate when pur-chasing your railroad tickets for the meeting or you will lose money. 2. Purchase your tickets at regular one-way adult tariff fare between the dates specified for your territory in the accom-panying table. 3. Present your certificate for valida-tion at Institute headquarters in New York immediately after registration. Certificates will be validated on Feb. 21 and 22 between 9 a. m. and 5.30 p. in. 4. You must use your return half-rate tickets not later than Feb. 27. 5. Use the same route for both going and return trip. PLEASE REMEMBER THIS 1. Unless-250 certificates are validated at headquarters it will be impossible for anyone to secure the reduced rate. 2. Unless you secure a certificate you cannot take advantage. of the half-rate return fare, even if the necessary 250 certificates are validated.

Jan 2, 1928

By R. H. Barham, G. W. Nabor

Linear aquifers, either limited or essentially infinite, may be encountered in reservoir engineering practice. In areas where faulting fixes reservoir boundaries, the fault block reservoir may have an aquifer of limited extent whose geometry is best approximated as linear. An infinite linear aquifer can occur as a regional feature whenever water movement through the aquifer member is constrained to one direction. Such constraints can arise from major faults, facies changes or pinchout of the member. Miller* pointed out that linear aquifers have received only meager attention in the past. He analyzed the performance of finite and infinite aquifers, developed working equations and curves, and presented examples. While Miller's curves may be used fairly easily, a separate one is required for each size of aquifer. In this paper, Miller's equations have been used as a starting point. By modifying them slightly, they can be reduced to a form which yields a single working curve, applicable to any size of aquifer. Thus. interpolation between curves is eliminated and accuracy is improved. Miller's results for finite aquifers covered only the boundary condition of no flow across the outer aquifer boundary. This paper also includes the case of constant pressure at the outer aquifer boundary.

Jan 1, 1965

By J. C. Savins, G. C. Wallick, W. R. Foster

The dual differentiation-integration method of rbeological analysis is applied to Couette flow. Using machine processing techniques, a spectrum of characteristic derivative functions for a variety of ideal Generalized Newtonian and viscoplastic models has been developed; As for the case of Poiseuille flow the functions for Generalized Newtonian models as a class are strikingly different from the corresponding functions for the class of viscoplastic models. It is shown that this dual scheme of analysis is a highly sensitive analytic method for dotermining the applicable range if a rbeoloaical model. The unique characteristics of this function in the case of viscoplastics may lead to a more precise detection and evaluation of the yield point or yield stress in these materials. INTRODUCTION It has been shown 1,2 that the dual differentiation-integration method of analysis is a discriminating and flexible method for interpreting flow behavior and determining the applicable range of a particular model from Poiseuille flow experiments. In the preceding paper3 the basic equations governing the Couette flow experiment were reviewed and the significance of changes in boundary conditions on data analysis in the case of the viscoplaaic discussed. In this paper the dual method of analysis is applied to Couette flow using the suites of rheological models considered previously.

By Robert H. Merrill, Raymond M. Stateham

Recently, the Denver Mining Research Center of the U.S. Bureau of Mines began tests to detect hazardous or potentially hazardous conditions in or around mines with infrared measurement devices. Among the many potential uses of infrared detection techniques are the location of misfires, underground mine fires, combustion in waste dumps, underground water courses and loose rock. However, the primary emphasis has been placed upon the detection of loose rock in roofs, pillars and faces in underground mines. The rock along the edge of an underground opening is subject to two temperature environments: the temperature of the air in the opening, and the temperature of the rock surrounding the opening. Assuming that the rock on the edge of the opening is solid, the rock will reach an equilibrium temperature that depends upon the temperature and flow of the air, the thermal conductivity of the rock and its ambient temperature. Presume that a loose rock exists among this solid rock; because there is a temperature barrier, to some extent, between the loose and the solid, the loose rock will be affected more than the solid rock by the temperature of the air. Therefore, depending upon the temperature differences between the rock and the air, the loose will be warmer or cooler than the solid.

Jan 1, 1970

By J. M. W. Mackenzie

The rheological properties of aqueous solutions of several commercial flocculants were investigated using a rotating coaxial cylinder viscometer. Similarities between the pH-apparent viscosity relationship and the flocculating properties of the reagents are discussed here. Synthetic neutral polymers and polyelectrolytes are used extensively as flocculants in mining and chemical engineering operations. The action of these reagents has been interpreted as adsorption of the polymer flocculant to the mineral surface, followed by the formation of physical polymer bridges between the particles.4,5 A consequence of the bridging model is that the efficiency of a polymer flocculant depends on the degree with which the polymer is adsorbed to the mineral surface, and the extent to which the polymer molecule forms a bridge between colliding particles. The length of the polymer molecule and its orientation at the mineral surface are important in the bridging mechanism since the further the polymer segments can protrude from the mineral surface the greater the probability may be of these segments contacting another mineral particle. Linke and Booth7 have shown that, for a silica suspension, both the settling rate at a given polymer addition and the maximum settling rate obtainable increase with increasing molecular weight. The analysis of silberbergl0 has

Jan 1, 1964

By Edward Sayre

IN shaft sinking for coal mines, the cost item greatly influences the method adopted. This holds true especially when soft material must be traversed. The average life of a coal mine is short. This is clue either to the limited area of the coal basin or to the great expense of maintenance and haulage underground when the entries are extended a considerable distance from the hoisting shaft. Therefore, the engineer in opening a coal mine is confronted with the fact that the cost must be kept within certain bounds else the venture will prove unprofitable. For this reason he may be prohibited from adopting certain safe, but expensive, methods that are used in sinking caissons for foundations, driving transportation tunnels, or other work of permanent construction. A common method of sinking through difficult ground employs the aid of a steel shoe pushed ahead of the shaft timbers. Another is the drop-shaft method. These two methods were used in sinking the main shaft and the air shaft of the Eagle No. 3 mine, at Des Moines, Ia., and the following data show the relative success and cost of the two methods of sinking under the same conditions. A drill log of the material to be penetrated was as follows (see Plate 1, Fig. .1)

Jan 9, 1916

By N. R. Tipman, G. E. Agar, L. Paré

The flotation chemistry of the commercial INCO matte separation process was investigated. The slow cooling of Bessemer converter matte forms discrete phases of Cu2S and Ni3S2 and a Cu-Ni alloy. After magnetically removing the alloy, the Cu2S and Ni3S2 are separated by flotation at pH 12.4 (saturated lime) using diphenyl guanidine (DPG) as both collector and frother. DPG has been used exclusively in this flotation process because of its unusual selectivity for copper minerals. The surface product resulting from chemisorption of DPG onto theCu2S was identified as the double salt CU(DPG)2SO4.CU(DPG)2(OH)2. The adsorption followed Langmuir behaviour up to a monolayer coverage. In the absence of DPG, the rapid adsorption of oxygen by Cu2S in flotation pulps was observed. The surface product was identified as the insoluble basic copper sulfate CuS04.3Cu(0H)2 with the production of sulfate ion. In the presence of DPG, the oxidation reaction appears to be suppressed. The frothing properties of DPG and commercial frothers were compared. DPG is not a powerful frother. Batch flotation tests confirmed that DPG is a highly selective collector when compared to most sulfhydryl collectors.

Jan 1, 1976

By Frank C. Appleyard

The two calcium sulfate minerals-gypsum and anhydrite-occur in many parts of the world, and gypsum has long been of economic importance in the family of industrial minerals. Gypsum, the dihydrate form of calcium sulfate (CaS042H20) and anhydrite, the anhydrous form (CaSO4) are frequently found in close association, and it is seldom that a calcium sulfate deposit will consist exclusively of one mineral or the other. Although known gypsum deposits are extensive, anhydrite makes up the largest part of total calcium sulfate reserves. However, it has very minor economic use, and most of the following discussion will be devoted to gypsum. Calcium sulfate is one of the principal con- stituents of evaporite deposits, and when pure, has the following composition: [ ] Deposits of pure gypsum or of pure anhydrite which are large enough to be considered commercial have never been found because of both the metastable relationship between the two minerals, and the presence of impurities such as calcium or magnesium carbonates, chlorides, other sulfate minerals, clay minerals, or silica. As a result most mine production of gypsum will range between 85 and 95% pure. Often it is used as mined, although in certain cases, one or more forms of mineral beneficiation are employed to upgrade the product.

Jan 1, 1975