Search Documents

By G. W. Preckshot, N. G. DeLisle, C. E. Cottrell, D. L. Katz

MOST crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank. The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir.

Jan 1, 1942

By M. H. Brady, J. G. Roscoe

Continental No. 1 This mine in Lisbon Valley has an orebody about 1200 ft long and varying from 250 to 70 ft wide. Average width is about 100 ft and stope heights average about 9 ft. It was developed by a 350-ft, 11º inclined shaft for trackless haulage, although a hoist and track are installed for auxiliary hoisting. Mining has been done from horizontal open stopes with random pillar support, using a HD5 tractor for mucking and a 4-wheel drive Gettman shuttle car for tramming. Slushers have been used to some extent in thin ore zones. Back support for stopes and haulage ways has been accomplished by rock bolts and landing mat. The most interesting feature of this mine has been pillar extraction. Mining was done under contract during the first year of operations with little regard for an orderly plan of stope layout or regularity of openings. Most of this work was done in the largest area of the orebody; consequently, pillar recovery has been accomplished under conditions which are far from ideal. However, a workable system has been developed which is competitive, both in cost and production rate, with open stoping.

Jan 7, 1958

By R. S. Dean

MANY studies have been made of the properties of steel produced by adding varying amounts of sponge iron to the charges used in steel-making furnaces.1-3 The results of these previous studies, however, have failed to disclose a reason for the belief of steelmakers that steel made in this way is definitely different from steel made entirely from scrap or iron melting stock. This paper deals chiefly with the structure of the sponge iron, of the wrought iron made by welding the sponge iron into blooms, and of the steel made by melting the forged and rolled blooms. It is believed that the structure of the final steel is inherited from the ore and that this inherited structure produces marked differences in the properties of the steel and explains the feeling of steelmakers which is based on their experience. Three kinds of sponge iron were used in this investigation: One made from a limonite ore reduced with natural gas, one made from a hematite ore reduced with natural gas, and one made from a magnetite ore reduced with charcoal. The sponge iron made by reduction with natural gas

Jan 1, 1935

By F. Weinberg

Measurements have been made of solute segregation during dendrilic growth by using radioactive solute elements and ,measuring the activity of den(12-ites cut from decanted specimens. This has been done for both lead awl tin based binary alloys contaitzing the following solute additions: Ag, T1204, was dependet on ko, the equilibrium distribution coefficient in the following way Fay k &apos;c 0.1, C/C 0.6; for k0 >0.1. 0.6 <c,/c,< I. Qualitative obse?-vations were madc of dendritic segregation, by using autoradiographic techniques, for the Sn + Ag110 and Sn + Tlo4 systems. The observation were found to he in general agreement with the measurements ofCA/Co. Autoradiographic were also obtained of scctiolccl delzr11-iie stalks. These indicated that the stalks had a substructure, dclileated by solute corzetlt?atio?zs nlolg the substructure walls. A new dendrite growth direction <JI2> is reported for tila. SOLUTE segregation in dilute binary alloys has been investigated by Pfann,&apos; Smith, Tiller, and Rut-ter,&apos; and others. They considered the case of a slowly advancing plane solid interface, and derived expressions for the distribution of solute in both solid and liquid during solidification. To determine these expressions, they assumed no diffusion in the solid and either complete mixing in the liquid:&apos; or diffusion controlled solute movements in the liquid without any convective mixing.&apos; The present investigation considers solute segregation during dendritic growth, in which case the solid-liquid interface is not plane, and the growth rates are rapid. Segregation under these growth conditions has not been treated mathematically, because of the relative complexity of the system. It has been suggested by Chalmer, on the basis of preliminary results, that an alternative to the diffusion and heat flow controlled conditions during growth is &apos;diffusionless" dendritic growth in which solid is formed with the same composition as the liquid. He suggests this type of growth may depend upon a solvent-solute relationship that permits some solid solubility without excessive increase in internal energy, as is the case for solutions of tin in lead. On the other hand, Montariol,4 and others, have shown experimentally that some segregation does occur during dendritic growth in metals using etching and radioactive tracer techniques to indicate the concentrations of the solute. The present investigation was undertaken to determine, both qualitatively and quantitatively, the extent of solute segregation associated with dendritic growth in a series of binary alloys, as a function of solute concentration. PROCEDURE The solvent materials used were Vulcan Electrolytic tin (99.997 pct purity) and Tadanac lead (99.998 pct purity). The solute materials were Zn, Sn, and Sb (better than 99.998 pct purity), Ag and Co (99.5 pct purity), and T1 (Fisher "purified" metal sticks). Activation of the solute metals was carried out in the reactor at Chalk River, Canada. Master alloys were prepared by induction heating from the radioactive solute metal and the pure solvent, under argon, in graphite crucibles. Pieces of these alloys were then added to the solvent to give the required solute concentration. Dendrites were grown in essentially the same manner as that described by Weinberg and Chalmer, , in which controlled orientation single crystals were grown dendritically in horizontal graphite boats, and the liquid decanted. The crystals were grown and decanted in an atmosphere of tank argon. Before decanting, a sample of the liquid was drawn up in a glass tube and allowed to solidify rapidly. The orientations of the single crystals were such that <loo> was parallel to the growth direction, and (100) in the horizontal plane for lead, and [1101 and (110) respectively for tin. With these orientations long dendrite stalks formed along the bottom of the boat in the dendrite direction (<100> for lead and [I101 for tin) from which secondary branches grew. Only these secondary branches, which grew freely in the liquid from the dendrite stalk to the liquid surface, were used in the measurements. Accordingly, effects due to substrates and oxides on the surface of the liquid need not be considered. In order to measure the solute concentration C, of the dendrites, individual dendrite stalks were cut from the decanted specimens, remelted, and formed

Jan 1, 1962

By L. G. Huntley

THE only oil produced in Colombia during the past year has been that from the Tropical Oil Co. concession, operated by the International Petroleum Co. This has been about the same in amount as that of 1923, or approximately half a-million barrels gross, which has been used to supply the domestic requirements of the republic and for the company&apos;s own use, in about equal proportions. The Tropical Oil Co.&apos;s field at Infantas has 17 producing wells, for the most part shut in. The company claims an average initial production of about 1000 bbl. each for these wells, which would represent a total potential production of 10,000 bbl. However, the area already outlined by this work is considerable, as drilling has apparently been carried on with the idea in mind of blocking out the field, rather than developing the greatest possible production. Therefore, whether or not the pipeline of the Andian National Corpn. is being built to take care of the amount of crude production admitted by the Tropical Oil Co., or a greater prospective amount, it is certain that this production could be quickly increased if desired.

Jan 3, 1925

By L. G. Huntley

THE only oil produced in Colombia during the past year has been that from the Tropical Oil Co. concession, operated by the International Petroleum Co. This has been about the same in amount as that of 1923, or approximately half a million barrels gross, which has been used to supply the domestic requirements of the republic and for the company&apos;s own use, in about equal proportions. The Tropical Oil Co.&apos;s field at Infantas has 17 producing wells, for the most part shut in. The company claims an average initial production of about 1000 bbl. each for these wells, which would represent a total potential production of 10,000 bbl. However, the area already outlined by this work is considerable, as drilling has apparently been carried on with the idea in mind of blocking out the field, rather than developing the greatest possible production. Therefore, whether or not the pipeline of the Andian National Corpn. is being built to take care of the amount of crude production admitted by the Tropical Oil Co., or a greater prospective amount, it is certain that this production could be quickly increased if desired.

Jan 3, 1925

By J. D. Vincent

During the history of man, the term concentration has had many meanings. Early in history, it may have been construed to mean sorting and smelting. Not many years ago, its definition included only the physical beneficiation processes. Today, and in this article, the term concentration is taking on the meaning of beneficiation and chemical processing, or either separately. An alternate definition could be: concentration is the process of recovering and upgrading an element or nonmetallic mineral so that the product can be used or refined for the needs of man. For the purpose of this article, concentration will have the same connotation as it does in the mineral industry, which has come to include processing methods such as leaching and chlorinization under this heading. Usually, smelting techniques and electrorefining are excluded and classified under the heading of refining. Using the broad definition of concentration, the areas of mining processing include not only the physical beneficiation processes and flotation but also hydrometallurgy and vapor-metallurgy. These methods include sorting, sizing, crushing and grinding, gravity concentrating, magnetic processing and flotation as well as hydrometallurgy and vapor- metallurgical processing.

Jan 1, 1971

By A. Berthet

In the past two decades, of the successive steps leading from iron ore to finished steel, the production of liquid steel and its preparation for the casting operation has probably undergone the most drastic evolution. The reason for this is the development of oxygen converters (top blown and later on bottom blown) and UHP arc furnaces which are replacing the conventional processes such as the open hearth and basic Bessemer processes. These new processes have been great advances, but it would certainly be quite hazardous to assert that the situation will remain the same for the coming decades. In fact, with the advent of continuous steelmaking a new generation of processes has now arrived. The research and development programme at IRSID on continuous an a steelmaking began ten years ago has progressed systematically in the following stages : First a comparison was made on a small pilot scale of various techniques : for example, refining in a runner by top or bottom blowing, pulverizing the metal stream by oxygen, using the mixing effect of a vortex, etc. but for various reasons these processes proved unsatisfactory and were abandoned in favour of a method using the so -called "emulsion refining".

Jan 1, 1972

By G. S. Hume

Three provinces in Canada—New Brunswick, Ontario and Alberta— produce oil and gas in commercial quantities. In addition a small amount of oil is being produced and refined in the Northwest Territories at Norman on the Mackenzie River. The production at Norman is derived from two wells drilled by Northwest (Imperial Oil) Co. in 1920 and 1923. The refined products of the oil are used locally in connection with mineral developments on Great Bear Lake. The production of petroleum by provinces and the consumption of natural gas are shown in Table 3. In addition a small amount of natural gas is produced in the southwestern part of Manitoba from shallow wells for local use. Tables 1 and 2 give detailed information. The greatest drilling activity in 1933 in Canada centered around the southern end of the Turner Valley field, Alberta. In addition to several wells previously commenced in this area, eleven new wells were begun. There were three completions to the Paleozoic producing zone in 1933 in the southern part of Turner Valley and one well was abandoned as a result of being off the favorable structure. Of two wells completed in

Jan 1, 1934

By Walter Morley

This paper is a record of the first of a series of tests on sulfide minerals to be made by the metallurgical department f the University of California. The purpose of the tests here recorded is to determine the action of standard oils, oil mixtures, and addition agents on the flotation of pyrites. The question of the commercial value of pyrite was not considered. Of the many factors affecting flotation, only two-the oil and the other agent used-were made variable. The flotation agents used are given in the accompanying table. PENSACOLA TAR AND TURPENTINE CO. (PENTARCO) NON-POL., SP. Dis. REF. PER No. KIND GR. POINTS INDEX ?VISC. CENT. 200 Refined wood creosote oil 0.965 105-275 1.5096 1.7 7-8 350 Crude pine wood oil 1.019 70-345 1.525 2.9 4 75 Crude wood turpentine 0.887 65-217 1.456 0.9 10-12 80 Crude pine oil 0.911 70-232 1.4894 1.1 8 750 Heavy pine tar oil 1.063 165-350 1.557 41.0 400 Wood creosote oil 1.025 190-360 1.4977 2.9

Jan 7, 1921

By Calvin Pierson, R. S. Dean, E. P. Barrett

MANY studies have been made of the properties of steel produced by adding varying amounts of sponge iron to the charges used in steelmaking furnaces.1-3 The results of these previous studies, however, have failed to disclose a reason for the belief of steelmakers that steel made in this way is definitely different from steel made entirely from scrap or iron melting stock. This paper deals chiefly with the structure of the sponge iron, of the wrought iron made by welding the sponge iron into blooms, and of the steel made by melting the forged and rolled blooms. It is believed that the structure of the final steel is inherited from the ore and that this inherited structure produces marked differences in the properties of the steel and explains the feeling of steelmakers which is based on their experience. Three kinds of sponge iron were used in this investigation: One made from a limonite ore reduced with natural gas, one made from a hematite ore reduced with natural gas, and one made from a magnetite ore reduced with charcoal. The sponge iron made by reduction with natural gas

Jan 1, 1935

By A. N. Roberts, N. W. Stump

New developments in on-stream analysis using immersed radioisotope gages including results from plant installations are described. The control of grinding and flotation using a small digital computer has been complemented by this development. A control scheme for grinding, which is based on maximum throughput at constant product size, and preliminary work in flotation control are also outlined.

Jan 1, 1975

By C. H. Lee, R. Maddin

The diffusion rates of Ag110 in cylindrical single crystals of 99.99 pct pure silver, which were twisted to a total surface strain of 0.91 during the diffusion anneal at temperatures of 700°, 750°, and 800°C, were measured by sectioning and counting as a function of the strain rates. The ratio of the diffusivities while strain ing occurred (Ds) to those of the unstrained specimens varies linearly with the rate of twisting and attains values of near 100 for some of the rates used. The enhancement of diffusion by straining is inversely proportional to the temperature at which diffusion occurs. The activation energy for diffusion determined from the data plotted as a function of the rate of twisting decreases from 44,090 cal per mole for zero strain, to an asymptotic value of 21,000 cal per mole for the strain rates of 22 x it)"5 see-l. Qualitative explanation for the observations based on the generation of nonequilibrium number of defects by plastic deformation will be discussed. The initial research of Buffington and cohen1 on self-diffusion in a iron under compressive stresses contributed the first quantitative information concerning the effect of applied stresses on diffusion. These results were obtained from radioactive Fe55 plated on one of the horizontal surfaces and compressing the large-grained specimens while the diffusion-anneal was occurring. Enhancement of diffusion of a maximum of seventeen times was observed provided the strain was in the tertiary stage of creep and the rates of straining were at least as fast as rates used in the normal creep test. On the other hand, Darby, Tomizuka, and Balluffi,2 extending silver single crystals up to 30 pct elongation at rates of straining about equal to those used by Buffington and Cohen observed no effect. For the past two and a half years at the University of Pennsylvania, we have been investigating the effect or torsional strains on self-diffusion in silver single crystals. If enhancement is observed as has been reported1 a possible explanation may be based upon the generation of fairly large numbers of point defects and their role in the diffusion process. Hence, since torsion should produce an abundance3 of point defects, an increase in the diffusivity while the crystal is being twisted should easily be measured. EXPERIMENTAL PROCEDURE Our research uses single crystals of silver prepared from 99.99 Ag by the Bridgman method in a dynamic vacuum of less than 25 µ. As grown, they are about 25 cm long by 1.3 cm in diam. The crystals are cut into 7.5 cm lengths with a jeweler&apos;s saw and machined to the shape shown in Fig. 1. The test length of the crystal is machined to a 0.6 cm diam after which the ends are masked and the test section etched heavily in HNO3, and KCN:(NH4),S2Os , solution to remove the effects of machining. The specimen is then annealed in vacuum for 8 to 12 hr at 800°C to remove any residual stresses and also to recrystallize the end sections. The recrystallized ends are necessary since experiments showed that single-crystalline end sections are too soft to transmit the desired torque. Occasionally, recrystalliza-

Jan 1, 1960

By J. C. Swartz

New measurements of graphite and cementite solubilities in ferrite have been obtained to resolve disagreements among previous data. To measure graphite solubility, specimens of iron were equilibrated with rarious carburizing atmospheres at temperatures be-twee~z 480" and 1435°C. The carbon activity of each atmosphere relative to graphite was taken from published data. After quenching from each equilibration treatment the concentration of carbon (typically 10 pprn by wt) was determined from the height of the Snoek peak in the internal friction spectrum. A few inclividual analyses by combustion support the reszdts of Smith on the solubility of graphite near the eutectoid temperature. Combination of these combustion and internal friction analyses determines In a, (at 0.01 wt pct) = 24,000/RT - 12.72, where a, is the activtity relative to graphite in ferrite at fixed cornposition. The same specimens were used to determine the solubility of self-stressed cementite precipitates. The results indicate solubilities of 6.3, 23.2, and 68 pprn carbon by wt at respectively 400°, 500". and 600°C. The once large discrepancy between the cementite solubility determined by internal frictiori and that calculated from flee energy data has been almost completely resolved. A recent study1 (hereafter designated I) on the solubility of cementite in a iron did not fully resolve the disagreement among previous data. The remaining disagreement is illustrated by the phase diagram in Fig. L The data of I are represented by the line labeled "stress-free" cementite. They determine a heat of solution of cementite of (14.8 * 0.2) kcal per mole which contrasts with the (20 * 1) kcal per mole derived from Smith&apos;s graphite solubility2 and the formation energy of cementite.3 Toward resolving this disagreement we have obtained new data on the solubilities of graphite and cementite. METHODS As in I the Snoek peak in the internal friction spectrum was used to measure the concentration of carbon dissolved in ferrite. This method relies on the relation C=kQ-1 [1] in which C is the concentration of dissolved carbon, Q-I is the Snoek peak height, and k is a proportionality factor which is a function of the peak temperature, polycrystalline texture, and other parameters characteristic of the ferrite lattice. To determine true heats of solution via Eq. [1], it is necessary to establish that k is independent of the temperature from which the specimen is quenched. Some evidence on this point is contained in a separate report.* Additional evidence is shown by the data points in Fig. 1. These represent the Snoek peaks of two specimens carburized to about 10 ppm C, copper plated, and quenched first from 888º then from 588°C. The copper plate was removed before each Snoek peak measurement. These data show that there is no detectable dependence of k on quenching temperature. The solubility of graphite was determined by repeatedly carburizing various specimens of iron wire with gas mixtures of known carbon activity relative to graphite. To cover a wide temperature range within the a phase boundaries it is desirable to use as low a carbon concentration as is compatible with reasonable precision. With the present internal friction apparatus the best compromise of these desires is a concentration near 10 wt ppm. The dashed line in Fig. 1 was used to approximate the activity of carbon* for

Jan 1, 1970

By R. M. Hudson

The removal of nitrogen from a nitrogenized low-carbon sheet steel that contained 0.011 wt pct N was determined during heat treatment in Hz-N, mixtures. TIze process followed a first-order rate law; that is, plots of the logarithm of nitrogen content in steel were linear with the time of treatment at a given temperature. The rate of removal increased with an increase in temperature from 900" to 1300°F. By 1400°F the rate in dry hydrogen had decreased to a value intermediate between the rates at 1200" and at 1300°F; in wet (2.47 vol pct water vapor) hydrogen the rate at 1400°F was less than the rate at 1300°F and nearly the same as the rate at 1200OF. The rate at a given temperature increased as the 3/2 power of hydrogen concentration in the atmosphere. While wet atmosplzeres were generally more effective than the corresponding dry atmosplzeres, the effect of water vapor was much less pronounced than the influence of hydrogen content. NITROGEN is the principal agent in the strain aging of ferrite, the effect of carbon being secondary.&apos; To eliminate the return of the yield point after straining and aging, it is claimed2 that the amount of nitrogen in solution in steel must be reduced to 0.0002 wt pct. Strong nitride-forming elements (titanium, vanadium, zirconium, and aluminum) can act to eliminate strain aging by combining with nitrogen. It is extremely difficult to decrease the nitrogen content in commercial steels to the low level required by conventional coil annealing because of the poor contact between the strip surface and the reactive atmosphere. However, a variety of gas-metal reactions can be effected by use of the open-coil annealing method,3 in which the metal surface is fully exposed to the atmosphere. With this possibility in mind, the Applied Research Laboratory has studied the influence of time, temperature, and atmosphere composition on the removal of nitrogen from low-carbon sheet steel. MATERIALS AND EXPERIMENTAL WORK Samples from a commercial nitrogenized low-carbon steel (0.010 in. thick) in the cold-reduced condition were used. The chemical composition of this steel is given in Table I. The gas mixtures used are listed in Table 11. The moisture content in the "wet" annealing atmospheres was controlled at a +70°F dew point (2.47 vol pct water vapor) by passing the gas mixture through a glass tube packed with a solid mixture of 10 pct anhydrous oxalic acid and 90 pct oxalic acid dihydrate held at 127°F; this technique has been described previously.4 For "dry" atmospheres, the gas mixtures were passed through a cold trap immersed in liquid nitrogen. A hinged-top Hevi-Duty electric furnace was used with a Vycor-glass furnace tube. When the furnace was at the desired temperature, the gas mixture was passed through the furnace at a flow rate between 1.1 and 1.2 cfh; coupons (size 3 by 3/4 in.) of the steel were pulled into the center of the Vycor-glass

Jan 1, 1964

By W. E. Anderson, T. M. Brady

As part of a larger study to identify factors influencing the practical operating life of wire rope used on large draglines in surface coal mining, field trips to operating surface coal mines were made during late 1975. Wire rope performance information was obtained from personnel at 13 mine sites west of the Appalachians. Seventeen pieces of equipment, utilizing bucket sizes ranging from 30 to 220 cu yd (23 to 168 m), were documented. Draglines at large US surface coal mines can be represented as 120 machines having 60-cu yd (46-m3) buckets, moving 1.8 X 109 cu yd (1.4 x 109 m3) of overburden during 6650 hours of productive availability per year. Based on the limited field study, the calculated downtime resulting from rope-related causes averages 105.6 hours per year for each typical 60-cu yd (43-m3) dragline. The total loss in production from this source alone is thereby estimated at about 25 x 106 cu yd (19 x 106 m3) annually. Although study findings did not reveal anything about dragline rope life that wasn&apos;t known or practiced by one operator or another, most operators can expect improved rope life by periodic review of their practices and by adopting one or more life-improvement measures employed at other sites. Since rope productivity was found to vary by a factor of five among the sites studied, considerable improved average performance is possible. As little as 10% overall improvement would increase national productivity by 2 million cu yd (1.5 X 106 m3) of solid overburden removal. Associated savings in rope costs would be some $2 million annually, plus a large reduction of labor-related expenses. This report outlines preliminary findings which may prove useful to many operators in extending wire rope life. Some of these modifications or adjustments in maintenance/operating practices would not require capital investment. During the field survey, no company was found which had tried cost reductions by using presocketed dump ropes, or dump rope sheaves that opened like a snatch block, so these are suggested as possible improvements requiring modest capital input. Data Acquisition During the field visits, mine operators provided rope life information about their machines. Some of the rope life data consisted of gross averages; other data was in the form of detailed records, including rope construction and manufacturer, cutoff and resocketing periods, end-for-end switching, and downtime for rope change-out. Trends of average hoist rope life and average drag rope life determined from the field study are shown in [Fig. 1] as a function of bucket size. The three lines on the graph have slopes of 1, M, and 1/4. A comparison of the data shows that hoist ropes moved about twice as much material as drag ropes prior to retirement, although more than a two-to-one scatter within each category is evident. As expected, the larger machines with the larger buckets moved more total volume of material. The four pairs of solid symbols represent those data for which detailed rope life histories are presented in subsequent figures.

Jan 1, 1980

By F. H. Wilson, E. W. Palmer

The solid solubility of iron in 2 to 10 pct cupro-nickels increases with temperature and nickel content. Property changes accompanying various heat treatments indicate typical precipitation hardening behavior. Iron content also affects softening temperature and sub-scale formation. These factors, as well as impingement corrosion resistance, influence the optimum iron content of commercial alloys. FOR many years Cu-Ni alloys have been used extensively in the form of tubes, pipes, and plates for the construction of salt-water lines and surface condensers on shipboard and in tidewater power stations. The 30 pct Ni alloy has been considered more resistant to rapidly flowing sea water than alloys of lower nickel content, and has been standard on ships of the U. S. Navy. Some ten years ago, the still better corrosion resistance obtained by modifying the 30 pct Ni alloy with approximately 0.5 pct Fe was recognized, and the iron-bearing alloy rapidly superseded the plain alloy as the standard material for severe service. In 1945, Tracy and Hungerford1 published a study of the effect of iron on the corrosion of various cupro-nickels in sea-salt solutions, and their data indicated that the 10 pct Ni alloy containing about 0.75 pct Fe was equivalent to the 30 pct Ni alloy containing 0.5 pct Fe. This was confirmed by LaQue in discussion of the above paper, and by results in an experimental condenser set up at the Kure Beach marine test station of The International Nickel Co., reported by Freeman and Tracy.&apos; The 10 pct Ni iron-bearing alloy is now being very widely used in applications where the 30 pct Ni iron-bearing alloy was formerly considered standard. While this "substitution" has undoubtedly been stimulated by the present extreme shortage of nickel, it must be emphasized that it involves no loss of service performance, and would have occurred anyway in the course of time, for economic reasons. In view of the increasing use of the 10 pct alloy, it seems desirable to make generally available the results of several investigations of Cu-Ni-Fe alloys carried out in the Metallurgical Research Laboratory of The American Brass Co. in recent years. The present paper, deals with the constitution of these alloys in the copper-rich corner of the system, and with the variations in hardness and tensile properties resulting from the heat treatment of alloys containing various amounts of iron. Most of this work is concerned with alloys containing 10 pct Ni. With over about 0.75 pct fe, the 10 pct Ni alloy is suscep- Alloys Several series of cupro-nickel alloys containing iron were used in these investigations. Most of them were prepared in the laboratory, but two samples of commercially fabricated alloys were included. Series A—Nominally 2 and 5 pct Ni, each with 0 to 1.5 pct Fe. Series B—Nominally 10 pct Ni with 0.1 to 0.4 pct Fe. Series C—Nominally 1.0 pct Ni with 0 to 2 pct Fe. Series D—Nominally 10 pct Ni with 3 to 5 pct Fe. Series E—Nominally 10 pct Ni with 1 and 1.5 pct Fe.

Jan 1, 1953

By N. B. Gray, R. V. Culver, W. S. Boundy, N. W. Stump

The kinetics of sulfation of single crystals of lead sulfide to lead sulfate have been studied between 969" and 1073°K in gas atmospheres of known composition using a thermobalance technique. The data are described by an equation derived on the basis that diffusion outward through the Product layer is the major controlling step. The rate of sulfation is linearly related to the logarithm of the sulfur trioxide partial DESPITE its industrial significance the oxidation of lead sulfide has received limited attention. The oxidation reactions have been studied using beds, briquettes, single crystals, or thin films of lead sulfide. Lead oxide and lead sulfate (PbSO,) were formed when Mclntoshl and Gardner2 roasted beds of galena pressure and the temperature coefficient of reaction is 40 ± 5 kcal per g mole. Gold marker experiments show that the sulfate layer grows by outward movement of ions through the sulfate layer. Initially the PbSO, adheres to the PbS but later forms an irnpewious spheroidal envelope; PbS vaporizes and pb2&apos; ions diffuse through the envelope to react at the external surface. in air at temperatures up to 800°C. In a more extensive investigation, Tchizhykov3 obtained Pb, PbO, and PbS04 in accordance with Eqs. [1] to [4], when a bed of -200 mesh galena was oxidized in O2-N2 mixtures at 700° to 900°C.

Jan 1, 1968

LIST OF REFERENCES COMPILED BY ENGINEERING SOCIETIES LIBRARY FUEL POSSIBILITIES IN STEEL MAKING. Iron Age, November 6, 1913, p. 1056-1059. Paper read before the American Iron and Steel Institute, by William Whigham. The author discusses the use of pulverized coal as a fuel for open-hearth furnaces. IMPROVED PULVERIZED FUEL FEED DEVICE. Iron Age, November 6, 1913, p. 1024. Brief description of the Dunn apparatus, especially intended for cement kilns, but used also in the nodulizing of iron ore. WIDER UTILIZATION OF PULVERIZED COAL, H. R. Barnhurst. Iron Age, October 23, 1913, p. 906-908. Part of discussion of paper by James Lord on The Use of Pulverized Fuel in Metallurgical Furnaces, read before the Engineers&apos; Society of Western Pennsylvania. POWDERED COAL FOR OPEN HEARTH FURNACES. Iron Age, October 16, 1913, p. 855. Abstract from the "Coal and Coke Operator." USE OF PULVERIZED COAL AS A FUEL FOR BOILERS, R. C. Carpenter. Sibley Journal of Engineering, December 1913, p. 85. COAL-DUST FIRED BOILER. Indian Engineering, November 29, 1913, p. 301. PROGRESS IN FUEL UTILIZATION. Mining and Scientific Press, October 25, 1913, p. 638. BUFFALO GRAIN-ELEVATOR DUST EXPLOSION. Engineering News, July 31, 1913, p. 223-24. Reprinted in the National Fire Protection Association Quarterly, October, 1913, p. 149-151. Mention is made of the danger of explosions in connection with the burning of powdered coal. POWDERED FUEL AND EXPLOSIONS. Railway Age Gazette, July 18, 1913, p. 53-84. Letter by W. D. Wood. USE OF PULVERIZED COAL IN METALLURGICAL FURNACES, James Lord. Engineers&apos; Society of Western Pennsylvania, Proc., October, 1913, p. 363-371; discussion, p. 371-417. With bibliography.

Jan 3, 1914

By A. B. Wood

In welding and metal working by electricity, two systems are in use,—the so-called. incandescent system, in which the material operated upon is traversed by currents of large volume and low electro-motive force, the current having a continuous metallic circuit during the welding operation, and the arc system, in which the electric arc is utilized. It is the purpose of the present paper to call attention to this last

Jan 1, 1892