Search Documents

By R. A. Irvine

The use of large vibrating screens presents unique challenges to the screen manufacturer, the plant designer, and the plant operator. The design of vibrating structures that span greater unsupported distances is critical to the reliability of a screen subjected to billions of fatigue cycles. Larger percentages of total plant production become dependent upon fewer, larger vibrating screens. Plant designers and operators must plan for equipment maintenance in a manner which optimizes the production availability of large vibrating screens.

Jan 1, 1985

By Joseph W. Leonard

Evidence is presented to show that certain coals can be super-cleaned, using present coal preparation processes, to reduce sulfur below levels that are commonly believed to be possible. The evidence points to the need to develop continuous sorting methods by which coal coming from a mine can be segregated so that different raw coal types can be processed separately to produce a super-clean coal in addition to coals cleaned to more common levels of sulfur. Evidence is presented and techniques discussed that may be applicable for making the method feasible.

Jan 1, 1976

By F. Louis Grammer

The rapid advances on the mechanical side of blast-furnace practice have not always been accompanied by a proper appreciation of the metallurgical requirements. This is illustrated occasionally by the improper use of automatic barrow chargingdevices and bins (introduced at the expense of accuracy in weight), with ores of irregular composition or ores that have been poorly graded. The 100-ft. blast-furnace has not always been advantageous, and in many instances the increase in the number of tuyeres, from 8 or 12 to 20, has resulted in decreased output. The data pertaining to this division of blast-furnace practice are now sufficiently complete to allow inferences to be made. The use of fine ores has indicated the manner in which large outputs could be obtained, as it has emphasized the fact that intimacy of contact. between gases and ore, and coke and air, were more important than the time of exposnre. It was reasonable to suppose that if more points of contact were made between the air and the coke, their union would occur in a shorter period of time, and the coke would be burned more rapidly in the same-sized hearth, and an increased output thereby obtained. In consequence of this theory, many furnace men upon relining a furnace increased the number of tuyeres from 8 or 12 to 20, or even more, frequently with unfortunate results. If the number of tuyeres in an old furnace is

Jan 1, 1904

By Alexander Field

INTRODUCTION THE Bureau of Mines is investigating the problem of slag viscosity, its variation with the temperature and with the composition of the slag, and its effect upon the distribution of the sulphur between molten iron and slag, as introductory to a series of contributions to the theory of the metallurgical processes. The method of measurement, viscosity, apparatus, furnace and other accessories mentioned in this paper have been described fully in a Bureau of Mines report.1 THE LITERATURE ON SLAG VISCOSITY The viscosity of blast-furnace slag had not been measured previous to the investigation described in this report. A number of investigators have determined the "fusibility," or softening temperature, of slags by means of the cone method or, other deformation method, but these methods supply only limited information regarding the temperature-viscosity relations.-of the slag in question. Any deformation method that may be employed indicates only the temperature at which the slag attains a more or less definite viscosity, the magnitude of the value obtained depending on the method used. For details of the various methods used by different investigators, see, the Bureau of Mines paper already referred to. An isolated measurement by Doelter on a single mixture at 1,300° C. represents the highest temperature reached in the various viscosity investigations previous to those described in this report, in which results have been referred to absolute units. Arbitrary deformation tests have of course been made at much higher temperatures.

Jan 2, 1917

By H. N. Lawrie

This study was undertaken on account of the lack of definite knowledge concerning the influence of bismuth on wire-bar copper, and the small elimination of bismuth from copper-matte during the smelting-operations. The early workers who studied the influence of bismuth on copper confined their investigations to malleability and ductility—two physical properties which are related to the others so intimately that their determination is of primary importance. Karsten and Levo1,² using bending- and mealleability-tests, seem to have been the first to take up the subject, and while their results are incomplete, they agree in the main with the later work of Hampe.3 The bending-tests used by the first investigators consisted in bending the specimen until it failed. The malleability-tests were made by beating the material to a knife-edge with a hammer. Hampe not only determined the percentage of bismuth which would cause red-shortness and cold-shortness of the alloy, together with other influences of bismuth on the malleability and ductility of copper, but also took up the influence of the bismuth protoxide, BiO, on copper, and of bismuth sesquioxide, Bi,O,, on the copper protoxide, CuO. Hampe's conclusioris of the influences of these two latter compounds of bismuth on copper are as follows : "If the protoxide of bismnth be alloyed with metallic copper, it is not changed to metallic bismuth, but remains mechanically distributed throughout the copper.

Jan 1, 1910

By Robert J. Willard

The scanning electron microscope (SEM), became commercially available in 1966. Embodying some unique features not provided by conventional electron microscopes, this new electron-optical instrument offers the scientific community a new way of observing the surfaces of materials. In rock mechanics research, the SEM should prove a useful basic tool in characterizing rock fracture on a very small scale and thus contribute to a better understanding of rock behavior at larger scales. This article presents one example of how the SEM is being applied to such research at the Twin Cities Mining Research Center operated by the U.S. Bureau of Mines in Minneapolis. This research center conducts theoretical and experimental studies on a broad range of mechanisms that induce disintegration by the application of energy to rock.1 Some of these studies are concerned with the relation of microstructure to rock behavior and are carried out mainly with the petrographic microscope. At the same time, however, the center recognizes that this relation must be studied through several orders of magnitude, from lattice-size units of rock-forming minerals to field-size rock units. The SEM fits this scheme by extending the capability of the petrographic microscope into smaller orders of magnitude. However, because its resolution is limited to about 200 A at 10,000x, the SEM is not capable of resolving lattice-size units, and hence a conventional electron microscope with a much greater resolution capability is necessary at this order of magnitude.

Jan 6, 1969

By Ben Gumpertz

THE important factors in any study of the screening of sand with a gravel enve-lope, as applied to use in oil wells, are: (r) sand size and shape, (2) gravel size and shape, (3) ratio of gravel size to sand size, (4) flow velocity, (5) viscosity of the fluid. Perhaps the first extensive investigation of the function of gravel in screening sand was performed by Coberly and Wagner,1 from which the following conclusion was drawn: "The diameter of the largest grains in a single classified sand suitable for gravel packing is approximately 23 times the grain size at the ten-percentile analysis of the formation sample." This applies to sands classified by Tyler screens and is for gravel grains of the maximum size that could be used to form a stable bridge. Field practice has shown that the screening effect of a given gravel for a given sand apparently varies with the flow velocity.2 Also, it has been assumed by some opera-tors that the thickness of the walls of the gravel envelope surrounding the well has little effect upon the screening process. It is thought by others that a narrow envelope of gravel might form an ineffec-tive screen. Thus the purposes of this work are: I. To investigate the effect of gravel-sand size ratio upon screening action under the condition of varying flow velocities. 2. To investigate the effect upon screen-ing action of varying the thickness of the gravel screen.

Jan 1, 1940

By W. A. Tiller, W. C. Johnston

A theoretical analysis of alloy solidification in which the effective partition coefficient, k, of the solute is allowed to vary as a function of interface position is performed. A variety of solute distm'butions in the solid is predicted depending upon the functional dependence of k with interface position. Conversely, the variation of k with interface position required to produce a particular solute distributzon in the solid can be calculated. These preciictions have been tested by controlling the width of the momentum boundary layer in the liquid as a function of interface position with a rotating mugnetic field. One of the objects of controlled solidification is to utilize the freezing process for the preparation of crystals of specific materials containing a predetermined distribution of solutes. For example, a thermoelectric power generation material may exhibit a figure of merit, 2,' as a function of temperature, T, and solute concentration, C, as illustrated in Fig. 1. If we wish to use this material in a device between the temperature limits T1 to T2 a significantly greater efficiency will result from the device if the thermoelectric element illustrated in Fig. 1 consists of a range of solute concentrations appropriately located with respect to the temperature distribution rather than using a sample of constant solute concentration. For this reason and many others2 we are interested in programming and controlling the solute distribution in a single crystal

Jan 1, 1962

By Alexander L. Field

The Bureau of Mines is investigating the problem of slag viscosity, its variation with the temperature and with the composition of the slag, and its effect upon the distribution of the sulphur between molten iron and slag, as introductory to a series of contributions to the theory of the metallurgical processes. The method of measurement, viscosity apparatus, furnace and other accessories mentioned in this paper have been described fully in s Bureau of Mines report.1 The Literature on Slag Viscosity The viscosity of blast-furnace slag had not been measured previous to the investigation described in this report. A number of investigators have determined the "fusibility," or softening temperature, of slags by means of the cone method .or other deformation method, but these methods supply only limited information regarding the temperature-viscosity relations of the slag in question. Any deformation method that may be employed indicates only the temperature at which the slag attains a more or less definite viscosity., the magnitude of the value obtained depending on the method used. For details of the various methods used by different investigators, see the Bureau of Mines paper already referred to. An isolated measurement by Doelter on a single mixture at 1,300" C. represents the highest temperature reached in the various viscosity investigations previous to those described in this report, in which results have been referred to absolute units. Arbitrary deformation tests have of course been made at much higher temperatures.

Jan 1, 1917

By G. T. Murray

The aging behavior of a Cu-Ti (3.2 at. pct Ti) alloy has been followed by electrical resistivity, hardness, and metallographic changes. The resistivity data indicate two principal processes, the first causing a sharp decrease in resistivity, and the second, which occurs over a long period of time, a much smaller rate of decrease. Lamellar nodules, Widmanstätten platelets, and homogeneous continuous precipitation was observed. The Widmanstätten platelets grow at the expense of the latter. When this study was initiated, little information was available on the aging behavior of copper-base titanium alloys. Several articles'-3 that appeared in the early 1930's showed that these alloys could be strengthened by precipitation, but a detailed study was not made. Within the past year, however, two other more comprehensive studies4'5 have been reported in the literature, one consisting primarily of an investigation of mechanical properties, the other

Jan 1, 1961

By P. Crowther, G. J. Lamprecht

The solubilities of silver, zinc, and cerium in liquid sodium, in the temperature ranges 100 to 270°C, 190° to 550°C, and 120" to 460°C, respectively, have been determined. From the solubility data the heat the entropy the partial molal enthalpy of mixing the excess entropy and the partial molal free energy of solution for the systems Nu-Ag and Na-Zn have been calculated. For the system Na-Ce the observed negative is discussed in terms of the solubility of the oxide Ce2O3. In an earlier publication the results obtained in the study of the solubility of tin' in liquid sodium are presented, as well as the detailed analytical procedures used. 1) REAGENTS Spectroscopically pure metals as supplied by Johnson Matthey and Co, were used to produce the following tracers: 253-day Ag110, 245-day zn65, and 325-day ce141. The tracers were prepared by irradiation in a thermal neutron flux of 4 x 10 13 neutrons cm-2 sek-1. To obtain a uniform amount of the required specific activity, needed for each solubility experiment, the radioactive metal was diluted with the corresponding inactive metal, by melting them together in an inert atmosphere. The liquid sodium used contained 11 ±2 ppm of O,1 determined by the vacuum distillation method.' The oxygen was assumed to be present as the oxide NaD. 2) THE SYSTEMS: SODIUM-SILVER AND SODIUM-ZINC Plots were made of the log of the mole fraction of silver, Fig. 1, and of zinc, Fig. 2, dissolved in the liquid sodium vs reciprocal absolute temperature. The equations for the solubilities, based on the least-squares fit to each plot, are: where Xi is the mole fraction metal dissolved in sodium, T is the absolute temperature, and s is the standard deviation in the value of log Xi. The heats and the entropies lution were calculated from the solubility data by In neither of the two cases was any intermetallic compound formed between sodium and the solute metal as was the case for tin.' Thus, for the silver and zinc systems the pure metal was taken as the reference phase. Since the solids in equilibrium with the liquid sodium were the pure metals, one can calculate the partial molal enthalpy of mixing and

Jan 1, 1969

By John L. Lamont, Walter Crafts

ADEQUATE hardenability has long been recognized as one of the first requirements for producing desired mechanical properties in a heat-treated steel. Since the introduction of the Jominy end-quench test1 and the development of correlative information to expand its use, industry has had an effective measure of hardenability. Prediction and control of the hardenability have been made possible by Grossmann's principle2 for calculating hardenability from chemical composition; and Field's conversion3 from depth of half-martensite hardening to Rockwell C hardness has made the relation more quantitative. These developments have facilitated the design of new steels and the control of standard grades to the extent that it has been possible to establish tentative hardenability bands for some of the more commonly used alloy steels.4 As the depth of hardening of the Jominy test specimen is usually measured by Rockwell C hardness, it was considered that it should be possible to predict the hardness by a more direct calculation. It has been found that this can be accomplished by the addition of Rockwell C units proportional to the carbon and alloy content, grain size, and position in the Jominy test specimen. The calculation has been found to be fairly accurate, and because of its additive character is relatively simple to use. In principle the method of calculation is somewhat similar to the expressions developed by Herty, McBride, and Hollenback,5 Burns, Moore, and Archer,6 and Burns and Riegel.7 The calculation is started from a base that includes the effects of carbon content and position in the Jominy test speimen. Rockwell C units are added to the base in proportion to the alloy content and grain size. This sum represents the Rockwell C hardness up to the level at which a disproportionate increase of hardness is caused by the formation of martensite, and above this level an increment for martensite hardening is added. The effects of alloys are directly proportional to the amounts present and are independent of each other, the carbon content, and the position in the specimen. Furthermore, the factors for determining the martensite increment are dependent only on carbon content and are independent of cooling rate and alloy content. It is this absence of interrelation between the different factors that makes it possible to calculate the hardness and makes the method of calculation consistent with the principle that the character of the hardening reaction is governed primarily by carbon and that alloys exert their effect chiefly through control of the critical cooling rate. The principle of the calculation, and the effects of alloys on the critical cooling rate,

Jan 1, 1945

By Walter Craft, John L. Lamont

Adequate hardenability has long been recognized as one of the first requirements for producing desired mechanical properties in a heat-treated steel. Since the introduction of the Jominy end-quench test' and the development of correlative information to expand its use, industry has had an effective measure of hardenability. Prediction and control of the hardenability have been made possible by Grossmann's principle2 for calculating hardenability from chemical composition; and Field's conversiona from depth of half-martensite hardening to Rockwell C hardness has made the relation more quantitative. These developments have facilitated the design of new steels and the control of standard grades to the extent that it has been possible to establish tentative hardenability bands for some of the more commonly used alloy steels.4 As the depth of hardening of the Jominy test specimen is usually measured by Rockwell C hardness, it was considered that it should be possible to predict the hardness by a more direct calculation. It has been found that this can be accomplished by the addition of Rockwell C units proportional to the carbon and alloy content, grain size, and position in the Jominy test specimen. The calculation has been found to be fairly accurate, and because of its additive character is relatively simple to use. In principle the method of calculation is somewhat similar to the expressions developed by Herty, McBride, and Hollen-back,5 Burns, Moore, and Archer,= and Burns and Riege1.l The calculation is started from a base that includes the effects of carbon content and position in the Jominy test speimen. Rockwell C units are added to the base in proportion to the alloy content and grain size. This sum represents the Rockwell C hardness up to the level at which a disproportionate increase of hardness is caused by the formation of martensite, and above this level an increment for martensite hardening is added. The effects of alloys are directly proportional to the amounts present and are independent of each other, the carbon content, and the position in the specimen. Furthermore, the factors for determining the martensite increment are dependcnt only on carbon content and are independent of cooling rate and alloy content. It is this absence of interrelation between the different factors that makes it possible to calculate the hardness and makes the method of calculation consistent with the principle that the character of the hardening reaction is governed primarily by carbon and that alloys exert their effect chiefly through control of the critical cooling rate. The principle of the calculation, and the effects of alloys on the critical cooling rate,

Jan 1, 1947

By John L. Lamont, Walter Craft

Adequate hardenability has long been recognized as one of the first requirements for producing desired mechanical properties in a heat-treated steel. Since the introduction of the Jominy end-quench test' and the development of correlative information to expand its use, industry has had an effective measure of hardenability. Prediction and control of the hardenability have been made possible by Grossmann's principle2 for calculating hardenability from chemical composition; and Field's conversiona from depth of half-martensite hardening to Rockwell C hardness has made the relation more quantitative. These developments have facilitated the design of new steels and the control of standard grades to the extent that it has been possible to establish tentative hardenability bands for some of the more commonly used alloy steels.4 As the depth of hardening of the Jominy test specimen is usually measured by Rockwell C hardness, it was considered that it should be possible to predict the hardness by a more direct calculation. It has been found that this can be accomplished by the addition of Rockwell C units proportional to the carbon and alloy content, grain size, and position in the Jominy test specimen. The calculation has been found to be fairly accurate, and because of its additive character is relatively simple to use. In principle the method of calculation is somewhat similar to the expressions developed by Herty, McBride, and Hollen-back,5 Burns, Moore, and Archer,= and Burns and Riege1.l The calculation is started from a base that includes the effects of carbon content and position in the Jominy test speimen. Rockwell C units are added to the base in proportion to the alloy content and grain size. This sum represents the Rockwell C hardness up to the level at which a disproportionate increase of hardness is caused by the formation of martensite, and above this level an increment for martensite hardening is added. The effects of alloys are directly proportional to the amounts present and are independent of each other, the carbon content, and the position in the specimen. Furthermore, the factors for determining the martensite increment are dependcnt only on carbon content and are independent of cooling rate and alloy content. It is this absence of interrelation between the different factors that makes it possible to calculate the hardness and makes the method of calculation consistent with the principle that the character of the hardening reaction is governed primarily by carbon and that alloys exert their effect chiefly through control of the critical cooling rate. The principle of the calculation, and the effects of alloys on the critical cooling rate,

Jan 1, 1947

By Byron Bird

WHILE Mr. Fahrenwald has been working on the fundamentals of ore-dressing, in Idaho, the Northwest Experiment Station of the U. S. Bureau of Mines, in cooperation with the University of Washington, has been studying the corresponding fundamentals for the closely-allied subject of coal-washing. In this work many of the principles outlined in Mr. Fahrenwald's paper have been touched on, one important exception being that phase of his studies where conditions were approximated between those existing on a table and those existing in a hindered-settling classifier. During the past three years this work has been given over almost exclusively to a study of coal-tabling to devise better methods of cleaning fine sizes of coal, particularly the coals of the Northwest, which are very difficult to wash. One important result of this study thus far has been the development of a satisfactory hindered-settling coal classifier, now in use in several commercial plants. Recently table stratifica-tion has been the subject for study. This latter phase of the work with coal,. as well as the earlier portion dealing with hindered-settling classification, has in a measure paralleled Mr. Fahrenwald's work with ore. Without going into details about the results of the coal experiments, I shall merely say that, from a quali-tative standpoint, they are, in general, concordant with Mr. Fahrenwald's, but that from a quantitative stand-point the results, particularly those with, table strati-fication, are somewhat different. These differences may disappear as the work progresses-Mr. Fahrenwald is further ahead with his experiments than we are at the Northwest Station-but if not, the disparity would not be surprising, and indeed would be what one might reasonably expect when investigators work on two very dissimilar materials and use different apparatus and methods of study. However, this- mention of our coal-washing experiments is made only in passing. A principle of general application that may be estab-lished from Mr. Fahrenwald's paper is that different types of stratification should be used in successive' gravity-concentration processes to. obtain best results.

Jan 3, 1927

By James J. Scott, John J. Reed

In a year fraught with difficulties, especially to small operators, the more stable mining organizations have shown a dynamic readiness to plunge ahead in the development of new mines, new and ingenious equipment and new tools for management to take the guesswork out of important decisions. New Mining Equipment The mining equipment display at the American Mining Congress in San Francisco demonstrated some rather radical new design concepts and a new willingness to use imagination to come up with ingenious new applications and adaptations of standard equipment.

Jan 2, 1963

Jan 2, 1976

By AIME AIME

Council.* PRESIDENT O. THE COUNCIL. JOHN HAYS HAMMOND NEW YORK, N. Y. (Term expires February, 1909.) VICE-PRESIDENTS OF THE COUNCIL. SAMUEL B. CHRISTY BERKELEY, CAL. JOHN A. CHURCH NEW YORK, N. Y. PEPSIFOR FRAZER PHILADELPHIA, PA. (Term expires February, 1909.) J. PARKE CHANNING NEW YORK, N. Y. FREDERICK W. DENTON PAINESDALE, INCH. JOHN B. FARISH DENVER, COLO. (Term expires February, 1910.)

Jan 5, 1908

By David Cole

DAVID COLE, EL PASO, TEXAS (communication to the Secretary*).-I have read with great interest Dr. Gahl's painstaking paper giving us the details of development of flotation at Inspiration, and it seems to me that he has covered the ground so completely that there is little to discuss or criticize in connection with his subject. While it was in operation, the test mill in which the campaign was carried on was the Mecca of mill men and metallurgists. There was much to interest students of milling methods in addition to the flotation experiments, and readers of Dr. Gahl's paper will miss the information they hoped to get when the "pilot" mill results were. finally compiled, and I hope that the following remarks outlining from a distance some of the things that happened there will bring forth the rest of the story of the performances recorded in these important experiments. Prior to the use of flotation methods in concentration it had long been recognized that the "unavoidable" losses of sulphides were in the slime which is inevitably produced in the grinding operations required to free the minerals to be separated. Classifying the feed prior to its final stage of treatment had long been in style in milling. This assisted the sand-handling machines and resulted in lowering the tailings made by them, but at the expense of the slime-handling department; and while little was expected of the latter, the wisdom of complicating the process by hydraulic classification was being seriously questioned. Indeed, at the

Jan 10, 1916

[ ] Utilizing tendencies for low grade ores in the Sudbury District of Ontario to cave after higher grade ore has been mined, International Nickel Co., of Canada, Ltd., is recovering millions of tons of nickel-copper ore once regarded as submarginal. Inco is working lower grade ore than ever mined before from its underground operations because of the caving method and metallurgical practices. In the caving method, blocks containing as much as 1.5 million tons of ore are undercut. As ore from the undercut block is withdrawn, the block to be mined breaks away and starts to disintegrate as it moves downward. Inco is also using the blasthole method, using explosives to break slices of harder, tougher ore from solid material. Inco has built a new concentrator at one of its most recent shafts for handling the increased tonnages of low grade ore. The concentrator presently has a 10,000-ton per day capacity, and is scheduled to be increased to 12,000 tons. Hoisting from the mine is by push-button control and the ore is milled on the spot. A 7 ½ -mile pipeline carries bulk concentrate to reduction plants at Copper Cliff. Giant crushers, weighing 165 tons each, have been installed underground. Twenty-ton electric locomotives haul ore to the crushers. The expansion program is expected to lift total annual production of nickel in the free world to 375 million pounds annually, an increase of 150 million pounds. Inco is presently mining more than 1 million tons of ore per month from combined surface and underground operations.

Jan 1, 1952