Search Documents

By S. E. Maddigan, A. I. Blank

Many experimental and theoretical investigations have been made on the processes involved in annealing and recrystallization of metals. Most of these, however, have treated the time element as constant and heat-treatments used have been for relatively short times. Aside from the early work by Carpenter and Elam,' the few that have investigated the effect of time on the processes have usually done so for fairly short time periods. During recent years the growing interest in long-time creep properties of metals and alloys under stress has made increasingly important a better knowledge of the recrystallization during prolonged heating. The recrystallization temperature of 70-30 brass given by Clark and White" in 1932 was somewhat above 400°F. (204°C.) but under 500" (260°C.), whereas in our laboratory recrystallization has been observed in creep specimens at 204°C., the lowest temperature of Clark and White's range. Since the creep properties are quite different above and below the recrystallization temperature, erroneous conclusions can readily be drawn by the application of short-time recrystallization data to creep problems. It was thus considered of both practical and theoretical value to make long-time annealing studies near the minimum recrystallization temperature. In this way useful additions could be made to data on recrystallization temperatures and, since the reactions in this range are relatively slow, additional insight could be obtained into the factors involved in annealing. Several comprehensive reviews of recrystallization processes have been written,3-6 therefore only a brief review of the generally accepted facts will be given here. Though the effects of heat-treatment usually are expressed as related to observations with varying temperatures, it is logical to assume that the same order of occurrence will exist with time as a variable. Thus, we may postulate that with increasing time we mill observe the following

Jan 1, 1940

By Stuart E. Buckley, C. R. Hocott

The viscosity of the oil in the reservoir is one of the properties that influence its movement through the sand to producing wells. Measurements of viscosity, therefore, are pertinent to problems associated with well behavior and with the estimation of recoveries, and afford an indirect means for partial evaluation of various methods of controlling reservoir behavior. The effect of dissolved gases on the viscosity of crude oil has been determined,ls2 but no data have been published on the viscosity of representative samples of reservoir oils. This paper describes a simple instrument that has been used to determine the viscosities of a number of subsurface oil samples at the temperatures and pressures existing in the reservoirs, and presents the results of the determinations for typical fields. Construction oF the Apparatus The principal requirements of any instrument used for the examination of subsurface samples are that it be strong and simple both in design and in method of operation. Accuracy beyond that of the degree of reproducibility of subsurface Sam-~les from various wells in a reservoir or exceeding that of the common measure-merits of reservoir temperatures and Pressures is not required. Because of the expense of procuring subsurface samples, it is necessary also that the instrument operate on a relatively small fraction of a sample, leaving the remainder for other tests, and that there be few or no failures of the equipment to cause undue delay or loss of a sample. After preliminary experiments with a falling bullet, the results of which were not satisfactory, a simple viscosimeter was built of the rolling ball type first proposed by Flowers3 and later used by several investiga-tor. 5.8 The apparatus consists essentially of a removable, accurately bored cylindrical barrel of 1/4-in. nominal internal diameter, 8 in. long, in which a closely fitting steel ball rolls through the oil with the barrel inclined at a definite angle. The ball makes contact at one end of the barrel with ail insulated electrode, closing an electrical circuit, which actuates a buzzer. The meas-urements consist essentially in determining the time required for the ball to travel the length of the barrel. The details of the construction are shown in Fig. I. The barrel in which the ball rolls was made from a section of 25-caliber blank rifle barrel, specially bored to an exact uniform diameter and polished. The barrel slides snugly into a hole bored in a solid stainless-steel cylinder, an upper external shoulder of the barrel compressing a small spring, and is held in place by a hollow nut. The spring prevents the barrel from seating against the bottom of the bored hole in the cylinder, while narrow external longitudinal slots in the barrel permit fluid to flow around it and through the bottom. The upper part of the recess in the steel cylinder is enlarged to form a tapered chamber, which acts as a reservoir for the oil and affords space for agitation to ensure

Jan 1, 1941

By C. R. Hocott, Stuart E. Buckley

The viscosity of the oil in the reservoir is one of the properties that influence its movement through the sand to producing wells. Measurements of viscosity, therefore, are pertinent to problems associated with well behavior and with the estimation of recoveries, and afford an indirect means for partial evaluation of various methods of controlling reservoir behavior. The effect of dissolved gases on the viscosity of crude oil has been determined,ls2 but no data have been published on the viscosity of representative samples of reservoir oils. This paper describes a simple instrument that has been used to determine the viscosities of a number of subsurface oil samples at the temperatures and pressures existing in the reservoirs, and presents the results of the determinations for typical fields. Construction oF the Apparatus The principal requirements of any instrument used for the examination of subsurface samples are that it be strong and simple both in design and in method of operation. Accuracy beyond that of the degree of reproducibility of subsurface Sam-~les from various wells in a reservoir or exceeding that of the common measure-merits of reservoir temperatures and Pressures is not required. Because of the expense of procuring subsurface samples, it is necessary also that the instrument operate on a relatively small fraction of a sample, leaving the remainder for other tests, and that there be few or no failures of the equipment to cause undue delay or loss of a sample. After preliminary experiments with a falling bullet, the results of which were not satisfactory, a simple viscosimeter was built of the rolling ball type first proposed by Flowers3 and later used by several investiga-tor. 5.8 The apparatus consists essentially of a removable, accurately bored cylindrical barrel of 1/4-in. nominal internal diameter, 8 in. long, in which a closely fitting steel ball rolls through the oil with the barrel inclined at a definite angle. The ball makes contact at one end of the barrel with ail insulated electrode, closing an electrical circuit, which actuates a buzzer. The meas-urements consist essentially in determining the time required for the ball to travel the length of the barrel. The details of the construction are shown in Fig. I. The barrel in which the ball rolls was made from a section of 25-caliber blank rifle barrel, specially bored to an exact uniform diameter and polished. The barrel slides snugly into a hole bored in a solid stainless-steel cylinder, an upper external shoulder of the barrel compressing a small spring, and is held in place by a hollow nut. The spring prevents the barrel from seating against the bottom of the bored hole in the cylinder, while narrow external longitudinal slots in the barrel permit fluid to flow around it and through the bottom. The upper part of the recess in the steel cylinder is enlarged to form a tapered chamber, which acts as a reservoir for the oil and affords space for agitation to ensure

Jan 1, 1941

By W. D. Von Gonten, R. L. Whiting

Regression analysis was used to correlate the physical properties of 478 sandstone and 90 carbonate core samples. Porosity, permeability, electrical formation resistivity factor, capillary pressure and the sonic velocity of the shear and compressional waves were measured. Prediction equations for porosity, permeability and electrical formation resistivity factor were found which should be useful in understanding the relationships between the physical properties of porous media in formation evaluation. INTRODUCTION The physical properties of porous media are important to the petroleum engineer and geologist. To evaluate fully the potential and behavior of a subsurface formation such as a petroleum reservoir, certain physical properties of the porous medium must be known. The problem of accurately determining physical properties of subsurface formations has not been solved because many determinations must be made by indirect measurements and because of the difficulties caused by complex pore structure and presence of clays in most naturally occurring porous media. Due to the difficulty in measuring some of the physical properties of porous media, it would be advantageous to be able to predict a certain physical property of a rock from other physical properties of the rock which could be measured more easily and more accurately. Since most potential reservoir rocks are heterogeneous, relationships between the physical properties are very complex and thus far no satisfactory correlations based on theory or laboratory models have been developed. It appears that empirical relationships obtained by measuring the physical properties of a large number of samples of naturally occurring porous media and applying regression analysis to develop equations for one physical property in terms of other rock properties is the best approach. REVIEW LITERATURE The three physical properties used as dependent variables for correlating purposes were porosity, permeability and formation factor. Since formation factor is more difficult to determine, a brief review of the literature is provided on this property. The first work on determining formation factors was published by Archie1 in 1942. He defined this property of a porous medium as F - Ro/Rw......(1) where Ro is the resistivity of the porous medium when completely saturated with a brine of resistivity Rw. Archie found the best correlation between formation factor and porosity was the following equation, where is the porosity fraction and m is the constant characteristic of the rock. The value of m was 1.3 for unconsolidated sand packs, and ranged from 1.8 to 2.0 for consolidated sandstones. In 1950 Patnode and Wyllie2 and De Witte3 observed that the formation factor as determined by Eq. 1 was valid only when the porous medium contained no conductive solids such as clay or shale. When conductive solids are present the formation factor is also dependent on the resistivity of the saturating fluid. Therefore, in samples containing conductive solids the formation factor decreased as the resistivity of the saturating fluid increased. Because of this. the measured formation factor was called the apparent formation factor and was designated Fa. Patnode and Wyllie proposed the following equation,

By R. Chanchani

It was reported earlier that francolite and dolomite from south Florida deposits cannot be selectively floated using conventional conditioning with sodium oleate as the collector. However, dolomite could be separated from francolite if the minerals were first conditioned at pH 10 followed by reconditioning at a lower pH. An optimum separation was achieved after reconditioning at a pH below 4.5. Reconditioning pH and collector concentration were determined to exert a major influence on the selectivity. Flotation, adsorption, and transmission infrared spectroscopic results are presented to elucidate the mechanisms underlying the observed selectivity.

Jan 1, 1986

By P. C. Badgley

The purpose of this paper is to demonstrate the usefulness of systematic analyses of weakness patterns. The term weakness here includes structural features such as fractures, foliation planes, lineaments and bedding. Many of these features are mapped by geologists in the field, but analysis of the field date is frequently overlooked. Examples are presented to show the value of such studies in petroleum and mineral exploration, in dam site selection, and in regional tectonic interpretations. Numerous theories have been presented to account for the mechanics and time of origin of fracturing. This is an extensive subject and cannot be reviewed in detail here. The reader may wish to refer to other papers.*"5 It is sufficient to say that most fracture patterns can be related to one or more of the following force mechanisms: compression, tension, torsion and fatigue (inheritance by upward propagation of pre-existing fractures). Fractures generally occur in sets in a district. The angular relationships and other characteristics of the individual sets frequently help in determining the force mechanism and movement history of the deformation. From a geometric point of view fractures are commonly referred to as longitudinal, cross, or diagonal (shear), depending upon their orientation relative to other major structural features such as anticlinal axes and so forth. These terms will be used from time to time and are illustrated schematically in Fig. 1. FIELD PROCEDURE AND TREATMENT OF DATA In fracture studies it is very important to collect adequate field data. Fig. 2 illustrates a notebook sheet for recording significant field observations in sedimentary rocks. Slight adaptations have to be made for igneous and metamorphic terrains. Fracture density and persistence are very important factors in petroleum exploration for fractured reservoirs and mineral exploration. The density for each joint set is recorded in terms of number of joints per linear yard. The total number of joints at any one

Jan 1, 1962

By W. G. Fischer

This paper attempts to close the gap between extensive rock testing with field measurements and the mine operator's need for safe mine layouts and alternatives. It was found that many of the variables that influence mine geometry and worker safety are relatively unimportant while others are critical. The development of empirical relationships that tie the critical variables to the safe useful life of a trona mine layout and observations made in 140 production areas where the variables were researched over a 15-year period are discussed. The concepts presented may have applicability in mine design for other bedded deposits.

Jan 1, 1986

By M. D. Flavel

The paper describes the physical aspects of the compression and impact crusher types along with the information needed to apply, install and operate them to best achieve designed performance levels. It reviews key performance parameters such as energy size relationships for crushing processes and how automation devices can optimize machine productivity. Weaknesses of existing application engineering methods are discussed. The use of pilot plant information and appropriate laboratory testing procedures are reviewed from the point of view of the application design engineer so that the best type of machine can be selected for a proposed installation.

Jan 1, 1982

By Stanley C. Herold

At the present time five localities in the Argentine Republic are known to bear direct evidences of the presence of petroleum. The segregation of these localities is more or less arbitrary inasmuch as minor indications may be found to extend from one locality to the other at no regular distance apart, especially in the northern and western part of the republic. These localities are listed as follows: North Argentine-Bolivian region, Salta-Jujuy district, provinces of Mendoza and Neuquen, Comodoro Rivadavia, and the Gallegos-Punta Arenas region. Economic conditions attract us to the possibilities of developing these and other regions of countries in the southern hemisphere. Development work will, naturally, be undertaken first in such localities as present direct manifestations of the presence of petroleum; "hidden fields" may exist, but, unless discovered by accident, their development will be left to the last. The problems to be solved in the development of the petroleum resources of the Argentine republic are mainly of stratigraphy, structure, and transportation. We are not here concerned with the unfavorable climate of the countries to the north in the tropics where, for us of the "far north," life hangs by a thread ready to be severed by a mosquito, gnat, or tropical germ. North Argentine-Bolivian Region The North Argentine-Bolivian region has already been described by the author.' Geographically and geologically this is admittedly one field extending from Argentine into Bolivia. It is not necessary to repeat here the various conditions pertaining to this field, though the summary may be quoted as follows: Extending from northern Argentine northward into central Bolivia is a belt of petroleum seepages. On account of the remoteness of the district it has, heretofore, been little considered by oil operators. The regional geology is comparatively well understood but the local features have not been carefully detailed. Development work in the past has been done on an unscientific basis and has led to failures. At the present time, access to the region is somewhat difficult but, no

Jan 1, 1921

By R. R. Hawkins

PEoperly designed tubing strings make it possible to continue the flowing life of wells beyond the stage where ordinarily they would be put to pumping. Wells no longer able to flow through 2-in. tubing can be made to produce through smaller tubing if conditions within the well are carefully studied and correctly designed strings are installed. In this way, pumping expense may be postponed and in some pools it is within reason that the entire recovery may be obtained by natural flow if maintenance of pressure is practiced. Infrequent tubing changes would be necessary but their cost would be much less than that of installing and maintaining pumping equipment. If small wells are to be made to flow naturally, careful consideration must be given the actual lifting mechanics within the string, so that fairly accurate knowledge of reservoir conditions, especially pressure, is essential. Wells producing between 5 and 25 bbl. daily are classified here as "small wells." Exponential Flow A maximum of the energy contained in the expanding gas must be employed to do useful work if natural flow is to be continued. It is evident that adiabatic expansion would defeat this purpose, therefore the velocity of the gas must be held down to a minimum in order that isothermal expansion may be approached. Of course, true isothermal expansion would not be obtainable in an oil well, hence the use of the term "exponential." 1 Obviously the closer the approach to isothermal expansion, the more efficient the lift. Experiments by the U. 8. Bureau of Mines² have shown that for isothermal expansion to take place in a gas well where water is being produced, a definite relationship exists between the depth of the well and the minimum operating pressure. The latter must be such that the tubing fill-up, if static conditions prevailed, would be equivalent to 14 per cent of the distance between the top of the fluid inside the tubing and the tubing head. It has been observed that variations in this essential ratio

Jan 1, 1932

By E. Hoek

INTRODUCTION Rock slope stability research has been in progress for the past four years at the Royal School of Mines in London under the sponsorship of a consortium of 23 companies* with interests in open pit mining. This paper reviews the principal aims and achievements of this research project. In order to assist the reader in following these details, the basic philosophy underlying the formulation and direction of this research project is discussed. DISTRIBUTION OF RESPONSIBILITY In open pit mining, the economic necessity of keeping waste rock removal to a minimum generally means that the mine slopes have to be excavated to the steepest possible slope angle. On the other hand, excessive steepening of these slopes can induce failures, which may negate the economic benefits that have been aimed at and which may also result in loss of life and damage to equipment. Consequently, where slope failures are likely to prove to be a problem, an evaluation of the stability of the slopes to be created should be included as part of the overall pit design. How is the stability of a rock slope evaluated? When this question was examined, during discussions on the research policy to be followed at the Royal School of Mines, it was clear that relatively few satisfactory techniques were available in a form that would be comprehensible and therefore useful to the practical mining engineer. It was recognised that the research project must be directed towards two distinct aims: a) The evaluation of existing techniques for rock slope stability analysis and the provision of new techniques where these existing methods were found to be inadequate and b) The presentation of the results of this evaluation and research in a form that would be useful to engineers without specialist training in rock mechanics. It was soon realized that a university based research team, however large and efficient, could not achieve these aims without the co-operation and assistance of mining engineers,

Jan 1, 1972

The fourth National Exposition of Chemical Industries will be held in the Grand Central Palace, New York, during the week of Sept. 23, 1918. Dr. Bacon, of the advisory committee, is now head of the Chemical Warfare Section of the National Army, and a member of General Pershing's staff. The coming Exposition will be the largest ever held, and it will be necessary to use four floors of the Grand Central Palace. The exposition is a war-time necessity, and regarding it as such, each exhibitor is planning his exhibit so that it will be of. the greatest benefit to the country.

Jan 8, 1918

By J. R. Slotemaker

As successfully pilot-tested at a quarry producing limestone for a large cement plant, swiftly flowing streams of rock enter the Gromax Selector. They are electronically scanned while in motion and light reflection data flashed to logic circuits. The logic circuits compute the total light deviations in each rock as it passes the scanner. Thus, a rock with striated or spotted impurities can be rejected or accepted on the basis of its proportional content. The actual case history of this equipment's development at a limestone quarry in the Southeast serves to illustrate its general area of usefulness.

Jan 1, 1964

By E. J. Haug, M. M. Fine

For several years work has been carried on by the U.S. Bureau of Mines at Rolla, Mo., to develop improved methods of concentrating the oxidized ores of lead and zinc. Various samples have been investigated, and results on some have been published. Details of the progress to date are given in a mineral dressing study now being conducted for an extensive oxidized lead-bearing tract in southeast Missouri, property of St. Joseph Lead Co. These oxidized ores present problems typical of many encountered in modern mineral dressing research in that recovery of very fine particles is of

Jan 4, 1955

By Garfield Schnee

MACHINERY has not taken the place of manual labor in steep pitch coal in the anthracite field and there is a shortage of miners experienced in this type of work. To overcome these difficulties several coal companies have resorted to different types of mining such as the diamond or zig-zag method, the slant method, long hole drilling, and several other variations. For the past 5 years the diamond shape method has been used extensively in the heavy pitching beds of both the Knickerbocker and Yatesville basins at Knickerbocker colliery of the Philadelphia & Reading Coal & Iron Co.

Jan 10, 1950

By E. J. Haug, M. M. Fine

FOR several years work has been carried on by the U.S. Bureau of Mines at Rolla, Mo., to develop improved methods of concentrating the oxidized ores of lead and zinc. Various samples have been investigated, and results on some have been published 1,2 lished.l, 2 Details of the progress to date are given in a mineral dressing study now being conducted for an extensive oxidized lead-bearing tract in southeast Missouri, property of St. Joseph Lead Co. These oxidized ores present problems typical of many encountered in modern mineral dressing research in that recovery of very fine particles is of

Jan 1, 1956

By B. R. Eichbaum, J. E. Murphy, J. A. Eisele

The US Bureau of Mines demonstrated ferric chloride leaching of galena concentrate on a continuous bench scale basis. Leaching was performed at 95°C (200°F) and with a contact time of 15 minutes. The ferric chloride leaching solution was continuously fed to a leaching tank at a constant rate for periods up to 45 hours. In each test, a constant redox potential was maintained in the slurry exiting the leaching tank by controlling the concentrate feed rate. In the 45 hour test, lead extraction exceeded 99.5%, and the lead chloride produced was 99.97% pure.

Jan 1, 1986

By C. F. Chung

This paper will discuss an application of multivariate discriminant analysis to aid in predicting mineral potential from regional geological data and information on mineral deposits, with particular emphasis on the use of the logistic discriminant function. Logistic discriminant analysis is a generalization of standard discriminant analysis in that the discriminant analysis becomes applicable under a much wider class of distributions. As a practical example, the standard multiple discriminant analysis and the logistic discriminant analysis are applied to data from the Bathurst area in the Appalachian region of Canada and the results are compared with one another.

Jan 1, 1977

By Merle L. Bowser, Lawrence W. Scott, John N. Murphy

The environmental status of underground mining operations is critical to the health and safety of the miners; particularly in a large mine, the multitude of interacting parameters that can favorably or adversely affect the environmental status makes the manpower requirement of the routine checking of specific areas and conditions a formidable one. While the concept of environmental monitoring for miners has been considered for some time, until recently the availability of sensors to reliably measure the parameters of interest severely limited the utility of such systems. The status of sensors for mine use and the evaluation of enviornmental monitoring systems is reviewed.

Jan 1, 1980

By Merle L. Bowser, Lawrence W. Scott, John N. Murphy

The environmental status of underground mining operations is critical to the health and safety of the miners; particularly in a large mine, the multitude of interacting parameters that can favorably or adversely affect the environmental status makes the manpower requirement of the routine checking of specific areas and conditions a formidable one. While the concept of environmental monitoring for miners has been considered for some time, until recently the availability of sensors to reliably measure the parameters of interest severely limited the utility of such systems. The status of sensors for mine use and the evaluation of environmental monitoring systems is reviewed.

Jan 9, 1979