Search Documents

By A. B. Tanner

The effects of radon in drillholes on gamma-ray logs have been described by L. S. Hilpert and C. M. Bunker1 Since these effects may cause drastic error in the evaluation of uranium deposits, it is useful to know the conditions under which significant amounts of radon tend to accumulate in drillholes. In the studies described here, atmospheric conditions were found to dominate in the control of the behavior of radon in drillholes in the vicinity of a uranium orebody. The site of the investigation was in McKinley County, New Mexico, about 12 miles north of Grants. Drillholes of 4 1/4-in. diam, on 25-ft and 100-ft centers, penetrate ore in dry rock at a depth of about 100 ft. A geologic log of the drillhole of primary interest is shown in Fig. 1. Gamma-ray logs revealed three zones of ore-grade mineralization in the Todilto limestone. A 6-ft zone, the lowest of the three, assayed 0.20 pct U3O8 by chemical analysis. The limestone ores in this area contain disseminated uraninite and some yellow and orange secondary minerals. Only radon"", a member of the uranium'" series, was measured in this investigation. Radon is one of the chemically inert noble gases and is radioactive by alpha particle emission with a half life of about four days. In this discussion, amounts of radon are expressed in microcuries (1 microcurie equals 37,-000 disintegrations per sec) and concentrations of radon are expressed in microcuries per liter of drillhole air. Samples of air were obtained by lowering a sampling device (Fig. 2) into a drillhole and actuating the device at the desired depth. It was then raised to the surface and the sample was transferred to a storage tube. Within two days the sample was transferred to an ionization chamber, and the activ- ity of radon and its short-lived daughter products was measured at radioactive equilibrium with a vibrating-reed electrometer. The measurements were corrected back to the time of collection and involve errors estimated generally not to exceed + 5 pct to —15 pct. Radon Behavior in a Covered Hole: Fig. 3, a typical log of radon concentration vs depth in the covered drillhole, was made by using values of radon concentration at discrete depths. Continuous logs of alpha-particle radiation in the drillholes showed that such radon logs depict the continuous variation of radon concentration with depth quite accurately. Three features of radon logs were noted: 1) maximum

Jan 1, 1960

SULPHUR is a very well known mineral and apparently is produced in many places. It is engendered from an unctuous earthy and powerfully hot substance so that it is considered among experienced workers to bear a resemblance to the element of fire. This is called by these same men the masculine seed and the prime agent of Nature in the composition of metals. Because of its great dryness and heat it has, as experience shows, affinity with fire, which is easily introduced in it when brought near. And once introduced the fire is quenched only with difficulty before its unctuousness is wholly consumed. Although it shows itself to us of such a hot and dry nature, we must not think that sulphur is a substance so pure that it can stand by itself or that in order to attain its form it has no need of its portion and part of moisture like every other mixture. This is shown to us by its easy fusion, in which it resembles the metals. This thing is found in many places and in many varieties of color; some are white, others yellow and orange, and some others between gray and black. They also say that some red is found. It does not occur in that arrangement of veins like other minerals, but most liberal Nature makes whole mountains of it as is seen in the Aeolian islands, [26] near Sicily, in Etna or Moncibello which is the island of Sicily, at Pozzuoli, in the territory of Rome, in the Sienese domain at San Filippo, and in many other similar places. It is a substance that has a very strong odor and is most unpleasant to smell. It is very fixed in its substance so that it is never corrupted by time, by boiling, or by the moisture of water. For although it may stand in water a long time it never becomes soft nor does it ever decrease or increase in weight. It is brittle and easily crushed very fine. It is said that a trace of garlic rubbed on the mortar helps anyone who wishes to reduce it to impalpability. Its ores have a form more like earth than like stone although they some¬times have the color of a certain soft rock. The places where it is found are easily recognized by the great odor that they give out and by the very hot baths that often spring forth near it. What I have already told you about quicksilver that is contrary to the

Jan 1, 1942

By Edward Wisser

The environment of an ore body is taken to mean not only its physical surroundings but every factor, passive or active, that conditioned the ore shoot, saving only the original composition of the solutions that formed the shoot. Collection of data related to the shape and characteristics of veins should be followed by correlation of the data and the formulation of generalizations regarding ore formation. The nature of the criteria used in arriving at these generalizations is discussed. Certain of the criteria, when used with an understanding of their underlying causes, become "ore-guides." In the course of his study the geologist must not confine himself to the immediate surroundings of the veins, but should attempt to work out the geologic history of events culminating in the crucial epoch for any mining district, the period of mineralization. The work may involve study of features far removed from the veins and related to them only indirectly. It commonly means thorough study of the geology of the entire region surrounding the ore deposits. The following question has been suggested for discussion: "Are there any criteria by which one can determine when mining operations have reached the roots of an ore deposit?" The question deals less with the roots of a particular ore body than with the lower limit of the vertical range within which ore bodies may be expected. It concerns a critical line upon the longitudinal vertical projection of a vein.† Below this line it is useless to look for ore shoots; above the line exploration below the bottoms of individual ore shoots may be justified. Can we learn to determine the position of such a line? In some multivein districts the line for any given vein may be approximated by simple interpolation or extrapolation. Where this is possiblc the bottoms of the lowest ore shoots in the various veins are points on an imaginary, gently rolling surface. The trace of this surface upon the vein is our critical line for that vein. The imaginary surface rolls so gently that it may be projected from two or more known veins to an unexplored vein near by. Here is a criterion for the bottoming of ore that has nothing to do with changes in the appearance of the vein in question; it rests solely on the depth at which the ore bottomed in adjacent veins. The method is not applicable in districts only slightly explored in depth, nor where the lower limit of the ore-bearing horizons

Jan 1, 1941

By Edward Wisser

The environment of an ore body is taken to mean not only its physical surroundings but every factor, passive or active, that conditioned the ore shoot, saving only the original composition of the solutions that formed the shoot. Collection of data related to the shape and characteristics of veins should be followed by correlation of the data and the formulation of generalizations regarding ore formation. The nature of the criteria used in arriving at these generalizations is discussed. Certain of the criteria, when used with an understanding of their underlying causes, become "ore-guides." In the course of his study the geologist must not confine himself to the immediate surroundings of the veins, but should attempt to work out the geologic history of events culminating in the crucial epoch for any mining district, the period of mineralization. The work may involve study of features far removed from the veins and related to them only indirectly. It commonly means thorough study of the geology of the entire region surrounding the ore deposits. The following question has been suggested for discussion: "Are there any criteria by which one can determine when mining operations have reached the roots of an ore deposit?" The question deals less with the roots of a particular ore body than with the lower limit of the vertical range within which ore bodies may be expected. It concerns a critical line upon the longitudinal vertical projection of a vein.† Below this line it is useless to look for ore shoots; above the line exploration below the bottoms of individual ore shoots may be justified. Can we learn to determine the position of such a line? In some multivein districts the line for any given vein may be approximated by simple interpolation or extrapolation. Where this is possiblc the bottoms of the lowest ore shoots in the various veins are points on an imaginary, gently rolling surface. The trace of this surface upon the vein is our critical line for that vein. The imaginary surface rolls so gently that it may be projected from two or more known veins to an unexplored vein near by. Here is a criterion for the bottoming of ore that has nothing to do with changes in the appearance of the vein in question; it rests solely on the depth at which the ore bottomed in adjacent veins. The method is not applicable in districts only slightly explored in depth, nor where the lower limit of the ore-bearing horizons

Jan 1, 1941

By Edward Wisser

The environment of an ore body is taken to mean not only its physical surroundings but every factor, passive or active, that conditioned the ore shoot, saving only the original composition of the solutions that formed the shoot. Collection of data related to the shape and characteristics of veins should be followed by correlation of the data and the formulation of generalizations regarding ore formation. The nature of the criteria used in arriving at these generalizations is discussed. Certain of the criteria, when used with an understanding of their underlying causes, become "ore- guides." In the course of his study the geologist must not confine himself to the immediate surroundings of the veins, but should attempt to work out the geologic history of events culminating in the crucial epoch for any mining district, the period of mineralization. The work may involve study of features far removed from the veins and related to them only indirectly. It commonly means thorough study of the geology of the entire region surrounding the ore deposits. THE following question has been suggested for discussion: [t] "Are there any criteria by which one can determine when mining operations have reached the roots of an ore deposit?" The question deals less with the roots of a particular ore body than with the lower limit of the vertical range within which ore bodies may be expected. It concerns a critical line upon the longitudinal vertical projection of a vein.[t] Below this line it is useless to look for ore shoots; above the line exploration below the bottoms of individual ore shoots may be justified. Can we learn to determine the position of such a line? In some multivein districts the line for any given vein may be approximated by simple interpolation or extrapolation. Where this is possible the bottoms of the lowest ore shoots in the various veins are points on an imaginary, gently rolling surface. The trace of this surface upon the vein is our critical line for that vein. The imaginary surface rolls so gently that it may be projected from two or more known veins to an unexplored vein near by. Here is a criterion for the bottoming of ore that has nothing to do with changes in the appearance of the vein in question; it rests solely on the depth at which the ore bottomed in adjacent veins. The method is not applicable in districts only slightly explored in depth, nor where the lower limit of the ore-bearing horizons

Jan 1, 1939

By Kenneth E. Kulp, Theodore Botinelly, George J. Neuerburg

Distribution of hypogene iron oxides may be useful in prospecting the Montezuma district, central Colorado, for certain metals, some of which have not been mined or sought in the district. The depletion of accessory magnetite in fresh rocks of the Montezuma stock identifies sources of ore minerals for the pneumatolytic metals, locates probable areas of possible contact-pneumatolytic deposits, and, in the altered rocks of the stock, identifies rock through which hydrothermal ore fluids have passed. Specularite veins are located in structures through which pneumatolytic ore fluids have passed and thus indicate optimal areas for prospecting. The presence of unusual amounts of vicarious metals such as bismuth, mercury, tin, and tungsten serves to identify magnetite and specularite that were involved in the pnematolytic ore process.

Jan 1, 1972

By S. R. du Toit, W. J. Oberholzer, M. I. Watson, D. G. Krige

The objectives, essential features and implications of the 'random' and 'deterministic' types of ore value surfaces are examined as well as the basic requirements for a satisfactory prediction model. The 'random' method used on the South African gold mines and based on observed auto-covariance patterns is briefly discussed as well as its justification in preference to the 'deterministic' approach. Various mathematical models for auto-covariance patterns are examined for the one-dimensional case. It is also shown that these patterns as estimated for ore values in certain mines agree closely for various sizes of ore unit. In two case studies the variations in gold, uranium and ore thickness covariance patterns are examined and compared with certain geological features established independently from sedimentological studies.

Jan 1, 1969

By J. O. Lewis

Oil wells usually reach their maximum daily output shortly after they are completed. From that time they decline in-production, the rapidity of decline depending on the output of the wells and on other' factors governing their productivity. The production curve of a well shows the mount of oil produced per unit of time for several consecutive periods; if the conditions affecting the rate of production are not changed by outside influences, the curve will be fairly regular, and, if projected, mill furnish useful knowledge as to the future production of the well. By the aid of this knowledge the value of a property may he judged, and proper depletion and depreciation charges may be made on the books of the

Jan 2, 1918

* A demonstration pipeline for transporting coal will be constructed by Pittsburgh Consolidation Coal Co, at the Georgetown strip-mining operation near Cadiz, Ohio, The 12-in., 17,000-ft line, special crushing and preparation equipment, and pumps especially designed for the operation will cost about $550,000. A slurry of fine coal and water will be fed into the line and moved through it under pressure. * Sulphur resources in the U.S. are being rapidly exhausted with no new major deposits being found, This common mineral may become one of the most strategic items during the next five years. Recovery of sulphur from pyrites is being considered in case of an emergency. Already the British have adopted stringent measures to conserve sulphur supplies.

Jan 3, 1951

By W. E. Field

In the Coast Mountains approximately 110 miles north of Vancouver, the gold mine of Bralorne- Pioneer Mines Ltd. lies at an elevation of 3500 ft. The deepest or 41 level in the mine is at an elevation of 1400 ft below sea level, and the rock temperature on this level is 122.5°F. The thermal gradient is 1 "F increase in temperature for each 67.5 ft increase in depth. The mine produces between 500 and 600 tons per clay, utilizing an adit two internal shafts, and one service shaft from surface. The Queen shaft, extending from the 26 to the 41 level, IS the deepest, and most production now comes from this area. Stoping in by cut and fill using mill tailing hydraulic backfill.

Jan 12, 1963

By Joseph Hartshorne

The nature if this process and the general course of its development have already been described by me in two papers read before the Institute.* Since the latter paper mas read, in February, 1898, the development at Kladno has been almost altogether in the direction of using metal direct from the blast-furnace. This has now been the regular practice for about a year. The molten metal is brought from the furnace in ladles, without the intervention of any mixing- or accumulating-reservoir. The plant remains practically the same as originally described by me,† except that the primary furnace has been enlarged as much as was permitted by the existing conditions. This was done primarily in order to increase the capacity of the

Jan 1, 1901

By M. S. Klima, P. T. Luckie

An evaluation of the operating performance of a recently designed pneumatic centrifugal classifier is presented. This classifier has been modified from a separate air and feed input design to an entrained solids in air feed input. The evaluation first required determining the size distributions for the three streams (feed, fine, and coarse). Using size distribution data and mass flow rates, a size selectivity curve was calculated for each operating condition tested. This curve, in turn, was characterized by appropriate selectivity parameters (i.e., the equiprobable or cut size, the sharpness index, and the apparent bypass values). The variation of these parameters with classifier operating conditions was examined. From these evaluations, the "best" operating conditions for the classifier were then determined.

Jan 1, 1985

By Douglas W. Fuerstenau, Kalanadh V. S. Sastry

Mathematical considerations of green ball growth in a balling device by the mechanisms of layering new feed onto seed or recycle pellets are presented. An experimental procedure was developed for investigating the agglomerate growth by layering in which the addition of feed to a batch of seed pellets was made cyclically. Using this procedure, the layering growth mode under partial feed consumption and no seed generation conditions was investigated experimentally in a laboratory balling drum as a function of such operating variables as moisture content of the material, feed rate, and the size distribution of the seed pellets. The experimental results were analyzed in the context of the model equations and the layering growth constant was estimated as a function of the operating variables.

Jan 1, 1978

By James E. McNulty

Coal reserve estimates are prepared using a simple equation: the product of area, bed thickness, density and recovery factors. Each of these elements involves a degree of risk based on certain assumptions. Reserve area, thickness and density rely on certain physical data whose accuracy, reliability and sufficiency may be problematical. Estimates of recovery factors for mining and coal preparation are often subjective. Most reserve estimates assume, sometimes incorrectly, that the subject reserves will be completely extracted. The principle that certain coal resources are reserves, if they can be considered economically recoverable at the time of determination, needs to be reexamined in the light of recent market cycles. Reserve estimating requires the exercise of judgments, the validity of which reflect the qualifications, experience and objectivity of the estimator.

Jan 1, 1985

By K. V. S. Sastry, S. C. Panigraphy, D. W. Fuerstenau

The batch balling behavior of hematite, magnetite and limestone was found to depend markedly on the grinding method used for feed preparation. Wet ground materials require higher moisture for balling than do dry ground materials. Further, as the fineness of the wet-ground material is increased, the overall rate of agglomeration decreases, whereas the opposite is true for dry-ground materials. In contrast, the resulting pellet size distributions are not affected by the nature of the feed material preparation. These differences and similarities in the agglomeration behavior between wet and dry ground materials may result from the hydrophilic/hydrophobic nature of the surfaces, the formation of pre-agglomerates during dry comminution, and possible variations in the packing density of particles in the agglomerates.

Jan 1, 1978

By Peter Joraleman

Man has always felt more comfortable breaking his life into categories or classifications. An otherwise bewildering life somehow becomes easier to bear when divided into neat measurable sections, each of which is fitted into its proper niche. It seems likely that the world's first economic geologist, when faced with the world's first two ore bodies, started his career by classifying them. Early on, he divided his ore bodies into those born of water, of fire, and of air. In retrospect this threefold classification was probably about as useful as the more complex ones that followed. This division of ore bodies probably did not help him in his search for new deposits, but it made him feel more secure in dealing with those already known.

Jan 12, 1975

By J. Laskowski, Z. Sadowski

The properties of quartz, calcite, magnezite and dolomite suspensions prepared from -30 µm size fractions of these minerals have been investigated. Selective coagulation of the quartz-calcite, quartz-magnezite and quartz-dolomite binary suspensions was possible at the pH values slightly above those for the i.e.p. of the carbonate minerals. The tests revealed that quartz suspensions were not flocculated by the anionic flocculants, whereas the same polymers were flocculants for calcite, magnezite and dolomite. Selectivity in the flocculation of the quartz-calcite, quartz-magnezite and quartz-dolomite binary suspensions was not, however, satisfactory because of the activation of quartz by ca2+ and Mg2+ ions. Dispersing reagents can be used to improve the selectivity of flocculation.

Jan 1, 1980

By T. W. Peterson, J. W. White, E. E. Krist

In developing a minicomputer application for an industrial grinding circuit, the control program is usually coded and the compilation is debugged on a remote access computing system. Final debugging must wait for installation of the minicomputer. This work reports on an alternative. Here both compilation and execution bugs are eliminated before the hardware is installed by testing the control program against a dynamic simulation. Attention is directed toward development of a particular real-time control program for an industrial wet grinding circuit in a copper concentrator. Specific data were supplied by the Anamax Mining Co. for a grinding division consisting of a rod mill followed by two ball mills in parallel. This information was used to set up a plausible model structure.

Jan 1, 1977

By J. L. Huiatt, G. M. Potter, R. B. Tippin

The US Bureau of Mines and Great Salt Lake Minerals and Chemical Corp. have developed a froth flotation process for concentrating potassium salts from Great Salt Lake solar evaporites containing about 6% K2O. The crude evaporites, which were predominately halite (NaCl) with smaller amounts of kainite (KCl.MgS0, 2.7Hp0) and schoenite KeS0,MgS04.6H,0), were conditioned in a saturated brine solution., thus converting nonfloatable kainite to the floatable mineral schoenite. Schoenite was then selectively floated with a medium-molecular-weight fatty acid. Continuous small-scale pilot-plant testing indicated that 80% of the potassium could be recovered from the crude evaporites in flotation concentrates assaying about 13% K2O.

Jan 1, 1976

By G. M. Ritcey

Purification of solutions can involve various treatment methods. In the normal sequence of metals recovery by hydrometallurgy, the ore is initially prepared for leaching by grinding to the desired optimum mesh size as dictated by the leaching parameters. Following leaching and liquids- solids separation, the resultant solution is ready for purification. The use, or introduction of solvent extraction into a plant, can be either a major or a minor part of the metal recovery process as shown by the following list where solvent extraction is normally considered: a) recovery of a metal by a simple leaching of the broken ore, e.g., copper from dump leaching where there are only the three main steps of leaching, solvent extraction, and electrowinning (1);

Jan 1, 1978