Search Documents

By M. T. Martinson, I. W. Nicholson, C. J. Chindgren, F. P. Williams, L. C. Bauerle, S. F. Ravitz

THE vanadiferous shales of southeastern Idaho and southwestern Wyoming constitute the largest known reserve of vanadium in the United States.1 These deposits have never been exploited except for the relatively small amounts of vanadium recovered by the Anaconda Copper Mining Co. in the treatment of phosphate rock from southeastern Idaho. The major domestic source of vanadium has been the sandstone ores of southeastern Utah and southwestern Colorado. Early in World War II, it appeared that these ores could not meet the greatly increased demand for vanadium, so the investigation described in this report was undertaken to develop processes for the recovery of vanadium from the Idaho-Wyoming deposits. The utilization of these deposits became unnecessary, however, because of greatly expanded production from the Utah-Colorado sandstone ores and the continued availability of vanadium from other sources, chiefly Peru. The major use of vanadium is as an alloying agent in the manufacture of high-quality steels. Vanadium constructional steels usually contain 0.05 to 0.20 pct vanadium, which refines the grain and increases the strength, elastic limit, and resistance to shock and fatigue. Vanadium tool steels not used in high-speed work contain 0.10 to 0.60 pct whereas high-speed tool steels contain 1.0 to 4.0 pct. Vanadium compounds are used as catalysts (principally for the oxidation of SO2 to sulphuric acid and of naphthalene to phthalic acid) and in the paint, chemical, ceramic, dye, and printing industries. The selection of the particular ore deposit to be exploited would involve consideration of many factors besides the metallurgical results that might be obtained. Chief among these would be the reserves of ore available, the grade of the ore, and the mining costs. As very little was known about any of these factors, it was necessary to investigate methods of treatment of all the ores under consideration, working with samples obtained in the course of the exploration work, even though they were not positively representative of the whole deposit from which they were taken. Because of wartime conditions prevailing when this investigation was started, first consideration was given to processes that could be put into operation most quickly and would involve minimum use of strategic materials, even though these processes might not be the most economical.

Jan 1, 1947

By M. T. Martinson, I. W. Nicholson, C. J. Chindgren, F. P. Williams, L. C. Bauerle, S. F. Ravitz

The vanadiferous shales of southeastern Idaho and southwestern Wyoming constitute the largest known reserve of vanadium in the United States.' These deposits have never been exploited except for the relatively small amounts of vanadium recovered by the Anaconda Copper Mining Co. in the treatment of phosphate rock from southeastern Idaho. The maior domestic source of vanadium has been the sandstone ores of southeastern Utah and southwestern Colorado. Early in World War 11, it appeared that these ores could not meet the greatly increased demand for vanadium, so the investigation described in this report was undertaken to develop processes for the recovery of vanadium from the Idaho-Wyoming deposits. The utilization of these deposits became unnecessary, however, because of greatly expanded production from the Utah-Colorado sandstone ores and the continued availability of vanadium from other sources, chiefly Peru. The major use of vanadium is as an alloying agent in the manufacture of high-quality steels. Vanadium constructional steels usually contain 0.05 to 0.20 pct vanadium, which refines the grain and increases the strength, elastic limit, and resistance to shock and fatigue. Vanadium tool steels not used in high-speed work contain 0.10 to 0.60 pct whereas high-speed tool steels contain 1.0 to 4.0 pct. Vanadium compounds are used as catalysts (principally for the oxidation of SO2 to sulphuric acid and of naphthalene to phthalic acid) and in the paint, chemical, ceramic, dye, and printing industries. The selection of the particular ore deposit to be exploited would involve consideration of many factors besides the metallurgical results that might be obtained. Chief among these would be the reserves of ore available, the grade of the ore, and the mining costs. As very little was known about any of these factors, it was necessary to investigate methods of treatment of all the ores under consideration, working with samples obtained in the course of the exploration work, even though they were not positively representative of the whole deposit from which they were taken. Because of wartime conditions prevailing when this investigation was started, first consideration was given to processes that could be put into operation most quickly and would involve minimum use of strategic materials, even though these processes might not be the most economical.

Jan 1, 1949

By Heinrich Ries

Fullers' earth is a clay-like substance, which has the property of decolorizing or clarifying oils. An ultimate chemical analysis shows it to differ from most ordinary clays in having usually a high percentage of combined water and a low amount of alumina. There is probably a large amount of hydrous silica present. Fullers' earth possesses little or no plasticity, and in order to work properly has to be ground very fine. A chemical analysis is of little value at present in determining its quality; only a practical test suffices. Up to about two years ago all of the fullers' earth used in this country was imported from England; but about that time deposits were discovered in Florida, "† and since then rumors of its occurrence have been coming from all parts of the country. Next to the Florida deposits of fullers' earth, those of South Dakota are the most extensive thus far discovered in this country. The earth was first discovered near Fairburn, Custer county, and other deposits have since been prospected at Argyle, Minnekahta and other localities. Fairburn.—One of the first deposits located and opened up is five miles southeast of Fairburn, Custer county. The mine is a mile from the Fremont, Elkhorn and Missouri Valley Railroad, and the section exposed shows, beginning at the top: Feet. Micaceous sandy clay,......... 6 Fullers' earth,..........9 Micaceous sandstone,......... The fullers' earth passes upwards into the sandy clay, but in its purer portions it is a yellowish, gritty clay, with a somewhat

Jan 1, 1898

By Robert P. Koenig

FOR the first time other than on occasion of war the people of the United States are experiencing full-scale participation in world affairs. Public concern has seldom been so involved with conditions and events beyond our own continental limits. Our interest is not wholly of recent origin. Over the years the activity of the United States as a world power and an important trading nation brought about the widening of our political interests and the progressive interrelation of our economy with that of the rest of the world. Some may see in our present phase of world-wide activity the natural consequence of our continued growth. Such observers must also be aware that within recent years our importance in world affairs has been considerably increased. For within the space of an extremely short period events have occurred that have literally jet-propelled the United States into the role of a leading participant in the conduct of world affairs. Little of the choice of this role was left to us. The decline of power in western Europe, the ascendancy between the Elbe and the Pacific shore of an obviously antagonistic force, our earnest endeavor to secure international control of atomic energy, the necessity of providing relief and rehabilitation to war-ravaged areas, and the police work that must be done in occupied territories are problems which have risen in great measure without our help-but they cannot be solved without it.

Jan 1, 1948

By L. E. Young

GERMANY'S recent collapse and the occupation by the Allies of the coal fields of the Ruhr, the Saar, Silesia, Poland, and Czechoslovakia have focused attention on the postwar coal problems of Europe. American coal operators are interested deeply in what is happening in Britain, particularly in the discussion of plans to rehabilitate and reorganize the entire British coal mining industry, as such reorganization will probably determine the place Britain will occupy in the European coal markets for the next few decades. The continuing decline of British out-ut per man-shift, particularly during wartime, has resulted in a most serious effort to determine whether this unfortunate trend is due to the physical condition of the coal seams, poor management, poor engineering and planning, inadequate use of power and machinery, or failure of labor to co-operate with management.

Jan 1, 1945

By W. F. Chiao

Ultrasonic attenuation, a, measurements in the frequency range of 5 to 55 mc per sec have been studied to determine their quantitative relationship with the following three variables of mixed microstructures in steels: 1) the volume percent, XF, of polygonal fer-rite in mixed structures of martensite and polygonal ferrite in Fe-Mo-B alloys: 2) volume percent, XA, of retained austenite plus martensite aggregates in high-carbon steel; and 3) substructural differences between 100 pct bainitic ferrite structures formed at various temperatures. The quantitative relationship obtained in the first two conditions by plotting a us the known structural parameters can be expressed, respectively, as: where al, a 2 and C1, Cz are constants. In the third condition the nature of the attenuation depends on the state of dislocations generated at the transformation temperatures and also on the alloy composition. From these measured results, the mechanism of ultrasonic attenuation caused by these mixed microstructures can also be studied. MUCH interest has recently been shown in the application of ultrasonic attenuation and wave velocity measurements to the study of the microstructural characteristics of steels. The general aims of most of the investigations in this field can be grouped into two categories: one is to study the mechanisms of ultrasonic losses caused by the characteristic phases in the microstructure of steel,''' and the other is to develop nondestructive test methods and applications for quality control.~' 4 Apparently no work has been done on the evaluation of ultrasonic attenuation meas -urements as a means of quantitative determination of a given phase in the microstructure of a steel. It is well-established that the decomposition of austenite results in four main microstructural constituents—polygonal ferrite, pearlite, bainite, and martensite—and that each phase has different mechanical properties. Thus, when a steel consists of mixed microstructures, the mechanical properties can often be related to a quantitative measure of the volume percent of each phase present. This study relates ultrasonic attenuation measurements to: 1) the volume percent of polygonal ferrite in mixtures of martensite and polygonal ferrite in Fe-Mo-B alloys; 2) the substructural differences between 100 pct bainitic ferrite structures formed at various temperatures; and 3) the vol- ume percent of austenite in austenite plus martensite aggregates in a high-carbon steel. The choice of the specimen materials was based on the laboratory stocks which were suitable to produce the required mixed microstructures for this study. EXPERIMENTAL PROCEDURES Materials and Heat Treatment. Polygonal Ferrite Plus Martensite Structures. This mixture of phases was produced in a vacuum-melted Fe-Mo-B alloy. The alloy was hammer-forged at 1900" ~ to a -f-in.-sq bar. By isothermally heat treating the alloy at 1300° F for various times and then water quenching, variations in the amount of polygonal (or proeutectoid) ferrite can be controlled in a microstructure in which the balance of the material is martensite. In the present work, four different times of isothermal transformation were adopted; after heat treatment, the four specimens were machined for ultrasonic measurements. The compositions, heat treatments, and dimensions of the four specimens are listed in Table I. 100 pct Bainite Structures Formed at Different Temperatures. It has been well-established by Irvine et al.= that the presence of molybdenum and boron in ferrous alloys can retard the formation of polygonal proeutectoid ferrite and expose the bainitic transformation bay, so that a more acicular or bainitic ferrite can be obtained over a wide range of cooling rates. Their investigation6 also showed that the mechanical properties of fully bainitic steels are usually closely dependent on the substructural characteristics of the steels. For studying the substructural characteristics in completely bainitic structures, six Fe-Ni-Mo alloys, of which five were free from carbon addition and one with 0.055 pct C addition, were selected so that a wide range of hardness values for 100 pct bainitic ferrite structures could be produced by normalizing at 1900" F followed by air cooling. The different bainitic transformation temperatures were recorded during air cooling. All of the alloys were vacuum-melted and then forged at 1900" F to square bars. Data on the six specimens of these structure series are summarized in Table 11. Austenite Plus Martensite Structures. The high-carbon steel used to study austenite plus martensite structures was vacuum-melted and then forged into Q-in.-sq bar. The series of mixed structures of austenite plus martensite was produced by quenching the specimens from the austenitizing temperature to room temperature and then refrigerating them at various temperatures within the range of martensite transformation to produce different amounts of retained austenite. Data on the four specimens of this series are listed in Table 111. Quantitative Analysis of the Microstructures. The microstructures containing martensite plus polygonal ferrite were analyzed by the point-counting technique.

Jan 1, 1969

By G. Purcell, S. C. Sun

In an attempt to determine the relative collecting ability of 18-carbon fatty acids, studies were performed on rutile in aqueous solutions of the fatty acid soaps. The preceding article reported the electro-kinetic properties; this article outlines the flotation behavior. Results of these flotation experiments are described and correlated with the electrokinetic results. Recent studies of the electrokinetic1-4 and the electrochemical5,6 properties of a few solid-liquid interfaces have provided a better understanding of the flotation process. A number of investigators have attempted to determine the relative collecting ability of 18-carbon fatty acids, but their published results (even for the same mineral) vary widely. Such lack of agreement indicated a need for further investigation. In an effort, therefore, to resolve the problem, electro-kinetic studies were made on rutile in aqueous solutions of the fatty acid soaps. Following the determination of the electrokinetic properties, the flotation behavior of rutile was studied. Results of these flotation experiments are described in this paper and are correlated with the electrokinetic results. MATERIALS AND EXPERIMENTAL PROCEDURE Materials: Pure -28, + 35-mesh rutile crystals were used for all flotation tests, and nitrogen-saturated conductivity water was used throughout. Sodium hydroxide and hydrochloric acid were added for pH regulation. The methods of purification for these materials and the preparation of the soaps have been described elsewhere. 7 Equipment: A Hallimond cell, constructed in a manner similar to that described by Fuerstenau, Metzger and Seele,8 was used for the flotation of mineral particles; however, a coarse pyrex frit was substituted for the capillary. Procedure: Purified nitrogen was led through a two- way stopcock into a graduated cylinder partly filled with water. The gas forced water from the cylinder back into a header tank until the water level in the cylinder coincided with a predetermined mark. Reversal of the stopcock then allowed water in the tank to force nitrogen into the cell until the water in the graduated cylinder rose to a second predetermined mark. In this way a constant volume of nitrogen under practically constant pressure was used for each flotation test. However, the flotation time varied, depending upon the amount of mineral floated and the pH of the solution. Rutile crystals were transferred under water from a storage bottle by a glass scoop holding 1.7 g. Consistency of the scoop samples was good, varying from a low value of 1.67 to a high of 1.74 g. The water added to the conditioning bottle during mineral transfer was drained off, and then 2 cu cm of either hydrochloric acid or sodium hydroxide were added. The concentration of pH regulator was adjusted to give approximately the final soap solution pH that was required. The order of addition of reagents did not affect the results within the limits of experimental error. Soap solution of the required concentration was added under nitrogen pressure to fill the bottles completely. Conditioning for 1 hr was carried out on rolls rotating at 35 rpm. After conditioning, 2.5 cu cm of solution were run off into the container of a Beckman (model G) glass electrode pH meter. The electrodes were rinsed in this solution, which was then discarded, and 2.5 cu cm more were added for pH determination. The remaining solution and the mineral were transferred to the cell; care was taken to ensure that all mineral was washed out of the bottle by the conditioning solution. With the cell back in its flotation position the liquid just reached the desired level, and the test was started immediately. The amount of agitation in the cell was kept constant, and flotation was carried out without the use of a frother. In each series of ten tests one was run with no collector added to ensure that the mineral had not become contaminated, and two were conditioned at the same pH to check reproducibility. After each test the cell was dismounted, soaked in cleaning solution, washed in hot water and then rinsed with distilled water.

Jan 1, 1963

By C. P. Proctor

WESTERN Pennsylvania, eastern Ohio, and Illinois are carrying out experiments wherein much more slate and other impurities are loaded with the coal in the mine and hauled to the surface preparation plant for removal. In general everything is sent to the cleaning plant although there may be some gobbing in the mine. No conclusions have been announced as to the effect of such a mining system on clean coal costs. Such factors as ability of the surface plant to handle the impurities, land and facilities for disposing of the impurities, and the transportation facilities underground should be considered.

Jan 1, 1942

By FREDERICK LAISY

A NUMBER of new plants for the treatment of copper ores were completed or under construction during the year. Among these may be mentioned the plants of the International Nickel Co., those of the Hudson Bay Mining and Smelting Co. and of the Roan Antelope Copper Co. Three copper re- fineries have been constructed, one at El Paso, Tex., and the other two in Canada. Two more are projected, one in France and one in England. The International Nickel Co.'s plant consists of an 8000-ton concentrator and a smelting plant containing thirty 10-hearth Herreshoff roasting furnaces, five reverberatory furnaces, and eight Smith-Pierce converter5 . The smelting plant is estimated to have a capacity of 5000 tons of ore or concentrate per day. The roasters are superimposed on the reverbratory furnace plant. As a consequence of this arrangement, the furnace building is unusually high. being 183 ft. from yard level to highest roof elevation.

Jan 1, 1931

By J. P. Morgan, J. R. Dawson

A review of Jones & Laughlin's Vesta coal preparation plant flowsheet in 1959 indicated that, of the three sizes making up the company's metallurgical product, the -48-mesh fraction offered the greatest potential for improvement. Efforts to improve quality and yield were directed toward the use of froth flotation. After laboratory and plant tests were completed, it was decided that treatment of the entire -@-mesh fraction of the coal mix by flotation was a significant step forward in providing better coal quality and recovery. Reduction of ash in the metallurgical coal from 6.75 to 6.25% provided material savings at the coal washer, coke plant and blast furnace. The Vesta preparation plant of the Jones & Laughlin Steel Corp. is located on the Monongahela River, eight miles south of Brownsville, Pa. This plant is capable of cleaning 2400 tph of a mixture of Pittsburgh seam high volatile coals from the Vesta and Shannopin mines to produce a metallurgical coal of 6.75% ash and a steam coal containing 14% ash. Heavy media vessels are utilized to upgrade the coarse coal while launders and tables handle the -1/4-in. fraction of the raw coal feed. Cleaned -1/4-in. coal goes to boot classifiers where the 48 mesh material settles and is removed by bucket elevators. This 1/4x48 mesh material is then sent to centrifugal dryers for dewatering. As designed, the -48 mesh fraction overflows the boot as a 7 to 8% solids slurry and is recovered by cyclones and a thickener and then dewatered by filtration. The products of the heavy media circuit, the launder-table-boot-dryer circuit and the cyclone-thickener-filter circuit, are combined to constitute the shipped metallurgical coal. The Vesta-Shannopin mix is combined at Jones & Laughlin's Pittsburgh and Aliquippa Works with purchased low and medium volatile coals for the production of metallurgical coke. A review of the preparation plant flowsheet in 1959 indicated that of the three sizes making up the metallurgical product, the -48-mesh fraction, containing 16.7% ash, offered the greatest potential for improvement of coal quality. This fraction was considered low, averaging 55%, while the rejects averaged only 33% ash. It was evident that while the boot overflow fraction represented only 6% of the product mix, a reduction in ash to 6 or 7% would reduce the ash of the metallurgical coal by 0.5%. The original plant flowsheet handling the boot overflow (Fig. 1) consisted of ten 14-in. cyclones treating 70% of the overflow and producing a 48x150-mesh underflow and a -150-mesh overflow. The cyclone overflow was combined with the remaining 30% of the boot overflow to constitute the feed to a 150-ft thickener. The cyclone underflow and the 48x325-mesh thickener underflow were fed to vacuum disk filters for dewatering prior to combination with the coarse metallurgical coal. The thickener overflow stream containing the -325-mesh material was split, 40% being recycled directly to the plant water system and 60% being flocculated and clarified in an 85-ft thickener. The underflow of this thickener was pumped to waste. Efforts to improve quality and yield on the -48-mesh coal were directed toward the use of froth flotation early in the investigation. A review of the fine coal flowsheet indicated that three streams should be considered for treatment by froth flotation. These were the -325-mesh thickener overflow, the -150-mesh cyclone overflow and the -48-mesh boot overflow. Flotation of the thickener overflow was considered basically to improve recovery by upgrading the reject stream so that it could be fed to the filters along with the thickener and cyclone underflows. The overflow from the thickener contained 3.7% solids and had an ash analysis of 33%. Flotation of the cyclone overflow and boot overflow were considered to upgrade coal quality as well as yield. Treatment of the cyclone overflow, a 5.4% solids slurry averaging 27% ash, would eliminate the coal thickener and provide a feed of flotation concentrate and cyclone underflow to the filters. Treatment of the boot overflow would eliminate both the cyclones and thickener and feed only flotation concentrates to the filters. Flotation feed in this

Jan 1, 1962

By L. E. Young

The purpose of this paper is to start a discussion on: (I) methods of supporting the immediate roof, particularly of local areas of poor roof, during the mechanical loading of coal; (2) methods of increasing the rapidity of the movement of the mining faces so that, without the use of cribs, jacks, park walls, and filling, there will be no danger to men, equipment, and working places from the subsidence of the overlying strata. In the Pittsburgh district the application of mechanical loading devices in mines working in the Pittsburgh seam has been retarded by the difficulties of holding and handling the draw slate. Normally the thickness of this slate averages about 8 in. but the hardness varies, and a cut of coal cannot always be loaded without placing posts or crossbars to support the slate. Locally, the slate may be thicker and special methods of support may be required. If crossbars are placed to hold the slate when the coal averages 5 ft. in thickness, the standard methods of transporting the coal cannot be followed, and the use of conveyors may be desirable. Very little information is available on the effect of increasing the rate of movement of advancing or retreating break lines or longwall faces. A few British publications have presented some data but all such data relate to longwall faces that have moved not more than 6 ft. a day. The most rapid rate of movemerit of longwall faces in Germany is 6 ft. per day. In the ordinary hand-loading mine in western Pennsylvania break lines on full retreat will move about 2 ft. per day. If loading machines are used under similar conditions the rate of retreat may reach 4 ft. per day. In a mine where coal is loaded by hand on conveyors three shifts per day, the rate of retreat has ranged from 11 to 16 ft. per day, with an average of 13 ft. If mobile loading machines could be used to load on conveyors on break lines, the rate of retreat should be increased substantially During 1935 and 1936, the United States Bureau of Mines, under a cooperative agreement with the Pittsburgh Coal Co., carried on studies of roof movement at Montour To. 10 mine. The work war done urider the direction of Mr. H. P. Greenwald, Supervising En neer, Experi-

Jan 1, 1938

By L. E. Young

The purpose of this paper is to start a discussion on: (I) methods of supporting the immediate roof, particularly of local areas of poor roof, during the mechanical loading of coal; (2) methods of increasing the rapidity of the movement of the mining faces so that, without the use of cribs, jacks, park walls, and filling, there will be no danger to men, equipment, and working places from the subsidence of the overlying strata. In the Pittsburgh district the application of mechanical loading devices in mines working in the Pittsburgh seam has been retarded by the difficulties of holding and handling the draw slate. Normally the thickness of this slate averages about 8 in. but the hardness varies, and a cut of coal cannot always be loaded without placing posts or crossbars to support the slate. Locally, the slate may be thicker and special methods of support may be required. If crossbars are placed to hold the slate when the coal averages 5 ft. in thickness, the standard methods of transporting the coal cannot be followed, and the use of conveyors may be desirable. Very little information is available on the effect of increasing the rate of movement of advancing or retreating break lines or longwall faces. A few British publications have presented some data but all such data relate to longwall faces that have moved not more than 6 ft. a day. The most rapid rate of movemerit of longwall faces in Germany is 6 ft. per day. In the ordinary hand-loading mine in western Pennsylvania break lines on full retreat will move about 2 ft. per day. If loading machines are used under similar conditions the rate of retreat may reach 4 ft. per day. In a mine where coal is loaded by hand on conveyors three shifts per day, the rate of retreat has ranged from 11 to 16 ft. per day, with an average of 13 ft. If mobile loading machines could be used to load on conveyors on break lines, the rate of retreat should be increased substantially During 1935 and 1936, the United States Bureau of Mines, under a cooperative agreement with the Pittsburgh Coal Co., carried on studies of roof movement at Montour To. 10 mine. The work war done urider the direction of Mr. H. P. Greenwald, Supervising En neer, Experi-

Jan 1, 1938

By P. C. Johnson, B. A. Stein

This paper describes a study of the effects of combined heat treatment and explosive loading on the mechanical properties of high-strength steels. nis program investigated two distinct areas: 1) the effect of shock waves, without gross irreversible defmmution, on a 3-Cr steel at various stages of heat treatment; and 2) the effect of rapid deformation (explosive forming) on H-11 and D6-AC steels in the metastable austenitic state. The mechanical properties of these steels were improved, in some cases markedly, as a result of these treatments. ,AUSFORMWG, which requires the plastic deformation of metastable austenite, is a process which can appreciably improve the properties of selected alloy stee1s.l,2 The Ausform process significantly increases the strength of these steels without decreasing their ductility. The properties at high temperatures are also improved through a change in the response of the steels to tempering. Although the mechanism by which ausforming alters the properties of these steels is not fully understood, it appears that the dislocation arrays produced by deformation of the metastable austenite influence the structure of the martensite on subsequent transformation. This, in turn, affects the strength, ductility, and tempering response of the martensite. This research used chemical explosives to deform steels at various stages in their heat treatment in order to improve the properties of these steels. The explosive energy is used in two ways; 1) high-pressure shock waves are propagated through the steel to produce extensive microscopic shear strain without causing a large irreversible change in shape, and 2) explosive energy is used to cause extensive macroscopic plastic strain in the metastable austenitic state (explosive forming). I) AUSFORMING WITH INTENSE SHOCK WAVES The steel used in this phase of the research was an alloy having a nominal composition 0.43 pct C, 3.0 pct Cr, 1.5 pct Ni, and 1.5 pct Si. The steel was subjected to intense shock waves in three conditions: 1) in the metastable austenitic state, 2) in the tempered mar tens itic state, and 3) in the tempered martensitic state after ausforming by conventional techniques. The specimens were in the form of disks 2.75 in. in diam and 5/16 in. thick. These were incorporated into a specimen assembly consisting of two disks pressed into a 5 by 5 by 1 in. block of stainless steel, Fig. 1. Spalling (or scabbing) is confined to the front disk. The specimen is protected from oxidation and decarburization by the surrounding metal. The temperature of the assembly is monitored by a thermocouple inserted into one side of the stainless steel block. The assembly is positioned over an oil reservoir which serves both as a means of catching the disks and as quenching medium for the disks shocked under ausforming conditions. Plane shock waves are introduced into the assembly by a metal driver plate impacting the top surface of the block. The driver plate is accelerated by a chemical explosive sheet supplied by E. I. du Pont de Nemours & Co. All the specimens were subjected to plane shock waves having a peak pressure of approximately 430 kbar. The pressure is that quoted by G. E. Dieter for the plane wave generator used in this work.' The driver plate used was 1/4 in. thick, so that the initial pulse was essentially a l/2-in.-wide square wave. The attenuation of the peak pressure during the subsequent 1/4 in. is estimated to be less than 5 pct. The shock front induces a temperature rise, a portion of which is irreversible. Rough estimates (+25 pct) of this temperature rise have been made for iron shocked at room temperature.4 For a 500-kbar shock wave, the temperature rise in the shock front is about 700°F, and is held for a time of the order of microseconds. The irreversible temperature rise, which remains after the shock wave passes, is about 450°F.4 The disks are quenched to room temperature within a few seconds of the shock treatment. It should be emphasized that the temperature rises given above are estimates for pure iron at room temperature, and are not necessarily true for the tests made in this work. The disks shocked at temperatures in the metastable austenitic range were austenitized in the stainless steel assembly in a furnace protected from the firing area. The assembly was removed from the furnace and placed over the recovery reservoir. The plane wave generator was then positioned and

Jan 1, 1963

By Joseph T. Roy

MINING revival during the last few years has brought about a considerable increase in the number of gold and silver determinations made, noticeable in all branches of the industry but especially so in the business of a custom smelter. At East Helena, solely a custom smelter the assay department found that the four assay furnaces available were inadequate to handle the increased amount of work. These furnaces were of a standard design, having duplex muffles, one superimposed on the other; each muffle was 12 1/2 in. wide, 18 1/4 in. long and 6 in. high, and could handle 72 cupels or 20 fusions. Since the heat varied considerably between the upper and lower muffles, cupellations were not ruin in both at the same time. To speed up assaying, E. A. Meale, chief chemist, had the happy idea of enlarging a muffle furnace, originally designed by the Montana Power Co., so that one muffle would acconmmodate at least as many determinations as the duplex muffles. An order was given to the Denver Fire Clay Co. for a Carbofrax muffle of the size required and the local engineering department enlarged the furnace to accommodate the muffle. Details of the

Jan 1, 1938

By M. F. Goudge

LIMESTONE surpasses any other rock or mineral in the number and diversity of its uses and in the quantity consumed fur industrial purposes. Either in the raw state or when calcined to lime it enters directly or indirectly into the manufacture of a great variety of products and its sphere of usefulness is continually expanding. The term "limestone" as here employed includes all varieties from high-calcium limestone, consisting almost entirely of the mineral calcite, to the highly magnesian variety, largely dolomite. Lime is also discussed .because lime is simply calcined limestone and often the material may be used in either the calcined or natural state. Limestone has been of service to man since prehistoric times but only in the last hundred years has it become one of the most important raw materials in industry. In every industrial country it comprises the greater part of the total stone produc-

Jan 1, 1937

By Frederic Benard

THE treatment of Balbach-Thum slimes at Copper Cliff by the Ontario Refining. Co. is of interest because it differs considerably from methods usually employed for the recovery of fine gold from parting-plant slimes. Owing to the comparatively high percentages of pal-ladium and platinum, wet methods are used to remove the greater proportion f these metals before electrolytic refining in the Wohlwill cells. THE PLANT The platinum-metals department, Wohlwill room, and gold-melting room extend along the north side f the silver refinery and are separated from the parting plant by a glass partition (Figs. 1 and 2). The platinum-metals department resembles a laboratory built on a large scale, with the various pieces of equipment laid out on terraces to facilitate handling. Because of the corrosive nature of the solutions, chemical stoneware is used throughout. Elevation of acids is accom-plished by means of Mariotte bottles. On the top level are three steam-jacketed stoneware kettles of 50-gal. capacity, also a packed tower. One kettle is used for digesting the slimes while the remaining kettles are used for precipitating the gold. The dissolver is equipped with a treated concrete hood, which is connected to the flue system. Gases are drawn off through the packed tower by means of a 6-in. stoneware exhaust fan. A 15 per cent solution of sodium carbonate is continually circulated through the tower. On the intermediate level are two suction filters, one for removing silver chloride and the other for the gold sand. The filter medium consists of an asbestos pad covered with a filter paper on which is a layer of twill.

Jan 1, 1938

By AIME AIME

BESIDES commanding increasing importance as an alloying element in combination with ferrous and other nonferrous metals, the variety of uses for pure nickel continues to widen. For coinage it is growing in popularity. These coins have been minted for 27 countries in 72 issues representing 69 denominations. Approximately 3,000,000,000 pieces have been struck, the aggregate weight, of which amounts to nearly 14,000 tons. . Danzig, Iraq and Japan are the most recent governments to adopt, pure nickel coinage. France is adding the denomination of five francs to its other nickel currency; they replace silver pieces. Germany is now minting a new issue of one Reichsmark coins of pure nickel. The Japanese program for 1933 called for the issue of 35,000,000 10-sen pieces and 30,000,000 5-sen pieces. In radio tube manufacture the consumption of pure nickel was approximately twice that of 1932. During 1.933 the nickel plating process by which bright deposits may be plated

Jan 1, 1934

By Geoffrey Purcell

For anyone contemplating flotation research with only a very limited amount of mineral available for testing, the choice of suitable experimental equipment is by no means obvious. Hallimond's original and delightfully simple cell1 has been modified by subsequent investigators2to give quantitative and reproducible results on small samples. However, the modifications have necessarily compromised its simplicity, and the services of a skilled glass blower are required to duplicate the cell. Vacuum flotation tests3 at best qualitative and may, under certain conditions4, be quite impracticable. A hundred years ago, Thoreau observed that "our life is frittered away by detail," and his advice was to "simplify, simplify," The success of the simple cell described below, which was developed by the author and differs somewhat from Hallimond's original, suggests that Thoreau's advice still has merit a century later. CELL CONSTRUCTION The cell [Fig. 1 (a) and 1 (b)] consists essentially of a 25-ml pipet from which has been cut the con- stricted top. The length cut off is not critical since this merely determines the final volume of the cell. Cell volume may be varied in this way from 20 to 50 cc. A pyrex extension tube, equal in diameter and approximately half the length of the cut pipet, is attached to the top of the pipet by means of 2 ½ in. of close-fitting tygon tubing. When assembled, the two pyrex tubes should be spaced about ½ in. apart. Another length of tygon tubing is added to the extension piece for sealing purposes. A ¾ -in. disc of porous material (teflon cloth is ideal), secured in place over the pipet tip with another piece of shaped tygon tubing, completes the cell assembly. Tygon tubing may be shaped by pushing it over the pipet tip or some similar form and heating carefully over a low flame. For flotation [Fig. 1 (c) 1, the pyrex extension tube is rotated approximately 70º from the vertical and held in position by a wire hook and eye. Floated material, after reaching the free surface, falls and rests on this inclined plane. The barrier formed by the bent tygon tubing ensures that floated material does not slide back and return to the vertical portion of the cell.

Jan 11, 1965

By E. H. Bunce, E. C. Handwerk

The inherent difficulties of zinc smelting arise from the fact that metallic zinc is volatilized at the reducing temperature of zinc oxide and thus is liberated in the form of a vapor. This vapor must be subsequently condensed to obtain metallic zinc, first in molten and eventually in solid form. Zinc vapor is sensitive to oxidation not only by air but by combustion gases containing carbon dioxide. It is, therefore, necessary to carry out both the reduction and the condensation operations in a closed system consisting of an externally heated muffle with attached condenser from which extcrnal oxidizing agencies are excluded. However, the reoxidation of zinc vapor cannot be entirely prevented by excluding external sources of oxidation. Internal sources of oxidation are necessarily present when oxidic zinc ores are reduced by a carbonaceous reducing agent. The reduction reactions themselves involve, first, the production of carbon monoxide in an amount at least equal in volume to the zinc vapor produced in the reaction, and, second, the formation of carbon dioxide. Not all of the carbon dioxide is reduced again to carbon monoxide by the excess carbon in the time available, and the slightly oxidizing condition, which results, seriously affects the efficiency of the condensation of the zinc vapor to the metallic state. In the past the difficulties arising from these causes have limited practical zinc smelting on an industrial scale to the use of small retorts equipped with small condensers. The retorts had to be small, because a closed refractory container capable of excluding oxidizing gases from the heating chamber surrounding the retort could not be built in large dimensions. The size was also limited because ordinary refractories when thin enough to conduct heat readily are not capable of sustaining a heavy load of charge at high temperature. Moreover, a loose charge of zinc ore and carbonaceous reducing material such as fine anthracite coal or coke breeze is a poor conductor of heat, thus limiting the cross section of the retort. The operation of these small retorts requires arduous

Jan 1, 1937

By AIME AIME

HONORARY COMMITTEE. HON. C. D. WALCOTT (Chairman.), Director U. S. Geological Surrey. HON. FREDERICK I. ALLEN, Commissioner of Patents. DR. FRANK BAKER, Superintendent National Zoological Park. MR. CHARLES A. BELL, President American Security and Trust Co. MAJOR JOHN BIDDLE, Engineer Commissioner of District of Columbia. ADMIRAL C. M. CHESTER, Superintendent U.S. Naval Observatory. GENERAL WILLIAM CROZIER, Chief of Ordnance, U. S. A. ADMIRAL GEORGE DEWEY, Admiral of the Navy. COLONEL CLARENCE R. EDWARDS, Chief Bureau. of Insular Affairs. MR. WILLIAM C. FOX, Director Bureau of American Republics. MR. CHARLES C. GLOVER, President The Riggs National Bank. GENERAL A. W. GREELY, Chief Signal Officer, U. S. A. MR. BERNARD R. GREEN, Superintendent Library Building. GEN. G. H. HARRIES, Vice-President Washington Electric Railway Co. HON. E. A. HITCHCOCK, Secretary of the Interior. COMMANDER H. M. HODGES, Chief Hydrographer, U. S. N. PROF. W. H. HOLMES, Chief Bureau of American. Ethnology. PROF. S. P. LANGLEY, Secretary Smithsonian Institution. GENERAL ALEXANDER MACKENZIE, Chief of Engineers, U. S. A. ADMIRAL N. E. MASON, Chief Bureau of Ordnance, U. S. HON. WM. M. MEREDITH, Director Bureau of Engraving and Printing. HON. V. H. METCALF, Secretary Department of Commerce and Labor. HON. WILLIS L. MOORE, Chief -U. S. Weather Bureau. HON. PAUL MORTON, Secretary of the Navy. MR. F. H. NEWELL, Chief Reclamation Service, U. S. Geological Survey. HON. S. N. D. NORTH, Director Census Office. CAPT. E. C. PENDLETON, Superintendent Naval Gun Factory. MR. GIFFORD PINCHOT, Chief Forester, Department of Agriculture. MR. HERBERT PUTNAM, Librarian of Congress. ADMIRAL CHAS. W. RAE, Chief Bureau of Steam Engineering, U. S. A: MR. RICHARD RATHBUN, Assistant Secretary Smithsonian. Institution. HON. W. T. RICHARDS, Commissioner General Land Office.

Jul 1, 1905