Search Documents

By H. W. Peirce

Identified and utilized Arizona salt deposits are of two ages: 1) Permian in the Colorado Plateau, and 2) Tertiary in the Basin and Range country. Uses include: a) storage of energy fluids in man-made solution cavities in both Permian (Supai Formation) and Tertiary (Luke salt body) salt and b) production of marketable products by solution and evaporation of tertiary salt. The two liquid petroleum storage Projects have a combined storage capacity in excess of 380 million L (100 million gal). Current production of salt products approximates 32 kt/a (32,000 stpy). Increasing demand for both storage and salt products is anticipated.

Jan 1, 1983

By M. P. Nackowski, Armond H. Beers, W. T. Parry

Three hundred soil samples were collected on a one-mile grid in a 400-square mile area of the Oquirrh Mountains, Utah, including the Bingham-Lark, Ophir, Rush Valley, and Mercur mining districts. The soil samples were analyzed for copper, lead, zinc, silver, molybdenum, manganese, and iron by X-ray fluorescence using arsenic as an internal standard. Anomalies coincide in most cases with the mining districts. However, in the Mercur district no anomalies were detected. Also samples collected one mile from the Bingham mine barely reflect this major producer. No samples were collected within the Bingham mine area.

Jan 1, 1973

By Roshan B. Bhappu, George M. Potter

The chemistry involved in the recovery of gold and silver from natural resources through hydrometallurgical and pyrometallurgical processes is reviewed. Process metallurgy for the cyanidation, activated carbon adsorption, carbon stripping, and electrowinning of gold and silver is discussed. The application of zinc sodium sulfide use for silver recovery from cyanide solutions is covered. Electrooxidation, other oxidation methods and roasting processes for problem ores and concentrates containing organic carbon and impurities such as arsenic, antimony, and tellurides are summarized. The smelting of cathodes, precipitates, and other products, and the various wet and furnace steps in separating dore metal are also reviewed.

Jan 1, 1981

BROWN iron ore reserves of Franklin county are being proved economical by Heavy-Media separation at the Blackburn mine of the Shook & Fletcher Supply Co. about 120 miles north-west of Birmingham. The ore occurs under a cover of ferruginous chert and gravel and these materials are also disclosed as streaks in the ore body as it is mined. Previous methods of jigging and hand sorting the ore became too expensive because of rising wages but the use of Heavy-Media separation has proved economical and is making Franklin county the most promising source of additional reserves of brown ore.

Jan 12, 1950

By M. Cross

The main results from a programme of theoretical work on various aspects of the pelletizing operation are presented. This paper is primarily concerned with the modelling of: (i) The balling drum operation. A model is outlined which clearly demonstrates the characteristic surging behaviour of the balling circuit. It is used first in a control analysis and, subsequently, in the design and testing of various control schemes. (ii)The grate-kiln-cooler induration process. Models describing each of the constituent processes are outlined and a composite model of the whole induration process presented. The main results from each of these models are discussed.

Jan 1, 1977

By J. H. Allen

The air lift method of pumping water is discussed. A review of several large diameter hole drilling projects that used reverse- circulation air-lift techniques is presented. Proposals are made for reverse circulation flow rates for slow rates of bit penetration (5 fph) as well as reverse-circulation flow rates for faster rates of bit penetration (10 fph). The Ingersoll-Rand air lift equations are modified for rotary drilling operations. By establishing minimum reverse circulation flow rates and utilizing the modified air lift equations, the establishment of minimum circulation equipment sizes and a more definitive requirement for improved bit body design should result.

Jan 1, 1978

By R. Haynes

ON the basis of compositional changes of a phase observed in a eutectoid Cu-Al alloy1 it has been suggested that mechanisms for the decomposition of the ß phase proposed by earlier workers2-5 were incorrect. These data are reinterpreted in conjunction with lattice parameter data obtained on an alloy containing 12.2 pet Al, whose isothermal transformations have been reported elsewhere.5 The a Lattice Parameters of a 12.2 Pet A1-Cu Alloy—~iffraction patterns of completely transformed specimens were obtained in a back reflection camera using copper Ka radiation. Lattice parameters of

Jan 1, 1959

Shooting Soot from Stacks In the DuPont magazine of June, 1916, S. R. Russell describes a method of cleaning large smoke or kiln stacks which he calls "simple,. economical- slid-most efficient" and-which- he -says can- be used in either-lined or unlined stacks, brick or steel, without fear of injury to the stack or lining. He gives the following specific directions: "The gun can be made out of air old piece of shafting about 4 in. in diameter and 14 to 16 in. long. Bore a hole 1 ¾ in. in diameter and 10 in. long in the center of the piece. Then bore a small horizontal hole ¼ in. in diameter through the piece-to the bottom of the center bore. This hole serves as a touch hole for inserting the fuse. "The-whole thing can be mounted on a pedestal about 6 in. in diameter so that it will stand in an upright position. "The -method of operation is as follows: Pour some FFF Blasting Powder into the mouth of the cannon to about 2 in. from the top. Tamp to the collar with dry clay. , A short piece of fuse is inserted in the touch hole and in contact with the main powder charge. Open the flue door at the bottom of the stack, set the cannon on the bottom and in the center of the stack, light the fuse and close the flue door. "The explosion shakes and loosens the soot adhering to the sides, causing it to fall to the bottom. It can' then be removed through the flue opening.

Jan 9, 1916

By T. F. Witherbee

AS the forms of blown-out furnaces are of much interest to ironmasters and metallurgists, the manner of taking the accompanying sections of the Cedar Point stack is here given. The diagrams show the original and also the final shape of the furnace after a two years and twelve days' blast,, during which the following solid materials passed through it, viz.: Coal, 41,000 tons; ore, 57,000 tons; limestone, 30,000; total, 125,000 gross tons. Product, 411/4 tons per day Bessemer pig iron. The apparatus used in taking the sections was a modification of that proposed by Mr. Frank Firmstone,* and consisted of a sliding rule, to follow around the circumference of the stack, which rule was connected by a string to a segment of a circle of 24 inches radius. The segment was carried by an arm which connected it to a huh as a centre, 2 inches in diameter. A second string was wound around the hub, and communicated motion to a pencil-carrier, the pencil of which marked out on paper the exact outline, and reduced it to a scale of & inch to the foot. The whole machine was made in about three hours, with the facilities of a carpenter's shop, and gave in operation every irregularity of the lining. The sections were taken at salient points, by lowering a hanging staging on which the apparatus was placed. Tracings from the paper of the machine were made, and, as in this case several copies were required, the tracings were glued on to thin sheets of basswood, and patterns carefully sawed out with a bracket saw.

Jan 1, 1879

INTRODUCTION TO COMPOSITING Individual drill hole samples may vary greatly in size, length, and weight. The sample interval may represent any convenient unit of hole length, and is usually related to the type of drill being used to obtain the sample. Depending upon the type of mineral deposit, it is desirable to group the individual sample values into composite weighted values representative of some particular zone or volume of the ore body. For example, values of several sequential samples of diamond drill core 3 m (10 ft) in length may be grouped together to represent a 12-m (40-ft) sample value over one bench height. On the other hand, several individual sample values taken across the thickness of a stratiform deposit or a vein zone may be weighted together to represent the value of the total thickness at the point of intersection. The choice of composite intervals is usually dictated by the type of mineral deposit and the mining method selected to produce the mineral. The techniques of weighting values from various lengths of samples into a composite value has already been discussed briefly in Chapter 3. Further examples of determining weighted composite values will be given in the following discussion on compositing for various types of mineral deposits. SAMPLE VALUE COMPOSITES AND TYPES OF MINERAL DEPOSITS There are many kinds of mineral deposits, each of which will require special treatment of sample data to obtain the best composite intervals for evaluating the deposit. It cannot always be known before hand what the optimum composite interval will be. Such composite intervals may properly be determined by geologic factors that are often unknown prior [ ]

Jan 1, 1980

By Carl E. Reistle

ENGINEERS as a group are often criticized because they have been responsible for the development of many technical improvements only to allow the administration of them to pass into the hands of others who may have little understanding of how they operate and little competence in their use. These criticisms are not always justified. There are many engineers who have shown themselves to be great administrators in addition to being great creators or builders, and more and more one sees the engineer demonstrating unusual administrative ability as he moves into the executive ranks. The last five or ten years have seen a new movement developing in this country-a movement brought about through the recognition by business statesmen that successful business administrators and executives just cannot be expected to develop like Topsy, that the management of a company must deliberately take steps to cultivate the proper climate or environment for growth if it wishes to provide an adequate and capable succession of executives in the future. This movement has taken on a number of names-Management Development, Executive Development, Personnel Development-but are these not actually misnomers? Can we develop anybody? In the strictest sense of the word, the author doubts that anyone can change any other person, at least, not much. The change must come from within. Perhaps this movement should be looked at not as a program of developing people but as one of giving people an opportunity to develop themselves. In the Humble Oil & Refining Co. there is an Executive Development Program; maybe it might better be called a Program of Development for Executives.

Jan 8, 1954

By Heinrich Ries

In another place,* the writer has called attention to the modern methods of the laboratory investigation of clay, and it is desired here simply to discuss one branch of the subject, which, though of considerable importance, has heretofore received little attention in this country, viz., the rational analysis of clay. In order, however, the better to point out the bearings and advantages of this procedure, it is necessary to refer briefly to the ultimate analysis as well. The remarks in this paper refer only to the use of clay for the manufacture of clay-products. Pure clay or kaolin-f is extremely refractory, possesses little plasticity, and usually shrinks aud warps considerably in burning. Even the smallest proportion of impurities changes these properties, so that the kaolin exhibits variations in shrinkage, plasticity, tensile strength, fusibility, and often color when burned. The majority of nearly pure kaolins consist of kaolinite (A1,O2 2SiO,, 2H20), undecomposed feldspar, and quartz. The kaolinite generally forms the finest particles of the clay and is known as the clay-substance, while the rest of the clay-particles are collectively spoken of as sand. In the ordinary or ultimate analysis, the substances generally determined are silica, alumina, ferric oxide, lime, magnesia, alkalies and water. An analysis of this type simply regards the clay as a mixture of elements or oxides, but gives no clue as to the actual condition in which these substances exist, i.e., whether as silicates, oxides or carbonates, etc., a point which it is of the highest importance to know; for the individual components of the clay influence its properties not only according

Jan 1, 1899

By Anthony Sharkey

Introduction In Europe, longwall mining accounts for over 95% of coal produced from deep mines, whereas in the U.S.A., longwall accounts for less than 5% of deep mine coal production. There are many reasons for the difference, but in general: a. U.S. mine operators have invested heavily in continuous mining or conventional equipment which continues to produce acceptable results; b. There 1s a reluctance to change from, a familiar (and proven) mining method to an unfamiliar one, despite promises of huge production increases,; c. Multi-seam mining in Europe has made longwall the only really viable mining method, whereas In the U.S.A. multi-seam mining (particularly in "below-drainage" mines), is relatively rare; d. Although some spectacular results have been achieved by longwall in the U.S.A.(I), the general performance of longwall in this country has not been good enough to generate much enthusiasm for its wide application; e. The much higher level of investment in face equipment required for longwall when compared to alternative methods (approximately $7.5 million for a medium seam longwall installation and $1 million to $1.5 million for a continuous miner section). However, declining productivity, national energy requirements and safety legislation are creating a situation in which longwall as a viable mining method is being examined more closely and in more places than hitherto. This paper, therefore, attempts to identify some of the principal criteria needing examination in any assessment of the feasibility of longwall application, the limitations of information for those criteria in the decision making process and the need for further research and development to assist the mine operators make the decisions.

Jan 1, 1981

By F. W. Osterwald, C. R. Dunrud

A continuously recording seismic network was constructed in 1962 by the U.S. Geological Survey to locate epicenters and record incidence of bumps (bounces, rock bursts) that occur in the bituminous coal mines of the Book Cliffs coal field near Sunny-side, Utah. The coal is mined because of its value as coking coal, although these bumps may be a hazard to life and property. Daily records of tremors caused by bumps for 1 3/4 years indicate that a seasonal pattern, as well as a daily pattern, exists for the number of bumps that occur in a given period. Maxima occur in May and June and November and December. Marked increases at 5-day to 9-day intervals are superimposed on these seasonal maxima. The largest bumps commonly occur during seasonal maxima when the rate of occurrence suddenly decreases and the amplitude of the individual bumps increases. Knowledge of this pattern may lead to prediction of general locations and periods of increased hazard from bumps. Experience to date has shown that prediction of precise times and locations of hazardous bumps is not possible, and may never be; primarily because even a small bump can be a hazard to life and property. Some bumps or bump sequences are actually composites, consisting or two or more discrete bumps a few tenths of a second to a few seconds apart. Violent and spontaneous releases of coal and rock from faces, ribs and roofs of mines (termed bumps or bounces by miners) are a common hazard to life and property in the coal mines located in the Book Cliffs near Sunnyside, Utah (Fig. 1). These bumps

Jan 1, 1965

By R. L. Templin

IN TREATING a cast metal by any working process such as rolling, drawing or forging, variations in the conditions present in the remelting, casting, chilling and preheating of the initial ingot will certainly have some effect on the physical properties of the final product. In considering the effects of cold working on the physical properties of metals, however, it will be assumed that these factors, being controlled according to best practice, will remain constant and therefore may be neglected. Starting with such a uniform metal ingot, the next operation in the production of wrought metal involves hot working by rolling, forging or extrusion so as to produce a slab, billet or bloom. This working must be sufficient to produce substantial grain refinement and minimize any defects occurring in the initial ingot. Even such a hot-worked product is not suitable as a starting material for determining the effects of cold working because it contains internal strains analogous to those resulting from cold working. It is necessary, therefore, to supplement the hot working with a considerable amount of cold working, followed by a proper annealing in order to obtain a material suitable for use in defining the effects of cold working on the physical properties of a metal. That is, if the effects of cold working are to be evaluated accurately it is necessary to have other effects at least constant if not absent. Such material, unfortunately, cannot always be obtained in commercial practice but the requirements just indicated certainly represent the desired goal; this goal has been attained in the treatment of some metals, one being aluminum.

Jan 1, 1929

By H. F. Yancey, M. R. Greer

At the annual meeting of this Institute held two years ago a new method1 of estimating the grindability of coal was described, based on experimental work carried on by the Bureau of Mines at its Northwest Experiment Station. Since that time, several organizations concerned with the testing or utilization of coal as pulverized fuel have adopted and used the method in determining the grindability of several hundred samples of coal. In addition, a series of comparative tests of this method and three others has been carried out in five laboratories under the auspices of Committee D-5 of the American Society for Testing Materials. As a result the Committee has recommended that the Bureau of Mines method, designated as the "ball-mill method," and the Hardgrove method2, previously advanced, be accepted as tentative standards3. Since the ball-mill method was originally developed and published, an opportunity has been presented to apply it to a larger number of coals and to study intensively some of the principles upon which the method is based. This paper presents a résumé of these further studies and includes a comparison with the Hardgrove-machine method. Trial runs were also made with another procedure recently proposed—the C.I.T. roll-test method4. Principles of Methods In the ball-mill method, the relative amounts of energy necessary to grind coals to the same fineness are determined by the number of revolutions of the mill required to reduce 80 per cent of the feed (500 grams of 10 to 200-mesh coal) fine enough to pass a 200-mesh screen. This is a

Jan 1, 1936

By H. F. Yancey, M. R. Greer

At the annual meeting of this Institute held two years ago a new method1 of estimating the grindability of coal was described, based on experimental work carried on by the Bureau of Mines at its Northwest Experiment Station. Since that time, several organizations concerned with the testing or utilization of coal as pulverized fuel have adopted and used the method in determining the grindability of several hundred samples of coal. In addition, a series of comparative tests of this method and three others has been carried out in five laboratories under the auspices of Committee D-5 of the American Society for Testing Materials. As a result the Committee has recommended that the Bureau of Mines method, designated as the "ball-mill method," and the Hardgrove method2, previously advanced, be accepted as tentative standards3. Since the ball-mill method was originally developed and published, an opportunity has been presented to apply it to a larger number of coals and to study intensively some of the principles upon which the method is based. This paper presents a résumé of these further studies and includes a comparison with the Hardgrove-machine method. Trial runs were also made with another procedure recently proposed—the C.I.T. roll-test method4. Principles of Methods In the ball-mill method, the relative amounts of energy necessary to grind coals to the same fineness are determined by the number of revolutions of the mill required to reduce 80 per cent of the feed (500 grams of 10 to 200-mesh coal) fine enough to pass a 200-mesh screen. This is a

Jan 1, 1936

G. R. GOHN. l-1n Table I11 of The Sager, Brown, and Mears paper, which was presented on the screen, data were given showing the results of accelerated corrosion tests of certain magnesium alloys. Mention was made that these were carried to a certain time which was used as a measure of failure but no mention was made as to the period of time. I would like enlightenment on that. G. F. SAGER (Author).-In reply to Mr. Gohn's question regarding the times of exposure for the accelerated stress-corrosion tests referred to in Table I11 of our paper, which shows the correlation between accelerated and atmospheric stress-corrosion tests on magnesium alloys, I can say that we usually run the accelerated tests on such alloys for at least 500 hr. We feel that this is long enough to reveal any marked susceptibility to stress-corrosion cracking. In the case of the atmospheric tests on such alloys, we have not yet decided how long we should expose the specimens. Most of them are being exposed for indefinite periods and a good many of our specimens have now been exposed for several years. We may want to continue some of the tests for five or ten years. The period of six months mentioned in connection with the times of exposure for the atmospheric specimens was a rather arbitrarily selected minimum time for which specimens had to be exposed before we counted them with those that had not failed. A fairly large number of magnesium- alloy specimens have been exposed in the atmospheric stress-corrosion tests at var-

Jan 1, 1945

By Louis D. Huntoon

After the completion, in 1905, of the Hammond Mining and Metallurgical Laboratory of the Sheffield Scientific School, Yale University, it became necessary to secure and assay a large assortment of ore-samples, and to arrange the results in such a manner as to admit of use with the least amount of work on the part of the instructor. At first, pulp-samples, together with their respective assays, were secured from the mines, smelters, and public aesayers, but this practice did not prove satisfactory. It was not only difficult to secure a suffciently large supply of material, but it was also impossible to secure the proper assortment required for instructing students. It involved considerable work for the donors to select the samples and furnish a record of the assays, and also for the instructors to examine each pulp and determine its character. Some of the samples did not contain a sufficient quantity of pulp for the student to check his work in case his first assay did not correspond to the record. In order to increase the number of samples and to vary the character of the material, pulp-samples were later mixed with barren rock and with sulphides, but this method also was unsatisfactory and has been discontinued. At present, small lots of ore are secured by gift or purchase from engineers, public assayers, and the managers of mines, mills, and smelters. These lots weigh from 10 to 100 lb. each, and are rarely finer than 0.25 in. in size. The larger samples permit of a careful study by the instructor in order to determine the best method of assaying to be followed. In universities in which assaying is taught the record of the samples should fulfill the following requirements:

Jan 1, 1910

By E. Maxwell, C. J. Bechtoldt, H. C. Vacher

IN the course of an investigation of the properties of metals at low temperature there was occasion to determine the constitution of four iridium-osmium alloys. There is very little information in the literature1 on the constitution of synthetic Ir-0s alloys. Zvyagintzev' s has made a comprehensive study of different natural Ir-0s alloys and concludes that alloys containing more than 32 pct 0s have the close-packed hexagonal structure of osmium, whereas those containing less than 32 pct 0s have the face-centered cubic structure of iridium. The alloys studied in this work were prepared by the American Platinum Works, Newark, N. J., and were received in the form of fragments approximately 1.5 mm average diameter. The fragments had been obtained by crushing ingots made by fusing charges of iridium and osmium under an arc and air cooling. The ingots were not given a homogenizing heat treatment. Sample fragments Table I. Results of X-Roy Diffraction and Microscopic Examinations Phases Present as Determined by X-ray Diffraction Osmium Alloy Close- Iridium Face- Packed Centered Osmium, Iridium, Hexagonal Cubic Mlcro- WtPot Wt Pct Structure Structure scope 0 99.9 None Present 1 23.6 76.4 None Present 1 38.7 61.3 Present Present 2 59.4 40.6 Present Present 2 79.0 21.0 Present Not detected 2 99.9 0 Present None 1 Note: Chemical analyses of the iridium, osmium, and alloys were furnished by the American Platinum Works. of the iridium and osmium used in making the alloys also were included. Several fragments of each metal and alloy were examined microscopically and by X-ray diffraction. For the X-ray method the fragments were crushed further to pass a 270-mesh screen, then sealed in evacuated fused-silica tubes, heated to 1100°C for 18 hr, and allowed to cool in the furnace. Powder X-ray diffraction patterns were obtained from the annealed fragments by means of a Norelco camera having a diameter of 114 mm, and unfiltered cobaIt radiation. For the microscopic examination several fragments in the as-received condition were mounted in Melmac, (American Cyanamid Co.) and ground using the conventional series of abrasive papers. The polishing was done with 0-2 diamond abrasive on a Microcloth (Buehler Ltd.) lap, wet with xylene. After polishing, the surface was etched electrolytically in a 10 pct solution of chromic acid or in a 10 pct solution of potassium cyanide. Both reagents attacked the osmium-rich constituent, whereas the iridium constituent was attacked slightly by the chromic acid reagent and not noticeably by the potassium cyanide reagent. The results of the X-ray diffraction and microscopic examinations are summarized in Table I. Fig. 1 shows the microstructure of a 21 pct Ir-79 pct 0s alloy. The results indicate an appreciable solid-solu-bility range of osmium in iridium as was reported by Zvyagintzev.' The solid-solubility range of iridium in osmium is more restricted, apparently less than 21 pct Ir. This implies a large range of composition in which two phases can coexist that was not reported by Zvyagintzev.

Jan 1, 1955