Search Documents

By Albert B. Horn, J. J. McKetta, O. L. Culberson

Since water is present in natural gas and petroleum reservoirs, it is of engineering value to have accurate experimental data regarding the behavior of water in hydro-carbon systems. Since experimental data of this nature are so scarce in literature, a program is under way at the University of Texas to obtain experimental data regarding the distribution of water in petroleum hydrocarbons. This initial paper is subdivided into three parts: A. The apparatus and analytical procedure are discussed. B. The equipment has been checked by comparing the experimental data with data of literature on the solubility of methane in water at 77°F and pressures to 10,000 psia. C. Experimental data are presented at 100, 160, 220, 280, and 340°F on the solubility of ethane in water at pressures to 1200 psia. As the temperature is increased the solubility of ethane in water first exhibits a minimum and then a maximum solubility. The range of applicability of Henry's Law is discussed. INTRODUCTION Although considerable experimental data have been published on water-hydrocarbon systems in the hydrate region, the information on these systems in the vapor-liquid and the vapor-liquid- 'References are given at end of paper. Manuscript received at the office of the Petroleum Branch August 31. 1949. liquid regions at elevated pressures is extremely scarce. A survey of the literature on hydrocarbon-water systems at elevated pressures was presented by McKetta and Katz12,13,14 showing the systems and phases investigated. In addition to these existing published data, Poettman and Dean" have reported the water content of propane in the three-phase region (only the propane-rich liquid and the vapor phases were studied) and Michels, et al.15 have reported the solubility of methane in water at pressures to 6800 pounds per square inch at 77°F and at pressures to 1500 psia at temperatures to 300°F. It has been shown12,14 that the presence of water will materially affect the phase equilibrium of hydrocarbon systems. In order to make experimental studies on the quantitative effect of the presence of water in naturally-occurring hydrocarbon systems, it is desirable to have data available on binary hydrocarbon-water systems. A program is underway at this laboratory to determine the phase relations of the hydrocarbon-water systems. Initially the investigation will be limited to binary systems with water as one of the components. Later ternary and complex systems will be investigated and reported. EQUIPMENT AND ANALYTICAL PROCEDURE Apparatus In order to avoid a description of the methods employed in each subsequent paper, a description of the apparatus and the analytical procedure will be given here. The apparatus is shown schematically in Fig. 1. The numbered items in Fig. 1 represent the high pressure valves. The equilibrium cell is of the totally enclosed type, with a volume of 550 cubic centimeters. The cell is mounted in an air bath which in turn is mounted on pillow blocks and connected to a rocking mechanism so that the cell and bath will oscillate approximately 30 degrees above and below the horizontal at 35 oscillations per minute. The air bath is heated by two resistance heaters. The first or primary heater is 250 watts and is controlled by a thermoregulator; the second heater is of 500-watt size and is manually controlled to aid in bringing the cell to equilibrium temperature. Air circulation in the bath is accomplished by means of a fan. the shaft of which is concentric to the heaters. The walls of the bath are insulated with 2-in. thick blocks of 85 per cent magnesia. Temperature observations are made with three calibrated thermocouples. One couple is sealed in a well provided within the equilibrium cell, and is used as the criterion of the cell being at the equilibrium temperature. The other two thermocouples are located on opposite sides of the cell to indicate temperature uniformity within the air bath. The thermoregulator, used in conjunction with a relay, gives a variation in the temperature of the air in the bath of plus or minus one degree Fahrenheit. However, since the equilibrium cell weighs approximately 55 pounds, the

Jan 1, 1950

By Richard P. Rothwell

In January last I published in the Engineering and Mining Journal a table giving, with a considerable degree of accuracy, the production of anthracite coal for the year 1874. At that time it mas impossible to give any correct estimate of the production of bituminous coal, for the returns I had been able to secure from such distant and scattered districts were not always forwarded punctually, and the work of .obtaining anything like a true estimate of the coal mined in districts from which I was unable to obtain official returns was both laborious and tedious. As will be seen from the detailed reports furnished herewith, I have succeeded in obtaining tolerably accurate returns of 20,093,704 tons; and upon careful revision by numerous well-informed local authorities, my first estimate of the amount of coal not officially returned to me has grown very considerably; indeed, as I get more information on the subject I find that our bituminous coal production greatly exceeds the amount we have been accustomed to hear it placed at, aggregating as it does, 26,465,704 tons. Mr. Andrew Roy, State Inspector of Mines for Ohio, has reported the production of Ohio at 4,168,445 tons, while his first estimates were but 3,820,000 tons; and similarly, in other cases, the more full the returns direct from the mines the more incorrect do I find all previous reports. I am able now to furnish, not an accurate statement, indeed, but by far the most full and reliable one that has yet been published of our coal production. The amount of labor involved in obtaining this admittedly imperfect report has been simply enormous. In the following tabular statement it will be perceived that Pennsylvania produces nearly one-half of all the bituminous coal mined

By J. Walter Snavely

PRESENT-DAY processing in many industries, calcining, sintering, briquetting, beneficiation and nodulizing, increasingly calls for the handling of large volumes of hot bulk materials. Various types of conveyors have been employed. This discussion will cover the factors governing their selection. For temperature ranges up to 400°F, or approximately 200 °C, a wide range of conveyors is available. Special constructions of rubber conveyor belts, steel conveyor belts, vibrating and shaker conveyors, apron conveyors, and drag chain conveyors, all are used successfully. As temperatures go well above 400 2F, however, choice of conveyors is narrowly limited. This paper will consider the problem of handling bulk materials only where the temperatures exceed 400°F. The arbitrary selection of 400 °F as a dividing point undoubtedly can be challenged, as special conveyor belting constructions are available which are suitable for temperatures in excess of 400°F. However, when the relatively short life of such belts and the cost of their replacement, with the attendant down time, are balanced against the reliability and long service life of the properly designed steel constructed units to be discussed, there is little question in any operator's mind that the special belts are more expensive to use. Because the conveyors under study are for the handling of bulk materials, inevitably including a high proportion of fines, obviously wire mesh belts cannot be included for consideration. Even though this type of conveyor is widely used at high temperatures, i.e., for carrying glassware through a lehr, it is unsuited for the conveying of bulk materials, and therefore will be excluded from further discussion in this paper. Preliminary to the study of the conveyor itself is the determination as to whether the material is to be cooled while it is being handled, or whether the processing requires retention of all heat and the maintenance of a given temperature range. In the majority of cases cooling is incidental to or part of the handling process, when the handling, for example, follows completion of sintering, roasting, calcining, refining, or some other process. To meet such operating conditions successfully, the conveying medium used must have: 1—a construction capable of withstanding maximum initial temperatures of the material being handled. 2—a construction providing efficient heat transfer for cooling. 3—a construction providing dependable operation and long life with minimum service requirements, and 4—a construction providing controlled and efficient conveying. Under the usual conditions of cooling during the handling, the construction selected to withstand the initial maximum temperatures does not necessarily involve using alloys, as excellent results can be achieved with normal carbon steels and cast irons, when they are properly applied and proportioned. The earliest and simplest type of conveyor for handling very hot materials is the cast steel drag chain conveyor, still widely used for handling hot cement clinker, as illustrated by Figs. I and 2. Because of the rugged and generous proportions of the chain link design, low carbon steels are entirely suitable for the links. The pins, however, must be alloy steel. The simple, rugged construction of this type of conveyor makes it readily capable of withstanding high initial temperatures, even though the chain is operating buried in the material. The drag-chain type of conveyor has advantages and limitations. Although the efficiency of the heat transfer is relatively poor, the life of the conveyor is reasonably long, and because of its crude simplicity it does not require much servicing. However, as a conveyor, it is limited in capacity, and largely limited to horizontal runs. Furthermore, because of the crude design, heavy weight, and the chain operating at the temperature of the material, greatly reducing permissible operating chain pulls, this type of conveyor is limited to relatively short centers. Another type of conveyor that has been used for very hot materials is the cast pan conveyor. Because of its very generous proportions the cast pan, which is made of either cast iron or malleable iron, can withstand initial maximum temperatures. It also provides efficient heat transfer for cooling. Further, it is on efficient conveyor construction, which can be used for inclines. Because the chain employs rolling friction instead of sliding friction, and is not in the maximum temperature zone, much longer centers are possible. It is this type of conveyor that is frequently used in the casting of various metal pigs, pig iron, and aluminum; it is obvious, therefore, that very high initial temperatures are being handled. With this kind of conveyor the return run is frequently sprayed with water to accelerate heat transfer. The build-up of residual heat in the very heavy cast pans is thus overcome. The outboard roller steel pan conveyor is an improved pan conveyor' which provides high rates of heat transfer and substitutes formed steel pans for the heavy cast pans. It is a very efficient conveying medium. The details of this particular construction are clearly shown in Fig. 3. An early application of this type of conveyor is shown in Fig. 4. In this case the conveyor units are handling roasted phosphate rock at average temperatures of 1000" to 1500°F, and frequent maximum temperatures as high as 1900°F. Several widths are used. The capacity of the unit at a speed of 50 fpm is approximately 30 tph per inch of width at peak loadings, average capacity being about 1/3 of peak loading. The assembled conveyor is shown in Fig. 5, with views of both the top and the underside to show all the construction details. In particular, the following general design principles were carried out in this construction:

Jan 1, 1954

By H. W. Gillett

Unlike most previous Howe lecturers, I had not the good fortune to be associated with Henry Marion Howe, nor to be directly one of his students. Yet, through his writings, he has been my teacher, as he has of all American metallurgists. Instructive as his writings are—I use the present tense because Howe thought so keenly and reasoned so surely, seeing clearly, as if by intuition, what was hazy to lesser minds, that his writings are still vital—it is not those books and papers, nor even the minds he trained in his classes, that were his most outstanding service. It was the spirit of Howe in his approach to the problems of metallurgy, his broad-mindedness and fairness, his recognition of the need for theories and hypotheses to explain metallurgical phenomena, his willingness to use them as servants, as well as his questioning attitude—his refusal to accept them as masters—that comprise his greatest service. This most thoroughly warrants the honor the Institute pays each year to his memory. These traits I so respect and honor in any man that I glory in this opportunity to do reverence to him in whom they were so notably united. Howe's Discussion of a Creep Problem I have often wished that Howe were still with us to turn his keen insight upon the problems of the use of metals at high temperatures, a field much studied but still very hazy. Indeed, 53 years ago, in a paper1 before this Institute, Howe stated a problem closely allied to some that still perplex metallurgists and engineers dealing with the high-temperature field. Howe was intrigued by a report2 from another old master, Robert Henry Thurston, on the behavior of annealed vs. cold-drawn iron wire, and in order to broaden the foundation for metallurgical generalization, Howe made experiments of his own on copper and silver. In these tests by Thurston and by Howe, the wires were rapidly loaded to determine the

Jan 1, 1939

By G. B. Gould

FROM the very inception of the price-control experiment in the bituminous-coal industry, the problem of price differentials was of major importance. In fact, assuming that there will be no legal or Govern- mental obstacles to price control, the successful maintenance of the present or any other method designed to control bituminous-coal prices will depend upon the discovery of some satisfactory way to determine these differentials in price, among: individual mines and groups of mines. Being of organic origin, bituminous coal is a commodity that presents an almost infinite variety of qualities. It is inevitable, therefore, that a work- able price-control system must attempt

Jan 1, 1935

Henry LOUIS, London, England (communication to the Secretary) : Prof. Richards's paper has impressed me as highly valuable. Without entering upon any discussion of it as careful and thorough as it deserves, I venture to mention one or two points which a perusal of it has recalled to my mind in connection with my own study and practice of ore-dressing. I always mentally divide jigging into two phases: 1. A particle at rest on the jig-bed is lifted and carried upwards by the rising current of water, at an increasing velocity, which tends to a maximum. When the upward current is stopped, the particle continues to rise with rapidly diminishing velocity until it comes to rest. This completes the first phase. 2. In the second phase, the particle falls from its position of rest with an increasing velocity which tends again to a maximum, and continues to fall until the rising current of water has reduced its velocity to zero. This completes the second phase. The second phase will evidently be greatly modified by the effect of suction, as Prof. Richards shows; but I do not see that his experiments very clearly imitate the action of the second phase. And the brief intervals at the end of each phase, when the mineral particle, by reason of its acquired velocity, is still moving, though in opposition to the water-current, yet remain to be investigated. I feel especially, in Prof. Richards's paper, a difficulty which I have felt with regard to all similar previous investigations, namely, that the experiments deal with particles falling a long distance, when the velocity becomes uniform. I question whether this uniform maximum velocity is attained in actual jigging-practice. If so, it is certainly for a comparatively very small proportion only of each stroke. It seems to me that an investigation like that of Prof. Richards, but confined to the first 6 or 8 inches of fall only, and carried out with suitably delicate recording-apparatus, is what we

Jan 1, 1895

By J. G. Early, F. V. Lenel, G. S. Ansell

The isothermal shrinkage rates of copper-powder compacts were determined in the temperature range from 760o to 1060oC. The rates for compacts fabricated from a pure spherical copper powder were compared, on the one hand, with those fabricated from a spherical powder containing a dispersion of aluminum oxide in the copper matrix and, on the other hand, with those fabricated from a pure copper powder having irregularly shaped particles. The irregular copper-powder compacts shrank much faster than the spherical copper-powder compacts and these, in turn, shrank faster than dispersion -strengthened copper -powder compacts. The experiments were run under a small external load. By varying this load, the stress dependence of the isothermal shrinkage rate could be measured for compacts from spherical-copper powders. This stress dependence was found to be approximately proportional to the 4th (dispersion-strengthened alloys) or 4.5th (pure metals) power of the stress. It is concluded that the material-trans port mechanism is due to dislocation climb rather than to Herring-Naharro creep. In this investigation the isothermal shrinkage rates of compacts made of copper powder with an average particle size of 70 g in the temperature range from 780o to 1060°C were studied. The aim of the investigation was to determine the mechanism of material transport responsible for the shrinkage of these compacts. Since the phenomenon observed in this investigation was shrinkage of compacts at high temperatures, it will be necessary to consider all the material-transport mechanisms possible in sintering. It is unlikely that evaporation and condensation, surface diffusion, or even volume diffusion of vacancies, in which surfaces of small radius of curvature are vacancy sources and those of larger radius of curvature vacancy sinks, will materially contribute to a sintering process involving shrinkage, i.e., one in which the centers of adjacent particles move towards each other. The two principal mechanisms which were considered were the so-called Nabarro-Herring mechanism and a plastic deformation mechanism by dislocation movement. Both of these mechanisms were originally conceived to explain creep, i.e., the plastic deformation of metals at elevated temperatures under a constant applied stress. The shrinking of metal-powder compacts which was studied in this investigation can be readily treated as a creep process. This means that the shrinkage rates observed are considered as creep rates under the influence of an applied stress. It is true that the stresses in sintering experiments are generally not constant but decrease continually with time, but, by considering creep rates or shrinkage rates over a relatively short time interval, the small changes in stress during this time interval can generally be neglected. Nabarro-Herring microcreep is a high-temperature deformation mechanism which is caused by a diffusional flow of vacancies from boundaries under a tensile stress towards those under a compres-sive stress. Herring1 has shown that in this type of microcreep the strain rate e is proportional to the applied stress and follows an equation of the form ma, aexp(-Q/RT) [l| where <j is applied stress, Q is the activation energy for self-diffusion, R is the gas constant, and T is the absolute temperature This type of creep can explain the shrinkage of a porous compact. The surface of the pores are subjected to the tensile stress of surface tension, while the grain boundaries are under a compressive stress also due to surface tension. Vacancies diffuse from the pore surface through the lattice to the grain boundaries, where they are eliminated. In order to maintain vacancy equilibrium at the pore surface the vacancies leaving the region of the pore surface are replenished from the volume of the pore, which means that the pores shrink.

Jan 1, 1964

By A. H. Dierker

Next to the metal itself, molding sand is the most important raw material used in the manufacture of steel castings. There are no accurate figures available but probably it would be safe to say that the average steel foundry uses approximately 1000 lb. of new molding sand per ton of castings produced. With untreated sands costing from two to four dollars (in some extreme cases it may run as high as eight or ten dollars) per ton delivered at the foundry siding, molding sand is an important item in the cost of making castings, and any information that may help to reduce this sand consumption should be of interest to the industry. Fundamental Considerations In a general way, molding sand in the average steel foundry passes through the cycle shown in Fig. 1. This diagram indicates that if all of the sand could be returned from the shakeout floor to the mixer no new sand would be required from the stock pile and molding costs would be reduced accordingly. Unfortunately, for reasons to be discussed later, it has heretofore been necessary to dilute the used sand constantly with new raw sand in order to maintain the properties that are essential to the production of satisfactory molds.

Jan 1, 1930

By N. Schapiro, R. J. Gray, G. D. Coe

A petrographic and chemical investigation was conducted to determine the occurrence and distribution of the organic and inorganic forms of sulfur in various size and specific gravity fractions of a high volatile, A-rank, Pittsburgh seam coal. The investigation was conducted to aid in the resolution of the problem of how metallurgical coke of lower sulfur content can be produced from high sulfur coals. The Pittsburgh raw coal contains about 2.4% S in two dominant forms: pyritic and organic. Pyritic sulfur constitutes about 57% of the total sulfur in the raw coal and occurs in macroscopic and microscopic-size particles. A plant cleaning process mechanically separates between 50 and 60% of the pyritic sulfur, mainly the macroscopic particles. The organic sulfur constitutes 41% of the total sulfur in the raw coal and 55% of the sulfur in the washed coal. Thus, organic sulfur is not reduced by physical methods of separation. Organic sulfur occurs in all the coal entities, but in general, increases as the exinoid content of the coal increases. In this study, it was found that carbonizing certain selected low gravity coal fractions containing an average of 0.45% pyritic sulfur and 1.01% organic sulfur produced cokes containing an average of 0.22% pyritic sulfur and 0.91% organic sulfur. However, the organic sulfur in the coke is probably derived in part from the heating of pyrite in the presence of carbon. Thus, the total sulfur in the coal carbonized is the most important factor affecting the sulfur content of the coke produced. Concentration of microscopic pyritic and organic sulfur in the middling-type coal indicates the necessity for rejecting as much of this material as is economically feasible. Most of the sulfur introduced into the blast furnace originates from the coke. Although the sulfur content of the hot metal can be controlled by the addition of flux, the flux used restricts the productivity of the furnace by displacing ore and requires first to be smelted; therefore, low sulfur coke is highly desirable. Since the sulfur content of coke is dependent upon the sulfur content of the coals from which the coke is produced, low sulfur coals are required to produce low sulfur coke. In the western Pennsylvania area, large quantities of good coking coal are available from the Pittsburgh seam, but this coal unfortunately contains relatively large quantities of sulfur. To provide information that might be useful in reducing the sulfur content of this coal in the cleaning process, an investigation was conducted to determine the physical and chemical forms in which this sulfur occurs and with what petrographic components it might be associated. The Pittsburgh seam coal, like most other coals, contains two dominant forms of sulfur: one occurs as the minerals pyrite and/or marcasite and is referred to as pyritic sulfur; the other is combined with the coal substance and is called organic sulfur. Pyritic sulfur is amenable to physical methods of separation, whereas organic sulfur is not. Pyritic sulfur particles must be freed from the surrounding coal if they are to be removed in the washing process. Generally, this requires crushing; the required degree of crushing being a function of the size and distribution of the pyrite. The present investigation was conducted to 1) determine the size, distribution and association of sulfur-bearing minerals in the coal and 2) to determine whether the organic sulfur has a preferential association with specific coal entities. If a preferential association exists, this knowledge may be useful in devising a method for organic sulfur reduction. In addition, a study was made to determine the extent to which pyritic and organic forms of sulfur in the coal contribute to the sulfur in the coke produced from this coal. A representative 3%-ton sample of raw coal was crushed to —3 in. and screened into square-mesh sizes: 3 to 1 in., 1 to % in., % to % in., % in. to 10 mesh, 10 to 35 mesh, and 35 to 200 mesh. Separate samples of the -200-mesh fraction and the all-size composite were also collected. Each size fraction (except the -200 mesh) was fractionated on heavy liquids of the following specific gravities: 1.280, 1.300, 1.325, 1.350, 1.375, 1.400, 1.425, 1.450,

Jan 1, 1963

By David E. Hyatt

The chemical attributes of cyanides have long been exploited in ore pro- cessing schemes for the recovery of copper, molybdenum, gold, silver, and other metal values. Blast furnacing operations are significant unintentional producers of cyanides which find their way into process waters. Many of the more than 20,000 electroplating facilities in the United States utilize cyanide plating baths and generate cyanide containing wastes. As social, political, and economic pressures for water quality attainment, maintenance, and preservation grow, the requirements for the development of treatment technology to control cyanide levels in wastewater become increasingly apparent. Just as the chemistry of the cyanide ion 1s an integral part of its industrial applicability, so must this chemistry be a fundamental part of any decomposition or removal technology used to control its level in effluent or recycled waters. The complexity of this chemistry is substantial and it cannot be considered in a superficial or cursory manner if control system design is to be both efficient and reliable.

Jan 1, 1975

By J. J. Kramer, W. A. Tiller, G. F. Bolling

THE axial orientations of columnar crystals in unidirectionally solidified ingots of zone-refined zinc and tin have been examined using the techniques recently described by us.&apos; Both metals had an initial purity of 99.999+ pct before zone refining and satisfied all qualitative guides for very high purity after zone refining. Fig. 1 presents the orientations of the columnar crystals for tin and zinc, respectively. For tin, there is a preference for grains growing in the [I101 direction, i.e., the dendrite direction.&apos; For zinc, a weak preference for the [0001] direction is seen (a random population in the unit triangle would give equal density on either side of the 60-deg circle centered on [0001]).&apos; There was no apparent evidence for dendritic growth in either metal. These results, and those previously reported,&apos; confirm the recent investigation by Hellawell and Herbert of casting textures observed for zone-refined lead, zinc, and tin.4 The preferred casting orientations for these metals in both the impure and zone-refined states are given in Table I. In the experiments on zone-refined lead,&apos; it was shown that two separate textures existed: a preferred (111) nucleation texture existed at the chill surface and a preferred (111) texture developed during solidification. Either effect is sufficient to produce the result recorded in Table I. Similarly the results recorded for tin and zinc may be attributable to either a preferred nucleation or a preferred growth phenomenon and additional experiments are required to separate these two possible explanations. Hellawell and Herbert&apos; attribute their results to a preferred growth process and account for it on the basis of a "layer-growth" model proposed much earlier by one of the present authors.5 An equally satisfactory growth model would be that based upon anisotropic surface energies. However, both of these growth models would indicate that the preferred growth direction for very pure metals should be normal to the plane of closest packing in the metal. This is consistent for zinc but, contrary to the conclusion of Hellawell and Herbert, it is not consistent for tin since here the (100) is expected to exhibit a greater density of packing than the (110). Although tin is expected to exhibit an anisotropy of thermal conductivity, we would expect the thermal conductivity to be the same in the [1101 as the [l00]

Jan 1, 1963

By D. E. Norquist, J. E. Moeller

The results of wear on marked balls, 4, 31/2, 3, and 2 in. diam are given. All balls were forged steel of practically the same chemical analysis and hardness. The results indicate that balls in a given mill for a given length of time will have equal diameter losses, regardless of size.

Jan 1, 1950

By Pervez Patel, Martin G. Frohberg, Demetrios Papamantellos

Model experiments were carried out on the mass transfer of iodine between n-hexane and a 4 2 X 10-3 M aqueous sodium hydroxide solution. The influence of mechanical stirring by means of small gas bubbles (ca. 0.01 ml in volume) on mass transfer was examined in independent experiments. The results were described with the help of the penetration theory and in the case of bubble stirring with the help of a mathematical model based on this theory. S LAG-METAL reactions, especially those in steel-making processes, often occur under conditions where gas is evolved in the form of bubbles that break through the slag-metal interface. It is known that stirring by means of bubbles increases the mass transfer coefficient, but there has been very little quantitative work done in this field. Because of the difficulties that attach to experimental work at high temperatures this study was confined to model experiments at room temperature. EXPERIMENTAL APPARATUS The transport of iodine from an n-hexane layer into a weak sodium hydroxide solution was studied a) with stirring by means of bubbles and b) with mechanical stirring. The apparatus for the experiments with bubbles consisted of the cell, two Dreschel bottles filled with hexane in order to saturate the nitrogen flow, one flow meter, and a nitrogen gas cylinder fitted with a fine-regulating valve. Fig. 1 shows the cell consisting of a glass cylinder 33 cm in height with an overall diameter of 7.5 cm embedded in a copper flange. The flange is connected to a Plexiglas plate and to the gas inlet. The Plexiglas plate has holes of 0.2 mm diam bored into it which are spaced 1 cm from each other. For the experiments with mechanical stirring the bottom of the cell was sealed off by a Plexiglas plate. The upper layer was stirred by means of a glass stir-rer and the bottom layer with the help of a magnetic stirrer in a counter rotatory direction. Both stirrer speeds could be varied continuously. EXPERIMENTAL PROCEDURE Iodine dissolves in n-hexane producing a stable violet color thus enabling the iodine concentration in

Jan 1, 1970

By R. R. Sayers

SILICOSIS is a term known to almost everyone today. Yet, in spite of a great deal of study, much is still to be learned regarding the disease. Government organizations are still continuing their investigations, begun near Joplin, Mo., 25 years ago. Work is also being done in several universities, as Harvard, Pennsylvania, Rochester, and Toronto, and at least two private organizations, the Air Hygiene Foundation of America, Inc., and the Saranac Laboratories for the Study of Tuberculosis, devote most of their time to this subject. Similar studies have been and are being made in many other countries.

Jan 1, 1939

By W. D. Ludemann, J. E. Dor, L. A. Shepard

Recovery of the creep resistance of 99.99 pct pure Al was studied at temperatures 540°, 573°, 600°, and 611°K. Poly-crystalline specimens crept under a stress of 950 psi to a strain of 5.5 pct were allowed to recover for periods of from 1 min to 16 days under a residual stress of 4.4 psi. Increased creep rates upon reapplication of the 950 psi stress evidenced softening of the material. The activation energy for the recovery process was found to be 64,000 cal-per mol. THREE major observations have clearly revealed that the creep of polycrystalline aluminum above about 510°K is controlled by the rate of climb of jogged edge components of dislocations past the barriers impeding their motion: 1) Extensive polygonization, characteristic of climb, takes place during creep.&apos;9&apos; 2) The activation energy for creep equals the estimated activation for self-diffusion. 3) The stress law for creep coincides with theoretical predictions based on the climb mechanism.4,5 The decreasing rate during the primary stage of creep must be ascribed to the introduction of additional barriers to the glide of dislocations. During secondary creep the density of barriers must remain constant, the rate at which new barriers are formed being equal to the rate at which they recover. For this reason the nature of the barriers, and their rates of formation and recovery, are significant to a complete understanding of creep. It is proposed here to study the kinetics of the recovery of barriers to creep of high-purity polycrystalline aluminum in the climb range. The technique will consist of creeping a series of tensile specimens under a prescribed stress to given state following which the specimens will be recovered for various times and temperatures under approximately zero stress. The amount of recovery will be determined by comparing creep curves following the recovery. EXPERIMENTAL PROCEDURE The material used for this investigation was a 99.99 pct pure Al supplied by the Aluminum Co. of America in sheets of 0.001-in. thickness having an H-18 temper. The spectroscopic analysis of impurities gave Cu-0.004 wt pct, Fe-0.002 pct, Si-0.001 pct, others-0.000 pct. Creep specimens were machined with their tensile axes in the rolling direction of the sheets. Annealing in a molten potassium nitrate-potassium nitrite bath for 1 hr at 686K, followed by air-cooling, resulted in a grain diameter of from 0.22 to 0.27 mm. Creep machines were equipped with constant stress lever arms of the type suggested by Fullman, Carreker, and Fishher,&apos; which maintained the applied stress to within 0.04 pct of the reported value of 950 psi. Creep strains were calculated from extensions over a 6-in. gage section to the nearest 3 X 10"5. The temperatures of testing, 540°, 573", 600°, and 611°K, were obtained by immersing the specimen and extensometer assembly in a molten KNO2-KNO3 bath. Temperatures during the periods of creeping could be maintained constant to within better than ± 1°K. Correlation of creep data at different temperatures of testing demanded the use of an appropriate temperature-compensated time 8. Previous investigations have shown that the creep of pure metals at temperatures above about 0.55 of their melting temperatures can be correlated by the functional relationship3" e=f(0), s= const. [1] where e = total plastic strain during creep f = a function that depends on stress a = stress 6 = te-Q/RT = a temperature-compensated time t = time under test Q = 35,500 cal per mol = activation energy for creep R = gas constant, and T = absolute temperature In the present series of tests all of the creep was conducted under the same stress of 950 psi. To provide identical initial conditions for the recovery all specimens were first crept to a temperature-compensated time of = 47 X 10-14 min which resulted in a creep strain of 0.055 + 0.005 regardless of the creep temperature. During recovery, a small stress (4.4 psi) was permitted to remain upon the specimens to maintain tautness in the pulling assembly and to prevent mechanical damage to the soft specimen. After each recovery period, the full stress was reapplied and

Jan 1, 1961

By G. R. Fritterer

INVESTIGATORS in the field of temperature measurement have long sought a thermoelectric couple fulfilling the following requirements: 1. It should be useful up to and including high industrial tempera-tures; i. e., 1000° to 1800° C. 2. Its thermoelectric variation with temperature should be linear and be maintained after heating to high temperatures for long periods of time. 3. It should be reproducible; i. e., different couples of the same elements should have similar calibration curves. 4. Its thermoelectric power should be large so as to allow the industrial use of rugged recording instruments. 5. Chemical reactions with, and physical changes within the elements of the couple should not alter its calibration. No thermocouple proposed to date exhibits simultaneously all of these characteristics, whereas the couple about to be described fulfills all requirements to a satisfactory degree.

Jan 1, 1933

By David R. Mitchell, Ernest M. Spokes

There is evidence that study of minerals now considered to have susceptibilities too low for magnetic separation should be continued. Present concepts may be false. INFORMATION on magnetic properties of minerals other than magnetite is scanty and sometimes erroneous. Often there is no information at all. W. R. Crane&apos;s table of tractive forces published in 1901 is still the best guide in the field, but Crane&apos;s data can be used as a guide only, since he ignored such important factors as impurities in the minerals, size, and packing effect. During the 1930&apos;s work by the U. S. Bureau of Mines added greatly to knowledge of the behavior of certain minerals in a magnetic field. The USBM bulletin gave for the first time complete magnetic characteristics for magnetite and fragmentary data for a few other minerals. The work reported here covers a study of the magnetic-susceptibility relationships of the wolframite series of minerals and sphalerites as related to their chemical compositions. Theories are proposed to explain divergences found from commonly accepted beliefs. Gouy Method for Determining Magnetic Susceptibility: The Gouy principle has been adequately described in the literature1-3 and applied in various ways.&apos;- It may be summarized by stating that a body of material (gas, liquid, solid, or powder mixed with gas or liquid) of cylindrical shape changes in apparent weight if suspended with one end in a zone of higher magnetic field strength than is found in that portion of the field surrounding the other end of the cylinder. This may be expressed as K2 - K1 A (H2 - H2) - mg. [1] In determining the susceptibility of mineral specimens by the Gouy method, the mineral is reduced to a fine powder and packed in a glass weighing tube. Precise measurement of the bore and depth of the tube is made unnecessary by a calibration procedure. Using the basic expression of Eq. 1, Hoare"

Jan 1, 1959

By H. D. Wilde

DURING 1934 conditions in the production division of the petroleum industry were reasonably satisfactory but nevertheless a decided feeling of insecurity existed largely because of the uncertainty of controlling production to consumptive demand. Over-production, especially in the East Texas field, threatened a general collapse of crude prices but in spite of this, posted prices were high. Stimulated by the prevailing posted prices, wildcatting activities were wide-spread. Although a number of small discoveries were made, particularly in the Gulf Coast belt and Oklahoma, no fields of major importance, unless it was the Fitts pool in Southern Oklahoma, were brought in. Meanwhile, the Petroleum Division of the A.I.M.E. continued its activities. It sponsored the collection of production and geological data on both foreign and domestic fields. The data on all but a few producing districts in the world were published in the "Petroleum Development and Technology" volume of the "Transactions" and comprise one of the most complete tabula¬tions of this sort ever published. Work of this kind is being continued.

Jan 1, 1935

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922