Search Documents

By H. J. Maguire

Those familiar with mill-practice understand the work required of an average bucket-elevator, but I wish to call special attention to the wear on the buckets. I have been studying in what manner the life and service of the bucket might be improved, and I feel that an adjustable lip, attachable to each bucket without the aid of rivets, will be of material advantage. For illustration, consider the feed-elevator of a typical mill in the Cæur d'Alene district. The ore is carried by water in a launder from the feed-rolls and dumped in the " boot" of the elevator, directly in front of the ascending bucket. Middlings from the return-rolls are similarly handled. Under this condition the bucket not only carries the ore, but also picks it up, and this latter requirement determines the life and service of the bucket. It might be said that it would be better practice to convey the feed to the elevator and dump it directly into the bucket, but at one mill at which this plan mas tried the results were disappointing and the rubber belt was badly worn. The wear of the bucket is confined to the lip and the corners which have to pick up the material. When the lip on a corner of a '7- by 12-in. malleable cast-iron bucket is worn down about 3 in., the bucket is of no further value as a carrier and has to be replaced. The worn bucket, containing about three-quarters by weight of the metal of the original bucket, has a scrap value of about 10 per cent. of that of a new bucket. To the cost of the bucket, however, should be added the time-

Jan 1, 1913

By H. W. Imholz

Considerable stimulation was given to the interest in the lower producing zones of the North Central Texas area when several wildcat wells developed production in these formations. The Iron Mountain and Humble-Olander well in sec. 196, B.B.B. and C. survey, Jones County, Texas, had a potential of 7500 bbl. (after a 3000-gal. acid treatment) from the Palo Pinto limestone encountered from 3238 to 3250 ft. This well heightened the prospects for oil in commercial quantities in the Canyon, Strawn, Bend and Ellenburger formations in the adjoining counties of Shackelford, Haskell, Throckmorton and others. The Hickok-Van Parmer well in sec. 477 S.P.R.R. Co. survey, Eastland County, Texas, was good for 1040 bbl., natural, from the Ellen-burger limestone, encountered from 4024 to 4033 feet. The Hal Hughes-Cook and Jordan (Poindexter) well in sec. 350, block 6, S.P.R.R. Co. survey, Callahan County, flowed 890 bbl. in 9 hr., after acid treatment, from the Ellenburger limestone, encountered from 4369 to 4388 feet. Both of the Ellenburger wells apparently are maintaining the pressure and volume of their original potential tests, and will no doubt open up considerable area in the adjoining counties for prospecting to the Ellen-burger limestone. Production increased in the district from 12,081,871 bbl. in 1936 to 15,384,500 bbl. The increase was due to developments in Jones and Jack Counties. Jack County production increased from 896,680 bbl. in 1936 to 3,117,063 in 1937, while Jones County increased from 1,596,743 bbl. in 1936 to 2,289,322 in 1937. The remaining counties of the district showed a slight decrease in the amount of oil produced.

Jan 1, 1938

By O. E. Kiessling

Viewed from the standpoint of an economist, the task which faces the petroleum producing industry is one of intelligent adjustment so that technology can perform the job of efficient exploitation, while at the same time the interests of producers and consumers remain adequately protected. The crux in the task of making this adjustment lies in the difficulty of arranging the instrumentalities of production to accord with the physical characteristics of oil. For example, oil is exploited under a competitive economic system based on private ownership and contract, with the hope that profits will attract capital and enterprise, and with competition supposedly acting as the regulative factor. Whether such a scheme of industrial organization works is partially dependent upon the ability of the producer to withold or produce his commodity as he sees fit, in accordance with market demand. But in the oil industry, the enterpriser does not have complete control over the expansion and contraction of production, for, because of the decisions of the courts that ownership in oil depends upon its possession, desire for immediate output becomes the controlling force in production. Consequently, the theoretical commands and restraints of free enterprise are not operative because there is no security of property, and the result is loss due to the following economic maladjustments: (1) Production not completely responsive to price control. (2) Production at excessive cost. (3) Loss of oil, a highly exhaustible natural resource. If economic maladjustments are to be eliminated, there should be a change in the organization of production so as to provide efficient exploitation of the oil and at the same time to insure individual property interests. The latter is necessary if economic considerations are to become primary factors in regulating production. To attain these ends, the entire pool should be developed as one big engineering project and some scheme

Jan 1, 1928

By A. L. Mular

Two equations express the integral rate at which fines are produced from a homogeneous material: It has been demonstrated that the Gaudin-Meloy distribution for single fracture is equally applicable to multiple fracture and is related to the Gaudin-Schuhmann distribution at least when the distribution modulus a is close to unity. A, xoY was found to be independent of starting mass over the range studied when particle size was held constant. The equations are related to the input energy to the mill. In an earlier paper,' it was shown that when Mo g of uniformly sized homogeneous material is ground dry in a batch rod mill, the energy-size reduction equation is expressed at any time by the mass of unbroken starting material left at time t, ku is the size modulus of the portion Mo - Mt, and P is a constant that is generally equal to the distribution modulus a. If the power to the mill is constant, Et is proportional to time and Eq. 1 is rewritten where (Mo -Mt)/t is actually the integral rate at which fines are produced from a parent material, and A, is another constant. The size modulus, k,, is determined from the Gaudin-Schuhmann equation:2 where y is the cumulative fraction finer than any size x. Recently, Gaudin and Meloy derived a distribution equation for single fracture on the assumption that the random fracture of a homogeneous material produces daughter particles of similar shape. Their equation is given by where y is the cumulative fraction finer than size X, x, is the size of the unfractured parent, and r is designated the size ratio. Although Eq. 4 is derived for a single event, it should also approximately hold for a series of com-

Jan 1, 1962

By Milnor Roberts

The Nicola Valley coal-field is small, but it seems likely to become important because of its commanding position in a rich region that is developing rapidly. Bituminous coking-coal in workable quantity has not been found at any other point between the Crow's Nest Pass region, about 400 miles to the east, and Vancouver island, 250 miles westward. The Canadian Pacific railway reached the Nicola valley two years ago ; two other lines, the Canadian Northern and the Great Northern, are building towards the valley. The vast region between the Rocky mountains and the Pacific coast, extending northward for several hundred miles from the international boundary, which has been the scene of extensive mining- and smelting-operations for many years, is filling up with settlers, who are attracted by the wealth of minerals and timber, the rich soil of the valleys, and the fine climate. The Nicola river, flowing westward through the valley of that name in the Yale district, discharges into the Thompson river, which is the eastern branch of the Fraser. The transcontinental line of the Canadian Pacific railway crosses the mouth of the Nicola river at Spence's bridge, 178 miles from Vancouver. From Spence's bridge the Nicola branch line ascends the valley for 40 miles to Merritt, the coal-center, and continues 7 miles farther to the town of Nicola. Thus the haul from the mines at an elevatioiz of 2,000 ft. to salt water is 218 miles down river-grades. The Nicola branch will be continued about 150 miles farther eastward to Penticton, where it will connect with an extension of the line through the rich Kootenay and Boundary districts. The Canadian government has granted a subsidy of $6,000 per mile, to which the provincial government is planning to add $5,000 per mile, to assist in the construction of the Nicola extension. Upon the

Jan 1, 1910

By Benj. Lyman

The Institute, in June, 1881, visited Low Moor in Alleghany County, Virginia, on the Chesapeake and Ohio Railway, seven miles easterly from Covington. Having occasion myself, a few days later, to make a very hasty geological reconnaissance of the iron-ores there, and finding them to be somewhat different in age from what was said to be the opinion of some of those who were there with the Institute, I have thought it worth while to bring the matter up again at the present meeting. According to the opinion quoted, the principal ore-banks belong to the Oriskany sandstone; and that seems to be the view entertained of the same ore in that region by Prof. Wm. B. Rogers in his reports of 1837 and 1838. it is likewise given by Prof. J. L. Campbell in a paper on the Rich-patch iron region in The Virginias for December, 1880 (vol. i., p. 189). A comparison, however, of the section at Low Moor with sections in Pennsylvania, shows clearly that the main ore-bed is the same as that of the bottom part of the Marcellus shales (part of Pa. and Va., No. VIII), a short distance above the top of the Oriskany sandstone (No. VII). The Upper Helderberg limestone is absent at Low Moor, as indeed it is at many places in Pennsylvania, and that is perhaps the reason why the ore has been thought to belong to the Oriskany sandstone. The ores and their accompanying rock-beds, are exposed in three or four folds near the Low Moor iron-mines on Fork Rim and, as described and pointed out by Mr. Geo. T. Wickes, who had in his management of several years' duration become well acquainted with them, are as follows, from above downwards:

Jan 1, 1886

By P. H. Royster

SOMETHING of a mystery has attached itself to the production of ferromanganese in the blast furnace. This alloy has been produced on the Continent almost continuously since 1876 and in very considerable tonnages, but little definite information concerning the practice is to he found in technical literature, and almost nothing in the way of a theory of the manganese furnace. In this country prior to 1904, bit one company had attempted its production in a serious way, and none of the operating data or other information from this company has been, or is, available to the public. In the last 5 years, as a result of the restriction of imports, a number of furnaces have been blown in on this alloy, with the result that in 1918 as many, as 18 furnaces were in blast. The majority of the men in charge of these furnaces had had little previous experience in such operations. Realizing the advantages both to the country and to the industry from a pooling of operating data and experiences, the Bureau of Mines, in the summer of 1918, undertook the collection of data from ferromanganese furnaces. Although the results of this investigation have already been reported to the companies cooperating, they may he of permanent metallurgical interest, so this paper attempts to give, briefly, the more important points brought out in the investigations. OPERATING DATA IN FERROMANGANESE PRACTICE Operating data were collected by the Bureau from 11 ferromanganese furnaces, which will be referred to throughout this paper as furnaces A, B, C, F, G, I, J, K, L, M, and P. The dimensions, of seven of the furnaces are given in Table 1. The companies from whom this infor-

Jan 2, 1919

By James P. Roe

Steel has occupied such a prominent position in most minds during the last thirty years, particularly since the introduction of the basic open-hearth process (by which the field from which the raw material could be obtained has been so widened), that little attention has been made to improvements in puddling iron. In fact, the general tendency seems to have been to accept the prediction that puddled iron is doomed. Events have in a measure justified such a forecast, due in large part to the introduction of mechanical appliances and operations with large units in the manufacture of steel, from which much lower costs have resulted. But this general tendency has met checks in certain directions. This is notably the case where the finished product is a welded one, or is subject to oxidation, to shock or to vibration; and, as far as the writer's observation goes, the bond (which is largely a mechanical one) is not as close and lasting between steel and tin or zinc as between iron and the same materials. The field still open for puddled iron is, therefore, a large one, provided the low costs of steel-manufacture can be approached. The process of puddling is one of the most interesting in the metallurgy of iron, as the reactions and the changes effected are apparent. The subject has had the strongest fascination to the writer from boyhood, and has led, not unnaturally, to a close study, which long ago resulted in the conviction that it could be successfully carried out with large units and by mechanical means. That others have also drawn these conclusions is shown by many undertakings, though there have been few such attempts during the last twenty-five or thirty years. Puddling cousists, essentially, in the removal of most of the carbon and silicon, and part of the phosphorus and sulphur

Jan 1, 1903

By D. N. Stevens, D. N. Bloom, M. A. Klugman

This paper represents a portion of a larger study concerning dispersion of major, minor and trace elements in wall-rock about orebodies in part of the Colorado Mineral Belt. This phase of the work pertains to the Mg/Ca ratio variations in wall-rock adjacent to orebodies in two mines, one in the Horseshoe Mining District (Hilltop mine), and the other in the Alma Mining District (Phillips mine). The two districts lie adjacent to one another, the Horseshoe District on the south and the Alma District on the north, and are commonly referred to as one, the Alma-Horseshoe Mining District. The Alma-Horseshoe Mining District is located 80 miles southwest of Denver, Colo., (Fig. 1) in Park County, on the eastern slope of the Mosquito range. The area is typified by rugged relief with altitudes of from 10,500 to 14,000 ft. The Horseshoe District is separated from the Lead-ville Mining District by the crest of the Mosquito range, with the Leadville District to the west. The Alma-Horseshoe District has been considered as peripherial to the Leadville District, and has not received the detailed attention that the Leadville District has. These two mines were selected for this study because of their ease of access; the attitude of the workings and the drill holes to the known mineralization; the similarity of the mineralization; and because the mineralization occurs in carbonates in both mines but are of different ages. In the Hilltop mine mineralization is confined to the Leadville dolomite (Mis-issippian) and is principally lead with subordinate zinc and silver. In the Phillips mine the mineralization occurs in the Peerless dolomite and shale (Cambrian) and in the Manitou dolomite (Ordovician) and is principally zinc with subordinate lead, silver,

Jan 1, 1964

By Nicholas J. Grant, Henry Epstein, John Chipman

FOR many years steel producers have been concerned with the presence of hydrogen in steel. Hydrogen dissolved in excess of its solid solubility at the melting point may cause bleeding and gross unsoundness in ingots and castings. In fully-killed steels the hydrogen content which results in these difficulties varies with the alloy content1 and may range from 6 to 12 ppm.* It is also recognized that of heat treatment diminishes rapidly as the size of the part to be treated increases. The time required to remove a specified fraction of the hydrogen present increases as the square of the diameter of the section, making the treatment of large- sizes impractical. In order to prevent bleeding and gross unsound-ness due to hydrogen, and in view of the inadequacy of corrective heat treatment alone to provide optimum properties when hydrogen is present in large sections, efforts to limit the hydrogen content must be taken while the steel is still liquid. The main subject of this paper is a discussion of the factors affecting the hydrogen content of liquid steel in acid and basic open hearth, and basic electric two-slag furnace processing. Literature Survey Because many of the results and observations reported in the literature have a direct bearing on the results obtained in the present research and form part of the basis for conclusions reached, a brief summary of the findings is necessary. Methods for experimental investigation of hydrogen in liquid steel are comparatively new. The first attempts to estimate the hydrogen content of the open hearth bath were by Kalling and Rudberg,6 who devised a method for collecting gases evolved from the boiling bath of a basic open hearth furnace. They found that the gas during the boil generally contained 2 to 3 pct H2. From this and Sieverts'

Jan 1, 1958

By C. H. Mathewson, J. A. Collins

The process of plastic extension of face-centered cubic single crystalline rods is so well understood, since the notable studies of Taylor and Elam,1 that the change in orientation of any crystal by slip and rotation may be predicted from the measured elongation. It is customary to assume a very homogeneous deformation, wherein gliding lamellar arc free to rotate so that their slip direction continually approaches the axis of the rod, until a second slip system comes into operation; whereupon conjugate slip proceeds quantitatively to an end adjustment with the [121] direction in the axis of the rod. This process has been checked in malty face.-centered cubie materialsand and readily permits the preparation of specimens that have been subjtvted to various determinable amounts of shearing action. It is elearly of interest to study in such measurably strained speeimens the, development of a recrystallized structure on annealing and if possilble detect the source of nuclei from which the new crystals grow. Strain-:~nneali~ig experiments of this charactcr have been performed by others but not in detail sufficient to permit a study, for example, of the number of recrystallized grains vs. the amount of shear. In the experiments now reported, this was done with a wide variety of orientations covering nearly the entire range of slip on a single system and corresponding to amounts of shear (ratio of shearing distance to distance between lamellae at the conclusion of a test of from 0.08 to 0.57. A particular point wa-made of determining the crystallite rotation, or small angular range. assumed by the octahedral slip plane after these various amounts of shear. The, mechanism of reerystallization and the magnitude and effeet of recovery on the recrystallization process was investigated.

Jan 1, 1940

By J. A. Collins, C. H. Mathewson

The process of plastic extension of face-centered cubic single crystalline rods is so well understood, since the notable studies of Taylor and Elam,1 that the change in orientation of any crystal by slip and rotation may be predicted from the measured elongation. It is customary to assume a very homogeneous deformation, wherein gliding lamellar arc free to rotate so that their slip direction continually approaches the axis of the rod, until a second slip system comes into operation; whereupon conjugate slip proceeds quantitatively to an end adjustment with the [121] direction in the axis of the rod. This process has been checked in malty face.-centered cubie materialsand and readily permits the preparation of specimens that have been subjtvted to various determinable amounts of shearing action. It is elearly of interest to study in such measurably strained speeimens the, development of a recrystallized structure on annealing and if possilble detect the source of nuclei from which the new crystals grow. Strain-:~nneali~ig experiments of this charactcr have been performed by others but not in detail sufficient to permit a study, for example, of the number of recrystallized grains vs. the amount of shear. In the experiments now reported, this was done with a wide variety of orientations covering nearly the entire range of slip on a single system and corresponding to amounts of shear (ratio of shearing distance to distance between lamellae at the conclusion of a test of from 0.08 to 0.57. A particular point wa-made of determining the crystallite rotation, or small angular range. assumed by the octahedral slip plane after these various amounts of shear. The, mechanism of reerystallization and the magnitude and effeet of recovery on the recrystallization process was investigated.

Jan 1, 1940

By G. D. Bengough

CORROSION tests should be designed so as to facilitate as far as possible the interpretation of results, consequently factors which may affect the rate of corrosion should be controlled as far as practicable, and very full data should be given regarding the conditions of the test. Among the most important factors affecting the rate of corrosion is often the rate of supply f oxygen to the metal surface. It is essential therefore to understand the mechanism by which oxygen is transferred from the liquid surface to the surface of the metal. The work of Adeney and his coworkers has thrown much light on this mechanism. They have shown1 that the aeration of deaerated water and salt solutions proceeds much more rapidly than can be accounted for by mere diffusion, and have suggested that downward "streaming" takes place from the surface of the water, due mainly to an increase of density brought about by evaporation. The evaporation reduces the temperature of the surface layer, and also increases the concentration in the case f salt solutions. The effect of evaporation in facilitating the transfer of oxygen to a metal and increasing the corrosion f the metal was shown in some experiments due to Friend .2 He tested the corrosion f mild steel plates immersed in water in glass jars, a steady stream f air being drawn over the surface of the water in the jars. The air passing through half the number f jars was saturated with moisture, that passing through the others was dried with calcium chloride. He found that "in every case the water exposed to dry air was approximately twice as corrosive as that exposed to air saturated with water vapor."

Jan 1, 1929

By J. A. Collins

THE process of plastic extension of face-centered cubic single crystal-line rods is so well understood, since the notable studies of Taylor and Elam,1 that the change in orientation of any crystal by slip and rotation may be predicted from the measured elongation. It is customary to assume a very homogeneous deformation, wherein gliding lamellae are free to rotate so that their slip direction continually approaches the axis of the rod, until a second slip system comes into operation; whereupon conjugate slip proceeds quantitatively to an end adjustment with the [112] direction in the axis of the rod. This process has been checked in many face-centered cubic materials and readily permits the preparation of specimens that have been sub-jected to various determinable amounts of shearing action. It is clearly of interest to study in such measurably strained specimens the development of a recrystallized structure on annealing and if possible detect the source of nuclei from which the new crystals grow. Strain-annealing experiments of this character have been performed by others but not in detail sufficient to permit a study, for example, of the number of recrystallized grains vs, the amount of shear. In the experiments now reported, this was done with a wide variety of orientations covering nearly the entire range of slip on a single system and corresponding to amounts of shear (ratio of shearing distance to distance between lamellae) at the conclusion of a test of from 0.08 to 0.57. A particular point was made of determining the crystallite rotation, or small angular range assumed by the octahedral slip plane after these various amounts of shear. The mechanism of recrystallization and the magnitude and effect of recovery on the recrystallization process was investigated.

Jan 1, 1940

By Mark J. Klein

The precipitation of nitrogen in quenched and aged CY-35 at. pct Re was followed by internal-friction and electrical-resistivity measurements. It is shown that the precipitation kinetics of nitrogen from solution are many orders of magnitude lower in this alloy than in chromium. The reluctance of nitrogen to precipitate from sol~ction can be attributed to the composilional r-eadjustnzents required in the z.icinity of a chromium nitrade particle for gowth to occur. AS part of an investigation of the mechanism by which rhenium increases the low-temperature ductility of chromium and other Group VI-A metals, it was of interest to compare the concentration of interstitial elements retained in solution in chromium with that of a ductile Cr-Re alloy. The presence of certain interstitial elements in chromium has been shown to decrease its ductility1-5 and, of these interstitials, nitrogen is believed to have the most detrimental effect on mechanical properties. Thus, a comparison of the disposition of nitrogen in chromium with that in a ductile Cr-Re alloy might provide information about the mechanism whereby rhenium enhances the ductility of chromium. In previous internal-friction studies it was shown that the equilibrium solubilities of nitrogen in chromium and Cr-35 at. pct Re did not differ greatly.= However, results indicated that the actual concentration of nitrogen retained in solution at ambient temperatures is likely to be considerably greater in the alloy than in chromium because the precipitation kinetics of nitrogen are greatly retarded by the addition of rhenium. The objective of this investigation was to study the kinetics of nitrogen precipitation in Cr-35 at. pct Re in greater detail and to obtain information concerning the mechanism of nitrogen precipitation in this alloy. The properties studied were internal friction and

Jan 1, 1967

By Sherwin Kelly

The prime objective of geophysical exploration is to promote the economical and rapid dis-covery of mineral or oil deposits of commercial value. To a few this concept as applied in min-ing may signify the direct discovery of ore-bodies, but to the geophysical engineer this latter Idea is one of the most insidious and detrimental misapprehensions which he has to combat. The destruction of this annoying obstacle to the progress of geophysical exploration reveals the kernel of truth behind it, that the exploration geophysicist has for the better part of two decades been concerned primarily with the discovery of mineral formations favorable to the occur-rence of commercial ore. There is a very real distinction here, since geophysical methods are capable of discovering certain mineral formations such as sulphide bodies or quartz veins, but are totally incompetent to predict whether or not they constitute ore; that is. whether or not they contain minerals of economic value in the amounts requisite to repay extraction. The art of geophysical exploration is now, however, rapidly outgrowing these early limita-tions. The rate of this growth will in large measure depend on the recognition by the mining industry of the fact that geophysics can play a role far wider and more important than it usual-ly does now, in guiding the future exploration and development of mineral deposits. It is my own firm conviction that as time marches on we will see the methods of applied geophysics turned more and more to the delineation of both minor and major structural features. The outlining of such features having a bearing on the probable loci of mineral deposition will be of inestimable value in guiding the development of a mining district. It is in this field that there will In-evitably occur a meeting and overlapping of the activities of the exploration geophysicists and

Jan 1, 1940

By T. A. Rickard

The interior of West Australia is an arid table-land, elevated 1400 feet above the sea. This plateau is flanked to the south by the Tertiary limestones which fringe the Great Australian Bight. It is bordered northward by the Carboniferous beds of the Fitzroy river and westward by the granite of the Darling hills, while to the cast this wide area, about 900 miles square, slopes downward imperceptibly into an undulating plain of sand, which stretches with dismal persistence across the boundary of South Australia. The waters of the ocean receded from this tract of land long ago; it is probably the oldest landsurface on the globe, and represents the basal wreck of a much larger continent. Fig. 1 is a map of this region. The Coolgardie and Kalgoorlie gold-fields are situated in the southwestern part of the region. The rock-formation consists of granite penetrated by diorites and andesites. The latter are occasionally associated with tuff's, which have been readily mistaken for sedimentaries. There are no fossil-bearing rocks, such as would afford a datum-line from which to measure the relative geological age of the prevailing formation. On the extreme edges of the mining territory there are, it is true, remnants of sand-rock which are considered identical with the " Desert Sandstone " of Queensland, determined by Daintree to be of Mesozoic age. But even this formation has evidently been laid down so long subsequent to the underlying rocks that it serves merely to emphasize their much greater antiquity. In their characteristics and in their relations to each other, the granite and the diorite of the Coolgardie region appear to me much to resemble the Laurentian granite and the Huronian

Jan 1, 1899

By Rich Akerman

as 1866, I wish to assure both these gentlemen that I had not seen the section when I designed mine, :md even if I had, I should not have then dared to put it forth as a standard for English rail makers; tind the soundness of my opinion has a simple but conclusive proof in the statement made concerning the extra price which was at that time required for their production. I need not say that I highly approve of the original Welch section, for it is in principle similar to the design which I made ufteen yeam subsequently; and from a professional point of view I would fully concecle to Mr. Welch the credit of first designing the modern steel-rail section. From com- mercial, matter of tict, and practical point of view, he was, however, before his time by many years; or to put it in another way, rail making was ten years behind its time when the new metal steel was first introduced for rails. If his design has been incorrectly identified with my name (as the sections are similar in principle, though they differ in thickness of flange and web), I beg to say (1st) that I much regret the misun- Understanding which has arisen through no fault of niine, aud (2d) that no confusion has been intentionally created by me. It is a pity that the section designed so long ago has not been made public at an earlier date, as it would make a really goal stand- and pattern, anil even now be quite equal to present requirements. In conclusion, I wish to say that I have never desired to claim any invention or novelty by the publication of my sections; they Were put forth as being such as English railmakers could and would produce at the ordinary market. price, and as being the best and most suitable to be so obtained. Had Mr. Welch or Mr. Holley put forward theirs ten or fifteen years ago, I should have been the first to recommend theru. In fact I should have been glad to see their narnes associated with rail patterns in their own country, in the same way as mine has been. PROFESSOR RICH. AKERMAN, STOCKHOLM, SWEDEN: i AGREE with your (Mr. Sandberg's) views that it is too early yet to stipulate only one definite chemical composition in the rails. Such a stipulation, I think, might he justified, if it were not for the manganese; but this metal changes the properties of the iron aud steel in tho same direc- tion ae carbon, silicon. and phosphorus, by increasing its tensile strength, stiffness, hardness, and brittleaess. If the iron and steel does not only contain carbon and manganese but also phosphorus,

Jan 1, 1881

By Richard H. Willey

Efficient handling of large tonnages in open-pit mining demands, primarily, an abundance of well fragmented rock. To accomplish this, a drilling and blasting department composed of a well-knit, versatile group of workers and supervisors must be established. Some costs will remain relatively on the same level over a period of years, while others can be greatly lowered as will be shown. 'The Utah Copper Division, Kennecott Copper Corp., Bingham Canyon, Utah, has been ever alert for improvements in operating methods and equipment to gain increased efficiency and lower costs. Bingham Canyon MIne The greatest dimension of the mine is 8000 ft northeast-southwest with a width of 5000 ft southeast-northwest. From the lowest level, at an elevation of 6040 ft above sea-level, the mountain rises in 27 benches on the west side to W level (elevation 7800 ft) and 21 benches on the east side to Q level (elevation 7460 ft). At the inception of open-pit mining in 1906, the overcapping of leached porphyry had to be removed to reach a commercial grade of sulphide ore. The overcapping or waste now remaining is quartzite with intercalated limestone beds. The limestones are usually soft in nature except in the south-middle portion of the mine where they have been meta-morphized along the contact zone. This area usually gives drilling and blasting operations a great deal of trouble. Here occurs the greatest amount of secondary blasting, as the well-established fracture planes cause the altered beds to break into large boulders. Several massive quartzite "ribs" occur in the overburden, and as a result, the uniform breakage is difficult to obtain. The major quartzite areas have been subjected to complex folding, fracturing and faulting because of the intrusion of the underlying stock. The monzonite porphyry, which carries the commercial values, presents no serious drilling problem because of its softness and extensive minute fracturing throughout the mass. A series of major slips or faults pass through the ore body which, although of considerable advantage to the drilling and blasting department, sometimes works to the disadvantage of the track department. Drilling an11 blasting of the porphyry apparently becomes easier as depth is attained. but highly siliceous streaks throughout the pit still present difficulties. At no place is the rock of such character as to allow excavation without preparations. On certain higher elevations or levels, old fill material can be dug by the shovels, but only at some risk to equipment because of bank slippage. Past Methods At the outset of shovel operations in 1906, drilling was done with the Ingersoll-Rand F-24 piston drill mounted on an un-

Jan 1, 1949

By C. C. Hatch, C. R. Larsen, A. L. Mular

INTRODUCTION As part of a general project to simulate a concentrator, the Brenda Mines Limited secondary crushing plant, located near Peachland, B. C., was sampled during the summer/winter of 1975 and during the summer of 1978 to develop a digital crushing plant simulator specific to the Brenda operation. The purpose of this simulator was to study the influence of manipulable process variables on important responses, to permit study of alternative circuit configurations if desired and to perform off-line optimization. This chapter describes the methodology employed to develop the simulator (1,2) along with typical applications thereof. SECONDARY CRUSHING PLANT FLOWSHEET Figure 1 is a schematic diagram of the Brenda Mines Ltd. secondary crushing plant circuit. The 41,000 tonne coarse ore stockpile(a) is -17.8 cm oversize (3B belt) from two 2.4 m x 6.1 m double deck vibrating screens (not shown). The screens are fed by 2 conveyor belts operated in series with two 198 cm apron feeders that handle discharge from a 152 cm x 226 cm primary gyratory crusher(520 KW). The primary crusher (not shown) treats up to 2725 tonne/hr of run of mine ore. Minus 1.9 cm undersize from the primary screens (#19 belt), referred to as the primary fines, joins secondary screen undersize (#18 belt) for conveyance to fine ore bins (not shown). Feed from the coarse ore stockpile is transferred by means of vibrating feeders and two 120 cm conveyors (#6 and #7) to transfer belts #8 and #9 (Figure 1). The belts feed two secondary 2.1 m standard heavy duty cone crushers (bl and b2). Each crusher is equipped with a modified coarse mantle liner and a standard coarse bowl liner. Mantle throw is 9.2 cm; nominal close side set is 3.2 cm. Crusher .countershafts (443 rpm) are driven by single 260 KW synchronous motors (710 rpm). Discharge from the secondary cone crushers joins discharge from four 2.1 m tertiary heavy duty shorthead cone crushers (fl, f2, f3 and f4). With the exception of the cavity (modified medium mantle liner and standard coarse bowl liner; close side set is nominal .84 cm) and motor (224 KW), these machines are similar to the secondary crushers. The combined discharge is transferred from a 183 cm conveyor to #14 belt which empties into a 1452 tonne secondary screen surge bin (c). Vibrating feeders beneath the bins feed five 2.4 m x 6.1 m double deck vibrating screens (dl, d2, d3, d4 and d5) sloped at 200 from the horizontal. The upper decks are punched plates with 2.7 cm x 7.6 cm slots. Lower decks are woven wire (1.27 cm diameter) sections with

Jan 1, 1982