Search Documents

By O. A. Knight, Helmut Muller-Stock

The suppression of the austenite-martensite transformation that can be brought about by the addition of certain alloying elements, such as manganese or nickel, to plain carbon steel has been known for a long time, especially since Guillet's investigation at the beginning of this century. The extent to which the critical range is lowered depends upon the percentage and nature of the special element added. First the Arl point is lowered gradually, then at a certain percentage a sudden lowering to about 300" C. occurs. The addition of still larger percentages of the alloy may result in lowering the Ar, point to room temperature or below, in which case the steel remains austenitic at room temperature, especially after rapid cooling. The effect of alloying elements of this general type on the lowering of the transformation temperature is well illustrated by Sauveur(lJ$ in his Fig. 281a, reproduced here as Fig. 1. This type of curve is characteristic of both manganese and nickel though it requires about 21/2 times as much nickel as of manganese to produce the same result. The influence of nickel in retarding the transformation of austenite into the lower transition constituents is due to its lowering of the critical range of the steel, which is also well illustrated by Sauveur'l) (after Osmond) in his Fig. 284, reproduced here as Fig. 2. Scott('" presents a diagram illustrating the effect of manganese on the Ac3 and Ara points which is strikingly similar to the diagram above referred to in Fig. 2 concerning the effect of nickel. Lowering the critical range has the effect of increasing the viscosity, or, rigidity, of the alloy at the time when it is undergoing its transformation, which greatly slows down the transformation reaction velocity, and this, in turn, makes it easier to suppress, wholly or in part, the transformational changes. Reaction rates are normally much slower at low

Jan 1, 1934

By M. E. Nicholson

The solid solubility of boron in iron has been determined by saturating iron with respect to FeyB at several temperatures from 870° to 1135 C. In alpha iron the maximum solubility was found to be 0.002 pct B and in gamma iron the solubility varied from 0.001 pct at 915°C to 0.020 pct B at 1165OC. The eutectic and peritectoid temperatures were found to be 1165° and 911 °C respectively and the gamma iron solidus was located approximately at 0.020 pct B. RECENT investigations of boron-treated steels', ' indicate that the solubility of boron in austenite is of the order of 0.003 pct at 900°C. This has led to the general belief that the solubility of boron in a and r iron is considerably less than that indicated by Wever and Muller." Therefore the solid solubilities of boron in a and r iron have been re-determined. The eutectic and peritectoid temperatures were also remeasured and the r-iron solidus was studied in some detail.* In 1929 Wever and Miiller investigated the phase equilibria of Fe-B alloys. Fig. 1 shows the solid solubility region of the Fe-B diagram based on their investigation. They found that boron lowered the A, transformation temperature to 1381 °C where saturated 6 solid solution "which must contain about 0.15 pct B" and "r solid solution containing about 0.10 pct B" are in equilibrium with liquid containing 1.9 pct B. At the eutectic temperature of 1174"C, 7 solid solution was found to contain "about 0.15 pct B." A peritectoid relation was found to exist between a and y iron with an invariant temperature at 915 "C, where the boron solubility in 7 iron was "about 0.10 pct B" and the solid solubility in a iron "did not exceed 0.15 pct B." Although most of their

Jan 1, 1955

By Günter Petzow, Siegfried Steeb

DURING an investigation of the U-Co-A1, U-Ir-A1, and U-Ni-A1 ternary systems, three previously unknown phases have been identified which correspond to the phases UCoA1, UIrA1, and UNiA1, and which be- long to the C22 (Fe2P) type (P 6 2m). In the following the structure determination of the new ternary phases is reported. The alloys have been prepared in an arc furnace under purified argon from 99.97 wt pct U, 99.83 wt pct Co, 99.99 wt pct Al, 99.95 wt pct Ni, and 99.97 wt pct Ir. The pellets obtained were bright and brittle; chemical analyses agreed with the nominal compositions. To obtain equilibrium, the samples were annealed in evacuated quartz capsules at 950°C for 30 hr and then quenched in water. Guinier photographs were processed and evaluated according to a method already described previously.1,2 The hkl's, measured and calculated sin2 6 values, and in the case of UCoAl only calculated and estimated intensities, are given in Tables I to 111. Lattice parameters refined according to the least-squares method and the respective mean-square variations are presented in Table IV. Lattice parameters, especially the c/a ratio, lead to the assumption that the three phases are crystallizing in the C22-type structure. For the calculation of the intensities given in Table I, the atomic positions recently reported by wyckoff3 have been accepted for the C22 (Fe2P) type. The uranium atoms were assumed to be in phosphorus sites; furthermore the scattering amplitudes of the boron atoms have been averaged in the stoichiometric formula UB2 according to atomic percentages; i.e., for these atoms a statistical distribution on the iron sites was assumed. The two smallest distances between a uranium and

Jan 1, 1967

By S. S. Rumsey

Introduction IN order to realize the economies which would result in operating the mine pumps at the Chapin mine with electricity. generated by water power, the Oliver Iron Mining Co. recently installed a hydro-electric plant at the upper Quinnesee, falls on the Menominee river, and constructed a transmission line to the mine. On account of the large flow of water in the Chapin mine, and the great depth from which it has to be handled, it was necessary to make a thorough investigation of the merits of both the motor-driven centrifugal and motor-driven plunger pumps, in order that the most economical results as regards power, cost of installation, maintenance, and operation, be obtained. This investigation resulted in the selection of motor-driven centrifugal pumps, as the cost of the pumps and motors, installation, and maintenance was considerably lower, and the space required in the underground workings very much smaller, than for the plunger pumps. The overall efficiencies guaranteed by several of the centrifugal-pump manufacturers were so nearly those guaranteed by plunger-pump manufacturers that the saving in power which would result from the installation of plunger pumps did not justify their increased first cost and the increased cost of installation under the conditions prevailing at the Chapin nine. In order to substantiate the representations of the centrifugal-pump builders it was deemed necessary to insist upon a factory test of the completed units before shipment, the test to be conducted under conditions of head and capacity approximating as nearly as possible those under which the pumps would operate in service. Furthermore, it was considered necessary to demonstrate, by test, that there were no deficiencies in design or capacity of the pumps or motors before their final installation in the mine, as it would be extremely difficult to make alterations in the pumps or motors after they were installed.

Jan 10, 1914

By C.H. Davis, W.H. Bassett

The ease and value of the application of spectrum analysis to industrial chemistry appears to be appreciated in few of the large works laboratories of this country. For 8 years, this analysis has been of great value to the authors in both analytical and metallurgical work. To the analyst the complete qualitative analysis of an unknown alloy, revealed by a spectrogram, is a sure basis for the planning of the most direct and rapid method of attack. As the determination of each element proceeds, the purity of precipitates may be checked as often as desired. The spectrograph proves invaluable in the recognition of impurities, the separation of which would entail a lengthy and difficult procedure, or when the weight of an unknown is less than is necessary to complete the desired determinations. A few hundredths of a gram will usually suffice for spectrographic analysis. In the separation of the rarer elements, the spectrograph will show, with precision, the point where each step has been successful. In zinc of certain classes, indium, gallium, and germanium have been isolated in this way; the presence of antimony in lake coppers has been proved; and bismuth has been detected in zinc and in alloys where the presence of a few thousandths of a per cent. would be harmful. An antimony precipitate in a delicate determination may contain a considerable proportion of tin or arsenic, both of which will be revealed. The spectrograph is consequently important to the metallurgist as well as to the analyst. Impurities in raw material are often a source of annoyance, especially when their detection involves delay and costly analytical work. Whethcr low conductivity in copper is due to arsenic, nickel, or something else may be cluickly found out. Residual traces of boron, magnesium, manganese, silicon, vanadium, and other deoxidizing agents are easily identified where wet analysis may fail to reveal their presence, even after days of effort. Complex alloys of any kind are dissociated by the spectro-

Jan 1, 1923

By W. H. Bassett, C. H. Davis

The ease and value of the application of spectrum analysis to industrial chemistry appears to be appreciated in few of the large works laboratories of this country. For 8 years, this analysis has been of great value to the authors in both analytical and metallurgical work. To the analyst the complete qualitative analysis of an unknown alloy, revealed by a spectrogram, is a sure basis for the planning of the most direct and rapid method of attack. As the determination of each element proceeds, the purity of precipitates may be checked as often as desired. The spectrograph proves invaluable in the recognition of impurities, the separation of which would entail a lengthy and difficult procedure, or when the weight of an unknown is less than is necessary to complete the desired determinations. A few hundredths of a gram will usually suffice for spectrographic analysis. In the separation of the rarer elements, the spectrograph will show, with precision, the point where each step has been successful. In zinc of certain classes, indium, gallium, and germanium have been isolated in this way; the presence of antimony in lake coppers has been proved; and bismuth has been detected in zinc and in alloys where the presence of a few thousandths of a per cent. would be harmful. An antimony precipitate in a delicate determination may contain a considerable proportion of tin or arsenic, both of which will be revealed. The spectrograph is consequently important to the metallurgist as well as to the analyst. Impurities in raw material are often a source of annoyance, especially when their detection involves delay and costly analytical work. Whethcr low conductivity in copper is due to arsenic, nickel, or something else may be cluickly found out. Residual traces of boron, magnesium, manganese, silicon, vanadium, and other deoxidizing agents are easily identified where wet analysis may fail to reveal their presence, even after days of effort. Complex alloys of any kind are dissociated by the spectro-

Jan 1, 1923

By H. A. Coy

THE Mascot mines of the American Zinc Co. of Tennessee are situated in the Holston River valley, in Knox County, Tennessee, about 13 miles (20.9 km.) east of the city of Knoxville, and form a property of three operating shafts and one open pit. A second open pit is located at Jefferson City about 16 miles (25.8 km.) east of the Mascot mines. Geology Topography.-The principal topographical features of the region within which the zinc deposits occur is a series of parallel northeast and. southwest ridges which reach altitudes of 200 to 400 ft. (61 to 122 m.) above the valley. These ridges are formed of resistant formation such as sandstone, quartzites, etc., while the valleys are occupied principally by limestone, including Knox dolomite, and by shale and other formations subject to quick erosion. The Holston River valley is wide and open with a rolling surface. Sink holes are common to the limestone portion, the general aspect of the valley being that of well-rounded hills with low intervening valleys superimposed upon which is a characteristic sink-hole topography. General Geology.-According to Keith, the rock formation of the area extends from the lower Cambrian into the Silurian. The region has undergone severe deformation with heavy faulting, the underlying Cambrian having been brought to the surface by a series of low angle thrust faults, the strike of the faults and formations paralleling the general northeast and southwest direction of the topography and clipping at varying angles to the southeast. In general the Cambrian quartzites, sandstone, etc., occupy the ridges while the Cambro-Silurian dolomites, limestone and shales occur principally in the valleys. Of the latter, the Knox dolomite is of particular interest to this paper in that it is the ore carrier in the Mascot area. The ore is associated with more or less irregular breccia zones, the degree of brecciation varying from-a fine crushing to a breaking that involves blocks of large size. The breccia zones

Jan 9, 1917

By H. A. Coy, H. B. Henegar

The Mascot mines of the American Zinc Co. of Tennessee are situated in the Holston River valley, in Knox County, Tennessee, about 13 miles (20.9 km.) east of the city of Knoxville, and form a property of three operating shafts and one open pit. A second open pit is located at Jefferson City about 16 miles (25.8 km.) east of the Mascot mines. Geology Topography.—The principal topographical features of the region within which the zinc deposits occur is a series of parallel northeast and southwest ridges which reach altitudes of 200 to 400 ft. (61 to 122 m.) above the valley. These ridges are formed of resistant formation such as sandstone, quartzites, etc., while the valleys are occupied principally by limestone, including Knox dolomite, and by shale and other formations subject to quick erosion. The Holston River valley is wide and open with a rolling surface. Sink holes are common to the limestone portion, the general aspect of the valley being that of well-rounded hills with low intervening valleys superimposed upon which is a characteristic sink-hole topography. General Geology.—According to Keith, the rock formation of the area extends from the lower Cambrian into the Silurian. The region has undergone severe deformation with hcavy faulting, the underlying Cambrian having been brought to the surface by a series of low angle thrust faults, the strike of the faults and formations paralleling the general northeast and southwest direction of the topography and dipping at varying angles to the southeast. In general, the Cambrian quartzites, sandstone, etc., occupy the ridges while the Cambro-Si urian dolomites, limestone and shales occur principally in the valleys. Of the latter, the Knox dolomite is of particular interest to this paper in that it is the ore carrier in the Mascot area. The ore is associated with more or less irregular breccia zones, the degree of brecciation varying from a fine crushing to a breaking that involves blocks of large size. The breccia zones

Jan 1, 1918

By E. O. Jones, E. Whitehead

During the heating of cold-worked nickel silver, the tendcncy of the material to crack is well known. The present research deals with this question, and may conveniently be divided into the following sections: Changes in these alloys during heating and cooling, determination of the temperature at which cracking occurs, effect of grain size, quenching cracks, methods of overcoming annealing cracking. The work is far from complete, in particular the influence of impurities on this tendency has not been investigated, but the results so far obtained lead to certain definite conclusions, which are of theoretical and practical importance. Changes in Alloys During Heating and Cooling During the annealing of many metals at a temperature just below that at which recrystallization sets in, there is evidence of some change, the effect of which is to harden and embrittle the material. This effect has been most clearly demonstrated in the cases of aluminum, copper, brass, and nickel silver, and appears to be a common property of cold-worked metals and alloys, or, at any rate, the non-ferrous ones. The effect would obviously offer an explanation for certain types of annealing cracking, but the trouble is so much more common in the nickel silvers than in the other alloys that some special cause should be looked for. There is, however, fairly good reason for believing that similar cracking may occur in some of the brasses; D. Bunting1 suggests that the a brasses toward the saturation limit are subject to a transformation closely allied in nature to that known to occur in the nickel silvers at around 320" C. Although the existence of this critical temperature range was known, it did not necessarily follow that this transformation was responsible for the trouble under investigation, so the first portion of this paper deals with the attempts made to determine whether other critical changes might not occur in these alloys. There were already reasons for the belief that such would prove to be the case, as the mechanical properties of the nickel

Jan 1, 1926

By E. O. Jones

DURING the heating of cold-worked nickel silver, the tendency of the material to crack is well known. The present research deals with this question, and may conveniently be divided into the following sections: Changes in these alloys during heating and cooling, determination of the temperature at which cracking occurs, effect of grain size, quenching cracks, methods of overcoming annealing cracking. The work is far from complete, in particular the influence of impurities on this tendency has not been investigated, but the results so far obtained lead to certain definite conclusions, which are of theoretical and practical importance. CHANGES IN ALLOYS DURING HEATING AND COOLING During the annealing of many metals at a temperature just below that at which recrystallization sets in, there is evidence of some change, the effect of which is to harden and embrittle the material. This effect has been most clearly demonstrated in the cases of aluminum, copper, brass, and nickel silver, and appears to be a common property of cold-worked metals and alloys, or, at any rate, the non-ferrous ones. The effect would obviously offer an explanation for certain types of annealing cracking, but the trouble is so much more common in the nickel silvers than in the other alloys that some special cause should be looked for. There is, however, fairly good reason for believing that similar cracking may occur in some of the brasses; D. Bunting suggests that the a brasses toward the saturation limit are subject to a transformation closely allied in nature to that known to occur in the nickel silvers at around 320° C. Although the existence of this critical temperature range was known, it did not necessarily follow that this transformation was responsible for the trouble under investigation, so the first portion of this paper deals with the attempts made to determine whether other critical changes might not occur in these alloys. There were already reasons for the belief that such would prove to be the case, as the mechanical properties of the nickel

Jan 7, 1925

By E. A. Trager, A. W. McCoy, H. R. Shidel

Sampling of the fluid from oil wells for percentages of oil, emulsified oil, and water during the last two years has brought out some interesting facts concerning oil-water emulsion. This result led to a laboratory investigation of emulsion, which substantiated the conclusions made from the field observations. The purpose of this paper is to present the information collected, the laboratory experiments, and our interpretation of the same. In order to define emulsified .oil exactly, give its synthesis and origin, and to show how and when it is formed in the wells, the work was necessarily divided into two separate lines—laboratory work and field observations. It is hoped that this study may lead to a discussion of such points so that the petroleum engineer, geologist, or technologist may be benefited by its practical bearing on oil-field management. Special credit is due Mr. Everett Carpenter, chief geologist of the Empire Gas & Fuel Co., for his assistance and cooperation in this work. Labobatory Investigations on Emulsified Oil Laboratory investigations were conducted in an attempt to learn the composition and some of the properties of emulsified oil, or B. S., as it is more commonly called, also to demonstrate, by laboratory methods, how B. 5. may be formed under conditions similar to those existing at the time a well is being pumped, and how it may be broken down. Literature bearing on this subject is widely scattered and very limited in scope. Bacon and Hamor define B. S., or bottom settlings, as "earthy matter, inert organic matter, or, in the case of Pennsylvanian petroleum, an emulsion of paraffin wax and water, which accompanies crude oil." In this discussion we will limit the term B. S. to that heavy, dark-brown emulsion, composed of a physical mixture of water, oil, and air with some included inert matter, either organic or inorganic. Possibly the first step in a description of this product should be a description of its physical properties, but since most operators are quite

Jan 1, 1921

By Francis C. Krauskopf, Carl E. Swartz

Metallurgists differ considerably in their opinions regarding the effect, if any, of small amounts of iron pyrites, or other iron compounds on zinc sulfide ores during the roasting operation. As a result, the literature on this subject expresses many conflicting ideas. The ore, previously crushed to pass through a 1-mm. screen, dries in the roasting kiln, losing water up to 200° to 300° C. At 150° C. iron pyrites begin to lose sulfur. As the temperature increases, while the ore is passing to the hotter part of the furnace, the sulfur burns to sulfur dioxide, leaving the metals as zinc oxide and ferric oxide. These two substances then interact to form zinc ferrite, a compound, yellow brown in color, having the general characteristics of a spinel. Like magnetite, another spinel, zinc ferrite is insoluble in alkalis and dilute acids. As a result, when leached with 10 per cent. sulfuric acid solution, zinc values tied up in this compound remain behind History In the electrolytic recovery of zinc from its ores, the roasted ores are usually leached with a 10 per cent. sulfuric acid solution. When the zinc ore contains iron pyrites as an impurity in an appreciable amount, the actual yield of metallic zinc is much lower than a theoretical calculation would indicate. Further, losses of zinc are, in a rough way, directly proportional to the amount of iron pyrites or other iron compounds present. When the iron is present in the ore in an isomorphous relation to the zinc, as in the case of a marmatite, a greater amount of zinc remains insoluble than when present as a true pyrite or marcasite. Work on the insoluble residues obtained from leaching of the calcines shows that the zinc lost is intimately tied up in this residue. Some investigators have suggested a definite compound, such as zinc ferrite; others merely a mixture of zinc and iron compounds. As early as 1851, Pelouze(')' prepared calcium ferrite by fusion of calcium oxide and ferric oxide. Ebelman, 2) about the same time, prepared

Jan 1, 1928

By Carl Swartz

METALLURGISTS differ considerably in their opinions regarding the effect, if any, of small amounts of iron pyrites, or other iron compounds on zinc sulfide ores during the roasting operation. As a result, the literature on this subject expresses many conflicting ideas. The ore, previously crushed to pass through a one-millimeter screen, dries in the roasting kiln, losing water up to 200° to 300° C. At 150° C. iron pyrites begin to lose sulfur. As the temperature increases, while the ore is passing to the hotter part of the furnace, the sulfur burns to sulfur dioxide, leaving the metals as zinc oxide and ferric oxide. These two substances then interact to form zinc ferrite, a compound, yellow brown in, color, having the general characteristics of a spinet Like magnetite, another spinel, zinc ferrite is insoluble in alkalis and dilute acids. As a result, when leached with 10 per cent. sulfuric acid solution zinc values tied up in this compound remain behind. HISTORY In the electrolytic recovery of zinc from its ores, the roasted ores are usually leached with a 10 per cent. sulfuric acid solution. When the zinc ore contains iron pyrites as an impurity in an appreciable amount, the actual yield of metallic zinc is much lower than a theoretical calculation would indicate. Further, losses of zinc are, in a rough way, directly proportional to the amount of iron pyrites or other iron compounds present. When the iron is present in the ore in an isomorphous relation to the zinc, as in the case of a marmatite, a greater amount of zinc remains insoluble than when present as a true pyrite or marcasite. Work on the insoluble residues obtained from leaching of the calcines shows that the zinc lost is intimately tied up in this residue. Some investigators have suggested a definite compound, such as zinc ferrite, others merely a mixture of zinc and iron compounds.

Jan 1, 1927

By R. V. Lundquist

Leaching manganese-bearing materials with NaOH to remove caustic-soluble silica has been demonstrated as a method for up- grading manganese. Those materials containing opaline varieties of silica respond most readily. Spent leach liquors are regenerated by treatment with lime to precipitate calcium silicate and to reactivate the NaOH for leaching.

Jan 4, 1953

By J. E. Schiller, S. E. Khalafalla

Due to its unique surface properties, magnesium oxide (MgO) is an excellent medium to filter asbestos and other suspended solids from water. MgO operates up to twice as long as a sand filter before backwashing is required while flow rate and filtrate clarity are as good or better with MgO.

Jan 1, 1984

By A. Tobey Yu

The recent adverse economic climate has added further impetus to the demand for better-grade and lower-cost raw materials, for which increasingly larger quantities of muck are being moved and processed at higher unit labor costs. As a result, the cost impact of handling and shipping has never been as keenly felt by the mining industry as it is today. Thanks to joint innovative efforts by users and manufacturers, new and improved automated bulk-handling systems and devices are now blossoming everywhere to give the mining man the tools he needs to move ore, waste and concentrates more efficiently and economically.

Jan 1, 1970

By Charles O. Thomson

When a wire rod of iron or of steel is immersed in a hot solution of common salt, allowed to remain long enough to bring the metal to the temperature of the brine, and withdrawn, the surface of the rod is irregularly covered with a deposit of crystals of salt. These crystals adhere to the cod with great firmnes, in consequence, doubtless, of a thin film of ferric hydrate, which is formed between them and the rod as the water dries off. The rod can now be reduced, by successive passes through a dic or draw-plate, without any

Jan 1, 1881

By Walter Weeks

THE process of cooling air by allowing it to expand and do work in an engine is well known, but the theory of obtaining cold air by free expansion without the aid of an engine operating with cutoff has been little discussed. CASE I If compressed air is allowed to expand to the atmospheric pressure through an orifice in an air line that is supplied by a running compressor, no cooling results except the negligible one due to the Joule-Thompson effect, which will not be considered in this discussion. The effect of moisture will also be neglected.

Jan 1, 1937

By R. C. Gifkins

The ideas expressed in this paper interest me very greatly, partly for their own sake and partly because they are very close to some speculation I have recently made concerning grain boundary diffusion. This is in a paper describing an extension to Mott's "island" theory of the grain boundary, to be published shortly.37 The facets or islands of good fit are identified in terms of specific crystallography, as in the model put forward by Brandon et al., and the bad fit between them is suggested to be interlinked "channels" of relaxed vacancies, associated with grain boundary ledges.

Jan 1, 1969

By H. Van F. Furman

There has been considerable discussion of late as to the best method of determining the silver-contents of sulphides of silver resulting from the leaching of silver-ores, and also as to the relative merits of the crucible- and the scorification-method for the determination of the silver-contents of ores. Owing to the great depression in the silver-market, these are questions of considerable importance, at the present time, to both the producer and the smelter and refiner. In the hope of throwing some further light on this subject, the following experiments were recently made by the writer:

Jan 1, 1896