Search Documents

By F. L. Holderreed

A choosy in what they would smelt. The furnace charge had to be coarse, and it had to be rich. They discarded fines in excess of about 1/10 the total weight. They wanted 10% copper content and fussed about anything with as low as 5%. They concentrated the copper content of the charge as much as they could by prior selection. They roasted off enough sulfur to further enrich the copper content of the succeeding fall of matte (a melt of cuprous and ferrous sulfides or Cu2S.FeS). Then they desulfurized the iron and fluxed it by carefully adding silica (quartz, not silicates) for a slag of lower density than the cuprous sulfide (Cu2S or white metal). After skimming off the slag, they further desulfurized the white metal by blowing the molten bath with compressed air. The result was blister copper. Yesterday Their techniques and furnaces? Some experimented with mechanically rabbled roasters, but their standard roasting practice was burning coarse sulfide ore in 250-ton heaps. These heaps, approximately 24 x 24 x 6 ft, were burned for about 75 days down to 6-10% sulfur. The turnaround time for a given roasting position was 100 days. Assuming the base was a hearth, the calculated rate of treatment was on the order of 0.004 tpd per sq ft.

Jan 1, 1971

By P. T. Gallagher, W. A. Oates

THE partial excess entropy of interstitial solutes in metals, SXS , has usually been interpreted as being principally vibrational ever since the initial statistical treatment of hydrogen in metals by Fowler and Smith-ells. The vibrational entropy is considered being due to the optical modes of the light interstitial atom. Little attention has been given to the magnitudes of the values of SXS'. Leiser and Witte2 and Ebisuzaki and O'Keeffe3 have noted that for hydrogen in metals Si is approximately constant for different metals. On the other hand if it is assumed that the interstitial solute is an isotopic defect then, as shown by McLellan, SXS should vary from metal to metal as follows: where S is the standard entropy of the solvent and Mi, M, are the masses of the interstitial and solvent atoms. respectively. Fair agreement with this equation was found for oxygen in silver and nitrogen in iron4 and for carbon in iron.= Ln a subsequent analysis of metal- hdrogen systems McLellan' found a variation of $' from metal to metal but not in a manner expected from the isotopic impurity equation. However, a possible correlation between the energy of solution, Ei, and sf was noted. Similar correlations have been noted for certain dilute substitutional solid Solutions 7, 8 and recently Kubaschewski 9 has demonstrated a correlation between integral heats and ex-

Jan 1, 1970

By Harrison Souder

In view of the proposed visit of the Institute to Cuba this winter, the following brief sketch of the principal mineral deposits near Santiago de Cuba has been prepared largely from notes taken in February, 1903, during a visit to the mines then in operation in the province of Santiago de Cuba. Westward from Cape Maysi, the most eastern point of the island, the coast is rocky and uninviting. The usual course of the steamers is well in toward the shore, and the lines of stratification of the rocks can be distinguished clearly, the presence of iron or other ores being indicated by frequent blotches of mineral stain. One is impressed with the general rugged character of the southeastern coast-line,—an almost unbroken barrier of coral-limestone bluff's, full of caves and hollows, into which the surf rushes with a roar and bursts into tall fountains of spray. Beyond rises abruptly the Sierra Maestra range, whose sharp, peaked crest-line betrays its eruptive or igneous origin. From a height of about 800 ft. near Cape Maysi, this range gradually rises to the westward, attaining its maximum elevation of more than 8,300 ft. in the Pico Turquino, beyond Santiago. A general resemblance to the mountain-ranges of southern New Mexico is noticeable. At Daiquiri, 20 miles east of Santiago harbor, the extensive

Jan 1, 1905

By J. J. Kantner

CREEP investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that applica-tion of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and struc-tural character of the solid metal.

Jan 1, 1937

By Frank W. Clinard, Oleg D. Sherby

The effect of multiple an transformations on diffusion in a dilute iron alloy was studied. Inter-penetration between iron and an Fe-Co alloy was evaluated, under thermal-cycling conditions chosen so as to transform only the iron-rich side of the diffusion couple. It is shown that a small but consistent diffusion enhancement by a factor of two results when data from the transforming side of thermally cycled specimens are compared with predicted inter diffusion coefficients based on isothermal data. No enhancement is found when data from the mntransforming side of such couples are compared with predicted diffusivities. It is suggested that short-circuiting by moving pain boundaries is the most likely mechanism contributing to the observed diffusion enhancement from multiple phase transJormations in iron. Transformation-induced Point defects, dislocation-pifie short-circuiting, and point defects generated by dislocation motion are less effective in contributing to enhanced diffusion under the experimental conditions utilized. SO far as is known, no studies have been made of the effect of allotropic transformation on diffusion. previous to this investigation. Studies have been made, however, of the influence of transformation on the diffusion-controlled processes of spheroidization and sintering. Cullen1 has described a method of accelerating spheroidization in an AISI 1030 steel. Partial transformation between a and ? phases was uti-

Jan 1, 1965

By C. V. Millikan, Herbert F. Beardmore

Declining Productivity Index, as considered herein, is a productivity index that has a substantially and consistently decreasing value when measured over a period of a few hours. If not recognized, it may be interpreted as representing an unsettled or unstable condition in a producing well. It forms the basis of a number of predictions as to future performance compared with the performance of wells in which the productivity index does not decline. The nost important of these are that: (I) the rate of oil production will decline more rapidly, (2) the gas-oil ratio will usually increase abnormally, (3) the amount of water ultimately produced will be negligible, if any, (4) stop-cocking will increase current production and decrease gas-oil ratio. When such relative well performance is indicated, it follows that certain reservoir performance and operating practices may be anticipated: (I) disappointing recovery, (2) longer natural flow, (3) no active water drive, (4) better evaluation of acidizing, shooting and reworking, (5) intermittent operation of wells, (6) smaller pumping equipment required. It is significant that the basis of these important predictions is bottom-hole pressure tests that can be made immediately after completion of the wells. Introduction "'Productivity index" is the number of barrels of oil produced per day per pound per square inch of differential pressure between the reservoir and the bottom of the well. "Declining Productivity Index," as considered herein, is a productivity index that has a substantially and consistently decreasing value when measured over a period of a few hours. Productivity index can be determined only when the rate of production can be stabilized. In most wells the rate of production and bottom-hole pressure are easily stabilized to give a constant productivity index for a period of many hours. A few produce so erratically as to preclude probability of an acceptable test in the usual sense. A satisfactory productivity index can be determined in some wells only by gauging the production accurately by hours, measuring the bottom-hole pressure continuously, and from these data calculating the productivity index for successive hours. Such figures frequently will have a decreasing value—that is, a declining productivity index—and when plotted on double. logarithmic cross-section paper with productivity index as ordinate and time as abscissa will be a straight-line curve. The angle between the curve and the abscissa is referred to as the rate of decline. Declining productivity index may appear to be the result of change in permeability to oil due to decreasing saturation of oil and increasing saturation of gas in the reservoir. It is possible that such is in fact the cause, but if so, more is involved than merely relative saturation of oil and gas. This seems evident because the rate of decline in productivity index is substantially the same regardless of the pro-

Jan 1, 1945

By William Klement

THIS note reports the results of some attempts to metastably extend the primary solid solubilities of tin, antimony, and silicon in silver by rapidly quenching these binary alloys from the melt. The procedures employed for alloy preparation, quenching, and Debye-Scherrer X-ray diffraction measurements have been described elsewhere. The lattice parameters obtained for the fcc structures in Ag-Sn and Ag-Sb alloys are presented in Fig. 1, together with the results of Owen and Roberts.4 Alloy compositions are believed to be within ± 0.2 at. pct on the basis of negligible weight losses during preparation and reproducibility of the lattice spacings. Diffraction lines from hcp phases were also detected: the relative visual intensities of the fcc (200) and hcp (10.2) lines were estimated as shown in Table I. The intensities were m for the (200) and w for the (10.2) in a quenched 13.6 at. pct Sn alloy: a lattice spacing for the fcc structure could not be reliably obtained, however. As seen from Fig. 1, the lattice parameters vary linearly with composition up to 8., at. pct Sb and 13." at. pct Sn, respectively, which may be compared with the maximum equilibrium solid solubilities5 of 7.2 at. pct Sb and 11.5 at. pct Sn, respectively. The presence of the hcp phases, which were found together with the fcc phases, is a consequence of the competition1,3 in the nucleation and growth processes during solidification. Both the fcc and hcp phases must be of the same composition for those alloys in the range where lattice parameters increase linearly with solute concentration. Despite much effort with quenched alloys of several silicon concentrations, it has not been possible to obtain lattice spacings of sufficient precision to establish the variation of lattice parameter with composition or the maximum metastable solid solubility: the equilibrium data5 suggest little primary solid solubility of silicon in silver. For alloys containing less than 16 at. pct Si, the Si (111) diffraction line was not observed. For alloys containing 10 to 25 at. pct Si, faint low-angle lines were detected and these could be indexed as the (10.0), (00.2). and (10.1) reflections of an hcp structure with a = 2.87 + 3A. c = 4.52 ± 3A, and c/a = 1.57 ± 2. The 16 at. pct Si alloy was quenched to, and examined at. liquid nitrogen temperatures without any change observed in the proportion of the hcp phase. These experiments were jointly supported by the Atomic Energy Commission and Office of Naval Research under a program directed by Professor P. Duwez. The assistance of H.-L. Luo and A. Abu-Shumays is acknowledged. as is the support afforded

Jan 1, 1965

By R. P. Carreker, J. G. Leschen, J. H. Hollomon

The external appearance of a crystal which has undergone plastic flow suggests that adjacent blocks of the crystal have glided bodily past one another along the slip planes. However, the great discrepancy between the shear stresses calculated to effect such a movement and those actually observed has for many years stimulated searches for more satisfactory interpretations of the slip process. Appreciable success in these efforts has been realized by assuming the presence in the crystal of various sorts of imperfections and by considering the consequences of the presence of these flaws when stress is externally applied. The theory that has received the most attention recently—that of dislocations—postulates the occurrence of small, mobile imperfections or dislocations which move through the crystal along the slip direction, each dislocation being attended by a local shear displacement of one interatomic distance. Thus only that portion of the crystal through which the dislocation has passed may be said to have slipped. Since each dislocation produces a displacement of only one interatomic distance, an avalanche or train of many dislocations would be necessary to account for the observed displacements of several hundred or thousand interatomic distances. The salient point of the theory of dislocations is the concept that a slip band does not suddenly appear in its entirety. On the contrary, it grows progressively across the slip plane as the individual dislocations successively appear and advance in a train through the crystal. However, the concept of growth is not intrinsic only to the theory of dislocations, since atomistic mechanisms other than that postulated by the dislocation theory can quite probably also describe the growth of a slip band. For instance, a slip band might resemble a disc-like interface that appeared and then grew continuously from a small size, producing a displacement that increased with the size of the disc. Whatever the precise mechanism, the concept of growth is in itself consistent both with the observed low values of critical shear stress and with the experimental observation that slip bands frequently do not traverse the entire crystal. The likelihood that slip bands grow implies that they must first be nucleated and that the initiation of slip can therefore be analyzed in terms of the general concepts of nucleation. Indeed, this suggestion was advanced1 several years ago, but the matter does not appear to have been further pursued. Recent advances in the theory of nucleation 2,3,4 have encouraged such a treatment of the slip process. As will presently be demonstrated, this approach to the problem not only accounts successfully for the incubation periods that have been observed 5,6 to precede slip but also predicts certain transient effects in the deformation process. The existence of these transients apparently has not hitherto

Jan 1, 1949

By R. P. Carreker, J. G. Leschen, J. H. Hollomon

THE external appearance of a crystal which has undergone plastic flow suggests that adjacent blocks of the crystal have glided bodily past one another along the slip planes. However, the great discrepancy between the shear stresses calculated to effect such a movement and those actually observed has for many years stimulated searches for more satisfactory interpretations of the slip process. Appreciable success in these efforts has been realized by assuming the presence in the crystal of various sorts of imperfections and by considering the consequences of the presence of these flaws when stress is externally applied, The theory that has received the most attention recently-that of dislocations-postulates the occurrence of small, mobile imperfections or dislocations which move through the crystal along the slip direction, each dislocation being attended by a local shear displacement of one interatomic distance. Thus only that portion of the crystal through which the dislocation has passed may be said to have slipped, Since each dislocation produces a displacement of only one interatomic distance, an avalanche or train of many dislocations would be necessary to account for the observed displacements of several hundred or thousand interatomic distances. The salient point of the theory of dislocations is the concept that a slip band does not suddenly appear in its entirety. On the contrary, it grows progressively across the slip plane as the individual dislocations successively appear and advance in a train through the crystal. However, the concept of growth is not intrinsic only to the theory of dislocations, since atomistic mechanisms other than that postulated by the dislocation theory can quite probably also describe the growth of a slip band. For instance, a slip band might resemble a disc-like interface that appeared and then grew continuously from a small size, producing a displacement that increased with the size of the disc, Whatever the precise mechanism, the concept of growth is in itself consistent both with -the observed low values of critical shear stress and with the experimental observation that slip bands. frequently do not traverse the entire crystal. The likelihood that slip bands grow implies that they must first be nucleated and that the initiation of slip can therefore be analyzed in terms of the general concepts of nucleation. Indeed, this suggestion was advanced1 several years ago, but the matter does not appear to have been further pursued. Recent advances in the theory of nucleations2,3,4 have encouraged such a treatment of the slip process. As will presently be demonstrated, this approach to the problem not only accounts successfully for the incubation periods that have been observed5,6 to precede slip but also predicts certain transient effects in the deformation process, The existence of these transients apparently has not hitherto

Jan 1, 1948

By R. Schuhmann, O. W. Moles

at temperatures of 1150°, 1250°, and 1350°C for liquid copper sulphides ranging in composition from saturation with Cu to about 21.5 pct S. From the experimental data, activities of Cu, S, and Cu2S in the melts were calculated. Also, the results furnish a new determination of the location of the curve showing the compositions of Cu-saturoted sulphide melts in the CU-S constitution diagram. THE "white metal" made as an intermediate L product in converting copper matte to blister copper is a matte approximating Cu2S in composition. It has long been known that liquid Cu-S mattes can exist at a given temperature over an appreciable composition range, with S:Cu ratios ranging up from a lower limit corresponding to equilibrium of the matte with a liquid Cu phase. The Cu-saturated matte has somewhat less S than Cu2S, although previous measurements of the compositions of Cu-saturated mattes are not in good agreement.'" As the S:Cu ratio approaches and slightly exceeds that for Cu2S, the partial pressure of sulphur gas over the liquid matte rapidly approaches atmospheric pressure,5 so that Cu-S melts with much more S than Cu2S can be made and handled only in pressure apparatus. Accordingly, the liquid copper sulphides of interest in copper smelting and readily studied experimentally fall in a relatively narrow composi- tion range about Cu2S. The freezing points of Cu-S mattes show a maximum of 1129°C near the composition Cu, dropping to 1105oC for Cu-saturated mattes having less S and dropping under 1100°C for higher S mattes.' Estimates of the sulphur pressure and other thermodynamic properties of liquid Cu,S were made by Kelley; based on extrapolations from equilibrium measurements on solid Cu,S. More recently, Cox and coworkers' studied equilibria in the reaction: Cu,S + H, e 2Cu + H,S over the temperature range 700" to 1250°C. They measured equilibrium H2S:H2 ratios presumably with both the sulphide and the metal phase present, so that their data above the melting point of Cu,S should measure the S pressure of Cu-saturated sulphide melts. The sulphur pressures of liquid copper sulphides of several S:Cu ratios at their freezing points can be estimated from data given by Posnjak, Allen, and Merwin." However, beyond these few data, no systematic study seems to have been made of the relations of sulphur pressure and other chemical properties of liquid copper sulphides to composition and temperature. The measurements of the sulphur pressures of liquid copper sulphides reported in this paper represent a first step in the quantitative study of the chemistry of mattes. Similar work is planned on

Jan 1, 1952

By M. G. Arthur

This paper is a theoretical analysis of fingering of water and coning of water and gas in homogeneous sand. Investigation of this idealized case illustrates the relative magnitude of the factors involved in actual conditions. The body of the report presents equations, example calculations, and charts that facilitate solution of such problems. Derivation of the equations introduced in this paper and a discussion of previously published equations are included in the appendix. Introduction Production of water from oil wells as a result of the pressure gradients established by flow of fluids through oil-~roducing sands is a common occurrence, which influences the cost of oil production, the degree of depletion and the efficiency of expulsion of oil from naturally occurring reservoirs. Control of water production and encroachment are important both in primary and secondary phases of of exploitation in order to produce oil and gas at lowest cost and in order to achieve the greatest ultimate recovery of the oil in the reservoir. Although many actual oil reservoirs present a multitude of variables that influence fingering and coning of water and gas, an inspection of the relationship and magnitude of the forces involved in the case of a homogeneous sand may indicate satisfactory methods of controlling water production. Application of equations relating the variables may indicate the geometric type of drainage that exists in a particular reservoir or in the vicinity of a particular well. A homogeneous sand body is assumed within the portion of the reservoir influenced by the well. Two geometric types of drainage are considered theoretically. The first is water fingering into an oil sand that is relatively thin compared with the lateral extent of the sand. This sand may represent the entire oil-producing reservoir or it may represent one interval in an oil reservoir, which is separated from other producing intervals by competent lithologic barriers to flow of fluids. For the condition of complete penetration of a well in such a sand body, it may be assumed that no flow occurs across bedding planes. A mathematical relation is developed between the limit of approach of a water finger to the well without being drawn into the well and the corresponding operating pressure drawdown. The second condition considered is that of water or gas entry into an oil well as the result of coning through bedding planes. The theory and graphical solution developed by Muskat' for the limit of approach of a water or gas cone to a well, without its entry into the well, related to the corresponding maximum pressure drawdown, is reviewed and amplified, Charts are presented, which facilitate graphical solution of the problem. A method is presented for the extension of this type of graphical solution to the case where gas and water coning occurs simultaneously~

Jan 1, 1944

By M. G. Arthur

This paper is a theoretical analysis of fingering of water and coning of water and gas in homogeneous sand. Investigation of this idealized case illustrates the relative magnitude of the factors involved in actual conditions. The body of the report presents equations, example calculations, and charts that facilitate solution of such problems. Derivation of the equations introduced in this paper and a discussion of previously published equations are included in the appendix. Introduction Production of water from oil wells as a result of the pressure gradients established by flow of fluids through oil-~roducing sands is a common occurrence, which influences the cost of oil production, the degree of depletion and the efficiency of expulsion of oil from naturally occurring reservoirs. Control of water production and encroachment are important both in primary and secondary phases of of exploitation in order to produce oil and gas at lowest cost and in order to achieve the greatest ultimate recovery of the oil in the reservoir. Although many actual oil reservoirs present a multitude of variables that influence fingering and coning of water and gas, an inspection of the relationship and magnitude of the forces involved in the case of a homogeneous sand may indicate satisfactory methods of controlling water production. Application of equations relating the variables may indicate the geometric type of drainage that exists in a particular reservoir or in the vicinity of a particular well. A homogeneous sand body is assumed within the portion of the reservoir influenced by the well. Two geometric types of drainage are considered theoretically. The first is water fingering into an oil sand that is relatively thin compared with the lateral extent of the sand. This sand may represent the entire oil-producing reservoir or it may represent one interval in an oil reservoir, which is separated from other producing intervals by competent lithologic barriers to flow of fluids. For the condition of complete penetration of a well in such a sand body, it may be assumed that no flow occurs across bedding planes. A mathematical relation is developed between the limit of approach of a water finger to the well without being drawn into the well and the corresponding operating pressure drawdown. The second condition considered is that of water or gas entry into an oil well as the result of coning through bedding planes. The theory and graphical solution developed by Muskat' for the limit of approach of a water or gas cone to a well, without its entry into the well, related to the corresponding maximum pressure drawdown, is reviewed and amplified, Charts are presented, which facilitate graphical solution of the problem. A method is presented for the extension of this type of graphical solution to the case where gas and water coning occurs simultaneously~

Jan 1, 1944

By G. E. Goodspeed

THE Cornucopia gold quartz veins form a parallel vein system traversing metamorphic and granodioritic rocks. Field and petrographic evidence suggests that metasomatism has played an important role both in the emplacement of the granodiorite and in the formation of the veins. Structurally the veins appear to be related to the major tectonic features of the Wallowa Mountains and to be narrow shear zones rather than filled fissures. Petrographic studies indicate a complex history of formation starting from initial alteration along fractures or joints followed by recurrent fracturing and a quartz-forming stage, and closing with continued shearing and microbrecciation, which permitted the upward percolation of the later ore- forming solutions. The precipitation of ore minerals from these solutions formed ore shoots. Postmineral effects include the injection of Tertiary basaltic dikes, a slight amount of cross faulting, and some movement along the planes of the veins as well as oxidation.

Jan 1, 1939

Year of Election 1959 Andrew Fletcher, New York, N Y "For his outstanding leadership in the lead and zinc mining industries, and for his able and devoted services to the Institute as its Treasurer and President, and as a Director for many years " 1917 Herbert Hoover, New York, N Y 1955 George M Humphrey, Cleveland, Ohio 1950 Zay Jeffries, Ptttsfield, Mass 1942 Essington Lewis, Melbourne, Vic, Australia 1959 John M Lovejoy, New York, N Y "For his distinguished service to the Institute, for his outstanding contributions in furthering the professional status of petroleum engineers, for his pioneering in application of engineering to petroleum production, and for his outstanding record of public service on behalf of the petroleum industry " 1957 Donald H McLaughlin, San Francisco, California 1957 C H Mathewson, New Haven, Connecticut 1938 Albert M Portevin, Parts, France 1957 Fred Searls, Jr, New York, N Y

Jan 1, 1960

Members of the American Institute of Mining and Metallurgica Engineers can now secure copies of the Journal of the Institute of Metals of Great Britain at a special price of $5 for the two volumes issued during the year, postage extra amounting to approximately 25 cents. This Journal is one of the best books dealing with the subject of non-ferrous metals and alloys and this arrangement with the Institute of Metals permits our members to take advantage of this specially low price. Back numbers of the Journal can be purchased on the same basis. The Journal can be ordered directly through the office of the Institute of Metals, Great Britain 36 Victoria St., Westminster, S. W. I., London, England. The letter should be accompanied by an international money order and a copy sent to Secretary of the A. I. M. E. in order that the membership record may be checked.

Jan 9, 1919

INTERNATIONAL ENGINEERING CONGRESS This Congress will be held under the auspices of five National Engineering Societies, of whi h the Institute is one. The sessions will be held in 11 sections and the proceedings will be published in 10 volumes of 500 pages each, of which Volume 8 will contain the papers and proceedings on Mining Engineering and Metallurgy. The membership fee of $5 will entitle the holder to the volume of General Proceedings and Index, and, in addition thereto, any other single volume chosen. Other volumes may be subscribed for according to a sliding scale depending upon the number of volumes taken. The Institute will have a meeting in San Francisco during 1915, and it is desirable for our members to join the International Engineering Congress at in early date in order that their support of the enterprise may be given in its early stages, when it is most needed.

Jan 2, 1914

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Oct. to Nov. 10, 1915: Lester S. Thompson, New York, N. Y. Arthur L. Sweetser, Boston, Mass. William Reed, El Oro, Mexico. Dorsey A. Lyon, Salt Lake City, Utah Heinrich Ries, Ithaca, N. Y. D. W. Blaylock has resigned his position with the St. Joseph Lead Co., Bonne Terre, Mo., and has accepted the position of division engineer for the Big Creek Coal Co., of Chicago, at Harrisburg, Ill. R. B. Lamb announces the removal of his office to Room 1809, 43 Exchange Place, New York, N. Y. C. C. Sanders has taken a bond and lease on the Red Mountain group of 34 mining claims (copper), Patagonia, Ariz., and has commenced extensive development.

Jan 12, 1915

One Hundred Sixteenth Meeting of the Institute, Monday, Feb. 18, to Thursday, Feb. 21, inclusive, 1918. Committee on Arrangements J. E. JOHNSON, JR., Chairman BRADLEY STOUGHTON, Vice-Chairman A. R. LEDOUX J. V. N. DORR L. W. FRANCIS F. T. RUBIDGE G. D. VAN ARSDALE MRS. S. J. JENNINGS E. M. SHIPP RALPH W. DEACON ARTHUR L. WALKER The program for the New York Meeting, in February, 1918, as planned by the Committee on Arrangements at meetings in the middle of December, and therefore subject to slight alteration in detail, is as follows: MONDAY, FEBRUARY 18 9 a. m. to 5 p. m. Registration at Institute Headquarters. 10 a. In. Technical Sessions. 12.30 p. in. Luncheon at Engineering Societies' Building. 2 p. m. : Technical Sessions. 8.30 p. m. War Smoker or Patriotic Meeting. TUESDAY, FEBRUARY 19 10 a.m. Annual Business Meeting, followed by Technical Sessions.

Jan 1, 1918

A special meeting of the Board of Directors was held on July 25, 1916, pursuant to notice duly given according to the By-Laws. This special meeting was for the purpose of giving authority for the signing of a contract with the American Society of Civil Engineers, as mentioned in another place in this Bulletin. The interest in the matter is indicated by the attendance of 11 members of the Board, some of whom came from a long distance. An invitation was received from the St. Louis Section of the Institute and from members in and near St. Louis to hold the 115th Meeting of the Institute in and near St. Louis in late September or early October, 1917. This invitation was accepted. Announcement was made that the Mexican Institute of Mining and Metallurgy had been dissolved and reorganized as the Mexican Section of the Institute.

Jan 9, 1916

By L. A. Wright, J. F. Emerson

The Pine Creek mine, owned by Union Carbide Nuclear Co., Div. of Union Carbide and Carbon Corp., is one of the world's largest producers of tungsten. The mine is located on the eastern slope of the Sierra Nevada Mountains, about 25 miles north- west of Bishop, Calif. Prior to 1948, production from the property came either from surface pits or from underground workings above A level haulage tunnel. The tunnel is at an elevation of 10,900 ft, which left 500 to 600 ft of vertical backs to the surface outcrops. Heavy production demands during World War II hastened the planning for long range development of orebodies below A level. A 7000-ft haulage tunnel, 1500 ft below A level, was started in 1943 and completed in early 1947. This haulage tunnel is at an elevation of 9400 ft and is known as Zero tunnel.

Apr 1, 1956