Search Documents

By Ralph H. Sweetser

C. H. Herty, Jr.,* Pittsburgh, Pa.—The procedure of the Open-hearth Committee in studying pig iron and its effects in the open hearth has been influenced by the discussions at a number of meetings of the Committee. Those discussions have brought out very clearly that, as far as the pig iron affects the quality, interference with quality should be studied for three definite types of pig iron: (1) low-silicon pig iron; (2) very high-silicon pig iron, and (3) pig iron in which the silicon varies over a wide range in short periods, such as 1 to 3 casts. If a blast furnace is running steadily at 1 per cent. silicon iron, practically no trouble, apparently, can be traced to the pig iron, but if the furnace is running from 0.60 up to 1.50 and then down to 0.60 per cent., trouble in the finished steel is liable to occur, which apparently cannot be corrected by open-hearth practice. The open-hearth discussions have shown fairly definitely that with low-silicon iron, one type of trouble arises on the finished product and with the high-silicon iron, another. Our experience with the high-silicon is that any non-metallic matter that may form, does so when the pig iron is put into the furnace; that is, silicates immediately form which are more liable to be high in silica than would happen with low-silicon iron. I think Mr. Sweetser will agree with mc that if a blast furnace is very irregular, different points in the furnace may be working irregularly, in other words, the temperature gradient all over the furnace is not uniform. We have made many determinations on that point which indicate that a varying blast furnace causes hot spots and cold spots around the periphery. If some of those spots are hot and others are cold, although the analysis of the iron may be constant, then unreduced oxide, going through on one side, and good iron, going through on the other, may mix and the average temperature of the iron is not high enough to get completely rid of the oxides. So our method of attack is directly on that point; it is our first objective. Our procedure is to make a number of consecutive tests at a blast furnace, making a detailed study of the blast-furnace operation. We follow the iron through the open-hearth heat, being sure that we know just how much of each kind of iron gets into the open hearth, and take out specified samples at certain times during the process, working on steel where no finishing additions are made in the furnace. We are following one type of iron through the billet mills and into the finished product and are obtaining complete data on open-hearth operation. Besides the ordinary chemical analyses on the samples of slag and metal, we are running samples of the plg iron, the steel in the open hearth and the finished steel, for oxygen and silicates. We are going to find out whether or not oxygen, as silicates or oxides, has some connection with this trouble. If not, we may be able to locate some other factor. I am inclined to think that the silicates are responsible, judging from the indications in some other work that the Bureau of Mines is doing in Pittsburgh. We have laid out a very definite method of testing to which we will adhere at the different plants where we are now working and at others in the future. Our aim is to

Jan 1, 1927

By Michael G. Schill, Mark C. Fischer

Since its introduction several years ago in the United States, the high pressure belt filter press has proven to be a highly cost-effective dewatering device in a number of mining and industrial applications. To evaluate the process and economic factors associated with the dewatering of coal refuse, a comprehensive program of laboratory and on-site pilot studies has been conducted. This paper will summarize findings of this study and discuss advantages of the belt filter press over conventional dewatering methods. The conventional means of dewatering thickened coal refuse involves the use of vacuum disc filters or centrifuges. Due to the high amount of energy used to dewater refuse with these devices it was a logical course of action to apply belt filter press technology to this application, since a belt filter press will require less than 3.7 kW (connected).

Jan 1, 1982

By Gordon H. Geiger, J. Bruce Wagner

Electrical conductavity and therrnoelectvic nzeasuretnents on synthetic hematite slabs with 0.01 to 0.90 at. pet Ti and with 0.30 at. pet Ca were made. Additions of titanium and of calcium both increased the electronic conductivity with titanium yielding greater n-type behavior and calciurn p-type behavior. Reduction studies of hematite to magnetite in CO-CO2 atmospheres between 600° and 900°C initially exhibited linear kinetics. These linear rates were increased by additions of titanium and decreased by calcium. IN recent years many studies have been reported in the literature on the kinetics of the reduction of hematite and magnetite to iron. In addition, Hansen and Josephl and Schenck and Schultz2 have reported studies on the reduction of hematite to magnetite, the first step in total reduction to iron. In order to evaluate the results of the studies of over-all reduction in terms of the actual mechanism of the reaction and to define further the important factors in the rate- controlling mechanism of the magnetic roasting reaction, the following experiments were undertaken. Specimens of undoped hematite and hematite containing titanium or calcium in solution as doping agents were reduced to magnetite in CO-CO2 mixtures. In addition, electrical-conductivity measurements were correlated with the reduction kinetics using concepts of defect solid-state chemistry. EXPERIMENTAL Fisher certified Fe2O3 powder was used to make specimens for both the electrical and kinetic studies (see Table I for analysis). Doping with titanium and calcium was accomplished by adding TiO2 and CaO powders to the Fe2O3 powder. The powders were mixed in a Waring blender for minimum times of 1/2 hr. Satisfactory blending was achieved based on comparison of analyses of individual specimens af- ter reduction. The specimens were formed in a steel die using opposed punches with a rectangular opening 10.0 by 40.0 mm. The Fe2O3-TiO, platelets were pressed cold at 16,000 psi. They were sintered for approximately 16 hr at 1075°C in air, in accordance with information in the literature3, 4 on the time and temperature needed to obtain solution of the titanium in the hematite. The Fe2O3-CaO mixtures were first cold-pressed at 20,000 psi and sintered for 3 hr at 1225°C to insure solution of CaO. This material was then ground to -325 mesh in a 6-in. ball mill and the resulting powder was used to make platelets in the same manner as above. The sintered platelets were usually between 1/16 and 1/8 in. thick. They were ground on a carborundum wheel and polished on 2/0 paper. Typical dimensions of the kinetic-study specimens were 1.6 by 0.8 by 0.05 cm, and a typical weight was 0.3 g. Conductivity and thermoelectric specimens were approximately the same size, but were subjected to further sintering in order to ensure maximum densification. Finally, all specimens were measured to the nearest 0.0005 in. and weighed on a Mettler H-15 balance to the nearest 0.0001 g and the density calculated. The average density of the specimens used for the reduction studies was 4.87 g per cc, or 7.1 pet total porosity. The standard deviation ranged from 0.14 to 0.063 g per cc within a composition group. In the present study, the apparent surface area as measured with a micrometer was taken as the true surface area. The chemical analyses for calcium and for titanium within a group showed maximum variations of 50.04 pet from the average values used in Figs. 9 and 11. In order to suspend the specimen from the balance for the kinetic studies, a hole, 0.03 in. in

Jan 1, 1965

By AIME AIME

AMERICAN participation in the World Engineering Congress in Japan will be generous. Nearly seventy papers have been prepared and for- warded for printing and the A. I. M. E. is well represented in the list. At our San Francisco meeting four of these will be briefly reviewed by the authors for the benefit of those who are unable to go on to Tokyo. They constitute a group dealing with the present economic status as seen by engineers of the world's iron, coal, petroleum and non-ferrous metals. Messrs. Leith, Smith and Tryon, Requa, and Probert have written papers that constitute a notable series. Messrs. Jeffries, Sweetser and Kinney, and other Institute members have written papers dealing more closely with technologic progress. The latest list of delegates and members is printed below, names of A. I. M. E. members being set in italics.

Jan 1, 1929

By R. D. Reiswig

An increasing amount of high-temperature metall~?~gical research is carried out in resistively heated tube furnaces in which a bare specimen is suspended by a fine wire at the midpoint of the tube. It is shown that the assumption of near-blackbody conditions on the surface of the sample may give rise to errors in optical pyrometry of 50°C or more. A number of papers published in the metallurgical literature in recent years have described the use of high-temperature tube furnaces for heat treatments, melting-point determinations, and other work. Typically, the tube is of a refractory metal with open ends, is heated by the passage of an electric current, and has concentric cylindrical radiation shields outside it. In at least one of these,' the specimen is contained within a crucible having a small hole in its lid through which optical-pyrometer measurements are made under essentially blackbody conditions. In another design,* the specimen is inside a muffle which is concentric with the heater tube and which contains a number of washerlike longitudinal radi- ation shields to reduce axial temperature gradients and to give conditions near the specimen closer to those of a black cavity. Yet another design3 employs a wire specimen coaxial with the heater tube. Blackbody conditions are simulated by passing current from a separate supply through the wire until it "disappears" against the background (the inside of the heater tube) as seen through a radial spy hole in the tube. Good agreement with known melting points is achieved when an optical pyrometer is used under such disappearance conditions as the melting point is approached. That this latter method works so well is due, evidently, to considerations such as those mentioned by Dike4 and others.5-8 A more common method than the above, however, has been the suspension of an uncovered specimen by a fine wire in a resistively heated tube with open ends. A radial spy hole about midway between the ends of the tube permits optical-pyrometer observations on the specimen, the inside of the tube, or both. So observed, the specimen typically appears to differ but little in brightness temperature from the inside of the tube. According to De vos9 the radiation from such a spy hole in an empty tube of reasonable 1ength:diameter ratio (e.g., 10 or greater) should be essentially blackbody radiation. For these reasons, apparently, descriptions of work carried out in such furnaces usually include a statement to the effect that conditions surrounding

Jan 1, 1964

By Francis M. Walters

IN spite of the war and the preoccupation of many physical metallurgists with work on secret or confidential problems, definite progress was made during 1944 in our understanding of the behavior of steel and of the effect of alloying elements. During the first two years of the war there was much concern over the possible unavailability of certain alloying elements; this period saw the development of the N.E. (National Emergency) steels. However, the measures taken eased the alloy situation and currently, highly practical problems under study are the graphitization of low-carbon steel and weld-cracking, while investigations of more theoretical interest have concerned hardenability, isothermal reactions, the effect of hydrogen and the interpretation of the notched-bar impact test.

Jan 1, 1945

By Daniel C. Jackling

WHAT is written here features some of the things that I would say if I were to de- liver a Presidential address during the Annual Meeting to be held this month in New York. I am aware that custom favors written rather than vocal delivery of such a discourse; and, as this accords exactly with my own preference, I assure readers that they will never be called upon to hear these remarks spoken- anyhow, not by me. My year as President is drawing to a close. As I look back I like to classify and analyze the impressions that have been left with me. It has been a delightful and fascinating experience to me personally; I have appreciated the courtesies and aids, and have been deeply gratified at the honors accorded me. Perhaps the source of greatest satisfaction is the opportunity I have had to sense more about the provinces of this Institute and about the useful functions of the profession that it represents. For 38 years I have been a member. I served two terms as Director-one in 1914-'16 and again in 1927-'29. I have been honored by selection as a Saunders Medalist. I thought I was reasonably familiar with the functions, the ideals, and the activities of the Institute. But the things that I have discerned during the past year have dispelled that conceit. I still think that, a year ago, I was as well informed as most members; but since then I have had the rare privilege of executive service and insight. That has given me a perspective that I feel can be obtained in no other way-as I think the illustrious engineers who have preceded me in office will agree. I wish that I had the power to translate to every member somewhat of the feelings of pride in our organization that a year as President cannot help but instill.

Jan 1, 1939

By K. A. Jackson, J. D. Hunt

A new classification of eutectics is proposed, based on tlze entvopies of wzelting of the tuio eutectic phases. The clnssification was used to predict suitable tvansparent analogs of the metallic systems. Experimental confir?nation loas obtained for the theovetical shape of the lamellar solid-liquid interface, fov the fault mechanisms of lanzellar spacing changes, and for the development of low-energy solid-solid boundaries between the lamellae. An explanation is presented to account jov the irvegular and coinplex regular structures zrhich are found in some eritectic systems. FrOM experimental observations, single-phase materials can be divided into two groups according to their solidification characteristics, those that grow as faceted crystals and those that do not. acksonl' showed from thermodynamic reasoning that the type of growth depended on a factor a which was almost thg entropy of melting. Most nonmetals have high entropies of melting (a greater than 2) and grow with crystalline facets. Most metals have low entropies of melting (CY less than 2) and grow almost isotropically with no facets. The authors propose that eutectics may be classified in a similar manner. There are three groups of eutectics, those in which both phases have low entropies of melting, those in which one phase has a high and the other phase has a low entropy of melting, and those in which both phases have high entropies of melting. Lamellar or rodlike structures are formed in systems in which both phases have low entropies of melting. In these alloys dendrites of either phase may be formed, when the alloy is rich in the relevant component. Examples are Pb-Sn, Sn-Cd, Pb-Cd, Sn-Zn, Al-Zn. Irregular, Fig. 14((), or complex regular, Fig. 14(b), structures are formed in alloys in which one phase has a high entropy of melting and the other has a low entropy of melting. Examples are A1-Si, Zn-MgzZnll, Pb-Bi, Sn-Bi. When the alloys are rich in the low entropy of melting phase, dendrites are formed; when the alloys are rich in the high entropy of melting phase, faceted primary crystals are produced. These crystals are sometimes called hoppers or pseudodendrites. In this work the term dendrite will only be used to describe nonfaceted primary crystals. Dendrites are not formed during solidification in high entropy of melting single-phase materials. The third group of eutectics includes alloys in which both phases have high entropies of melting. Each phase grows with a faceted solid-liquid interface. Since most metals do not have high entropies of melting, metallic examples in this eutectic group are rare. However they may occur between some intermetallics and semiconductors or semimetals such as silicon, germanium, and bismuth. Attempts have been made to study eutectic solidification visually by watching the growth process.374 Since metals are not transparent, the observations had to be made on external surfaces. This difficulty can be overcome by using transparent analogs of the metallic systems. As was mentioned earlier, most single-phase compounds have entropies of melting greater than 2 and so grow as faceted crystals. Recently organic materials with entropies of melting less than 2 were investigated.' These materials grow in exactly the same way as the low entropy of melting metals. When the materials are pure, they grow with a solid-liquid interface parallel to an isotherm; when they are impure, cells or dendrites are formed. Since these materials are transparent, have low melting points, and even have cubic structures, they should be ideal for making up transparent analogs of the metallic eutectics. The purpose of the present work was to investigate these organic eutectics and to see whether this quite different series of eutectics could be classified in the same way as the metallic systems. The observations made on the organic alloys are also discussed with reference to the current theories of lamellar growth. Explanations are proposed to account for the structures formed in the other eutectic groups. EXPERIMENTAL Thin cells containing the organic alloys were uni-direction ally solidified on a specially constructed microscope stage.' Uniform growth rates were obtained by moving the cells, with a motor drive, through a fixed temperature gradient, so that the solid-liquid interface remained stationary with respect to the microscope objective lens. The cells were made by fusing two microscope cover slides 7/8 by 7/8 by 1/100 in. together on three sides, leaving a gap of 1 to 3 mils between the slides, and these were filled by surface tension. A preliminary investigation of the phase diagram between two components could be made very rapidly. One side of the cell was filled with component A and the other side with component B. Since only a small amount of mixing could occur every composition from pure A to pure B was present in the cell. When the cell was placed in the temperature gradient a pictorial representation of the phase diagram was obtained. Eutectics, peritectics, "interorganics", and solid -solid transformations could be readily detected. Fig. 1 shows part of a eutectic phase diagram. The Sample was first grown slowly then stopped. The two

Jan 1, 1967

By D. A Dahlstrom

THE necessity for slime elimination from valuable mineral and coal products has become increasingly significant within the past 5 years.' , Most of the mechanized mining and present beneficiation methods have resulted in larger tonnages of extreme fines, silts, and clay, commonly called slimes, processed by the preparation plant. Economics in turn have forced the plant operator constantly to lower the bottom size of effective beneficiation, necessitating an almost complete recovery of valuable solids regardless of particle size. When these important factors are considered, the need for an efficient slime removal method for fine solids becomes self-evident. Ordinarily slimes have been classified as ranging from 75 microns, or 200 mesh, down to colloidal dimensions of less than one micron. At the same time there is general agreement that the most troublesome slimes are primarily clays, silts and extreme fines, so that the actual top size may be placed at approximately 30 to 40 microns. This immediately restricts any desliming operation to classification, as screening or other methods would be both uneconomical and grossly inefficient at such dimensions. The liquid-solid cyclone has been recognized as one of the most efficient fine size classifiers available to the mining industry. Applications of cyclones to thickening, high efficiency solid recovery, degritting,

Jan 1, 1953

By D. A. Dahlstrom

THE necessity for slime elimination from valuable mineral and coal products has become increasingly significant within the past 5 years.' , Most of the mechanized mining and present beneficiation methods have resulted in larger tonnages of extreme fines, silts, and clay, commonly called slimes, processed by the preparation plant. Economics in turn have forced the plant operator constantly to lower the bottom size of effective beneficiation, necessitating an almost complete recovery of valuable solids regardless of particle size. When these important factors are considered, the need for an efficient slime removal method for fine solids becomes self-evident. Ordinarily slimes have been classified as ranging from 75 microns, or 200 mesh, down to colloidal dimensions of less than one micron. At the same time there is general agreement that the most troublesome slimes are primarily clays, silts and extreme fines, so that the actual top size may be placed at approximately 30 to 40 microns. This immediately restricts any desliming operation to classification, as screening or other methods would be both uneconomical and grossly inefficient at such dimensions. The liquid-solid cyclone has been recognized as one of the most efficient fine size classifiers available to the mining industry. Applications of cyclones to thickening, high efficiency solid recovery, degritting,

Jan 1, 1953

By L. E. Tanner

A study was made of the transformation kinetics of the commercial titanium-base alloys, Ti-2.5Al-16V and Ti-4A1-3Mo-1V, using two different heat treatment cycles: 1) step-quenching to aging temperatures from a ß solution anneal and 2) water-quenching from an a+ß solution anneal followed by reheating to aging temperatures. Metallographic examination and hardness testing provided the major portion of the data, while electrical resistivity, dynamic elastic modulus, and X-ray diffraction techniques were also used to obtain critical or confirnzatory data. TTT diagrams were constructed from these results. The sheet alloys, Ti-2.5Al-16V and Ti-4Al-3Mo-lV, are of current interest to the Department of Defense. As an aid to the planning of their respective heat treatments, a program was carried out to determine the transformation kinetics of these alloys using ß and a + ß reference states. This paper presents the TTT diagrams constructed from data obtained by metallographic examination and hardness testing, as well as by X-ray diffraction, electrical resistivity, and dynamic elastic modulus determinations. EXPERIMENTAL PROCEDURE Materials—Sheets of the alloys were obtained from the producers in the "mill anneal'' condition and were tested prior to shipment to assure their meeting mill specifications. Chemical analyses were also supplied and are presented in Table I. Heat Treatment—The majority of the data presented in this study were obtained from hardness testing and metallographic examination. Sample coupons were cut from the alloy sheets and heat treated on a mass scale. The annealing cycles were operated in the following manner: 1) The ß solution anneals were carried out in a horizontal tube furnace with the bare samples protected by a dynamic helium atmosphere. Following this treatment, the samples were quickly transferred to lead, solder, or oil-bath furnaces for aging. After prescribed times at the various reaction temperatures they were water-quenched. 2) The second cycle simulated commercial practice, which requires the alloys be quenched to room temperature following the a + ß sotution anneal. This anneal was carried out in a muffle furnace with a dynamic helium atmosphere. The specimens were then reheated from room temperature to the reaction temperatures in lead, solder, or oil-bath furnaces, followed by water-quenching after prescribed times at these temperatures. Information concerning the critical temperatures of the alloys was obtained from the literature and solution treatments were based on these values. A summary of the solution annealing treatments is found in Tables II and 111. The aging temperatures for the (a - ß alloys ranged in 50°C intervals from 200°C (392oF) to approximately 50°C below the ß/a + ß transus in the first cycle and approximately 50°C below the a + ß solution temperature in the second. The transformations in these alloys were known to be rather rapid, and thus aging times started at 0.5 min and went to a maximum of 7000 min. Hardness Testing and Metallographic Preparation— Heat-treated samples were sheared and mounted in Bakelite with their cut edges exposed. After a flat surface was ground, the hardness was determined in Vpn on an Armstrong-Vickers machine utilizing a 20-kg load. Three to four impressions were made on each specimen. After this procedure, the hardness impressions were removed and the edge surfaces of the specimens were prepared for metallographic examination in the usual manner. The etchant was 20 pct HF and 20 pct HNO3 in glycerine. Electrical Resistivity—It has been shown that the isothermal reactions in titanium-base alloys can be followed by measuring the changes in e1etrical resistivity attending these transformations. As mentioned earlier, the reaction kinetics of a-ß alloys are rather rapid; thus, it would be expected that resistivity data obtained from these alloys would be more significant if measurements were made continuously at the respective aging temperatures. To accomplish this end a special apparatus, based on the current-potential principle, was assembled. Its design was derived from earlier devices constructed by Colner and zmeska1 4 and Levinson.5 The set-up provided for the heat treatment zof machined specimens (approximately 2 x l0-4in. in cross section by 3 in. in length) and the determination of their relative

Jan 1, 1962

By J. W. Freeman, J. P. Rowe, R. F. Decker

HEAT-to-heat variations in properties of an alloy of constant nominal chemical composition have been a perplexing problem to the metallurgist. These heat-to-heat differences have been especially baffling in high-temperature metallurgy. In order to establish fundamental reasons for these heat-to-heat variations, the National Advisory Committee for Aeronautics has sponsored and financially assisted an extended research program on heat-resistant alloys at the University of Michigan. As part of the program to find the contribution of processing variables, Frey, Freeman, and white' studied effects of heat treating on nickel-base alloys and Ewing and reeman' investigated effects of hot-working practice on N155 alloy. To extend the program to the study of effects of melting practice on high-temperature properties, a 55 Ni-20 Cr-15 Co-4 Mo-3 Ti-3 pct A1 composition was selected for experimentation. The objective of this program was to establish the melting-practice variables which influenced the hot-working characteristics and creep-rupture properties and, at the same time, establish the metallurgical mechanisms for the effects. During the course of the investigation of practices using vacuum melting, it became increasingly evident through chemical analyses supplied by industrial concerns that a major variable was melt reaction with the crucible. This paper is devoted to the results of this phase of the melting-practice study. EXPERIMENTAL PROCEDURES Experimental 10-lb heats were induction melted in the University of Michigan vacuum-melting unit with the melting practices outlined in Table I. Aim analysis for the basic alloy, in wt pct, for all heats was as follows: Cr Co Mo Ti Al 20.0 15.0 4.0 3.1 3.1 Mn Si C Ni 0.12 0.12 0.08-0.15 Bal. Small amounts of boron and zirconium were added to certain heats as listed in Table I. These additions

Jan 1, 1959

By Robert C. Linares

Cubic zinc sulfide has been grown from molten salt solutions substantially below the hexagonal-cubic phase transition of 1020°C. Crystals free of birefringence have been grown from molten lead chloride at temperatures from 500° to 800°C. Factors affecting the optical transmission and the birefringence are discussed. CUBIC zinc sulfide is of interest for electrooptic devices and as an optical coating material. However, it cannot readily be produced as large crystals which are free of birefringence. The birefringence arises from the fact that the cubic ZnS is usually grown as the high-temperature hexagonal phase and is transformed to the lower cubic phase by annealing.' This results in stacking faults, stress, and birefringence. A requirement for the growth of cubic ZnS is that it be grown below the phase transition of 1020°C.2 Crystals of cubic ZnS have been grown below 1020°C by the hydrothermal,3 flux,4 and vapor transport5 techniques. However, these all appear to have limitations in size or quality of material produced. It was felt that a new flux method might have a good chance of overcoming some of the previous problems. Mita6 reported the growth of hexagonal ZnS from molten NaCl and wilke7 reported the growth of iron sulfides from molten lead chloride solution, indicating that molten chlorides make good solvents for sulfides. An investigation of a number of possible molten chlorides as solvents showed that molten PbCl2 has an appreciable solubility for zinc sulfide and that crystals can be grown at temperatures from 500° to 800°C. EXPERIMENTAL Crystal growth was performed in open or sealed Vycor or fused silica tubes, in an argon atmosphere or vacuum. There were no deleterious effects due to using vacuum; however, a sealed essentially isothermal system must be used to prevent vapor transport mechanisms from dominating. This will be discussed later in detail. Noble metal containers were not usable as they were severely attacked by these melts. The materials used were: reagent-grade PbC12, reagent-grade ZnS, optical-coating-grade ZnS, and Irtran 2 (ZnS). Crystal growth was accomplished by both slow cooling techniques and gradient growth techniques. In the slow cooling techniques, 15 g of ZnS and 100 g of PbCl2 were used. The components were placed in the silica tube, heated at 800°C for 2 hr, and then slowly cooled (l° to 10° C per hr) to 500°C. The furnace was constructed so that the tube could be inverted, thus allowing the liquid to drain off the crystals at the end of the run. The gradient runs were made by placing the above mixtures in a silica tube at 550° to 600°c, Fig. 1. A temperature gradient was maintained such that the floating mass of undissolved sulfide was 10° to 50°C warmer than the bottom of the tube. Growth occurred on spontaneously nucleated sites at the cooler bottom. RESULTS When using high cooling rates (5° to 10°C per hr), crystals form in thin sheets perpendicular to the {111} face. Crystals 5 by 5 by 1.2 mm, Fig. 2, have been ob-

Jan 1, 1969

By B. D. Lichter

In a previous paper, Oelsen, Schuermann, and Hey-nertl pointed out the possibility of obtaining complete thermodynamic functions for alloy systems from calorimetric measurements alone. Specifically, if the heat content of a heterogeneous, multicomponent system is known as a function of temperature and composition, then it is possible to derive the heats, entropies, and free energies of formation of liquid phases and of solid intermediate phases of fixed composition. The authors present equations and graphical techniques applicable to eutectic systems and systems with intermediate phases without solid solubility at lower temperatures. eijering has considered possible extension of the treatment to systems with complete solid-state miscibility at lower temperatures; however, experimental difficulties practically restrict the method to systems with very limited miscibility in the solid state. The purpose of this note is to present an alternative derivation of the heats and entropies of formation of liquid phases and of solid intermediate phases from heat-content measurements alone. Fig. 1 shows three types of phase diagram to which the analysis may be applied. If the heat content is determined as a function of composition x, at temperature T, we have quite generally and the heat of mixing of the liquid is obtained directly from heat-content measurements. If the temperature T lies in a two-phase region (solid-liquid) then

Jan 1, 1967

By R. S. McBride

The fertilizer industry is a meeting place of mining, manufacturing and agriculture. It is an industry of dynamic change, huge tonnages, and great aggregate value. In the United States from 5,000,000 to 8,000,000 tons of fertilizer are made and used per year, with a value at the works of from $200,000,000 to $300,000,000. The world uses about 50,000,000 tons yearly with an aggregate value between two-thirds and one billion dollars. This world output contains of the essential plant-food constituents, nitrogen, phosphate, and potash, approximately 8,000,000 tons. The corresponding United States quantity, as nearly as can be estimated, is 1,400,000 tons of plant food per year in the aggregate tonnage of fertilizer. With the steady increase in the practice of scientific agriculture throughout the world there has been a corresponding growth in the consumption of fertilizers. In the United States there has, indeed, been but a small upward trend in the tonnage sold, measured in millions of tons of all classes of goods which are made and marketed. The real growth has come through the increasing concentration of the essential plant foods in the mixture. Thus it is estimated that between 1920 and 1930, although there was little increase in tonnage of fertilizer, there was an increase of fully 30 per cent in the content of nitrogen, phosphate, and potash. Hence, the American farmer has actually been using more plant-food to

Jan 1, 1932

By J. V. Richards

The Altar district, State of Sonora, Mexico, is for the most part a desert with but little rain-fall and few running streams. On account of this scarcity of water it is necessary for the natives to " dry-wash" the placer-gravel, and the object of the present gaper is to describe some of the more commoil Mexican dry-mashing devices. My observations were confined to a property known as Las Palomas placers, 15 miles from the Gulf of California and about 150 miles south of the United States border; a brief description of which property may be of interest as illustrating what is, perhaps, a typical Sonora dry placer. It is said that as long as a century ago the Yaqui Indians discovered rich cement-gravel, known as argo masa, at Las Palomas, and that there has been a more or less steady production of gold from the property ever since. The argo masa, is a fairly-coarse gravel, the pebbles being quite firmly held together with a lime cement. Gold is scattered through this cement in particles ranging from fine specks to pieces several grams in weight, and occasional large nuggets are encountered. The contents vary so widely that it is difficult to estimate the average value, but returns of from $10 to $50 per cubic yard are common, and it is doubtful if the Indians considered anything less than from $4 to $5 a yard as "pay dirt.'' This ar-90 masa, occurs in channels varying in thickness from a few inches to several feet, and in width up to 300 ft. These channels are continuous and are probably ancient stream-beds. They are for the most part covered with an over-burden of a more recent gravel, varying from 30 to 50 ft. thick, and the fact that this over-burden contains values as high as $1.50 per cubic yard, and yet was not worked by the Indians, shows that their idea of what constituted mas high.

Jan 1, 1911

By Nicholas J. Grant, Italo S. Servi

SPECIAL polishing and etching techniques were developed during an investigation of the high temperature mechanical properties of high purity aluminum (99.995 pct Al).* Electrolytic polishing was done successfully in the following electrolyte: 5 ml perchloric acid (72 pct), and 95 ml glacial acetic acid. No special precautions need be taken during the preparation of the electrolyte since no appreciable heat of mixing is evolved. Although the electrolyte is not an explosive, it is recommended that Jacquet's safety rules' be followed during the polishing operation. A voltage of 25 to 60 v gives a good polish in about 2 min at room temperature after preparation on 3/0 metallographic paper. Most of the grain boundaries are visible under the microscope after polishing. Since the current is controlled essentially by the resistance of the bath, it is necessary to keep the anode-to-cathode distance as constant as possible. Accordingly, polishing of irregularly shaped pieces will be difficult. A cooling bath and a stirring system are advisable in order to keep the temperature of the bath uniform and constant. Coarse-grained samples can be macroetched in a few seconds by lowering the voltage below 10 v. This is done after electrolytic polishing, without removing the sample from the bath, Fig. 1. The specimen can be repolished in less than 1 min by raising the voltage above 25 v. The "galvanic etching" technique, which has been described elsewhere,' was found to be helpful not only for macroetching, but also for microetching coarse-grained specimens. In fact, the different orientations of adjacent grains provide good contrast at the grain boundaries, when the sample is observed under polarized light. If the specimen is only partially etched, Fig. 2a, the grain boundaries can be located without completely destroying the appearance of the surface of the specimen. The unetched surface appears black under polarized light. Excellent color contrast is obtained by using a "sensitive tint" plate in the optical system of the microscope. In this case, the unetched surface has a magenta color, while the etched part of the sample assumes different colors varying from green to brown, according to the orientation of the grains. Etch pits were produced on high purity aluminum by using the technique suggested by Lacombe and Beaujard." Good results also were obtained by substituting 70 pct nitric acid for the fuming nitric acid recommended. This gave an etching reagent of the following composition: 70 ml nitric acid (70 pct), 50 ml hydrochloric acid (37.5 pct), and 3 ml hydrofluoric acid (48 pct). An example of the results is shown in Fig- 2b. The outline of the etch pits is revealed sharply if the specimen is observed under polarized light, as shown in Fig. 2c. These metallographic techniques are not suitable for the examination of commercially pure (2s) aluminum. References 'P. A. Jacquet: Metal Finishing (Nov. 1949) 47, p. 62. 21. S. Servi: Metal Progress (1950) 58, p. 732. 3 P. Lacombe and L. Beaujard: Journal Inst. of Metals (1947) 74, p. 1._________________________

Jan 1, 1952

By R. I. Jaffee, J. G. Dunleavy, H. R. Ogden, Webster Hodge

INTRODUCTION EARLY in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fick1 and Ruer and Goerens2 definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line off immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 1570°C in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Ford5 have shown that, when hot-rolled copper iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have 150,000 psi tensile strength, and about 41 pct IACS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult, In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation 0f this type of alloy. As a result 0f this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1948

By R. C. Temps, G. E. Aiken

Compania de Acero del Pacifico, S.A., the sole Chilean steel producer, is adding to the expanding Chilean economy with development of the El Algarrobo mine. Expected to go on stream early in 1962, Algarrobo is a conventional open pit mine that will include facilities for ore extraction, crushing and screening, rail transport to the harbor at Huasco, modern ship-loading equipment and maintenance shops. CAP anticipates producing 1.38 mil- lion tons annually of high-grade ore for national and world market consumption. Chilean and North American management and engineering teams combined more than a decade ago in the financing and building of CAP'S Huachipato integrated steel plant. A similar performance is being achieved in northern Chile near the town of Vallenar with the opening of a 50-year supply of iron ore from the Algarrobo deposit. This successful intra-American undertaking deserves special mention in these times when some U.S. foreign assistance programs must be defended, particularly with respect to Latin America. North American financial participation in Algarrobo, through the Export-Import Bank of Washington, represents the greatest portion of the $24 million being invested.

Jan 3, 1962

Discussion of the paper of E. W. Parker, presented at the New York meeting, February, 1913, and printed in Bulletin No. 75, March, 1913, pp. 443 to 451. A MEMBER :-I would like to call attention to the fact that the speaker has failed to indicate where is the center of gravity of the membership of the Institute, while he is dealing with this map. MR. PARKER :-I think you will find that a little further east. CHAIRMAN JAMES F. KEMP :-In connection with Mr. Parker's paper, I would like to inject a little matter of history into our program here, as regards the founding of the Institute. The credit for the founding of the Institute really applies to miners who were engaged in the anthracite coal region. The three men who signed the circular for the call for the meeting which brought the engineers to Wilkes-Barre in May, 1871, were Eckley B. Coxe, Richard P. Rothwell, and Martin Coryell.

Jan 5, 1913