Search Documents

COMPARED with the equipment used in most industrial processes, the open-hearth furnace has a relatively short life. The most important quality of an open-hearth refractory, therefore, is its rate of failure. This discussion of the physics and chemistry of the individual refractory materials will keep uppermost the question "Why, how, and where does it fail?" CAUSES OF FAILURE The principal causes of failure of open-hearth refractories are, in their order of importance : 1. Reaction with iron oxides. 2. Reaction with slag. 3. Flow and failure under load. 4. Melting. 5. Spalling. 6. Mechanical breakage. Reaction with Iron Oxides and Slag. Reaction with iron oxides and slag is by far the most important cause of failure. Liquid iron oxide comes near to being the "universal solvent" sought for by the alchemists. Among the materials commonly used in the open-hearth furnace, magnesia has the greatest resistance to this liquid and fireclay the least. The relations of iron and oxygen at high temperatures are illustrated in Fig 14-18. The liquid iron oxide that forms wherever iron is in contact with air or combustion gases cannot be given a definite formula. The percentage of oxygen at steelmaking temperatures may range from 21 to 28 (iron 79 to 72), depending upon the temperature and the oxygen pressure and also upon whether or not the liquid is in equilibrium with metallic iron. Oxide mixtures exist not only in the solid and liquid phases but also in the vapor phase, for metallic iron and its oxides have

Jan 1, 1964

By H. Hubert

THE first attempts at direct utilization of blast-furnace gas in engines were made in 1895. For a considerable time the gas had been burnt in Cowper stoves for heating the blast for the furnace, and under the boilers which supplied steam to the blowing-engines, and others serving the furnaces. It was natural, therefore, that the idea of directly employing it in gas-engines should have occurred simultaneously to several engineers, notably to Lürmann and to Lencauchez, who had pointed out the blast-furnace as a powerful -gas-producer. Nevertheless, nowhere had any attempt been made to apply it to this purpose up to the end of 1894, when Thwaite proposed it to Mr. James Riley, of the Glasgow Iron & Steel Company. About the same time investigations were being made in Belgium and in Germany, independently of Thwaite's experiments, which were not generally known on the Continent. The industrial world, which up to that time had hardly favored the idea, had thus been gradually prepared to receive it. The gas-engine, long restricted to small sizes and dependent upon the use of an expensive fuel obtainable only in large centers, now began to make headway. At the Paris Exhibition of 1889 two engines of 100 h.p. were shown and excited much interest among engineers. One had four cylinders, and was made at the celebrated works of the Deutz Company, and the other was a single-cylinder engine, exhibited by two French designers, Messrs. Delamare-Deboutteville and Malandin. In the meanwhile the design of gas-producers had made important progress, completely freeing the new engine from its

Nov 1, 1906

By David E. Hyatt, Christopher H. Cox, Franklin T. Davis

INTRODUCTION The composition of water used in the flotation process has always been of primary interest to the flotation metallurgist. It is by alteration of the chemistry of the water introduced to the process that flotation separation is effected. In only a few cases has it been necessary to treat available water prior to use in the process. In the past, flotation tailings were treated for the removal of solids via the tailings dam and water decanted from the dam was either recirculated to the process or discharged to the surface water system. The choice of recirculation or discharge was based upon water availability, effect of recycle water on the process, and economic considerations. The Federal Water Pollution Control Act Amendments of 1972 have charged the United States Environmental Protection Agency with establishing effluent limitations from point sources of discharge into the navigable water of the United States. A detailed study, sponsored by EPA, of the water of ore processing plants took place in 1974 and 1975 and guidelines for these plants will presumably have been published by the time this paper has been presented(1). The action of many of the individual states preceded the EPA in this attempt to regulate the quality of the water discharged from industrial point sources. Even with recycle of tailings water, some water is discharged from tailings dams into the substrata and at least one state is currently preparing guidelines for the quality of water discharged into the substrata.

Jan 1, 1976

By Sharon Brady, Catherine O’Donoghue, John V. Beall, Paul C. Merritt

Between 1950 and 1965, more than 80% of all phosphate rock produced in the world each year was used as fertilizer, either directly applied to the soil or processed into mixed chemical fertilizers. Of the potassium salts produced, 95% followed suit. A variety of uses in industrial chemicals and consumer products absorbed the remaining percentage of each. Future trends in these two commodities will be dominated by what happens to the fertilizer market. Farming is much the same as mining the soil. Plants remove the minerals little by little. Phosphate and potash comprise two of the three primary nutrients removed in this way, the third being nitrogen. Phosphate stimulates early root formation and growth, whereas potash is a salt necessary to root strength.

Jan 10, 1966

R. W. Raymond, New York, N. Y,:—Since the presentation of my note on this subject at the New York Meeting, Professor Louis has pointed out an error in my statement of his conception of " pitch "—namely, he understands the pitch, in the restricted sense which he proposes, to be the angle of inclination of the axis of an ore-body, measured on the vertical plane drawn through the body; whereas, I represented him as proposing to define " pitch " as the angle of inclination of an oblique body, measured on the plane of the dip, in the direction of the strike. The difference will appear upon consideration of the accompanying isometric projection, Fig. 1, in which ABCD represents the plane of the inclosing ore-deposit (vein or bed), and AC the axis of the oblique ore-shoot. ABE is the angle of the dip, as universally understood; and ACE

Jan 1, 1909

Discussion of the paper of E. C. HARDER, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2573 to 2586. I. C. WHITE, Morgantown, W. Va.-I have seen some of the great iron-ore deposits described in this paper. -One of these in the State of Minas Geraes appears to be an immense mountain of iron ore about 2,000 ft. in height. All over its surface from bottom to top may be seen large masses of rich iron ore, varying in weight from a few pounds to several tons, and from all that one can judge without exploitation, the quantity of available ore is certainly very large in this particular mountain. Whether it will prove a mere surface deposit or shell, like the famous Iron Mountain of Missouri, is for future exploration to determine. The question of transportation is the main factor in determining the availability for exportation of these Brazilian iron ores. There is no coal in Brazil that can be manufactured into coke without expensive previous treatment, since the best of the raw coal in the States of Rio Grande do Sul, Santa Catharina, and Parana, contains about 35 per cent. of ash, of which about 6 per cent. is sulphur, and coal of this composition cannot be utilized in iron smelting without purification. When I was chief of the Brazilian Coal Commission in 1904 to 1906, I had a cargo of this coal shipped to Balk, Germany, and treated in the great coal-testing plant of the Humboldt Engineering Works, located just across the Rhine from Cologne. It was found that by crushing and washing the Brazilian coal, it yielded 33 per cent. of briquetting coal, containing only 10 to 12 per cent. of ash (of which 1 per cent. was sulphur), and 42 per cent. of slack coal, with 25 per cent. of ash and low in sulphur, so that about 33 per cent. of the Brazilian coal could be converted into coke of fair quality, as shown by the following average of three analyses, using air-dried coal, of briquets made from the Barro Branco coal bed, State of Santa Catharina: Moisture 1.56 Volatile matter 31.66 Fixed carbon 56.73 Ash : 10.05 Total 100.00 Sulphur 1.34 Phosphorus 0.003 B.t.u 13,395

Jan 4, 1915

By A. A. Smith, J. S. Smart

THE elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses, When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range 0 to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorily determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing and oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B. and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold, The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300° and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type, All samples were quenched from the annealing temperature in 10 per cent H2SO4 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.1 EFFECT OF SILVER Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

By Thomas A. Edison

We have not yet begun. to realize the possibilities of automatic machinery, in part because we have not developed the designing brains, and in part because we have not sufficiently simplified industry to make possible the economical use of such machinery. The principle of the Jacquard loom, has scarcely been utilized except in weaving silk and in the player piano. It is the principle of bringing into action the various parts of a machine in accordance with a pattern traced on a steel card by perforations or as on the paper roll of a player piano. This principle gives us a control which can be applied to any kind of machine. It is a' great reserve principle for the future. But even now, with the machinery that we have at command, anyone can cut the number of employees in two, at the same time doubling his output, by installing semi-automatic or automatic machinery. And no one knows how far this process can go on. Cutting down the number of men is not just putting some poor fellows out of a job. It is increasing the number of good jobs by increasing the production per capita to a point where really satisfactory wages can be paid out of it, and this in turn- increases the amount of work required to be done and creates new jobs. Thus, cheapening in- creases the demand.

Jan 1, 1929

By Frances H. Clark

DEVELOPMENTS in powder metallurgy have been disappointing in 1943. If any new part has gone into large-scale production, knowledge of it has been restricted by considerations of national security. Nor have any outstanding papers appeared to advance the theory of the subject during this period.

Jan 1, 1944

By John D. Sullivan, Edwin J. Rogers, Chester R. Austin

THE problem of making a building unit combining the necessary physical and mechanical properties and good thermal insulation has been foremost in the minds of architects and ceramic and construction engineers for many years. This paper presents the results of studies on thermally expanding shales or clays to produce light-weight cellular products suitable for making building units. An expanded clay block suitable for building purposes should be large enough so that substantial savings may be effected in labor costs in laying the wall. The permeability should be low and it should have sufficiently good "dry-wall" characteristics to permit exposing the exterior surface to the elements, and to permit plastering directly the inside wall surface. The thermal conductivity should be low and the mechanical properties should be adequate. Obviously, a unit possessing satisfactory qualities for constructing an outside wall would be satisfactory for interior walls and for back-up purposes. The results of studies on bloating various shales or clays[t] and the properties of the expanded products are reported. In another paper1 basic factors involved in bloating of clays are discussed. Manufacturers of ceramic products, particularly structural clay, may encounter bloating of the ware during burning, and precautions must be followed to avoid this phenomenon. About 1927 the C. F. Burgess Laboratories, Madison, Wis., while carrying on an investigation for the American Face Brick Research Corporation, conceived the idea of intentionally bloating clay while holding it in a restrained condition, with the hope of producing a unitary cellular mass. Work was carried on until about 1931, when studies were terminated because of business conditions. These studies were continued later by The Western Brick Co., Danville, Ill., which developed a process of "inwardly expansive bloating."2 The major purpose of the latter investigation was to produce back-up tile to compete with concrete blocks made from Haydite or cinder aggregate. Haydite is a light-weight aggregate formed by heating certain clays or shales rapidly in a rotary kiln. While the investigations at the C. F. Burgess Laboratories or at Western Brick Co. were not carried far enough to lead to the commercial production of material for the construction of walls, particularly outside walls, they showed that certain clays could be thermally expanded and that it was possible to produce a material of low permeability with a large percentage of the total voids or cells closed. Commencing in 1939, the Ozark Chemical Co. sponsored a research program at Battelle Memorial Institute for the purpose of determining whether it is technically feasible to make thermally expanded building units, and specifically to get answers to the following questions:

Jan 1, 1942

By A. H. Kline, E. B. Zimmer, Zay Jeffries

It is well known that many properties of a given metal vary with the size of grain or cell. For most industrial purposes, where high ultimate strength and high elastic limit are desired, the manufacturer tries to produce a fine-grained structure. For some purposes, for example in transformer iron, a coarse-grained structure is desirable. The terms fine-grained and coarse-grained are used only in a relative sense. For example, a fine-grained cast copper might have grains 100 times larger than coarse-grained high-speed steel. Similarly, a finegrained steel rail might have grains or cells 100 times larger than coarsegrained wire, which was made of steel from the same heat. In some metals, the change in grain size is more appreciable khan the changes in any of the properties determined by the tensile test. Furthermore, in metals which have been annealed or subjected to high temperatures, grain size may prove to be a better indication of the life of the metal in use than the tensile test. One of the authors was able to supplant the tensile test with grain-size determinations in the control of metal for a specific use, the latter determination being more indicative of the life of the metal part than the tensile test. A grain-size determination with a tensile stest is, of course, more valuable than either singly. At present there is a decided dearth of data on actual grain-size determinations in metals, and consequently a corresponding lack of ability to interpret the determinations after they are made. It would be desirable to have correlation made between grain size and properties of metals, comparing thousands of determinations. In this way, grain-size determinations might be interpreted in much the same manner that tensile tests are now. Several Methods of Measuring Grain Size One of the chief reasons why more grain-size measurements have not been made is the excessive work involved in making a determination.

Jan 1, 1916

By E. A. Steigerwald, G. L. Hanna

The influence of work-hardening exponent on the variation of fracture toughness with material thickness was studied for high-strength steel, aluminum, and titanium alloys. The results indicate that, when materials are compared at similar fracture toughness to yield strength ratios, the material with the lower work-hardening exponent undergoes the transition from flat to slant fracture at a larger thickness than material with a high work-hardening exponent. In the thickness range where complete slant fracture is obtained the reverse is true and a lower work-hardening exponent results in a lower fracture toughness. The influence of work-hardening exponent on fracture toughness is, therefore, dependent on the particular fracture mode. In the transition region a low work-hardening exponent is beneficial for fracture toughness while in the 100 pct slant region it is detrimental. THROUGH the use of fracture mechanics analyses, the influence of geometric variables on the crack propagation resistance of structures can be interpreted with reasonable consistency. However, in order to gain a more complete understanding of the fracture process, the influence of material parameters on crack propagation must be defined and coupled to the macroscopic fracture mechanics approach. The work-hardening exponent, which characterizes specific material behavior, may serve as an effective parameter to allow some degree of coupling to be accomplished. In the extension of a crack in a specimen of suitable dimensions the propagation process occurs in a stable manner when the crack extension force is balanced by the resistance to crack extension, which exists in the material at the crack tip. As the applied stress, and therefore the crack extension force, on the specimen increases, the resistance also increases primarily because the effective plastic zone at the crack tip, which is the main energy absorption process, becomes larger. Since the work-hardening rate of a material influences the stress-strain relationship, it will also influence the energy absorption process in the plastic enclave at the crack tip and hence should have an effect on crack propagation. A number of studies have been made correlating the strain-hardening exponent or the strain to tensile instability with the ability of a material to resist fracture. Gensamer1 concluded that a low-strain-hardening exponent would result in a steep strain gradient at the base of a notch. He reasoned that a large work-hardening coefficient would result in high-energy ab- sorption due to the increased area under the stress-strain curve. Larson and Nunes2 experimentally observed in Charpy tests on steels heat-treated to below 200,000 psi yield strength that the energy to failure in the fibrous mode, i.e., above the brittle-to-ductile transition temperature, was logarithmically related to the strain-hardening exponent. In order to avoid the complicating effects present in studying materials which undergo a brittle-to-ductile transition, Ripling evaluated the notch sensitivity of a variety of fcc metals with varying work-hardening exponents.3 The results indicated that the relative notch sensitivity, as determined from tests on specimens with a sharp notch, decreased with increasing values of strain hardening. Although the energy required for ductile or fibrous fracture increases with increasing work hardening, high-strength steels often exhibit improved crack propagation resistance when heat-treated to obtain low values of strain hardening.4,5 An analysis of whether low strain hardening is beneficial or detrimental to crack propagation resistance must depend on the particular fracture criterion involved. At temperatures where the material is relatively ductile and the development of a critical strain is required for fracture, high strain hardening increases the energy required to produce failure. In the transition region and below, however, a critical stress law appears to be valid6 and a low rate of work hardening may produce superior resistance to semibrittle crack propagation. The experimental program is aimed at studying these possibilities and determining the specific influence of strain hardening on the crack propagation resistance of several high-strength materials. MATERIALS AND PROCEDURE The alloys, chosen as representative of various classes of high-strength materials, are summarized in Table I. The heat treatments evaluated along with the smooth tensile properties are presented in Table 11. Pin-loaded sheet tensile specimens were employed to determine the smooth tensile properties. A strain gage extensometer (measuring range 0.200 in.) was used at a strain rate of 0.02 in. per in. per min. The work-hardening exponents were determined from the stress-strain curves generated in the smooth tensile tests and the assumption that the portion of the stress-strain curve beyond the yield point can be described by the power relationship: where a is the true stress, P is the true plastic strain,

Jan 1, 1969

By Franklin Moeller

THE application of electric power for driving, mine hoists handling heavy loads at high speeds has recently been extended by the installation of what is probably the largest electrically driven hoist in this country at the Granite Mountain shaft of the North Butte Mining Co., Butte, Mont. While the weight of rock which is hoisted by this machine is not the largest now being handled by electric mine hoists, the speed of hoisting is so, and the combination of the high speed with the heavy load has resulted in a machine of considerable interest to all those actively engaged in mining. Aside from mere consideration of size, this installation deserves attention because of the careful attention given, not only to the question of economy of operation, but to the details of construction and installation of the entire equipment. The conditions to be met in this installation were as follows: Weight of rock to be raised per trip, 7 gross tons 15,680 1b. Weight of skip 8,0001b. Weight of cage 1,8001b. Maximum depth of hoisting 4,000 ft. Diameter of rope 153 in. Total weight suspended on one rope from drum 42,000 1b. Normal hoisting speed 2,700 ft. per minute. Maximum hoisting speed : 3,000 ft. per minute. Desired capacity-200 tons per hour from 4,000 ft: depth. The ore is mined in several levels and hoisting is carried on from the 800-ft. level down to the 2,700-ft., which is at present the maximum depth from which the ore is raised regularly. Development is proceeding and a depth of 2,900 ft. has already been reached. The rock is handled underground in cars holding ¾ ton, and about 10 cars are the usual load for a skip. All of the ore is clumped into underground bins, which are of different capacities varying up to 250 tons. From the bins the ore is fed into the skips without passing into measuring pockets. At the surface the

Jan 2, 1916

By C. D. Gilpin, Franklin Moeller

The application of electric power for driving mine hoists handling heavy loads at high speeds has recently been extended by the installation of what is probably the largest electrically driven hoist in this country at the Granite Mountain shaft of the North Butte Mining Co., Butte, Mont. While the weight of rock which is hoisted by this machine is not the largest now being handled by electric mine hoists, the speed of hoisting is so, and the combination of the high speed with the heavy load has resulted in a machine of considerable interest to all those actively engaged in mining. Aside from mere considcration of size, this installation deserves attention because of the careful attention given, not only to the question of economy of operation, but to the details of construction and installation of the entire equipment. The conditions to be met in this installation were as follows: Weight of rock to be raised per trip, 7 gross tons........... 15,680 1b. Weight of skip.......................................... 8,000 1b. Weight of cage.......................................... 1,800 1b. Maximum depth of hoisting.............................. 4,000 ft. Diameter of rope.......................................... 15/8 Total weight suspended on one rope from drum............. 42,000 1b. Normal hoisting speed.................................... 2,700 ft. per minute. Maximum hoisting speed.................................. 3,000 ft. per minute. Desired capacity-200 tons per hour from 4,000 ft. depth. The ore is mined in several levels and hoisting is carried on from the 800-ft. level down to the 2,700-ft., which is at present the maximum depth from which the ore is raised regularly. Development is proceeding and a depth of 2,900 ft. has already been reached. The rock is handled underground in cars holding % ton, and about 10 cars are the usual load for a skip. All of the ore is dumped into underground bins, which are of diffcrent capacities varying up to 250 tons. From the bins the ore is fed into the skips without passing into measuring pockets. At the surface the

Jan 1, 1916

By W. H. Emmons

This paper is the third of a series treating of the relations of ores of the metals to igneous rocks. The first' outlined the general problem; the second2 proposed a classification of lode ores, and showed how the distribution of the deposits is in a certain measure controlled by the contour of the roof of the parent batholith. A number of mining districts were discussed, the examples being selected chiefly from group 2 of the classification. The proposed classification of lode deposits, briefly stated, is as follows: 1. Cryptobatholithic: near hidden batholiths which have not yet been exhumed by erosion. 2. Acrobatholithic: in and near cupolas or domes of batholiths—the high points of larger underlying masses. 3. Epibatholithic: on batholiths, near their rims, but below eroded cupolas, or below the highest points of the roofs. 4. Embatholithic: among closely-spaced outcrops which probably are parts of a single bathohth. The outcrops of invaded rocks predominate. 5. Endobatholithic. in and near roof pendants of large batholiths. The invading rocks predominate. 6. Hypobatholithic: in deeply-eroded batholiths, where even roof pendants have been eroded. Deposits of certain metals on the roofs of the batholiths are much more numerous in some positions than deposits of other metals, and the horizontal zonal arrangements of lodes of different metals are shown characteristically only in certain groups. In a large measure, also, the character of the fracturing and metallization is determined by the position on the roof of the batholith. The disseminated copper ores in porphyry constitute a clearly-defined type. All the deposits of these ores, as far as known, are in group 2. They appear to have been formed only in and around small upward projections of the parent granitic masses, and not low on the walls of the

Jan 1, 1927

By Wm. E. Milligan

LEAD stocks at the beginning of 1943 were comfortable when compared with those of other base metals such as copper, zinc and tin. This situation was early recognized by W.P.B. and other Governmental agencies and every effort was made to encourage the substitution of lead for these latter metals in all essential uses. Despite this apparently healthy condition, lead was not denied participation in the various measures inaugurated by the Government to relieve metal shortages. Thus in the Mexican trade agreement, effective Jan. 20, the tariff on two important classes of lead importss was halved. Similarly, in the setting up of B quota premiums, a B base was allotted to lead, with all pro¬duction above this figure receiving an additional payment of 2.75c. per lb., or a total payment of 11.75c. per lb. At about the same time it was announced that all quota transactions would be based upon the lead content as shown by the smelter settlement sheets. This basis was 86 percent of the lead content for all ores shipped to custom milling plants and 95 per cent for ores and concentrates shipped to custom smelting plants. The importance of this action can be appreciated when in the Coeur d'Alene it was estimated as equivalent to a 5 per cent increase compared to the previous base.

Jan 1, 1944

By John Porter

THE requirements of the standard specifications under which Portland cement is sold have materially increased within the past 10 years, but practically all companies are now furnishing cement better than these requirements; in some cases exceeding them by nearly 100 per cent. From a sales standpoint, it is desirable to have a product that is uniform to a high degree and free from occasional quality troubles. A failure in quality, even if it affects only a few hundred barrels out of a yearly output of a million or more, is apt to be talked about in the trade and to affect the salability of the entire output. For these reasons, there has recently been great activity along the lines of quality control and improvement; and some of the most interesting problems of the industry are in this field. From the manufacturing standpoint, the quality of cement is chiefly a matter of uniform and proper chemical composition of the raw mix fed to the kilns plus proper burning in the kilns; the fineness to which the cement is ground, the proportions of gypsum, the method of seasoning, and the like are contributory factors. Uniform chemical composition of the raw mix has been one of the most difficult problems to solve. Most plants will use from 1000 to 3000 tons of rock per day and in but few cases is this material as it lies in the quarry even approximately uniform in composition. The problem, then, is to quarry and mix this raw material in such a manner that every handful passing through the kilns will have practically the same analysis as every other handful. To accomplish this purpose there are two methods of preparation: the wet process and the dry.

Jan 1, 1925

By Hans Allenius, R. T. Hukki

This paper describes in quantitative terms the effect of sharpness of classification on the performance of the closed grinding circuit. The analysis is based on a large number of laboratory experiments designed to simulate the two most common industrial closed grinding systems. The experimental results show quantitatively the degree of improvement achievable by more efficient classification. In an earlier paper1 the senior author has presented a trend showing qualitative analysis of mill and classifier performance in tile closed grinding circuit. According to this analysis, the master key to a major improvement appeared to be effective removal of finished fine material from the classifier sands, or in other words, improved sharpness of classification, leading simultaneously to a substantial reduction of the circulating load. One purpose of this paper is to present the results of a quantitative investigation of the closed grinding circuit. Another is to set forth the essential pertinent variables revealed by the quantitative experiments carried out by the junior author. In the two most common systems of closed-circuit grinding, (1) feed to the circuit is introduced into the grinding unit, normally the ball mill, operating in closed circuit with the classifier; or (2) feed to the grinding circuit is introduced into the primary grinding unit, normally the rod mill, discharging into the classifier in closed circuit with the secondary grinding unit, normally the ball mill. In the following discussion, these two systems are analyzed separately in the indicated order. BALL MILL - CLASSIFIER CIRCUIT The Test Apparatus and Procedure: The test appara- tus included: (1) a F 195 mm x 220 mm laboratory ball mill rotated at a speed 77% of the theoretical critical speed, and a 7-kg batch of F 20 mm-F 50 mm steel balls; (2) a conventional 65-mesh test sieve and a Ro-Tap sieve shaker serving as a classifier; and (3) a Permaran instrument manufactured by Outo-kumpu Co. for surface area determinations by the permeability method. As no continuous closed-circuit experiments could be brought about on a laboratory scale, the process was broken down into alternating grinding and sizing steps in such a way that the new feed plus the returning sands always formed a batch of 1000 gm. For each selected grinding period and for each selected sharpness of classification the basic steps were repeated six times. Steady-state conditions were then reached. Crystalline vein quartz was used as a test material. Feed to the process consisted of -10-mesh fraction of this quartz crushed in rolls. This fraction included 15% of-65-mesh material. Experimental Results: The general flowsheet is shown in Fig. 1. Table I gives the essential data obtained representing steady-state conditions under the indicated set of variables. The table is based on 110 grinding experiments, 440 screen analyses and an equal number of specific surface area determinations. Fig. 2 shows the relationship between the cumulative net energy consumption and the cumulative number of mill rotations as evaluated by separate experiments. Note that this relationship is not linear but is instead represented by a slight curve. The data given in Table I are presented in graphical form as follows: Fig. 3 shows the produced -65-mesh material in grams per minute vs. time of grinding in minutes; the sharpnesses of classification at 65 mesh were 100%, 75% and 50%. It is clearly indicated that the highest-capacity figures call for relatively short grinding times and for the sharpest possible classification. Fig. 4 presents the specific surface area on the final -65-mesh product in square centimeters per gm vs. time of grinding in minutes. In conventional mineral dressing processes, a final product characterized

Jan 1, 1969

By S. A. Falconer

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included. TODAY, as never before, the coal producers of this country are faced with the necessity for obtaining maximum yield of marketable coal of all sizes down to and including the finest. Particular interest is being displayed in a more effective means of recovering the finer sizes which in the past so often have been discarded to waste or treated by inadequate equipment. The reasons for this interest are easily understood. Rising mining costs have resulted in the increased use of mechanized equipment underground for full seam mining. This, in turn, means more refuse in the run-of-mine and also more fines in the feed going to the cleaning plant. Stringent antistream pollution laws now make it necessary at least to impound the fines, and usually it is a paying proposition to recover the coal from these fines before sending them to the storage area. Finally, the market and price of the finer sizes has increased, but at the same time specifications have tightened and the demand is for higher grade products. During the past four years a great deal of publicity has been given to this new process and apparatus for treating fine sizes of ores as well as coal. Excellent discussions of the apparatus itself and the theoretical aspects of the basic operating principles involved in its operation have been presented by M. G. Driessen,1-3 M. R. Geer and H. F. Yancey,4,5 J. W. Hyer6 and more recently by D. A. Dahlstrom8 as well as others.7,9-11 In view of this, it has been decided to include in the present paper only a brief description of the cyclone separator and its operating principles. This paper deals primarily with some of the more practical commercial aspects of the process and equipment required for its operation; the variables in the operation of the cyclone, their effect and means for control; and the results obtained with a 6-in. semicommercial size separator on a variety of fine coals, bituminous and anthracite, using finely ground magnetite for the separating medium solids. A description is included of the commercial-size cyclone separator pilot plant installed by the Dutch State Mines at its Emma mine in Holland, where finely ground slate is utilized as medium solids. Field of Application: The Dutch State Mines cyclone separator operates most efficiently on ores and coal in the size range of % in. to about 48 mesh. On some types of feed, effective separation can be made on sizes as small as 100 mesh, but up to the present, this may be considered exceptional. Depending upon the type of medium used, the specific gravities of separation can be varied within wide limits, up to as high as 2.70, if magnetite is used as medium. Early Development: The development of the Dutch State Mines cyclone as a separator, or cleaner, was the outgrowth of early experimental work by Dries-sen' and others in Holland, just prior to World War 11, in the course of which was discovered the effectiveness of the cyclone in reclaiming and thickening the dense medium used in the "Loess" process of

Jan 1, 1951

By S. A. Falconer

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included. TODAY, as never before, the coal producers of this country are faced with the necessity for obtaining maximum yield of marketable coal of all sizes down to and including the finest. Particular interest is being displayed in a more effective means of recovering the finer sizes which in the past so often have been discarded to waste or treated by inadequate equipment. The reasons for this interest are easily understood. Rising mining costs have resulted in the increased use of mechanized equipment underground for full seam mining. This, in turn, means more refuse in the run-of-mine and also more fines in the feed going to the cleaning plant. Stringent antistream pollution laws now make it necessary at least to impound the fines, and usually it is a paying proposition to recover the coal from these fines before sending them to the storage area. Finally, the market and price of the finer sizes has increased, but at the same time specifications have tightened and the demand is for higher grade products. During the past four years a great deal of publicity has been given to this new process and apparatus for treating fine sizes of ores as well as coal. Excellent discussions of the apparatus itself and the theoretical aspects of the basic operating principles involved in its operation have been presented by M. G. Driessen,1-3 M. R. Geer and H. F. Yancey,4,5 J. W. Hyer6 and more recently by D. A. Dahlstrom8 as well as others.7,9-11 In view of this, it has been decided to include in the present paper only a brief description of the cyclone separator and its operating principles. This paper deals primarily with some of the more practical commercial aspects of the process and equipment required for its operation; the variables in the operation of the cyclone, their effect and means for control; and the results obtained with a 6-in. semicommercial size separator on a variety of fine coals, bituminous and anthracite, using finely ground magnetite for the separating medium solids. A description is included of the commercial-size cyclone separator pilot plant installed by the Dutch State Mines at its Emma mine in Holland, where finely ground slate is utilized as medium solids. Field of Application: The Dutch State Mines cyclone separator operates most efficiently on ores and coal in the size range of % in. to about 48 mesh. On some types of feed, effective separation can be made on sizes as small as 100 mesh, but up to the present, this may be considered exceptional. Depending upon the type of medium used, the specific gravities of separation can be varied within wide limits, up to as high as 2.70, if magnetite is used as medium. Early Development: The development of the Dutch State Mines cyclone as a separator, or cleaner, was the outgrowth of early experimental work by Dries-sen' and others in Holland, just prior to World War 11, in the course of which was discovered the effectiveness of the cyclone in reclaiming and thickening the dense medium used in the "Loess" process of

Jan 1, 1951