Search Documents

By Samuel Daniels

The Al-Cu-Ni-Mg alloy is much benefited by heat treatment and, in such condition, is preferable to the Al-Cu-Fe-Mg alloy either as cast or as heat-treated, when both are reheated to temperatures of from 400" to 600" F. and compared, cold, with respect to strength and to hardness. The main differences between the alloys do not arise until the reheating temperature exceeds 400" F., above which they gradually soften. This softening is characterized metallographically by the appearance of intragranular precipitate. The Al-Cu-Ni-Mg alloy is weakest and least hard after being reheated at 600" F., the Al-Cu-Fe-Mg alloy at about 700" F. The former starts to reharden at 700" F., the latter at 800' F. There is a tendency for both alloys to lose strength and hardness with prolongation of time at the reheating temperatures of 500" and of 700" F. The Al-Cu-Ni-Mg alloy is considerably stronger and harder than the Al-Cu-Fe-Mg alloy when both are heat-treated and reheated for long periods of time at 500" and 700" F. Although the latter can be made harder initially than the Al-Cu-Ni-Mg alloy by suitable quenching and aging, heat treatment, in general, favors the retention of this initial (strength and) hardness after reheating to a much greater degree in the Al-Cu-Ni-Mg alloy. The percentage of elongation of the two materials in any condition is very small. Certain aluminum alloys have been used for pistons and other parts operating at temperatures up to 650" F. because of their lightness, high thermal conductivity and specific heat, fair strength and hardness at elevated temperatures, excellent machineability, and moderate resistance to corrosion. In the piston, the inertia forces and the bearing loading, and with this the vibration, are decreased. The piston head functions at a lower temperature (about 200" F. below one of cast iron), so that, because of the lessened tendency toward carbonization and detonation, higher compression ratios may be used. On the other hand, the aluminum alloys do not have the wearing and bearing qualities of cast iron; also they have a large coefficient of expansion, allowance for which must be made in the design. The range in analyses of aluminum alloys, used for pistons in domestic and in foreign internal-combustion engines is shown in Table 1. There seem to be three general types of composition; one containing about 10

Jan 1, 1926

By Louis A. Carapella, William E. Shaw

MAGNESIUM and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitional point has been set at 225°C by Schmid1 for single crystals, and at 250°°C by Morell and Hanawalt2 for extruded magnesium metal. In a recent X-ray investigation on polycrystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional temperature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheett over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig r. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Hargreaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Hargreaves constant S, was obtained by the integrated or intermittent loading procedure. The authors5 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformational loads. These findings have been applied

Jan 1, 1947

By W. E. Mitchell

ELECTROLYTIC, production of cadmium at the Great Falls plant started in the first part of the year 1925. Prior to that time, an experi¬mental unit had been in operation for a few months during the year . 1922. At present the plant is the largest producer of cadmium, not only in the United States but in the world. Electrolytic cadmium is characterized by its very low content of impurities. The main impurities, which are lead, copper, zinc, and iron, do not aggregate more than 0.05 per cent., leaving a cadmium content better than 99.95 per cent. The consumption of cadmium has increased rapidly since the war, with the growing use in the plating industry. Cadmium plating has come into prominence because of its connection with the automobile and radio industries. As a protective coating, a deposit of, cadmium is superior to zinc. Cadmium is also used extensively in alloys. Important among these is the alloy with copper used in telephone and trolley wire. In proportion of 0.5 to 1.2 per cent., cadmium adds materially to the strength and wearing qualities. Practically all commercial zinc concentrates contain a small amount of cadmium. In the electrolytic zinc process, the cadmium that is dissolved in the regular leaching operation is removed from solution with metallic zinc, generally added in the form of zinc dust. This precipitate also contains the copper taken into solution and the excess of zinc dust, which is required in order to insure a complete removal of all impurities. The precipitate is treated by a separate process to recover the copper, cadmium and excess zinc. In order to make the metals more soluble and to render insoluble such impurities as iron, arsenic and antimony, the precipitate is roasted. The roasting is carried out in gas-fired McDougall furnaces, with a roasting temperature of about 700° C.

Jan 1, 1930

By James R. Holden, Frederick E. Wang

Through both single-crystal and powder X-ray diffraction methods, ten A6B23-type compounds have been confirmed to exist between lanthanides (A) (plus scandium and yttrium) and manganese (B); A = Y, Nd, Sm, Gd, Tb, Dy, Ho, Er, Tm, and Lu. The formation of a compound of this type is shown to he extremely atomic size-sensitive; hence it can be classified as a "size-factorH compound. The "enveloping effect", a geometrical consideration observed in its crystal structure, is proposed as the reason for the A6B23-type compound being size-sensitive. The approximate ideal geometrical ratio of the radii R/r is 1.31 while experimentally A6B23-type compounds have a radius ratio lying within the range 1.2 to 1.4. FLORIO t al.' characterized the structure of Th6MnZ3 as fcc, space group Fm3m, with 116 atoms in the unit cell. Since then, a number of isotypic binary compounds, and recently Gd n,,' have been confirmed to exist. The fact that strontium and barium form A6Bz3-type compounds with magnesium strongly suggested the possible existence of Ba6Liz3. However, investigation3 showed the compound Ba6LiZ3 to be absent. Since both strontium and barium are group 11-a elements and are therefore "open metals",6 the nonexistence of Ba6LiZ3 can hardly be explained satisfactorily by valence-electron considerations. On the other hand, the consistent atomic-radius ratio, (R/r),* observed for the known A6Bz3-type compounds,3 strongly suggests that the formation of compounds of this type is atomic size-sensitive. Therefore, one is tempted to explain the nonexistence of Ba6LiZ3 entirely on the basis of the atomic-size difference between strontium and barium. However, this approach is not entirely without objection. Atoms are not rigid spheres and are known to vary in size within certain limits.7 Since the atomic-radius difference between strontium and barium (0.07 to 0.09A) is within these limits, it is reasonable to assume that the size difference would have a negligible effect on the formation of Ba6LiZ3. This view is further supported by the fact that the radius ratio, R/r, in other known "size-factor" compounds is observed to range widely—for example, from 1.08 to 1.45 for ABz-type compounds (C15, MgCuz type)' and from 1.37 to 1.58 for AB5-type compounds (D2d, CaZn5 type).g The present investigation was undertaken in order to find a more satisfactory explanation for the non-existence of Ba6LiZ3 and, consequently, a better understanding of the nature of the A6Bz3-type compound. The primary objectives are to confirm the previous conclusion3 that the A6B23-type compound is indeed a "size-factor" compound and subsequently to determine the atomic-radius ratio range in which the A6Bz3-type compound can exist. In order to achieve these objectives, stoichiometric A6Bz3 alloys, where manganese (B) was alloyed with various lanthanide elements (A), were selected for investigation. The atomic-radius ratios of lanthanide elements with manganese range from 1.26 for Lu/~n to 1.46 for Eu/Mn. This radius ratio range includes and exceeds the range of all previously reported A6Bz3-type compounds—1.32 for Th/Mn' through 1.38 for Sr/Li. Furthermore, the atomic-size difference between successive elements of the lanthanide series in order of atomic number) is of the order of 0.01A (europium and ytterbium are exceptions). The series of lanthanon-manganese alloy systems is ideally suited to a precise determination of the limits of allowable atomic-radius ratio for A6Bz3-type compound formation. EXPERIMENTAL PROCEDURE The lanthanide metals, in ingot form, supplied by Michigan Chemical Corp. (St. Louis, Mich.) and Nuclear Corp. of America (Burbank, Calif.), were guaranteed by the suppliers to be at least 99.9 wt pct pure (traces of silicon, calcium, and other minor constituents present on occasion, not to be more than 0.05 wt pct) as shown by spectrographic analysis. Manganese metal, in polycrystalline form, was redistilled from the commercial, chemically pure grade and was analyzed to be at least 99.95 wt pct pure. In all cases, the atom ratio between the two elements in each charge was A (rare-earth meta1):B (manganese) = 6:23 and a constant weight, 3 g, of

Jan 1, 1965

By Leon O. Hart

The nickel-chromium alloys of importance are those containing iron and those free from iron. The most important alloys containing iron, with regard to high tonnage, are the nickel-chromium steels. Straight nickel steel was introduced about the year 1889, but it was not until 1895, when it was found that the addition of chromium greatly increased the strength and resistance to shock, that nickel-chromium steels came into use. The three types of nickel-chromium steels developed at this time were: Type 1, containing 3.,50 per cent. nickel and 1.50 per cent. chromium; type 2, containing 2.00 per cent. nickel and 1.00 per cent. chromium; and type 3, containing 1.50 per cent. nickel and 0.50 per cent. chromium.

Jan 1, 1921

By Richard J. Gowen

THE FUTURE The environment in which we live appears to change so slowly that most of us are unaware that any change has occurred at all. As the years pass, we notice increasing smog in our cities, new variations in weather, the shifting landscape with changing populations, and subtle but ever present alterations in the quality of life. In considering the future of our environment, we find we must grapple with questions concerning the very future of life as we know it today. Questions of resources, technology, society, governance, and purpose. Let us focus on the future of our environment and, in particular, raise the question of who is responsible for the environment. We know that action, or lack of action, will clearly influence our future environment. It is fashionable to catalog the many short-sightedness of our forefathers in developing the technologies which support the style of living to which we have become accustomed. However, I shall struggle to resist the temptation to list the well known ills of our present environment. Rather, let us concentrate on the future in our consideration of the priority of the multitude of options proposed to relieve our current energy crisis. We have recently witnessed the dramatic effects of air pollution produced by Mount St. Helen's eruptions. In the state of South Dakota, we watched our blue skies turn hazy and felt our eyes sting with the presence of volcanic ash. We were appalled at the dramatic effects on the landscape, crops, transportation, and all aspects of life in communities immediately downwind of the volcanic eruption. But in a few weeks, life had returned to near normal on the earth's surface leaving the volcanic ash in the atmosphere to ultimately

Jan 1, 1983

By DR. RICHARD RATHBUN

ON behalf of the Regents and the Secretary of the Smithsonian Institution, it gives me great pleasure to welcome you to the National Museum; but it is to your own museum, since it belongs to you in common with all the people of the country. Still young in a life which has been beset with many difficulties, it has gathered strength and attained a growth quite unprecedented. In fact, it is this very growth which has been the chief cause of trouble, always leading far and away beyond the capacity for storage ; and to-day there is nearly as much material contained in outside buildings as is displayed in this one. You will, accordingly, find the collections crowded, the cases so close together that their contents are often difficult to view, and the arrangement generally lacking symmetry. You may, therefore, be inclined to regard us as poor custodians of the collections of a great nation, but I beg you to withhold your judgment for a while. From the beginning there has been abundant zeal and activity and a proper direction of affairs, but space and money have been lacking. There is now a prospect of better times. All about you here is a beautiful park, but without. a covering it is not adapted to museum purposes. Upon it, however, a new large building is going up, so extensive in its dimensions that technology can soon be given a fitting home, thus realizing one of the earliest aspirations of the Regents. Some sixty-five years ago the extensive returns of specimens from the famous Wilkes Exploring Expedition around the world began to reach Washington, where they were deposited in the Patent Office Building, and formed practically the first of the National Collections. Six years later the Smithsonian Institution, based upon the bequest of James Smithson, was

Jul 1, 1905

By AIME AIME

THE section delegates assembled Monday morning with the incoming president, W. H. Bassett, in the chair and F. W. Bradley as vice-chairman. The secretary called the roll and urged the delegates to become familiar with the activities of the Institute. He explained the allotment of funds to local sections and the uses to which these funds may be put. He also announced plans for travel by Mr. Bassett and asked the delegates to confer with him as to meetings en route. An invitation was extended for all section delegates to attend the Directors' dinner Wednesday evening. He suggested that local sections hold a meeting once a year under the auspices of each division of the Institute. He further explained the system of choice of publications by members. The question of licensing of engineers was brought up, and the consensus of opinion among the membership was asked for. Because the matter is controversial, no official action has been taken and it was suggested that the' local and State sections act separately in this regard. A. B. Parsons, the assistant secretary, next spoke. In his remarks he indicated surprise that many prominent mining men still did not belong to the Institute, and urged that section delegates make up a list of such prospective members and send it in to the office for study by the New York staff. He also asked that re- ports of all meetings be turned in for publication in MINING AND METALLURGY, and said that the reports

Jan 1, 1930

By M. J. Pool, with Appendix by Larry Kaufman, R. W. Krenzer

Thermodynmic properties of the Cu-Mn system have been deterrrzined in the temperature range 973" to 1273°K by measuring the vapor pressure of manganese in equilibrium with alloys of compositions varying from 0.13 to 0.91 rnole fraction manganese using the Knudsen effusion technique. Activities of manganese calculated from the measured vapor pressures show large positive deviations. Calculated heats and entropies of mixing are positive with a maximum occurring at approximately 0. 7 mole fraction manganese. ThE investigation of thermodynamic properties of binary systems involving transition metals is of considerable interest at the present time. The incomplete subvalency electron levels of transition metals lead to unusual behavior in some alloys, and considerable information can be obtained by determining the thermodynamic characteristics of these systems and relating the thermodynamic behavior to observed physical properties. The Cu-Mn system, shown in Fig. 1,' provides an example of an alloy system in which the determination of the equilibrium phase diagram and various physical properties has received considerable attention, but very little work has been done on measurement of the thermodynamic properties. Elemental copper and manganese have comparable electronegatives, atomic sizes, and cohesive energies, but differ in crystal structure. They form a continuous series of solid solutions only at high temperatures and the structure varies in a continuous manner from fcc at the copper-rich end to fct at the manganese-rich end.' The purpose of this investigation was to measure the vapor pressure of manganese over a series of Cu-Mn alloys and from these values determine the thermodynamic properties of the binary system. Vapor pressure measurements were made in the temperature range 973" to 1273"K, remaining within the solid-solution region for each alloy studied. EXPERIMENTAL PROCEDURE The relative thermodynamic properties of solid Cu-Mn alloys were determined from vapor pressure measurements by means of the Knudsen effusion tech- nique. Several discussions of the theory can be found in the literature. In the case of copper and manganese, it is assumed that manganese is the only component subliming, so the vapor pressure of manganese over the various alloys can be determined directly by measuring the weight loss of the effusion cell. This is a valid assumption since the vapor pressure of manganese is about four orders of magnitude higher than the vapor pressure of copper in the temperature region of interest. The vapor pressure of manganese over the alloys at any given temperature is then related to the weight loss of the effusion cell per unit area per unit time. An upper limit of 1.5 x 10"s has been measured for the ratio of polyatomic to monoatomic molecules for manganese vapor in equilibrium with solid manganese at 1180°K, so it was assumed that manganese vapor is monoatomic. The effusion cells, fabricated from high-purity alumina, are 26 mm high, 18 mm OD, and have a wall thickness of 1 mm. Three different sized holes of 2.03, 2.54, and 3.18 mm diam were drilled in the lids from the inside face to minimize chipping, and the lids were then slip-cast onto the cells to provide a gas-tight seal. Alumina was selected for this particular application both because of its resistance to thermal shock and reaction with manganese vapor. In the ideal case, the orifice of the effusion cell should have a knife edge so that effusion through the orifice

Jan 1, 1970

By W. E. Hess

AT the Vesta mines of Jones & Laughlin Steel Corp. on the Monongahela River, 35 miles south of Pittsburgh, JCM Joy continuous miners and 6-SC shuttle cars are used for pillar extraction in the Pittsburgh seam. The entire output of the mine goes into coke production for blast furnace operation. Because this coal, which has high metallurgical qualities, is close to the place where it is ultimately used and because supplies with these properties are being rapidly depleted, complete recovery is essential wherever possible. With the introduction of the continuous miner into the Vesta mines, therefore, it was necessary to plan a project which would facilitate development and provide for future total recovery. Use of continuous miners under varying conditions has necessitated changes with regard to roof action, method of development, method of pillar attack, and innovations in mining. In the following pages these changes will be discussed. Prior to the introduction of continuous miners the Pittsburgh seam at the Vesta mines averaged 72 in. of mineable coal, overlain with 12 to 16 in. of draw-slate, which weathers on exposure to air and is not firm enough to be held in place. Immediately overlying the drawslate is a wild or rooster coal, very irregular in thickness, varying from 12 to 30 in. Above the rooster coal the strata consists predominately of shales or lime shales and sandstone. Just before the introduction of continuous miners in the Vesta mines, however, a definite change took place in the character of the roof structure overlying the coal seam, see Fig. 1. Thickness of laminated roof immediately overlying the rooster coal varies with localities and introduces a problem in roof control. In fact, a set of eight main entries being developed in Vesta NO. 4 mine entered an area with so difficult a roof structure that management considered abandoning the section altogether. In this locality the roof consisted of thin alternate layers of roof coals and shales, with an occasional irregular seam of slick slate, the whole being laced with slips, and the coal itself being cut by clay veins and spars. In an effort to overcome some of the difficulties, roof bolting was introduced in 1949. This made it possible to recover coal from an area which otherwise would have been economically unmineable. There have been very few roof bolt failures. When conventional machines were replaced by continuous miners there were changes in the development of butt entries. By these changes it was hoped: 1—to speed development, 2—to provide as much solid coal as possible for the machine on retreat, 3—to avoid the necessity of crossing entries already driven, 4—to facilitate ventilation, 5—to provide a roadway for shuttle car haulage which would eliminate the necessity of running through doors or curtains, 6—to provide better roof control by increasing the distance between the center lines of entries, and 7—to provide more coal when the machine was in position to load.

Jan 1, 1956

By D. R. Parrish, T. M. Geffen, R. A. Morse, G. W. Haynes

Flow tests on small core plugs have indicated that a large amount of gas is trapped and not recovered by water flooding a gas sand. Instead of I to 15 per cent pore space, as is usually assumed, the residual gas saturation is 15 to 50 per cent pore space, and is thus of the same magnitude as residual oil after water flooding oil sands. A thorough investigation was made to ascertain that large amounts of residual gas actually remain in reservoirs after a water flood and that this condition is not merely a laboratory phenomenon. In field experiments, the amount of gas left in a watered-out gas sand was measured by use of a pressure core barrel and the residual gas saturation of two watered-out gas sands was determined by electric log evaluation. In the laboratory, an investigation was made of factors that could possibly cause the value of residual gas saturation as measured on small core plugs to differ from that in the reservoir, and the effect of these factors on the amount of residual gas saturation was studied. The factors studied include flooding rate, static pressure, temperature, sample size and saturation conditions before flooding All evidence established that a relatively high gas saturation is trapped in water flooded gas sands and that this residual gas saturation can be measured in the laboratory by tests on small core plugs. INTRODUCTION There. has been general agreement among engineers that very high recovery of gas could be obtained from natural reservoirs By water displacement. Gas recoveries of 80 to 95 per cent of the original gas in place have become the normal expectation in water drive fields. The assumption of high recovery has been based on: 1. low density and viscosity of gas compared with water; 2. the erroneous assumption that the flow relationship in a gas-liquid system where gas is the displaced phase will be the same as when it is the displacing phase. It has long been recognized that gas can flow at very low gas saturations (in the range of 1 to 15 per cent pore space) in systems where liquid is being displaced by gas. By assuming the reversibility of this process, the conclusion was reached that the residual gas saturation following water flooding of a gas reservoir would be the qame (1 to 15 per cent) as that at which gas first flowed continuously as a displacing phase. Recent laboratory relative permeability Studies have demonstrated that the flow characteristics are very different in gas-liquid systems, depending on whether gas is displacing or being displaced by, a liquid. Also, it has been shown that there is no difference between the flow characteristics of oil and water or gas and water in water wet porous rocks. The residual gas saturation that can be expected following water flooding of a gas reservoir then would be in the same range as the residual oil saturation normally expected after water flooding an oil reservoir! i.e., in the range of 15 to 50 per cent pore space, depending on the rock characteristics. Obviously, such a difference in residual gas saturation means very important differences in recoverable gas reserves from water drive reservoirs. For example, if the original gas saturation in a field were 70 per cent, and the residual gas following flooding were 35 per cent, only half of the gas in place could be recovered by complete water drive, compared to the previously expected 80 to 95 per cent. This is a situation in which complete pressure maintenance could result in very greatly reduced recovery, since straight pressure depletion recoveries from gas reservoirs can approach 80 to 90 per cent. Such a change in thinking must be based on more complete information than a series of small core tests. Hence the work reported herein was undertaken with the objective of determining whether or not residual gas saturations indicated from small core relative permeability tests at atmospheric pressure and room temperature are representative of the residual gas saturations which could be expected after water flood of natural reservoirs. A study was made both through laboratory and fields tests to determine any differences in residual saturation which might be occasioned by differences in pressure, temperature, rate of flooding, and original saturation conditions. Four separate types of laboratory experiments and two field mesurements were made in this investigation. The apparatus and testing methods of each will he discussed individually. LABORATORY EXPERIMENTS, APPARATUS AND PROCEDURE Relative Permeability Tests Steady state flow experiments Here conducted using the Penn State type apparatus. The equipment used has beer (described in a previous publication? "Irreducible" water satu-ration was established in the core' by imposing ,a capillary pressure of 45 psi before simultaneous flow of air and water

Jan 1, 1952

By Walter B. Devereux

Metallic copper is a product of native metallurgy in various parts of Mexico, and by somewhat varied processes. While recently examining copper mines in the State of Jalisko, I had an opportunity of witnessing Mexican copper smelting by a process which I have not seen described, and which is interesting from the fact, that a fine quality of copper is produced from sulphurous ores in three metallurgical operations, and apparently without excessive loss. The process was carried on in buildings which were part of a plant erected by an American more than twenty-five years ago for the purpose of smelting and working copper. After a few years this man met with accidental death, and the works have been but little used since. Located in the centre of a high range of mountains, far from any town or seaport, and inaccessible except over difficult mule trails, these substantial buildings, filled with furnaces and heavy machinery,

Jan 1, 1883

By Donald R. Rathburn, Jung K. Mok

An historical review and a survey of current practice in the application of fine dry grinding in the iron ore industry are given. Both closed and open-circuit applications are reviewed, and the advantages, disadvantages, and process considerations for these two systems are discussed. The ground ore temperature rise, and the cool-ing of ground ore and mill ventilation are also discussed, along with the agglomerating characteristics of dry ground ore. Screening during the production of high-grade lump ore for blast-furnace burden, particularly from recently developed ore deposits in Australia, South America, and Africa, has resulted in large tonnages of fine iron ore. Certain owners have decided to stockpile these fines until some later date. Others have either sold these fines "as is" for agglomeration at the steel plant or have established their own pelletizing plants to produce a premium quality agglomerate. In almost all cases some grinding is required prior to pelletizing. Most of these ores occur in the weathered state which may result in difficulty in the thickening and/or filtering stages when ground in a wet system. The resulting filter cake would probably require partial drying to provide a product suitable for the subsequent balling operation; however the partial drying and subsequent material-handling steps often produce random agglomeration. Normally, these agglomerates will cause problems in the green ball formation process. Thus dry grinding has developed as a solution to this problem. Most of the dry iron ore grinding installations utilizing the standard-type rod or ball mill are grinding high-grade natural ores that do not require beneficiation. Although power consumed per ton of final product is 120% or greater in dry grinding as compared with wet grinding, the additional power required for dewatering and handling a wet ground product can easily exceed the initial power savings. Dry grinding of raw feed and clinker has been practiced in the cement industry for many decades but its major application to the iron ore industry has taken place only within the past ten years. The successful application of dry grinding to iron ore has required the solution of several unique design and operating problems. The purpose of this paper is to review recent developments in fine dry grinding of iron ore for pelletizing and to discuss the various designs and operating parameters involved.

Jan 1, 1971

[Steel, iron which is malleable at least in some one range of temperature, and in addition is either (A) cast into an initially malleable mass ; or (B) is capable of hardening greatly by sudden cooling ; or (C) is both so cast and so capable of hardening. Variety A includes also molten iron which, if cast, would be malleable, as do its two sub-varieties, "ingot-iron" and "ingot-steel." (Tungsten-steel is malleable only when red-hot.)] does not seem to fit perfectly the requirement that it shall include all known varieties of steel and exclude everything else. The first requirement, that it shall be malleable at some temperature, is also possessed by some varieties of gun-iron—that is, mottled castriron, of which cannons have been made in the past by the South Boston Iron Co. and others. Gun-iron also meets the requirement (A) in being cast into an initially-malleable mass. The malleability was indeed not great, nor mas it made use of except to demonstrate the quality of the iron, but it approached in measurable degree that of some of the alloy-steels. As for requirement (B), some puddled-irons having from 0.2 to 0.3 per cent. of carbon may be hardened greatly, although this property is [lot utilized.

Jan 1, 1909

By George H. Ashley

The present critical state of the supply, distribution, and utilization of coal and the necessity for pooling and zoning coals calls renewed attention to the lack of any fully adequate classification of coal. In the past coals have been classified as anthracite, semianthracite, semibitumi-nous, bituminous, subbituminous coals, and lignite, and a few special types, such as splint coal and cannel coal. But under the term bituminous coal are included a great variety of coals differing markedly both physically and chemically. The term subbituminous coal covers as great a range of chemical differences. In order to distinguish these varieties of bituminous coals it has been customary to designate coal by names derived from the place where mined, or by the name of the bed from which it is mined. Thus, in the market reports, coals are quoted as Pocahontas coal, New River or Sewell coal, Moshannon coal, Ohio coal, Williamson County coal, Jellico coal, and so on indefinitely, no limit being set as to the boundaries of the area to which a given name is applied. Nor is there any scale by which the coal from one place may be compared with the coal from some other district or some other bed. On the one hand, coals from the same district may be quite distinct and sell at very different prices or coal from the same bed may differ greatly in different districts; on the other hand, coals from different states may be so similar physically and chemically that one could replace the other in practical use without any appreciable difference in service. The following classification, arrived at after a careful review of a large number of systems of classification and of all of the recognized characteristics of coal, brings together all coals that so nearly resemble each other physically, chemically, and in heating qualities that any coal of a given type could replace any other coal of the same type and grade in use. Thus, if coals A and B are classed as of the same type and grade they have, so far as known to the writer, approximately the same heating value when burned under the same conditions, and the same character, length of flame, and properties affecting transportation and stocking; and if of the same grade, approximately the same percentage of impurities.

Jan 1, 1920

By Charles G. Yale

(San Francisco Meeting, October, 1911.) A FEW years ago somebody connected with one of those self-constituted bodies of unofficial character, like a Chamber of Commerce, Board of Trade, or State Development Board, started a catch-phrase referring to California as " The Land of Sunshine, Fruit, and Flowers," and the railroad magazines and folders keep it steadily in use, working day and night. Yet it altogether ignores the substance which brought the State into the Union, which peopled it, and which made it famous through-out the world. You ladies and gentlemen who have come from what we here call "the East," have in your own States, no matter which one, sunshine, fruit, and flowers. But your Eastern States, having these things as we do, have not the gold that we do. Therefore, the old designation of "The Golden State," applied to California, should be revived, as being the most distinctive term. It is worthy of remembrance, too, that during the dark days of the civil war this State handed over $172,000,000 in yellow gold, and saved the credit of the nation. Gold-mining has been carried on in California since " The days of old, The days of gold, The days of 49," and it still continues. Since that historic year, and up to the end of 1910, the State has produced, in gold alone, $1,530,214,468. Since 1792 the entire United States production of gold has been $8,261,573,500, so that the single State of California has, in that period, produced within $201,144,564 of one-half of all the gold from Alaska, Arizona, Colorado, Idaho, Montana, Nevada, New Mexico, Oregon, South Dakota, Utah, Washington, and the Southern and scattering States. In other words, all the other 25 gold-producing States of the United States combined

Mar 1, 1912

By E. Gybbon Spilsbury

(Pittsburg meeting, March, 1910.) THE recovery of gold and silver from their ores by means of the cyanide process has been so successful in the last few years that any radical improvement would seem impossible; yet the appliance to which I wish to call attention in this paper is really a radical departure from the methods now in general use. The most modern and approved of these, known as the all-sliming method, depends for its success on the grinding of the. ore so fine that practically 90 per cent. of it will pass through a 200-mesh screen. The slimes thus produced are then agitated and aerated in tanks of various types. The main object of this treatment is to insure such a thorough admixture of the pulp and solution that every particle of the ore is surrounded by a volume of solution sufficient to insure the dissolving of the whole of the gold- and silver-content. In addition, in order to expedite the action of the cyanide, and to oxidize such elements as would, if left in their active state, become cyanicides, air is blown in under pressure. In the Pachuca tank, this air is the active and sole means of agitation. The chief objections to all the methods off agitation used heretofore are the expense of operating and maintaining the mechanical devices for keeping the pulp in suspension, and the length of time required to obtain a fairly complete extraction. of the values. These objections are inherent to any method of agitation effecting a circulation of the pulp and the solution together, by giving the whole mass a circular movement, as in the low-tank system, or a vertical circulation, as in the Pachuca-tank system. In both methods, the particles of ore are kept traveling in the same direction as the solution, and with very little difference of speed; so that, while the whole mass is in

May 1, 1910

By Dwight L. Sawyer

IF it had not been for the testimony of former Secretary of the Interior, Harold L. Ickes, before the Senatorial investigating committee the public would have heard little about the Federal Government's suit against California for the ownership of the tidelands. The Ickes-Pauley dispute brought to public attention that the California tideland oil deposits are the last remaining large Federal oil reserves. Ickes contends that these tideland oil deposits belong to the nation for the benefit of all the people of all the states and not solely to the State of California. Ickes also accused California oil man Ed Pauley of offering to give $330; 000 to the Democratic party fund if Ickes would drop the Federal Government's suit against the State of California for the ownership of said tidelands. The tidelands may be considered as the land bordering the coast line between mean high tide and outward under the ocean for a distance of a marine league, or about three statute miles. This strip of land along the coast of southern California contains large oil deposits which have a present and future prospective value of several billion dollars.

Jan 1, 1947

By Gilbert Soler

THIS year's Chairman of the Iron and Steel Division is a noted member of a small and select group of practical scientists now working in this country and in Canada to improve the production and properties and to reduce the cost of super-quality carbon and alloy steels; he is one of those all-important leavening agents-a man with his feet always on the ground but capable of putting his head into the clouds on occasion-that are so necessary in applying science sensibly to the practical problems of steel production. He is equally at home in a discussion of the free energy of deoxidizing reactions or the entropy of the formation of stable sulphides, and in a consideration of the relative advantages of the basic-electric and the open-hearth furnace for the production of rimming steels in the Detroit area. Gilbert Soler was born of American parents in Havana, Cuba, just forty years ago. He graduated as a ceramic engineer from Ohio State University in 1930 and received a Master of Science degree a year later. In 1940 he received the degree of metallurgical engineer from the same institution.

Jan 1, 1948

By James A. Crookston, William D. Fitzpatrick

Committee C-8 of the American Society for Testing and Materials defines "Refractories" as "Material, usually nonmetallic, used to withstand high temperature," and it defines the term "Refractoriness" thus, "In refractories the capability of maintaining the desired degree of chemical and physical identity at high temperatures and in the environment and conditions of use." The ability to withstand high temperatures is critical to classifying a material as a "refractory." However, as the foregoing definition of "refractoriness" implies, the refractory material may be subjected to and is expected to resist not only high temperatures but a variety of other destructive forces incident to its use. These include abrasion, impact, thermal shock, chemical attack, and high level loads at high temperatures. The various industrial applications of refractories represent an infinite variety of combinations and degrees of severity of these destructive forces, including high temperatures. Naturally, such a variety of application conditions leads to a need for a wide variety of refractory products to satisfy those conditions. The number of refractory products available is great enough that some form of classification is necessary to a discussion of refractories. Refractories may be classified in several ways, but the most suitable one is based on their general compositions and to lesser degrees on their physical condition and distinctive properties. The primary types of brick include aluminosilicate brick (fire clay and alumina), basic brick (magnesia and chrome ore, alone and in various combinations), silica brick, insulating brick, and special refractories (carbon, Sic, ZrO,, zircon, borides, and nitrides). Brick are, of course, preformed and are usually heat treated at high temperatures before use, but are in some instances unburned and/or chemically bonded, including the relatively new class of tar-bonded magnesia and/or dolomite brick. In addition to preformed refractories, another broad category includes the so-called specialty refractories, which are usually made in the same types as itemized for brick-bonding mortars and high temperature cements, hydraulic setting castables or refractory concrete, plastic firebrick, and ramming mixes. Refractory grains, such as fire clay and high alumina calcines, dead-burned magnesite and periclase, and dead-burned dolomite are also considered refractory products. Brick are also classified on the basis of physical dimensions, as standard sizes and special shapes. The standard sizes are those which are of definite shape and design and are designated as 9 x 4 ½ x 2 ½ in. and 9 x 4 ½ x 3 in. straights and series. All other brick of non- standard sizes are referred to as special shapes. These come about as a result of a particular need for a given furnace or for a particular application.

Jan 1, 1975