Search Documents

By N. M. Langdon

INTRODUCTION. IN considering the magnificent success of Mr. Gayley's Bold experiment of applying dry blast to the blast-furnace, whereby , saving of 20 per cent. of fuel per ton of iron is effected, the question arises whether, still further economy in fuel is possible, and, if so, how it is to be attained? The manner in which the heat generated in the furnace is utilized in the production of pig-iron may be determined, by the method of Bell and Gruner, for any furnace for which the necessary data are obtainable ; and the study of the operation,. tinder various conditions, of a number of furnaces, for which such information has been worked out., should enable us to form some conclusion on the subject. The tables and calculations given below cover the operations of several furnaces reported in our Transactions; also the two furnaces using natural and dry blast in ,Mr. Gayley's experiment, for which the heat-equation has been worked out by Prof. Joseph W. Richards in his admirable discussion' of Mr. Gayley's paper, The Application of Dry Air Blast to the Manufacture of Iron, and, finally, various hypothetical furnaces.. The full list is as follows : A. Isabella furnace, with natural blast. B. Isabella furnace, with dry blast. The data stated. for A and B in Table III. are those given by Professor Richards; except that the heat-units are given for one unit of iron instead of 100 units, and some items of heat supplied, as stated by Richards, have been subdivided, the total being the same as given by Richards. (Columns A and B are introduced in Table III. for comparison with C and D.)

Oct 1, 1909

By J. R. Long, R. S. Dean, F. S. Wartman, E. T. Hayes

The production of titanium in I5-lb. lots and with a purity sufficient to be consolidated into ductile metal, as described in a previous paper,' has provided adequate material for a study of the physical properties of titanium and a more thorough examination of its working qualities. Data on the physical properties reported in that paper were obtained on metal fabricated by a fixed procedure, standardized for the purpose of control of the reduction, and are representative only of material fabricated under those conditions. There are many possible variables in the working schedule, which will have significant effects on the properties of the finished material; and since the previous working methods were not necessarily the best, an investigation of the fabrication of titanium by other methods was undertaken. In this work the consolidation of the powder by pressing and sintering was conducted essentially as outlined in the report cited' and all efforts were centered on fabrication methods for those powders and the proper- ties produced by them. Hardness, density, microstructure, and tensile properties were determined at various stages in the working and annealing; and resistivity measurements were made on a few bars and drawn wire. Consolidation of the PowdeR The screen analysis of the available titanium powder is given in Table I. No attempt was made to alter the size distribution from that noted because this powder, although coarse by normal powder-metallurgy standards, produced acceptable compacts suitable for the present work. Because of their large specific surface, finer powders are more contaminated by oxygen and produce harder compacts, which are difficult to work. The powder as produced is soft, compresses in a normal fashion, and exhibits very little tendency to adhere to the die surfaces. Unlike aluminum and magnesium powders, it can be readily pressed without the use of die lubricants. When compacted at 50 tons per

Jan 1, 1946

By J. R. Long, E. T. Hayes, R. S. Dean, F. S. Wartman

The production of titanium in I5-lb. lots and with a purity sufficient to be consolidated into ductile metal, as described in a previous paper,' has provided adequate material for a study of the physical properties of titanium and a more thorough examination of its working qualities. Data on the physical properties reported in that paper were obtained on metal fabricated by a fixed procedure, standardized for the purpose of control of the reduction, and are representative only of material fabricated under those conditions. There are many possible variables in the working schedule, which will have significant effects on the properties of the finished material; and since the previous working methods were not necessarily the best, an investigation of the fabrication of titanium by other methods was undertaken. In this work the consolidation of the powder by pressing and sintering was conducted essentially as outlined in the report cited' and all efforts were centered on fabrication methods for those powders and the proper- ties produced by them. Hardness, density, microstructure, and tensile properties were determined at various stages in the working and annealing; and resistivity measurements were made on a few bars and drawn wire. Consolidation of the PowdeR The screen analysis of the available titanium powder is given in Table I. No attempt was made to alter the size distribution from that noted because this powder, although coarse by normal powder-metallurgy standards, produced acceptable compacts suitable for the present work. Because of their large specific surface, finer powders are more contaminated by oxygen and produce harder compacts, which are difficult to work. The powder as produced is soft, compresses in a normal fashion, and exhibits very little tendency to adhere to the die surfaces. Unlike aluminum and magnesium powders, it can be readily pressed without the use of die lubricants. When compacted at 50 tons per

Jan 1, 1946

By M. O. Holowaty, C. M. Squarcy

Blast furnaces are the tools of men, and it is men who have made them great. Here is presented the story of the Ironmakers-the men who first poured hot metal into what would someday be the sinews of a nation. W HEN the Jacobean merchant adventurers bade farewell to the first ship of colonists sailing for the new land, they instructed them to direct all their skill and energy to grow silk worms in Virginia. The adventurers felt sure that they could flood the market with highly priced and much desired goods like silk, sugar, tea, and indigo. They were also convinced that they would fill the needs of the mother country for iron. Early iron production in the colonies The merchants certainly had a wonderful imagination, for silk and indigo were just as exotic in Virginia as they were in England. The settlers found it more profitable to raise tobacco on the vast stretches of the free, fertile land. Thus the plans of settlers clashed with those of The Virginia Co.; and only point of agreement was the desire to produce iron. But, even there the motives of the settlers and those of The Virginia Co. of London were worlds apart. The settlers wanted to produce the tools badly needed in the colony, while the Company desired to cash in on the rising demand for iron which the home industry could not satisfy. Both the settlers and the Company lost no time trying to find iron ore. Locations of the early mines are not known. If, however, the reports of the Irishman, Francis Maguel, can be trusted, as early as 1609 a ship sailed for England with a load of 17 tons of crude iron which the East India Co. purchased at £ 4 per ton. The iron was of excellent quality and considered the best iron made of non-English ore that was ever purchased.

Jan 1, 1961

By Rollin Farmin

"SWELLING GROUND" delivers pressure on mine timbers that originates in expansion of the wall rock, whereas "heavy ground" delivers only gravitative pressure. Of the several possible causes considered, the swelling is attributed to the physical surface action of water on gouge and flaky rocks at the periphery of the mine opening.

Jan 1, 1944

By Ogden Tweto

The classes of ore deposits in the mountain province of Colorado that have been the most productive in the past and that offer the greatest promise for the future are: (1) disseminated or stockwork molybdenum deposits associated with Tertiary stocks; (2) combination precious- and base-metal veins in Tertiary volcanic rocks; and (3) base-metal replacement deposits and veins in Paleozoic sedimentary rocks. Veins in Precambrian rocks, including precious metal-bearing sulfide veins, gold-silver telluride veins, and tungsten veins, have been mined extensively in the past, but their aggregate output has been far subordinate to that of the groups named above, and the outlook for major output from them in the future is poor. Principal ore deposits of south-central Wyoming are sedimentary iron ores of Precambrian age and uranium deposits in Tertiary sedimentary rocks. Precambrian deposits of several kinds are scattered through the mountains of both states. The most promising of these, based on present indications, are vanadiferous titaniferous magnetite in southern Wyoming and southwestern Colorado and thorium-niobium rare-earth deposits associated with alkalic intrusive complexes in Colorado. Most of the mining districts of Colorado are in the Colorado mineral belt, a generally narrow but somewhat irregular belt that extends northeastward across the north-trending mountain ranges and the north-northwest trending geologic grain of the state. The belt is characterized by intrusive rocks of Laramide and younger age and by ore deposits, and it occupies environments ranging from Precambrian crystalline rocks through Paleozoic and Mesozoic sedimentary rocks to Tertiary volcanic rocks. Two ages of intrusion and ore deposition recently have been recognized in the mineral belt. One is Laramide (late Cretaceous and early Tertiary), and the other is Oligocene. As interpreted herein, the major replacement deposits and most of the sulfide vein deposits in Precambrian and sedimentary rocks are Laramide in age, and the molybdenum deposits, the tungsten and the gold telluride veins in Precambrian rocks, and the precious- and base-metal veins in volcanic rocks are Oligocene in age. In general, the Laramide deposits are mesothermal in aspect, and the Oligocene deposits are principally epithermal. The existence of two mineralization stages, in considerable part characterized by different suites of metals, has many applications in exploration.

Jan 1, 1968

By R. D. Parker

LARGEST of any hoist installation ever manufactured in Canada is that being erected at No. 5 shaft, Creighton mine, of the Inter- national Nickel Company of Canada, Limited. It is a bicylindrical conical- drum hoist with the drums arranged in tandem, and driven by two direct- current motors through single reduction gearing. This hoist was designed by the Canadian Allis-Chalmers, Limited and manufactured at their works in Lachine, Quebec.

Jan 1, 1936

By W. E. Showalter

This paper discusses some of the results of combstion-drive tests which were made in a test cell using a sand bed 10 in. in diameter x 10-ft long. The test method is illustrated and described. The relationship between the API gravity of the in situ oil and the amount of air required for combustion drive is discussed in detail. Other things constant, the air requirement for combustion drive increases as the APl gravity of the in situ oil decreases. If the test results apply to actual reservoirs, the lowest-priced oils may cost the most to recover by this method. Information is shown which indicates that the effect of pressure on the amount of hydrocarbon burned is not large. A method of predicting air requirements from the API gravity of the in situ oil is presented. INTRODUCTION Combustion drive is the term used to identify the process of interstitial or in situ burning as an oil recovery method. Part of the in situ oil is burned to generate the energy needed to produce the remainder of the oil. Combustion drive as an oil recovery mechanism remains an economic uncertainty in spite of all the work that has been done by the industry in both laboratory and field?-6 This paper will show some of the results of tests which were made in a test cell for the purpose of studying the nature of the combustion-drive process. It will present data which indicate that the API gravity of the in situ oil is a significant indicator of the amount of air required to drive a burning front through oil sand. Air requirement varies inversely as the API gravity of the in situ oil. EXPERIMENTAL The tests were performed in a cell which utilized a cylindrical sand section 10 in. in diameter x 10-ft long. The thin-walled metal pipe which held the sand was wound with twenty external electrical resistance heaters which, by means of an automatic controller, maintained adjacent sections of the wall of the pipe at temperatures equal to the temperatures of the contained sand. Each heater covered 6 linear in. of the pipe. By this means lateral heat loss from the sand section was minimized, thereby causing the sand section to simulate more closely a horizontal increment of a combustion-drive reservoir. Fig. 1 shows a schematic diagram of the test assembly. Thermocouples to measure the temperature in the sand were located every 6 in. along the length of the sand section. The pipe containing the sand was enclosed in a cell designed for an operating pressure of 500 psig. The inlet air pressure was controlled at the inlet, and the gas flow rate was controlled and measured at the outlet of the cell. The oil sand used for the tests was prepared by mixing first water and then oil with the noncon-solidated sand using a closed mixer similar to a cement mixer. Table 1 shows a screen analysis of the sand. Ninety percent of the sand was 100 mesh or finer. This sand was a mixture of 80 per cent No. 120 Nevada White Sand and 20 per cent Tennessee Hi-Fusion Moulding Sand No. 3. The Nevada sand was a clean silica sand. The Tennessee sand con-

Planning for a surface coal mine includes selecting the best means and equipment for uncovering the coal, loading it, and transporting it to the preparation plant. The machines and methods that will ensure optimum production will depend upon the location and characteristics of the seam to be mined. Stripping Techniques The choice of stripping units is influenced primarily by the system of mining, such as contour or out-crop mining as contrasted to mining in a region of rolling terrain with relatively flat upland surfaces. Factors such as the life of the mining operations production requirements, types of overburden, local and regional dip of coal, and land reclamation are other important considerations.

Jan 10, 1967

By E. R. Gilbert

Klopp et al. have reported data on tensile and creep properties of are-melted and electron-beam-melted tungsten. We would like to point out some similarities between their creep results and ours on are-melted and powder-metallurgy tungstenand offer some alternate interpretations of the data which lead to different rate-controlling mechanisms. Klopp et al. observed extensive transient creep in the 2250" to 3500°F temperature range where the acthetivation energy is 106,400 ± 3300 cal mole-1. They suggest cross slip as the possible rate-controlling mechanism since "cross slip may occur only by the movement of screw dislocations, and not edge dislocations, thus allowing only partial recovery of the strain hardening and resulting in a continuously decreasing creep rate, characteristic of transient creep.'' Our tests on are-melted tungsten and powder-metallurgy tungsten displayed an extensive transient creep stage in the same temperature range but they also displayed a steady-state creep stage. The stress levels and strain rates of the two investigations, 1.4 to 7 kg mm-2 and 10-7 to 10-4 sec-1 for that of Klopp et al. and 4.5 to 10 kg mm-2 and 10-8 to 10-4 sec-1 for those of Gilbert et al., are overlapping. The activation energy for creep of our powder-metallurgy tungsten is 105,000 cal mole-1. This close agreement with the value found by Klopp et al. suggests that the same mechanism may be common to both types of materials. It may be possible to gain some additional insight into the rate-controlling mechanism by applying the analysis made by conrad22 in terms of the activation volume. The value for the activation volume depends upon the dislocation mechanism and may be used to help differentiate between various dislocation mechanisms. The activation volume for cross slip is 10 to 100 b3. Values determined from our data were 130 to 220 b3 which are in better agreement with the range of 102 to 104 b3 for nonconservative motion of jogs. Values determined from data of Klopp et al. are 240 to 1040 b3. We suggest that the rate-controlling mechanism for creep in this temperature range may be nonconservative motion of jogs assisted by enhanced diffusion along grain boundaries or dislocations. This model requires an activation energy lower than that for self-diffusion as is observed. If this is the controlling mechanism, a higher activation energy which is closer to that for self-diffusion might be expected for tests conducted on specimens with reduced grain boundary area, i.e., larger grain size. In support of this premise we have conducted tests on speci- mens having one to three grains per cross section for which a higher activation energy of 130,000 cal mole-1 was observed. Also, in agreement with results of Klopp et al., a faster creep rate resulted from the increased grain size and probable decreased dislocation density. Further argument against the cross slip mechanism is based on the constant activation energy we obsserved over the range of 5.0 to 10 kg mm-2,21 whereas the activation energy for cross slip displays a significant stress dependence.23 In addition to this, the powe on the stress term for the strain-rate dependence appears too high for cross slip. The values for tungsten fall in the range of 4.5 to 7 (Klopp et al. and Ref. 21) whereas values of approximately 2 are observed in creep by cross slip for hep metals.24 At temperatures from 3300° to 4000°F, Klopp et al. observed an activation energy of 141,000 ± 4000 cal mole-' which is less than that for self-diffusion, 153,000 cal mole-1, 25 and less than that reported for high-temperature creep of powder-metallurgy tungsten by Green:' 160,000 cal mole-1. Klopp et al. suggested that recovery of strain hardening by dislocation climb is the rate-controlling mechanism in this temperature region. Actually an activation energy larger than that for self-diffusion is predicted by this model if the temperature dependence of the elastic modulus27 is taken into consideration. Klopp et al. attributed this lack of correlation to the compositional differences between powder-metallurgy tungsten used by Green and their own arc- and EB-melted tungsten. It is our position that the value of 141,000 ± 4000 cal mole-' represents a transitional value between the higher and lower activation energies and does not represent a discrete mechanism of deformation. If the tests had been extended to higher temperatures the higher value of activation energy would have been observed as has been demonstrated by both our analy sis'' of isothermal test data by GE-NMPO28 and differential temperature tests28 on are-melted tungsten. The activation energies determined (170,000 and 160,000 cal mole-1) were greater than that for self-diffusion and are in better agreement with the value found by Green. The model of dislocation climb is associated with ; activation volume of 1 b3 according to Conrad.22 The activation volume calculated for the creep data of fou independent investigators in the temperature range where the activation energy for creep is near that for self-diffusion (Klopp et al. and Refs. 26, 28, and 30) is 110 to 2800 b3 and is in the range suggested for nonconservative motion of jogs. In the case of tungsten this mechanism may be preferred over that of dislocation climb. Sincere appreciation is expressed to Messrs. J. E. Flinn and F. L. Yaggee for the helpful discussions and suggestions in the preparation of this communication.

Jan 1, 1967

THE Institute assembled on Tuesday evening, October 24th, in the hall of the Franklin Institute, Mr. Frank Firmstone, VicePresident, in the chair. Mr. J. Price Wetherill, of Tremont, Pa., read a paper on An Outline of Anthracite Coal Mining in Schuylkill County, Pa. The paper was discussed by Messrs. Coxe, Rothwell, Heinrich, Harden, and Symons. The second session was held on Thursday evening. Mr. A. L. Holley, Chairman of the International Committee, appointed by the Institute to consider the nomenclature of iron and steel, offered the following report of the committee, signed by all the members: WHEREAS, The recent production of soft, cast, malleable compounds of iron by the Bessemer, the Siemens-Martin, and the crucible steel processes appears to demand a new nomenclature of iron compounds, for the following reasons: 1st. The term "steel," by which these soft products are commercially and professionally designated in England and in the United States, does not completely distinguish them from previously existing "steel which would harden and temper. 2d. A nomenclature recognized in all languages seems desirable, as well for commercial as for scientific purposes, especially as lawsuits, already commenced, depend on the meaning of the term " steel." 3d. Although homogeneity, due to fusion, is usually recognized, and is by this committee recognized as the most definite characteristic of both hard and soft steel, this quality may be equally well expressed in other terms, thus leaving the old term, " steel," to define the malleable compounds of iron, which will harden and temper. Therefore, resolved, That this committee recommends the following nomenclature : 1. That all malleable compounds of iron with its ordinary ingredients, which are aggregated from pasty masses, or from piles, or from any forms of iron not in a fluid state, and which will not sensibly harden and temper, and which generally resemble what is called " wrought iron," shall be called Weld Iron (German, Schweisseisen; French, fer soudé). 2. That such compounds, when they will from any cause harden and temper, and which resemble what is now called puddled steel," shall be called Weld Steel (German, Schweiss stahl; French, acier soudé).

THE Institute assembled on Tuesday evening, October 24th, in the hall of the Franklin Institute, Mr. Frank Firmstone, Vice-President, in the chair. Mr.. J. Price Wetherill, of Tremont, Pa., read a paper on An Outline of Anthracite Coal Mining in Schuylkill County, Pa. The paper was discussed by Messrs. Coxe, Rothwell, Heinrich, Harden, and Symons. The second session was held on Thursday evening. Mr. A. L. Holley, Chairman of the International Committee, appointed by the Institute to consider the nomenclature of iron and steel, offered the following report of the committee, signed by all the members: WHEREAS, The recent production of soft, cast, malleable compounds of iron by the Bessemer, the Siemens-Martin, and the crucible steel processes appears to demand a new nomenclature of iron compounds, for the following reasons : 1st. The term "steel," by which these soft products are commercially and professionally designated in England and in the United States, does not completely distinguish them from previously existing "steel" which would harden and temper. 2d. A nomenclature recognized in all languages seems desirable, as well for commercial as for scientific purposes, especially as lawsuits, already commenced, depend on the meaning of the term "steel." 3d. Although homogeneity, due to fusion, is usually recognized, and is by this committee recognized as the most definite characteristic of both bard and soft steel, this quality may be equally well expressed in other terms, thus leaving the old term, "steel," to define the malleable compounds of iron, which will harden and temper. Therefore, resolved, That this committee recommends the following nomenclature : 1. That all malleable compounds of iron with its ordinary ingredients, which are aggregated from pasty masses, or from piles, or from any forms of iron not in a fluid state, and which will not sensibly harden and temper, and which generally resemble what is called " wrought iron," shall be called WELD IRON (German, Sehweisseisen; French, fer soudé) 2. That such compounds, when they will from any cause harden and temper, and which resemble what is now called "puddled steel," shall be called WELD STEEL (German, Schweiss stahl; French, acier soudé).

Jan 1, 1877

By N. A. D. Parlee, M. M. A. El-Naggar, G. 8. Horsley

The apparatus was of a modified Sieverts type1&apos;2 with a reaction tube designed to function also as the cell component of an oxygen pressure gage. The reaction tube assembly is shown in Fig. 1 and described in Table I. The main body is a 1-in.-OD 15 mol pct calcia-stabilized zirconia tube. The ground-glass joint, g, the male part of which carried a prism for optical pyrometer use, was connected to the remainder of the Sieverts apparatus. The calibration of the cell (at its 1000°K operating temperature) for internal oxygen pressures (PO2in) in the range 0.2 to 10 9 atm was made against internal air pressures measured by mercury manometer and McLeod gage. At very low po2in values down to l<Tn atm the performance was checked by comparing pQ calculated from electromotive force measurement when the apparatus was filled with a) pure CO gas and b) a CO-CO2 mixture of the ratio CO-CO2 = 1:0.398, with Po, values calculated from the equilibrium constants of the following reactions at 1000°K:

Jan 1, 1968

By O. B. Bucklen, P. G. Meikle

INTRODUCTION The trend in the coal industry for many years has been to make every- thing "bigger and faster." This also held true for loading and storage facilities. Where once a million ton per year mine was rare, three to five million ton per year mines are not uncommon today in the bituminous industry. This greatly increased production, made possible through mechanization, required greatly improved loading facilities just to get the coal away from the mine. Also, there is a trend toward combining production from more than one mine and cleaning it in a single preparation plant. In addition to increased loading capacity, this frequently necessitates raw coal storage and blending facilities. The development of the unit train with its attendant economics, more than any other factor, has contributed to the widespread construction of storage and high-speed loading facilities. In the export market, the construction of ever larger coal colliers has contributed to a need for faster and larger loading facilities. In this climate of rapidly changing technology, any written account is faced with the possibility of obsolescence before its appearance. Thus, this chapter seeks to define the common and current practice in coal loading and storage facilities with the full knowledge that this practice is an ever-moving target. FUNDAMENTALS OF COAL STORAGE Storage of coal is becoming an increasingly important part of coal handling systems at mines, particularly since the advent of the unit train concept in transportation. In order to take advantage of reduced transportation rates on trainload shipments of coal offered by unit train movement, operators have found that storage is an economic necessity. In unit train practice large predetermined quantities must be loaded in relatively short periods of time as opposed to conventional practice where coal is loaded at a speed dependent on the production capacity of the mine and/or the cleaning capacity of the preparation plant. Two surveys of storage practices at mines reveal several objectives for storage.1, 2 Raw and/or clean coal storage is generally practiced in order to accomplish one, or a combination, of the following objectives: 1. To improve plant efficiency by distributing plant feed over the entire operating time, or to allow a preparation rate different from the production rate. 2. To limit interruptions of supply, ie, allow mine and plant to function independently with delays in one not affecting the operation of the other.

Jan 1, 1968

By C. E. McCarthy, A. George Stern, Stanley J. Green

The national interest prompts consideration of any new source of mineral wealth even though the immediate need may be of minor importance. A critical shortage of potash in the United States during the World War of 1914-18 stimulated broad development, which established an American potash industry on a basis so sound that this commodity is not even listed as urgent in the present war program. However, this should not minimize its importance, and the need remains, not only for adequate supplies of the usual potash salts (the chloride and the sulphate) but of all potash chemicals. Potassium carbonate (known commercially as pearl ash) has been a high-cost commodity; in consequence, the quantity used by industry has been relatively small. By a combination of fortuitous geographical circumstances, there is opportunity to produce a low-cost potassium carbonate with the possibility that this might become an important source of chemical potash. The following paper considers a recently developed process1 taking advantage of these conditions. Wyomingite Deposit For many years it has been known that a deposit of potash-bearing igneous rock known as wyomingite occurs in the south- western part of Wyoming at Zirkel Mesa, which is 44 miles northeast of the town of Green River (Fig. I). The western escarpment of this deposit is about 3 miles east of the Superior Branch of the Union Pacific Railroad. This mesa alone covers approximately 3300 acres, and the average thickness of the wyomingite flow is 75 ft. It has been estimated2 that about one billion tons of wyomingite occur in this one deposit, all of which can be mined by open quarrying without overburden. In addition, there are several smaller deposits within 10 miles, so that the aggregate wyomingite in the area approaches two billion tons. This is one of the world&apos;s largest sources of leucite, and the only known deposit of its kind in the United States. The wyomingite (which is in the form of a lava flow and numerous small craters), with the mineral leucite as its most important component, has a mineral composition3 of: leucite, 50 per cent; phlogopite, 15; diopside, 12; kataphorite, 15; glass and apatite, 8. The phlogopite is present in visible phenocrysts 1/8 to 1/2 in. in diameter, but the leucite usually is almost microcrystalline and not capable of liberation by grinding. Chemically, the Wyomingite has a potash Content averaging slightly higher than eleven per cent K2O. The potash is mainly in the leucite, but part of it is in the phlogopite and a small amount is in the feldspars that are occasionally seen as undigested occlusions of the granite country rock, through which the leucite-bearing lava intruded, and as sanidine feldspar both in the crystalline and glassy phases of the rock. A typical analysis of the wyomingite from Zirkel Mesa is as follows:

Jan 1, 1948

By A. George Stern, Stanley J. Green, C. E. McCarthy

The national interest prompts consideration of any new source of mineral wealth even though the immediate need may be of minor importance. A critical shortage of potash in the United States during the World War of 1914-18 stimulated broad development, which established an American potash industry on a basis so sound that this commodity is not even listed as urgent in the present war program. However, this should not minimize its importance, and the need remains, not only for adequate supplies of the usual potash salts (the chloride and the sulphate) but of all potash chemicals. Potassium carbonate (known commercially as pearl ash) has been a high-cost commodity; in consequence, the quantity used by industry has been relatively small. By a combination of fortuitous geographical circumstances, there is opportunity to produce a low-cost potassium carbonate with the possibility that this might become an important source of chemical potash. The following paper considers a recently developed process1 taking advantage of these conditions. Wyomingite Deposit For many years it has been known that a deposit of potash-bearing igneous rock known as wyomingite occurs in the south- western part of Wyoming at Zirkel Mesa, which is 44 miles northeast of the town of Green River (Fig. I). The western escarpment of this deposit is about 3 miles east of the Superior Branch of the Union Pacific Railroad. This mesa alone covers approximately 3300 acres, and the average thickness of the wyomingite flow is 75 ft. It has been estimated2 that about one billion tons of wyomingite occur in this one deposit, all of which can be mined by open quarrying without overburden. In addition, there are several smaller deposits within 10 miles, so that the aggregate wyomingite in the area approaches two billion tons. This is one of the world&apos;s largest sources of leucite, and the only known deposit of its kind in the United States. The wyomingite (which is in the form of a lava flow and numerous small craters), with the mineral leucite as its most important component, has a mineral composition3 of: leucite, 50 per cent; phlogopite, 15; diopside, 12; kataphorite, 15; glass and apatite, 8. The phlogopite is present in visible phenocrysts 1/8 to 1/2 in. in diameter, but the leucite usually is almost microcrystalline and not capable of liberation by grinding. Chemically, the Wyomingite has a potash Content averaging slightly higher than eleven per cent K2O. The potash is mainly in the leucite, but part of it is in the phlogopite and a small amount is in the feldspars that are occasionally seen as undigested occlusions of the granite country rock, through which the leucite-bearing lava intruded, and as sanidine feldspar both in the crystalline and glassy phases of the rock. A typical analysis of the wyomingite from Zirkel Mesa is as follows:

Jan 1, 1948

By C. E. McCarthy, A. George Stern, Stanley J. Green

THE national interest prompts consideration of any new source of mineral wealth even though the immediate need may be of minor importance. A critical shortage of potash in the United States during the World War of I9I4-I8 stimulated broad development, which established an American potash industry on a basis so sound that this commodity is not even listed as urgent in the present war program. However, this should not minimize its importance, and the need remains, not only for adequate supplies of the usual potash salts (the chloride and the sulphate) but of all potash chemicals. Potassium carbonate (known commercially as pearl ash) has been a high-cost commodity; in consequence, the quantity used by industry has been relatively small. By a combination of fortuitous geographical circumstances, there is opportunity to produce a low-cost potassium carbonate with the possibility that this might become an important source of chemical potash. The following paper considers a recently developed process1 taking advantage of these conditions. WYOMINGITE DEPOSIT For many years it has been known that a deposit of potash-bearing igneous rock known as wyomingite occurs in the southwestern part of Wyoming at Zirkel Mesa, which is 44 miles northeast of the town of Green River (Fig. I). The western escarpment of this deposit is about 3 miles east of the Superior Branch of the Union Pacific Railroad. This mesa alone covers approximately 3300 acres, and the average thickness of the wyomingite flow is 75 ft. It has been estimated2 that about one billion tons of wyomingite occur in this one deposit, all of which can be mined by open quarrying without overburden. In addition, there are several smaller deposits within 10 miles, so that the aggregate wyomingite in the area approaches two billion tons. This is one of the world&apos;s largest sources of leucite, and the only known deposit of its kind in the United States. The wyomingite (which is in the form of a lava flow and numerous small craters), with the mineral leucite as its most important component, has a mineral composition3 of: leucite, 50 per cent; phlogopite, 15; diopside, I2; kataphorite, 15; glass and apatite, 8. The phlogopite is present in visible phenocrysts 1/8 to 1/2 in. in diameter, but the leucite usually is almost microcrystalline and not capable of liberation by grinding. Chemically, the wyomingite has a potash content averaging slightly higher than eleven per cent K20. The potash is mainly in the leucite, but part of it is in the phlogopite and a small amount is in the feldspars that are occasionally seen as undigested occlusions of the granite country rock, through which the leucite-bearing lava intruded, and as sanidine feldspar both in the crystalline and glassy phases of the rock. A typical analysis of the wyomingite from Zirkel Mesa is as follows:

Jan 1, 1944

By Ralph H. Sweetser

BENEFICIATION of iron ores from the blast-furnace point of view means more than the usual enrichment of the iron contents by the removal of a large part of the clay, carbonic acid gas, silica, or moisture of the natural ore; it includes all these, but it also embraces several other mechanical .processes made , necessary by the exacting requirements of present-day blast-furnace practice. The increasing use of iron- bearing by-products, to as much as a third or more of the total ore burden, has introduced still another series of processes for improving the blast-furnace ore burden. As we look back over the past three decades of blast- furnace practice &apos;in. this country, we see that many of the blast-furnace troubles were directly due to lack of proper preparation of the iron ore burden,, and we realize that beneficiation in one form or another would have remedied the trouble. This was particularly true in the smelting of magnetic iron ores, where run-of- mine ore included such big lumps of &apos;magnetite along with rich fines that the furnace operations were greatly retarded and control of the furnace such as is usual today, was completely unknown.

Jan 1, 1930

By Ernest F. Burchard

Fluorspar is found in most of the states from the Rocky Mountains westward, and commercial production of the mineral has been reported from Arizona, Colorado, Nevada, New Mexico, Utah and Washington. The map in Fig. 1 indicates the general distribution of many of these deposits but it is by no means complete. In the summer of 1926 the writer examined certain deposits of fluorspar in Arizona, California, Colorado, New Mexico and Washington; in November, 1927, revisited the Jamestown, Colo., district, and in earlier years examined deposits in Colorado and New Mexico. Based on notes of his own and on descriptions and other data by H. A. Aurand, H. W. Davis, R. B. Ladoo, V. C. Heikes, W. D. Johnston, Jr., and by producers of fluorspar, he prepared the following brief descriptions of deposits and estimates of reserves of fluorspar, originally for the use of the subcommittee on fluorspar of the Joint Committee on Foreign and Domestic Mining Policy and on Industrial Preparedness respectively of the Mining and Metallurgical Society of America and the American Institute of Mining and Metallurgical Engineers. Descriptions of many fluorspar deposits in various western states and districts have been published. It is not feasible to summarize this literature here, but the appended bibliography will indicate to the interested reader what papers are available. Arizona Fluorspar has been reported as occurring in Arizona in the following localities: near Duncan, Greenlee County; near Naco, Tombstone, and Paradise, Cochise County; Black Mountain, Mojave County; 25 miles southwest of Tucson, and at Helvetia and Silver Bell, Pima County; near Mammoth mine, Pinal County; in Yavapai County, 7 miles from Aguila, and in the Bradshaw Mountains; and near Dome, Yuma County. Production has come principally from the Castle Dome district, Yuma County, with minor quantities from Greenlee, Pima and Yavapai counties. The writer examined deposits in the Castle Dome district, Yuma

Jan 1, 1934

By Frederick Becket

DOCTOR Albert Sauveur, distinguished scientist and Honorary Mem-ber of this Institute, predicted in the first Howe Memorial Lecture that the privilege of delivering this annual address would be considered a highly significant honor. The intervening years have well borne out Sauveur&apos;s prophecy. I wish to assure the American Institute of Mining and Metallurgical Engineers that I also deeply appreciate this honor, recognizing at the same time the present and even more the future respon-sibilities with which it is accompanied. Several of the previous lecturers had the good fortune to attend the classes of Professor Howe and to work in his laboratories. I was similarly favored, although in my instance and to my great regret the period was all too short. However, Howe&apos;s book, published in 1903, "Iron, Steel and Other Alloys," afforded me abundant opportunity to continue these studies. How well I remember the inspiration I derived from this famous book by Howe, the metallurgical master, pioneer, and educator! Remembering that Professor Howe contributed numerous papers to The Metallographist, a magazine supported from a technical point of view by the world&apos;s pioneers in metallography, I was curious a few days ago to learn the nature of Howe&apos;s early contributions to this magazine. The first paper by Howe in the first year of The Metallographist (1898) dealt with the allotropic theory; the second also treated of allotropy, and I quote the first sentence. of that paper: The allotropic theory of the hardening of steel may, like so many other important theories, have to be accepted or rejected not on direct proof or disproof, but on the accumulation of circumstantial evidence for or against it.

Jan 1, 1938