Search Documents

[America,-Dear, G. C. Anniston.-Klugh, B. G. Auburn. *Poor, R. S. Bankhead.-Armstrong, W. D. Bessemer.-Creveling, J. G. Lindstrom, W. A. McKenzie, W. C. Mitchell, F. R. Birmingham.-Abbott, C. E. Armstrong, G. R. Austin, W. W., Jr. Ball, T. L. Beard, A. H. Benjamin, F. S. Blackburn, E. C. Blair, A. J. Blair, C. S. Blair. H. W.]

Jan 1, 1946

By N. A. D. Parlee, M. M. A. El-Naggar, G. 8. Horsley

The apparatus was of a modified Sieverts type1&apos;2 with a reaction tube designed to function also as the cell component of an oxygen pressure gage. The reaction tube assembly is shown in Fig. 1 and described in Table I. The main body is a 1-in.-OD 15 mol pct calcia-stabilized zirconia tube. The ground-glass joint, g, the male part of which carried a prism for optical pyrometer use, was connected to the remainder of the Sieverts apparatus. The calibration of the cell (at its 1000°K operating temperature) for internal oxygen pressures (PO2in) in the range 0.2 to 10 9 atm was made against internal air pressures measured by mercury manometer and McLeod gage. At very low po2in values down to l<Tn atm the performance was checked by comparing pQ calculated from electromotive force measurement when the apparatus was filled with a) pure CO gas and b) a CO-CO2 mixture of the ratio CO-CO2 = 1:0.398, with Po, values calculated from the equilibrium constants of the following reactions at 1000°K:

Jan 1, 1968

By G. R. St. Pierre, M. J. Pool, R. Speiser

The activities of chromium in solid Cr-Ti solulions contaitning from 10 to 90 at, pct Cr were measured over the temperatutre range 1250" to 1380°C. The Knzudsen effusion technique with direct weighing of the Knudsen cell was used. This was possible because the vapor pressure 0f chromium is about 600 times greater than the capor pressure of titanium so that the amount 0f titanium effusing could be neg-Lected. the activities of titanium were determined by g-raphical integration of the Gibbs-Duhertz equatiotz. The solutio~ls sllcdied exhibited positive deviations from Raoult&apos;s law, but they approached ideality as the temperature was raised from 125 to 138t C. The integral free energy of mixing was calclated from the activity values. AF has a maximum value of - 1.66 kcal a1 1390°C and a composition oj 55 at. pcl Cv. The free energy of formation of &apos;TiCr, is —0.76&apos; lzcal a1 1250°C. The heats and entropies of mixing usere determined using the second law and thus tile mlues could be in error by a considerable amount. The Cv-Ti system is not a regular solution. ThE increasing emphasis on application of various models to alloy formation and solution behavior has led to an intensified interest in the thermochemistry of alloys. In a majority of the cases where different models have been applied the alloy system used was a simple one. However, the amount of data available on more complicated systems is small and in order to fully understand the behavior of metallic solutions more experimental work has to be carried out on these systems. The Cr-Ti system is reasonably complex and even though this system was being investigated as early as 1937 by Kroll,&apos; no previous work has been done on the thermodynamic properties of either the liquid or solid state. This research was undertaken to determine the thermodynamic properties of solid Cr-Ti alloys. EXPERIMENTAL PROCEDURE The experiments on the Cr-Ti system were carried out in a water-cooled metal vacuum system. This system is composed of a brass vaporization chamber wound with copper tubing for cooling purposes, a brass liquid-nitrogen trap, an oil diffusion pump, and a Duo-Seal forepump. The pressure in the system is measured with an ionization gage. The interior of the vaporization chamber is shown schematically in Fig. 1. The Knudsen cell is supported by the molybdenum tripod, and a magnetically operated shutter is provided to protect the Pyrex sighting glass against deposition of metallic vapors in the intervals between temperature measurements. Heating is accomplished by means of a 20-kw 450-kc Westinghouse oscillator. The susceptor in this case is 10-mil tantalum seamless tubing which also forms the outside of the sample container. The remainder of the sample container consists Of an im~ervims re-crystallized alumina crucible and a 10-mil-thick tantalum lid. Two holes are drilled in the lid. The diameters of these holes were measured with the calibrated stage of a "Tukon" microhardness tester. The thicknesses were measured with a micrometer. A Leeds and Northrup disappear ing-filament optical pyrometer was used to measure the temperature. This is sighted through the smaller of the two holes in the lid and corrections for the emissivity of the sample were not necessary since the ratio bf cell length to hole diameter was large enough to insure a hohlraum. The pyrometer was calibrated at the ~~t~~~l Bureau of Standards, and the correction for the Pyrex sighting window was determined in the laboratory. The titanium used in this investigation was obtained from Mallory-Sharon and the chromium from The Union Carbide Metals Co. The reported purities were

Jan 1, 1968

By G. H. Cady, L. C. McCabe, D. R. Mitchell

While running certain float-and-sink tests, unit coal calorific values were determined for gravity fractions of a series of Illinois coals from several districts in the southern part of the state. When these values were plotted against specific gravity what appear to be characteristic curves of somewhat different shape were obtained for each district represented. This in itself seems noteworthy. The shape of the curves seems to indicate that the lightest fraction of the coal, which inspection shows to be largely vitrain, suffers the least deterioration in storage. It was also observed that on dilution curves established with dry ash and B.t.u. values the fractions of 1.35, 1.40 and 1.50 sp. gr., which constitute the greater weight per cent of a given coal sample, fall more frequently on a straight dilution line than do the lighter or heavier fractions of the same sample. In most instances there is a marked steepening between the 1.35 and the fraction of lighter gravity. In general the curve increases in steepness between the fractions of 1.50 and 1.70 specific gravity. The variations in the unit coal-specific gravity curves as well as those observed in dilution curves which appear to be pertinent to this problem are: (I) variation in coal substance with change in specific gravity, (2) variation in kind and quantity of mineral matter with the specific gravity of the fraction, (3) factors of analytical procedure which tend to introduce error in analysis, particularly in high-ash and high-sulfur fractions. DISCUSSION (A. C. Callen presiding) E. Stansfield, ? Edmonton, A1ta.-—The necessity of avoiding oxidation in grinding and in drying should be emphasized. My assumptions as to pure coal coincide with t,he author&apos;s but most of my curves are nearly straight lines. The low sulfur content

Jan 1, 1934

By Samuel S. Wyer

Bethlehem Meeting, February, 1906 THE following abbreviations have been used in the text:¬ Am. MF. and Iron World. American Manufacturer and Iron World, Pittsburg, Pa. Can. Min. Rev. Canadian Mining Review, Ottawa, Can. Cass. Mag. Cassier&apos;s Magazine, New York, N. Y. Col. Eng. Colliery Engineer, London, Eng. Col. Guard. Colliery Guardian, London, Eng. Eng. and Min. Jour. Engineering and Mining Journal, New York, N. Y. Eng. News. Engineering News, New York, N. Y. Engr. Engineering, London, Eng. J. I. and S. I. Journal of the Iron and Steel Institute, Lon¬don, Eng. Jour. W Soc. of Engrs. Journal Western Society of Engineers, Chicago, Ill. Lond. Eng. The Engineer, London, Eng. Mines and Min. Mines and Minerals, Scranton, Pa. North of Eng. I. M. E. North of England Institute of Mining Engineers, Newcastle-on-Tyne, England. Oester Zeitsch f. Berg u. Hüt. Oesterrcichische Zeitschrift für Berg. und Hüttenwescn, Vienna, Austria. Pract. Engr. Practical Engineer, London, Eng. Proc. I. C. E. Proceedings Institution of Civil Engineers, London, Eng. Trans. A. I. M. E. Transactions American Institute of Mining Engineers, New York, N. Y. Trans. A. S. M. E. Transactions American Society Mechanical Engineers, New York, N Y Trans. Fed. I. M E. Transactions Federated Institute Mining Engineers, Newcastle-on-Tyne, England. Trans. I M E Transactions Institute Mining Engineers, Newcastle-on-Tyne, England.

Mar 1, 1906

Discussion of the paper of DORSET A. LYON and ROBERT M. KEENEY, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin. No. 92, August, 1914, pp. 1791 to 1800. LAWRENCE ADDICKS, Chrome, N. J.-I read this paper for the first time this afternoon, and it is really worthy of a much more careful reply than I can make with such a short time to consider it, but I just want to say that I differ with Dr. Lyon in his premises and conception of what happens in a refining furnace. He cites steel as an instance where the production of special grades justifies the high cost of power in an electric furnace, and goes on to say the same will be true in the case of copper, for the reason that you will get a better quality of product. I don&apos;t think you will get a higher grade of copper,. or a better conductivity, as I will explain in a moment. The cost of fuel in the Eastern plants is somewhere between 30c. and 40c. per ton of copper refined, and, if my memory serves me correctly, in an open-hearth steel furnace it is something like $1.25, so it is evident that steel could be handled to better advantage than copper on the basis of fuel. Now, taking the Great Falls plant to compare with is not quite fair, because that plant operates under peculiar conditions. The furnaces are relatively small; the coal is very bad and is very high in sulphur. No one would think of using a coal with 3.6 per cent. sulphur were anything better available. Due to these conditions, the amount of slag is inordinate, it being quoted as 3.5 per cent., and it is necessary to use lime, as there is a tendency to have troubles from arsenic owing to the very high current density used. I think he has taken about as hard a case as he could pick out. Now as to the conductivity of copper, my own idea about the reason that melted copper does not give as high a conductivity as pieces drawn directly from a cathode, or native copper, is that in the latter case the impurities are present as a mechanical mixture, while after melting they are chemically combined with the copper, which is a very different condition. Further, it is necessary to take the sample from a relatively smooth and consequently pure part of the cathode, as otherwise it would not draw. The same with the mass of copper; you pick out a good solid part of the copper, which is not representative. In fact, the refiners have all found they could not take fair samples of cathodes for a chemical analysis. It is always customary to use wire-bar copper -for the purpose of sampling, and the impurities are several times as great as shown by samples taken from .the cathodes. I think if we examine all of the examples he has given of cases where copper is higher in conductivity, it will fit with that explanation. For example, the Elmore process is a direct electrolytic deposit. Incidentally, at the present time there are a number of ex-

Jan 12, 1914

THE Institute assembled on Tuesday evening, October 24th, in the hall of the Franklin Institute, Mr. Frank Firmstone, VicePresident, in the chair. Mr. J. Price Wetherill, of Tremont, Pa., read a paper on An Outline of Anthracite Coal Mining in Schuylkill County, Pa. The paper was discussed by Messrs. Coxe, Rothwell, Heinrich, Harden, and Symons. The second session was held on Thursday evening. Mr. A. L. Holley, Chairman of the International Committee, appointed by the Institute to consider the nomenclature of iron and steel, offered the following report of the committee, signed by all the members: WHEREAS, The recent production of soft, cast, malleable compounds of iron by the Bessemer, the Siemens-Martin, and the crucible steel processes appears to demand a new nomenclature of iron compounds, for the following reasons: 1st. The term "steel," by which these soft products are commercially and professionally designated in England and in the United States, does not completely distinguish them from previously existing "steel which would harden and temper. 2d. A nomenclature recognized in all languages seems desirable, as well for commercial as for scientific purposes, especially as lawsuits, already commenced, depend on the meaning of the term " steel." 3d. Although homogeneity, due to fusion, is usually recognized, and is by this committee recognized as the most definite characteristic of both hard and soft steel, this quality may be equally well expressed in other terms, thus leaving the old term, " steel," to define the malleable compounds of iron, which will harden and temper. Therefore, resolved, That this committee recommends the following nomenclature : 1. That all malleable compounds of iron with its ordinary ingredients, which are aggregated from pasty masses, or from piles, or from any forms of iron not in a fluid state, and which will not sensibly harden and temper, and which generally resemble what is called " wrought iron," shall be called Weld Iron (German, Schweisseisen; French, fer soudé). 2. That such compounds, when they will from any cause harden and temper, and which resemble what is now called puddled steel," shall be called Weld Steel (German, Schweiss stahl; French, acier soudé).

THE Institute assembled on Tuesday evening, October 24th, in the hall of the Franklin Institute, Mr. Frank Firmstone, Vice-President, in the chair. Mr.. J. Price Wetherill, of Tremont, Pa., read a paper on An Outline of Anthracite Coal Mining in Schuylkill County, Pa. The paper was discussed by Messrs. Coxe, Rothwell, Heinrich, Harden, and Symons. The second session was held on Thursday evening. Mr. A. L. Holley, Chairman of the International Committee, appointed by the Institute to consider the nomenclature of iron and steel, offered the following report of the committee, signed by all the members: WHEREAS, The recent production of soft, cast, malleable compounds of iron by the Bessemer, the Siemens-Martin, and the crucible steel processes appears to demand a new nomenclature of iron compounds, for the following reasons : 1st. The term "steel," by which these soft products are commercially and professionally designated in England and in the United States, does not completely distinguish them from previously existing "steel" which would harden and temper. 2d. A nomenclature recognized in all languages seems desirable, as well for commercial as for scientific purposes, especially as lawsuits, already commenced, depend on the meaning of the term "steel." 3d. Although homogeneity, due to fusion, is usually recognized, and is by this committee recognized as the most definite characteristic of both bard and soft steel, this quality may be equally well expressed in other terms, thus leaving the old term, "steel," to define the malleable compounds of iron, which will harden and temper. Therefore, resolved, That this committee recommends the following nomenclature : 1. That all malleable compounds of iron with its ordinary ingredients, which are aggregated from pasty masses, or from piles, or from any forms of iron not in a fluid state, and which will not sensibly harden and temper, and which generally resemble what is called " wrought iron," shall be called WELD IRON (German, Sehweisseisen; French, fer soudé) 2. That such compounds, when they will from any cause harden and temper, and which resemble what is now called "puddled steel," shall be called WELD STEEL (German, Schweiss stahl; French, acier soudé).

Jan 1, 1877

By R. E. Radabaugh, J. M. Brown, J. S. Merchant

The Gilman district is on the northeast flank of the Sawatch Range in central Colorado. It has yielded a total of 10,000,000 tons of ore having a value of over $250,000,000. Paleozoic sediments intruded by a Tertiary quartz latite sill and unconformably overlying Precambrian intrusives and metasediments comprise the country rock of the area. The sediments strike northwesterly and dip 8° to 12° northeasterly. Structures in the Precambrian are related to the Homestake shear zone of the Colorado mineral belt. Only minor folding and faulting occur in the sediments. The principal ore bodies are massive sulfide replacement deposits in carbonate rocks. They consist of long, pipe-like mantos in the completely dolomitized Mississippian Leadville Limestone and funnel-shaped chimneys of copper- silver ore cutting across the Mississippian and Devonian strata. Mineralization is continuous from the chimneys into the mantos. The principal ore bodies are roughly in the shape of a four-tined fork which points up dip. Smaller manto deposits occur in the Cambrian Sawatch Quartzite, and fissure veins are present in the Precambrian rocks. The principal minerals in the mantos are marmatite and galena in a gangue of pyrite and manganosiderite. The chimneys consist of a central core of pyrite with erratically distributed chalcopyrite, tetrahedrite, freibergite, and occasional galena with a shell of zinc ore on the outer margin. Both the chimneys and the mantos are surrounded by imperfect shells of manganosiderite and sanded dolomite. The mineralization is of Laramide age. Hydrothermal alteration affects all rock units to varying degrees. Clay mineral alteration halos occur around the ore bodies. Hydrothermal solutions have developed sanded rock, rubble filled channels, and banded zebra textures, principally in the Leadville Limestone. Structural control of the ore bodies is not well defined. Both the location of the district and the chimneys are probably related to basement structures. The mantos are largely controlled by stratigraphic factors and a pre-Pennsylvanian karst topography in the Leadville Limestone, which were modified by hydrothermal activity, and by weak zones of northeasterly trending faults.

Jan 1, 1968

By L. C. Brown, A. J. Stewart

Phase transformations have been studied in Ag-Zn alloys quenched from the high-temperature bcc 0 phase and lying in the composition range 37.4 to 50.0 at. pct Zn. On quenching, the alloy with the lowest zinc content transformed to massive a (fcc); all other alloys formed the ordered (3&apos; phase. On deformation, a martensitic reaction took place forming a close-packed structure. At Lou&apos; zinc contents transformation to this structure was complete. However, above 43 at. pct Zn a p.rogressively increasing amount of ß&apos; was retained following deformation. The close-packed structure was fcc at lower zinc contents (under 47 at. pct Zn) and either hcp or a mixture of fcc and hcp at high zinc concentrations. The structures produced by cold working were unstable and on aging transformed to the ß&apos; phase or the complex hexagonal to phase. For low zinc contents (under 43 at. pct) the fcc st-ructure transformed directly to the equilibrium To phase. With higher zinc contents, some 13&apos; was retained following defownation, and on aging the amount of this phase relative to the close-packed structure increased. On further aging both structures transformed cornpletely to PO. Metallographic examination indicated that the nature of the deformation product depended very markedly on the mode of deformation. Tensile deformation gave a microstructure characteristic of thermal martensite. KING and Massalski1 have shown that an alloy of Ag-50 at. pct Zn quenched from the high-temperature bcc ß phase undergoes a low-temperature ordering reaction forming ß&apos; which can be retained to room temperature. On deformation an hcp phase is produced, although this is unstable and the structure reverts completely to ß&apos; on aging. In the present paper, the work of King and Massalski is extended to cover a wide composition range in the p phase, observations being made of the structure of the quenched 13 and of the effects of deformation and aging. The relevant portion of the Ag-Zn phase diagram is shown in Fig. 1. King and Massalski have shown that close to stoichiometry the ß&apos; phase is the equilibrium structure at low temperatures. The approximate composition range of this phase, taken from a recent paper by Pops and Massalski,3 is shown on the phase diagram. The locations of atom sites are very similar in the ß&apos; and to structures, and the 4, structure can be derived from the 0&apos; structure by a small movement of atoms mainly in the direction of the cube diagonal.4&apos;5 However, the probability of filling any particular atom site by a silver or a zinc atom is markedly different in the two structures. The structure can be considered partly ordered but the arrangement of the ordered atoms is completely different from that in the p&apos; structure and transformation from ß&apos; to requires a large fraction of the atoms to change position. It has been shown that the ß&apos; transformation is thermally activated involving normal nucleation and growth processes.5,8 Massalski and Barrett7 have shown that in the Cu-Zn binary the (3 phase can be retained in the ordered state to room temperature over a wide composition range. On deformation a new close-packed phase is produced, the structure varying from fcc to a mixture of fcc + hcp to hcp alone with increasing zinc concentration. It appears that an ordering reaction is necessary to retain the bcc phase to room temperature. In CU-Ga,8 the bcc phase cannot be retained to low temperatures as it transforms by a massive reaction above the ordering temperature of the ß phase. The structure of the massive phase is very similar to that in Cu-Zn, varying from fcc to fcc + hcp to hcp with increasing zinc concentration. Similar structures have also been observed in CU-A1,9 Ag-Cd,10,11 and Ag-Al.12 EXPERIMENTAL The alloys were prepared by melting fine silver (99.99 pct purity) and electrolytic zinc (99.999 pct

Jan 1, 1969

By B. J. Kochanowsky

TO improve blasting methods it is necessary to know how the explosive force acts and how rock resists this force. Because of the tremendous power developed within milliseconds and the great number of other factors directly affecting the technical and economic results, an analysis of the fundamentals of blasting theory is difficult. But since the rules used for layout design and for calculations of size of explosive charges are based on theoretical assumptions, complete knowledge of blasting theory has great practical importance in mining. Analysis of Blasting Theory: It is interesting to note the opinion of blasting experts with respect to contemporary blasting theories. F. Stussi; Professor of the University of Zurich, stated: "We do not have enough experience yet to change our army engineering regulations in blasting and base it on new fundamentals. It is our duty to collect more practical data and to do more research in blasting to close this gap." K. H. Fraenkel,2 editor of the Manual on Rock Blasting published in 1953 in Sweden and written by well-known Swedish, German, Swiss, and French blasting and explosive experts, said: "To the best of our knowledge no suitable formulas for civil blasting work are to be found in the American, French or German literature." Present blasting theory is based upon two assumptions. 1) The blasting force of explosive acts in concentrical and spherical form. 2) Rock resistance against the explosive force is directly proportional to the strength characteristics of the rock. The first classical formula based on theoretical fundamental in blasting theory for explosive charge calculation was introduced by Vauban, a military engineer who lived 300 years ago. It was Vauban who proposed the famous formula L = w3 q, where L is the explosive charge, w = line of least resistance, and q = specific explosive consumption proportional to the weight of rock. Later engineers used q as proportional to the strength of the rock. Since Vauban&apos;s time different suggestions concerning blasting theory have been proposed. However, the principles stated at that time so affected the thinking of later generations that his formula is still in use and practically unchanged. The first controversy concerned the form of crater. It was found that geological features of rock affected its form. The factor q was analyzed thoroughly by Lares3 and later by Ohnesorge," Weichelt,5 Bendel,6 and others, but the assumption remained that resistance against explosive force is directly proportional to the strength of the rock blasted. The greatest controversy, which has not yet been settled, concerned w. It was noted that w3 is more appropriate for long lines of resistance and w2 for lines of resistance less than 15 ft. Based on the assumption that the explosive force acts concentrically and spherically, spacings between charges were limited to distances not greater than the length of line of least resistance. Sometimes larger spacing is recommended, but this is due to the advantageous geological and physical properties of rock and not to the action of an explosive force as such. In addition to the classical formula, empirical formulas are used widely. These state that the explosive charge is directly proportional to the volume of blasted rock in cubic yards, and the amounts of explosive required are usually expressed in pounds of explosive per cubic yard of rock. Empirical and classical formulas are contradictory. In the empirical formula, but not in the classical formula, explosive charge is taken proportional to all three space axes: line of least resistance, spacing, and bench height. In spite of this contradiction, both formulas give good results. This is possible because as now practiced the explosive charge calculation for heavy burdens need not be highly accurate. Each, open pit or quarry, usually works with a certain relation between bench height and line of least resistance and between charge spacing and line of least resistance. When these relations are changed, however, the specific explosive consumption q changes greatly. This is one of the reasons why the principles on which the formulas are based appear to be incorrect. In addition to the formulas discussed, others exist and are based more or less on the same theoretical

Jan 1, 1956

By W. O. Philbrook, K. Natesan

A mathematical model was derived for the temperature change in a particle undergoing heterogeneous chemical reaction and heal exchange with a stream of fluid. The model has been applied specifically to the exothermic oxidation of spherical particles of zinc sulfide. Very good agreement was obtained between the theoretical prediclion and experimental observation. It was found that at no stage of the reaction was the particle subjected to a state of thermal instability. In studies of gas-solid reactions, it is generally assumed that the gaseous and the solid phases are at the same temperature throughout the reaction period. This is not strictly true since most of the reactions are either exothermic or endothermic in nature. This paper deals only with heterogeneous gas-solid reactions of noncatalytic type. In the case of exothermic reactions (e.g., roasting of sulfides), there may result an increase in temperature of the particle due to the release of the heat of reaction, and this increase in temperature may enhance the reaction rate and thus cause further release of heat. Such a "spiralling" effect may lead to a thermally unstable situation within the particle. On the other hand, in the case of endothermic reactions (e.g., calcination of limestone), there may occur a decrease in temperature of the particle as the reaction proceeds, leading to a virtual "quenching" of the reaction front. A general discussion of autothermic processes with emphasis on properties and reactor design is given by Van Heerden. 1 Levesque and cubicciotti 2 observed self heating of the sample in the oxidation of thorium. Anous et al. 3 observed self cooling of the sample in their dehydration studies on chrome alum. Cannon and Denbigh, 4 and Ong et al.5 reported self heating of the sample in their studies of the kinetics of oxidation of zinc sulfide. A typical plot of heat generation and heat loss rates with reaction temperature is shown in Fig. 1.&apos;14 The Sigmoid curve represents the heat generation rate while the straight lines represent the heat loss rate. The main objectives of this analysis are to estimate the temperature increase of a single particle undergoing an exothermic reaction and to study the possibility of a thermally unstable situation within the particle. Also, a study of the dependence of the tempera- ture increase on different process variables has been attempted. A "she ll-by-shell" method has been proposed to analyze the problem. The shells may be made as small as necessary, and equations may be set up for heat transfer by various mechanisms. Such equations will have to be solved for each shell, with the boundary conditions for ith shell being obtained from the (i - 1)th shell, using a high speed digital computer. The oxidation of spherical particles of zinc sulfide is considered for this analysis, but the treatment is general enough to be applicable to other reactions and particle shapes. The oxidation reaction can be written as AH =« -115 kcal/mole ZnS [1] Such a reaction has been found to proceed in a topo-chemical manner; i.e., as the reaction proceeds, a progressively thicker outer shell of zinc oxide is formed, while the inner core of unreacted sulfide decreases. It has been found experimentally, both in the present work and in the previous investigations,4-6 that the particle retains its original dimensions. Therefore, at any given time, the particle may be

Jan 1, 1970

One of the best known of the early mining districts of Nevada was that at Eureka, where gold was first produced in 1864. While the most productive period for the district was during the early 1900s, production was maintained until World War II. During this time it is said that the Eureka district produced as much as $200 million from over 3,200 km (2,000 miles) of tunnels and workings. The Windfall Mine was discovered in 1902; and a 100 ton cyanide plant was operated there during the periods 1907 to 1912 and 1932 to 1940. Since 1974, however, Windfall Venture has been operating a unique heap leaching facility on the site of the old Windfall Mine. Gold at the Windfall occurs primarily in the Cambrian Hamburg dolomite which has been "sanded" and in which the original cementing material has been destroyed. The gold is micron sized and is accompanied by anomalous amounts of arsenic and mercury; however, the ore is low in base metals which distinguishes it from the typical Eureka district ores. Mining the ore causes it to break down into very fine sizes, approximately 50% minus 150 microns (100 mesh). Conventional heap leaching by spraying proved to be impossible; and extensive test work on alternate methods, aided by the United States Bureau of Mines, was conducted using 9 m (30 ft) high columns and then large tonnage heaps. The leaching procedure adopted was to build 10.6 m (35 ft) high heaps on a 50 mm (2 in.) asphalt pad covered with a layer of gravel for drainage assisted by perforated pipe drains and gravel-packed sumps. A berm is constructed around the top of each pad and cyanide solution is allowed to “pond” on top of the heap. The resulting percolation is at the rate of 24 liters per sq m per hr (0.6 gal per sq ft per hr), a figure about 2.4 times the average used in other heap leaching operations. The dolomite furnishes its own protective alkalinity and no lime or caustic is used in the solution which contains 0.4 kg per mt (0.8 lb per st) of NaCN. Pregnant solution from the heaps averages about 0.7 g Au per mt (0.02 oz per st) with a cyanide content of about 0. 2 kg per mt (0.4 lb per st) and a pH of plus 9. Addition of NaCN brings the pH of the leach solution up to 11 to 12. Carbon adsorption of the gold was originally done in six enclosed columns mounted in a trailer but five conventional columns have been substituted as the size of the operations has increased. Carbon stripping is with hot caustic, cyanide and 10% ethanol solution. The

Jan 1, 1981

By Rollin Farmin

"SWELLING GROUND" delivers pressure on mine timbers that originates in expansion of the wall rock, whereas "heavy ground" delivers only gravitative pressure. Of the several possible causes considered, the swelling is attributed to the physical surface action of water on gouge and flaky rocks at the periphery of the mine opening.

Jan 1, 1944

By M. Yoshinuga, S. Watanabe

Some iron ores, sinters and pellets occasionally show abnormal behavior during reduction which makes them undesirable as blast furnace burden. These may be divided into the following three types: (1) decrepitation of iron ore, (2) swelling of iron ore and pellet, (3) size degradation of sinter. In this paper reduction experiments and microscopic examinations were made to clarify the mechanisms and causes of these abnormal phenomena. Decrepitation occurs mainly when compact hematite ores containing small amounts of limonite are heated to about 500°C. Abnormal swelling of ores and pellets is caused by the rapid growth of fibrous metallic iron from the surface of wustite grains during rapid reduction and is fundamentally related to their original microstructure. Size degradation of sinter occurs through the development of cracks in the reduction stage from hematite to magnetite. About 80% of the iron ore used in Japan&apos;s blast furnaces comes from abroad, and the iron and steel industry must import this raw material from distant overseas places at high freight rates. The blast furnace operators, therefore, have made strong efforts to cut costs under these restrictive raw materials conditions by increasing productivity and simultaneously decreasing coke consumption. If, however, a high proportion of the ore burden consists of unsuitable materials furnace irregularities often result, establishing the need for detailed investigations of the basic natures of the ore constituents and their reactions during the reduction process. Recent investigations &apos;-&apos; of various ore burdens suggest that some iron ores, sinters and pellets are occasionally abnormal in appearance and behavior during reduction studies and may prove to be undesirable for use in the blast furnace. In the present study reduction experiments and microscopic observations were made to clarify the causes and the mechanisms of the abnormal behavior observed in some constituents of the burden and their effect on blast furnace performance. REDUCING APPARATUS The four kinds of reducing apparatus used in this investigation were the following: 1. The JIS* (Modified Gakushin&apos;) apparatus shown in Fig. la is most commonly used in Japan to evaluate the reducibility of ores under static conditions. It consists of a stainless steel tube of 60 mm inside diam suspended from a balance. 2. Linder&apos;s Reduction Test apparatus (Fig. lc) has a reducing barrel 130 mm diam and 200 mm long which rotates at 30 rpm. Some modifications were made in test procedures. 3. Gakushin Standard Test apparatus for determining the reducibility of granular ores (Fig. Id) consists of a horizontal silica tube 32 mm diam, 370 mm long and a movable electric furnace which enables rapid heating and cooling of the specimens. 4. The test apparatus for reduction under load (Fig. lb) gives a comprehensive evaluation of the behavior of ores under conditions simulating the static loading and the chemical reduction conditions encountered in. a blast furnace stack. A stainless steel tube of 50 mm diam and a carbon rod of 35 mm diam were used as the sample container and the support for the weight, respectively. In each investigation care was taken to select the most suitable method and apparatus to distinguish the abnormal nature of the ore in question. SIZE DEGRADATION OF SINTER DURING REDUCTION Sinter makes up the major portion of the blast furnace burden and its behavior during reduction should bear a close relationship to the iron productivity. Recently, some of the sinter was found to show serious size degradation during reduction at a relatively low temperature range. Because this phenomenon was thought to be a possible source of furnace irregularities, tests were made to clarify the phenom-

Jan 1, 1969

By Frederick Becket

DOCTOR Albert Sauveur, distinguished scientist and Honorary Mem-ber of this Institute, predicted in the first Howe Memorial Lecture that the privilege of delivering this annual address would be considered a highly significant honor. The intervening years have well borne out Sauveur&apos;s prophecy. I wish to assure the American Institute of Mining and Metallurgical Engineers that I also deeply appreciate this honor, recognizing at the same time the present and even more the future respon-sibilities with which it is accompanied. Several of the previous lecturers had the good fortune to attend the classes of Professor Howe and to work in his laboratories. I was similarly favored, although in my instance and to my great regret the period was all too short. However, Howe&apos;s book, published in 1903, "Iron, Steel and Other Alloys," afforded me abundant opportunity to continue these studies. How well I remember the inspiration I derived from this famous book by Howe, the metallurgical master, pioneer, and educator! Remembering that Professor Howe contributed numerous papers to The Metallographist, a magazine supported from a technical point of view by the world&apos;s pioneers in metallography, I was curious a few days ago to learn the nature of Howe&apos;s early contributions to this magazine. The first paper by Howe in the first year of The Metallographist (1898) dealt with the allotropic theory; the second also treated of allotropy, and I quote the first sentence. of that paper: The allotropic theory of the hardening of steel may, like so many other important theories, have to be accepted or rejected not on direct proof or disproof, but on the accumulation of circumstantial evidence for or against it.

Jan 1, 1938

By K. G. Davis, P. Fryzuk

A study has been made of the effect of undercooling on the grain structure and solute distribution in small ingots of pure bismuth and of a 100 ppm Ag in bismuth alloy. Autoradiographic evidence shows that in undercooled melts a network of dendrites is formed throughout the melt immediately after nu-cleation. At large undercoolings the dendrites are very thin and closely spaced. The origin of the observed grain morphology can be explained on the basis of information about the mode of solidification revealed by the impurity substructure. WHILE a great number of studies of nucleation in undercooled molten metals have been made, comparatively little attention has been given to the mode of solidification from melts with large undercool- ings. Colligan and Bayles1 and Walker2 have measured the rate of advance of the solid-liquid interface in undercooled nickel melts, but the morphology of the solidifying material remained a matter of speculation. Fehling and Scheil3 have described the grain structure in ingots formed from undercooled melts of nickel, palladium, and copper, and a series of Ni-Cu and Ni-Pd alloys. At small undercoolings, equiaxed structures are observed, the grain diameter tending to increase as the temperature of nucleation is lowered. At greater undercoolings, a columnar structure is developed, while with still further undercooling there is a smaller grain size incorporating rather coarse subgrains. All-bright and Colligan4 examined the grain structure shown by ingots solidified from melts of nickel and of Ni-Ag alloy at an undercooling of 105°C, and concluded that considerable grain growth had taken place after solidification. The object of the present work is to correlate the mode of solidification from undercooled melts with both the grain structure and impurity segregation, using tracers to examine the latter.

Jan 1, 1965

By J. H. Frye, R. M. Treco

One of the chief hindrances to an understanding of the hardness of solid solutions is the sparsity of suitable hardness data. There is great need of a large body of hardness data obtained from many different alloys of high purity by identical testing methods and corrected to correspond to a single grain size. A considerable amount of such data has been obtained by means of the Meyer analysis on copper-rich and silver-rich solid solutions. There are enough of these data to permit comparison of numerous alloys at equal solute concentration in these two solvents, but only in a few cases is it possible to construct hardness-concentration curves for any given alloy. Therefore additional hardness work on most of these alloys is desirable. The primary solid solutions of silver with cadmium, indium, tin, or antimony as solute are of special interest, since all elements are from the same period of the periodic table and since, as shown previously,l the hardening effect of equal percentages of these solutes is proportional to the lattice expansion produced by them. This paper presents the relation between hardness and concentration in the silver-antimony system from very dilute to nearly saturated solutions of antimony in silver. Experimental Procedure Alloys were made from silver, 99.99 per cent pure, and antimony, 99.975 per cent pure. Silver and antimony were placed in graphite crucibles that had an ash content of less than 0.7 5 per cent. These metals were melted and allowed to solidify in a vacuum, which, after melting was corn- . plete, was usually equivalent to 3 mm. of mercury. A high-frequency furnace was used. The ingots so obtained were worked and annealed to lessen segregation and to control grain size. Annealing was done in evacuated and sealed glass tubes. Hardness measuremeuts on specimens from these ingots were by means of the Meyer analysis.394 Using a 4-mm. ball, impressions were made under seven loads from 25 to 400 kg. The diameter of impression made under each load was measured. This enabled calculation of the constants in the well-known formula of Meyer. L = adn where L = load, d = diameter of impression, a = a constant, n = a constant The Meyer hardness is defined as P = L/i(1/4pd2) or P = 4adn-2/p Meyer hardnesses corresponding to d = I and to d = 4 are of especial interest, since the first corresponds to comparatively slight &apos;plastic deformation and the second to the maximum plastic deformation producible by penetration of the ball. These

Jan 1, 1945

By Robert J. De Angelis, James H. Barker

An improved method for solving dynawzical dislocation problems using a digital computer is described in this paper. Interactions between two distinct types of dislocations were studied: attractive screw dislocations; and Lomer lock forming dislocations. One dislocation is positioned in the lattice and is initially at rest, while the other dislocation is moved through the lattice on an intersecting slip plane at a constant velocity in the range 0.5 to 0.999C. (C is the transverse velocity of sound.) The results obtained from these computations indicate that screw dislocations account for a small fraction of the total strain over a wide portion of the range of velocities studied. They further indicate that mixed dislocations mainly repel other dislocations in the neighborhood of the active glide plane. From this a possible explanation for cell formation is put forth. The density of Lomer locks expected to exist after a strain of 0.2 was found to be 1.4 x 106 cm-2 which is in good agreement with indirect experimental estimates. IN the past, predictions of favorable or nonfavorable dislocation reactions were based on the associated changes in elastic strain energy. Such considerations take no account of the probability of the two dislocations coming into contact to react. Venables1 was the first to approach these probabilities by considering the interactions between two moving screw dislocations on perpendicular glide planes. Because of the restrictive types of dislocations and glide plane geometry employed, his results have limited application to metallic crystals. The work to be presented here develops a general approach to solving dynamical dislocation problems; either dislocation-dislocation interactions, presented here in detail, or dislocation interactions with any other suitably defined stress field. Two types of dislocation-dislocation interactions common to face centered cubic (fee) materials are considered: those between pure screw dislocations of opposite sign on intersecting slip planes and those between mixed dislocations on intersecting slip planes, that can react to form a perfect dislocation. This latter reaction, referred to as the Lomer reaction, produces a locked product dislocation that finds it energitical favorable to disassociate into two Shockley partials and a stair-rod dislocation. This partial configuration known as a Lomer-Cottrell (L-C) lock plays a major role in work hardening of fee crystals. seeger2 names the L-C lock as the prime contributor to Stage II hardening while Kuhlmann-wilsdorf3 and Meakin and Wils- dorf4 also state that it is a significant contributor to work hardening. However, with a few notable exceptions,5-7 direct observations of the Lomer lock and the L-C lock by electron transmission microscopy are scanty, and even these are subject to other interpretations.5,6 In a study of partial dislocations present in austenitic stainless steel, whelan8 did not observe any L-C locks at the head of pile-up groups. This result contradicted existing work hardening theories and led him to postulate an alternate theory based on the stress required to break away dislocations intersecting a pile-up group, from their stacking fault nodes. Due to the importance of the Lomer reaction in producing L-C locks which are an essential feature in current work hardening theories and because there exist no data giving direct quantitative values for the density of locks, and because there has even been some doubt expressed as to whether this important reaction occurs at all, a study of the dynamic behavior of the mixed dislocations which form the Lomer lock was undertaken. Due to their ability to cross-slip with relative ease, screw dislocations play an important role in the deformation of fee crystals. For this reason, the second type of reaction considered here is between screw dislocations of opposite sign. In addition, computations in volving screw dislocation interactions are relatively simple, thus providing a convenient check on the cornputational scheme employed. DEFINITION OF PROBLEM The force exerted on a dislocation due to a generalized stress field is given by the Peach and Koehler9 equation: Here t2 and b2 are respectively the tangent and Burgers vectors of the dislocation, and T1 is the stress dyadic defining the local stress field. The stress field may be externally applied or generated internally by the presence of a lattice defect, such as a second dislocation, as is the case in this work. Frank10 has shown that an equivalent momentum, P, of a screw dislocation can be defined by: Here, EST is the total energy of a screw dislocation and ESo is its rest energy. The left side of Eq. [2] is the time derivative of momentum and the right side is the position derivative of the energy due to the dynamical nature of the dislocation. The total energy of a dislocation is the sum of the potential and kinetic energies. Weertman11 has developed the expressions which were used here; these give the potential and kinetic energies of uniformly moving edge and screw dislocations in an isotropic medium.

Jan 1, 1969

By Ernest F. Burchard

Fluorspar is found in most of the states from the Rocky Mountains westward, and commercial production of the mineral has been reported from Arizona, Colorado, Nevada, New Mexico, Utah and Washington. The map in Fig. 1 indicates the general distribution of many of these deposits but it is by no means complete. In the summer of 1926 the writer examined certain deposits of fluorspar in Arizona, California, Colorado, New Mexico and Washington; in November, 1927, revisited the Jamestown, Colo., district, and in earlier years examined deposits in Colorado and New Mexico. Based on notes of his own and on descriptions and other data by H. A. Aurand, H. W. Davis, R. B. Ladoo, V. C. Heikes, W. D. Johnston, Jr., and by producers of fluorspar, he prepared the following brief descriptions of deposits and estimates of reserves of fluorspar, originally for the use of the subcommittee on fluorspar of the Joint Committee on Foreign and Domestic Mining Policy and on Industrial Preparedness respectively of the Mining and Metallurgical Society of America and the American Institute of Mining and Metallurgical Engineers. Descriptions of many fluorspar deposits in various western states and districts have been published. It is not feasible to summarize this literature here, but the appended bibliography will indicate to the interested reader what papers are available. Arizona Fluorspar has been reported as occurring in Arizona in the following localities: near Duncan, Greenlee County; near Naco, Tombstone, and Paradise, Cochise County; Black Mountain, Mojave County; 25 miles southwest of Tucson, and at Helvetia and Silver Bell, Pima County; near Mammoth mine, Pinal County; in Yavapai County, 7 miles from Aguila, and in the Bradshaw Mountains; and near Dome, Yuma County. Production has come principally from the Castle Dome district, Yuma County, with minor quantities from Greenlee, Pima and Yavapai counties. The writer examined deposits in the Castle Dome district, Yuma

Jan 1, 1934