Search Documents

By Sixten Wollmar

A RESUME. of some important points regarding the life of drill steel, which have so far been learned from investigations carried out in the SKF Hofors' mines, Sweden, by L. Nordenfelt, is given below. By examining all fatigue breakages which occurred in the test it has bees conclusively proved that when a rock drill of the self-rotating type is used all break-ages of this kind start from the surface of the hole in the steel. It has further been proved that the rough hole surfaces (i.e., the marks left by the indentations of the sand core), are the starting points for the fatigue cracks and that the corrosive action of the water has .a very detrimental influence on the life of the steel. It is now a well known fact that this corrosive action concentrates at the bottom of the indentations left by the sand. The corrosive action of water has been well described by U. R. Evans in his paper, "Some Recent Work on the Corrosion of Metals," delivered on March 31, 1926, before the Liverpool Engineering Society, which is quoted in part below: "It is well known that, under ordinary conditions, most metals do not corrode in water unless dissolved oxygen is present. The strange feature of corrosion in submerged metals, however, is that the attack does not proceed mainly over those portions of the surface which could be reached readily by oxygen; deterioration takes place at certain points which are relatively, inaccessible to oxygen. When. a metal becomes pitted by corrosion, further attack usually deepens the pits, and in many cases it could be proved that there was no free oxygen at the bottom of the pits. None of the older theories of corrosion explain the fact that, although oxygen is necessary for rapid corrosion to take place, the attack actually occurs at the very points which could not be reached directly by oxygen.

Jan 6, 1928

By F. E. ROGERS

CUSHMAN TUNNEL No. 2 is adjacent to the Hood Canal, near potlatch, Wash. It is 17 ft. inside .diameter, about 13,000 ft., or two and one- half, miles in length, and is a part of the second unit of the Cushman power project. It connects Cushman ' Dam No. 2 and the penstocks that lead to the power house on the beach about 400 ft. vertically below the outlet of the tunnel. One shaft, 190 ft. deep, and two adits between 300 and 400 ft. long, were provided to speed up driving operations. his arrangement gave 6 working headings, which were operated 24 hr. daily. The shaft provided a manway, cageway, and skipway.

Jan 1, 1931

By W. J. McGee

Most nations and states have conducted geological surveys, generally with the view of discovering and developing natural resources, sometimes with the aim of promoting science. In some cases, as in the first survey of Pennsylvania, the official geologist so far preceded the prospector and miner as to guide the discovery and exploitation of the commoner ores, mineral fuels and structural materials; but in most instances statesmen have only been awakened to the need of such a survey by the successful extraction of minerals;

Jan 1, 1893

By E. B. Mayo

David LeCount Evans (Consulting Petroleum and Mining Geologist, Wichita, Kans.)-—Not only E. B. Mayo but also W. C. Lacy, who apparently urged the preparation of this analysis, is to be commended. Regional thinking of this type is needed to assure future success in the never-ending search for new mineralized and petroliferous districts. As is usually the case, here is a regional study that will be read by the mining geologist alone. It is ironic that several of the trends established in this study have suggested themselves in northern mid-continent, detailed, and regional studies. These, where established, have offered new keys to petroleum exploration and have provided a possible basis for unraveling a number of broad generalities. The oil geologists, active in Colorado, Kansas, and Oklahoma, would find much food for thought in Mr. Mayo's projections. To be more specific: 1) The parallelism between E. B. Mayo's Texas Lineament and the Amarillo Uplift, the Wichita Complex and the Arbuckle Complex of the Texas Panhandle and Southern Oklahoma is viewed with interest and appears especially significant when compared with the similar northwest trend of the Central Kansas Uplift, a major trend of production. 2) Considering the various northeast zones of Fig. 2, and with particular reference to Mayo's C-C, the Jemez Zone is on direct line with one of several northeast-southwest controls which the present writer has been using with some success in Kansas subsurface correlations. Considering zones of shearing, with no apparent vertical displacement, but suggesting strike-slip movement, because of the staggered effect on other features which cross such trends, Mayo's philosophy presents regional possibilities for lines of weakness, considered to this time of only local significance. 3) And, finally, in an area as distant from the Southwest as central Kansas, the north-south trends of the Fiarport-Ruggles anticline, the Voshel-Hol-low Nikkel-Burrton structures, the Dayton to Stut-gart trend, the north, slightly east trend of the Ne-maha structural complex, and others all seem to approach the north-south alignments, a through f, of Mayo's Fig. 3. Mayo's employment of structural intersections to pinpoint crustal weakness, to localize igneous activity and its accompanying mineralization is not, perhaps, a new concept, but it is a 1958 model, produced by tools improved from the ever-increasing accumulation of geological observations. The use of intersecting trends in petroleum geology is not a new idea, since much production in earlier days was encountered via the straight line projections of established trends to centers of intersection. A tragedy in this age of specialization is that iron curtains have been raised between groups, all seeking raw materials, all acolytes at the altar of structural geology, but all smugly content in and protected by the ivory towers of petroleum geology, engineering geology, mining geology, and geophysics. Mayo presents basic ideas which can stimulate mid-continent structural thinking and, in the case of cen- tral Kansas. he provides a key to replace the broad and overworked simple monoclinal, sinkhole-dotted, Karst topography credo, which is not finding its share of new oil in a state where the declining discovery ratio is disconcerting. The American Association of Petroleum Geologists would do well to add E. B. Mayo to its list of Distinguished Lecturers. Evans B. Mayo (author's reply)—In reply to David LeCount Evans' comments, it is pleasing to learn that some of the elements discussed in my paper may interest petroleum geologists as well as mining geologists. This should not be surprising, however, because the lineaments make up the framework of the continent, and the oil-bearing sediments must reflect to varying degrees adjustments of basement blocks along their boundaries. A further possibility that petroleum geologists must have considered is that the slow escape of heat from buried lineaments and their intersections has aided the separation of oil from the sediments and started the migration into traps. Regarding the specific points listed by Evans, the following are suggested: 1) The branch of Texas Lineament marked 1' (Fig. 3) is thought to extend eastward through the Capitan Mts., New Mexico, through the long Tertiary dikes east of Roswell, and beyond via the Matador and Electra ranges of the Red River Uplift, Texas. Its further continuation might be the eastern flank of the Ouachita Fold Belt. The Amarillo-Wichita-Arbuckle zone of uplifts appears to continue east-southeastward the Spanish Peaks belt (3-5, Fig. 3). The northwest-trending Central Kansas Uplift would not belong to the above set, except insofar as the Central Kansas Uplift is traversed by west-northwest folds, possible continuations of the Uinta belt (5-5, Fig. 3). 2) The possible continuations into Kansas of the Jemez zone are new to me and are most welcome suggestions. 3) Most of the nearly north-south Kansan structures mentioned by Evans are unfamiliar to me, but the Nemaha Uplift itself appears to be part of a very pronounced structure traceable from the Cerralvo Fault Zone, south of the Rio Grande, through the Bend Arch, Texas, and the Nemaha Uplift, into the Pre-Cambrian of Minnesota (?). This nearly meridional zone is crossed and broken by the Rio Grande Embayment and by the Red River-Wichita Syntaxis. Petroleum geologists realize the economic importance of these features. Perhaps it is inevitable that some papers of general interest be buried in the journals of specialized groups. Moreover, papers dealing with regional, or lineament, tectonics and its applications to exploration for economic mineral deposits are as yet few in the American literature. The opportunity to advance this field is open to all those who are not ultra-conservative and who have a lively curiosity, plenty of patience, and not too many business restrictions. In conclusion, much appreciation is extended to D. L. Evans for his comments.

Jan 1, 1960

By Robert M. Keeney

Important recent developments in the melting and annealing of non-ferrous metals include: 1. Melting of nickel silver in the vertical ring induction furnace. 2. Electric melting of stereotype metal. 3. The rotary-drum gas-fired brass melting furnace. 4. The low-frequency coreless induction furnace. 5. Finishing annealing of brass sheets with city gas1 replacing wood in the large brass-rolling mill. 6. Electric annealing of brass and copper tubing and sheets. 7. Replacement of oil by gas and electricity in the annealing of nickel-silver shells and stampings. Melting Nickel Silver in Vertical Ring Induction Furnace Although over 90 per cent. of the output of the brass rolling mills in the United States is now melted in electric furnaces,2 until recently a considerable part of the output of nickel silver has been the product of the pit fire. The application of the electric furnace to the melting of nickel silver has been slow for several reasons: (I) Until recently no lining has been available that gave a satisfactory life in the vertical ring induction furnace when melting nickel silver; (2) the rocking arc furnace so widely used in the foundry does not appear to have been favored by the rolling mill for melting nickel silver, possibly because the gases present may affect the quality of the alloy; and (3) the exclusive rights to the use of the high-frequency coreless induction furnace (which has proved very satisfactory for melting nickel silver) for the wrought brass industry are controlled by one concern. A little over one year ago the first vertical ring induction furnace to be used for melting nickel silver in the Naugatuck Valley was placed in operation. This was followed by two more in the same mill, and by

Jan 1, 1930

By H. E. Lee, P. C. Feddersen

Greenockite is the only known cadmium mineral of importance. It occurs rather universally, in minor concentrations, as a secondary mineral in sphalerite deposits. The world's cadmium output is obtained through the processing of metallurgical by-products, largely from the treatment of residues from electrolytic zinc, retort zinc and lithopone plants. These sources are supplemented by the processing of fumes from lead and copper smelting operations. The development of modern selective flotation practice in the decade 1920-1930, which permitted the economical mining of complex lead-zinc ores, resulted in significant increases in the quantities of cadmium entering lead smelting systems. Being closely related to zinc as to occurrence, properties and production, most detailed description of cadmium recovery methods are to be found recorded in connection with zinc metallurgy. Other than occasional articles pertaining to particular operational procedures, literature offers but little in the nature of a balanced survey of lead smelter cadmium recovery practices. While many of the basic operations described for the recovery of cadmium from zinc by-products are applicable to the treatment of lead plant products, the inherent problems involved differ widely. In general the cadmium content of related by-products from routine lead smelting operations is present in lower concentrations, exists in a less soluble state and is associated with both a greater quantity and a greater variety of detrimental impurities. To cope with these problems, lead smelter practices are found to follow the general outline: Preparatory Processing 1. Concentration operations 2. Sulphation operations Cadmium Plant Processing 1. Leaching operations 2. Purification operations 3. Sponge precipitation operations 4. Metal recovery operations 5. Refining and casting operations As in the case of related zinc plant operations, cadmium recovery practices at lead smelters are not standardized. They not only vary as to type, but also extent. Depending upon prevailing conditions, lead smelter cadmium operations range from simple concentration campaigns, for the purpose of sufficiently "up-grading" products for shipment elsewhere, to complete processing steps for the production of refined metal. Preparatory Processing The cadmium content of lead smelter receipts is low and, as a rule, proportionate to the zinc content; the usual range of cadmium contained being of the order of 0.01-0.05 pct. Were it not for the low boiling point of cadmium, such small concentrations would, no doubt, be lost in the large tonnages of slag, metal and other smelter end products. However, the ready volatility of cadmium and its compounds at prevailing lead smelting temperatures results in its concentration in fractional portions of fume collected. This collected fume comprises a circulating load within the smelter system. Thus, the cadmium content of blast furnace fume* increases with each successive circulation until an equilibrium value is reached when the sum of the cadmium losses, due to handling and in slag, waste gases and other end products, becomes equal to the intake as ore. With ore receipts averaging, say 0.03 pct cadmium, the concentration value obtainable, through fume circulation in a routine manner, approaches 10-12 pct. In such operations, cadmium concentrations in blast furnace fume of from 3-5 pct are readily .attainable. However, the concentration gain beyond this range, with each additional circulation, is progressively decreased as a result of mounting losses occurring through handling and in end products. Therefore, to avoid excessive cadmium loss and to enhance the ultimate concentration anttainable, it is customary practice to isolate blast furnace fume at some intermediate cadmium content for special concentration procedure. The most common type cadmium concentration "campaign" involves special smelting operations wherein a relatively high portion of blast furnace fume at 3—6 pct cadmium is incorporated into the sinter charge. This type practice is roughly illustrated by the diagram on p. 111. Cadmium fume collected from lead blast furnace operations is not amen-

Jan 1, 1950

By E. J. Schmitz

The following abstract of an unpublished treatise, prepared by me, on the geological formations and minerals of the State of Alabama, is deemed of interest to the Institute. This State, called after the river of the same name (which, formed by the junction of the Coosa and the Tallapoosa, waters, with its tributaries, more than half the State), is divided by its main watershed into a larger southern district, sloping south and southwest, and drained into the Gulf of Mexico, and a smaller northern district, sloping generally north and west, and drained into the Tennessee. Geologically the State may be divided (according to historical geology) according to the different formations it exhibits, among which I include the Azoic, the existence of which in Alabama has been doubted by some; or it may be divided (according to structural geology, as closely related to topography) into a north and northwestern, a middle, and a southern zone.

Jan 1, 1884

By William C. Aitkenhead, John A. Jaekel

Uranium deposits in the Spokane Indian Reservation, as well as those around Mt. Spokane, are essentially low grade, much of the ore containing less than 0.2 pct U808. The Mining Experiment Station of the Division of Industrial Research, State College of Washington, has been engaged in intensive research on the amenability of these low grade ores to froth flotation. The results: successful flotation of autinite, chief mineral constituent. At the outset of this work the goal was a concentrate of 1 pct U308 with a 90 pct recovery from ores containing less than 0.2 pct U3O8. Most of the work has been done on argillite ore from the Midnight mine on the Spokane Indian Reservation. The goal has not been attained using this ore, but samples of the granite ore from Mt. Spokane yielded successful results. For example, a concentrate containing 11.2 pct U308 was produced from a Mt. Spokane high grade ore containing 1.27 pct U3O8 with a recovery of 97.8 pct. Another Mt. Spokane ore yielded a concentrate of 5.0 pct U3O8 from an ore containing 0.13 pct U3O8, with a recovery of 85 pct. This same ore gave a recovery of 93.5 pct when the grade of concentrate was reduced to 2.0 pct.

Jan 1, 1959

By Glenn C. Waterman

Richard Strong (Oliver Iron Mining Div., U. S. Steel Corp.)—Mr. Waterman states (p. 59, Trans., January 1954): "Core-sludge combining factors have been calculaied for any combination of core-sludge recovery on the basis of several logical assumptions: 1—The sludge sample loses reliability geometrically as sludge recovery drops. 2—The sludge sample should not be used if the percentage of sludge return is less than the percentage of core recovered. 3—A core sample should receive a weighting at least equal to the percentage of core recovery." Assumptions 1 and 2 seem justified at Chuquicamata and most geologists would agree to the validity of assumption 3. However, contrary to the statement quoted above, the core sample does not in general receive a weighting at least equal to the percentage of core recovery when the Chuquicamata methgd is used. Furthermore, the basic Chuquicamata method is identical to the Longyear or relative volume core-sludge assay combining method. Finally, the Chuquicamata method does not, in its present form, reflect true geometric loss in sludge sample reliability according to the relationship L = AR (N-1) The basic equations representing the two steps of the Chuquicamata method can be combined algebraically as follows (using the symbology of the original article except as noted): Vol A + B Assay 2 = ASA = Assay 1 Vol A VolB Core Assay [I] Vol A CA.F + ASA (100 —F) Combined grade =[21 100 Pct where F and (100 — F) are the core and adjusted sludge assay factors from Fig. 3. Substituting Eqs. 1 and 2 and collecting terms Combined grade = Vol B Vol A + B CAF (100—-F) + Assay 1 (100-F) Vol A Vol A 100 pct Eq. 3 is a unified and general statement of the Chuquicamata method. The true core factor includes not only the factor F from Fig. 3 but also the quantity VolB ------------- (100 — F), which is implicit in the value of Vol A the adjusted sludge assay. This quantity is real and positive for all values of F and core recovery less than 100. Therefore the true core factor is always less than F except when F is equal to 100. If sludge recovery is 100 pct, Eq. 3 can be further simplified as follows: Let F = percentage of core recovered. Let Vol A = Vdh (100 Pct — Pct CR) where Vdh is the total volume of the sampled interval and let Vol B = (Vdh — Vc.) Pct CR where V, is the core volume in the sampled interval at 100 pct core recovery. Then combined grade = Vo V. CA Pct CR- + Assay 1, 100 Pct — Pct CR Vdh Vdh [4] 100 Pct Eq. 4 shows that when sludge recovery is 100 pct the laboratory sludge assay receives significant weight in the Chuquicamata method, even at 100 pct core recovery. The maximum weight assigned to the laboratory sludge assay depends on drillhole size, as follows: Eq. 4, with suitable changes in symbology, is identical to Royce's formula 8,' which is a statement of the Longyear or relative volume method of combining core and sludge assays. If Mr. Waterman's assumption 3 is of paramount concern to the geologist, the Royce method (for core recoveries of 60 pct and above) or a method employing the percentage of core recovered as a core weighting factor are the only recognized methods known to the writer which achieve the desired result. A modification of the latter method embodying Mr. Waterman's assumptions 1 and 2 would result from applying the factors from Fig. 3 directly to the laboratory core and sludge assays.

Jan 1, 1956

By Charles Will Wright

THOSE that attended the seventeenth International Geological Congress held in Russia last summer had an excellent opportunity to gather data and to form impressions on the progress made in the industrialization of the country, particularly with regard to the mineral industries. Several trips to places of interest were arranged, supplementary to the technical sessions held in Moscow, the one to the Ural region being that which I selected as being most likely to be of interest. The accomplishments of the last decade in opening up new mines and building new metallurgical plants in the Soviet Union have been outstanding. This could only be accomplished by a central government ready to employ the best technical talent, which was

Jan 1, 1937

By A. S. Malicsi, I. Iwasaki

The removal of hydrophobic coatings of flotation collectors from iron ores becomes of interest when a duplex flotation process is considered for upgrading, when a pelletizing process is considered for a concentrate floated with a fatty acid or a soap collector, or when a disposal of froth products from cationic silica flotation is of environmental concern. Ozone can oxidize organic compounds rapidly, thereby removing the hydrophobic coatings of flotation collectors. Ozone is widely used for treating and purifying drinking water, waste water treatment, and for chemicals processing (Murphy and Orr, 1975; Rice et al., 1980). Its uses in metallurgical operations, however, are very sparse (Allegrini et al., 1970; Chernobrov and Rozinoyer, 1975; Ishii et al., 1970; Iwasaki and Malicsi, 1985; Matsubara et al., 1978). Yet, its high reactivity and the absence of potentially hazardous byproducts become of interest in destroying flotation reagents adsorbed on mineral surfaces or remaining in mill water for recycle or for discharge. Duplex Flotation A duplex flotation process, as applied to oxidized iron ores, would involve a fatty acid flotation of iron minerals followed by an amine flotation of the siliceous gangue from the rougher iron concentrate. Such a process has been used in the Florida phosphate fields. Fatty acid coatings cannot be removed as readily with a simple acid or alkali treatment from iron oxide surfaces as from Florida phosphates. A combination of reagents, such as lime and quebracho, lime and alkali phosphate, or sulfuric acid and oxalic acid, has therefore been proposed. In a previous article (Iwasaki et al., 1967) , the use of activated carbon was found to be effective in removing fatty acid coatings both in the duplex flotation and the pelletizing processes. The use of ozone offers another approach to the removal of fatty acid coatings from iron oxide surfaces. To investigate the possible application of the duplex flotation process, a specularite ore from Michigan analyzing 36.5% iron was used. A 600-g (1.3-1b) sample was ground in a laboratory rod mill together with 250 g/t (0.5 lb per st) of sodium silicate to -150 µm (-100 mesh). This was transferred to a Fagergren laboratory flotation cell, and deslimed four times at 20 µm (quartz equivalent). The deslimed pulp was transferred to a laboratory conditioner, diluted to 40% solids, and conditioned with 250 g/t (0.5 lb per st) of soda ash and 250 g/t (0.5 lb per st) of oleic acid. The conditioned pulp was then transferred back to the Fagergren cell, floated until barren of froth, and the rougher froth product was returned to the cell and cleaned. The results are presented in Table 1. The cleaner concentrate at this point analyzed 45.3% Fe. The cleaner concentrate coated with fatty acid was transferred to a 2-L (0.53-gal) beaker. While the pulp was agitated with a glass T-stirrer, ozone was bubbled into the agitated pulp for 15 minutes at a rate of 10 mg/min (0.00035 oz per min) ozone (250 g/t or 0.5 lb per st 03 feed). It was observed that the pulp ceased to froth after about 10 minutes. The amine flotation of siliceous gangue from the ozonated pulp was carried out first by conditioning with a dextrin, a commonly used starch depressant for iron oxides. This was followed by flotation with a stage addition of an ether amine at increments of 100 g/t (0.2 lb per st). Three stages were required to float the siliceous gangue to near completion. The three froth products were combined and cleaned twice. When the cationic flotation Rougher, Cleaner 1 and Cleaner 2 cell products were combined, an iron concentrate analyzing 64.5% iron was obtained at an overall iron recovery of 72.8%. Pelletizing Fatty acid flotation concentrates have been pelletized successfully in northern Michigan mills. But at other locations, fatty acid coatings on iron flotation concentrates proved so undesirable in agglomeration that other methods of concentration had to be sought. For example, a sinter mix containing iron ore concentrates upgraded by fatty acid flotation resulted in decreased productivity. This occurred because the micropellets of particles with the hydrophobic coating are less tolerant of moisture. Thus, the bed permeability is lost (Beebe, 1965). The agglomeration of concentrates obtained by the fatty acid flotation alone, and the hydrophobic coatings destroyed by ozonation or by the duplex flotation process, is not expected to cause any difficulty since the surfaces of the concentrates would be hydrophilic. Removal of the fatty acid coating with activated carbon, indicated by the loss of floatability, was shown to restore the decrepitation temperature of wet balls during drying cycle (Iwasaki et al., 1967). Disposal of Cationic Silica Flotation Froths Recent demands of iron blast furnaces place the silica content of the magnetic taconite pellets at about 5%. Conventional process for magnetic taconite involving fine grinding and magnetic separation often produces magnetic concentrates analyzing in excess of 5% silica. This is due to the presence of the middling grains of siliceous gangue and magnetite. Cationic silica flotation of magnetic taconite concentrates (DeVaney, 1949) may be used to reduce the silica content. But the amine coating on siliceous gangue becomes of environmental concern when the flotation tailings are discarded in tailing ponds.

Jan 1, 1986

By J. W. Lacey, F. H. Brinkman, J. E. Faris

This paper presents an analysis of the high-pressure, gas-driven LPG-slug process, based on fluid flow tests in areal models. Two types of tests were made. One series was made in low-pressure models which permitted observation of fluid movement. Three completely misci-ble analog fluids were used. A second series of tests was made in high-pressure models using methane, propane and a light refined oil saturated with methane at room temperature and 1,550 psig. Under the test conditions of room temperature and a pressure level of 1,550 psig, the phase diagram for the fluids used is similar to those for many of the field systems where the process is considered for use. A method for using these laboratory data to calculate field performance of the process is outlined. As a result of this work, it is concluded that small banks of LPG (5 per cent HV or less) are not effective in increasing oil recovery in horizontal reservoirs. Znstead, where small banks are used, the driving gas quickly penetrates the LPG bank because of fingering and channeling; and from this point on, the process behaves essentially as an immiscible gas-injection project. The validity of this conclusion was substantiated by: (1) laboratory studies of the effect of rate, model size and mobility ratio on miscible displacement in areal models; and (2) calculation of field recovery, which compared closely with actual field recovery. INTRODUCTION Field applications and pilot tests of the gas-driven, LPG-bank, oil-recovery process are on the increase. Most of these tests are employing small banks (2% to 5 per cent hydrocarbon volume) of LPG, which is miscible with both the driving gas and the oil in place, in an effort to attain an effective yet economical miscible displacement of oil by gas. The expectation of miscible displacement with small banks is based on the concepts that: (1) lengths of solvent-oil mixed zones, measured during miscible displacements in long slim cores, are representative of those that will occur in the field; and (2) areal sweep efficiencies5 measured in electrolytic model studies are applicable to miscible displacement in reservoirs. Our experimental evidence indicates that the mixed-zone lengths and sweep efficiencies mentioned are not applicable to miscible displacement in reservoirs. In this paper we present an evaluation of the gas-driven, LPG-bank oil-recovery process based on fluid flow experiments in areal models. These results are used to predict the performance of a field pilot test of this process, and the results are compared with the actual test results. THE EFFECTIVENESS OF LPG BANKS The effectiveness of LPG banks of various sizes in accomplishing miscible displacement of oil by gas was determined by displacement tests in a model representing one-quarter of a confined five-spot pattern. The model, 12 X 12 X 1/4 in. in size, was packed uniformly with glass beads. It was operated at a pressure of 1,550 psig and at room temperature; the fluids used were methane, propane and refined oil saturated with methane at 1,550 psig. The saturated oil had a viscosity of 1.2 cp at room temperature. The results of these tests are shown in Fig. 1, where recovery is plotted as a function of the volume of fluid injected for: (1) an immiscible-gas drive with an oil-to-gas viscosity ratio of 85; (2) three sizes of LPG banks; and (3) two completely miscible displacements with mobility ratios of 85:1 and 10:1. (The miscible displacement data plotted are the averages of several tests.) The results show that a 2½ per cent bank of LPG does not increase oil recovery over that obtained by immiscible-gas drive. The 7 and 17 per cent banks are, respectively, about 30 and 50 per cent effective (with reference to the M = 85 miscible-displacement curve) in increasing oil recovery at the point where 2½ hydrocarbon volumes (HV) of fluid have been injected. The percentage effectiveness of the banks at a given volume of fluid injected is defined as Recovery by Bank — Recovery by Gas Drive Recovery by Miscible Recovery by Flooding Gas Drive We conclude from these results that banks of LPG smaller than about 5 per cent HV in an individual stratum will cause from little to no increase in oil recovery. This finding was substantiated by work in low-pressure models, which permitted visual observation of fluid movements. In these tests, three completely miscible fluids having the same viscosity ratios as those used in

By Benjamin C. Allen

The surface tensions of liquid chromium and manganese were determined by a modification of the dynamic drop-weight method and found to be, respectively, 1700 * 50 and 1100 * 50 dynes per cm at their melting points. Molten drops were formed LITTLE is known about the surface tension of liquid chromium and manganese, even though they are technologically important metals and widely used in steelmaking. In the past, direct determinations have been hampered by their high reactivity on the lower end of a vertically held rod inductively heated under argon. The technique essentially reproduced surface tensions reported for liquid nickel and zirconium using static drop-shape methods. and vapor pressure. In this work, surface tensions were measured by the drop-weight method, using induction heating under argon. EXPERIMENTAL WORK Chemical analyses of rods used are given in Table I. Chromium rods were prepared from iodide-process crystals which had been are-melted, hot-extruded, warm-swaged, and centerless-ground.'

Jan 1, 1964

By T. Egleston

The necessity of using a refractory material capable of much greater resistance to chemical action and having a far higher melting-point than those which contain silica, which melt and sweat off in the furnace even when not exposed to bases forming with silica more or less fusible compounds, has led to a careful practical study of all those materials which contain very refractory bases. The results of these researches, extending over several years, and made on a very large scale in many of the largest works in Europe, are of the highest interest, not only considered as a step in the progress of the study of the materials themselves, but in the application of refractory materials to metallurgical uses in general. The result of the experience of the last seven years with these basic materials, as in general with all such substanccs, is that natural products cannot be used as such. They are either too uncertain in their quality, contain substances which may in certain cases be very injurious, or, when in a condition in which they might be used, are so rare as to become practically unavailable for employment on a large scale. The materials that may he used are therefore not only limited in number. but they must be prepared artificially. When the use of basic artificial material is further extended, no doubt the number of these substances will not only be greatly increased, but the methods of preparation will be both perfected and cheapened to such an extent as to permit their application in processes for which they have hitherto proved too expensive. The quantity of refractory materials required for making ingots will he from 130 to 150 Ibs. per ton, or between 6 and 8 per cent. of the metal produced. In an establishment producing 2000 to 3000 tons of steel per week, considerable space is required to handle the basic materials properly. It is proposed in this paper to briefly discuss these basic materials and their application in the only two metallurgical processes where they have as yet been applied. These are the basic Bessemer and the basic open-hearth process, known as the Thomas-Gilchrist processes.

Jan 1, 1886

By R. F. Stewart, A. W. Hall

A method has been developed for continuously measuring the moisture content of coal. The method is based on the thermalization of fast neutrons by hydrogen in the coal. Neutrons from a small radio-isotope source penetrate the coal, are scattered by hydrogen, and measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. In a pilot-scale system, moisture was measured continuously within 0.2% in coal moving at rates up to 20 tph. The method is adaptable in industry for continuously measuring the moisture content of coal at high tonnage flow rates. Such an application would permit continuous recording of moisture in coal without sampling and facilitate quality control. An automatic and continuous method of measuring the moisture content of coal is needed by the coal industry. Automatic control of the coal quality would reduce the cost of coal preparation, improve the product, and thus indirectly increase the use of coal. Moisture in coal can be determined by several methods, but the time required to obtain samples and analyze them by existing methods makes it difficult, if not impossible, to control the quality of the product. Both producers and consumers need a method for continuous and instantaneous measurement of moisture content without sampling in order to regulate process equipment and keep the moisture content of coal within specifications. At the Morgantown, W. Va., Coal Research Center we are developing a nuclear method for continuous measurement of moisture in coal. This method is based on the thermalization of fast neutrons by hydrogen in the water and organic matter of coal. Neutrons from a small radioisotope source penetrate the coal, are scattered by hydrogen, and are measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. Design of a moisture meter based on neutron thermalization depends on many variables, any or all of which can affect the sensitivity of the meter. These factors include those related to the nuclear aspect; type and size of neutron flux and source, type of detecting device, and background count; and those related to the coal being tested: rank, particle size, and ash content. A survey was initiated to eliminate the relatively insignificant factors and to ascertain the magnitude of the major effects. Such information was necessary to fully evaluate the technique and to establish design criteria. Coal contains a relatively large amount of hydrogen in the organic coal substance and the water of hy-dration of the shaly material as well as in the moisture. To apply this concept of moisture measurement to coal requires that the organic substance in coal from any one seam of a particular mine be uniform in hydrogen content. The difference in total hydrogen content of wet and dry coal is relatively small, so that a moisture measurement based on this concept requires a measurement between two large numbers to a high degree of precision. Thus, it was necessary to develop a highly precise instrumentation system for continuous measurement and to obtain a physical arrangement permitting measurement of moving coal with a minimum effect from density variation. EXPERIMENT WITH TRAYS OF COAL Tests were conducted with metal trays containing SO to 100 lbs of coal to develop an instrument system of high precision. A scaling system with a maximum instrument error of 0.2% was used to test different types of thermal neutron detectors. The most suitable type of detector was a boron-10-lined proportional counter tube. While this type of detector showed satisfactory stability, extensive testing disclosed a long-term count reduction probably due to some type of deterioration in the detector. However, development of an electronic system using dual detectors eliminated this deterioration as a serious problem. (The second detector would be used to measure a reference drum of dry coal — the difference in count rate between the wet coal and dry reference coal being a direct measure of moisture content.) Table I, column 1, shows typical results with a 1-curie plutonium-beryllium neutron source and a thermal neutron detector beneath a tray of coal and illustrates the precision of measurement. Consecutive measurements (indicated in Table 1, columns 2-5) of thermal neutrons at various times and positions be-

Jan 1, 1968

By W. R. Ingalls

Jan 1, 1922

By W. R. Ingalls

Jan 1, 1922

By Narendrakumar A. Chevli

Exploratory work was conducted in the fabrication of integrated circuitry, specifically linear amplifier circuits, by three general methods: 1) monolithic diffused silicon; 2) a combination of metal thin-film and monolithic diffused silicon; and 3) a hybrid of metal films and diffused silicon on an alunina substrate. In these linear amplifier integrated circuits the followzng conditions were desired: very high-frequency response, high voltage gain, and good thermal tracking stability of electrical characteristics. The resulting circuit designs imposed problems of isolation between elements, layout and smallness of size of active elements, and close tolerances on electrzcal characteristics of the passive elements. Interconnection problems for specific designs resulted from the small dimensions involved and the topography of the hybrid fabrication techniques. The desired integrated-circuit characteristics were achieved with the technologies of categories 2 and 3 above. Solutions to the problems imposed by these characteristics lay in the ability to isolate czrcuit elements of small size while providing a layout designed to minimize element-to-element variations. Sufficient freedom in the formation of passive elements was achieved by uniting the metal film and the monolithic silicon technologies. The most satisfactory designs were based on the beam-lead interconnection and isolation technique. SINCE the advent of integrated circuits, major emphasis has been on fabricating digital integrated circuits. Linear circuits require high performance, high voltage, and tighter tolerance components which are not always compatible with the capability of process technology available for fabrication of these circuits into integrated form. Fortunately the growth of newer and improved processes and materials for fabricating integrated circuits has been an accelerated one. This has now made possible the translation of stringent performance requirements of the linear circuits into microminiature integrated circuits of the same performance. In the exploratory work of fabricating high-performance Linear Integrated Circuits—LIC, the following objectives were formulated: i) fabrication of high-frequency transistors such as the type 2N918 isolated on a single silicon substrate; ii) fabrication of medium-frequency transistors having a very high gain at low collector currents such as the types 2N930/2N2484 isolated on a single substrate ; iii) fabrication of tight-tolerance, high-valued resistors having low temperature coefficients of resistance and stable thermal tracking characteristics, these resistors to be fabricated on an active or passive substrate; iv) simultaneous fabrication of complementary transistors—pn and pnp-on the same silicon substrate; v) fabrication of newer active elements such as MOS, FET transistors along with the conventional active and passive elements on the same silicon substrate. State-of-the-art assessment f all the available processes, materials, and technology to meet above objectives indicated that economic fabrication of LIC cannot be achieved by a single technology for all types of linear circuits. Where design and performance of a given linear circuit can be modified and tolerated to the extent of a particular technology, then alone is it possible to fabricate a LIC using a single process technology such as all diffused, planar technology. In order to evaluate this economic breakpoint with design and performance compromise in fabricating LIC, it is essential that a thorough understanding be obtained of techniques, potentials, and limitations of all the various process technology and materials

Jan 1, 1967

By B. Ladanyi

The problem of rock behavior under concentrated loadings has been the subject of a number of studies in the past and has been receiving increasing attention by rock mechanics investigators in recent years. Its application covers various fields, but main interest in its solution has arisen in connection with the problems of drilling, bearing capacity, and rock testing. These widely different purposes and fields of interest probably have been one of the reasons why, in spite of the large amount of published experimental data and several theoretical studies, there are still many points which need further clarification. Another reason for this situation undoubtedly is due to the fact that the rock behavior in indentation is complicated by a great number of influencing factors. Experimental evidence shows that, depending on the rock type (mechanical properties, porosity), environment (ambient effective pressure, pore fluid, temperature), and the type of loading (indenter shape, initial embedment, load level, loading rate), the rock response to indentation may vary within very large limits. The widely different rock behavior has made it impossible up to now to treat the problem with a consistent single mathematical theory, but has required instead a series of simplified models covering only certain most important events in the failure sequence. As far as the theory of rock indentation is concerned, this chapter does not add much new information. Its main purpose is, however, to state the indentation problem in a general manner and to indicate which points need to be studied in more detail before its definite solution is attempted. Also, since excellent reviews of the state-of-art of rock indentation in drilling have recently been given,1-4 this will not be repeated here, and only references pertinent to the points of the problem under study will be quoted. The theoretical part of this study attempts to give a quantitative evalu-

Jan 1, 1972

By R. A. Cunningham, A. S. Murray

If a dense fluid such as mud or water is used for circulation, the formation drilled is influenced by a hydrostatic pressure. This pressure depends on hole depth arid drilling fluid density. Laboratory tests indicute that drilling rates in many forri~ations are decreased with increased pressure,—in some cases as much as 90 per cent. A comparison between laboratory and field tests indicates that drilling fluid head affects drilling rates in the field approximately the, same as in the laboratory. Drillirrg rates of many formations are increased by reducing drilling fluid head. INTRODUCTION For many years it has been noted that field and laboratory drilling rate tests did not agree even when the formations tested were the same. For instance, tests of some shales by the Hughes Tool Co. laboratory indicated drilling rates approximately 20 to 30 ft/hour, whereas in the ground this shale would drill only 3 to 5 ft/hour. A possible reason for this discrepancy is the effect of the high pressure which the drilling fluid exerts against the formation at the bottom of the hole. Consider a small element of rock (Fig. II that is to be removed by a rock bit. If the hole is filled with mud or water. the upper surface of the rock element is subjected to a pressure which depends on hole depth and fluid density. The mass of earth around this rock element presses against the circumferential surface and the lower surface. Because of the probability of shearing stresses between the rock element and the surrounding rock, this element is not under true hydrostatic stress. However, as a first approximation for test purposes the rock element was assumed to he under hydrostatic stress. The effect of hydrostatic pressure on some physical properties of rock has been studied.1,2,3 These tests show that the "differential" compres-sive stress:': necessary to cause rup- ture in rock cylinders is greater when tested under high hydrostatic pressure than when tested under atmospheric conditions. These tests were made with pressures greater than 20,000 psi which is in excess of those normally encountered in oil well drilling. Similar tests were made by the Bureau of Reclamation' using pressures equivalent to those encountered in oil well drilling. Again the "differential" compressive stress necessary to produce failure increased with increasing hydrostatic pressure. These tests indicated that drilling rates would probably decrease. Correlation between these tests and drilling tests was not practical. The purpose of this work is to study the effect of mud column pressure on drilling rate, assuming that the material drilled is in a state of hydrostatic strcss. This problem was initially investigated in the laboratory using variable bit loads and confining pressure;. Confirmation of laboratory results was obtained in the field from a series of carefully controlled drilling tests. Because of the necessity of testing many different types of formations. only results from representative formations will be presented here.

Jan 1, 1956